Sennheiser e 845 Instruction Manual

Sennheiser e 845 Instruction Manual

e 845/e 845 S

Instruction manual

Delivery includes

• e 845 / e 845 S • MZQ 800 microphone clamp • pouch • quick guide • safety guide

Product overview

3 4 1 2 1. Sound inlet basket 2. XLR-3 connector 3. On/off switch (e 845 S only) 4. Screw (e 845 S only)

Delivery includes

e 845/e 845 S | 2/8

Installation

Attaching the microphone

Screw the microphone clamp to a stand.

Place the microphone with its back end into the microphone clamp.

Orient the microphone together with the microphone clamp.

Installation Connecting the microphone

Connect the XLR-3 socket of the microphone cable (optional accessories) to the XLR-3 socket of the microphone.

Using the windshield

Place the MZW 4032 (optional accessories) windshield over the microphone head.

e 845/e 845 S | 3/8

Operation

Operation

Holding the microphone

If you cover the microphone head during transmission, this will change the pick-up pattern of the microphone and consequently the sound.

Only hold the radio microphone by its body.

Positioning the microphone

It is vital to observe the following notes:

Position

A B C A

Resulting sound

High proximity effect (large bass boost) Powerful, direct sound Less proximity effect (less bass boost) Some room ambience, natural, balanced sound Very little proximity effect (minimal bass boost) More room ambience, indirect sound B C

Commentary

Very little crosstalk from other sound sources More crosstalk from other sound sources Higher crosstalk from other sound sources 5-10 cm >10 cm If sibilance occurs: Position the microphone slightly to the side and not directly in front of the mouth.

e 845/e 845 S | 4/8

Operation Positioning the monitor loudspeakers

To prevent feedback and crosstalk, postion your monitor loudspeakers in the angle area of the highest cancellation of the microphone (approx. 120°).

120°

Switching the e 845 S on/off

Use the on/off switch to switch the the e 845 S on or off.

If necessary, use the screw to lock the on/off switch in the „on“ position.

always

e 845/e 845 S | 5/8

Cleaning and maintaining the e 845 / e 845 S

Cleaning and maintaining the e 845 / e 845 S CAUTION

LIQUIDS CAN DAMAGE THE ELECTRONICS OF THE PRODUCT!

Liquids entering the housing of the product can cause a short-circuit and damage the electronics.

Keep all liquids away from the product.

Do not use any solvents or cleansing agents.

Disconnect the products from the power supply system and remove rechargeable batteries and batteries before you begin cleaning.

Clean all products only with a soft, dry cloth.

Cleaning the sound inlet basket of the microphone module

Unscrew the sound inlet basket.

Remove the foam insert from the sound inlet basket.

Use a slightly damp cloth to clean the sound inlet basket from the inside and ouside.

If necessary, clean the foam insert with a mild detergent or replace the foam insert.

Dry the foam insert.

Reinsert the foam insert.

Replace the sound inlet basket on the microphone head and screw it tight.

e 845/e 845 S | 6/8

Specifications

Transducer principle Frequency response Pick-up pattern Sensitivity (free field, no load) Nominal impedance (at 1 kHz) Min. terminating impedance Connector Temperature range Dimensions Weight

Polar pattern

90° 60° 30° 0° 0 5 10 15 20 25 dB 0° 30° 60° 90° dynamic 40 - 16,000 Hz super-cardioid 1.8 mV/Pa 350 Ω 1 kΩ XLR-3 0 °C to +40 °C ⌀ 46 x 185 mm 330 g 125 Hz 250 Hz 500 Hz 1,000 Hz 2,000 Hz 4,000 Hz 8,000 Hz 16,000 Hz 120° 150° 180°

Frequency response

dBV -40 -50 -60 -70 -80 -90 50 10 0 0°, 1 m 20 0 180° 150° 50 0 1,0 00 120° 2,0 00 5,0 00 10 ,00 0 20 ,00 0 Hz

Specifications

e 845/e 845 S | 7/8

Overview of applications Connector assignment

1 3 2 + XLR 1 3 2 + XLR 1 3 2 + XLR + 2 3 1 XLR + 6.3 mm +

UNBALANCED

6.3 mm +

BALANCED Overview of applications

Primary application Secondary application + 2 3 1 XLR e 902 e 904 e 906 e 908 e 914 e 935 e 945 e 965 e 602 II e 604 e 608 e 609 silver e 614 e 835 e 845 e 865 e 901 • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • e 845/e 845 S | 8/8

Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement