Grizzly T28170 Heavy-Duty Shop Stand Owner Manual

MODEL T28170 TOOL STAND INSTRUCTIONS

For Models Mfd. Since 10/17

For questions or help with this product contact Tech Support at (570) 546-9663 or [email protected]

Introduction

The Model T28170 Tool Stand is designed to pro vide a stable platform for mounting machinery and equipment.

Inventory

Description Qty

A. Legs ........................................................... 4 B. End Supports ............................................. 4 C. Side Supports ............................................. 4 D. Foot Brackets ............................................. 4 E. Adjustable Feet M12-1.75 x 120mm w/ Hex Nuts M12-1.75 ................................. 4 F. Hardware Bag (Not Shown) —Carriage Bolts M8-1.25 x 20mm ........... 48 —Flange Nuts M8-1.25 ............................ 48 —Flange Nut M12-1.75 ............................... 4 —Hex Nuts M12-1.75 .................................. 4 A B Figure 1. Model T28170 Tool Stand.

Specifications

• • • • Footprint (Length x Width) ..............28" x 20" Height ...............................................31"–39" Maximum Weight Capacity ............. 400 lbs.

Approximate Assembly Time .......30 Minutes

Needed for Assembly

• Open-End Wrench or Socket 13mm .......... 1 • • Open-End Wrench 15mm or Adjustable Wrench ..................................... 2 90° Square ................................................. 1 • Level 3' ....................................................... 1 D E C Figure 2. Inventory.

COPYRIGHT © NOVEMBER, 2017 BY GRIZZLY INDUSTRIAL, INC.

NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.

#ES19303 PRINTED IN CHINA V1.11.17

Assembly

This tool stand must be fully assembled before it can be used. Before beginning the assembly pro cess, refer to Needed for Assembly and gather all listed items.

To assemble tool stand:

1. Build one side assembly by attach ing (2) side supports to (2) legs with (8) M8-1.25 x 20 carriage bolts and (8) M8-1.25 flange nuts (see are perpendicular (see Figure 3). Use 90° square to make sure legs and supports Figure 3). Note: There are two sets of holes at top-end

of legs for side supports. Use lower set of holes if you plan to attach a table top with a drawer or a vise to tool stand.

x 8 Side Supports 90° Square 3. Attach (4) end supports to side assembly made in (see (see Step 1 with (8) M8-1.25 x 20 car riage bolts and (8) M8-1.25 flange nuts Figure 4). Use 90° square to make sure legs and supports are perpendicular Figure 4).

x 8 90° Square Side Assembly End Supports Figure 4. End brackets attached.

4. Attach second side assembly to end supports with (8) M8-1.25 x 20 carriage bolts and (8) M8-1.25 flange nuts (see Figure 5).

Legs Figure 3. 1 of 2 side assemblies built.

2. Repeat Step 1 to build a second side assembly.

x 8 Second Side Assembly Figure 5. Second side assembly attached.

-2 T28170 Tool Stand (Mfd. Since 10/17)

5. Attach (4) foot brackets to inside of legs with (16) M8-1.25 x 20 carriage bolts and (16) M8-1.25 flange nuts (see with bottom of legs.

Figure 6). Make sure bottom of foot brackets are even Foot Brackets

Leveling Tool Stand

1. Place tool stand on flat surface.

2. Loosen (4) M12-1.75 hex nuts on tool stand feet. 3. Lay a level across tool stand from side-to side and end-to-end.

4. Adjust tool stand feet to make sure level lays flat at both positions.

5. Tighten hex nuts to secure tool stand feet.

Parts Breakdown & List

x 16 Figure 6. Foot brackets attached.

6. Thread (4) M12-1.75 hex nuts onto (4) adjust able feet (see Figure 7). 7. Thread (4) adjustable feet into foot brackets and secure with M12-1.75 flange nuts (see Figure 7).

4 5 x 4 x 4 Adjustable Foot Figure 7. Adjustable feet attached.

8. Turn tool stand upright.

3 2 1 7 6 8 12

T28170

9 9 11

NOTICE

DO NOT exceed maximum weight capacity of 400 lbs.

10

grizzly.com

REF PART #

1 2 3 4 5 6 7 8 9 10 11 12 PT28170001 PT28170002 PT28170003 PT28170004 PT28170005 PT28170006 PT28170007 PT28170008 PT28170009 PT28170010 PT28170011 PT28170012

DESCRIPTION

ADJUSTABLE FOOT M12-1.75 X 120 FOOT BRACKET LEG SIDE SUPPORT END SUPPORT CARRIAGE BOLT M8-1.25 X 20 FLANGE NUT M8-1.25

FLANGE NUT M12-1.75

HEX NUT M12-1.75

GRIZZLY.COM LABEL WEIGHT CAPACITY NOTICE LABEL QR CODE LABEL T28170 Tool Stand (Mfd. Since 10/17)

BUY PARTS ONLINE AT GRIZZLY.COM!

Scan QR code to visit our Parts Store.

-3-

-4 T28170 Tool Stand (Mfd. Since 10/17)