Grizzly H6146 34 Degree Clipped Head Framing Nailer Owner Manual

Grizzly H6146 34 Degree Clipped Head Framing Nailer Owner Manual

34° CLIPPED HEAD FRAMING NAILER

MODEL H6146

INSTRUCTION MANUAL

COPYRIGHT © FEBRUARY, 2005 BY GRIZZLY INDUSTRIAL, INC. REVISED DECEMBER, 2017 (HE)

WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.

#BL6906 PRINTED IN CHINA

SECTION 1: SAFETY

For Your Own Safety Read Instruction Manual Before Operating This Equipment

The purpose of safety symbols is to attract your attention to possible hazard ous conditions. This manual uses a series of symbols and signal words which are intended to convey the level of importance of the safety messages. The progression of symbols is described below. Remember that safety messages by themselves do not eliminate danger and are not a substitute for proper accident prevention measures.

NOTICE

Indicates an imminent hazardous situation which, if not avoided, WILL result in death or serious injury.

Indicates a potentially hazardous situation which, if not avoided, COULD result in death or serious injury.

Indicates a potentially hazardous situation which, if not avoided, MAY result in minor or moderate injury. It may also be used to alert against unsafe practices.

This symbol is used to alert the user to useful infor mation about proper operation of the equipment.

Safety Instructions for Pneumatic Tools

KEEP ALL SAFETY DEVICES IN PLACE

and in working order.

REMOVE ADJUSTING KEYS AND

WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before operation.

KEEP CHILDREN AND VISITORS

AWAY. All children and visitors should be kept at a safe distance from work area.

MAKE WORKSHOP CHILD PROOF by locking the shop and shutting off air valves.

KEEP WORK AREA CLEAN. Cluttered areas and benches invite accidents.

DO NOT USE IN DANGEROUS

ENVIRONMENT. Do not use pneumatic tools in damp or wet locations, or where any flammable or noxious fumes may exist. Keep work area well lighted.

DO NOT FORCE TOOL. It will do the job better and safer at the rate for which it was designed.

USE THE RIGHT TOOL. Do not force tool or attachment to do a job for which it was not designed.

DO NOT USE UNDER INFLUENCE OF DRUGS OR ALCOHOL.

Safety Instructions for Pneumatic Tools

USE PROPER AIR HOSE for the tool. Make sure your air hose is in good condi tion and is long enough to reach your work area without stretching.

DISCONNECT TOOLS before servic ing, changing accessories, or moving to another location.

WEAR PROPER APPAREL. Do not wear loose clothing, gloves, neckties, rings, bracelets, or other jewelry which may get caught in moving parts. Non-slip footwear is recommended. Wear a protective hair covering to contain long hair.

ALWAYS USE SAFETY GLASSES. Also use a face or dust mask if operation is dusty. Everyday eyeglasses only have impact resistant lenses, they are NOT safety glasses.

AWKWARD POSITIONS. Keep proper footing and balance at all times when operating tool. Do not overreach! Avoid awkward hand positions that make work piece control difficult or increase the risk of accidental injury.

USE RECOMMENDED ACCESSORIES. Consult this owner’s manual or the manu facturer for recommended accessories. Using improper accessories will increase the risk of serious injury.

NEVER LEAVE UNATTENDED TOOL

CONNECTED TO AIR. Disconnect the air hose and do not leave tool until it is relieved of any built up pressure.

NEVER ALLOW UNTRAINED USERS TO USE THIS TOOL WHILE UNSUPERVISED.

WEAR APPROVED HEARING

PROTECTION. Air escaping from pneu matic tools can exceed safe exposure limits and may cause hearing damage with prolonged exposure.

IF YOU ARE UNSURE OF THE INTENDED OPERATION, STOP USING

TOOL. Seek formal training or research books or magazines that specialize in pneumatic tools.

BE AWARE OF HOSE LOCATION WHEN

USING PNEUMATIC TOOLS. Hoses can easily become a tripping hazard when laid across the floor or spread out in a disorga nized fashion.

REDUCE THE RISK OF

UNINTENTIONAL FIRING. Do not carry tool with hand on trigger and always dis connect from air when not in use.

SECURE WORK. When required, use clamps or vises to secure workpiece. A secured workpiece protects hands and frees both of them to operate the tool.

CHECK FOR DAMAGED PARTS.

Regularly inspect tool for any con dition that may affect safe operation. Immediately repair or replace damaged or mis-adjusted parts before operating tool.

MAINTAIN TOOLS WITH CARE. Keep tools lubricated and clean for best and safest performance. Follow instructions for lubricating and changing accessories.

H6146 34° Clipped Head Framing Nailer -1 -

Additional Safety Instructions for Nailers/ Staplers

1. HAND INJURIES: Do not place your hands near the nail/staple point of entry. A nail/staple can deflect and tear through the surface of the workpiece, puncturing your hand or fingers.

2. COMBUSTIBLE GASES: Never con nect the nailer/stapler to pressurized oxygen or other combustible gases as an air source air.

mechanism.

. Only use filtered, lubricated, and regulated compressed 3. SAFE HANDLING: Never point the nailer/stapler at others! Do not keep the trigger pulled when loading fas teners, carrying, or holding tool. Carry the tool only by the handle, never by any other part. Do not carry the tool by the air hose. Disconnect the nailer/ stapler from the air hose when going up and down ladders.

4. MODIFICATIONS: DO NOT modify this tool or bypass the safety nose 5. COMPRESSED AIR RATING: Do not connect the nailer/stapler to com pressed air that exceeds 120 PSI.

6. HOSE USAGE: Make sure your air hose is designed for the tool in use, is in good condition, and is long enough to reach your work without stretching. However, an overly long air hose in the work area may be a tripping haz ard.

7. OPERATING QUESTIONS: If you are not sure about the intended oper ation, stop using the nailer/stapler. Seek formal training.

8. CLEANING: Never use gasoline or other flammable liquids to clean the nailer; vapors in the nailer/stapler will ignite by a spark and cause it to explode.

9. MAINTENANCE: Always disconnect air from the nailer/stapler when ser vicing or installing nails. During main tenance, a nailer/stapler connected to air may fire accidentally, causing serious personal injury.

4. CHECK VALVE: Do not use a check valve or any other fitting that allows air to remain in the tool after it is dis connected from the air source.

-2 H6146 34° Clipped Head Framing Nailer

Never point this nailer at yourself or another person! Always pay attention to the direction this nailer is pointed. Use this tool with respect and caution to lessen the possibility of operator or bystander injury. Ignoring this warning may result in serious personal injury.

Operating this nailer can propel objects into the air, causing imme diate eye damage. To protect your self, always wear American National Standards Institute (ANSI) approved safety glasses or goggles when oper ating this equipment. In addition, this nailer discharges at up to 85-90 deci bels. To protect your hearing, always wear ANSI approved ear protection when operating this nailer.

No list of safety guidelines can be complete. Every shop environment is different. Always consider safety first, as it applies to your individual working conditions. Use this and other tools with caution and respect. Failure to do so could result in serious personal injury, damage to equipment or poor work results.

Nailer/stapler accidents routinely hap pen while moving the gun to another location, such as up ladders, to anoth er room, or even another job site. Always disconnect the gun immedi ately after use and never transport the gun while connected to the air—even if the air compressor is disconnected from its power source!

Read the manual before operation. Become familiar with this nailer, its safety instructions, and its operation before beginning any work. Serious personal injury may result if safety or operational information is not under stood or followed.

H6146 34° Clipped Head Framing Nailer -3 -

INTRODUCTION

Foreword Contact Info

We are proud to offer this manual with your new H6146 34º Clipped Head Framing Nailer! We've made every effort to be exact with the instructions, specifications, drawings, and photographs of the nail er we used when writing this manual. However, sometimes we still make an occasional mistake.

Also, owing to our policy of continuous improvement, your nailer may not exactly match the manual. If you find this to be the case, and the difference between the man ual and nailer leaves you in doubt, check our website for the latest manual update or call technical support for help.

For your convenience, we post all avail able manuals and manual updates for free on our website at www.grizzly.com. Any updates to your model of machine will be reflected in these documents as soon as they are complete.

Machine Data

We stand behind our machines. If you have any service questions, parts requests or general questions about the machine, please call or write us at the location listed below.

Grizzly Technical Support 1815 W. Battlefield Springfield, MO 65807 Phone: (570) 546-9663 E-Mail: techsupport@grizzly.com

We want your feedback on this manual. If you can take the time, please email or write to us at the address below and tell us how we did: Grizzly Industrial, Inc.

C/O Technical Documentation Manager P.O. Box 2069 Bellingham, WA 98227-2069 Email: manuals@grizzly.com

Nail Size ................

7 ⁄ 64 " 1 ⁄ 8 " Shank Diameter Nail Strip Angle ...................................... 34º Nail Length .......... 2"-3½"(Clipped Headed) Magazine Capacity ...................... 100 Nails Air Inlet ...........................................¼" NPT Weight .............................................8

1 ⁄ 3 lbs.

Operating Pressure .................. 70-120 PSI -4 -

This nailer presents serious inju ry hazards to untrained users. Read through this entire manual to become familiar with the controls and operations before starting the machine!

H6146 34° Clipped Head Framing Nailer

SET UP

Unpacking Inventory

Your machine was carefully packaged for safe transportation. Remove the packag ing materials from around your machine and inspect it. If you discover the machine is damaged, please immediately call

Customer Service at (570) 546-9663 for advice.

Save the containers and all packing mate rials for possible inspection by the carrier or its agent. Otherwise, filing a freight claim can be difficult.

After you open the nailer box, you should find the following.

Model H6146 Inventory (Figure 1)

A. 34° Clippled Head Framing Nailer ..... 1 B. Safety Goggles ................................. 1 C. Oil ....................................................... 1 D. Hex Wrench 3mm .............................. 1 E. Hex Wrench 4mm .............................. 1 F. Hex Wrench 5mm .............................. 1 G. Hex Wrench 6mm .............................. 1 When you are completely satisfied with the condition of your shipment, inventory the contents.

If any non-proprietary parts are missing (e.g., a nut or a washer), we will gladly replace them; or for the sake of expedien cy, replacements can be obtained at your local hardware store.

B A C G F E D Figure 1. Model H6146 inventory.

H6146 34° Clipped Head Framing Nailer -5 -

Compressed Air System

The Model H6146 is designed to be oper ated at 70-120 PSI using clean, dry, regu lated, compressed air.

your model.

DO NOT exceed the maximum operating pressure for

Before using your new nailer, regulate the air pressure on your air compressor to the minimum PSI for your model.

An in-line filter/lubricator/regulator unit, depicted in as possible.

Figure 2, can be installed and should be located as close to the nailer This filter/lubricator/regulator unit will protect your tool from damaging water build-up, allow you to adjust and maintain constant air pressure to your tool, and save you the inconvenience of having to manually lubricate your tool every time you use it.

Exceeding the maximum permissible operating pressure may cause the nailer to explode, blowing metal frag ments in all directions. To protect yourself from serious personal injury, DO NOT allow your air compressor to exceed the recommended pressure when connected to this nailer!

Check the current Grizzly catalog for avail ability of this unit. If you plan on install ing a filter/lubricator/regulator unit in your compressed air system, always follow the connection instructions that come with the unit.

Quick Connector Nailer Quick Coupler Quick Connector Oiler Filter Air Hose Quick Coupler Regulator Figure 2. Filter/Lubricator/Regulator Unit.

Air Compressor -6 H6146 34° Clipped Head Framing Nailer

Safety Yoke

A safety yoke mechanism on the nose of the nailer acts as a secondary safety device. When the trigger is pressed, the nailer will not fire until the safety yoke mechanism is depressed.

Before you use your nailer for the first time, check the safety yoke mechanism to ensure proper function. To do this:

1. DISCONNECT NAILER FROM THE AIR SUPPLY!

2. Make sure the magazine is empty and contains no nails.

3. Make sure the trigger and the safety yoke mechanism move up and down without sticking.

4. Connect the nailer to the air supply.

5. Without pressing the trigger, depress the safety yoke mechanism against a scrap piece of wood that is clean and free of any knots, nails, or other foreign objects. — If the nailer does not fire, then the safety yoke mechanism is working correctly. — If the nailer does fire when you do this, immediately disconnect the nailer from the air supply and call Grizzly Technical Support at (570) 546-9663 for help.

— If the nailer fires when the trigger is pulled, without the safety yoke mechanism being depressed, then the nailer is not working properly.

— If either of these two conditions develop after you have used your nailer for a period of time, check the lubrication of these mechanisms.

The safety yoke is a mechanical device that can fail. Never rely on the safety yoke mechanism as an excuse to point the nailer at yourself or any bystanders. Serious injury may occur.

H6146 34° Clipped Head Framing Nailer -7 -

OPERATIONS

Loading

When replacing nails in your Model H6146, follow these guidelines:

Diameter: 7 ⁄ 64 " 1 ⁄ 8 " Length: 2"-3 1 ⁄ 2 " Capacity: 100 Strip Angle: 34°

To load your nailer: 1. DISCONNECT NAILER FROM THE AIR SUPPLY!

2. Grip the nailer firmly, pull the maga zine pusher back, and engage the catch lever as shown in Figure 3. Figure 4. Loading nails into magazine.

4. Slide the nails all the way down to the nose of the nailer.

5. Release the catch lever. The pusher slides forward until it rests against the nail stick.

Operating

Pusher Catch Lever Figure 3. Sliding pusher toward the catch lever.

3. Insert a strip of nails, pointed-end down, into the magazine as shown in Figure 4.

If you have not read the safety instruc tions in this manual, do not operate the nailer.

Before you operate your nailer, place five to six drops of the included oil into the quick connect fitting where the nailer con nects to the air supply.

To operate your nailer:

1. Connect the air supply to the quick connect fitting.

2. To test for proper nail penetration, hold the nailer perpendicular to the surface of a piece of clean scrap wood that is thick enough for the length of nails you have loaded. -8 H6146 34° Clipped Head Framing Nailer

3. Pull the trigger and depress the safety yoke mechanism on your workpiece. 4. Before pressing the trigger, make sure your free hand and other body parts are positioned out of the way of a potential path of a nail in case of deflection. Deflection is caused when grain irregularities, knots or foreign objects inside the wood cause the nail to change its path, resulting in the nail puncturing the surface of the workpiece, as shown in

Figure 5.

Besides damaging your workpiece, deflection can cause injury if your free hand is securing the workpiece in the location that the nail deflects.

Adjusting Depth

The nose of the gun houses a depth adjust ment mechanism for setting the nail depth.

To adjust the depth: 1. DISCONNECT NAILER FROM THE AIR SUPPLY!

2. If the nail is driven too far into the workpiece, loosen the cap screw on the safety nose with a 4mm wrench, as shown in Figure 6. Safety Nose Safety Yoke Cap Screw Figure 5. Example of nail deflection.

5. Pull the trigger. If the nail drove into the wood far enough, continue with your intended operations. If the nail either went too far or not far enough, then go to the Adjusting Depth section on this page.

Figure 6. Loosening cap screw for depth adjustment.

3. Slide the safety nose (Figure 6) toward the nailer body to drive nails deeper, and away from the body to drive nails less deep.

4. Tighten the safety nose cap screw each time after making adjustments. 5. Connect to the air.

6. Pull the trigger and depress the safety yoke mechanism on your workpiece to test the depth adjustment. H6146 34° Clipped Head Framing Nailer -9 -

Clearing Jammed Nails

A jammed nail must be cleared before using the nailer again. The two places where a nail can get jammed are the maga zine and the discharge area.

To clear a jammed nail from the maga zine: 1. DISCONNECT NAILER FROM THE AIR SUPPLY!

2. Pull back and lock the magazine push er.

3. Remove the nail stick.

4. Locate and remove the jammed nail with needle nose pliers. Release the catch lever and let the pusher slide to front of the magazine.

To clear a jammed nail from the dis charge area: 1. DISCONNECT NAILER FROM THE AIR SUPPLY!

2. Pull back and lock the magazine push er in place.

3. Remove all nails from the magazine.

4. Locate the nail in the nailer nose, dis lodge the nail with a tool that will fit in the slot on the underside of the nose. 5. Throw the damaged nail away and insert a new nail stick that only con tains clean, undamaged nails. DO NOT use dirty or damaged nails!

6. Release the catch lever and let the pusher slide to the front of the maga zine.

-10 H6146 34° Clipped Head Framing Nailer

Replacing Pistons/O Rings

If you use your nailer day in and day out, repair pistons are cheap insurance against wasted down time and lost profits, in the event that a piston or piston shaft becomes worn out.

Always disconnect air from nailer whenever servicing! During mainte nance, a nailer connected to air may fire accidentally, causing serious personal injury!

To replace a piston: 1. DISCONNECT NAILER FROM THE AIR SUPPLY!

2. Remove all nails from the magazine cartridge. 3. Remove the four cap screws on the top of the nailer, near the exhaust port.

4. Remove the top cap.

5. The top of the piston should now be visible inside the cylinder, which is housed in the head of the nailer.

6. Open the magazine.

7. Watch the discharge area and push the top of the piston with your finger. You will see the piston shaft slide down the discharge area. 8. With a long flathead screwdriver or similarly shaped tool, push the piston shaft back inside the nailer until you can grip the piston head and remove it from the cylinder. (Be careful not to scratch the discharge area when push ing the piston shaft with the screw driver.) 9. Place a new O-ring on the new piston and apply a thin film of the nailer lubri cating oil on the O-ring.

10. Insert the new piston in the cylinder. Make sure that the grooves on the piston shaft line up with those on the guide at the bottom of the cylinder. The new piston should easily slide into the cylinder.

DO NOT force the

piston into the cylinder! If the piston is not easily inserted, double-check the alignment of the piston shaft with the grooves on the guide.

11. After the piston is inserted correctly, close the magazine. Replace the top cap assembly and tighten the 4 cap screws.

12. For more assistance, or to install a complete O-ring set, refer to the appro priate breakdown diagram in the back of this manual.

H6146 34° Clipped Head Framing Nailer -11 -

CLEANING & LUBRICATION

Cleaning Lubricating

Use a good solvent to clean the nose assembly of the nailer. Always be sure that the nailer is dry before using it again. Do not allow dust, chips, sand, etc. into the air connectors or into the body of the nailer; this may result in leaks and dam age to the nailer and the air couplings.

Special oil has been included with your new Grizzly nailer to help maintain its useful life. Place two to six drops of oil in the nailer air inlet (as shown in continuous use.

Figure

7) before every use, or after 2 hours of Wipe off any excess oil near the nailer exhaust to avoid dust build-up. When the oil that was included with the nailer has been completely used, replace with Grizzly Model T28039 Air Line Oil.

Another option to manual oiling would be to install a lubricator in your air compres sor line. If your air compressor line already has a lubricator, then regular lubrication of your nailer will not be necessary. Just make sure there is always oil in the lubri cator.

As mentioned before, the best option is to install a filter/lubricator/regulator unit in your air line.

Never use gasoline or other flamma ble liquids to clean this tool. Vapors in the tool may ignite, causing the tool to explode. Ignoring this warning may lead to serious personal injury or even death!

-12 Figure 7. Lubricating nailer via air inlet.

H6146 34° Clipped Head Framing Nailer

H6146 PARTS BREAKDOWN

31 32 33 34 45 46 47 48 49 37 38 H6146 34° Clipped Head Framing Nailer -13 -

H6146 PARTS LIST

PART # DESCRIPTION

1 2 3 4 5 6 PH6146001 SPCL CAP SCR M8-1.25 X 30 PH6146002 AIR DEFLECTOR PH6146003 RUBBER WASHER PH6146004 SPRING PH6146005 SPRING WIRE PSB06M CAP SCREW M6-1 X 25 7 8 9 PLW03M LOCK WASHER 6MM PH6146008 CYLINDER CORE PSS07M SET SCREW M5-.8 X 5 10 PH6146010 CYLINDER COVER 11 PH6146011 HEAD VALVE PISTON 12 PH6146012 SPRING SEAT 13 PH6146013 COMPRESSION SPRING 14 PH6146014 O-RING 56.7 X 3 15 PH6146015 COLLAR 16 PH6146016 O-RING 42.3 X 5 17 PH6146017 PISTON 18 PH6146018 O-RING 57.5 X 3 19 PH6146019 O-RING 88 X 3 20 PH6146020 FIXED RING 21 PH6146021 SEALING RING 22 PH6146022 CYLINDER 23 PH6146023 BUMPER 24 PH6146024 GASKET 25 PH6146025 BODY 26 PH6146026 RUBBER WASHER 27 PH6146027 TRIGGER VALVE SEAT 28 PH6146028 O-RING 15 X 2.65

29 PH6146029 O-RING 17 X 1.5

30 PH6146030 TRIGGER VALVE GUIDE 31 PH6146031 O-RING 6.2 X 1.8

32 PH6146032 O-RING 6.4 X 2 33 PH6146033 O-RING 9 X 1.8

34 PH6146034 SWITCH SPRING 35 PH6146035 SWITCH PIPE 36 PH6146036 O-RING 2.5 X 1.5

37 PH6146037 O-RING 20.3 X 2.3

38 PH6146038 SWITCH SEAT 39 PH6146039 TRIGGER PIN 40 PH6146040 TRIGGER 42 PH6146042 SAFETY SPACER 43 PRP02M ROLL PIN 3 X 16 44 PH6146044 SAFETY GUIDE 45 PH6146045 PIN 3 X 25 46 PH6146046 COMPRESSION SPRING

REFPART # DESCRIPTION

47 PSB03M 48 PW02M CAP SCREW M5-.8 X 8 FLAT WASHER 5MM 49 PH6146049 ADJUSTING NUT 50 PH6146050 SAFETY YOKE 51 PH6146051 SAFETY NOSE 52 PH6146052 COPPER COLLAR 53 PH6146053 SAFETY NOSE CASE 54 PH6146054 O-RING 61.5 X 1.8

55 PH6146055 DRIVER GUIDE 56 PLW04M 57 PSB13M 58 PS14M LOCK WASHER 8MM CAP SCREW M8-1.25 X 30 PHLP HD SCR M6-1 X 12 59 PH6146059 MAGAZINE 60 PW03M FLAT WASHER 6MM 61 PLN03M LOCK NUT M6-1 62 PH6146062 DRIVE NAIL BAR 63 PSB18M CAP SCREW M4-.7 X 8 64 PLN01M 65 PSB46M LOCK NUT M4-.7

CAP SCREW M4-.7 X 40 66 PH6146066 SAFETY PIPE 67 PH6146067 SAFETY PIPE CASE 68 PH6146068 PIN CASE 69 PRP23M ROLL PIN 4 X 44 70 PH6146070 PUSHER 71 PH6146071 PIN 3 X 20 72 PH6146072 PIN 5 X 20 73 PSB93M CAP SCREW M3-.5 X 14 74 PN07M HEX NUT M3-.5

75 PH6146075 PIN 4 X 30 76 PH6146076 TORSION SPRING 77 PH6146077 SPRING CORE 78 PH6146078 PIN 5 X 12 79 PH6146079 RELEASE LATCH 80 PH6146080 TORSION SPRING 81 PSB38M 82 PW02M CAP SCREW M5-.8 X 25 FLAT WASHER 5MM 83 PH6146083 FIXED SEAT 84 PLN02M LOCK NUT M5-.8

85 PH6146085 RUBBER HANDLE CASE 86 PH6146086 GASKET 87 PH6146087 END CAP 88 PLW01M LOCK WASHER 5MM 89 PSB15M CAP SCREW M5-.8 X 20 90 PH6146090 1/4" NPT MALE CONNECT 91 PH6146091 AIR PLUG COVER 92 PW02M FLAT WASHER 5MM -14 H6146 34° Clipped Head Framing Nailer

TROUBLESHOOTING

PROBLEM

Air leaking at trigger valve area.

Air leaking between hous ing and hose.

CAUSE

1. O-rings in trigger valve housing are damaged.

1. Loose screws in housing.

2. Damaged O-ring.

3. Loose air fitting.

ACTION

1. O-rings must be replaced & operation of safety yoke must be checked.

1. Tighten screws.

2. Replace O-ring.

3. Tighten air fitting & use teflon tape.

1. Replace damaged seals.

Air leaking between hous ing and cap assembly.

Tool skips nails while dis charging.

Tool runs slowly or has a loss of power.

Fasteners frequently jam the nailer.

Nailer does not fire.

1. Damaged seal.

1. Air leaks.

2. Dirt in nose.

3. Dirt or damage prevents nails from moving freely in magazine.

4. Inadequate air flow to tool.

5. Worn O-ring on piston or lack of lubrication.

6. Damaged O-rings on trig ger valve.

7. Worn bumper.

8. Cap seal leaking.

1. Nailer is not sufficiently lubricated.

2. Broken spring in cap assembly.

3. Exhaust port in cap is blocked.

1. Nails are the wrong size.

2. Nails are bent or dirty.

3. Magazine or nose screws are loose.

4. Driver or driver guide are worn or damaged.

5. Nails are wrong angle.

1. Nail is jammed in maga zine or discharge area.

2. Piston shaft is damaged.

3. Air pressure too low.

H6146 34° Clipped Head Framing Nailer 1. Tighten screws and fit tings.

2. Clean nose.

3. Clean magazine and inspect/repair damage.

4. Check fitting, hose, com pressor & air pressure.

5. Replace piston O-ring. Lubricate.

6. Replace trigger valve O rings.

7. Replace bumper.

8. Replace cap seal.

1. Lubricate nailer.

2. Replace spring.

3. Clean or replace dam aged internal parts.

1. Use correct nails.

2. Use undamaged, clean nails.

3. Tighten magazine.

4. Replace worn or dam aged parts.

5. Use correct angle nails.

1. Clear nailer magazine or discharge area.

2. Replace piston shaft.

3. Check/increase air pres sure.

-15 -

WARRANTY AND RETURNS

Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance. This is Grizzly’s sole written warranty and any and all warranties that may be implied by law, including any merchantability or fitness, for any particular purpose, are hereby limited to the duration of this written warranty. We do not warrant or represent that the merchandise complies with the provisions of any law or acts unless the manufacturer so warrants. In no event shall Grizzly’s liability under this warranty exceed the purchase price paid for the product and any legal actions brought against Grizzly shall be tried in the State of Washington, County of Whatcom.

We shall in no event be liable for death, injuries to persons or property or for incidental, contingent, special, or consequential damages arising from the use of our products.

To take advantage of this warranty, contact us by mail or phone and give us all the details. We will then issue you a “Return Number,’’ which must be clearly posted on the outside as well as the inside of the carton. We will not accept any item back without this number. Proof of purchase must accompany the merchandise. The manufacturers reserve the right to change specifications at any time because they constantly strive to achieve better quality equipment. We make every effort to ensure that our products meet high quality and durability standards and we hope you never need to use this warranty.

Please feel free to write or call us if you have any questions about the machine or the manual. Thank you again for your business and continued support. We hope to serve you again soon.

Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement