Grizzly H7932 Heavy-Duty Conduit Bender Set Owner Manual

Grizzly H7932 Heavy-Duty Conduit Bender Set Owner Manual

MODEL H7932 HEAVY-DUTY CONDUIT BENDER SET Instruction Sheet Introduction

These instructions cover the basics to help you get your new tool assembled and ready for opera tion. These instructions do not cover how to bend conduit. If you are new to conduit bending, we suggest formal training, as this is a learned skill.

After assembly, keep this instruction sheet in a safe place so it is available if you ever need replacement parts.

Inventory

(Figure 1) A.

Conduit Bender Assembly .......................... 1

B.

Bending Die 1", 3 ⁄ 4 ", 1 ⁄ 2 " ......................1 Each

C.

Handle Extension Tube .............................. 1

D.

Pipe Vise .................................................... 1

E.

Hardware Bag (not shown) ........................ 1 — Hex Bolts M8-1.25 x 25 .......................... 3 — Flat Washers 8mm ................................. 3 —Hex Nuts M8-1.25 ................................... 3

Assembly

(Figure 2) 1.

Stand the bender assembly upright, fold the stand leg out, and insert the two pins through the stand.

2.

3.

4.

Use the hardware from the included hard ware bag to mount the vise to the bender assembly. (Secure the flat washer and nut from underneath.) Insert the handle extension tube in the stor age sleeve until needed.

Mount the loose bending die in the pivot area by aligning the holes and inserting the center pin.

A B D C

Figure 1.

Model H7932 inventory.

Handle Extension Tube Center Pin Storage Sleeve

Figure 2.

Model H7932 fully assembled.

If you need help with your new conduit bender, call our Tech Support at: (570) 546-9663.

COPYRIGHT © AUGUST, 2006 BY GRIZZLY INDUSTRIAL, INC.

WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.

#TR8501 PRINTED IN CHINA

Vise Two Pins

Operation Setup

1.

Insert the size of bending die that matches the conduit you want to bend.

2.

Move the grooved roller to the corresponding hole in the bending lever (

Figure 3

).

3.

Adjust the stop block position to the corre sponding hole in the stop bar (

Figure 3

).

Operation Tips

• The free end of the conduit should not be longer than 43" or it will touch the ground, interfering with the bend.

• Place your foot on the cross member of the main body for support when bending upwards.

Always wear safety glasses when using this item.

�������� ����������

�� ���� ����

������� ������ �������������

Figure 3.

Mounting positions in stop bar and bending lever for corresponding bending dies.

Accessories

G8692—Portable Metal Bandsaw w/Stand

Quickly cut through all your conduit with this por table metal bandsaw. At 38 lbs., this bandsaw is easy to setup and take from jobsite to jobsite. Also easily removes from stand for hand-held cutting. Features double-insulated 1 HP 110V motor and 190/262 FPM cutting speeds.

H2920—Professional Shop Bag H2918—Bucket Organizer H5773—Electrician's Tool Pouch

Keep your tools organized and always at your side with these handy products from Grizzly! Built with ballistic nylon for extreme durability and wear for years on the jobsite.

H2920

Figure 4.

G8692 Portable Metal Bandsaw.

H0901—6 PC. Bi-Metal Hole Saw Set H0902—10 PC. Bi-Metal Hole Saw Set

Popular 6 piece Bi-Metal Hole Saw Set includes 3 1 ⁄ ⁄ 4 ", 7 ⁄ 8 ", 11 ⁄ 8 ", 11 ⁄ 2 ", 13 ⁄ 4 " and 21 ⁄ 4 " Bi-Metal Hole Saws, 2 " x 20 UNF arbor, adapter and high impact plastic case. For the ulti mate hole saw selection in one complete kit, this 10-pc. Bi-Metal Hole Saw Set is tough to beat. Set includes 7 ⁄ 8 ", 11 ⁄ 8 ", 13 ⁄ 8 5 ", ⁄ 8 " x 18 UNF arbor, arbor 13 ⁄ 4 ", 2", 21 ⁄ 2 ", 3", 35 ⁄ 8 ", 41 ⁄ 8 " 5 and 43 ⁄ 4 " bi-metal hole saws, 1 ⁄ 2 " x 20 UNF arbor, ⁄ 8 " x 18 UNF arbor, arbor adapter and high impact plastic case.

H2918 H5773

Figure 6.

Ballistic nylon tool organizers.

H7793—14V Extra-Duty Cordless Drill H8861—14V Extra/Replacement Battery H7795—18V Extra Duty Cordless Drill H8863—18V Extra/Replacement Battery

These next-generation, high-quality cordless drills get the job done without breaking the bank. Each set includes the drill, two NiCd batteries, a bat tery charger, Phillips #2 bit, and carrying case. Features 0–700 RPM variable speed, adjustable clutch settings, and keyless 3/8" chuck. The per fect tool for driving screws all day long—day-in and day-out!

Figure 5.

H0901 and H0902 Hole Saw Sets.

Figure 7.

H7795 Extra-Duty Cordless Drill Set.

� �� �� ������������������ �

H7932 Parts Breakdown and List

� �� � � �� �� � ������������������ �� � �� �

REF

9 10 11 12 1 2 3 4 5 6 6-1 7 8

PART #

PH7932001 PH7932002 PH7932003 PH7932004 PH7932005 PH7932006 PH7932006-1 PH7932007 PH7932008 PH7932009 PH7932010 PH7932011 PH7932012

DESCRIPTION

BENDING LEVER HANDLE EXTENSION TUBE BENDING DIE 1/2" BENDING DIE 3/4" BENDING DIE 1" COMPLETE PIPE VISE LOWER VISE JAW STOP BLOCK STOP BLOCK BAR COTTER PIN PIVOT PIN GROOVED ROLLER CENTER PIN

REF

13 14 16 17 18 19 20 21 22 23 24 25

PART #

PH7932013 PH7932014 PH7932016 PW06M PH7932018 PH7932019 PLN09M PH7932021 PH7932022 PB07M PW01M PN03M

DESCRIPTION

SUPPORT MAIN BODY SPECIAL BOLT FLAT WASHER 12MM INSIDE SPACER SLEEVE OUTSIDE SPACER SLEEVE LOCK NUT M12-1.75

CHAIN W/RING GROOVED ROLLER PIN HEX BOLT M8-1.25 X 25 FLAT WASHER 8MM HEX NUT M8-1.25

Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement