Earthquake ™ Earth Auger Powerhead Operator's Manual

Operator's Manual Original Operating Instructions

Two-Man Earth Auger Powerhead 9800 Series

Get parts online at

www.getearthquake.com

Includes models: 9800B 9800H 9800BCE (European)

GAS/OIL RATIO 50:1

P/N: OM9800B ECN: 9695 REV4: 01/03/13 © 2013 Ardisam, Inc.

All Rights Reserved

2 Operator's Manual

Two-Man Earth Auger Powerhead 9800 Series

INTRODUCTION

Congratulations on your investment in quality. Thank you for purchasing an Earthquake™ Two-Man Auger Powerhead. We have worked to ensure that this powerhead meets the highest standards for usability and durability. With proper care, this powerhead will provide many years of service.

Please read this entire manual before installation and use. Earthquake reserves the right to change, alter or improve the product and this document at any time without prior notice.

CONTENTS

Introduction/Contents/Registration .........................................................................................................................................................................................2 Warnings and Safety Precautions ...........................................................................................................................................................................................3-7 Features ...............................................................................................................................................................................................................................................7 Assembly .............................................................................................................................................................................................................................................8 Operation ......................................................................................................................................................................................................................................9-10 Maintenance and Storage ....................................................................................................................................................................................................11-12 Troubleshooting and Repair ................................................................................................................................................................................................12-13 Parts Breakdown ......................................................................................................................................................................................................................14-17 Warranty ............................................................................................................................................................................................................................................18

CE Declaration of Conformity ....................................................................................................................................................................................................19

REGISTRATION, SERVICE AND MAINTENANCE LOG

Record the model number and serial number in the space provided for easy reference. Warranty is valid only if the completed regis tration is received by Earthquake within 30 days of purchase. You can register your warranty online by visiting www.getearthquake.

com. If you do not have a computer, call our customer service department at (800) 345-6007 Mondays through Fridays from 8 a.m. to 5 p.m. CST.

OWNERSHIP RECORDS

Owner’s Name: Owner’s Address: City: Model Number: Date of Purchase: Notes: State/Province: Serial Number: Zip Code/Postal Code:

This manual may contain information for several models. Read and keep this manual for future reference. This manual con tains important information on SAFETY, ASSEMBLY, OPERATION, AND MAINTENANCE. The owner must be certain that all the product information is included with the unit. This information includes the MANUAL, the REPLACEMENT PARTS and the WAR RANTIES. This information must be included to make sure state laws and other laws are followed. This manual should remain with the engine even if it is resold.

Check for parts online at

www.getearthquake.com

or call 800-345-6007 M-F 8-5

Operator's Manual

Two-Man Earth Auger Powerhead 9800 Series

WARNINGS AND SAFETY PRECAUTIONS

OPERATOR'S RESPONSIBILITY

Accurate assembly and safe and effective use of the machine is the operator's responsibility.

• Read and follow all safety instructions.

• Carefully follow all assembly instructions.

• Maintain the machine according to directions and schedule included in this operator’s manual.

• Ensure that anyone who uses the machine is familiar with all controls and safety precautions.

SPECIAL SAFETY MESSAGES

Your manual contains special messages to bring attention to potential safety concerns, machine damage as well as helpful operating and servicing information. Please read all the infor mation carefully to avoid injury and machine damage.

NOTE: General information is given throughout the manual that may help the operator in the operation or service of the machine.

This symbol points out important safety instruc tions which if not followed could endanger your personal safety.

BEFORE OPERATING ENGINE:

WARNING READ ENTIRE OPERATING AND MAINTENANCE INSTRUCTIONS FOR THIS PRODUCT AND THE INSTRUCTIONS FOR THE ENGINE THAT POWERS THIS UNIT. FAILURE TO FOLLOW INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. OPERATE THE ENGINE ACCORDING TO THE SAFETY INSTRUCTIONS OUTLINED HERE AND INSERTED THROUGHOUT THE TEXT. ANYONE WHO USES THIS PRODUCT MUST READ THE INSTRUCTIONS AND BE FAMILIAR WITH THE CONTROLS.

WARNING

WARNING INDICATES A HAZARD WHICH, IF NOT AVOIDED, COULD RESULT IN DEATH OR SERIOUS IN JURY AND/OR PROPERTY DAMAGE.

CAUTION CAUTION INDICATES YOU CAN BE HURT OR YOUR EQUIPMENT DAMAGED IF THE SAFETY INSTRUC TIONS THAT FOLLOW THIS SIGNAL WORD ARE NOT OBEYED.

IMPORTANT INDICATES HELPFUL INFORMATION FOR PROPER AS SEMBLY, OPERATION, OR MAINTENANCE OF YOUR EQUIPMENT.

WARNING CALIFORNIA PROPOSITION 65 WARNING ENGINE EXHAUST FROM THIS PRODUCT CONTAINS CHEMICALS KNOWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER, BIRTH DEFECTS, OR OTHER RE PRODUCTIVE HARM.

WARNING YOU MUST READ, UNDERSTAND AND COMPLY WITH ALL SAFETY AND OPERATING INSTRUCTIONS IN THIS MANUAL BEFORE ATTEMPTING TO SETUP AND OPERATE YOUR MACHINE.

FAILURE TO COMPLY WITH ALL SAFETY AND OPERATING INSTRUCTIONS CAN RESULT IN LOSS OF MACHINE CONTROL, SERIOUS PERSONAL INJURY TO YOU AND/OR BYSTANDERS, AND RISK OF EQUIPMENT AND PROPERTY DAMAGE. THE TRIANGLE IN THE TEXT SIGNIFIES IMPORTANT CAUTIONS OR WARNINGS WHICH MUST BE FOLLOWED.

Intended Use / Foreseeable Misuse

This is a motorized earth auger that drills into soil. It is pedes trian controlled. It has a petrol-fuelled internal combustion en gine that powers the auger blades. It shall not be used for any other purpose. Check for parts online at

www.getearthquake.com

or call 800-345-6007 M-F 8-5 3

Operator's Manual

Two-Man Earth Auger Powerhead 9800 Series

• • • • • •

GENERAL SAFETY RULES

• • • • • • • • • Read, understand, and follow all instructions on the machine and in the manual(s). Be thoroughly familiar with the controls and the proper use of the machine before starting. Use this equipment for its intended purpose only.

Familiarize yourself with all of the safety and operating decals on this equipment and on any of its attachments or accessories.

Do not put hands or feet near or under rotating parts.

Only allow responsible individuals who are familiar with the instructions to operate the machine. Do not allow children to operate this machine. Do not allow adults to operate the machine without proper instruction.

Thoroughly inspect the area where the machine is to be used and remove all foreign objects. Your equipment can propel small objects at high speed causing personal injury or property damage. Stay away from breakable objects, such as house windows, automobile, greenhouses, etc. Wear appropriate clothing such as a long-sleeved shirt or jacket. Also wear long trousers or slacks. Do not wear shorts. Never wear sandals, sneakers, or open shoes, and never operate the machine with bare feet. Do not wear loose clothing or jewelry. They can get caught in moving parts. Always keep hands, feet, hair and loose clothing away from any moving parts on engine and machine.

Always wear safety goggles or safety glasses with side shields when operating the machine to protect your eyes from foreign objects which can be thrown from the unit. Always wear a protective hearing device.

Always wear work gloves and sturdy footwear. Wear footwear that will improve footing on slippery surfaces. Leather work shoes or short boots work well for most people. These will protect the operator’s ankles and shins from small sticks, splinters, and other debris.

It is advisable to wear protective headgear to prevent the possibility of being struck by small flying particles, or being struck by low hanging branches, twigs, or other objects which may be unnoticed by the operator.

Do not operate the machine without proper guards or other safety protective devices in place.

See manufacturer’s instructions for proper operation and installation of accessories. Only use accessories approved by the manufacturer.

Operate only in daylight or good artificial light.

Do not operate product when fatigued or under the influence of alcohol, drugs or other medication which can cause drowsiness or affect your ability to operate this machine safely. • • • • • • • • • • Watch for traffic when operating near, or when crossing roads.

If the equipment should start to vibrate abnormally, stop the engine (motor), disconnect the spark plug wire and prevent it from touching the spark plug. Check immediately for cause. Vibration is generally a warning of trouble. If the noise or vibrations of the machine increase, stop immediately and perform an inspection.

Never leave the machine unattended when the engine is running. Regularly inspect the machine. Make sure parts are not bent, damaged or loose. Temperature of muffler and nearby areas may exceed 150° F (65° C). Allow muffler and engine areas to cool before touching. Never pick up or carry the machine while the engine is running. Prolonged exposure to noise and vibration from gasoline engine powered equipment should be avoided. Take intermittent breaks and/or wear ear protection from engine noise as well as heavy work gloves to reduce vibration in the hands.

Keep all screws, nuts and bolts tight.

Do not transport the machine from one place to another with the engine running.

When moving the packaged machine, always do so with a partner.

Check local regulations for age restrictions on use of this machine.

PRODUCT-SPECIFIC SAFETY RULES

• • • • • • Do not drill above underground utilities, including water lines, gas lines, electric cables, or pipes. Do not operate the auger in soil with large rocks and foreign objects which can damage the equipment.

After striking a foreign object, stop the engine. Remove the wire from the spark plug. Inspect the auger for damage. If damaged, repair before starting and operating the auger.

The blades of the auger should not rotate when the engine is idling. If it does rotate when engine is idling, contact customer service for instructions.

If an object becomes lodged in the auger, turn engine off, remove the wire from the spark plug and secure, allow to cool before attempting to remove the foreign object.

The earth blade is very sharp. Use extreme caution when drilling a hole or replacing the blade.

Do not carry the earth auger unit between holes with the engine running. 4 Check for parts online at

www.getearthquake.com

or call 800-345-6007 M-F 8-5

Operator's Manual

Two-Man Earth Auger Powerhead 9800 Series

ENGINE SAFETY PRECAUTIONS

Warning Carbon Monoxide Poisoning Engines give off carbon monoxide, an odorless, colorless, poison gas. Carbon monoxide may be present even if you do not smell or see any engine exhaust. Breathing carbon monoxide can cause nausea, fainting or death, in addition to drowsiness, dizziness and confusion. If you experience any of these symptoms, seek fresh air and medical attention immediately. If your product comes with a separate engine manual, be sure to read and follow all safety and warning precautions outlined there, in addition to any in this manual.

Preventing Carbon Monoxide Poisoning

• Always start and run engine outdoors. Do not start or run engine in an enclosed area, even if doors or windows are open. • Never try to ventilate engine exhaust indoors. Carbon monoxide can reach dangerous levels very quickly.

• Never run engine outdoors where exhaust fumes may be pulled into a building.

• Never run engine outdoors in a poorly ventilated area where the exhaust fumes may be trapped and not easily taken away. (Examples include: in a large hole or areas where hills surround your working area.) • Never run engine in an enclosed or partially enclosed area. (Examples include: buildings that are enclosed on one or more sides, under tents, car ports or basements.) • Always run the engine with the exhaust and muffler pointed in the direction away from the operator.

• Never point the exhaust muffler towards anyone. Bystanders should always be many feet away from the operation of the engine and its attachments.

• Do not change the engine governor settings or over-speed the engine.

Gasoline Fires and Handling Fuel Safely

Use extra care in handling gasoline and other fuels. They are flammable and vapors are explosive.

• • • When storing extra fuel be sure that it is in an appropriate container and away from any fire hazards.

Prevent fire and explosion caused by static electric discharge. Use only nonmetal, portable fuel containers approved by the Underwriter’s Laboratory (U.L.) or the American Society for Testing & Materials (ASTM).

Always fill fuel tank outside in a well ventilated area. Never fill your fuel tank with fuel indoors. (Examples include: basement, garage, barn, shed, house, porch, etc.) Never fill tank near appliances with pilot lights, heaters, or other

WARNING ENGINES GIVE OFF CARBON MONOXIDE, AN ODOR LESS, COLORLESS, POISON GAS. CARBON MONOXIDE MAY BE PRESENT EVEN IF YOU DO NOT SMELL OR SEE ANY ENGINE EXHAUST. BREATHING CARBON MON OXIDE CAN CAUSE NAUSEA, FAINTING OR DEATH, IN ADDITION TO DROWSINESS, DIZZINESS AND CONFU SION. IF YOU EXPERIENCE ANY OF THESE SYMPTOMS, SEEK FRESH AIR AND MEDICAL ATTENTION IMMEDIATELY.

• • • • • • • •

CAUTION HOT GASES ARE A NORMAL BY-PRODUCT OF A FUNC TIONING CATALYTIC CONVERTER. FOLLOW ALL SAFE TY INSTRUCTIONS TO PREVENT BURNS AND FIRES.

DO NOT ALTER/MODIFY ENGINE: NEVER ALTER OR MODIFY THE ENGINE FROM THE FACTORY. SERIOUS INJURY OR DEATH MAY OCCUR IF ENGINE IS MODIFIED OR ALTERED.

WHEN WORKING ON OR REPLACING PARTS FOR THE ENGINE OR PRODUCT, YOU MUST ALWAYS DISCON NECT SPARK PLUG WIRE FROM THE SPARK PLUG AND KEEP IT AWAY FROM THE SPARK PLUG.

ignition sources. If the fuel has to be drained, this should be done outdoors. The drained fuel should be stored in a container specifically designed for fuel storage or it should be disposed of carefully.

Never remove the fuel cap or add fuel with the engine running. Stop engine and allow to cool before filling.

Never drain fuel from engine in an enclosed area.

Always wipe up excess (spilled) fuel from engine before starting. Clean up spilled fuel immediately. If fuel is spilled, do not start the engine but move product and fuel container from area. Clean up spilled fuel and allow to evaporate and dry after wiping and before starting.

Allow fuel fumes/vapors to escape from the area before starting engine.

Test the fuel cap for proper installation before starting and using engine. Always run the engine with fuel cap properly installed on the engine.

Always unscrew gas cap vent screw while engine is running.

Never smoke while refilling engine fuel tank or while operating the unit.

Check for parts online at

www.getearthquake.com

or call 800-345-6007 M-F 8-5 5

Operator's Manual

Two-Man Earth Auger Powerhead 9800 Series

• • • • • • • Do not store engine with fuel in fuel tank indoors. Fuel and fuel vapors are highly explosive. During storage, screw down gas cap vent screw tightly if equipped.

Never pour fuel from engine fuel tank. Never siphon fuel by mouth to drain fuel tank.

Always have an adult fill the fuel tank and never allow children to fill the engine.

Never allow an adult or anyone under the influence of drugs or alcohol to fill engine.

When storing gasoline or equipment with fuel in the tank, store away from furnaces, stoves, water heaters or other appliances that have a pilot light or other ignition source because they can ignite gasoline vapors.

BURNS AND FIRES

The muffler, muffler guard and other parts of the engine be come extremely hot during the operation of the engine. These parts remain extremely hot after the engine has stopped.

Prevention of Burns and Fires

• Never remove the muffler guard from the engine.

• Never touch the muffler guard because it is extremely hot and will cause severe burns.

• Never touch parts of the engine that become hot after operation.

• Always keep materials and debris away from muffler guard and other hot parts of the engine to avoid fires.

CHILDREN AND BYSTANDERS

Tragic accidents can occur if the operator is not alert to the presence of children and/or bystanders. Never assume that others will remain where you last saw them.

SERVICE

• Always stop the engine whenever you leave the equipment, before cleaning, repairing or inspecting the unit. Engine should be turned off and cool, spark plug wire must be removed from spark plug before any repairs or adjustments are attempted. Never make adjustments or repairs with the engine (motor) running. Disconnect the spark plug wire, and keep the wire away from the plug to prevent accidental starting. Remove the ignition key if equipped with an electric start. • Always wear eye protection when you make adjustments or repairs.

• Keep all nuts and bolts tight and keep equipment in good condition. • Never tamper with safety devices. Check their proper operation regularly.

• When servicing or repairing the machine, do not tip the machine over or up unless specifically instructed to do so in this manual. Service and repair procedures can be done with the machine in an upright position. Some procedures will be easier if the machine is lifted on a raised platform or working surface.

• To reduce fire hazard, keep machine free of grass, leaves, or other debris build-up. Clean up oil or fuel spillage. Allow machine to cool before storing.

• Stop and inspect the equipment if you strike an object. Repair, if necessary, before restarting. • Clean and replace safety and instruction decals as necessary.

• To guard against engine over-heating, always have engine debris filter mounted and clean.

• Inspect machine before storage. When not in use, disconnect spark plug lead and store indoors in a dry place locked or otherwise inaccessible to children.

• Use only original equipment parts from Earthquake, including all nuts and bolts.

• Keep the area of operation clean of all persons, especially small children and pets. Keep children under the watchful care of a responsible adult. • Be alert and turn machine off if children enter the area.

• Before and while moving backwards, look behind and down for small children.

• Never allow children to operate the machine. 6 Check for parts online at

www.getearthquake.com

or call 800-345-6007 M-F 8-5

Operator's Manual

Two-Man Earth Auger Powerhead 9800 Series

SAFETY DECALS (9800BCE EUROPEAN MODELS ONLY)

This auger unit has been designed and manufactured to provide you with the safety and reliability you would expect from an industry leader in outdoor power equipment manufacturing.

Company: Ardisam Part No: Description: Type: Revision: Born: ECN No: 10497 Decal 1 10-27-11 Company: Ardisam Part No: Description: Type: Revision: Born: 10501 ARTWORK NOISE LEVEL 9800BCE Decal 1 10-27-11 Although reading this manual and the safety instructions it contains will provide you with the necessary basic knowledge to oper ated this equipment safely and effectively, we have placed several safety labels on the powerhead to remind you of this important information while you are operating the unit.

regarding their meaning or how to comply with these instructions, reread the complete safety instruction text on the preceding pages, or contact your local dealer.

Part No: 10507 Revision: Born: Description: ECN No: Ardisam 1 Artist: ECN No: Artist: Should any of the safety labels become unreadable because of being worn, faded, or otherwise damaged during the use of your Type: Decal Artist: 10-27-11 Scott Andrew Waldal Revision: Born: 1 10-27-11 ECN No: Artist: Scott Andrew Waldal Colors Used: Pantone Process Black IMPORTANT: Colors Used:

ARDISAM, INC.

1160 8th Avenue | Cumberland, WI 54829 | USA Serial No.

Model:

9800BCE

Type:

Earth Auger

Year:

2012

Mass:

50.72 kg

Max. Operating Speed:

121 rpm

L PA (dBA):

94.4

L WA (dBA):

102.7

Part No. 10498 SERIAL NUMBER LOCATION DECAL

Colors Used:

Part No. 10502 HOT SURFACE DECAL 102.7

Part No. 10508 NOISE LEVEL DECAL Part No. 10505 SAFETY PRECAUTIONS DECAL - Read entire manual before operating product - Wear eye and hearing protection - Throttle speed control

Pantone Process Black Colors Used:

FEATURES (9800B/9800BCE SHOWN)

IMPORTANT: Please slit backing material to ensure ease of removal.

Pantone Process Black Pantone Process Yellow starter handle oil fill IMPORTANT: Please slit backing material to ensure ease of removal.

choke lever fuel cap Pantone Process Black Pantone Process Yellow IMPORTANT: Please slit backing material to ensure ease of removal.

fuel shut off valve muffler spark plug ON/OFF switch primer bulb throttle control air filter Check for parts online at

www.getearthquake.com

or call 800-345-6007 M-F 8-5 7

Operator's Manual

Two-Man Earth Auger Powerhead 9800 Series

ASSEMBLY

UNPACK POWERHEAD

1. Carefully lift the powerhead out of the box, remove any packing material and cut any ties.

TOOLS REQUIRED

• Two (2) 9/16” Wrenches

ASSEMBLY INSTRUCTIONS (SEE FIGURE 1)

1. Insert the output shaft of the transmission in the open end of the Flex Coil Shock Top.

2. Line up the bolt holes through the Flex Coil Shock Top and the output shaft of the transmission.

3. Place the included 3/8-16 x 1.5 inch bolt through the bolt hole.

4. Hand-thread the 3/8-16 “Bi-way” locknut on the bolt.

5. Using two 9/16 inch wrenches, securely tighten the nut and bolt.

transmission output shaft 3/8-16 bi-way locknut 3/8-16 x 1.5 inch bolt flex coil shock top

FIGURE 1

8 Check for parts online at

www.getearthquake.com

or call 800-345-6007 M-F 8-5

Operator's Manual

Two-Man Earth Auger Powerhead 9800 Series

OPERATION

PRE-START CHECKLIST

1. Read and understand the operator's manual that came with your unit and the engine.

2. Fill oil sump or check oil level. Check oil level often during engine break-in.

3. Fill fuel tank. Use unleaded, regular gasoline.

4. Be sure spark plug wire is attached to spark plug.

PREPARING ENGINE FOR STARTING

TO CHECK THE OIL

1. Check the engine oil level with the engine stopped and in a level position.

2. Remove the oil filler cap/dipstick and wipe it clean.

3. Insert the oil filler cap/dipstick into the oil filler neck, but do not screw it in; then remove it to check the oil level.

4. If the oil level is near or below the lower limit mark on the dipstick, fill with the recommended oil to the upper limit mark. Do not overfill.

5. Reinstall the oil filler cap/dipstick.

FUEL RECOMMENDATIONS

Use clean, fresh, regular unleaded gasoline with a minimum of 85 octane.

• These engines are certified to operate on unleaded gasoline. Unleaded gasoline produces fewer engine and spark plug deposits and extends exhaust system life. • Never use stale or contaminated gasoline or an oil/gasoline mixture. Avoid getting dirt or water in the fuel tank. • Occasionally, you may hear a light ‘‘spark knock’’ or ‘‘pinging’’ (metallic rapping noise) while operating under heavy loads. This is no cause for concern. • If spark knock or pinging occurs at a steady engine speed, under a normal load, change gasoline brands. If spark knock or pinging persists, see an authorized servicing dealer.

CAUTION

DO NOT START YOUR EARTH AUGER UNIT UNTIL YOU HAVE READ THE ENGINE MANUAL THAT CAME WITH YOUR ENGINE, AND THE "WARNINGS AND SAFETY PRECAUTIONS" SECTION IN THIS MANUAL. IF YOU HAVE READ THESE, FOLLOW THE STEPS TO START YOUR EARTH AUGER UNIT. ALWAYS PERFORM PRE-START CHECKLIST BEFORE STARTING THE ENGINE.

IT IS RECOMMENDED THAT THE EARTH AUGER UNIT NOT BE TILTED AT MORE THAN A 30 DEGREE ANGLE FROM THE UPRIGHT POSITION. FAILURE TO DO SO CAN CAUSE FUEL AND/OR OIL LEAKAGE.

CAUTION

NEVER ADD GAS WHEN ENGINE IS RUNNING OR HOT FROM OPERATION. NEVER FILL THE TANK INDOORS. DO NOT SMOKE WHEN FILLING FUEL TANK.

NEVER FILL FUEL TANK COMPLETELY. FILL TANK TO 1/2" BELOW BOTTOM OF FILLER NECK TO PROVIDE SPACE FOR FUEL EXPANSION. WIPE ANY FUEL SPILLAGE FROM ENGINE AND EQUIPMENT BEFORE STARTING ENGINE.

DO NOT HOLD THROTTLE LEVER WIDE OPEN WHILE STARTING. LOSS OF CONTROL OF POWERHEAD/AUGER COULD RESULT.

NEVER RUN ENGINE INDOORS OR IN ENCLOSED, POORLY VENTILATED AREAS. ENGINE EXHAUST CONTAINS CARBON MONOXIDE, AN ODORLESS AND DEADLY GAS.

KEEP HANDS, FEET, HAIR AND LOOSE CLOTHING AWAY FROM ANY MOVING PARTS ON ENGINE AND EQUIPMENT.

TEMPERATURE OF MUFFLER AND NEARBY AREAS MAY EXCEED 150° F. AVOID THESE AREAS.

BEFORE STORING UNIT, DISCONNECT SPARK PLUG WIRE FROM SPARK PLUG AND ATTACH IT TO RETAINING POST.

NEVER STORE ENGINE WITH FUEL IN TANK INDOORS OR IN ENCLOSED, POORLY VENTILATED AREAS, WHERE FUEL FUMES MAY REACH AN OPEN FLAME, SPARK OR PILOT LIGHT.

IMPORTANT

NEVER MIX OIL WITH GASOLINE.

Check for parts online at

www.getearthquake.com

or call 800-345-6007 M-F 8-5 9

Operator's Manual

Two-Man Earth Auger Powerhead 9800 Series FILLING FUEL TANK

1. Shut-off engine and allow engine to completely cool before refilling the gas tank.

2. Move to a well-ventilated area, outdoors, away from flames and sparks.

3. Clean debris from area around the gas cap.

4. Loosen gas cap slowly. Place the cap on a clean, dry surface.

5. Carefully add fuel without spilling.

6. Do not fill gas tank completely full; allow space for fuel to expand.

7. Immediately replace gas cap and tighten. Wipe off spilled fuel and allow to dry before starting engine.

IMPORTANT OPERATION NOTES

1. Read engine manual and follow instructions for fuel type, starting, etc.

2. The clutch will transfer maximum power after about two hours of normal operation. During this break-in period clutch slippage may occur. The clutch should be kept free of oil or other moisture for efficient operation. 3. The earth auger unit should be operated no more than 20 degrees in any direction during continuous use, and limited to 30 degrees intermittently. This is recommended for adequate lubrication and fuel delivery.

4. When digging in heavy soil, lift the earth auger unit out of the hole once for every one foot of depth.

5. Never run engine indoors. Exhaust fumes are deadly.

6. Do not use an earth auger in ice.

7. Drill holes without placing excessive body weight on the unit. The auger operates most efficiently with a shaving action caused by the weight of the unit itself.

STARTING AND STOPPING ENGINE

TO START ENGINE:

1. Open fuel shut-off valve.

2. Flip the on/off switch to ON position.

3. Move choke lever to the CHOKE position.

NOTE: Do not use the choke to restart a warm engine after a short shut down.

4. Grasp starter handle and pull rope out, slowly, until it pulls slightly harder. Let rope rewind slowly. Then pull rope with a rapid full arm stroke. Let rope return to starter slowly.

5. When engine fires or starts running, gradually move the choke lever back to the RUN position.

TO STOP ENGINE:

1. Flip the on/off switch to the OFF position.

2. Close fuel shut-off valve.

10

WARNING MAKE SURE THE UNIT IS IN A STABLE POSITION BE FORE PULLING THE STARTER HANDLE. WHEN THE UNIT STARTS TO FIRE OR RUN, RELEASE THE THROTTLE CONTROL MOMENTARILY WITH YOUR RIGHT HAND AND RETURN YOUR LEFT HAND TO THE HANDLEBAR POSITION TO MAINTAIN CONTROL AND STABILITY OF THE UNIT WITH BOTH HANDS. CAUTION ALWAYS HANDLE FUEL IN A WELL VENTILATED AREA, OUTDOORS, AWAY FROM FLAMES OR SPARKS. DO NOT START ENGINE IF FUEL IS SPILLED. WIPE OFF EXCESS FUEL AND ALLOW TO DRY. REMOVE ENGINE FROM AREA TO AVOID SPARKS.

TO PREVENT ACCIDENTAL STARTING: ENGINE MUST BE TURNED OFF AND COOL, AND SPARK PLUG WIRE MUST BE REMOVED FROM SPARK PLUG BEFORE CHECKING AND ADJUSTING ENGINE OR EQUIPMENT.

DO NOT OPERATE AUGER BEFORE READING THE ENGINE MANUAL PROVIDED IN THE PARTS PACKET.

ALWAYS WEAR A PROTECTIVE HEARING DEVICE.

IF AUGER IS MOUNTED TO ENGINE, ALL SAFETY GUARDS MUST BE SECURELY ON TO AVOID SERIOUS INJURY.

STARTER ROPE CAN CAUSE AN UNANTICIPATED JERK TOWARDS ENGINE. PLEASE FOLLOW INSTRUCTIONS TO AVOID INJURY.

IF ENGINE FAILS TO START AFTER PERFORMING THE STARTING PROCEDURES, PLEASE CONTACT OUR CUSTOMER SERVICE DEPARTMENT AT 800-345-6007.

NEVER LEAVE ENGINE RUNNING WHILE UNATTEND ED. TURN OFF AFTER EVERY USE.

NEVER CARRY POWERHEAD AND AUGER BETWEEN HOLES WHILE ENGINE IS RUNNING.

IMPORTANT

ENGINE CAN OVERHEAT AND BECOME DAMAGED IF DE BRIS BLOCKS THE COOLING FINS OR RECOIL HOUSING.

NEVER RUN ENGINE WITHOUT COMPLETE AIR CLEAN ER INSTALLED ON ENGINE.

Check for parts online at

www.getearthquake.com

or call 800-345-6007 M-F 8-5

Operator's Manual

Two-Man Earth Auger Powerhead 9800 Series

MAINTENANCE AND STORAGE

POWER AUGER MAINTENANCE

1. The gear case has 4 oz. of grease installed at the factory. It is recommended that once a year the gear case be split and the grease level checked. Add grease only if level of grease is below top of the gears. DO NOT OVERFILL. 2. Keep all screws, nuts, and bolts tight.

3. For cold weather operation, store the unit in a cool environ ment. Transferring the unit from a warm to a cold place can cause the build up of harmful condensation.

4. If blade performance decreases, turn unit off and disconnect spark plug wire. Carefully inspect cutting edge of blade for any signs of wear. If blades show any of these signs, they need to be sharpened or replaced.

5. Always allow muffler to cool before filling fuel tank.

6. When storing for over one month, use gas stabilizer in fuel.

7. Do not fill gas tank indoors or when engine is running or is hot.

ENGINE MAINTENANCE

Please read your engine manual and observe these recommen dations to extend the life of your engine. Your engine manual provides detailed information and a maintenance schedule for performing the following tasks: 1. Check oil level every five (5) operating hours and before each use.

2. Change oil after first two (2) operating hours and every 25 operating hours thereafter, more often if operated in extremely dusty or dirty conditions. Change oil while engine is still warm from recent running.

3. Frequently remove dirt and debris from cooling fins, air intake screen, levers and linkage. This will help ensure adequate cooling and correct engine speed.

4. Check air cleaner.

5. Check spark plug yearly or every 100 operating hours.

6. Check engine and auger often for loose nuts and bolts.

Good maintenance is essential for safe, economical, and trou ble-free operation. It will also help reduce air pollution. To help you properly care for your engine, read your engine manual and pay close attention to the maintenance schedule, routine inspection procedures, and simple maintenance procedures.

Other service tasks that are more difficult, or require special tools, are best handled by professionals and are normally per formed by a technician or other qualified mechanic.

CAUTION TO PREVENT ACCIDENTAL STARTING: ENGINE MUST BE TURNED OFF AND COOL, AND SPARK PLUG WIRE MUST BE REMOVED FROM SPARK PLUG BEFORE CHECKING AND ADJUSTING ENGINE OR EQUIPMENT.

CHECK AUGER OFTEN FOR LOOSE NUTS AND BOLTS. KEEP THESE ITEMS TIGHTENED.

NEVER STORE ENGINE WITH FUEL IN THE TANK IN SIDE A BUILDING. POTENTIAL SPARKS MAY BE PRES ENT FOR IGNITION OF FUEL AND FUEL VAPORS.

ANY MAINTENANCE AND REPAIR ON THE ENGINE AND AUGER MUST ALWAYS BE DONE BY AN ADULT.

ENGINE MUST BE SHUT-OFF, COOL, AND SPARK PLUG WIRE REMOVED BEFORE ANY REPAIR OR MAINTE NANCE CAN BE DONE.

Maintenance, replacement or repair of the emissions control devices and systems may be performed by any non-road engine repair establishment or individuals. However, items must be serviced by an authorized dealer to obtain "no charge" emissions control service.

The maintenance schedule applies to normal operating condi tions. If you operate your engine under unusual conditions, such as sustained high-load or high-temperature operation, or use in unusually wet or dusty conditions, consult your servic ing dealer for recommendations applicable to your individual needs and use.

TRANSPORTING YOUR EARTH AUGER

1. Never transport engine inside an enclosed space or vehicle. Fuel or fuel vapors may ignite causing serious injury or death.

2. If fuel is present in the fuel tank, transport in an open vehicle in an upright position.

3. If an enclosed vehicle must be used, remove gas into an ap proved red fuel container. DO NOT siphon by mouth. 4. Run engine to use up the fuel in the carburetor and fuel tank. Always run engine in a well ventilated area.

5. Wipe away any spilled fuel from engine and earth auger. Allow to dry.

Check for parts online at

www.getearthquake.com

or call 800-345-6007 M-F 8-5 11

Operator's Manual

Two-Man Earth Auger Powerhead 9800 Series

LONG-TERM STORAGE

If your earth auger will not be used for more than one month, prepare it for long-term storage.

Follow the steps below to prepare your earth auger unit for storage. Read your engine manual for detailed instructions on preparing the engine for storage.

1. Run with gas stabilizer in fuel. The screen in the carburetor will glaze shut if gas stabilizer is not used before storage.

2. Drain the fuel system. Run the engine until it stops.

3. Change oil.

4. Remove spark plug, pour one (1) ounce of clean engine oil into spark plug hole. Cover hole with a rag. Pull starter handle slowly several times to distribute oil. Install spark plug. Do not

connect spark plug wire.

5. Clean entire earth auger unit.

6. Store your earth auger unit in a clean, dry building that is inaccessible to children.

TROUBLESHOOTING AND REPAIR

At Earthquake, we build quality and durability into the design of our products; but no amount of careful design by us, and careful maintenance by you, can guarantee a repair-free life for your Earthquake powerhead. Most repairs will be minor, and easily fixed by following the suggestions in the troubleshooting guide in this manual.

The troubleshooting guide will help you pinpoint the causes of common problems and identify remedies.

For more complicated repairs, you may want to rely on your retailer, an authorized service center or Earthquake. A parts breakdown is located toward the end of this manual.

We will always be glad to answer any questions you have, or help you find suitable assistance. To order parts or inquire about warranty, call or e-mail us using the contact information found under "Ordering Replacement Parts".

CAUTION TO AVOID INJURY OR DEATH, NEVER SIPHON FUEL BY MOUTH.

NEVER STORE EARTH AUGER WITH FUEL IN THE GAS TANK INSIDE AN ENCLOSED AREA OR BUILDING.

MAINTENANCE AND REPAIR ON THE ENGINE AND AU GER MUST ALWAYS BE DONE BY AN ADULT.

ENGINE MUST BE SHUT-OFF, COOL, AND SPARK PLUG WIRE REMOVED BEFORE ANY REPAIR OR MAINTE NANCE CAN BE DONE.

CAUTION DO NOT STORE EARTH AUGER UNIT WITH FUEL IN TANK INDOORS OR IN ENCLOSED, POORLY VENTILATED AREAS, WHERE FUEL FUMES MAY REACH AN OPEN FLAME, SPARK, PILOT LIGHT OR AN IGNITED OBJECT. DRAIN FUEL OUTDOORS AWAY FROM ANY IGNITION SOURCES. USE ONLY APPROVED FUEL CONTAINERS.

FOR LONG TERM STORAGE: CLOSE FUEL SHUT-OFF VALVE AND STORE EARTH AUGER UNIT IN AN UPRIGHT POSITION. FAILURE TO DO SO CAN CAUSE OIL LEAKAGE OVER A PROLONGED PERIOD.

ORDERING REPLACEMENT PARTS

Parts can be obtained from the store where the auger was purchased or direct from the factory. To order parts visit www.

getearthquake.com or call 1-800-345-6007. For other general questions, you can e-mail us at info@getearth quake.com.

IN CASE OF A SERVICE PROBLEM, DO NOT SEND EARTH AUGER UNIT BACK TO RETAILER. CONTACT EARTHQUAKE AT 800-345-6007.

Please include the following information with your order: 1) Part numbers 2) Part description 3) Quantity 4) Model number and serial number 12 Check for parts online at

www.getearthquake.com

or call 800-345-6007 M-F 8-5

Operator's Manual

Two-Man Earth Auger Powerhead 9800 Series

TROUBLESHOOTING GUIDE

While normal care and routine maintenance will extend the life of your auger powerhead, prolonged or constant use may even tually require that service be performed to allow it to continue operating properly. The troubleshooting guide below lists the most common problems, causes and remedies.

CAUTION PRACTICE SAFETY AT ALL TIMES. ENGINE MUST BE TURNED OFF AND ALLOWED TO COOL, AND SPARK PLUG WIRE MUST BE DISCONNECTED BEFORE ATTEMPTING ANY MAINTENANCE OR REPAIR.

PROBLEM

Engine will not start

POSSIBLE CAUSE

1. Power switch off 2. Spark plug wire disconnected 3. Fuel valve closed 1. Dirty air cleaner

REMEDY/ACTION

1. Flip switch to ON position 2. Connect spark plug wire to spark plug 3. Open fuel valve 1. Clean or replace air cleaner Engine runs rough, floods during operation Engine is hard to start Engine misses or lacks power Auger turns at idle Auger turns, but has no power Auger cuts slowly Engine runs, then quits 2. Carburetor out of adjustment 3. Fuel valve closed 1. Stale fuel 2. Spark plug wire loose 3. Dirty carburetor 1. Clogged fuel tank 2. Broken clutch spring 1. Carburetor out of adjustment 2. Broken transmission 3. Worn clutch shoes 4. Worn engine lower seal 1. Damaged point 2. Worn out blade 1. Screen in carburetor plugged 2. Fuel valve closed 2. Take to authorized Briggs & Stratton/Honda service center 3. Open fuel valve 1. Drain old fuel and replace with fresh. Use gas stabi lizer at end of season 2. Make sure spark wire is securely attached to spark plug 3. Clean carburetor, use gas stabilizer, new gas can 1. Remove and clean 2. Clogged air cleaner 3. Improper carburetor adjustment 4. Spark plug dirty, improper gap, or wrong type 1. Idle speed too high 2. Clean or replace 3. Take to authorized Briggs & Stratton/Honda service center 4. Replace spark plug and adjust gap 1. Adjust idle speed lower 2. Replace both springs 1. Take to authorized Briggs & Stratton/Honda service center 2. Replace transmission 3. Replace clutch 4. Take to authorized Briggs & Stratton / Honda ser vice center 1. Replace fishtail point 2. Replace blade 1. Clean screen, use gas stabilizer, clean gas can 2. Open fuel valve

NOTE: Please see the engine manual for any engine issues.

Check for parts online at

www.getearthquake.com

or call 800-345-6007 M-F 8-5 13

PARTS BREAKDOWN

9800B/9800BCE/9800H MAIN PARTS EXPLOSION

Operator's Manual

Two-Man Earth Auger Powerhead 9800 Series

1 7 6 8 5 9 3 12 13 2 11 10 11 11 4 14

KEY NO.

1 5 6 2 3 4

PART NO.

513 513CE

DESCRIPTION

ENGINE, BRIGGS 675 SERIES ENGINE, BRIGGS 675 SERIES CE GCV160 9819 9827 HANDLE AND THROTTLE GRIP 9800 9800BTRANKIT TRANSMISSION ASSEMBLY 30:1 (9800B/9800BCE ONLY) 98005 9837A TRANSMISSION ASSEMBLY 30:1 (9800H ONLY) MOUNT RING COMPLETE 9800 SERIES 9825 ENGINE 160CC HONDA WELDMENT, FRAME 9800 ROTOR CENTRIFUGAL CLUTCH

QTY.

1 1 1 1 4 1 1 1 1

KEY NO.

7 8 9 10 11

PART NO.

WK6 - 420 503 9801 12 13 4819 9805A 504 60G56

DESCRIPTION

KEY WOODRUFF 5/32 X 5/8 SET SCREW 1/4-20 X 1/4 SCPC BLK OXIDED BOLT 5/16-24 X 3/4 PFCS BOLT 5/16-18 X 1-1/2 HH CABLE THROTTLE W/TRIGGER 9800B/9800BCE ONLY TRIGGER ASSEMBLY (NO CABLE, 9800H ONLY) CABLE (NO TRIGGER, 9800H ONLY) LOCKWASHER SPRING 5/16 INCH NUT 5/16-18 BI-WAY LOCK GR5 ZN

QTY.

1 1 4 8 1 1 1 8 8 Check for parts online at

www.getearthquake.com

or call 800-345-6007 M-F 8-5

Operator's Manual

Two-Man Earth Auger Powerhead 9800 Series

9800B/9800BCE/9800H TRANSMISSION PARTS EXPLOSION

KEY NO.

1 2

PART NO.

75600* 8915 16 13 3 4 8919 8922 12 9 4 8 5 6 11 2 7 5 6 7 8 9 10 11 12 13 14 15 16 8923 8924 9214A 75300** 8912 8913 8914 9814 9018 8929 8935 3004149

DESCRIPTION

KIT LOWER CASTING DOWEL PIN STEEL 1/4 INCH X 1/2 INCH GASKET-POWERHEAD TRANSMISSION BEARING BALL R12 DOUBLE LIP SEALED 3/4 IN. I.D.

BEARING BALL R10 OPEN 5/8 IN. I.D.

RING RETAINING EXTERNAL 3/4 INCH GEAR 10T CLUSTER PINION HT KIT TOP CASTING GEAR 44T 3/4 IN. HOLE SHAFT OUTPUT GEAR 48T HARD GEAR 7T PINION THREADED CLUTCH DRUM 3" THREADED SHORT BOLT 1/4-20 X 1-1/2 SHCS BOLT 1/4-20 X 2-1/2 SHCS F-T SHIM, 9800 TRANSMISSION TOP

QTY.

1 2 1 3 2 3 1 1 1 1 1 1 1 2 4 1 4 5 3 * The lower casting kit (P/N: 75600) includes: lower half gear box case, the powerhead transmission gasket (8919), and ball bearings (8922, 8923).

** The top casting kit (P/N: 75300) includes: gear case top (3004111), ball bearings (8922, 8933), shim (3004149) and gasket (8919).

1 4 15 10 14 Check for parts online at

www.getearthquake.com

or call 800-345-6007 M-F 8-5 15

AUGER PARTS EXPLOSIONS

EA2F, EA3F

8, 9 27

EA4F

10 27 Operator's Manual

Two-Man Earth Auger Powerhead 9800 Series EA6F

2 4 20 3 7 22 21 1 11 18 16 16 4 2

EA8F

6 3 20 12 7 22 21 1 2 1 21

EA10F

18 19 14 5 18 15 7 20 4 1 2 19 5

EA12F, EA14F

BALLOON # 1 2 3 8 9 6 7 4 5 10 11 12 13 14 PART # 21 154 8980 EB10A EBOLT 1423 WF516 60G56 ENUT 8958HD 1151 I10 1433 2104 LBB10P DESCRIPTION EARTH AUGER WELDMENT 10 IN RH SHOCK SPRING BLADE EARTH 10INCH CUT AND SHARPENED BOLT 1/4-28 X 5/8 HH GR5 ZN 7 WASHER FLAT 5/16 INCH STANDARD ZN NUT-LOC 5/16-18 BI-WAY ZN FISH TAIL POINT DECAL AND ART WARNING AUGER ICE AND EARTH INSERT 10 IN AUGER BOX NUT 3/8-16 HLKBW ZN ASSEMBLY BOX UPC STENCIL EA10F QTY.

1 1 1 2 1 2 2 2 2 1 2 1 1 1 13 23, 24 5 19 18 17 18 25, 26 19 19 5 5 Check for parts online at

www.getearthquake.com

or call 800-345-6007 M-F 8-5

AUGER PARTS LIST

KEY NO.

1 2 19 20 21 22 23 24 25 26 27 - - - 12 13 14 15 16 17 18 3 4 7 8 5 6 9 10 11 - - --

PART NO.

1423 1433 ENUT 2104 WF516 715 EA12F EA14F EB12 EB14 8955 53684 60G56 8958HD 8970 8980 EA2F EA3F EA4F EA6F EA8F EA10F EB4 EB6 EB8 EB10 EBOLT EXT12 EXT18 EB6HD EB8HD EB10HD 9811

DESCRIPTION

BOLT-HHCS, 5/16-18 X 2”, GRADE 5 (auger shock spring) BOLT-HHCS, 3/8-16 X 1-1/2” (auger to powerhead) SHOCK TOP 1-PC (used on 6” and 8" earth augers) NUT-HEX 2-WAY REVERSIBLE LOCKNUT, 5/16-18 FISHTAIL POINT (used on 4” or larger earth auger) EARTH POINT (used on 2” & 3” earth auger) SHOCK SPRING (Used on 6" and larger earth augers) EARTH AUGER, 2” W/FISHTAIL POINT EARTH AUGER, 3” W/FISHTAIL POINT EARTH AUGER, 4” W/FISHTAIL POINT EARTH AUGER, 6” W/FISHTAIL POINT EARTH AUGER, 8” W/FISHTAIL POINT EARTH AUGER, 10” W/FISHTAIL POINT EARTH BLADE, 4” (includes EBOLT & ENUT) EARTH BLADE, 6” (includes EBOLT & ENUT) EARTH BLADE, 8” (includes EBOLT & ENUT) EARTH BLADE, 10” (includes EBOLT & ENUT) BOLT-HEX, 1/4-28 X 5/8”, GRADE 5 (earth blade to auger) NUT-NYLOC, 1/4-28 NUT HEX LOCKING, 3/8-16 WASHER-FLAT, 5/16” SET SCREW 1/4-20 X 1/4 SCPC BLK OXIDED EARTH AUGER, 12” W/FISHTAIL POINT EARTH AUGER, 14" W/FISHTAIL POINT EARTH BLADE, 12” (includes EBOLT & ENUT) EARTH BLADE, 14” (includes EBOLT & ENUT) BOLT 3/8-16 X 1-1/4 SHCS

ITEMS NOT SHOWN

DEPTH EXTENSION, 12" DEPTH EXTENSION, 18" HEAVY DUTY EARTH BLADE, 6” (includes EBOLT & ENUT) HEAVY DUTY EARTH BLADE, 8” (includes EBOLT & ENUT) HEAVY DUTY EARTH BLADE, 10” (includes EBOLT & ENUT) SWITCH, ON/OFF (Not Shown)

QTY.

2 2 1 1 1 1 1 1 1 1 1 1 1 1 2 1 2 1 1 1 1 1 1 1 2 2 2 2 1 1 1 1 1 Operator's Manual

Two-Man Earth Auger Powerhead 9800 Series

Check for parts online at

www.getearthquake.com

or call 800-345-6007 M-F 8-5 17

Operator's Manual

Two-Man Earth Auger Powerhead 9800 Series

18

9800 SERIES EARTH AUGER POWERHEAD

Warranty Terms and Conditions

PRODUCT WARRANTY: 1-YEAR LIMITED WARRANTY

Ardisam, Inc., a manufacturing company, warrants this EARTHQUAKE™ EARTH AUGER POWERHEAD to be free from defects in the material or workmanship for a period of one year from the date of purchase. During the one year warranty of this product, Ardisam will furnish, at their discretion, parts and labor to correct any defect caused by faulty material or workmanship. Any unit used in a commercial application is covered for a period of 90 days after purchase. This warranty applies to the original owner with a proof of purchase and is not transferable. For the warranty to be valid, the product must be registered online, or the warranty card must be filled out and received by Ardisam, Inc., within 30 days of purchase.

*These warranties apply only to products which have not been subjected to negligent use, misuse, alteration, ac cident, unauthorized parts, failure to use proper fuel and oil, or if repairs have been performed at non-authorized service centers. These warranties supersede all other warranties either expressed or implied and all other obligations or liabilities on our part. Ardisam, does not assume, and does not authorize any other person to assume for us, any liability in connection with the sale of our products. To be at “No Charge,” warranty work must be sent directly to Ardisam, Inc. or one of our authorized service centers and performed by them. To obtain warranty service and/or replacement instructions, contact our customer service department. If you choose to ship your product to Ardisam for warranty repair, you must first have prior approval from Ardisam by calling our customer service department for a return material authorization number (RMA#). Under these circumstances, all items must be shipped prepaid. Ardisam will at no charge, repair or replace, at their discretion, any defective part which falls under the conditions stated above. Ardisam retains the right to change models, specifications and price without notice.

Earthquake™, Division of Ardisam, Inc.

1160 Eighth Avenue; P.O. Box 666 Cumberland, Wisconsin 54829 800-345-6007 · Fax (715) 822-4180 E-mail: [email protected]

Check for parts online at

www.getearthquake.com

or call 800-345-6007 M-F 8-5

Operator's Manual

Two-Man Earth Auger Powerhead 9800 Series

Check for parts online at

www.getearthquake.com

or call 800-345-6007 M-F 8-5 19

Earthquake™, Division of Ardisam, Inc.

1160 8th Avenue, PO Box 666 Cumberland, WI 54829 800-345-6007 | Fax 715-822-2223 E-mail: [email protected]

All weights, specifications and features are approximate and are subject to change without notice. Due to continuous product improvements, product images may not be exact. Items used for props not included. Some assembly may be required. Check for parts online at

www.getearthquake.com

or call 800-345-6007 M-F 8-5