AGA Masterchef Gas Conversion Owner's manual

AGA Masterchef Gas Conversion Owner's manual
GB
FR
GB
NL
FR
DE
NL
SE
DE
NO
SE
IT
NO
IE
IT
DK
IE
PT
DK
PL
PT
RU
PL
GR
RU
FI
GR
ES
FI
ES
GB Conversion to Another Gas
FR
NL
Modification
DE en vue de l’Utilisation d’un Autre Gaz
SE
GB NO
Ombouwen
voor Gebruik met een Andere Gassoort
FR IT
GB
NL IE
FR
DK
DE Umstellung
auf Eine Andere Gasart
NL
SE PT
DE
NO PL
SEIT Konvertering
till en Annan Typ av Gas
RU
NO
IE GR
IT
DK FI
IEPT ES
DK
PL
PT
RU
PL
GR
RU
FI
GR
ES
FI
ES
F200126 - 01
Warning - Servicing to be carried out by an authorised person
Disconnect from electricity and gas before servicing.
Check appliance is safe when you have finished.
GB
FR
Fig.NL
1.1
DE A
SE
C
NO
IT B
D
IE
A - Burner head, B - Base, C - Brass venturi, D - Burner ring
DK
PT
Fig. 1.2
PL
RU
GR
FI
ES
Conversion to Another Gas
Servicing - Warning
This conversion must be performed by a competent person.
After conversion the installation must comply with the
relevant regulations and also the local electricity supply
company requirements. Read the instructions before
converting this appliance.
ArtNo.311-0034 - Burner head off
Failure to convert the appliance correctly could invalidate any
warranty or liability claims and lead to prosecution.
This instruction must be used in conjunction with the rest
of the appliance instruction, in particular for information on
Standards, cooker positioning, connection hose suitability etc.
When servicing or replacing gas-carrying components
disconnect from gas before commencing operation and
check appliance is gas sound after completion.
Do not use re-conditioned or unauthorised gas controls.
Conversion
Disconnect from electricity and gas before servicing. Check
appliance is safe when you have finished.
Fig. 1.3
This appliance is supplied set for G20 natural gas at 20 millibar.
Rubber tubing
A conversion kit for other gases is supplied with the cooker.
Check in the table that the appliance can be converted to
your gas type.
Injectors
Remove pan supports and burner heads.
Remove burner heads. Undo the large brass nuts and remove
the brass venturis and brass rings (Fig. 1.1).
Use a long box spanner to access and remove the old injectors.
Using the rubber tubing, provided in the conversion kit, fit
over the end of the socket wrench (Fig. 1.2).
Fig. 1.4
Carefully push the open end of the tubing onto the orifice
(Fig. 1.3). Unscrew the orifice fully and lift clear of the cooktop.
Save the injectors removed from the appliance for possible
future use. Fit the new injectors, see the table (Table 1.1) for
the correct type.
Insert the new orifice into the open end of the rubber tube
which is attached to the socket wrench. Screw into the orifice
carrier as far as possible and lift the socket wrench away
(Fig. 1.4).
Remove the rubber tubing from the socket wrench and
tighten all of the orifices.
Replace the rings on the burners. Screw in the hexagon
headed venturi to make fitting the burners easier. DO NOT
tighten yet.
When all the burner bases and venturis have been fitted
tighten the venturi nuts.
2
Warning - Servicing to be carried out by an authorised person
Disconnect from electricity and gas before servicing.
Check appliance is safe when you have finished.
GB
FR
NL1.5
Fig.
ArtNo.0102-0011 - Screwing
the control valve bypass screw
DE
SE
NO
IT
IE
DK
PT
PL
RU
Burner venturis
GR
For some gases, the venturi tubes will have to be changed, from the
standard 10.5 mm ones, to the smaller 7mm internal diameter
FIones
found in the conversion kit. Look in the table to see if they need to
be changed for your gas.
ES
Tap adjustment
Pull off all the control knobs and timer buttons.
Open both oven doors and remove the fixing screws
underneath and top rear of the control panel
Pull forward and gently lift the control panel. Rest the control
panel on a cloth to protect the control panel from any
damage
Bypass screw adjustment
Turn the bypass screw on each control clockwise all the way
till it stops (Fig. 1.5).
Fit the control panel, over and push the control panel into
position. Replace the fixing screws you removed.Refit the
knobs.
B
B
C
B
A
10.5mm
Gas Group
Pressure
2H, 2E, 2E+ Natural Gas
2ELL
2L
3+
Natural Gas
Natural Gas
Liquid Petroleum Gas
20 mbar
20/25 mbar
20 mbar
25 mbar
Burner
7mm
Burner venturi
Burner ring
A
95
10,5mm
No
B
120
10,5mm
No
C
165
10,5mm
No
A
102
7mm
No
B
130
7mm
No
C
173
10,5mm
No
A
96
7mm
No
B
123
10,5mm
No
C
163
10,5mm
No
A
64
10,5mm
No
B
82
10,5mm
No
C
107
10,5mm
28-30 & 37 mbar
Large ring in conversion kit
3B/P
Liquid Petroleum Gas
A
64
10,5mm
No
B
82
10,5mm
No
C
107
10,5mm
A
53
7mm
No
B
71
10,5mm
No
C
92
10,5mm
30 mbar
Large ring in conversion kit
3B/P
Liquid Petroleum Gas
50 mbar
Large ring in conversion kit
Table 1.1
3
GB
FR
NL
Fig.
1.6
DE
SE
NO
IT
IE
DK
PT
PL
RU
GR
FI
ES
Warning - Servicing to be carried out by an authorised person
Disconnect from electricity and gas before servicing.
Check appliance is safe when you have finished.
Liquid Petroleum Gas
If you are converting to Liquid Petroleum Gas the burner ring
in the centre burner must be changed for the large ring in the
conversion kit (Fig. 1.6).
4
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement