Meridian DSP750 Loudspeaker Quick Start Guide

Meridian DSP750 Loudspeaker Quick Start Guide
This guide explains how to install the Meridian DSP750
loudspeaker into an RF600 wall box, available separately.
For further information please visit:
3. Lock the frame into place
https://www.meridian-audio.com/DSP750
If the loudspeaker is not mounted behind a screen or other
fabric covering, the grille can be fitted to the front of the
loudspeaker.
1. Contents
Each DSP750 loudspeaker is supplied with the following
components:
•
•
•
•
•
•
•
•
•
Mounting frame.
Mains cable.
M5 x 25mm clamping screws – 12 pieces.
M5 x 10mm lock screws – 8 pieces.
M5 x 20mm guide-in screws – 12 pieces.
Grille.
Grab handle.
M3 Allen key.
Grille extractor tools – 2 pieces.
2. Fit the mounting frame to the wall
The mounting frame is located within the packaging
underneath the loudspeaker. Remove the loudspeaker from
the box to gain access to the frame.
Clamping
screws
(M5 x 25mm)
Lock
screws
(M5 x 10mm)
Clamp the frame to the wall with the 12 M5 x 25mm buttonhead clamping screws. After tightening these screws for a
few turns you will feel considerable resistance due to the
shakeproof nylon inserts on the receiving nuts. Tighten just
enough to clamp the frame to the wall. Do not overtighten as
this may distort the frame.
Mounting
frame
6. Controlling the loudspeaker
Once the frame is flush against the wall, lock it into place with
the eight M5 x 10mm button-head lock screws, and lock tight.
Right
RS232
On
*To enable
Centre Elevation
see user guide
L+R
Left or Centre*
Off
4. Fit the loudspeaker to the mounting frame
The loudspeaker can be controlled in one of three ways.
Grab handle
Guide-in
screws
(M5 x 20mm)
•
•
•
By another Meridian product within the system.
Via its infra-red receiver, using a Meridian System Remote.
Using RS232 commands.
7. Channel selector switch
To help install the loudspeaker, a grab handle is supplied in
the foam packing piece at the bottom end of the packaging.
Using the grab handle as shown, sit the loudspeaker on the
lower edge of the wall box.
Plug in the RJ45 cable(s), and connect the mains cable
between the loudspeaker and the wall-box.
Slide the mounting frame into the wall box.
5. FIT THE GRILLE TO THE LOUDSPEAKER
With the help of the grab handle, slide the loudspeaker into
position, inserting the top of the loudspeaker into the wall
box first.
Fix with the 12 M5 x 20mm guide-in screws. To fit the last pair
of screws remove the grab handle, which is no longer required.
Set the channel selector switch on each loudspeaker
according to its role in the system:
If a single loudspeaker is used on its own, such as in a
soundbar application, select L+R to play a balanced mix of left
and right audio.
If the loudspeaker is to be used as a centre channel in a
multichannel system select Left or Centre. If Centre Elevation
is required refer to the User Guide.
If the loudspeaker is on the left of the system (two-channel or
multichannel) select Left or Centre.
If the loudspeaker is on the right of the system (two-channel
or multichannel) select Right.
Important safety instructions
•
•
•
•
•
•
•
Read the instructions.
Keep these instructions.
Follow all instructions.
Do not use this apparatus near water.
Clean only with a dry cloth.
Install only in accordance with the manufacturer’s instructions.
Refer all servicing to approved service personnel.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO
NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.
This apparatus has been designed with Class 1 construction and
must be connected to a mains socket outlet with a protective earthing
connection (the third grounding pin).
This apparatus uses a single-pole power switch. As a result it is not
isolated from AC mains power when switched off at the front panel. The
apparatus may be isolated from mains power either by unplugging the
power connector from the rear of the unit, or by unplugging the connector
at the opposing end of the power cord or cable from its supply outlet. As a
result, either or both of these connectors should remain accessible.

WARNING!
RISK OF ELECTRIC SHOCK – DO NOT OPEN
ATTENTION!
NE PAS OUVRIR – RISQUE DE DÉCHARGE ÉLECTRIQUE
Caution: to reduce the risk of electric shock, do not remove cover.
No user serviceable parts inside. Refer servicing to qualified service
personnel.

The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of uninsulated “dangerous voltage” within the
product’s enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the
literature accompanying the appliance.
IP20 Equipment
Climate
The equipment has been designed for use in moderate climates and
in domestic situations.
Only use at an altitude not exceeding 2000m.
To avoid overheating
• Do not position the product in direct sunlight.
• Do not position the product near heat sources, such as a radiator.
• Leave at least 10cm around the product to ensure sufficient ventilation.
Radio interference
FCC Warning: This equipment generates and can radiate radio
frequency energy and if not installed and used correctly in accordance
with our instructions may cause interference to radio communications
or radio and television reception. It has been type-tested and complies
with the limits set out in Subpart J, Part 15 of FCC rules for a Class B
computing device. These limits are intended to provide reasonable
protection against such interference in home installations.
QUICK START
GUIDE
EEC: This product has been designed and type-tested to comply with
the limits set out in EN55032:2015 and EN55024:2010 + A1:2015.
Safety warnings

Safety warnings
• Do not expose the unit to dripping or splashing.
• Do not place any object filled with liquid, such as a vase, on the unit.
• Do not place naked flame sources, such as lighted candles, on the unit.
≤2000m
Specifications
Physical
Dimensions: 1230mm x 203mm x 102mm (H x W x D)
Weight: 16kg
Power
500W max
This product is available factory pre-set in the following voltage options:
• 100V AC 50-60Hz
• 110-120V AC 50-60Hz
• 220-240V AC 50-60Hz
Meridian Audio reserves the right to amend product specifications at
any time.
Copyright © 2019 Meridian Audio Ltd.
Part no: P88471
Designed and manufactured in the UK by Meridian
Audio Ltd. Meridian Audio reserves the right to make
changes and improvements to any of the products
described in this document without prior notice.
Visit us on the Web
www.meridian-audio.com
DSP750 IN-WALL DIGITAL
ACTIVE LOUDSPEAKER
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement