Grizzly W1847 Buffing System Owner Manual

Grizzly W1847 Buffing System Owner Manual
MODEL W1847
BUFFING SYSTEM
OWNER'S MANUAL
(FOR MODELS MANUFACTURED SINCE 9/17)
Phone: (360) 734-3482 • Online Technical Support: techsupport@woodstockint.com
COPYRIGHT © SEPTEMBER, 2017 BY WOODSTOCK INTERNATIONAL, INC.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT
THE WRITTEN APPROVAL OF WOODSTOCK INTERNATIONAL, INC.
#18918KB Printed in Taiwan
This manual provides critical safety instructions on the proper setup,
operation, maintenance, and service of this machine/tool. Save this
document, refer to it often, and use it to instruct other operators.
Failure to read, understand and follow the instructions in this manual
may result in fire or serious personal injury—including amputation,
electrocution, or death.
The owner of this machine/tool is solely responsible for its safe use.
This responsibility includes but is not limited to proper installation in
a safe environment, personnel training and usage authorization,
proper inspection and maintenance, manual availability and comprehension, application of safety devices, cutting/sanding/grinding tool
integrity, and the usage of personal protective equipment.
The manufacturer will not be held liable for injury or property
damage from negligence, improper training, machine modifications or
misuse.
Some dust created by power sanding, sawing, grinding, drilling, and
other construction activities contains chemicals known to the State of
California to cause cancer, birth defects or other reproductive harm.
Some examples of these chemicals are:
• Lead from lead-based paints.
• Crystalline silica from bricks, cement and other masonry products.
• Arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you
do this type of work. To reduce your exposure to these chemicals:
Work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter
out microscopic particles.
SAFETY.............................................................................................................5
Standard Machinery Safety Instructions................................................................. 5
Additional Safety for Buffing Systems................................................................... 7
MAINTENANCE.................................................................................................. 21
Schedule.................................................................................................... 21
Cleaning & Protecting.................................................................................... 21
Lubrication................................................................................................. 21
Troubleshooting........................................................................................... 22
Electrical Safety Instructions............................................................................ 23
Wiring Diagram............................................................................................ 24
SERVICE
PARTS............................................................................................................ 25
Main System................................................................................................ 25
Labels & Cosmetics....................................................................................... 26
MAINTENANCE
ACCESSORIES................................................................................................... 20
Buffing System Accessories.............................................................................. 20
OPERATIONS
OPERATIONS.................................................................................................... 14
General..................................................................................................... 14
Installing Buffing Wheels................................................................................. 15
Buffing Tips................................................................................................ 16
Buffing Compound Selection............................................................................ 17
Buffing Wheel Selection.................................................................................. 18
Loading Compound on Wheels.......................................................................... 19
SET UP
SETUP............................................................................................................ 10
Unpacking.................................................................................................. 10
Inventory................................................................................................... 10
Items Needed for Setup.................................................................................. 10
Machine Placement....................................................................................... 11
Cleaning Machine......................................................................................... 11
Bench Mounting........................................................................................... 12
Test Run..................................................................................................... 13
ELECTRICAL
ELECTRICAL.......................................................................................................8
Circuit Requirements....................................................................................... 8
Grounding Requirements................................................................................... 9
Extension Cords............................................................................................. 9
SAFETY
INTRODUCTION...................................................................................................2
Woodstock Technical Support............................................................................. 2
Machine Specifications..................................................................................... 3
Identification................................................................................................ 4
INTRODUCTION
Contents
WARRANTY...................................................................................................... 29
PARTS
USE THE QUICK GUIDE PAGE LABELS TO SEARCH OUT INFORMATION FAST!
INTRODUCTION
Model W1847 (For Machines Mfd. Since 9/17)
INTRODUCTION
Woodstock Technical Support
This machine has been specially designed to provide many years of trouble-free service. Close attention
to detail, ruggedly built parts and a rigid quality control program assure safe and reliable operation.
Woodstock International, Inc. is committed to customer satisfaction. Our intent with this manual is to
include the basic information for safety, setup, operation, maintenance, and service of this product.
We stand behind our machines! In the event that questions arise about your machine, please contact
Woodstock International Technical Support at (360) 734-3482 or send e-mail to: tech-support@shopfox.
biz. Our knowledgeable staff will help you troubleshoot problems and process warranty claims.
If you need the latest edition of this manual, you can download it from http://www.shopfox.biz.
If you have comments about this manual, please contact us at:
Woodstock International, Inc.
Attn: Technical Documentation Manager
P.O. Box 2309
Bellingham, WA 98227
Email: manuals@woodstockint.com
-2-
INTRODUCTION
Model W1847 (For Machines Mfd. Since 9/17)
MODEL W1847
Product Dimensions
BUFFING SYSTEM
Weight........................................................................................................... 53 lbs.
Width (side‐to‐side) x Depth (front‐to‐back) x Height.......................... 31‐1/4 x 7‐1/2 x 11‐1/2 in.
Footprint (Length x Width)................................................................................ 7 x 10 in.
Electrical
Power Requirement.............................................................................................. 115V
Full‐Load Current Rating......................................................................................... 14A
Minimum Circuit Size............................................................................................. 20A
Connection Type......................................................................................... Cord & Plug
Power Cord Included.............................................................................................. Yes
Power Cord Length............................................................................................... 6 ft.
Power Cord Gauge............................................................................................ 16 AWG
Plug Included....................................................................................................... Yes
Included Plug Type........................................................................................ NEMA 5‐15
Switch Type.............................................................................. Push / Pull Power Switch
Motors
Main
Horsepower................................................................................................. 1 HP
Phase.............................................................................................. Single‐Phase
Amps.......................................................................................................... 14A
Speed.................................................................................................. 3450 RPM
Type......................................................................... TEFC Capacitor‐Start Induction
Power Transfer ................................................................................... Direct Drive
Bearings............................................................... Shielded & Permanently Lubricated
Main Specifications
Operation Info
Buffer Type....................................................................................... Bench Model
Maximum Wheel Diameter.............................................................................. 12 in.
Wheel Bore.............................................................................................. 5/8 in.
Other
Country of Origin ............................................................................................. Taiwan
Warranty ....................................................................................................... 2 Years
Approximate Assembly & Setup Time .................................................................... 15 min.
Serial Number Location .......................................................................... Machine ID Label
ISO 9001 Factory .................................................................................................. Yes
Model W1847 Machine Specifications, Page 1 of 2
-3-
INTRODUCTION
Model W1847 (For Machines Mfd. Since 9/17)
Identification
Become familiar with the names and locations of the controls and features shown below to better
understand the instructions in this manual.
A
D
E
F
C
C
B
G
D
B
H
A.
B.
C.
D.
E.
F.
G.
H.
Buffing Wheel Hex Nut (LH)
Buffing Wheel Flange (2 each)
T-Bushing 3⁄4"
T-Bushing 1"
Buffing Wheel Shaft
Buffing Wheel Hex Nut (RH)
Motor
ON­/OFF Switch
To. reduce. your. risk. of. serious. injury.
or. damage. to. the. machine,. read. this.
entire.manual.BEFORE.using.machine.
-4-
Model W1847 (For Machines Mfd. Since 9/17)
SAFETY
The. purpose. of. safety. symbols. is. to. attract. your. attention. to. possible. hazardous. conditions.. This.
manual.uses.a.series.of.symbols.and.signal.words.intended.to.convey.the.level.of.importance.of.the.
safety.messages..The.progression.of.symbols.is.described.below..Remember.that.safety.messages.by.
themselves. do. not. eliminate. danger. and. are. not. a. substitute. for. proper. accident. prevention. measures—this.responsibility.is.ultimately.up.to.the.operator!
Indicates.an.imminently.hazardous.situation.which,.if.not.avoided,.
WILL.result.in.death.or.serious.injury.
Indicates.a.potentially.hazardous.situation.which,.if.not.avoided,.
COULD.result.in.death.or.serious.injury.
Indicates.a.potentially.hazardous.situation.which,.if.not.avoided,.
MAY.result.in.minor.or.moderate.injury.
NOTICE
This.symbol.is.used.to.alert.the.user.to.useful.information.about.
proper.operation.of.the.equipment.or.a.situation.that.may.cause.
damage.to.the.machinery.
Standard
Machinery Safety Instructions
Standard.Machinery.Safety.Instructions
OWNER’S.MANUAL..Read and understand this
owner’s manual BEFORE using machine.
ELECTRICAL.EQUIPMENT.INJURY.RISKS..You can
be shocked, burned, or killed by touching live
electrical components or improperly grounded
machinery. To reduce this risk, only allow an
electrician or qualified service personnel to
do electrical installation or repair work, and
always disconnect power before accessing or
exposing electrical equipment.
TRAINED.OPERATORS.ONLY..Untrained operators
have a higher risk of being hurt or killed. Only
allow trained/supervised people to use this
machine. When machine is not being used,
disconnect power, remove switch keys, or
lock-out machine to prevent unauthorized
use—especially around children. Make
workshop kid proof!
DISCONNECT.POWER.FIRST..Always disconnect
machine from power supply BEFORE making
adjustments, changing tooling, or servicing
machine. This eliminates the risk of injury
from unintended startup or contact with live
electrical components.
DANGEROUS.ENVIRONMENTS..Do not use
machinery in areas that are wet, cluttered,
or have poor lighting. Operating machinery
in these areas greatly increases the risk of
accidents and injury.
EYE.PROTECTION..Always wear ANSI-approved
safety glasses or a face shield when operating
or observing machinery to reduce the risk of
eye injury or blindness from flying particles.
Everyday eyeglasses are not approved safety
glasses.
MENTAL.ALERTNESS.REQUIRED..Full mental
alertness is required for safe operation of
machinery. Never operate under the influence
of drugs or alcohol, when tired, or when
distracted.
-5-
SAFETY
For.Your.Own.Safety,
Read.Manual.Before.Operating.Machine
SAFETY
Model W1847 (For Machines Mfd. Since 9/17)
WEARING.PROPER.APPAREL..Do not wear
clothing, apparel, or jewelry that can become
entangled in moving parts. Always tie back
or cover long hair. Wear non-slip footwear to
avoid accidental slips, which could cause loss
of workpiece control.
FORCING.MACHINERY..Do not force machine. It
will do the job safer and better at the rate for
which it was designed.
NEVER.STAND.ON.MACHINE..Serious injury may
occur if machine is tipped or if the cutting
tool is unintentionally contacted.
HAZARDOUS.DUST..Dust created while using
machinery may cause cancer, birth defects,
or long-term respiratory damage. Be aware of
dust hazards associated with each workpiece
material, and always wear a NIOSH-approved
respirator to reduce your risk.
STABLE.MACHINE..Unexpected movement during
operation greatly increases risk of injury or
loss of control. Before starting, verify machine
is stable and mobile base (if used) is locked.
USE.RECOMMENDED.ACCESSORIES..Consult
this owner’s manual or the manufacturer for
recommended accessories. Using improper
accessories will increase risk of serious injury.
HEARING.PROTECTION..Always wear hearing
protection when operating or observing
loud machinery. Extended exposure to this
noise without hearing protection can cause
permanent hearing loss.
UNATTENDED.OPERATION..To reduce the risk
of accidental injury, turn machine OFF and
ensure all moving parts completely stop
before walking away. Never leave machine
running while unattended.
REMOVE.ADJUSTING.TOOLS..Tools left on
machinery can become dangerous projectiles
upon startup. Never leave chuck keys,
wrenches, or any other tools on machine.
Always verify removal before starting!
MAINTAIN.WITH.CARE..Follow all maintenance
instructions and lubrication schedules to
keep machine in good working condition. A
machine that is improperly maintained could
malfunction, leading to serious personal injury
or death.
INTENDED.USAGE..Only use machine for its
intended purpose—never make modifications
without prior approval from Woodstock
International. Modifying machine or using
it differently than intended will void the
warranty and may result in malfunction or
mechanical failure that leads to serious
personal injury or death!
CHECK.DAMAGED.PARTS..Regularly inspect
machine for any condition that may affect
safe operation. Immediately repair or replace
damaged or mis-adjusted parts before
operating machine.
AWKWARD.POSITIONS..Keep proper footing and
balance at all times when operating machine.
Do not overreach! Avoid awkward hand
positions that make workpiece control difficult
or increase the risk of accidental injury.
CHILDREN.&.BYSTANDERS..Keep children and
bystanders at a safe distance from the work
area. Stop using machine if they become a
distraction.
MAINTAIN.POWER.CORDS..When disconnecting
cord-connected machines from power, grab
and pull the plug—NOT the cord. Pulling the
cord may damage the wires inside, resulting
in a short. Do not handle cord/plug with wet
hands. Avoid cord damage by keeping it away
from heated surfaces, high traffic areas, harsh
chemicals, and wet/damp locations.
GUARDS.&.COVERS..Guards and covers reduce
accidental contact with moving parts or flying
debris—make sure they are properly installed,
undamaged, and working correctly.
EXPERIENCING.DIFFICULTIES..If at any time
you experience difficulties performing the
intended operation, stop using the machine!
Contact Technical Support at (360) 734-3482.
-6-
Model W1847 (For Machines Mfd. Since 9/17)
Additional Safety for Buffing Systems
WORKPIECE CONTROL. If you cannot hold small
workpieces securely, do not buff them with
this machine. Secure them with clamps or
similar jigs or use a smaller buffer.
HAND/WHEEL CONTACT. Never purposely touch
the moving buffing wheel or shaft. Take care
to keep fingers away from buffing wheel
during operations. If the workpiece is small
or difficult to hold, use a workpiece holding
fixture. Abrasive accessories can quickly
remove large amounts of skin!
DISCONNECT POWER WHEN SERVICING.
Disconnect the machine from power and
allow the wheel to come to a complete stop
before service, maintenance, or adjustments.
Avoid pulling cord-connected machinery
from the cord—instead, grasp the plug when
disconnecting it from power.
AVOID WORKPIECE GRAB. Firmly support the
workpiece against the rotation direction of
the buffing wheel. Otherwise, the buffing
wheel could grab the workpiece and pull your
hands into the moving wheel.
AVOID ENTANGLEMENT. Tie back long hair and
remove any loose-fitting clothing or jewelry
that could be caught up in the buffing wheel
or other moving machine parts. Avoid wearing
gloves as they may get caught in the buffing
wheel and cause entanglement injuries.
AVOID KICKBACK. Avoid kickback by buffing in
accordance with directional arrows. Always
buff on the downward side of the wheel—pay
close attention to the direction of wheel
rotation to avoid placing the workpiece
against the upward side of the buffing wheel.
Avoid buffing with excessive force.
MOUNTING TO BENCH/STAND. An unsecured
buffer may become dangerously out of control
during operation. Make sure buffer is FIRMLY
secured to a bench/stand before use.
WORKPIECE SELECTION. Always inspect the
condition of your workpiece. DO NOT buff
pieces with loose knots, large splinters, sharp
edges, and DO NOT buff knives, cable, chain
or other potentially dangerous objects that
may be grabbed by the buffing wheel and
thrown at the operator.
CORRECT ACCESSORIES AND USE. Never install
a grinding wheel on this buffer. It is only
designed for buffing and polishing. Never
exceed the maximum speed listed on each
buffing/polishing wheel.
WORKPIECE FEED. Allow the wheel to reach
full speed, then slowly ease the workpiece
into the buffing wheel, holding it in front
of and slightly below the wheel center. Do
not place the workpiece on the top or sides
of the buffing wheel and do not place an
edge or corner of the workpiece against the
buffing wheel, or jam it against the wheel.
The workpiece may eject toward the operator
or be torn from the operator's hands, causing
serious personal injury.
OPERATOR POSITION. Do not stand directly in
front of the buffer wheel when turning the
machine on, or when buffing. Do not buff
material at the rear of the machine.
BE AWARE OF DUST ALLERGIES. Be aware that
certain woods may cause an allergic reaction
in people and animals, especially when fine
dust is created by buffing . Make sure you
know what type of wood dust you will be
exposed to in case there is a possibility of an
allergic reaction.
-7-
SAFETY
Serious injury or death can occur from impact injuries. Rotating buffing wheels can easily remove
skin, or entanglement/amputation injuries can occur from being caught in moving parts or
in-running pinch points. To minimize risk of getting hurt or killed, anyone operating machine MUST
completely heed hazards and warnings below.
Model W1847 (For Machines Mfd. Since 9/17)
ELECTRICAL
Circuit Requirements
ELECTRICAL
This machine must be connected to the correct size and
type of power supply circuit, or fire or electrical damage
may occur. Read through this section to determine if an
adequate power supply circuit is available. If a correct
circuit is not available, a qualified electrician MUST install
one before you can connect the machine to power.
A power supply circuit includes all electrical equipment
between the breaker box or fuse panel in the building
and the machine. The power supply circuit used for
this machine must be sized to safely handle the fullload current drawn from the machine for an extended
period of time. (If this machine is connected to a circuit
protected by fuses, use a time delay fuse marked D.)
The. machine. must. be. properly. set. up.
before. it. is. safe. to. operate.. DO. NOT.
connect. this. machine. to. the. power.
source.until.instructed.to.do.so.later.in.
this.manual.
Full-Load Current Rating
The full-load current rating is the amperage a machine
draws at 100% of the rated output power. On machines
with multiple motors, this is the amperage drawn by the
largest motor or sum of all motors and electrical devices
that might operate at one time during normal operations.
Full-Load Current Rating at 115V................... 14 Amps
Circuit Requirements for 115V
This machine is prewired to operate on a power supply
circuit that has a verified ground and meets the following
requirements:
Circuit Type........110V, 115V, 120V, 60 Hz, Single-Phase
Circuit Size.............................................. 20 Amps
Plug/Receptacle..................................... NEMA 5-15
-8-
Incorrectly. wiring. or. grounding. this.
machine.can.cause.electrocution,.fire,.
or.machine.damage..To.reduce.this.risk,.
only.an.electrician.or.qualified.service.
personnel. should. do. any. required.
electrical.work.on.this.machine.
NOTICE
The. circuit. requirements. listed. in. this.
manual. apply. to. a. dedicated. circuit—
where.only.one.machine.will.be.running.
at. a. time.. If. this. machine. will. be.
connected. to. a. shared. circuit. where.
multiple.machines.will.be.running.at.the.
same.time,.consult.with.an.electrician.
to. ensure. that. the. circuit. is. properly.
sized.for.safe.operation.
Model W1847 (For Machines Mfd. Since 9/17)
Grounding Requirements
This machine MUST be grounded. In the event of certain
types of malfunctions or breakdowns, grounding provides
a path of least resistance for electric current to travel—in
order to reduce the risk of electric shock.
Check with a qualified electrician or service personnel
if you do not understand these grounding requirements,
or if you are in doubt about whether the tool is
properly grounded. If you ever notice that a cord or
plug is damaged or worn, disconnect it from power, and
immediately replace it with a new one.
GROUNDED
5-15 RECEPTACLE
Grounding Prong
5-15 PLUG
Neutral Hot
Figure 1. NEMA 5-15 plug & receptacle.
For 115V Connection
This machine is equipped with a power cord with an
equipment-grounding wire and NEMA 5-15 grounding
plug (see figure). The plug must only be inserted into
a matching receptacle that is properly installed and
grounded in accordance with local codes and ordinances.
Extension Cords
We do not recommend using an extension cord with
this machine. Extension cords cause voltage drop, which
may damage electrical components and shorten motor
life. Voltage drop increases with longer extension cords
and smaller gauge sizes (higher gauge numbers indicate
smaller sizes).
Any extension cord used with this machine must contain a
ground wire, match the required plug and receptacle, and
meet the following requirements:
Minimum Gauge Size at 110V....................... 14 AWG
Maximum Length (Shorter is Better).................50 ft.
-9-
DO. NOT. modify. the. provided. plug. or.
use. an. adapter. if. the. plug. will. not.
fit. the. receptacle.. Instead,. have. an.
electrician.install.the.proper.receptacle.
on. a. power. supply. circuit. that. meets.
the.requirements.for.this.machine.
ELECTRICAL
Improper connection of the equipment-grounding wire will
increase the risk of electric shock. The wire with green
insulation (with/without yellow stripes) is the equipmentgrounding wire. If repair or replacement of the power
cord or plug is necessary, do not connect the equipmentgrounding wire to a live (current carrying) terminal.
115V
Model W1847 (For Machines Mfd. Since 9/17)
SETUP
Unpacking
This machine has been carefully packaged for safe
transportation. If you notice the machine has been
damaged during shipping, please contact your authorized
Shop Fox dealer immediately.
Inventory
SETUP
The following is a list of items shipped with your machine.
Before beginning setup, lay these items out and inventory
them.
Note: If you cannot find an item on this list, carefully
check around/inside the machine and packaging materials.
Often, these items get lost in packaging materials while
unpacking or they are pre-installed at the factory.
Box Inventory (Figure 2)
Qty
A. Wheel Flanges 5⁄8" Bore...................................4
B. Hex Nuts 5⁄8-11 (1 LH, 1 RH).............................2
C. T-Bushings 3⁄4" x 5⁄8" x 5⁄16"...............................2
D. T-Bushings 1" x 3⁄4" x 3⁄8"..................................2
E. W1847 Buffer (Not Shown)................................1
Items Needed for Setup
Keep. machine. disconnected. from.
power.until.instructed.otherwise.
A
B
C
D
Figure 2. Buffing system inventory.
The following items are needed, but not included, to set
up your machine.
Description Qty
• Safety Glasses...............................................1
• Wrenches 15⁄16"..............................................2
-10-
SUFFOCATION HAZARD!
Immediately discard all
plastic bags and packing
materials to eliminate
choking/suffocation
hazards for children and
animals.
Model W1847 (For Machines Mfd. Since 9/17)
Machine Placement
Cleaning Machine
Workbench Load
The unpainted surfaces of your machine are
coated with a heavy-duty rust preventative that
prevents corrosion during shipment and storage.
This rust preventative works extremely well, but
it will take a little time to clean.
Refer to the Machine.Specifications for the
weight and footprint specifications of your
machine. Some workbenches may require
additional reinforcement to support the weight
of the machine and workpiece materials.
Be patient and do a thorough job cleaning your
machine. The time you spend doing this now will
give you a better appreciation for the proper
care of your machine's unpainted surfaces.
Placement Location
Consider anticipated workpiece sizes and
additional space needed for auxiliary stands,
work tables, or other machinery when
establishing a location for this machine in the
shop. Below is the minimum amount of space
needed for the machine.
There are many ways to remove this rust
preventative, but the following steps work well
in a wide variety of situations. Always follow the
manufacturer’s instructions with any cleaning
product you use and make sure you work in a
well-ventilated area to minimize exposure to
toxic fumes.
7½"
10"
Basic.steps.for.removing.rust.preventative:
Figure 3. Minimum working clearances.
INJURY.HAZARD!.Untrained.
users.can.injure.themselves.
with.this.machine..Restrict.
access. to. machine. when.
you. are. away,. especially. if.
it. is. installed. where. children.are.present.
USE.this.and.other.machinery.with.caution.
and. respect.. Always. consider. safety. first,.
as. it. applies. to. your. individual. working.
conditions.. No. list. of. safety. guidelines. can.
be. complete—every. shop. environment. is.
different..Failure.to.follow.guidelines.could.
result.in.serious.personal.injury,.damage.to.
equipment.or.poor.work.results.
1.
Put on safety glasses.
2.
Coat the rust preventative with a liberal
amount of cleaner/degreaser, then let it
soak for 5–10 minutes.
3.
Wipe off the surfaces. If your cleaner/
degreaser is effective, the rust
preventative will wipe off easily. If you
have a plastic paint scraper, scrape off as
much as you can first, then wipe off the
rest with the rag.
4.
Repeat Steps.2–3 as necessary until clean,
then coat all unpainted surfaces with a
quality metal protectant to prevent rust.
Avoid. chlorine-based. solvents,. such. as.
acetone. or. brake. parts. cleaner,. that. may.
damage.painted.surfaces..
-11-
SETUP
Before.cleaning,.gather.the.following:
• Disposable rags
• Cleaner/degreaser (WD•40 works well)
• Safety glasses & disposable gloves
• Plastic paint scraper (optional)
311/4"
Model W1847 (For Machines Mfd. Since 9/17)
Bench Mounting
Number of Mounting Holes................................... 4
Diameter of Mounting Hardware Needed..............7⁄16"
The base of this machine has mounting holes that allow it
to be fastened to a workbench or other mounting surface
to prevent it from moving during operation and causing
accidental injury or damage.
The strongest mounting option is a “Through Mount” (see
example) where holes are drilled all the way through the
workbench—and hex bolts, washers, and hex nuts are
used to secure the machine in place.
Bolt
Flat Washer
Machine Base
Workbench
Flat Washer
Lock Washer
Hex Nut
SETUP
Figure 4. Typical "Through Mount" setup.
Another option is a “Direct Mount” (see example) where
the machine is secured directly to the workbench with lag
screws and washers.
Lag Screw
Flat Washer
Machine Base
Workbench
Figure 5. Typical "Direct Mount" setup.
-12-
Model W1847 (For Machines Mfd. Since 9/17)
Test Run
Once assembly is complete, test run the machine to
ensure it is properly connected to power and safety
components are functioning properly.
If you find an unusual problem during the test run,
immediately stop the machine, disconnect it from power,
and fix the problem BEFORE operating the machine again.
The Troubleshooting table in the SERVICE section of this
manual can help.
Serious. injury. or. death. can. result.
from. using. this. machine. BEFORE.
understanding. its. controls. and. related.
safety.information..DO.NOT.operate,.or.
allow.others.to.operate,.machine.until.
the.information.is.understood..
To test run machine, do these steps:
Clear all setup tools away from machine.
2.
Connect machine to power supply.
3.
Turn machine ON by pulling power button out. Verify
motor operation, and then turn machine OFF by
pushing button in.
DO. NOT. start. machine. until. all.
preceding.setup.instructions.have.been.
performed..Operating.an.improperly.set.
up. machine. may. result. in. malfunction.
or. unexpected. results. that. can. lead.
to. serious. injury,. death,. or. machine/
property.damage.
The motor should run smoothly and without unusual
problems or noises.
READ and understand this entire
manual before using this machine.
Serious personal injury may occur if
safety and operational information is
not understood and followed. DO NOT
risk your safety by not reading!
-13-
SETUP
1.
Model W1847 (For Machines Mfd. Since 9/17)
OPERATIONS
General
This machine will perform many types of operations
that are beyond the scope of this manual. Many of these
operations can be dangerous or deadly if performed
incorrectly.
The instructions in this section are written with the
understanding that the operator has the necessary
knowledge and skills to operate this machine. If at any
time you are experiencing difficulties performing any
operation, stop using the machine!
To. reduce. your. risk. of. serious. injury.
or. damage. to. the. machine,. read. this.
entire.manual.BEFORE.using.machine.
The overview below provides the novice machine operator
with a basic understanding of how the machine is used
during operation, so the machine controls/components
discussed later in this manual are easier to understand.
Due to its generic nature, this overview is NOT intended
to be an instructional guide.
OPERATIONS
To complete a typical operation, the operator does the
following:
1.
Examines workpiece to make sure it is suitable for
buffing.
2.
Selects correct wheel for type of operation, then
inspects installs wheel.
3.
Ensures that ON/OFF switch is in OFF position, and
connects buffer to power.
4.
Ties back loose hair and clothing, and puts on
personal protective equipment.
5.
Stands aside, starts buffer, and allows it to reach full
speed and operate for at least one minute to ensure
buffing wheel does not fly apart from centrifugal
force of rotation.
6.
Using both hands to firmly hold workpiece, operator
gradually feeds workpiece into wheel and continually
moves workpiece left and right.
7.
Stops buffer after buffing operation is complete.
-14-
To. reduce. the. risk. of. eye. injury. and.
long-term. respiratory. damage,. always.
wear. a. face. shield,. safety. glasses,.
and. a. respirator. while. operating. this.
machine.
The Model W1847 Buffing System is
strictly designed for buffing and sanding
operations. IT IS NOT A GRINDER. The
absence of grinding wheel guards and
eye shields prohibits the use of this
machine as a grinder.
If you are an inexperienced operator,
we strongly recommend that you read
books or trade articles, or seek training
from an experienced operator of this
type of machinery before performing
unfamiliar operations. Above.all,.safety.
must.come.first!
Model W1847 (For Machines Mfd. Since 9/17)
Installing Buffing Wheels
This buffer has left and right shafts to provide the option
of mounting different types of wheels on each side, or
mounting a buffing wheel on one side and a sanding drum
(not included) on the other..
Tools Needed
Qty
⁄16" Wrenches...................................................2
15
To. reduce. your. risk. of. serious. injury.
or. damage. to. the. machine,. read. this.
entire.manual.BEFORE.using.machine.
To install buffing wheels, do these steps:
1.
DISCONNECT MACHINE FROM POWER!
2.
Remove hex nut and outer flange from each shaft.
DO NOT remove inner flange or T-bushings.
When facing the machine, the shaft on the left
side has left-handed threads, meaning the hex nut
loosens when turned clockwise. The shaft on the
right side has right-handed threads, meaning the hex
nut loosens when turned counterclockwise.
Install buffing wheel (not included) between inner
and outer wheel flanges. Secure with hex nut
removed in Step 2, as shown in Figure 6.
Outer
Flange
Inner
Flange
Hex Nut
CORRECT
Buffing
Wheel
T-Bushings (2)
Figure 6. Buffing wheel installed.
-15-
OPERATIONS
3.
To. reduce. the. risk. of. eye. injury. and.
long-term. respiratory. damage,. always.
wear. a. face. shield,. safety. glasses,.
and. a. respirator. while. operating. this.
machine.
Model W1847 (For Machines Mfd. Since 9/17)
Buffing Tips
Buffing operations on your buffer will vary depending on
the type of material to be buffed, the type of buffing
wheel used, and the finished result you need. Below are
some quick tips for getting the most out of your buffer.
•
Apply buffing compounds in small amounts at a
time. Apply paste-type compounds with a wand or
directly to the part. For wax-based polishing sticktype compounds, only press the compound on the
wheel for a couple of seconds while the machine is
running. Avoid using too much compound!
•
DO NOT mix two different compounds on the same
wheel. For best results, use a separate wheel for
each compound.
•
Put your workpiece under the wheel when you
are loading the compound on the buffing wheel.
This way, you will catch any compound that would
normally be wasted on the floor.
•
Only use the area indicated in Figure 7 to do the
actual buffing. Contacting the workpiece on areas
outside the correct area may flip the workpiece out
of your hands.
•
Hold the workpiece tightly with both hands at all
times while buffing. Placing one hand near the
contact point will give you better control.
•
•
Keep buffing wheels raked out before each use and
when buildup gets heavy during use. Raking means
to clean the buffing wheels with a wheel rake (see
Page 21) to remove built-up compounds and metal
particles. ALWAYS use light pressure when raking
wheels!
Always use an upward stroke with heavy to moderate
pressure for cutting. Use a downward stroke with
light pressure for polishing (see Figure 8).
-16-
Never buff with workpiece on top of
the wheel. Workpiece may catch on
wheel and be thrown at operator.
Always buff workpiece near the bottom of the wheel!
FRONT
on
a ti
ot
TOP
(Right Front
Side View)
Only Contact
Workpiece Here
BOTTOM
Figure 7. Location where workpiece
should contact wheel.
(Right Front Side View)
Polishing
Stroke
(Downward)
Cutting
Stroke
(Upward)
Whee
lR
o
Wear safety equipment when buffing. If the buffer
forces the workpiece out of your hand, be prepared
for it to come flying at you! Wear safety glasses or
a face shield and a heavy leather apron. Also, wear
a dust mask to protect your lungs from microscopic
particulate that will be flying off the wheel.
tion
ta
Contact
Area
Whee
lR
o
•
To. reduce. the. risk. of. eye. injury. and.
long-term. respiratory. damage,. always.
wear. a. face. shield,. safety. glasses,.
and. a. respirator. while. operating. this.
machine.
el
R
Thoroughly clean all parts that you plan to buff.
Dirt, oil, rust, paint, or other film must be removed
chemically or with water. Dry parts with a clean rag.
Whe
OPERATIONS
•
tion
ta
Contact
Area
Figure 8. Cutting and polishing strokes.
Model W1847 (For Machines Mfd. Since 9/17)
Buffing Compound
Selection
Most colors of abrasives have similar applications, but
always check with the manufacturer of your particular
compound.
Shop Fox offers the following compounds:
Red Rouge — Made for fine polishing on brass and gold.
Provides an excellent shine when used with a loose muslin
buffing wheel.
Only apply compound to moving wheel
for a couple seconds to avoid placing
too much compound on the buffing
wheel.
Use caution when polishing plated
metals; there is a chance that the thin
plated material may be damaged. A
light pressure is all that is needed for
quality work.
Green (Extra Fine) — Great for extra-fine polishing on
most metals to bring out that mirror finish. Works best
with loose muslin and spiral-sewn buffing wheels.
White — Great for ivory, plastic, and resins when used
successively with the soft spiral sewn and soft airway
buffing wheels.
Black — Designed to be used with sisal and airway hard
buffing wheels. This compound is perfect for the initial
rough cut on stainless steel and iron.
OPERATIONS
Tripoli — A true middle-of-the-road abrasive, Tripoli
provides an excellent medium cut for brass, aluminum,
and zinc alloy.
Green (Fine) — Slightly more abrasive than the extra fine
green, this green compound is great for a medium to fine
polish with most softer metals.
Buffing Compound Sequence Key
R: Rough
F: Final Cut, Initial Polish
P: Final Polish
: Do Not Use
Compound Type
Tripoli
Red Rouge
White Rouge
Black Rouge
Plastics,
Soft
Metals
R
X
F
P R
X
X
Thin
Plating,
Gold,
Silver
F
P
X
Chrome
&
Nickel
Plate
R
F
X
Copper,
Brass,
Aluminum
P
X
R
X
F
P
X
X
Iron,
Steel,
Stainless
Steel
R
F
P
X
X
X
-17-
Figure 9. Applying green (extra fine)
buffing compound to wheel.
Model W1847 (For Machines Mfd. Since 9/17)
Buffing Wheel Selection
Buffing wheels are available for most types of metals
and for different stages in the buffing process. Below are
pictures and descriptions of common wheel types:
Buffing Wheel Sequence Key
R: Rough
F: Final Cut, Initial Polish
P: Final Polish
: Do Not Use
Buffing Wheel Style
Loose Muslin-Soft
Loose Muslin-Hard
Airway Hard
Airway Soft
Laminated Sisal
Spiral Sewn
Plastics,
Soft
Metals
R
F
P R
X
Thin
Plating,
Gold,
Silver
F
P
X
Chrome
Plate,
Nickel
Plate
R
F
P
X
Copper,
Brass,
Aluminum
Iron,
Steel,
Stainless
Steel
R
R
F P
X
X
X
F
P
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Laminated Sisal
Designed for rough
cutting, sisal works
well with various
steels, copper, aluminum, and brass
to remove scratches and prepare the
piece for polishing.
Airway Hard
Made of 100% cotton sheets
that are treated to stiffen the
material. Pleats in the material help hold compound. These
are great for rough cutting
plastics and initial polishing a
wide variety of metals.
OPERATIONS
Loose Muslin
Soft feather-edged
muslin stitched
together near the
center leaves the
outer edge to provide a wide angle,
fine polishing surface. Perfect for
polishing stainless
steel, chrome,
gold, or silver.
Spiral Sewn
Consist of layers of
100% unbleached
cotton sheeting
that are spiral
sewn 1⁄8" apart.
Works well for initial polish on brass,
stainless steel, aluminum, bronze,
and cast iron.
Airway Soft
Made of 100% cotton sheets
and held together with a steel
retainer. Pleats in the material
help hold compound. These
wheels are great for polishing
soft metals and plastics.
-18-
Model W1847 (For Machines Mfd. Since 9/17)
Loading Compound on
Wheels
Select a buffing compound and buffing wheel that
is suitable for the workpiece and each sequence of
the buffing or polishing operation. Refer to Buffing
Compound Selection on Page 17 and Buffing Wheel
Selection on Page 18 before loading compound on the
buffing wheel.
Tools Needed
Qty
15
⁄16" Wrench......................................................1
To load compound on wheels, do these steps:
2.
Select buffing compound suitable to material
(refer to Buffing Compound Selection and Buffing
Compound Sequence Key on Page 17).
Note: Make sure buffing wheel is free of any
compound used in prior buffing operation. Clean
with a buffing wheel rake if necessary (Page 21).
3.
Put on safety glasses, face shield, and respirator,
then connect machine to power.
4.
Stand to side of buffer wheel and turn machine ON.
Allow buffer wheel to reach full speed.
5.
Apply buffing compound to rotating face of wheel,
as shown in Figures 10-11. Only hold compound to
wheel for 2 – 5 seconds. The buffer is now ready for
buffing/polishing.
6.
Turn machine OFF when completed.
Figure 10. Applying buffing compound to
wheel.
FRONT
el
R
Select buffing wheel suitable for workpiece (refer
to Buffing Wheel Selection and Buffing Wheel
Sequence Key on Page 18). Follow directions on
Page 15 to install wheel.
on
a ti
ot
TOP
Whe
1.
(Right Front
Side View)
Only Contact
Workpiece Here
BOTTOM
-19-
SERVICE
Figure 11. Location where workpiece
should contact wheel.
Model W1847 (For Machines Mfd. Since 9/17)
ACCESSORIES
Buffing System Accessories
The following Buffing System accessories may be available through your local Woodstock International
Inc. Dealer. If you do not have a dealer in your area, these products are also available through online
dealers. Please call or e-mail Woodstock International Inc. Customer Service to get a current listing of
dealers at: 1-800-840-8420 or at sales@woodstockint.com.
D3302—Buffing System Stand
D3303—Buffing System Stand
The D3302 and D3303 buffing system stands are two of the most
stable stands on the market. The D3302 features a rectangular column
and base and stands 39" tall. The D3303 features a round column with
triangular base and stands 32 1⁄2" high. Both models have adjustable
rubber feet.
D3302
D3303
OPERATIONS
D2901, D2902, D2903, D2904, D2905, D2912—Buffing Compounds
D2901 Red Rouge, D2902 Green (Extra Fine), D2903 White, D2904
Black Emery Cake, D2905 Tripoli Brown Rouge, and D2912 Green
(Fine) buffing compounds are each available in 1-lb. bars. Due to their
nature, colors may vary.
Buffing Wheels
MODEL
TYPE
SIZE
MAX RPM
D3188
Soft Muslin
5" x 40 Ply x ⁄8"
5,000
D3191
Hard Muslin
6" x 50 Ply x 5⁄8"
4,000
D3194
Soft Airway
6" x 12 Ply x ⁄8" Hole
3,500
D3193
Hard Airway
6" x 12 Ply x ⁄8" Hole
3,500
D3176
Spiral Sewn
4" x 40 Ply x 5⁄8"
5,000
D3181
Spiral Sewn
6" x 40 Ply x 5⁄8"
4,000
D2523
Sisal
8" x ⁄2" Ply x ⁄8"
5
5
5
1
D3194
D3193
D3188
D3191
5
-20-
Model W1847 (For Machines Mfd. Since 9/17)
MAINTENANCE
Schedule
For optimum performance and safe operation, follow this
schedule and fix any of these conditions immediately after
discovery. Do not continue using machine until it is fixed.
Daily Check:
• Loose bolts on shafts or mounted base.
• Damaged buffing wheels.
• Damaged or worn sanding paper.
• Sanding drum air pressure.
• Worn or damaged wires.
• Any other unsafe condition.
MAKE. SURE. that. your. machine. is.
unplugged. during. all. maintenance.
procedures!. If. this. warning. is. ignored,.
serious.personal.injury.may.occur.
Weekly/Monthly Check:
• Worn or damaged shaft bearings.
• Worn or damaged cord.
• Worn switch.
Cleaning & Protecting
Cleaning the Model W1847 Buffing System is relatively
easy. Vacuum excess wood chips, sawdust, or metal shavings and wipe off the remaining dust with a dry cloth.
Wipe down shafts with a non-staining lubricant after
cleaning.
Lubrication
The bearings inside the model W1847 are sealed and
permanently lubricated. Simply leave them alone unless
they need replacing.
-21-
Figure 12. Removing compound from
buffing wheel with buffing wheel rake.
MAINTENANCE
To clean buffing wheels, use a buffing wheel rake to
remove dried compound. Guide the rake across the
spinning buffing wheel using light pressure as shown in
Figure 12.
Model W1847 (For Machines Mfd. Since 9/17)
Troubleshooting
The following troubleshooting tables cover common problems that may occur with this machine. If you
need replacement parts or additional troubleshooting help, contact our Technical Support.
Note: Before contacting Tech Support, find the machine serial number, manufacture date, and
original purchase receipt (if available). This information is required to properly assist you.
Motor and Electrical
PROBLEM
POSSIBLE CAUSE
CORRECTIVE ACTION
Machine does not 1. Power supply circuit breaker tripped or fuse
start, or power
blown.
supply breaker
2. Start capacitor at fault.
immediately trips
3. Centrifugal switch at fault.
after startup.
4. Wiring open/has high resistance.
5. ON/OFF switch at fault.
6. Motor at fault.
Machine stalls or
underpowered.
1. Buffing wheel too large/wide or exceeds
recommended wheel rating.
2. Motor overheated, tripping machine circuit
breaker.
3. Motor connection is wired incorrectly.
4. Motor bearings at fault.
5. Motor is at fault.
Machine has
1. Buffing wheel has become loose, worn, or
vibration or noisy
components (steel center hub) are
operation.
dislodged.
2. Motor or component loose.
3. Incorrectly mounted to workbench.
4. Motor bearings at fault.
5. Motor shaft bent.
1. Ensure circuit is sized correctly and free of shorts.
Reset circuit breaker or replace fuse.
2. Test/replace.
3. Adjust/replace centrifugal switch if available.
4. Check/fix broken, disconnected, or corroded
wires.
5. Replace ON/OFF switch.
6. Test/repair/replace.
1. Replace with smaller wheel or reduce wheel
width.
2. Clean motor/let cool, and reduce workload. Reset
breaker.
3. Correct motor wiring connections.
4. Test/repair/replace.
5. Test/repair/replace.
1. Replace buffing wheel.
2. Inspect/replace damaged bolts/nuts, and retighten with thread-locking fluid.
3. Shim or tighten mounting hardware.
4. Test by rotating shaft; rotational grinding/loose
shaft requires bearing replacement.
5. Test with dial indicator and replace motor.
SERVICE
Buffing Operations
PROBLEM
POSSIBLE CAUSE
CORRECTIVE ACTION
Poor results from
buffing/polishing
operation.
1. Workpiece contains residue or contaminants.
1. Dirt, oil, rust, paint, or other film must be
removed chemically or with water. Dry parts
before buffing.
2. Use upward stroke with heavy to moderate pressure for cutting; use downward stroke with light
pressure for polishing (Page 16).
3. DO NOT mix different compounds on same wheel.
Use separate wheel for each compound. Remove
compound with buffing wheel rake (Page 21).
4. Refer to Buffing Compound Selection and Buffing
Sequence Key on Page 17.
5. Refer to Buffing Wheel Selection and Buffing
Wheel Sequence Key on Pages 18.
2. Incorrect stroke for buffing compound/
wheel/material.
3. Contaminated buffing compounds on wheel.
4. Wrong buffing compound for material.
5. Inappropriate buffing wheel.
-22-
Model W1847 (For Machines Mfd. Since 9/17)
Electrical Safety Instructions
These pages are current at the time of printing. However, in the spirit of improvement, we may make
changes to the electrical systems of future machines. Compare the manufacture date of your machine to
the one stated in this manual, and study this section carefully.
If there are differences between your machine and what is shown in this section, call Technical Support
at (360) 734-3482 for assistance BEFORE making any changes to the wiring on your machine. An updated
wiring diagram may be available. Note: Please gather the serial number and manufacture date of your
machine before calling. This information can be found on the main machine label.
SHOCK.HAZARD. Working on wiring that is
connected to a power source is extremely
dangerous. Touching electrified parts will
result in personal injury including but not
limited to severe burns, electrocution,
or death. Disconnect the power from
the machine before servicing electrical
components!
MODIFICATIONS. Using aftermarket parts or
modifying the wiring beyond what is shown
in the diagram may lead to unpredictable
results, including serious injury or fire.
MOTOR.WIRING. The motor wiring shown
in these diagrams is current at the time
of printing, but it may not match your
machine. Always use the wiring diagram
inside the motor junction box.
QUALIFIED.ELECTRICIAN. Due to the inherent
hazards of electricity, only a qualified
electrician should perform wiring tasks on
this machine. If you are not a qualified
electrician, get help from one before
attempting any kind of wiring job.
CAPACITORS/INVERTERS. Some capacitors
and power inverters store an electrical
charge for up to 10 minutes after being
disconnected from the power source.
To reduce the risk of being shocked,
wait at least this long before working on
capacitors.
WIRE.CONNECTIONS. All connections must
be tight to prevent wires from loosening
during machine operation. Double-check all
wires disconnected or connected during any
wiring task to ensure tight connections.
WIRE/COMPONENT.DAMAGE..Damaged wires
or components increase the risk of serious
personal injury, fire, or machine damage. If
you notice that any wires or components are
damaged while performing a wiring task,
replace those wires or components before
completing the task.
CIRCUIT.REQUIREMENTS. You MUST follow
the requirements at the beginning of this
manual when connecting your machine to a
power source.
EXPERIENCING.DIFFICULTIES. If you are
experiencing difficulties understanding
the information included in this section,
contact our Technical Support at
(360) 734-3482.
The photos and diagrams
included in this section are
best viewed in color. You
can view these pages in
color at www.shopfox.biz.
BLUE
WHITE
BROWN
GREEN
GRAY
YELLOW
YELLOW
GREEN
PURPLE
RED
ORANGE
PINK
-23-
LIGHT
BLUE
BLUE
WHITE
TURQUOISE
SERVICE
WIRING DIAGRAM COLOR KEY
BLACK
Model W1847 (For Machines Mfd. Since 9/17)
Wiring Diagram
This. motor. wiring. diagram. is. current. at. the. time. of.
printing;. however,. always. use. the. diagram. on. the.
inside.of.the.junction.box.cover.when.rewiring.your.
motor!
Read
Page 23
STOP
Before
Wiring
Figure 13. W1847 Wiring.
ON/OFF Button
250V
101
20A
Motor 115V
Start Capacitor
300MFD 125V
Ground
Neutral
Hot
SERVICE
Ground
NEMA 5-15 Plug
ACCIDENTAL INJURY
HAZARD!
Disconnect power
supply before
adjustments, setup
or maintenance!
-24-
Model W1847 (For Machines Mfd. Since 9/17)
PARTS
Main System
30
29
29
35
11
10
9
49
8
49
35 29
29
7
31
5
4
2
13
15
3
1
19
20
33
36
22 28
16
18
34
12
14
15
25
26
27
28
23
21
24
8
9
10
11
REF PART #
DESCRIPTION
REF PART #
DESCRIPTION
1
2
3
4
5
7
8
9
10
11
12
13
14
15
16
18
19
MOTOR BASE
MOTOR CASE
FLAT HD SCR 5/16-18 X 1-1/4
STATOR
ROTOR
MOTOR FAN
BALL BEARING 6206ZZ
MOTOR END COVER
LOCK WASHER 1/4
PHLP HD SCR 1/4-20 X 5/8
CORD CLAMP
POWER CORD 3W 16G 72" 5-15P
STRAIN RELIEF 3/8" TYPE-1
FLANGE SCREW 10-24 X 3/8
SWITCH PANEL
PULL ON/PUSH OFF SWITCH 20A 250V
LOCK WASHER 5/16
20
21
22
23
24
25
26
27
28
29
30
31
33
34
35
36
49
HEX NUT 5/16-18
TAP SCREW #6 X 1/2
CAPACITOR CLAMP
S CAPACITOR 300MFD 125V 1-3/4 X 3-3/8
WIRE NUT
FLOOR PLATE
RUBBER FOOT
FLAT WASHER #10
PHLP HD SCR 10-24 X 1/2
WHEEL FLANGE 5/8 BORE
HEX NUT 5/8-11 LH
HEX NUT 5/8-11
CENTRIFUGAL SWITCH 3450 RPM
CONTACT SWITCH PLATE
T-BUSHING 1 X 3/4 X 3/8
LOCK WASHER #10
T-BUSHING 3/4 X 5/8 X 5/16
X1847001
X1847002
X1847003
X1847004
X1847005
X1847007
X1847008
X1847009
X1847010
X1847011
X1847012
X1847013
X1847014
X1847015
X1847016
X1847018
X1847019
X1847020
X1847021
X1847022
X1847023
X1847024
X1847025
X1847026
X1847027
X1847028
X1847029
X1847030
X1847031
X1847033
X1847034
X1847035
X1847036
X1847049
PARTS
-25-
BUFFING SYSTEM
WARNING!
Specifications
Motor: 1 HP, 115V, 1-Ph, 60 Hz
Full-Load Current Rating: 14A
Motor Speed: 3450 RPM
Max. Wheel Diameter: 12"
Buffing Wheel Arbor: 5/8"
Buffing Wheel Max. Width: 2"
Weight: 53 lbs.
Date
S/N
Mfd. for Woodstock in Taiwan
To reduce risk of serious personal injury when using this machine:
1. Read & understand owner’s manual before operating.
2. Always wear approved eye protection and respirator.
3. Only plug power cord into a grounded outlet.
4. Never place hands on rotating buffing wheel.
5. Do not wear loose clothing, gloves, or jewelry. Secure long hair and
button all long-sleeve shirts.
6. Always disconnect power before changing wheels or adjusting.
7. Do not operate under the influence of drugs or alcohol.
8. Make sure machine is properly adjusted and set up correctly before
starting motor.
9. Make sure machine is secured to a stable surface before starting.
10. Keep a firm grip on the workpiece and ensure it is properly
supported throughout the buffing operation.
11. Do not use workpiece with nails, loose knots, splinters or any
condition that may cause the wheel to grab and project workpiece.
12. Prevent unauthorized use by children or untrained users.
Model W1847 (For Machines Mfd. Since 9/17)
Labels & Cosmetics
102
MODEL W1847
BUFFING SYSTEM
101
WARNING!
Specifications
WARNING!
READ and UNDERSTAND
MANUAL to avoid serious
injury! If a manual is not
available, DO NOT use
machine! Instead, go to
www.woodstockint.com
or call (360) 734-3482.
WARNING!
EYE/LUNG INJURY
HAZARD!
Always wear safety
glasses and a
respirator when
using this machine.
WARNING
ACCIDENTAL INJURY
HAZARD!
Disconnect power
supply before
adjustments, setup
or maintenance!
Motor: 1 HP, 115V, 1-Ph, 60 Hz
Full-Load Current Rating: 14A
Motor Speed: 3450 RPM
Max. Wheel Diameter: 12"
Buffing Wheel Arbor: 5/8"
Buffing Wheel Max. Width: 2"
Weight: 53 lbs.
WARNING
ENTANGLEMENT
HAZARD!
Tie back long hair
and roll up sleeves
before using this
machine.
Date
S/N
Mfd. for Woodstock in Taiwan
105
MODEL W1847
WARNING!
BUFFING SYSTEM
READ and UNDERSTAND
MANUAL to avoid serious
injury! If a manual is not
available, DO NOT use
machine! Instead, go to
www.woodstockint.com
or call
734-3482.
using
this(360)
machine:
WARNING!
Specifications
Motor: 1 HP, 115V, 1-Ph, 60 Hz
Full-Load Current Rating: 14A
Motor Speed: 3450 RPM
Max. Wheel Diameter: 12"
Buffing Wheel Arbor: 5/8"
Buffing Wheel Max. Width: 2"
Weight: 53 lbs.
To reduce risk of serious personal injury when using this machine:
1. Read & understand owner’s manual before operating.
2. Always wear approved eye protection and respirator.
3. Only plug power cord into a grounded outlet.
4. Never place hands on rotating buffing wheel.
5. Do not wear loose clothing, gloves, or jewelry. Secure long hair and
button all long-sleeve shirts.
6. Always disconnect power before changing wheels or adjusting.
7. Do not operate under the influence of drugs or alcohol.
8. Make sure machine is properly adjusted and set up correctly before
starting motor.
9. Make sure machine is secured to a stable surface before starting.
10. Keep a firm grip on the workpiece and ensure it is properly
supported throughout the buffing operation.
11. Do not use workpiece with nails, loose knots, splinters or any
condition that may cause the wheel to grab and project workpiece.
12. Prevent unauthorized use by children or untrained users.
WARNING!
EYE/LUNG INJURY
HAZARD!
Always wear safety
glasses and a
respirator when
using this machine.
To reduce risk of serious personal injury when
1. Read & understand owner’s manual before operating.
2. Always wear approved eye protection and respirator.
3. Only plug power cord into a grounded outlet.
4. Never place hands on rotating buffing wheel.
5. Do not wear loose clothing, gloves, or jewelry. Secure long hair and
button all long-sleeve shirts.
6. Always disconnect power before changing wheels or adjusting.
7. Do not operate under the influence of drugs or alcohol.
8. Make sure machine is properly adjusted and set up correctly before
starting motor.
9. Make sure machine is secured to a stable surface before starting.
10. Keep a firm grip on the workpiece and ensure it is properly
supported throughout the buffing operation.
11. Do not use workpiece with nails, loose knots, splinters or any
condition that may cause the wheel to grab and project workpiece.
12. Prevent unauthorized use by children or untrained users.
WARNING
ACCIDENTAL INJURY
HAZARD!
Disconnect power
supply before
adjustments, setup
or maintenance!
WARNING
ENTANGLEMENT
HAZARD!
Tie back long hair
and roll up sleeves
before using this
machine.
104
Date
S/N
Mfd. for Woodstock in Taiwan
REF PART #
DESCRIPTION
REF PART #
101 X1847101 4-WAY COMBO WARNING LABEL
102 X1847102 MACHINE ID LABEL
103 X1847103 ELECTRICITY LABEL
WARNING!
READ and UNDERSTAND
MANUAL to avoid serious
injury! If a manual is not
available, DO NOT use
machine! Instead, go to
www.woodstockint.com
or call (360) 734-3482.
WARNING!
EYE/LUNG INJURY
HAZARD!
Always wear safety
glasses and a
respirator when
using this machine.
WARNING
ACCIDENTAL INJURY
HAZARD!
Disconnect power
supply before
adjustments, setup
or maintenance!
103
DESCRIPTION
104 X1847104 DIRECTIONAL ARROW LABEL
105 X1847105 TOUCH-UP PAINT, SHOP FOX WHITE
WARNING
ENTANGLEMENT
HAZARD!
Tie back long hair
and roll up sleeves
before using this
machine.
PARTS
Safety.labels.warn.about.machine.hazards.and.how.to.prevent.serious.personal.injury..The.owner.
of.this.machine.MUST.maintain.the.original.location.and.readability.of.all.labels.on.this.machine..
If.any.label.is.removed.or.becomes.unreadable,.REPLACE.that.label.before.allowing.machine.to.
be.operated.again..Contact.us.at.(360).734-3482.or.www.woodstockint.com.to.order.new.labels..
-26-
Model W1847 (For Machines Mfd. Since 9/17)
Fold along dotted lIne
place
stamp
Here
Woodstock international inc.
p.o. box 2309
bellingham, Wa 98227-2309
Fold along dotted lIne
tape along edges--please do not staple
WARRANTY
WARRANTY
Woodstock International, Inc. warrants all Shop Fox machinery to be free of defects from workmanship
and materials for a period of two years from the date of original purchase by the original owner.
This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence or
accidents, lack of maintenance, or reimbursement of third party expenses incurred.
Woodstock International, Inc. will repair, replace, or arrange for a dealer refund, at its expense and
option, the Shop Fox machine or machine part proven to be defective for its designed and intended
use, provided that the original owner returns the product prepaid to an authorized warranty or repair
facility as designated by our Bellingham, Washington office with proof of their purchase of the product
within two years, and provides Woodstock International, Inc. reasonable opportunity to verify the
alleged defect through inspection. If it is determined there is no defect, or that the defect resulted
from causes not within the scope of Woodstock International Inc.'s warranty, then the original owner
must bear the cost of storing and returning the product.
This is Woodstock International, Inc.’s sole written warranty and any and all warranties that may be
implied by law, including any merchantability or fitness, for any particular purpose, are hereby limited
to the duration of this written warranty. We do not warrant that Shop Fox machinery complies with
the provisions of any law, acts or electrical codes. We do not reimburse for third party repairs. In no
event shall Woodstock International, Inc.’s liability under this limited warranty exceed the purchase
price paid for the product, and any legal actions brought against Woodstock International, Inc. shall be
tried in the State of Washington, County of Whatcom. We shall in no event be liable for death, injuries
to persons or property or for incidental, contingent, special or consequential damages arising from the
use of our products.
Every effort has been made to ensure that all Shop Fox machinery meets high quality and durability
standards. We are commited to continuously improving the quality of our products, and reserve the
right to change specifications at any time.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement