AJA OG-3G-AMA openGear 3G-SDI Analog Audio Embedder/Disembedder Manual

AJA OG-3G-AMA  openGear 3G-SDI Analog Audio Embedder/Disembedder Manual

OG-3G-AMA
openGear Card
Installation and Operation Guide
Version 1.0
Published May 14, 2018

Notices
Trademarks
AJA® and Because it matters.® are registered trademarks of AJA Video Systems, Inc.
for use with most AJA products. AJA™ is a trademark of AJA Video Systems, Inc. for
use with recorder, router, software and camera products. Because it matters.™ is a
trademark of AJA Video Systems, Inc. for use with camera products.
CION®, Corvid Ultra®, lo®, Ki Pro®, KONA®, KUMO®, ROI® and T-Tap® are registered
trademarks of AJA Video Systems, Inc.
AJA Control Room™, KiStor™, Science of the Beautiful™, TruScale™, TruZoom™,
V2Analog™ and V2Digital™ are trademarks of AJA Video Systems, Inc.
All other trademarks are the property of their respective owners.
Copyright
Copyright © 2018 AJA Video Systems, Inc. All rights reserved. All information in
this manual is subject to change without notice. No part of the document may be
reproduced or transmitted in any form, or by any means, electronic or mechanical,
including photocopying or recording, without the express written permission of AJA
Video Systems, Inc.
Contacting AJA Support
When calling for support, have all information at hand prior to calling. To contact AJA
for sales or support, use any of the following methods:
Telephone
+1.530.271.3190
FAX
+1.530.271.3140
Web
https://www.aja.com
Support Email
support@aja.com
Sales Email
sales@aja.com
OG-3G-AMA openGear Card v1.0
2
www.aja.com

Contents
Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Copyright . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Contacting AJA Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Chapter 1 – Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . openGear and AJA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
OG-3G-AMA I/O Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
User Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DIP Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DashBoard Control System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Rear OG-3G-AMA Card Installation . . . . . . . . . . . . . . . . . . . . . . . . . . .
Front OG-3G-AMA Card Installation . . . . . . . . . . . . . . . . . . . . . . . . . . Cabling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
4
5
5
5
6
6
6
6
7
7
8
9
Chapter 2 – Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Default Operational Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
DIP Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
DIP Switch Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Using the DashBoard Control System . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Control Interface Basic Components . . . . . . . . . . . . . . . . . . . . . . . . .13
Three OG-3G-AMA Use Cases . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Audio 1 Tab Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Audio 2 Tab Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Setup Tab Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Upload Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Rebooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
Appendix A – Specifications . . . . . . . . . . . . . . . . . . . . . . . . 27
OG-3G-AMA Tech Specs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
Appendix B – Safety and Compliance . . . . . . . . . . . . . . . . . . 29
Warranty and Liability Information . . . . . . . . . . . . . . . . . . . . 38
Limited Warranty on Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Limitation of Liability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
Governing Law and Language; Your Rights. . . . . . . . . . . . . . . . . . . . . . .39
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
OG-3G-AMA openGear Card v1.0
3
www.aja.com

Chapter 1 – Introduction
Overview
The OG-3G-AMA is an 8-channel openGear analog audio embedder/
disembedder, supporting 3G/HD/SD-SDI video input and output up to 1080p 60.
The unit can be configured to pass, embed or disembed input audio on a channel
pair basis. The three-pin terminal block audio connectors can be configured as
inputs or outputs.
The OG-3G-AMA automatically detects and configures to the input video
standard. Horizontal ancillary data (HANC) packets in compliance with SMPTE
291M can also be dropped at the input.
NOTE: 2048 x 1080p/PsF 29.97 and 30 formats support a maximum of 8 channels
embedded audio.
The OG-3G-AMA can be configured to function in the following ways:
• 8-channel embedder
• 8-channel disembedder
• 4-channel embedder and 4-channel disembedder
• 6-channel embedder and 2-channel disembedder
• 2-channel embedder and 6-channel disembedder
Designed for use in high-density openGear’s 2RU frames including AJA’s OG-3-FR
2RU frame, new DashBoard Software support on Windows®, macOS® and Linux®
offers remote control and monitoring of the openGear architecture and provides
convenient and industry-standard configuration, monitoring and control options
over a PC or local network.
Features
• 3G/HD/SD-SDI Embedder/Disembedder
• 1x BNC 3G-SDI Input
• 1x BNC 3G-SDI Output
OG-3G-AMA openGear Card v1.0
4
www.aja.com

• 8 Channel Balanced Analog Audio I/O
• 8x 3-Pin Terminal Block Audio Connectors
• 8x Audio Mating Connectors
• Remote Configuration through DashBoard Control System for an openGear
Frame
• Local Configuration through DIP Switches
• Embed To Selection (Ch 1-8 or Ch 9-16) on a Channel Pair Basis
• Disembed From Selection (Ch 1-8 or Ch 9-16) on a Channel Pair Basis
• Strip or Pass Incoming HANC Data
• Set Analog Audio Operating Level
• Requires Two Slots in openGear Frame
• Rear I/O Card Included
openGear and AJA
openGear is an open-architecture, modular frame system designed by Ross
Video and supported by a diverse range of terminal equipment manufacturers,
including AJA. Ross Video manufactures the frames, power supplies and network
cards for openGear. AJA is a reseller of the openGear frames.
AJA Video is a leading manufacturer of video interface technologies, converters,
digital video recording solutions and professional cameras, bringing highquality, cost-effective products to the professional, broadcast and postproduction markets. AJA products, including openGear cards, are designed and
manufactured at our facilities in Grass Valley, California.
OG-3G-AMA I/O Connections
Figure 1. I/O Connections for the OG-3G-AMA
SDI Input
BNC (J1)
SDI Output
BNC (J2)
AUD1
AUD 5
AUD 2
AUD 6
AUD 3
AUD 7
AUD 4
AUD 8
Each 3-pin analog audio connector carries one channel of analog audio that can
be configured to be an input or an output.
User Controls
User Control options for the OG-3G-AMA consist of DIP switches on the card
and the DashBoard Control System from Ross Video. Both options are described
below.
OG-3G-AMA openGear Card v1.0
5
www.aja.com

DIP Switches
The OG-3G-AMA has an 8 position DIP switch accessible on the card. The
DIP switches can be used to configure the unit’s audio embedding and
disembedding, and to control ancillary data. When using DIP switches for
control, DashBoard displays only the Card and Status tabs and cannot be used for
configuration.
Figure 2. OG-3G-AMA DIP Switches
CONTROL
LOCAL
REMOTE
EMBED 1/2
ON
OFF
EMBED 3/4
ON
OFF
EMBED 5/6
ON
OFF
EMBED 7/8
ON
OFF
EMBED GROUP
1/2
3/4
DISEMBED GROUP 1/2
3/4
PASS HANC
OFF
ON
The exact functions of the DIP switch are described in "DIP Switch Settings" on
page 11.
DashBoard Control System
The DashBoard Control System, created by Ross Video, provides a control
interface between Windows, macOS and Linux computers and the cards installed
in an openGear frame. DashBoard operates through TCP/IP communication
and requires an Ethernet connection between the controlling computer and an
openGear frame.
Details for acquiring and using the DashBoard Control System are provided in
"Using the DashBoard Control System" on page 13.
Parts List
Quantity
Description
1
OG-3G-AMA Front Card in ESD bag
1
BNC Rear Card
8
WECO mating connectors, part number
107654-00
Installation
Summary
Installing an OG-3G-AMA card into a OG3 openGear frame consists of the
following steps:
• Install the Rear Panel onto the back of the frame corresponding to the slot pair
you will be using for the OG-3G-AMA card.
• Insert the OG-3G-AMA card into the frame in the right (even numbered) slot of
the pair.
• Connect the BNC and audio cabling to the Rear Panel.
OG-3G-AMA openGear Card v1.0
6
www.aja.com

ESD Susceptibility - Static discharge can cause serious damage to sensitive
semiconductor devices. Avoid handling circuit boards in high static
environments such as carpeted areas, and when wearing synthetic fiber clothing.
Always exercise proper grounding precautions when working on circuit boards
and related equipment.
Unpacking
Unpack each openGear product you received from the shipping container and
ensure that all items are included. If any items are missing or damaged, contact
your sales representative or AJA directly.
Rear OG-3G-AMA Card Installation
1. Ensure that the frame is properly installed.
2. Locate the card frame slot on the rear of the openGear frame into which you
wish to install the openGear card.
NOTE: An OG-3G-AMA card occupies two slots in the frame.
3. Using a Phillips screwdriver, unscrew the top screw from the desired blank
rear plate and remove the rear plate.
4. Seat the bottom of the Rear Card in the seating slot at the base of the frame
back plane.
Figure 3. Rear Card Inserting Into Frame Seating Slot
5. Align the top screw of the Rear Card with the screw hole on the top edge of
the frame back plane.
6. Ensure the Rear Card aligns with the desired card slot before tightening the
screw.
7. Using a Phillips screwdriver, fasten the Rear Card to the frame back plane.
Do not over tighten.
OG-3G-AMA openGear Card v1.0
7
www.aja.com

Figure 4. Rear Card Inserted Into Frame Seating Slot
8. Ensure proper frame cooling and ventilation by having all rear frame slots
covered with rear modules or blank metal plates if plates are not preinstalled.
Front OG-3G-AMA Card Installation
1. Open the openGear frame door as follows:
A. Gently pull the side door tabs towards the center of the door, releasing the
door from the frame.
B. Using both hands, pull the door towards you. The door extender arms
prevent the door from falling.
2. Locate the Rear Card you installed as described above. The interior slot
number is dependent on the slot combinations into which you installed the
Rear Card. This allows adequate spacing to avoid damaging the card, the
cards installed in the neighboring slots, or both.
3. Hold the card by the edges and carefully align the card edges with the rails
inside the frame. The slots are numbered starting from the left-most slot
when facing the fame front.
IMPORTANT: OG-3G-AMA cards are installed into the right (even numbered) slot of the
pair in order to connect with the rear panel.
4. Fully insert the card into the frame until the card is properly seated in the
Rear Card.
OG-3G-AMA openGear Card v1.0
8
www.aja.com

Figure 5. OG-3G-AMA card inserted Into Right Slot
5. Close the frame door as follows:
A. Slide the door into the frame.
B. Pull and release the door tabs to ensure the frame door is securely locked
to the frame.
Cabling
Refer to Figure 1. "I/O Connections for the OG-3G-AMA" on page 5 to identify the
input and output signal connectors.
Eight WECO audio mating connectors are included with each OG-3G-AMA.
1. Insert connecting audio wires into their corresponding holes from the rear
(Figure 6).
Figure 6. Rear view of the WECO mating audio connector
2. Tighten the screws on the other side of the audio mating connector (Figure
7).
Figure 7. Front view of the WECO mating audio connector showing the
tightening screws
OG-3G-AMA openGear Card v1.0
9
www.aja.com

3. After you have secured the wiring for each WECO mating audio connector,
connect them to the audio output connectors on the rear panel of the
OG-3G-AMA.
4. Add tie wraps around the audio connectors for strain relief.
OG-3G-AMA openGear Card v1.0
10
www.aja.com

Chapter 2 – Operation
Default Operational Settings
The OG-3G-AMA converter ships from the factory with the following
configuration:
• Local (DIP switch) control (DashBoard shows status only).
• Input analog audio channels 1-8 are embedded to SDI output channels 1-8,
overwriting any existing embedded audio.
• HANC packets for embedded audio channels 1-8 will be overwritten, and all
other HANC packets will be passed through.
• The analog audio operating level is set to 0 dBfs = +24 dBu.
If these settings apply to your requirements, you can simply connect the video
and audio input and output signal cables.
For other applications, you can configure the card using its DIP switch settings, or
by setting Remote (DIP switch) control and using the DashBoard Control System
and a PC or Mac networked to an openGear frame. Analog audio levels can only
be set using the DashBoard Control System.
DIP Switches
The OG-3G-AMA DIP switches configure the audio embedding and
disembedding functions.
CONTROL
LOCAL
REMOTE
EMBED 1/2
ON
OFF
EMBED 3/4
ON
OFF
EMBED 5/6
ON
OFF
EMBED 7/8
ON
OFF
EMBED GROUP
1/2
3/4
DISEMBED GROUP 1/2
3/4
PASS HANC
OFF
ON
DIP Switch Settings
DIP switch settings can be used to configure the functions of the OG-3G-AMA
card. Please see the following Table 1. "Description of the DIP Switch Settings" on
page 12 for detailed descriptions of the DIP switch settings.
OG-3G-AMA openGear Card v1.0
11
www.aja.com

Table 1. Description of the DIP Switch Settings
SWITCH FUNCTION LABEL
LABEL
BEHAVIOR
1
Control
Local
Remote When set to Local, the card can be controlled only through the
DIP switches, although DashBoard will display status. When
set to Remote, the card can be controlled only through the
DashBoard Control System.
2
Embed 1/2
On
Off
When set to On, the audio channels from Analog Audio I/O
connectors 1 and 2 are embedded into the first pair of channels
of the SDI Group selected by switch 6 (Embed Group).
When set to Off, the audio channels from the first two channels
of the SDI Group selected by switch 7 (Disembed Group) are
disembedded and output as analog audio through Analog
Audio I/O connectors 1 and 2.
3
Embed 3/4
On
Off
When set to On, the audio channels from Analog Audio I/O
connectors 3 and 4 are embedded into the second pair of
channels of the SDI Group selected by switch 6 (Embed Group).
When set to Off, the audio channels from the second pair of
channels of the SDI Group selected by switch 7 (Disembed
Group) are disembedded and output as analog audio through
Analog Audio I/O connectors 3 and 4.
4
Embed 5/6
On
Off
When set to On, the audio channels from Analog Audio
I/O connectors 5 and 6 are embedded into the third pair of
channels of the SDI Group selected by switch 6 (Embed Group).
When set to Off, the audio channels from the third pair of
channels of the SDI Group selected by switch 7 (Disembed
Group) are disembedded and output as analog audio through
Analog Audio I/O connectors 5 and 6.
5
Embed 7/8
On
Off
When set to On, the audio channels from Analog Audio I/O
connectors 7 and 8 are embedded into the fourth pair of
channels of the SDI Group selected by switch 6 (Embed Group).
When set to Off, the audio channels from the fourth pair of
channels of the SDI Group selected by switch 7 (Disembed
Group) are disembedded and output as analog audio through
Analog Audio I/O connectors 7 and 8.
6
Embed
Group
1/2
3/4
When set to 1/2, analog audio will be embedded into SDI audio
groups 1/2 (channels 1-8).
When set to 3/4, analog audio will be embedded into SDI audio
groups 3/4 (channels 9-16).
Embedding by channel pair is controlled by switches 2-5.
7
Disembed
Group
1/2
3/4
When set to 1/2, SDI audio group 1/2 (channels 1-8) will be
disembedded to analog audio.
When set to 3/4, SDI audio group 3/4 (channels 9-16) will be
disembedded to analog audio.
Disembedding by channel pair is controlled by switches 2-5.
8
Pass HANC
On
Off
Determine whether or not to pass the incoming embedded
horizontal ancillary data (HANC) packets.
When set to On, all incoming HANC packets are passed unless
the embedder settings require all or part of them to be overwritten.
When set to Off, all incoming HANC packets are dropped before
embedding any new audio packets.
NOTE: 2048x1080p/psf 29.97 and 30 formats support a maximum of 8 channels of
embedded audio. When one of these formats is present and embedding is turned
on, the PASS HANC DIP switch will be ignored and all incoming packets will be
dropped before embedding any new audio packets.
OG-3G-AMA openGear Card v1.0
12
www.aja.com

Using the DashBoard Control System
The DashBoard Control System, created by Ross Video, is available as a free
download from the Ross Video website:
https://www.rossvideo.com/control-systems/dashboard/products/dashboard/
Ross Video offers comprehensive documentation that covers the extensive
capabilities of the DashBoard Control System:
https://www.rossvideo.com/support/documentation/dashboard/
This manual addresses only those essential aspects of the DashBoard Control
System needed to control the OG-3G-AMA card.
Requirements
The DashBoard Control System requires the following components:
• openGear frame with a Frame Controller card
• Ethernet connection betweeen the controlling computer and the openGear
frame
NOTE: The openGear frame ships from AJA with the MFC-8322-S Frame Controller card
for controlling the new AJA DashBoard cards. The openGear frame also supports
the MFC-0G3-N Advanced Networking Frame Controller card, which can be used
to control compatible OG cards.
DashBoard automatically discovers openGear and DashBoard Connect devices,
such as openGear frames and cards that are present and accessible on your
network.
Control Interface Basic Components
The basic components of the DashBoard Control System user interface consist of
the basic tree view of frames and cards, the card information and status panel,
and the parameter controls panel. These elements are shown below in Figure 6.
The basic tree view of frames and cards shows the frames and cards that are
discoverable by DashBoard on your network.
The card information and status panel, shown in the middle panel, display the
basic status of the card currently selected in DashBoard.
The parameter controls panel shows the tabs and parameters that the selected
card has available for configuration and control.
OG-3G-AMA openGear Card v1.0
13
www.aja.com

Figure 8. Main Sections of the DashBoard User Interface
Basic Tree View of
Frames and Cards
Card Information
and Status
Parameter
Controls
Three OG-3G-AMA Use Cases
To provide detailed explanations of how to use the OG-3G-AMA DashBoard
Control System, this section illustrates the following three basic use cases:
1. 8-Channel Embedder
2. 8-Channel Disembedder
3. 4-Channel Embedder and 4-Channel Disembedder
Each use case includes a simplified block diagram and a corresponding screen
capture of the DashBoard Control System configured to match each example.
OG-3G-AMA openGear Card v1.0
14
www.aja.com

Use Case 1: 8-Channel Embedder
Figure 9. 8-Channel Embedder Use Case Simplified Block Diagram
EQ
Cable Driver
Embed and Pass-through
Packet Processor
3G-SDI In
Ch 1 - 8
3G-SDI Out
Ch 9 - 16
Embed To
Control
Analog 1
(Input)
Analog Audio
Embedded on
SDI Output
Ch 1 - 8 or
Ch 9 - 16
Analog 2
(Input)
Analog 3
(Input)
Analog 4
(Input)
8 Channel
ADC
Analog 5
(Input)
Analog 6
(Input)
Analog 7
(Input)
Analog 8
(Input)
DashBoard
Control
DIP Switch
User Interface
DashBoard Embed/Disembed Settings
OG-3G-AMA openGear Card v1.0
Ch 1/2 (9/10) Embed
On
Ch 3/4 (11/12) Embed
On
Ch 5/6 (13/14) Embed
On
Ch 7/8 (15/16) Embed
On
15
www.aja.com

Figure 10. The DashBoard Control System showing the OG-3G-AMA card being
used as an 8-Channel Embedder
In this first example, the OG-3G-AMA is being used as an 8-channel embedder.
Four pairs (eight channels) of analog audio input are being embedded into SDI
channels 1 through 8.
The controls under the Audio 1 tab, under Analog Audio Inputs, show in the
Embed to control that Channels 1-8 have been selected for embedding the
analog audio inputs. Below that, each channel pair Embed control is turned on
which enables embedding.
The reporting panel on the left, under the Status tab, reports under the Analog
Audio I/O section that each pair of audio channels is configured as inputs and is
being embedded into the SDI audio channel pairs for channels 1 through 8.
OG-3G-AMA openGear Card v1.0
16
www.aja.com

Use Case 2: 8-Channel Disembedder
Figure 11. 8-Channel Disembedder Use Case Simplified Block Diagram
Analog 1
(Output)
Analog 2
(Output)
Analog 1 - 8
will output
Ch 1 - 8 or
Ch 9 - 16
Analog 3
(Output)
Ch 1 - 8
DisEmbedder
Analog 4
(Output)
8 Channel
DAC
Analog 5
(Output)
Ch 9 - 16
Analog 6
(Output)
Disembed From
Control
Analog 7
(Output)
Analog 8
(Output)
EQ
Cable Driver
Embed and Pass-through
Packet Processor
3G-SDI In
3G-SDI Out 1
DashBoard
Control
DIP Switch
User Interface
DashBoard Embed/Disembed Settings
OG-3G-AMA openGear Card v1.0
Ch 1/2 (9/10) Embed
Off
Ch 3/4 (11/12) Embed
Off
Ch 5/6 (13/14) Embed
Off
Ch 7/8 (15/16) Embed
Off
17
www.aja.com

Figure 12. The DashBoard Control System showing the OG-3G-AMA card being
used as an 8-Channel Disembedder
In this example, the OG-3G-AMA is being used as an 8-channel disembedder.
Under the Audio 1 tab, under Analog Audio Outputs, the Disembed from control
shows that Channels 1-8 have been selected for disembedding from the SDI
signal. Above that, each channel pair Embed control is turned off.
NOTE: When an Embed control is turned off, it changes the function from embed to
disembed.
This configuration is reflected in the reporting panel on the left, under the
Status tab. Under the Analog Audio I/O section, each pair of audio channels is
configured as outputs and is being used to output disembedded audio from the
SDI signal.
OG-3G-AMA openGear Card v1.0
18
www.aja.com

Use Case 3: 4-Channel Embedder and 4-Channel Disembedder
Figure 13. 4-Channel Embedder and 4-Channel Disembedder Use Case
Simplified Block Diagram
Analog 1
(Output)
Ch 1 - 8
Analog 2
(Output)
8 Channel
DAC
(4 Ch Used)
DisEmbedder
Ch 9 - 16
Analog 3
(Output)
Analog 4
(Output)
Disembed From
Control
EQ
Cable Driver
Embed and Pass-through
Packet Processor
3G-SDI In
Ch 1 - 8
Analog 7
(Input)
3G-SDI Out
Analog Audio
Embedded on
SDI Output
Ch 5 - 8 or
Ch 13 - 16
Ch 9 - 16
Embed To
Control
Analog 5
(Input)
Analog 6
(Input)
Analog 1 - 4
will output
Ch 1 - 4 or
Ch 9 - 12
8 Channel
ADC
(4 Ch Used)
Analog 8
(Input)
DashBoard
Control
DIP Switch
User Interface
DashBoard Embed/Disembed Settings
OG-3G-AMA openGear Card v1.0
Ch 1/2 (9/10) Embed
Off
Ch 3/4 (11/12) Embed
Off
Ch 5/6 (13/14) Embed
On
Ch 7/8 (15/16) Embed
On
19
www.aja.com

Figure 14. The DashBoard Control System showing the OG-3G-AMA card being
used as a 4-Channel Embedder and 4-Channel Disembedder
In this example, the OG-3G-AMA is being used as a 4-channel embedder and
4-channel disembedder. Analog audio from audio inputs 1/2 and 3/4 are being
embedded into SDI channels 1/2 and 3/4, and embedded SDI audio channels 5/6
and 7/8 are being disembedded and output through analog audio outputs 5/6
and 7/8.
Under the Audio 1 tab, the Embed to control under Analog Audio Inputs shows
that Channels 1-8 have been selected for embedding the selected analog audio
inputs.
The Disembed from control Under Analog Audio Outputs shows that Channels
1-8 are selected for disembedding.
The Embed controls are turned on for channel pairs 1/2 and 3/4, and turned off
for channel pairs 5/6 and 7/8. When an Embed control is turned off, it changes the
function from embed to disembed.
The reporting panel on the left, under the Status tab, shows that analog
audio connectors 1/2 and 3/4 are configured as inputs and are being used for
embedding to SDI channels 1/2 and 3/4. Analog audio connectors 5/6 and 7/8 are
configured as outputs and are being used for carrying the disembedded audio
from channels 5/6 and 7/8 from the SDI signal.
OG-3G-AMA openGear Card v1.0
20
www.aja.com

Audio 1 Tab Screen
Click on the Audio 1 tab to view and make changes to the audio embedding and
disembedding settings.
Figure 15. OG-3G-AMA Audio 1 Tab Screen in DashBoard
Analog Audio Inputs
Embed to - Select where you want to embed the analog audio. You can embed
analog audio into one of the following pairs of SDI embedded audio groups:
• Ch 1-8 (Group 1/2) or
• Ch 9-16 (Group 3/4).
Ch 1/2 (9/10) Embed - Selecting On embeds the audio channels from Analog
Audio I/O connectors 1 and 2 into the first pair of channels of the SDI Group
selected with the Embed to control. Selecting Off disembeds the audio
channels from the first two channels of the SDI Group selected with the
Disembed from control and outputs them as analog audio through Analog
Audio I/O connectors 1 and 2.
Ch 3/4 (11/12) Embed - Selecting On embeds the audio channels from Analog
Audio I/O connectors 3 and 4 into the second pair of channels of the SDI
Group selected with the Embed to control. Selecting Off disembeds the audio
channels from the second pair of channels of the SDI Group selected with the
Disembed from control and outputs them as analog audio through Analog
Audio I/O connectors 3 and 4.
OG-3G-AMA openGear Card v1.0
21
www.aja.com

Ch 5/6 (13/14) Embed - Selecting On embeds the audio channels from Analog
Audio I/O connectors 5 and 6 into the third pair of channels of the SDI Group
selected with the Embed to control. Selecting Off disembeds the audio
channels from the third pair of channels of the SDI Group selected with the
Disembed from control and outputs them as analog audio through Analog
Audio I/O connectors 5 and 6.
Ch 7/8 (15/16) Embed - Selecting On embeds the audio channels from Analog
Audio I/O connectors 7 and 8 into the fourth pair of channels of the SDI Group
selected with the Embed to control. Selecting Off disembeds the audio
channels from the fourth pair of channels of the SDI Group selected with the
Disembed from control and outputs them as analog audio through Analog
Audio I/O connectors 7 and 8.
Analog Audio Outputs
Disembed from - Select one of the following pairs of SDI embedded audio
groups that you want to disembed from:
• Ch 1-8 (Group 1/2) or
• Ch 9-16 (Group 3/4).
Audio 2 Tab Screen
Click on the Audio-2 tab to view and make changes to the packet processing and
audio level settings.
Figure 16. OG-3G-AMA Audio 2 Tab Screen in DashBoard
Packet Processing Control
HANC Data - Determine whether or not to include the horizontal ancillary data
(HANC) packets in the embedded audio. The embedder settings from the
Audio 1 tab determine all embedded audio output. Disembedding is not
affected. Select one of the following settings:
• Pass: All incoming HANC packets are passed unless the embedder settings
require all or part of them to be over-written.
OG-3G-AMA openGear Card v1.0
22
www.aja.com

• Remove: All incoming HANC packets are dropped before embedding any
new audio packets.
NOTE: 2048 x 1080p/PsF 29.97 and 30 formats support a maximum of 8 channels of
embedded audio. When one of these formats is present and embedding is turned
on, the PASS HANC setting will be ignored and all incoming packets will be
dropped before embedding any new audio packets.
3G–SDI Level B - For 3G Level B signals, selects either the audio channels of
input Stream A or the audio channels of input Stream B for disembedding.
This setting also controls whether output Stream A or output Stream B will
receive embedded audio. This control has no effect if a 3G Level B signal is not
detected. Select one of the following settings:
• Stream A
• Stream B
Analog Audio Level
Full Scale Digital (dBu) - Select from the following:
• +24 dBu
• +18 dBu
• +15 dBu (professional)
• +12 dBu (consumer)
About Audio Levels
Professional audio equipment has much higher levels than consumer equipment.
A 0 VU reading corresponds to +4 dBu. Connecting a professional +4 dBu device
to a consumer audio input (-7 to -8 dBu) may produce overloading, whereas the
output of a consumer device probably does not have sufficient power to drive a
professional audio input. With consumer and semi-professional audio equipment,
a VU reading of 0 dB is typically referenced to -10 dBV, which is equivalent to -7.78
dBu.
Setup Tab Screen
Click on the Setup tab to view and make changes to the card name or to restore
card settings to factory default values.
Figure 17. OG-3G-AMA Setup Tab Screen in DashBoard
OG-3G-AMA openGear Card v1.0
23
www.aja.com

Card Name - By default, this field is pre-populated with the card name
OG-3G-AMA. You can change the card name by editing the text in the Card
Name field.
Factory Settings - If you would like to revert the card settings to factory default
values, click Restore.
Upload Screen
To Upload New Software
1. Check the AJA website for new software for your OG-3G-AMA. If new
software is found, download it and uncompress the file archive (zip).
2. Click the Upload button in the lower panel of the DashBoard Control System
to open the Upload Software Wizard.
Figure 18. OG-3G-AMA Upload Software Wizard window in DashBoard
3. From the Upload Software Wizard window, select Browse.
4. Navigate to the location of the downloaded .bin file containing the software
update. Select the .bin file, then select Open. The Upload Software Wizard
window displays characteristics of the selected file for uploading.
5. Click Finish. The Uploading to Selected Devices window displays with a
progress bar.
OG-3G-AMA openGear Card v1.0
24
www.aja.com

Figure 19. OG-3G-AMA Uploading to Selected Devices window in DashBoard
6. When the progress bar indicates that the uploading is finished and status
indicates "Complete," click OK.
7. To verify the version of software or firmware currently installed on your
card, select the Card tab from the center panel of DashBoard.
Figure 20. OG-3G-AMA Card Tab Screen in DashBoard indicating the currently
installed software version.
Rebooting
Rebooting is a standard function built in to the DashBoard Control System, and
should only be performed if the board has become unresponsive.
WARNING: During a reboot, any embedding or disembedding operations will be
briefly interrupted, but will be restored once the reboot has completed.
OG-3G-AMA openGear Card v1.0
25
www.aja.com

To Reboot the OG-3G-AMA
1. Click the Reboot button in the lower panel of DashBoard. The reboot
confirmation message displays.
Figure 21. Reboot confirmation window
2. Click Yes. The message "Loading data, please wait. Refreshing device data"
displays for a moment. The card will be offline for a few seconds, and any
current embedding or disembedding operations will be interrupted.
Figure 22. The OG-3G-AMA is briefly offline while rebooting
3. Following a Reboot operation, the board configuration will return to the
settings that were in place at the time of rebooting.
OG-3G-AMA openGear Card v1.0
26
www.aja.com

Appendix A – Specifications
OG-3G-AMA Tech Specs
Video Formats
•
•
•
•
•
•
•
•
(2K) 2048 x 1080p
(2K) 2048 x 1080PsF
(HD) 1920 x 1080p
(HD) 1920 x 1080PsF
(HD) 1920 x 1080i
(HD) 1280 x 720p
(SD) 720 x 576i
(SD) 720 x 480i
Video Input Digital
• 1x 3G-SDI BNC, SMPTE-259/292/424
Video Input Formats
• 1x 3 Gb SDI (level A or B)
• (2K) 2048 x 1080p 23.98, 24, 25, 29.97, 30, 50, 59.94, 60
• (2K) 2048 x 1080PsF 23.98, 24, 25, 29.97, 30
• (HD) 1920 x 1080p 23.98, 24, 25, 29.97, 30, 50, 59.94, 60
• (HD) 1920 x 1080PsF 23.98, 24, 25, 29.97, 30
• (HD) 1920 x 1080i 50, 59.94, 60
• (HD) 1280 x 720p 50, 59.94, 60
• 1x 1.5 Gb SDI
• (2K) 2048 x 1080p 23.98, 24, 25, 29.97, 30
• (2K) 2048 x 1080PsF 23.98, 24, 25, 29.97, 30
• (HD) 1920 x 1080p 23.98, 24, 25, 29.97, 30
• (HD) 1920 x 1080PsF 23.98, 24, 25, 29.97, 30
• (HD) 1920 x 1080i 50, 59.94, 60
• (HD) 1280 x 720p 23.98, 24, 25, 29.97, 30, 50, 59.94, 60
• 1x 270 Mb SDI
• (SD) 625i 50
• (SD) 525i 59.94
Video Output Digital
• 1x 3G-SDI BNC, SMPTE-259/292/424
Video Output Formats
Video Out is a delayed, reclocked version of Video In, at same frame rate, etc.
Video Out is undefined when no input.
• Video Latency, time measured between video input and video output
connector:
• 3G level A = 3.2 usec
• 3G level B = 6.1 usec
• HD (1.5 Gb) = 6.3 usec
• SD (270 Mb) = 17.2 usec
OG-3G-AMA openGear Card v1.0
27
www.aja.com

Audio Inputs and Outputs
• Audio Connectors
• 8 Analog Audio Connections (4 pairs total)
• Each pair configurable to Inputs or Outputs
• Digital Audio Converters
• 24-bit
• Embedded Audio
• SMPTE 272M (SD): 20-bit, 48 kHz synchronous
• SMPTE 299M (3G/HD): 24-bit, 48 kHz synchronous
• Incoming embedded audio can be passed, removed, or overridden.
• 16 Channels supported on the SDI at any given time (8 of which can be from
the analog inputs).
• Embed Path Audio Latency, time measured between audio input and video
output connector:
• 1100 usec
• Disembed Path Audio Latency, time measured between video input and audio
output connector:
• 1200 usec
• Analog Audio Levels
• Configured via Dashboard software:
• Pro 1: 0 dBfs = +24 dBu
• Pro 2: 0 dBfs = +18 dBu
• Pro 3: 0 dBfs = +15 dBu
• Consumer 1: 0 dBfs = +12 dBu
User Controls
• External DIP switch
• openGear DashBoard network control software via Windows, macOS or Linux
Size
• openGear standard form factor, front slot and rear card. Two slots required for
each card
Weight
• 0.5 lb (0.3 kg)
Power
• openGear frame compatible, 5.0 watts max per card
Environment
•
•
•
•
Safe Operating Temperature: 0 to 40 C (32 to 104 F)
Safe Storage Temperature (Power OFF): -40 to 60 C (-40 to 140 F)
Operating Relative Humidity: 10-90% noncondensing
Operating Altitude: <3,000 meters (<10,000 feet)
OG-3G-AMA openGear Card v1.0
28
www.aja.com

Appendix B – Safety and Compliance
Federal Communications Commission (FCC) Compliance Notices
Class A Interference Statement
This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to Part 15, Subpart B of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC Caution
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
Canadian ICES Statement
Canadian Department of Communications Radio Interference Regulations
This digital apparatus does not exceed the Class A limits for radio-noise emissions
from a digital apparatus as set out in the Radio Interference Regulations of
the Canadian Department of Communications. This Class A digital apparatus
complies with Canadian ICES-003.
Règlement sur le brouillage radioélectrique du ministère des Communications
Cet appareil numérique respecte les limites de bruits radioélectriques visant les
appareils numériques de classe A prescrites dans le Règlement sur le brouillage
radioélectrique du ministère des Communications du Canada. Cet appareil
numérique de la Classe A est conforme à la norme NMB-003 du Canada.
European Union and European Free Trade Association (EFTA)
Regulatory Compliance
This equipment may be operated in the countries that comprise the member
countries of the European Union and the European Free Trade Association. These
countries, listed in the following paragraph, are referred to as The European
Community throughout this document:
AUSTRIA, BELGIUM, BULGARIA, CYPRUS, CZECH REPUBLIC, DENMARK, ESTONIA,
FINLAND, FRANCE, GERMANY, GREECE, HUNGARY, IRELAND, ITALY, LATVIA,
LITHUANIA, LUXEMBOURG, MALTA, NETHERLANDS, POLAND, PORTUGAL,
ROMANIA, SLOVAKIA, SLOVENIA, SPAIN, SWEDEN, UNITED KINGDOM, ICELAND,
LICHTENSTEIN, NORWAY, SWITZERLAND
OG-3G-AMA openGear Card v1.0
29
www.aja.com

Declaration of Conformity
Marking by this symbol indicates compliance with the Essential Requirements of
the EMC Directive of the European Union 2014/30/EU.
This equipment meets the following conformance standards:
Safety
EN 60065: 2014 (T-Mark License),
IEC 60065: 2014 (CB Scheme Report/Certificate)
Additional licenses issued for specific countries available on request.
Emissions
EN 55032: 2012, CISPR 32: 2015,
EN 61000-3-2: 2014, EN 61000-3-3: 2013
Immunity
EN 55103-2: 2009, EN 61000-4-2:2009, EN 61000-4-3: 2006 + A1:2008 + A2:2010,
EN 61000-4-4: 2004 + A1:2010, EN 61000-4-5:2006, EN 61000-4-6:2009,
EN 61000-4-11:2004
Environments: E2, E3 and E4
The product is also licensed for additional country specific standards as required
for the International Marketplace.
Warning! This is a Class A product. In a domestic environment, this product
may cause radio interference, in which case, the user may be required to take
appropriate measures.
Achtung! Dieses ist ein Gerät der Funkstörgrenzwertklasse A. In Wohnbereichen
können bei Betrieb dieses Gerätes Rundfunkstörungen auftreten, in welchen
Fällen der Benutzer für entsprechende Gegenmaßnahmen verantwortlich ist.
Attention! Ceci est un produit de Classe A. Dans un environnement domestique,
ce produit risque de créer des interférences radioélectriques, il appartiendra
alors à l?utilisateur de prendre les mesures spécifiques appropriées..
Recycling Notice
This symbol on the product or its packaging indicates that this product
must not be disposed of with your other household waste. Instead, it is your
responsibility to dispose of your waste equipment by handing it over to a
designated collection point for the recycling of waste electrical and electronic
equipment. The separate collection and recycling of your waste equipment
at the time of disposal will help conserve natural resources and ensure that
it is recycled in a manner that protects human health and the environment.
For more information about where you can drop off your waste for recycling,
please contact your local authority, or where you purchased your product.
OG-3G-AMA openGear Card v1.0
30
www.aja.com

Korea KCC Compliance Statement
A급 기기
(업무용 방송통신기자재)
이 기기는 업무용(A급) 전자파적합기기로서 판매자 또는 사용자는
이 점을 주의하시기 바라며, 가정외의 지역에서 사용하는 것을
목적으로 합니다.
Class A
(Broadcasting Communication
Equipment for Office Use)
As an electromagnetic wave equipment for office use (Class A),
this equipment is intended to use in other than home area.
Sellers or users need to take note of this.
Taiwan Compliance Statement
This is a Class A product based on the standard of the Bureau of Standards,
Metrology and Inspection (BSMI) CNS 13438, Class A. In a domestic environment
this product may cause radio interference in which case the user may be required
to take adequate measures.
Japan Compliance Statement
This is a Class A product based on the standard of the VCCI Council (VCCI 32: 2016).
If this equipment is used in a domestic environment, radio interference may
occur, in which case, the user may be required to take corrective actions.
Translated Warning and Caution Messages
The following caution statements, warning conventions, and warning messages
apply to this product and manual.
OG-3G-AMA openGear Card v1.0
31
www.aja.com

Before Operation Please Read These Instructions
Warning! Read and follow all warning notices and instructions marked on the
product or included in the documentation.
Avertissement! Lisez et conformez-vous à tous les avis et instructions
d'avertissement indiqués sur le produit ou dans la documentation.
Warnung! Lesen und befolgen Sie die Warnhinweise und Anweisungen, die auf
dem Produkt angebracht oder in der Dokumentation enthalten sind.
¡Advertencia! Lea y siga todas las instrucciones y advertencias marcadas en el
producto o incluidas en la documentación.
Aviso! Leia e siga todos os avisos e instruções assinalados no produto ou incluídos
na documentação.
Avviso! Leggere e seguire tutti gli avvisi e le istruzioni presenti sul prodotto o
inclusi nella documentazione.
Warning! Do not use this device near water and clean only with a dry cloth.
Avertissement! N'utilisez pas cet appareil près de l'eau et nettoyez-le seulement
avec un tissu sec.
Warnung! Das Gerät nicht in der Nähe von Wasser verwenden und nur mit einem
trockenen Tuch säubern.
¡Advertencia! No utilice este dispositivo cerca del agua y límpielo solamente con
un paño seco.
Aviso! Não utilize este dispositivo perto da água e limpe-o somente com um pano
seco.
Avviso! Non utilizzare questo dispositivo vicino all'acqua e pulirlo soltanto con un
panno asciutto.
Warning! Do not block any ventilation openings. Install in accordance with the
manufacturer's instructions.
Avertissement! Ne bloquez aucune ouverture de ventilation. Suivez les
instructions du fabricant lors de l'installation.
Warnung! Die Lüftungsöffnungen dürfen nicht blockiert werden. Nur gemäß den
Anweisungen des Herstellers installieren.
¡Advertencia! No bloquee ninguna de las aberturas de la ventilación. Instale de
acuerdo con las instrucciones del fabricante.
Aviso! Não obstrua nenhuma das aberturas de ventilação. Instale de acordo com as
instruções do fabricante.
Avviso! Non ostruire le aperture di ventilazione. Installare in conformità con le
istruzioni del fornitore.
Warning! Do not install near any heat sources such as radiators, heat registers,
stoves, or other apparatus (including amplifiers) that produce heat.
Avertissement! N'installez pas l'appareil près d'une source de chaleur telle que des
radiateurs, des bouches d'air de chauffage, des fourneaux ou d'autres appareils
(amplificateurs compris) qui produisent de la chaleur.
Warnung! Nicht in der Nähe von Wärmequellen wie Heizkörpern, Heizregistern,
Öfen oder anderen Wärme erzeugenden Geräten (einschließlich Verstärkern)
aufstellen.
¡Advertencia! No instale cerca de fuentes de calor tales como radiadores, registros
de calor, estufas u otros aparatos (incluidos amplificadores) que generan calor.
Aviso! Não instale perto de nenhuma fonte de calor tal como radiadores, saídas de
calor, fogões ou outros aparelhos (incluindo amplificadores) que produzam calor.
Avviso! Non installare vicino a fonti di calore come termosifoni, diffusori di aria
calda, stufe o altri apparecchi (amplificatori compresi) che emettono calore
OG-3G-AMA openGear Card v1.0
32
www.aja.com

Warning! Do not defeat the safety purpose of the polarized or groundingtype plug. A polarized plug has two blades with one wider than the other. A
grounding type plug has two blades and a third grounding prong. The wide
blade or the third prong are provided for your safety. If the provided plug does
not fit into your outlet, consult an electrician for replacement of the obsolete
outlet.
Avertissement! La sécurité de la prise polarisée ou de la prise de type mise à la
terre ne doit en aucun cas être empêchée de fonctionner. Une prise polarisée
a deux broches, l'une étant plus large que l'autre. Une prise de type mise à la
terre a deux broches et une troisième broche pour la mise à la terre. La broche
large ou la troisième broche sont fournies pour votre sécurité. Si la prise
fournie ne s'insère pas dans votre prise femelle, consultez un électricien pour le
remplacement de la prise femelle obsolète.
Warnung! Der Sicherheitszweck des gepolten bzw. Schukosteckers ist zu
berücksichtigen. Ein gepolter Stecker verfügt über zwei Pole, von denen einer
breiter als der andere ist. Ein Schukostecker verfügt neben den zwei Polen noch
über einen dritten Pol zur Erdung. Der breite Pol bzw. der Erdungspol dienen der
Sicherheit. Wenn der zur Verfügung gestellte Stecker nicht in Ihren Anschluss
passt, konsultieren Sie einen Elektriker, um den veralteten Anschluss zu ersetzen.
¡Advertencia! No eche por tierra la finalidad del tipo de enchufe polarizado con
conexión a tierra. Un enchufe polarizado tiene dos espigas, una más ancha
que la otra. Un enchufe con conexión a tierra tiene dos espigas iguales y una
tercera espiga que sirve para la conexión a tierra. La expiga ancha, o la tercera
espiga, sirven para su seguridad. Si el enchufe suministrado no encaja en el
tomacorriente, consulte con un electricista para reemplazar el tomacorriente
obsoleto.
Aviso! Não anule a finalidade da segurança da ficha polarizada ou do tipo ligação
terra. Uma ficha polarizada tem duas lâminas sendo uma mais larga do que
a outra. Uma ficha do tipo de ligação à terra tem duas lâminas e um terceiro
terminal de ligação à terra. A lâmina larga ou o terceiro terminal são fornecidos
para sua segurança. Se a ficha fornecida não couber na sua tomada, consulte um
electricista para a substituição da tomada obsoleta.
Avviso! Non compromettere la sicurezza della spina polarizzata o con messa a
terra. Una spina polarizzata ha due spinotti, di cui uno più largo. Una spina con
messa a terra ha due spinotti e un terzo polo per la messa a terra. Lo spinotto
largo o il terzo polo sono forniti per motivi di sicurezza. Se la spina fornita non
si inserisce nella presa di corrente, contattare un elettricista per la sostituzione
della presa obsoleta.
Warning! Since the Mains plug is used as the disconnection for the device, it must
remain readily accessible and operable.
Avertissement! Puisque la prise principale est utilisée pour débrancher l'appareil,
elle doit rester aisément accessible et fonctionnelle.
Warnung! Da der Netzstecker als Trennvorrichtung dient, muss er stets zugänglich
und funktionsfähig sein.
¡Advertencia! Puesto que el enchufe de la red eléctrica se utiliza como dispositivo
de desconexión, debe seguir siendo fácilmente accesible y operable.
Aviso! Dado que a ficha principal é utilizada como a desconexão para o dispositivo,
esta deve manter-se prontamente acessível e funcional.
Avviso! Poiché il cavo di alimentazione viene usato come dispositivo di
sconnessione, deve rimane prontamente accessibile e operabile.
OG-3G-AMA openGear Card v1.0
33
www.aja.com

Warning! Protect the power cord from being walked on or pinched particularly at
plugs, convenience receptacles, and the point where they exit from the device.
Avertissement! Protégez le cordon d'alimentation pour que l'on ne marche
pas dessus ou qu'on le pince, en particulier au niveau des prises mâles, des
réceptacles de convenance, et à l'endroit où il sort de l'appareil.
Warnung! Vermeiden Sie, dass auf das Netzkabel getreten oder das Kabel geknickt
wird, insbesondere an den Steckern, den Steckdosen und am Kabelausgang am
Gerät.
¡Advertencia! Proteja el cable de energía para que no se le pise ni apriete, en
especial cerca del enchufe, los receptáculos de conveniencia y el punto del que
salen del equipo.
Aviso! Proteja o cabo de alimentação de ser pisado ou de ser comprimido
particularmente nas fichas, em tomadas de parede de conveniência e no ponto
de onde sai do dispositivo.
Avviso! Proteggere il cavo di alimentazione in modo che nessuno ci cammini sopra
e che non venga schiacciato soprattutto in corrispondenza delle spine e del
punto in cui esce dal dispositivo.
Warning! Unplug this device during lightning storms or when unused for long
periods of time.
Avertissement! Débranchez cet appareil pendant les orages avec éclairsou s'il est
inutilisé pendant de longues périodes.
Warnung! Das Gerät ist bei Gewitterstürmen oder wenn es über lange Zeiträume
ungenutzt bleibt vom Netz zu trennen.
¡Advertencia! Desenchufe este dispositivo durante tormentas eléctricas o cuando
no se lo utilice por largos periodos del tiempo.
Aviso! Desconecte este dispositivo da tomada durante trovoadas ou quando não é
utilizado durante longos períodos de tempo.
Avviso! Utilizzare soltanto i collegamenti e gli accessori specificati e/o venduti dal
produttore, quali il treppiedi e l'esoscheletro.
OG-3G-AMA openGear Card v1.0
34
www.aja.com

Warning! Refer all servicing to qualified service personnel. Servicing is required
when the device has been damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects have fallen into the device,
the device has been exposed to rain or moisture, does not operate normally, or
has been dropped.
Avertissement! Référez-vous au personnel de service qualifié pour tout entretien.
L'entretien est exigé quand l'appareil a été endommagé de quelque manière
que ce soit, par exemple lorsque le cordon d'alimentation ou la prise sont
endommagés, que du liquide a été versé ou des objets sont tombés dans
l'appareil, que l'appareil a été exposé à la pluie ou à l'humidité, ne fonctionne pas
normalement ou est tombé.
Warnung! Das Gerät sollte nur von qualifizierten Fachkräften gewartet werden.
Eine Wartung ist fällig, wenn das Gerät in irgendeiner Weise beschädigt wurde,
wie bei beschädigtem Netzkabel oder Netzstecker, falls Flüssigkeiten oder
Objekte in das Gerät gelangen, das Gerät Regen oder Feuchtigkeit ausgesetzt
wurde, nicht ordnungsgemäß funktioniert oder fallen gelassen wurde.
¡Advertencia! Consulte al personal calificado por cuestiones de reparación. El
servicio de reparación se requiere cuando el dispositivo ha recibido cualquier
tipo de daño, por ejemplo cable o espigas dañadas, se ha derramado líquido o
se han caído objetos dentro del dispositivo, el dispositivo ha sido expuesto a la
lluvia o humedad, o no funciona de modo normal, o se ha caído.
Aviso! Remeta todos os serviços de manutenção para o pessoal de assistência
qualificado. A prestação de serviços de manutenção é exigida quando o
dispositivo foi danificado mediante qualquer forma, como um cabo de
alimentação ou ficha que se encontra danificado/a, quando foi derramado líquido
ou caíram objectos sobre o dispositivo, quando o dispositivo foi exposto à chuva
ou à humidade, quando não funciona normalmente ou quando foi deixado cair.
Avviso! Fare riferimento al personale qualificato per tutti gli interventi di assistenza.
L'assistenza è necessaria quando il dispositivo è stato danneggiato in qualche
modo, ad esempio se il cavo di alimentazione o la spina sono danneggiati, è
stato rovesciato del liquido è stato rovesciato o qualche oggetto è caduto nel
dispositivo, il dispositivo è stato esposto a pioggia o umidità, non funziona
correttamente o è caduto
Warning! Do not open the chassis. There are no user-serviceable parts inside.
Opening the chassis will void the warranty unless performed by an AJA service
center or licensed facility.
Avertissement! Ne pas ouvrir le châssis. Aucun élément à l’intérieur du châssis
ne peut être réparé par l’utilisateur. La garantie sera annulée si le châssis est
ouvert par toute autre personne qu’un technicien d’un centre de service ou d’un
établissement agréé AJA.
Warnung! Öffnen Sie das Gehäuse nicht. Keine der Geräteteile können vom
Benutzer gewartet werden. Durch das Öffnen des Gehäuses wird die Garantie
hinfällig, es sei denn, solche Wartungsarbeiten werden in einem AJA-ServiceCenter oder einem lizenzierten Betrieb vorgenommen.
¡Advertencia! No abra el chasis. El interior no contiene piezas reparables por el
usuario. El abrir el chasis anulará la garantía a menos que se lo haga en un centro
de servicio AJA o en un local autorizado.
Advertência! Não abra o chassi. Não há internamente nenhuma peça que permita
manutenção pelo usuário. Abrir o chassi anula a garantia, a menos que a abertura
seja realizada por uma central de serviços da AJA ou por um local autorizado.
Avvertenza! Non aprire lo chassis. All’interno non ci sono parti riparabili
dall’utente. L’apertura dello chassis invaliderà la garanzia se non viene effettuata
da un centro ufficiale o autorizzato AJA.
OG-3G-AMA openGear Card v1.0
35
www.aja.com

Warning! Disconnect the external AC power supply line cord(s) from the mains
power before moving the unit.
Avertissement! Retirez le ou les cordons d’alimentation en CA de la source
d’alimentation principale lorsque vous déplacez l’appareil.
Warnung! Trennen Sie die Wechselstrom-Versorgungskabel vom Netzstrom, bevor
Sie das Gerät verschieben.
¡Advertencia! Cuando mueva la unidad desenchufe de la red eléctrica el/los
cable(s) de la fuente de alimentación CA tipo brick.
Advertência! Remova os cabos CA de alimentação brick da rede elétrica ao mover
a unidade.
Avvertenza! Scollegare il cavo dell’alimentatore quando si sposta l’unità.
Warning! Only use attachments and accessories specified and/or sold by the
manufacturer.
Avertissement! Utilisez seulement les attaches et accessoires spécifiés et/ou
vendus par le fabricant.
Warnung! Verwenden Sie nur Zusatzgeräte und Zubehör angegeben und / oder
verkauft wurde durch den Hersteller.
¡Advertencia! Utilice solamente los accesorios y conexiones especificados y/o
vendidos por el fabricante.
Aviso! Utilize apenas equipamentos/acessórios especificados e/ou vendidos pelo
fabricante.
Avviso! Utilizzare soltanto i collegamenti e gli accessori specificati e/o venduti dal
produttore.
Hazard! High Voltage. This situation or condition can cause injury due to electric
shock.
Avertissement! Tension élevée. Cette situation ou condition peut causer des
blessures dues à un choc électrique.
Warnung! Hochspannung. Diese Situation oder Bedingung kann zu Verletzungen
durch Stromschlag führen.
¡Advertencia! Alto voltaje . Esta situación o condición puede causar lesiones
debidas a una descarga eléctrica.
Aviso! Alta Tensão . Esta situação ou condição pode causar danos devido a
choques elétricos.
Avviso! Alta tensione. Questa situazione o condizione può causare lesioni a causa
di scosse elettriche.
Caution! To meet safety regulations for leakage current, connect the dual power
supplies to separate branch circuits.
¡Advertencia! Para cumplir con las normas de seguridad para la corriente de fuga,
conecte las dos fuentes de alimentación para circuitos derivados diferentes.
Attention! Pour répondre aux mesures de sécurité concernant le courant de
fuite, raccorder les sources d'alimentation doubles à des circuits de dérivation
distincts.
Warnung! Zur Erfüllung der Sicherheitsbestimmungen bezüglich Reststrom
schließen Sie bitte die zwei Netzteile an unterschiedlichen Abzweigleitungen an.
Cuidado! Para atender aos regulamentos de segurança para correntes de fuga,
conecte as fontes duplas a circuitos elétricos separados.
Attenzione! Per soddisfare le norme di sicurezza sulla corrente di perdita,
collegare i doppi alimentatori a circuiti derivati separati.
OG-3G-AMA openGear Card v1.0
36
www.aja.com

Warning! Ensure Mains Power is disconnected before installing the OG-3G-AMA
modules into the frame, or installing and removing options. If a Mains switch
is not provided, the power cord(s) of this equipment provide the means of
disconnection. The socket outlet must be installed near the equipment and must
be easily accessible.
Avertissement ! Avant d'installer des modules OG-3-FR dans la structure, ainsi
qu'avant d'installer ou d'enlever des options, assurez-vous d'avoir déconnecté
l'alimentation électrique. S'il n'y a pas d'interrupteur électrique, il faut
débrancher les câbles électriques de l'équipement. La prise électrique doit être
située à proximité de l'équipement et doit être aisément accessible.
Achtung! Sicherstellen, dass die Netzleitung entkoppelt ist, bevor die OG-3-FR
Module in das Gestell eingebaut oder Wahlteile eingebaut bzw. ausgebaut
werden. Wenn kein Netzschalter vorgesehen ist, dient das bzw. dienen die
Netzkabel dieser Vorrichtung als Entkopplungsmittel. Die Steckdose muss in der
Nähe der Vorrichtung installiert und leicht zugänglich sein.
Avvertenza. Accertarsi che l'alimentazione di rete sia scollegata prima di installare
i moduli OG-3-FR nel frame o di installare e rimuovere componenti opzionali. Se
non è presente un interruttore di accensione/spegnimento, occorre scollegare
il cavo (o i cavi) di alimentazione di questo apparecchio dalla presa di corrente.
La presa di corrente deve essere situata presso l'apparecchio e facilmente
accessibile.
Aviso! Certifique-se que a fonte principal de energia elétrica está desconectada
antes de instalar os módulos OG-3-FR no bastidor ou antes de instalar e remover
opções. Se o interruptor principal não existir, o cabo elétrico deste equipamento
proporciona o meio de desconexão. A tomada elétrica deverá ser instalada perto
do equipamento e deverá ser de fácil acesso.
¡Advertencia! Asegúrese que la red de alimentación está desconectada antes
de instalar los módulos OG-3-FR en el marco, o la instalación y extracción de
opciones. Si no se proporciona un conmutador de red, el cable de alimentación
de este equipo proporciona los medios de desconexión. El zócalo tomacorriente
debe estar instalado cerca del equipo y debe ser fácilmente accesible.
Warning! Dual Power Cord Notice—please read this. To reduce the risk of electrical
shock, disconnect both power cords before servicing equipment.
Avertissement ! Avis concernant la double alimentation électrique—à lire
soigneusement. Pour éviter tout risque d'électrocution, débranchez les deux
câbles électriques avant d'intervenir sur l'équipement.
Achtung! Hinweis auf Doppel-Netzkabel-bitte lesen. Um das Risiko eines
Elektroschocks zu verringern, müssen beide Netzkabel ausgestöpselt werden,
bevor die Vorrichtung gewartet wird.
Avvertenza. Avviso concernente il cavo di alimentazione doppio - leggere
attentamente. Per ridurre il rischio di elettrocuzione, scollegare entrambi i cavi
di alimentazione prima di eseguire la manutenzione o riparazioni di questo
apparecchio.
Aviso! Aviso de Cabo Elétrico Duplo - por favor, leia isto. Para reduzir o risco
de choque elétrico, desconecte ambos os cabos elétricos antes de fazer
manutenção ao equipamento.
¡Advertencia! Aviso del doble cable de alimentación - leer esto por favor.
Para reducir el riesgo de descarga eléctrica, desconecte ambos cables de
alimentación antes de dar servicio al equipo.
Caution! The OG-3G-AMA front fan door is heavy. Remove with Caution.
Attention! La porte du ventilateur avant OG- 3 - FR est lourd. Retirer avec
précaution.
Achtung! Die OG -3- FR -Frontlüfter Tür ist schwer. Bitte vorsichtig entfernen.
¡Precaución! LLa puerta del ventilador frontal OG- 3 -FR es pesado. Extraer con
precaución.
Atenção! A porta do ventilador frontal OG -3- FR é pesado. Remova com cuidado.
Attenzione! La porta ventola anteriore OG -3 - FR è pesante. Rimuovere con
cautela.
OG-3G-AMA openGear Card v1.0
37
www.aja.com

Warranty and Liability Information
AJA VIDEO SYSTEMS, INC.
Limited Warranty on Hardware
AJA Video Systems, Inc. (AJA Video) warrants that the hardware product, not
including storage modules or software components, will be free from defects in
materials and workmanship for a period of five (5) years from the date of purchase.
AJA Video warrants that the storage modules provided as part of the hardware
product will be free from defects in materials and workmanship for a period of one
year from the date of purchase. AJA Video provides a separate software warranty as
part of the license agreement applicable to software components.
If a hardware product or storage module (hereafter, a “product”) proves to be
defective during the applicable warranty period, AJA Video, at its option, will either
repair the defective product without charge for parts and labor, or will provide a
replacement in exchange for the defective product.
To obtain service under this warranty, the Customer must notify AJA Video of the
defect before expiration of the warranty period and make suitable arrangements for
the performance of service by contacting AJA Video support through the channels
set forth on the support contacts web page at http://www.aja.com/support. Except
as stated, the Customer shall bear all shipping, packing, insurance and other costs,
excluding parts and labor, to effectuate repair. Customer shall pack and ship the
defective product to a service center designated by AJA Video, with shipping charges
prepaid. AJA Video shall pay to return the product to Customer but only if to a
location within the country in which the AJA Video service center is located.
This warranty shall not apply to any defect, failure or damage caused by negligent,
inadequate or improper use, handling or maintenance. Without limiting the
foregoing, AJA Video shall not be obligated to furnish service under this warranty
or repair any damage or malfunction a) resulting from attempts by personnel other
than AJA Video representatives to install, repair or service the product, b) resulting
from improper use or connection to incompatible equipment, c) caused by the use
of non-AJA Video parts or supplies, d) if the product has been modified or integrated
with other products when the effect of such a modification or integration increases
the time or difficulty of servicing the product, or e) resulting from being dropped
or otherwise subjected to undue force, exposure to moisture or other corrosive or
conductive substances, exposure to strong magnetic fields, use with improperly
regulated power supplies, exposure to electric shock, use in temperatures outside the
specified operating range, or otherwise failing to treat the product in accordance with
the standard of care appropriate to sensitive and delicate electronic equipment.
EXCEPT AS STATED ABOVE, AJA VIDEO AND ITS VENDORS DISCLAIM IN THEIR
ENTIRETY ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT
LIMITATION ALL WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE. AJA VIDEO’S RESPONSIBILITY TO REPAIR OR REPLACE TIMELY REPORTED
DEFECTIVE PRODUCTS IS THE WHOLE AND EXCLUSIVE REMEDY CUSTOMER IS
PROVIDED WITH RESPECT TO HARDWARE PRODUCTS AND THEIR STORAGE MODULES.
SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OF IMPLIED WARRANTIES OR
LIMITATIONS ON APPLICABLE STATUTORY RIGHTS OF A CONSUMER, SO SOME OR ALL
OF THE TERMS OF THIS PARAGRAPH MAY NOT APPLY TO YOU.
THE PRODUCT IS NOT INTENDED, STATED, OR WARRANTED TO OPERATE
UNINTERRUPTED OR ERROR-FREE. YOU UNDERSTAND AND ACKNOWLEDGE THAT THE
PRODUCT IS NOT INTENDED TO BE USED AS THE SOLE OR PRIMARY DATA SOURCE OR
TARGET FOR CRITICAL DATA, AND THAT IT IS YOUR RESPONSIBILITY TO IMPLEMENT
REDUNDANT CAPTURE AND BACKUP SYSTEMS AS APPROPRIATE.
OG-3G-AMA openGear Card v1.0
38
www.aja.com

Limitation of Liability
Under no circumstances shall AJA video BE LIABLE IN ANY WAY FOR ANY LOST,
CORRUPTED OR DESTROYED DATA, FOOTAGE OR WORK, OR FOR ANY OTHER
INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LOST PROFITS,
OR FOR ANY THIRD PARTY CLAIM, IN CONNECTION WITH THE PRODUCT, WHETHER
RESULTING FROM DEFECTS IN THE PRODUCT, SOFTWARE OR HARDWARE FAILURE,
OR ANY OTHER CAUSE WHATSOEVER, EVEN IF AJA VIDEO HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES. AJA VIDEO’S LIABILITY IN CONNECTION WITH THE
PRODUCT SHALL UNDER NO CIRCUMSTANCES EXCEED THE PURCHASE PRICE PAID
FOR THE PRODUCT. The foregoing limitations apply even if any remedy set forth in
this LIMITED WARRANTY fails of its essential purpose. SOME JURISDICTIONS DO NOT
ALLOW THE LIMITATION OF LIABILITY FOR PERSONAL INJURY, OR OF INCIDENTAL OR
CONSEQUENTIAL DAMAGES, SO SOME OR ALL OF THE TERMS OF THIS PARAGRAPH
MAY NOT APPLY TO YOU.
Governing Law and Language; Your Rights.
This limited warranty is the only warranty provided by AJA Video on the hardware
product. It supersedes all prior or contemporaneous understandings regarding such
subject matter. No amendment to or modification of this warranty will be binding
unless in writing and signed by AJA Video. The laws of the State of California, USA
will govern this warranty and any dispute arising from it. Any translation of this
Agreement is intended for convenience and to meet local requirements and in the
event of a dispute between the English and any non-English versions, the English
version of this warranty will govern. This limited warranty gives you specific legal
rights and you may have other rights that vary from jurisdiction to jurisdiction, some
of which are noted above.
OG-3G-AMA openGear Card v1.0
39
www.aja.com

Index
A
AJA Support 2
Analog Audio Inputs
Embed to 21
Analog Audio Outputs
Disembed from 22
D
DashBoard Control System 6
Analog Audio Level 23
Audio 1 Tab Screen 21
Audio 2 Tab Screen 22
documentation 13
downloading 13
Packet Processing Control 22
Rebooting 25
Requirements 13
Setup Tab Screen 23
Uploading New Software 24
Use Cases 14
Using 13
Default Operational Settings 11
DIP Switches 6, 11
Description of Settings 12
Settings 11
F
I
Features 4
Installation 6
Cabling 9
Front Card Installation 8
Rear Card Installation 7
WECO audio mating connectors 9
I/O Connections 5
O
openGear and AJA 5
Operation 11
Overview 4
S
T
Safety and Compliance 29
Technical Specifications 27
Technical Support 2
U
User Controls 5
OG-3G-AMA openGear Card v1.0
40
www.aja.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement