KTM 690 Enduro R EU 2012 Travel Bike Owner Manual

Add to my manuals
196 Pages

advertisement

KTM 690 Enduro R EU 2012 Travel Bike Owner Manual | Manualzz
OWNER'S MANUAL 2012
690 Enduro R EU
690 Enduro R AUS/UK
Art. no. 3211787en
DEAR KTM CUSTOMER
1
Congratulations on your decision to buy a KTM motorcycle. You are now the owner of a state-of-the-art sports motorcycle that will give you
enormous pleasure if you service and maintain it accordingly.
DEAR KTM CUSTOMER
We wish you a lot of enjoyment in riding this vehicle!
Enter the serial numbers of your vehicle below.
Chassis number (
p. 16)
Engine number (
p. 17)
Key number (
Dealer's stamp
p. 17)
The owner's manual corresponded to the latest state of this series at the time of printing. Slight deviations resulting from continuing development and design of our vehicles cannot, however, be completely excluded.
All specifications are non-binding. KTM Sportmotorcycle AG specifically reserves the right to modify or delete technical specifications,
prices, colors, forms, materials, services, designs, equipment, etc., without prior notice and without specifying reasons, to adapt these
to local conditions, as well as to stop production of a particular model without prior notice. KTM accepts no liability for delivery options,
deviations from illustrations and descriptions, as well as misprints and other errors. The models portrayed partly contain special equipment
that does not belong to the regular scope of delivery.
DEAR KTM CUSTOMER
© 2012 KTM-Sportmotorcycle AG, Mattighofen Austria
All rights reserved
Reproduction, even in part, as well as copying of all kinds, is permitted only with the express written permission of the copyright owner.
ISO 9001(12 100 6061)
According to the international quality management standard ISO 9001, KTM uses quality assurance processes that lead to
the maximum possible quality of the products.
Issued by: TÜV Management Service
KTM-Sportmotorcycle AG
5230 Mattighofen, Austria
2
TABLE OF CONTENTS
TABLE OF CONTENTS
MEANS OF REPRESENTATION ............................................... 7
IMPORTANT INFORMATION ................................................... 8
VIEW OF VEHICLE................................................................ 12
View of vehicle, front left (example).................................... 12
View of vehicle, rear right (example) ................................... 14
SERIAL NUMBERS............................................................... 16
Chassis number................................................................ 16
Type label........................................................................ 16
Engine number................................................................. 17
Key number ..................................................................... 17
Fork part number.............................................................. 18
Shock absorber part number.............................................. 18
CONTROLS .......................................................................... 19
Clutch lever ..................................................................... 19
Hand brake lever .............................................................. 19
Throttle grip..................................................................... 20
Light switch ..................................................................... 20
Turn signal switch ............................................................ 21
Horn button ..................................................................... 21
Emergency OFF switch...................................................... 22
Electric starter button ....................................................... 22
Ignition/steering lock ........................................................ 23
Combination instrument .................................................... 23
Combination instrument - function buttons ......................... 24
Combination instrument - indicator lamps........................... 24
Combination instrument - display....................................... 25
Combination instrument - speedometer............................... 26
Setting kilometers or miles ................................................ 26
Combination instrument - time .......................................... 27
3
Setting the clock ..............................................................
Combination instrument - display ODO ...............................
Combination instrument - setting/resetting TRIP 1...............
Combination instrument - setting/resetting TRIP 2...............
Combination instrument - TRIP F display............................
Combination instrument - coolant temperature indicator ......
Opening the filler cap .......................................................
Closing filler cap ..............................................................
Seat release .....................................................................
Handrails.........................................................................
Passenger footrests...........................................................
Shift lever........................................................................
Foot brake lever................................................................
Side stand .......................................................................
PREPARING FOR USE ..........................................................
Advice on first use ............................................................
Running in the engine.......................................................
Loading the vehicle ..........................................................
RIDING INSTRUCTIONS .......................................................
Performing checks and vehicle care when preparing for
use .................................................................................
Starting ...........................................................................
Starting off ......................................................................
Shifting, riding .................................................................
Braking ...........................................................................
Stopping, parking .............................................................
Refueling.........................................................................
SERVICE SCHEDULE............................................................
Service schedule ..............................................................
27
28
28
29
30
30
31
32
32
33
33
34
35
35
36
36
37
38
40
40
41
42
42
46
47
48
51
51
TABLE OF CONTENTS
4
TUNING THE CHASSIS.........................................................
Fork/shock absorber ..........................................................
Adjusting the compression damping of the fork ...................
Adjusting the rebound damping of the fork..........................
Compression damping of the shock absorber .......................
Adjusting the low-speed compression damping of the shock
absorber ..........................................................................
Adjusting the high-speed compression damping of the
shock absorber .................................................................
Adjusting the rebound damping of the shock absorber..........
Measuring the unloaded rear wheel sag...............................
Checking the static sag of the shock absorber .....................
Checking the riding sag of the shock absorber .....................
Adjusting the spring preload of the shock absorber
.........
Adjusting the riding sag
...............................................
Handlebar position ...........................................................
Adjusting handlebar position
........................................
SERVICE WORK ON THE CHASSIS ........................................
Raising the motorcycle with the lift stand ...........................
Removing the motorcycle from the lift stand .......................
Bleeding the fork legs .......................................................
Cleaning the dust boots of the fork legs ..............................
Loosening the fork protection.............................................
Positioning the fork protection ...........................................
Checking the steering head bearing play .............................
Adjusting the play of the steering head bearing
..............
Removing the seat ............................................................
Mounting the seat ............................................................
Removing the air filter
.................................................
x
x
x
x
x
54
54
54
55
56
56
57
58
59
60
61
61
63
64
64
66
66
66
67
67
68
69
69
70
72
72
73
Installing the air filter
.................................................. 74
Checking the chain for dirt ................................................ 75
Cleaning the chain............................................................ 75
Checking the chain tension ............................................... 76
Adjusting the chain tension ............................................... 77
Check the chain, rear sprocket, engine sprocket and chain
guide............................................................................... 79
Adjusting chain guide
.................................................. 84
Adjusting basic position of clutch lever............................... 85
Checking/rectifying the fluid level of the hydraulic clutch ..... 85
Removing the engine guard ............................................... 86
Installing the engine guard ................................................ 87
BRAKES .............................................................................. 88
Checking the free travel of the hand brake lever .................. 88
Adjusting the free travel of the hand brake lever .................. 88
Checking the brake discs................................................... 89
Checking the front brake fluid level .................................... 90
Adding front brake fluid
............................................... 91
Checking the front brake linings......................................... 92
Changing the front brake linings
................................... 93
Checking the free travel of foot brake lever.......................... 97
Adjusting the basic position of the foot brake lever
......... 97
Checking rear brake fluid level........................................... 98
Adding rear brake fluid
................................................ 99
Checking the rear brake linings ........................................ 101
Changing the rear brake linings
................................... 101
WHEELS, TIRES ................................................................ 105
Removing the front wheel
........................................... 105
Installing the front wheel
............................................ 106
x
x
x
x
x
x
x
x
x
TABLE OF CONTENTS
5
Removing rear wheel
..................................................
Installing the rear wheel
.............................................
Checking the rear hub rubber dampers
........................
Checking the tire condition..............................................
Checking the tire air pressure ..........................................
Checking the spoke tension .............................................
ELECTRICAL SYSTEM ........................................................
Removing the battery
.................................................
Installing the battery
..................................................
Recharging the battery
...............................................
Changing the main fuse ..................................................
Changing fuses of individual power consumers ..................
Removing the headlight mask with the headlight ...............
Installing the headlight mask with the headlight ................
Changing the headlight bulb............................................
Changing the parking light bulb .......................................
Changing the turn signal bulb ..........................................
Checking the headlight setting.........................................
Adjusting the headlight range ..........................................
COOLING SYSTEM .............................................................
Cooling system ...............................................................
Checking the antifreeze and coolant level .........................
Checking the coolant level...............................................
Draining the coolant
..................................................
Filling the cooling system
...........................................
TUNING THE ENGINE ........................................................
Checking the play in the throttle cable..............................
Adjusting the play in the throttle cable
........................
Adjusting the engine characteristic...................................
x
x
x
x
x
x
x
x
x
108
109
110
112
113
114
116
116
117
118
121
122
124
126
127
128
130
131
131
133
133
133
135
137
138
141
141
142
142
Checking the basic position of the shift lever.....................
Adjusting the basic position of the shift lever
...............
SERVICE WORK ON THE ENGINE .......................................
Checking the engine oil level ...........................................
Changing the engine oil and filter, cleaning the oil
screens
.....................................................................
Draining the engine oil
...............................................
Removing the oil filter
................................................
Cleaning the oil screens
.............................................
Installing the oil filter
................................................
Filling up with engine oil
............................................
Adding engine oil ...........................................................
CLEANING, CARE ..............................................................
Cleaning the motorcycle ..................................................
Checks and maintenance steps for winter operation ...........
STORAGE ..........................................................................
Storage..........................................................................
Preparing for use after storage .........................................
TROUBLESHOOTING..........................................................
BLINK CODE .....................................................................
TECHNICAL DATA - ENGINE ...............................................
Capacity - engine oil .......................................................
Capacity - coolant...........................................................
TECHNICAL DATA - ENGINE TIGHTENING TORQUES...........
TECHNICAL DATA - CHASSIS .............................................
Lighting equipment ........................................................
Tires .............................................................................
Capacity - fuel................................................................
TECHNICAL DATA - FORK...................................................
x
x
x
x
x
x
x
144
144
146
146
147
147
148
150
152
152
153
155
155
157
158
158
159
160
163
167
168
168
169
172
173
174
174
175
TABLE OF CONTENTS
TECHNICAL DATA - SHOCK ABSORBER ..............................
TECHNICAL DATA - CHASSIS TIGHTENING TORQUES .........
SUBSTANCES....................................................................
AUXILIARY SUBSTANCES...................................................
STANDARDS......................................................................
INDEX ...............................................................................
6
176
178
182
186
188
189
MEANS OF REPRESENTATION
Symbols used
The meaning of specific symbols is described below.
Indicates an expected reaction (e.g. of a work step or a function).
Indicates an unexpected reaction (e.g. of a work step or a function).
All work marked with this symbol requires specialist knowledge and technical understanding. In the interest of your
own safety, have these jobs performed by an authorized KTM workshop! There, your motorcycle will be serviced optimally by specially trained experts using the specialist tools required.
Indicates a page reference (more information is provided on the specified page).
Formats used
The typographical formats used in this document are explained below.
Specific name
Identifies a proprietary name.
Name®
Identifies a protected name.
Brand™
Identifies a brand available on the open market.
7
IMPORTANT INFORMATION
8
Use definition
KTM sport motorcycles are designed and constructed to meet the normal demands of regular road and light offroad operation (dirt roads),
but not for use on race courses.
Info
The motorcycle is authorized for public road traffic in the homologous version only.
Service
A prerequisite for fault-free operation and avoiding premature wear is compliance with the instructions for maintenance, care and tuning of
the engine and suspension provided in the owner's manual. Poor adjustment and tuning of the engine and chassis can lead to damage and
breakage of components.
Using the motorcycle in extreme conditions such as very dirty or wet roads can lead to above-average wear of components such as the
transmission train or the brakes. For this reason, it may be necessary to service or replace worn parts before the limit specified in the
service schedule is reached.
It is imperative that you adhere to the stipulated run-in times and service intervals. If you observe these exactly, you will ensure a much
longer service life for your motorcycle.
Warranty
The work prescribed in the service schedule must be carried out by an authorized KTM workshop only and confirmed in the customer's
service record and in the KTM dealer.net; otherwise, all warranty claims will be void. No warranty claims can be considered for damage
resulting from manipulations and/or alterations to the vehicle.
Fuel, oils, etc.
Use the fuels and operating fluids as specified in the Owner's Manual.
IMPORTANT INFORMATION
9
Spare parts, accessories
For your own safety, only use spare parts and accessory products that have been approved and/or recommended by KTM and have them
installed by an authorized KTM workshop. KTM accepts no liability for other products and any resulting damage.
Some spare parts and accessory products are specified in parentheses in the descriptions. Your KTM dealer will be glad to advise you.
You will find the current KTM PowerParts for your vehicle on the KTM website.
International KTM Website: http://www.ktm.com
Work rules
Special tools are necessary for certain tasks. The tools are not contained in the vehicle but can be ordered under the number in parentheses. Example: valve spring mounter (59029019000)
During assembly, non-reusable parts (e.g. self-locking screws and nuts, seals and seal rings, O-rings, pins, lock washers) must be replaced
by new parts.
If a thread lock (e.g. Loctite®) is used for screw connections, be sure to comply with the manufacturer's specific instructions on its usage.
Parts that you want to reuse following repairs and servicing should be cleaned and checked for damage and wear. Change damaged or
worn parts.
Ensure that the vehicle is roadworthy after completing repair and maintenance work.
Transport
Note
Danger of damage The parked vehicle may roll away or fall over.
–
Always place the vehicle on a firm and even surface.
Note
Fire hazard Some vehicle components become very hot when the vehicle is operated.
–
Do not park the vehicle near flammable or explosive substances. Do not place objects on the vehicle while it is still warm from being
run. Always let the vehicle cool first.
IMPORTANT INFORMATION
10
–
Switch off the engine and remove the ignition key.
–
Use straps or other suitable devices to secure the motorcycle against accidents or
falling over.
401448-01
Environment
Offroad motorcycling is a wonderful sport and we naturally hope that you will be able to enjoy it to the fullest. However, it is a potential
problem for the environment and can lead to conflicts with other persons. But if you use your motorcycle responsibly, you can ensure that
such problems and conflicts do not have to occur. To protect the future of motorcycle sport, make sure that you use your motorcycle
legally, display environmental consciousness, and respect the rights of others.
Notes/warnings
Pay close attention to the notes/warnings.
Info
Various information and warning labels are affixed to the vehicle. Do not remove information/warning labels. If they are missing,
you or others may not recognize potential hazards and may therefore be injured.
IMPORTANT INFORMATION
11
Grades of risks
Danger
Identifies a danger that will immediately and invariably lead to fatal or serious permanent injury if the appropriate measures are not
taken.
Warning
Identifies a danger that is likely to lead to fatal or serious injury if the appropriate measures are not taken.
Caution
Identifies a danger that may lead to minor injuries if the appropriate measures are not taken.
Note
Identifies a danger that will lead to considerable machine and material damage if the appropriate measures are not taken.
Warning
Identifies a danger that will lead to environmental damage if the appropriate measures are not taken.
Owner's manual
–
It is important that you read this owner's manual carefully and completely before making your first trip. It contains useful information
and tips to help you operate and handle your motorcycle. Only then will you find out how to customize the motorcycle ideally for your
own use and how you can protect yourself from injury. The owner's manual also contains important information on servicing the motorcycle.
–
The owner's manual is an important component of the motorcycle and should be handed over to the new owner if the vehicle is sold.
VIEW OF VEHICLE
12
View of vehicle, front left (example)
3.1
601762-10
VIEW OF VEHICLE
13
1
Hand brake lever (
p. 19)
2
Clutch lever (
3
Handrails (
4
Filler cap
5
Engine number (
6
Shift lever (
p. 34)
p. 35)
p. 19)
p. 33)
p. 17)
7
Side stand (
8
Seat release (
8
Compression damping of the shock absorber (
p. 32)
p. 56)
VIEW OF VEHICLE
14
View of vehicle, rear right (example)
3.2
601763-10
VIEW OF VEHICLE
15
1
Light switch (
p. 20)
1
Turn signal switch (
1
Horn button (
2
Ignition/steering lock (
3
Combination instrument (
4
Emergency OFF switch (
4
Electric starter button (
5
Throttle grip (
6
Shock absorber, rebound adjustment
7
Foot brake lever (
8
Level viewer, engine oil
9
Type label (
10
Chassis number (
p. 21)
p. 21)
p. 23)
p. 23)
p. 22)
p. 22)
p. 20)
p. 35)
p. 16)
p. 16)
SERIAL NUMBERS
16
Chassis number
4.1
The chassis number 1 is stamped on the steering head on the right.
601764-10
Type label
4.2
The type label 1 is located on the right side of the frame.
601765-10
SERIAL NUMBERS
17
Engine number
4.3
The engine number 1 is stamped on the left side of the engine under the engine sprocket.
100211-10
Key number
4.4
The key number 1 can be found on the KEYCODECARD.
Info
You need the key number to order a spare key. Keep the KEYCODECARD in a safe
place.
100179-10
SERIAL NUMBERS
18
Fork part number
4.5
The fork part number 1 is stamped on the inner side of the fork stub.
601780-10
Shock absorber part number
4.6
The shock absorber part number 1 is on the left of the shock absorber.
101048-10
CONTROLS
19
Clutch lever
5.1
The clutch lever 1 is fitted on the left side of the handlebar.
The clutch is hydraulically operated and self-adjusting.
601766-10
Hand brake lever
5.2
The hand break lever 1 is fitted on the right side of the handlebar.
The hand brake lever operates the front brake.
601767-10
CONTROLS
20
Throttle grip
5.3
The throttle grip 1 is fitted on the right side of the handlebar.
601767-11
Light switch
5.4
The light switch 1 is fitted on the left side of the handlebar.
Possible states
Low beam on – Light switch is turned downwards. In this position, the low
beam and tail light are switched on.
High beam on – Light switch is turned upwards. In this position, the high
beam and the tail light are switched on.
601768-10
CONTROLS
21
Turn signal switch
5.5
The turn signal switch 1 is fitted on the left side of the handlebar.
Possible states
Turn signal off
Turn signal light, left, on – Turn signal switch pressed to the left. The turn
signal switch returns automatically to the central position after use.
Turn signal light, right, on – Turn signal switch pressed to the right. The
turn signal switch returns automatically to the central position after use.
601768-11
To switch off the turn signal light, press the turn signal switch towards the switch case.
Horn button
5.6
The horn button 1 is fitted on the left side of the handlebar.
Possible states
• Horn button
• Horn button
601768-12
in neutral position
pressed – The horn is operated in this position.
CONTROLS
22
Emergency OFF switch
5.7
The emergency OFF switch 1 is fitted on the right side of the handlebar.
Possible states
Emergency OFF switch off – In this position, the ignition circuit is interrupted, a running engine stops, and the engine cannot be started.
Emergency OFF switch on – This position is necessary for operation as the
ignition circuit is closed.
601769-10
Electric starter button
5.8
The electric starter button 1 is fitted on the right side of the handlebar.
Possible states
• Electric starter button
• Electric starter button
601769-11
in basic position
pressed – In this position, the electric starter is actuated.
CONTROLS
23
Ignition/steering lock
5.9
The ignition/steering lock 1 is located in front of the seat.
Possible states
Ignition OFF – In this position, the ignition circuit is interrupted, a running
engine stops, and a non-running engine will not start. The ignition key can
be removed.
Ignition ON – In this position, the ignition circuit is closed and the engine
can be started.
600825-01
Steering locked – In this position, the ignition circuit is interrupted and the
steering locked. The ignition key can be removed.
Combination instrument
5.10
The combination instrument is installed in front of the handlebar.
The combination instrument is divided into 4 function areas.
1 Function buttons
2 Tachometer
3 Indicator lights
4 Display
400832-10
CONTROLS
24
Combination instrument - function buttons
5.11
You can change the display mode with the MODE button 1.
Possible display modes are distance traveled (ODO), trip master 1 (TRIP 1) and trip master 2 (TRIP 2).
Press the SET button 2 to reset the trip master 1 function (TRIP 1) and trip master 2 function (TRIP 2) to 0.0.
Button 3 has no function.
400833-10
Combination instrument - indicator lamps
5.12
The indicator lamps offer additional information about the operating state of the motorcycle.
Possible states
The turn signal indicator light flashes green simultaneously with the turn
signals – Turn signal light is switched on.
The idling speed indicator lamp lights up green – The transmission is
switched to idle.
401440-01
High beam indicator lamp lights up blue – High beam is switched on.
Temperature warning lamp lights up red – Coolant temperature has reached
a critical value.
Low fuel warning lamp lights up orange – Fuel level has reached the
reserve mark. Display switched to TRIP F.
CONTROLS
25
The oil pressure warning lamp lights up red – The oil pressure is too low.
FI warning lamp (MIL) lights up/flashes orange – The OBD (onboard diagnosis) has identified an emissions- or safety-critical fault.
The battery warning lamp lights up red – The voltage in the vehicle system
is too low.
Combination instrument - display
5.13
When you switch on the ignition, all display segments light up for one second as a function
test.
400836-01
LEnGth
Following the display function test, the wheel circumference LEnGth is shown for one second.
Info
2205 mm equals the circumference of the 21" front wheel with a series production
tire.
The display then changes to the last selected mode.
400837-01
CONTROLS
26
Combination instrument - speedometer
5.14
The speed 1 is shown in kilometers per hour km/h or in miles per hour mph.
400838-10
Setting kilometers or miles
5.15
Info
If you change the unit, the value is retained and converted accordingly.
Making the setting according to the country.
Condition
The motorcycle is stationary.
CONTROLS
27
–
Switch on the ignition by turning the ignition key to position ON
–
Press the MODE button repeatedly until the ODO mode is active.
–
Keep the MODE button pressed until the display mode changes from km/h to mph or
from mph to km/h.
.
Guideline
Activation duration of MODE button
10 s
400839-01
Combination instrument - time
5.16
The time is shown in area 1 of the display.
Info
After reconnecting the battery or changing the fuse, the time must be reset.
400838-11
Setting the clock
5.17
Condition
The motorcycle is stationary.
CONTROLS
28
–
Switch on the ignition by turning the ignition key to position ON
–
Press the MODE button repeatedly until the ODO mode is active.
–
Keep the MODE button and the SET button pressed simultaneously.
–
Press the MODE button to set the hour.
.
The time display begins to flash.
400838-01
–
Press the SET button to set the minute.
–
Keep the MODE button and the SET button pressed simultaneously.
The time is set.
Combination instrument - display ODO
5.18
In the ODO display mode, the total distance traveled is shown in kilometers or miles.
Info
This value is retained, even if the battery is disconnected and/or the fuse blows.
400839-01
Combination instrument - setting/resetting TRIP 1
5.19
Info
The TRIP 1 trip counter runs constantly and counts up to 999.9.
The trip counter can be used to measure the distance covered during trips or between two refueling stops. After the value 999.9 is
reached, the trip counter starts at 0.0 again.
CONTROLS
29
–
Switch on the ignition by turning the ignition key to position ON
–
Press the MODE button repeatedly until the TRIP 1 mode is active.
–
Keep the SET button pressed.
.
The TRIP 1 display is set to 0.0.
400840-01
Combination instrument - setting/resetting TRIP 2
5.20
Info
The TRIP 2 trip counter runs constantly and counts up to 999.9.
The trip counter can be used to measure the distance covered during trips or between two refueling stops. After the value 999.9 is
reached, the trip counter starts at 0.0 again.
–
Switch on the ignition by turning the ignition key to position ON
–
Press the MODE button repeatedly until the TRIP 2 mode is active.
–
Keep the SET button pressed.
The TRIP 2 display is set to 0.0.
400841-01
.
CONTROLS
30
Combination instrument - TRIP F display
5.21
If the fuel level drops to the reserve mark, the display automatically changes to TRIP F and
starts to count from 0.0, regardless of the previous display mode.
Info
The low fuel warning lamp lights up in parallel to the TRIP F display.
400842-01
Combination instrument - coolant temperature indicator
5.22
The temperature display consists of 12 bars. The more bars that light up, the hotter the
coolant. When the upper bar lights up, all bars in the display begin to flash and the temperature warning lamp lights up.
Possible states
• Engine cold – Up to four bars light up.
• Engine warm – Five to eleven bars light up.
• Engine hot – All twelve bars flash.
700124-01
CONTROLS
31
Opening the filler cap
5.23
Danger
Fire hazard Fuel is highly flammable.
–
Never refuel the vehicle near open flames or burning cigarettes, and always switch off the engine first. Be careful that no fuel is
spilt, especially on hot vehicle components. Clean up spilt fuel immediately.
–
Fuel in the fuel tank expands when warm and can escape if the tank is overfilled. See the notes on refueling.
Warning
Danger of poisoning Fuel is poisonous and a health hazard.
–
Avoid contact between fuel and skin, eyes and clothing. Do not inhale fuel vapors. If fuel gets into your eyes, rinse immediately
with water and contact a doctor. Wash affected skin areas immediately with soap and water. If fuel is swallowed, contact a doctor immediately. Change clothing that has come into contact with fuel. Store fuel in a suitable canister according to regulations
and keep it out of the reach of children.
Warning
Environmental hazard Improper handling of fuel is a danger to the environment.
–
Do not allow fuel to get into the ground water, the ground, or the sewage system.
–
Lift the cover of filler cap 1 and insert the ignition key.
–
Turn the ignition key 90° counterclockwise and remove the filler cap.
Info
The filler cap has a tank air vent system.
601770-10
CONTROLS
32
Closing filler cap
5.24
–
Put the filler cap back on and turn the ignition key 90° clockwise.
–
Remove the ignition key and fold down the cover.
601771-01
Seat release
5.25
The seat can be released using strap 1.
601772-10
CONTROLS
33
Handrails
5.26
The handrails 1 are used for moving the motorcycle around.
When you have a passenger, the passenger can hold on the handrails during the journey.
601773-10
Passenger footrests
5.27
The passenger footrests can be folded up and down.
Possible states
• Passenger footrests folded up – For operation without a passenger.
• Passenger footrests folded down – For operation with a passenger.
601774-01
CONTROLS
34
Shift lever
5.28
The shift lever 1 is mounted on the left side of the engine.
100215-10
The gear positions can be seen in the photograph.
The neutral or idle position is between the first and second gears.
100212-10
CONTROLS
35
Foot brake lever
5.29
Foot brake lever 1 is located in front of the right footrest.
The rear brake is engaged with the foot brake lever.
100232-10
Side stand
5.30
The side stand 1 is located on the left side of the vehicle.
The side stand is used for parking the motorcycle.
Info
The side stand must be folded up during motorcycle use.
The side stand is coupled with the safety electric starter system - see the riding
instructions.
601803-10
Possible states
• Side stand folded out – The vehicle can be supported on the side stand. The safety
electric starter system is active.
• Side stand folded in – This position is mandatory when riding the motorcycle. The
safety electric starter system is inactive.
PREPARING FOR USE
36
Advice on first use
6.1
Danger
Danger of accidents Danger arising from the rider's judgement being impaired.
–
Do not operate the vehicle while under the influence of alcohol, drugs and certain medications or physically or mentally
impaired.
Warning
Risk of injury Missing or poor protective clothing present an increased safety risk.
–
Wear protective clothing (helmet, boots, gloves, pants and jacket with protectors) every time you ride the vehicle. Always wear
protective clothing, which must be undamaged and meet legal requirements.
Warning
Danger of crashing Poor vehicle handling due to different tire tread patterns on front and rear wheels.
–
The front and rear wheels must be fitted with tires with similar tread patterns to prevent loss of control over the vehicle.
Warning
Danger of accidents Uncontrollable handling characteristic due to non-approved and/or non-recommended tires/wheels.
–
Only tires/wheels approved by KTM and with the corresponding speed index should be used.
Warning
Danger of accidents Reduced road grip with new tires.
–
New tires have a smooth rolling surface and therefore cannot provide full road grip. The entire rolling surface must be roughened in the first 200 kilometers (124.3 miles) by moderate riding at alternating angles. The full grip levels are not achieved
until the tires have been run in.
PREPARING FOR USE
37
Warning
Danger of accidents Failure of brake system.
–
If the foot brake lever is not released, the brake linings drag continuously. The rear brake may fail due to overheating. Take your
foot off the foot brake lever when you are not braking.
Info
When using your vehicle, remember that others may feel disturbed by excessive noise.
–
Make sure that the pre-delivery inspection work has been carried out by an authorized KTM workshop.
You receive a delivery certificate and the service record at vehicle handover.
–
Before your first trip, read the entire operating instructions carefully.
–
Get to know the controls.
–
Adjust the basic position of clutch lever. (
–
Adjust the free travel of the hand brake lever. (
p. 85)
p. 88)
–
Adjust the basic position of the foot brake lever.
–
Get used to handling the motorcycle on a suitable piece of land before making a longer trip. Try also to ride as slowly as possible and
in a standing position to get a better feeling for the vehicle.
–
Do not make any offroad trips that over-stress your ability and experience.
–
Hold the handlebar firmly with both hands and keep your feet on the footrests when riding.
–
Run the engine in. (
x(
p. 97)
p. 37)
Running in the engine
6.2
–
During the running-in phase, do not exceed the specified engine speed.
PREPARING FOR USE
38
Guideline
Maximum engine speed
–
During the first: 1,000 km (621.4 mi)
6,000 rpm
After the first: 1,000 km (621.4 mi)
7,800 rpm
Avoid fully opening the throttle!
Loading the vehicle
6.3
Warning
Danger of accidents Unstable handling characteristics.
–
Do not exceed the maximum permitted weight and axle loads. The overall weight consists of: motorcycle operational and with a
full tank, driver and passenger with protective clothing and helmet, baggage.
Warning
Danger of accidents Unstable handling characteristics due to incorrect mounting of suitcase and/or tank rucksack.
–
Mount and secure suitcase and tank rucksack according to the manufacturer's instructions.
Warning
Danger of accidents Unstable handling characteristics at high speed.
–
Adapt your speed according to your payload. Ride more slowly if your motorcycle is loaded with cases or other baggage.
Maximum speed with baggage
130 km/h (80.8 mph)
Warning
Danger of accidents Risk of breakage of suitcase system.
–
If you have fitted suitcases on your motorcycle, read the manufacturer's specifications concerning the maximum payload.
PREPARING FOR USE
39
Warning
Danger of accidents Poor visibility for other road users due to slipped baggage.
–
If the tail light is covered, you are less visible to traffic behind you, especially in the dark. Check that your baggage is fixed
properly at regular intervals.
Warning
Danger of accidents Changed handling characteristics and longer stopping distance with excessive payload.
–
Adapt your speed according to your payload.
Warning
Danger of accidents Unstable handling characteristics due to slipped baggage.
–
Check the way your baggage is fixed regularly.
Warning
Danger of burns A hot exhaust system can burn baggage.
–
Fasten your baggage in such a way that it cannot be burned or singed by the hot exhaust system.
–
If you carry any baggage, make sure it is fixed firmly as close as possible to the center of the vehicle and ensure even weight distribution between the front and rear wheels.
–
Do not exceed the overall maximum permitted weight and the axle loads.
Guideline
Maximum permissible overall weight
350 kg (772 lb.)
Maximum permissible front axle load
150 kg (331 lb.)
Maximum permissible rear axle load
200 kg (441 lb.)
RIDING INSTRUCTIONS
Performing checks and vehicle care when preparing for use
7.1
Info
Before each use, check the state and roadworthiness of the vehicle.
Make sure that the vehicle is in perfect technical condition before use.
–
Check the engine oil level. (
–
Check the front brake fluid level. (
–
Check the rear brake fluid level. (
–
Check the front brake linings. (
p. 92)
–
Check the rear brake linings. (
p. 101)
–
Check the brake system function.
–
Check the coolant level. (
p. 135)
–
Check the chain for dirt. (
p. 75)
–
Check the chain tension. (
p. 76)
–
Check the tire condition. (
p. 112)
–
Check the tire air pressure. (
–
Check the settings of all controls and ensure that they can be operated smoothly.
–
Check that the electrical equipment is functioning correctly.
–
Check that baggage is correctly secured.
–
Sit on the motorcycle and check the rear mirror setting.
–
Check the fuel level.
p. 146)
p. 90)
p. 98)
p. 113)
40
RIDING INSTRUCTIONS
41
Starting
7.2
Danger
Danger of poisoning Exhaust gases are poisonous and inhaling them may result in unconsciousness and/or death.
–
When running the engine, always make sure there is sufficient ventilation, and do not start or run the engine in an enclosed
space without an effective exhaust extraction system.
Caution
Danger of accidents If the vehicle is operated with a discharged battery or without a battery, electronic components and safety
equipment may be damaged.
–
Never operate the vehicle with a discharged battery or without a battery.
Note
Engine failure High engine speeds in cold engines have a negative effect on the service life of the engine.
–
Always warm up the engine at low engine speeds.
–
Turn the emergency OFF switch to the position
–
Switch on the ignition by turning the ignition key to position ON
.
.
After you switch on the ignition, you can hear the fuel pump working for about 2
seconds. At the same time, the function test of the combination instrument is run.
–
Shift gear to neutral.
The green idling speed indicator lamp N lights up.
–
B00103-10
Press the electric starter button
.
RIDING INSTRUCTIONS
42
Info
Do not press the electric starter button until the function test of the combination
instrument is finished.
When starting, DO NOT open the throttle. If you open the throttle during the starting procedure, fuel is not injected by the engine management system and the
engine cannot start.
Press the starter for a maximum of 5 seconds. Wait for at least 5 seconds before
trying again.
This motorcycle is equipped with a safety start system. You can only start the
engine if the gearbox is in neutral or if the clutch is pulled when a gear is
engaged. If the side stand is folded out and you shift into gear and release the
clutch, the engine stops.
–
Take the weight off the side stand and swing it back up with your foot as far as it will
go.
Starting off
7.3
–
Pull the clutch lever, engage 1st gear, release the clutch lever slowly and simultaneously open the throttle carefully.
Shifting, riding
7.4
Warning
Danger of accidents Abrupt load alterations can cause the vehicle to get out of control.
–
Avoid abrupt load alterations and sudden braking actions, and adapt your speed to the road conditions.
Warning
Danger of accidents If you change down at high engine speed, the rear wheel can lock up.
–
Do not change into a low gear at high engine speed. The engine races and the rear wheel can lock up.
RIDING INSTRUCTIONS
43
Warning
Danger of accidents Malfunctions caused by incorrect ignition key position.
–
Do not change the ignition key position during a journey.
Warning
Danger of accidents Distraction from traffic activity by adjustments to the vehicle.
–
Make all adjustments when the vehicle is at a standstill.
Warning
Risk of injury Falling off of the passenger.
–
The passenger must be capable of properly holding onto the driver or the grab handles and of keeping his or her feet on the
passenger footrests. Note the regulations governing the minimum age of passengers in your country.
Warning
Danger of accidents Danger of accidents caused by dangerous driving.
–
Comply with traffic regulations and ride defensively and foresightedly to detect sources of danger early on.
Warning
Danger of accidents Reduced road grip with cold tires.
–
On every journey, take the first miles carefully at moderate speed until the tires reach operating temperature and optimal road
grip is ensured.
Warning
Danger of accidents Reduced road grip with new tires.
–
New tires have a smooth rolling surface and therefore cannot provide full road grip. The entire rolling surface must be roughened in the first 200 kilometers (124.3 miles) by moderate riding at alternating angles. The full grip levels are not achieved
until the tires have been run in.
RIDING INSTRUCTIONS
44
Warning
Danger of accidents Unstable handling characteristics.
–
Do not exceed the maximum permitted weight and axle loads. The overall weight consists of: motorcycle operational and with a
full tank, driver and passenger with protective clothing and helmet, baggage.
Warning
Danger of accidents Unstable handling characteristics due to slipped baggage.
–
Check the way your baggage is fixed regularly.
Warning
Danger of accidents Lack of roadworthiness.
–
After a fall, check the vehicle as usual before preparing for use.
Note
Engine failure Unfiltered intake air has a negative effect on the service life of the engine.
–
Never ride the vehicle without an air filter since dust and dirt can get into the engine and result in increased wear.
Note
Engine failure Overheating of engine.
–
If the coolant temperature warning lamp lights up, stop and switch off the engine. Allow the engine to cool down and check the
coolant level in the radiator, and top up if necessary. If you continue with the coolant temperature warning lamp alight, you may have
engine failure.
Info
If unusual noises arise during operation, stop immediately, park the vehicle properly and contact an authorized KTM workshop.
RIDING INSTRUCTIONS
45
–
When conditions allow (incline, road situation, etc.), you can shift into a higher gear.
–
Release the throttle while simultaneously pulling the clutch lever, shift into the next
gear, release the clutch and open the throttle.
Info
You can see the positions of the 6 forward gears in the figure. The neutral or idle
position is between the first and second gears. First gear is used for starting off
or for steep inclines.
The operating temperature is reached when 5 bars of the temperature indicator
light up.
100212-10
–
After reaching maximum speed by fully opening the throttle grip, turn the throttle back
so it is ¾ open. This will barely reduce the speed but fuel consumption will be considerably lower.
–
Accelerate only up to a speed suitable for the road surface and weather conditions.
When traveling in bends, do not shift, and accelerate very carefully.
–
To shift down, brake if necessary and close the throttle at the same time.
–
Pull the clutch lever and shift into a lower gear, release the clutch lever slowly and open
the throttle or shift again.
–
If the engine stalls (e.g. at a crossroads), just pull the clutch lever and press the starter
button. You do not have to shift into neutral.
–
Switch off the engine if you expect to be standing for a long time.
–
Avoid frequent and longer slipping of the clutch. This heats the engine oil, the engine
and the cooling system.
–
Ride with a lower engine speed instead of with a high engine speed and a slipping
clutch.
–
If the FI warning lamp (MIL) lights up during a trip, stop immediately. When you shift to
neutral, the FI warning lamp (MIL) starts to flash.
RIDING INSTRUCTIONS
46
Info
From the flashing rhythm, you can derive a two-digit number, the so-called blink
code. The blink code tells you which component has a fault.
Braking
7.5
Warning
Danger of accidents If you brake too hard, the wheels can lock.
–
Adapt your braking to the traffic situation and the road conditions.
Warning
Danger of accidents Reduced braking efficiency due to wet or dirty brakes.
–
Clean or dry dirty or wet brakes by riding and braking gently.
Warning
Danger of accidents Reduced braking efficiency caused by spongy pressure point of front or rear brake.
–
Check the brake system and do not continue riding. (Your authorized KTM workshop will be glad to help.)
Warning
Danger of accidents Failure of brake system.
–
If the foot brake lever is not released, the brake linings drag continuously. The rear brake may fail due to overheating. Take your
foot off the foot brake lever when you are not braking.
Warning
Danger of accidents Longer stopping distance due to higher overall weight.
–
Take the longer stopping distance into account when carrying a passenger and baggage.
RIDING INSTRUCTIONS
47
Warning
Danger of accidents Delayed brake action on salted roads.
–
There may be salt deposits on the brake discs. In order to restore the normal braking efficiency, you will need to remove the
deposits from the discs by carefully applying the brakes.
–
To brake, release the throttle and operate the front and rear brakes simultaneously.
–
On sandy, wet or slippery surfaces, use the rear brake.
–
Braking should always be completed before you go into a bend. Change down to a lower gear appropriate to your road speed.
–
On long downhill stretches, use the braking effect of the engine. Change down one or two gears, but do not overstress the engine. In
this way, you have to brake far less and the brakes do not overheat.
Stopping, parking
7.6
Warning
Risk of misappropriation Usage by unauthorized persons.
–
Never leave the vehicle while the engine is running. Secure the vehicle against use by unauthorized persons. If you leave the
vehicle, lock the steering and remove the ignition key.
Warning
Danger of burns Some vehicle components become very hot when the vehicle is operated.
–
Do not touch hot components such as exhaust system, radiator, engine, shock absorber and brakes. Allow these components to
cool down before starting work on them.
Note
Danger of damage The parked vehicle may roll away or fall over.
–
Always place the vehicle on a firm and even surface.
Note
Fire hazard Some vehicle components become very hot when the vehicle is operated.
RIDING INSTRUCTIONS
–
48
Do not park the vehicle near flammable or explosive substances. Do not place objects on the vehicle while it is still warm from being
run. Always let the vehicle cool first.
Note
Material damage Damage and destruction of components by excessive load.
–
The side stand is designed for the weight of the motorcycle only. Do not sit on the motorcycle when it is supported by the side stand
only. The side stand and/or the frame could be damaged and the motorcycle could fall over.
–
Brake the motorcycle.
–
Shift gear to neutral.
–
Switch off the ignition by turning the ignition key to position OFF
.
Info
If the engine is switched off with the emergency OFF switch and the ignition remains switched on at the ignition lock, power
continues to flow to most power consumers and the battery will discharge. You should therefore always switch off the engine
with the ignition key - the emergency OFF switch is intended for emergencies only.
–
Park the motorcycle on a firm surface.
–
Swing the side stand forward with your foot as far as it will go and lean the vehicle on it.
–
Lock the steering by turning the handlebar fully to the left, pressing down the ignition key to position and turning it to position
To make the steering lock engage more easily, move the handlebar a little to the left and right. Remove the ignition key.
.
Refueling
7.7
Danger
Fire hazard Fuel is highly flammable.
–
Never refuel the vehicle near open flames or burning cigarettes, and always switch off the engine first. Be careful that no fuel is
spilt, especially on hot vehicle components. Clean up spilt fuel immediately.
–
Fuel in the fuel tank expands when warm and can escape if the tank is overfilled. See the notes on refueling.
RIDING INSTRUCTIONS
49
Warning
Danger of poisoning Fuel is poisonous and a health hazard.
–
Avoid contact of the fuel with skin, eyes and clothing. Do not inhale fuel vapors. If fuel gets into your eyes, rinse immediately
with water and contact a doctor. Wash affected skin areas immediately with soap and water. If fuel is swallowed, contact a doctor immediately. Change clothing that has come into contact with fuel.
Note
Material damage Premature clogging of the fuel filter.
–
In some countries and regions, the available fuel quality and cleanliness may not be sufficient. This will result in problems with the
fuel system. (Your authorized KTM workshop will be glad to help.)
–
Only refuel with clean fuel that meets the specified standards.
Warning
Environmental hazard Improper handling of fuel is a danger to the environment.
–
Do not allow fuel to get into the ground water, the ground, or the sewage system.
–
Switch off the engine.
–
Open the filler cap. (
–
Fill the fuel tank with fuel up to measurement A.
p. 31)
Guideline
Measurement A
Total fuel tank
capacity, approx.
400405-10
–
Close the filler cap. (
20 mm (0.79 in)
12 l (3.2 US gal)
p. 32)
Super unleaded (ROZ 95/RON 95/PON
91) ( p. 185)
RIDING INSTRUCTIONS
50
–
Press the SET button 2 for two seconds.
The fuel level warning lamp 1 switches off. TRIP F is set to 0.0 and the display
returns to the previous display mode.
Info
If you do not press the SET button 2, the reset takes place automatically after
about three minutes.
B00104-10
SERVICE SCHEDULE
51
Service schedule
8.1
K10N
K100A
K200A
Check that the electrical equipment is functioning correctly.
•
•
•
Read out the fault memory using the KTM diagnostics tool.
•
•
•
•
•
•
•
•
x
Check the measured service values with the KTM diagnostics tool.
Change the engine oil and filter, clean the oil screens.
x(
x
p. 147)
Check the front brake linings. (
p. 92)
•
•
•
Check the rear brake linings. (
p. 101)
•
•
•
•
•
•
Check the brake lines for damage and leakage.
•
•
•
Check the rear brake fluid level. (
•
•
•
•
•
•
•
•
•
•
•
Check the brake discs. (
p. 89)
p. 98)
Check the free travel of the foot brake lever. (
p. 97)
Check that the shock absorber and fork are leak tight. If necessary and depending on use, service the fork
and shock absorber.
Check the swingarm bearing.
x
Check the wheel bearing for play.
Check the tire condition. (
Check the tire air pressure. (
Check the spoke tension. (
Check for rim run-out.
p. 113)
p. 114)
x
Check the chain, rear sprocket, engine sprocket and chain guide. (
Check the chain tension. (
•
•
•
•
•
•
•
•
x
p. 112)
p. 76)
p. 67)
•
•
•
•
•
•
p. 79)
Grease all moving parts (e.g. side stand, hand lever, chain, ...) and check for smooth operation.
Clean the dust boots of the fork legs. (
•
•
x
•
•
•
•
•
•
•
•
SERVICE SCHEDULE
Check the front brake fluid level. (
Bleed the fork legs. (
52
p. 90)
K10N
K100A
K200A
•
•
•
•
•
•
•
•
p. 67)
Check the steering head bearing play. (
p. 69)
Change the spark plug.
•
Check the valve clearance.
•
x
Check all hoses (e.g. fuel, cooling, bleeder, drainage, etc.) and sleeves for cracking, leaks, and incorrect
routing.
•
x
Check the antifreeze and coolant level. (
p. 133)
•
Check the cables for damage and routing without sharp bends.
x
Check that the throttle cables are undamaged, routed without sharp bends and set correctly.
Change the air filter. Clean the air filter box.
Check the fuel pressure.
•
x
x
Check the CO adjustment with the KTM diagnostics tool.
Check/rectify the fluid level of the hydraulic clutch. (
Check the screws and nuts for tightness.
x
p. 85)
•
x
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Change the front brake fluid.
x
Change the rear brake fluid. x
Check the clutch. x
Check the headlight setting. (
•
•
•
p. 131)
Check that the radiator fan is functioning properly.
x
Final check: Check the vehicle for roadworthiness and take a test ride.
Read out the fault memory using the KTM diagnostics tool after a test ride.
Make the service entry in KTM DEALER.NET and in the service record.
x
x
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
SERVICE SCHEDULE
K10N: Once after 1,000 km (621.4 mi)
K100A: Every 10,000 km (6,214 mi) or annually or after every sporting use
K200A: Every 20,000 km (12,428 mi) or every 2 years
53
TUNING THE CHASSIS
54
Fork/shock absorber
9.1
The fork and the shock absorber offer many options of adapting the chassis to your riding
style and the payload.
Info
To help you adapt the vehicle, we have summarized our findings in Table 1. You
can find the table on the underside of the seat.
100242-01
These adjustments should be understood as a guideline and should always be the basis
of your own personal chassis adaptation. Do not change the adjustments at random or by
more than ± 40%, since otherwise the riding characteristics could deteriorate, particularly
at high speeds.
Adjusting the compression damping of the fork
9.2
Info
The hydraulic compression damping determines the fork suspension behavior.
–
Turn adjusting screws 1 clockwise all the way.
Info
The adjusting screws are located at the bottom end of the fork legs.
Make the same adjustment on both fork legs.
–
601775-10
Turn back counterclockwise by the number of clicks corresponding to the fork type.
TUNING THE CHASSIS
55
Guideline
Compression damping
Comfort
20 clicks
Standard
15 clicks
Sport
10 clicks
Full payload
10 clicks
Info
Turn clockwise to increase damping; turn counterclockwise to reduce damping.
Adjusting the rebound damping of the fork
9.3
Info
The hydraulic rebound damping determines the fork rebound behavior.
–
Turn adjusting screws 1 clockwise all the way.
Info
The adjusting screws are located at the top end of the fork legs.
Make the same adjustment on both fork legs.
–
601776-10
Turn back counterclockwise by the number of clicks corresponding to the fork type.
TUNING THE CHASSIS
56
Guideline
Rebound damping
Comfort
20 clicks
Standard
15 clicks
Sport
10 clicks
Full payload
10 clicks
Info
Turn clockwise to increase damping; turn counterclockwise to reduce damping.
Compression damping of the shock absorber
9.4
The compression damping of the shock absorber is divided into two ranges: high-speed and low-speed.
High-speed and low-speed refer to the compression speed of the rear wheel suspension and not to the vehicle speed.
The high-speed setting, for example, has an effect on the landing after a jump: the rear wheel suspension compresses more quickly.
The low-speed setting, for example, has an effect when riding over long ground swells: the rear wheel suspension compresses more slowly.
These two ranges can be adjusted separately, although the transition between high-speed and low-speed is gradual. Thus, changes in the
high-speed range affect the compression damping in the low-speed range and vice versa.
Adjusting the low-speed compression damping of the shock absorber
9.5
Caution
Danger of accidents Disassembly of pressurized parts can lead to injury.
–
The shock absorber is filled with high density nitrogen. Adhere to the description provided. (Your authorized KTM workshop will
be glad to help.)
TUNING THE CHASSIS
57
Info
The low-speed setting takes effect during the slow to normal compression of the shock absorber.
–
Turn adjusting screw 1 clockwise with a screwdriver up to the last perceptible click.
Info
Do not loosen fitting 2!
–
Turn back counterclockwise by the number of clicks corresponding to the shock
absorber type.
Guideline
Compression damping, low-speed
601777-10
Comfort
20 clicks
Standard
15 clicks
Sport
10 clicks
Full payload
10 clicks
Info
Turn clockwise to increase damping; turn counterclockwise to reduce damping.
Adjusting the high-speed compression damping of the shock absorber
9.6
Caution
Danger of accidents Disassembly of pressurized parts can lead to injury.
–
The shock absorber is filled with high density nitrogen. Adhere to the description provided. (Your authorized KTM workshop will
be glad to help.)
TUNING THE CHASSIS
58
Info
The high-speed setting takes effect during the fast compression of the shock absorber.
–
Turn adjusting screw 1 clockwise all the way using a socket wrench.
Info
Do not loosen fitting 2!
–
Turn back counterclockwise by the number of turns corresponding to the shock
absorber type.
Guideline
Compression damping, high-speed
601777-11
Comfort
2 turns
Standard
1.5 turns
Sport
1 turn
Full payload
1 turn
Info
Turn clockwise to increase damping; turn counterclockwise to reduce damping.
Adjusting the rebound damping of the shock absorber
9.7
Caution
Danger of accidents Disassembly of pressurized parts can lead to injury.
–
The shock absorber is filled with high density nitrogen. Adhere to the description provided. (Your authorized KTM workshop will
be glad to help.)
TUNING THE CHASSIS
59
–
Turn adjusting screw 1 clockwise up to the last perceptible click.
–
Turn back counterclockwise by the number of clicks corresponding to the shock
absorber type.
Guideline
Rebound damping
100247-10
Comfort
20 clicks
Standard
15 clicks
Sport
10 clicks
Full payload
10 clicks
Info
Turn clockwise to increase damping; turn counterclockwise to reduce damping.
Measuring the unloaded rear wheel sag
9.8
Preliminary work
– Raise the motorcycle with the lift stand. (
p. 66)
Main work
– Measure the vertical distance between the rear axle and a fixed point such as a marking
on the side cover.
A
0
–
Note down the value as dimension A.
400988-10
Follow-up work
– Remove the motorcycle from the lift stand. (
p. 66)
TUNING THE CHASSIS
60
Checking the static sag of the shock absorber
9.9
A
0
–
Measure distance A of rear wheel unloaded. (
–
Hold the motorcycle upright with the aid of an assistant.
–
Measure the distance between the rear axle and the fixed point again.
–
Note down the value as dimension B.
p. 59)
Info
The static sag is the difference between measurements A and B.
–
Check the static sag.
»
If the static sag is less or more than the specified value:
–
B
0
400989-10
Adjust the spring preload of the shock absorber.
x(
p. 61)
TUNING THE CHASSIS
61
Checking the riding sag of the shock absorber
9.10
–
Measure distance A of rear wheel unloaded. (
–
With another person holding the motorcycle, the rider, wearing full protective clothing,
sits on the seat in a normal sitting position (feet on footrests) and bounces up and down
a few times.
–
Another person now measures the distance between the rear axle and a fixed point.
–
Note down the value as dimension C.
A
0
p. 59)
The rear wheel suspension levels out.
Info
The riding sag is the difference between measurements A and C.
–
Check the riding sag.
»
C
0
If the riding sag differs from the specified measurement:
–
Adjust the riding sag.
x(
p. 63)
400990-10
Adjusting the spring preload of the shock absorber
9.11
x
Caution
Danger of accidents Disassembly of pressurized parts can lead to injury.
–
The shock absorber is filled with high density nitrogen. Adhere to the description provided. (Your authorized KTM workshop will
be glad to help.)
TUNING THE CHASSIS
62
Info
Before changing the spring preload, make a note of the present setting, e.g., by measuring the length of the spring.
Preliminary work
– Raise the motorcycle with the work stand.
–
Remove the shock absorber.
–
After removing the shock absorber, clean it thoroughly.
x
Main work
– Release retaining ring 1.
–
Turn adjusting ring 2 until the spring is fully relaxed.
Hook wrench (T106S)
–
Measure the overall spring length without a load.
–
Tighten the spring by turning adjusting ring 2 to the specified measurement.
Guideline
Spring preload
201271-11
20 mm (0.79 in)
Info
Depending on the static sag and/or the riding sag, it may be necessary to
increase or decrease the spring preload.
–
Tighten retaining ring 1.
Subsequent work
– Install the shock absorber.
x
–
Mount the side cover.
–
Mount the seat. (
–
Remove the motorcycle from the work stand.
p. 72)
TUNING THE CHASSIS
Adjusting the riding sag
9.12
63
x
Preliminary work
– Raise the motorcycle with the work stand.
–
Remove the shock absorber.
–
After removing the shock absorber, clean it thoroughly.
x
Main work
– Choose and mount a suitable spring.
Guideline
Spring rate
Medium (standard)
80 N/mm (457 lb/in)
Hard
85 N/mm (485 lb/in)
Info
The spring rate is shown on the outside of the spring.
201352-10
Subsequent work
– Install the shock absorber.
x
–
Mount the side cover.
–
Mount the seat. (
–
Remove the motorcycle from the work stand.
–
Check the static sag of the shock absorber. (
–
Adjust the rebound damping of the shock absorber. (
p. 72)
p. 60)
p. 58)
TUNING THE CHASSIS
64
Handlebar position
9.13
On the upper triple clamp, there are 2 holes at a distance A to each other.
Distance A between holes
15 mm (0.59 in)
The holes on the handlebar support are placed at a distance B from the center.
Distance B between holes
3.5 mm (0.138 in)
The handlebar can be mounted in 4 different positions. In this way, the handlebar can be
installed in the position most comfortable for the rider.
401454-11
Adjusting handlebar position
9.14
x
–
Remove the four screws 1. Remove the handlebar clamp. Remove the handlebar and
lay it to one side.
Info
Protect the motorcycle and its attachments from damage by covering them.
Do not bend the cables and lines.
401454-10
–
Remove the two screws 2. Remove the handlebar support.
–
Place the handlebar support in the required position. Fit and tighten the two screws 2.
Guideline
Screw, handlebar support
M10
40 Nm
(29.5 lbf ft)
Info
Position the left and right handlebar supports evenly.
Loctite® 243™
TUNING THE CHASSIS
65
–
Position the handlebar.
Info
Make sure cables and wiring are positioned correctly.
–
Position the handlebar clamp. Fit and evenly tighten the four screws 1.
Guideline
Screw, handlebar clamp
M8
20 Nm
(14.8 lbf ft)
SERVICE WORK ON THE CHASSIS
Raising the motorcycle with the lift stand
10.1
Note
Danger of damage The parked vehicle may roll away or fall over.
–
Always place the vehicle on a firm and even surface.
–
Raise the motorcycle using the underride guard under the motorcycle.
–
Secure the motorcycle against falling over.
The wheels must no longer touch the ground.
601778-01
Removing the motorcycle from the lift stand
10.2
Note
Danger of damage The parked vehicle may roll away or fall over.
–
Always place the vehicle on a firm and even surface.
–
Remove the motorcycle from the lift stand and rest it on its side stand.
–
Remove the lift stand.
66
SERVICE WORK ON THE CHASSIS
67
Bleeding the fork legs
10.3
Preliminary work
– Lean the motorcycle on the side stand.
Main work
– Remove bleeder screws 1 briefly.
Any excess pressure escapes from the interior of the fork.
–
Mount and tighten bleeder screws.
Info
Carry out this action on both fork legs.
601779-10
Cleaning the dust boots of the fork legs
10.4
Preliminary work
– Raise the motorcycle with the lift stand. (
–
Loosen the fork protection. (
p. 66)
p. 68)
Main work
– Push dust boot 1 of both fork legs downwards.
Info
The dust boots should remove dust and coarse dirt particles from the fork tubes.
Over time, dirt can penetrate behind the dust boots. If this dirt is not removed,
the oil seals behind can start to leak.
601804-10
SERVICE WORK ON THE CHASSIS
68
Warning
Danger of accidents Reduced braking efficiency due to oil or grease on the
brake discs.
–
–
Always keep the brake discs free of oil and grease, and clean them with
brake cleaner when necessary.
Clean and oil the dust boots and inner fork tube of both fork legs.
Universal oil spray (
p. 187)
–
Press the dust boots back into their normal position.
–
Remove excess oil.
Follow-up work
– Position the fork protection. (
p. 69)
–
Remove the motorcycle from the lift stand. (
–
Remove screws 1 and take off clamp.
–
Remove screws 2 on left fork leg. Push the fork protection downwards.
–
Remove the screws on the right fork leg. Push the fork protection downwards.
p. 66)
Loosening the fork protection
10.5
601790-10
SERVICE WORK ON THE CHASSIS
69
Positioning the fork protection
10.6
–
Position the fork protection on the left fork leg. Mount and tighten screws 1.
Guideline
Remaining screws, chassis
M6
10 Nm (7.4 lbf ft)
–
Position the brake line and wiring harness. Put the clamp on, mount and tighten
screws 2.
–
Position the fork protection on the right fork leg. Mount and tighten the screws.
Guideline
Remaining screws, chassis
601790-11
M6
10 Nm (7.4 lbf ft)
Checking the steering head bearing play
10.7
Warning
Danger of accidents Unstable vehicle handling from incorrect steering head bearing play.
–
Adjust the steering head bearing play without delay. (Your authorized KTM workshop will be glad to help.)
Info
If the bike is ridden with play in the steering head bearing, the bearing and the bearing seats in the frame can become damaged
over time.
Preliminary work
– Raise the motorcycle with the lift stand. (
p. 66)
SERVICE WORK ON THE CHASSIS
70
Main work
– Move the handlebar to the straight-ahead position. Move the fork legs to and fro in the
direction of travel.
No play should be noticeable in the steering head bearing.
»
If there is noticeable play present:
–
–
Adjust the play of the steering head bearing.
p. 70)
Move the handlebar to and fro over the entire steering range.
The handlebar must be able to move easily over the entire steering range. No resting
locations should be noticeable.
100298-10
»
If click positions are noticeable:
–
Adjust the play of the steering head bearing.
–
Check the steering head bearing and change if necessary.
Subsequent work
– Remove the motorcycle from the lift stand. (
Adjusting the play of the steering head bearing
10.8
x(
p. 66)
x
Preliminary work
– Raise the motorcycle with the lift stand. (
x(
p. 66)
p. 70)
SERVICE WORK ON THE CHASSIS
–
Loosen screw 1. Remove screw 2.
–
Loosen and retighten screw 3.
71
Guideline
Screw, top steering head
M20x1.5
12 Nm (8.9 lbf ft)
–
Using a plastic hammer, tap lightly on the upper triple clamp to avoid strains.
–
Fully tighten screws 1.
Guideline
Screw, top triple clamp
601781-10
–
M8
17 Nm
(12.5 lbf ft)
M8
20 Nm
(14.8 lbf ft)
Mount and tighten screw 2.
Guideline
Screw, steering stem
Subsequent work
– Check the steering head bearing play. (
–
p. 69)
Remove the motorcycle from the lift stand. (
p. 66)
SERVICE WORK ON THE CHASSIS
72
Removing the seat
10.9
–
Pull on strap 1 and raise the rear of the seat at the same time.
–
Pull back the seat and lift it off.
601772-10
Mounting the seat
10.10
601782-10
–
Hook slot 1 of the seat onto screw 2, press the rear downward and at the same time push it forward.
–
Push locking pin 3 into lock housing 4 and push the back of the seat down until the locking pin locks in place with an audible click.
–
Finally, check that the seat is correctly mounted.
SERVICE WORK ON THE CHASSIS
Removing the air filter
10.11
73
x
Preliminary work
– Remove the seat. (
p. 72)
Main work
– Remove screws 1. Remove filter box top 2.
601783-10
Note
Engine failure Unfiltered intake air has a negative effect on the service life of the
engine.
–
–
601784-10
Never ride the vehicle without an air filter since dust and dirt can get into the
engine and result in increased wear.
Remove air filter 3.
SERVICE WORK ON THE CHASSIS
Installing the air filter
10.12
74
x
Main work
– Clean the air filter box.
–
Mount air filter 1.
Info
The air filter must lie flush against the air filter box along the entire sealing surface A.
If the air filter is not correctly mounted, dust and dirt can enter the engine and
cause damage.
601785-10
–
Hook filter box top 2 into the front of the air filter box and swing down.
–
Mount and tighten screws 3.
Guideline
Screw, air filter box top
601783-11
Subsequent work
– Mount the seat. (
p. 72)
M6
2 Nm (1.5 lbf ft)
SERVICE WORK ON THE CHASSIS
75
Checking the chain for dirt
10.13
–
Check the chain for heavy soiling.
»
If the chain is very dirty:
–
Clean the chain. (
p. 75)
400678-01
Cleaning the chain
10.14
Warning
Danger of accidents Oil or grease on the tires reduces their grip.
–
Remove oil and grease with a suitable cleaning material.
Warning
Danger of accidents Reduced braking efficiency due to oil or grease on the brake discs.
–
Always keep the brake discs free of oil and grease, and clean them with brake cleaner when necessary.
Warning
Environmental hazard Hazardous substances cause environmental damage.
–
Oil, grease, filters, fuel, cleaners, brake fluid, etc., should be disposed of as stipulated in applicable regulations.
SERVICE WORK ON THE CHASSIS
76
Info
The service life of the chain depends largely on its maintenance.
–
Clean the chain regularly.
–
Rinse off loose dirt with a soft jet of water.
–
Remove old grease remains with chain cleaner.
Chain cleaner (
–
p. 186)
After drying, apply chain spray.
Off-road chain spray (
p. 187)
400725-01
Checking the chain tension
10.15
Warning
Danger of accidents Danger caused by incorrect chain tension.
–
If the chain tension is too high, the components of the secondary power train (chain, engine sprocket, rear sprocket, bearings
in transmission and rear wheel) are under additional load. Apart from premature wear, in extreme cases the chain can rupture
or the countershaft of the transmission can break. On the other hand, if the chain is loose, it can fall off the engine sprocket or
the rear sprocket and block the rear wheel or damage the engine. Check the chain tension and correct if necessary.
SERVICE WORK ON THE CHASSIS
77
–
Lean the motorcycle on the side stand.
–
Shift gear to neutral.
–
Push the chain upward at a distance B from the chain sliding guard and determine the
chain tension A.
Info
The upper chain section C must be taut.
Chain wear is not always even. Repeat this measurement at different chain positions.
»
Chain tension
5 mm (0.2 in)
Distance to chain sliding guard
30 mm (1.18 in)
If the chain tension does not meet specifications:
–
Adjust the chain tension. (
p. 77)
100249-10
Adjusting the chain tension
10.16
Warning
Danger of accidents Danger caused by incorrect chain tension.
–
If the chain tension is too high, the components of the secondary power train (chain, engine sprocket, rear sprocket, bearings
in transmission and rear wheel) are under additional load. Apart from premature wear, in extreme cases the chain can rupture
or the countershaft of the transmission can break. On the other hand, if the chain is loose, it can fall off the engine sprocket or
the rear sprocket and block the rear wheel or damage the engine. Check the chain tension and correct if necessary.
SERVICE WORK ON THE CHASSIS
Preliminary work
– Check the chain tension. (
78
p. 76)
Main work
– Loosen nut 1.
–
–
Loosen nuts 2.
Adjust the chain tension by turning adjusting screws 3 on the left and right.
Guideline
Chain tension
5 mm (0.2 in)
Turn the left and right adjusting screws 3 so that the markings on the left and right
chain adjusters 4 are in the same position relative to the reference marks C. The
rear wheel is then correctly aligned.
Info
The upper chain section must be taut.
Chain wear is not always even. Repeat this measurement at different chain positions.
–
Tighten nuts 2.
–
Make sure that the chain adjusters 4 are installed correctly on adjusting screws 3.
–
100250-10
Tighten nut 1.
Guideline
Nut, rear wheel spindle
M25x1.5
90 Nm
(66.4 lbf ft)
SERVICE WORK ON THE CHASSIS
79
Check the chain, rear sprocket, engine sprocket and chain guide
10.17
Preliminary work
– Raise the motorcycle with the lift stand. (
p. 66)
Main work
– Shift gear to neutral.
–
Check the rear sprocket and engine sprocket for wear.
»
If the rear sprocket and engine sprocket are worn:
–
Replace the rear sprocket or engine sprocket.
x
Info
100132-10
The engine sprocket, rear sprocket and chain should always be replaced
together.
SERVICE WORK ON THE CHASSIS
–
80
Pull on the upper section of the chain with the specified weight A.
Guideline
Weight of chain wear measurement
0
A
–
15 kg (33 lb.)
Measure distance B of 18 chain links in the lower chain section.
Info
Chain wear is not always even, so you should repeat this measurement at different chain positions.
Maximum distance B at the longest
chain section
»
If the distance B is greater than the specified measurement:
–
B
0
1 2 3
272 mm (10.71 in)
Replace the chain.
x
Info
16 17 18
400987-10
When the chain is replaced, the rear sprocket and engine sprocket
should also be changed.
New chains wear out faster on old, worn sprockets.
SERVICE WORK ON THE CHASSIS
–
Check the chain sliding guard for wear.
»
If the lower edge of the chain pins is in line with or below the chain sliding guard:
–
–
81
Replace the chain sliding guard.
x
Check that the chain sliding guard is firmly seated.
»
If the chain sliding guard is loose:
–
Tighten the chain sliding guard.
Guideline
Screw, chain sliding
guard
401118-01
M6
8 Nm
(5.9 lbf ft)
Loctite® 243™
SERVICE WORK ON THE CHASSIS
–
Check the chain sliding piece for wear.
»
If the lower edge of the chain pins is in line with or below the chain sliding piece:
–
–
82
Change the chain sliding piece.
x
Check that the chain sliding piece is firmly seated.
»
If the chain sliding piece is loose:
–
Tighten the chain sliding piece.
Guideline
Screw, chain sliding piece
M8
401119-01
–
Check the chain guide for wear.
Info
Wear is visible on the front of the chain guide.
»
If the light part of the chain guide is worn:
–
400985-01
Change the chain guide.
x
15 Nm
(11.1 lbf ft)
SERVICE WORK ON THE CHASSIS
–
83
Check that the chain guide is firmly seated.
»
If the chain guide is loose:
–
Tighten the chain guide.
Guideline
Remaining screws, chassis
M6
101068-01
Subsequent work
– Remove the motorcycle from the lift stand. (
p. 66)
10 Nm
(7.4 lbf ft)
SERVICE WORK ON THE CHASSIS
Adjusting chain guide
10.18
84
x
–
Remove screws 1 and 2. Take off the chain guide.
Condition
Number of teeth: ≤ 44 teeth
–
–
Insert nut 3 in hole A. Position the chain guide.
Mount and tighten screws 1 and 2.
Guideline
Screw, chain guide
M6
8 Nm (5.9 lbf ft)
Condition
Number of teeth: ≥ 45 teeth
–
–
Insert nut 3 in hole B. Position the chain guide.
Mount and tighten screws 1 and 2.
Guideline
Screw, chain guide
100299-10
M6
8 Nm (5.9 lbf ft)
SERVICE WORK ON THE CHASSIS
85
Adjusting basic position of clutch lever
10.19
Info
Turn the adjusting screw clockwise to increase the distance between the clutch lever and the handlebar.
Turn the adjusting screw counterclockwise to decrease the distance between the clutch lever and the handlebar.
The range of adjustment is limited.
Turn the adjusting screw by hand only, and do not apply any force.
Do not make any adjustments while riding!
–
Adjust the basic setting of the clutch lever to your hand size by turning adjusting
screw 1.
–
When adjusting the clutch lever, make sure to leave a minimum clearance to other parts
of the vehicle.
Guideline
Minimum clearance
5 mm (0.2 in)
601786-10
Checking/rectifying the fluid level of the hydraulic clutch
10.20
Info
The fluid level rises with increasing wear of the clutch lining disc.
Do not use brake fluid.
–
Move the clutch fluid reservoir mounted on the handlebar to a horizontal position.
SERVICE WORK ON THE CHASSIS
86
–
Remove screws 1.
–
Remove cover 2 with membrane 3.
–
Check the fluid level.
Fluid level under top level of container
»
If the level of the coolant does not meet specifications:
–
Correct the fluid level of the hydraulic clutch.
Hydraulic fluid (15) (
601788-10
–
4 mm (0.16 in)
p. 184)
Position the cover with the membrane. Mount and tighten the screws.
Removing the engine guard
10.21
Preliminary work
– Stand the motorcycle on its side stand on a horizontal surface.
Main work
– Remove screws 1 on the left and right.
–
100198-10
Pull the engine guard forward out of the holders and set it down.
SERVICE WORK ON THE CHASSIS
87
Installing the engine guard
10.22
–
Slide the engine guard into holders 1 at the rear.
–
Position the engine guard. Mount and tighten screws.
Guideline
Remaining screws, chassis
100199-10
M6
10 Nm (7.4 lbf ft)
BRAKES
88
Checking the free travel of the hand brake lever
11.1
Warning
Danger of accidents Brake system failure.
–
If there is no free travel on the hand brake lever, pressure builds up in the front brake circuit. The front brake can fail due to
overheating. Adjust free travel on hand brake lever according to specifications.
–
Push the hand brake to the handlebar and check free travel A.
Free travel of hand brake lever
»
≥ 3 mm (≥ 0.12 in)
If the free travel does not meet specifications:
–
Adjust the free travel of the hand brake lever. (
p. 88)
601805-10
Adjusting the free travel of the hand brake lever
11.2
601805-11
–
Check the free travel of the hand brake lever. (
–
Adjust the free travel of the hand brake lever with adjusting screw 1.
p. 88)
BRAKES
89
Info
Turn the adjusting screw clockwise to reduce free travel. The pressure point
moves away from the handlebar.
Turn the adjusting screw counterclockwise to increase free travel. The pressure
point moves towards the handlebar.
The range of adjustment is limited.
Turn the adjusting screw by hand only, and do not apply any force.
Do not make adjustments while riding.
Checking the brake discs
11.3
Warning
Danger of accidents Reduced braking efficiency due to worn brake disc(s).
–
Change the worn brake disc(s) without delay. (Your authorized KTM workshop will be glad to help.)
–
Check the thickness of the front and rear brake discs in several places to ensure that it
conforms to measurement A.
Info
Wear reduces the thickness of the brake disc at the contact surface 1 of the
brake disc.
Brake discs - wear limit
400406-10
»
Front
4.5 mm (0.177 in)
Rear
3.5 mm (0.138 in)
If the brake disc thickness is less than the specified value:
–
Replace the brake disc.
BRAKES
90
–
Check the front and rear brake discs for damage, cracks, and deformation.
»
If damage, cracks, or deformation are visible on the brake disc:
–
Replace the brake disc.
Checking the front brake fluid level
11.4
Warning
Danger of accidents Failure of the brake system.
–
If the brake fluid level falls below the MIN mark, this indicates a leakage in the brake system or worn-out brake linings. Check
the brake system and do not continue riding. (Your authorized KTM workshop will be glad to help.)
Warning
Danger of accidents Reduced braking efficiency due to old brake fluid.
–
Change the brake fluid of the front and rear brake according to the service schedule. (Your authorized KTM workshop will be
glad to help.)
–
Move the brake fluid reservoir mounted on the handlebar to a horizontal position.
–
Check the brake fluid level in the viewer 1.
»
If the brake fluid level is below the MIN mark:
–
601789-10
Add front brake fluid.
x(
p. 91)
BRAKES
Adding front brake fluid
11.5
91
x
Warning
Danger of accidents Failure of the brake system.
–
If the brake fluid level falls below the MIN mark, this indicates a leakage in the brake system or worn-out brake linings. Check
the brake system and do not continue riding. (Your authorized KTM workshop will be glad to help.)
Warning
Skin irritation Brake fluid can cause skin irritation on contact.
–
Avoid contact with skin and eyes, and keep out of the reach of children.
–
Wear suitable protective clothing and goggles.
–
If brake fluid comes into contact with the eyes, flush the eyes thoroughly with water and consult a physician immediately.
Warning
Danger of accidents Reduced braking efficiency due to old brake fluid.
–
Change the brake fluid of the front and rear brake according to the service schedule. (Your authorized KTM workshop will be
glad to help.)
Warning
Environmental hazard Hazardous substances cause environmental damage.
–
Oil, grease, filters, fuel, cleaners, brake fluid, etc., should be disposed of as stipulated in applicable regulations.
Info
Never use DOT 5 brake fluid! It is silicone-based and purple in color. Oil seals and brake lines are not designed for DOT 5 brake
fluid.
Avoid contact between brake fluid and painted parts. Brake fluid attacks paint!
Use only clean brake fluid from a sealed container.
BRAKES
92
–
Move the brake fluid reservoir mounted on the handlebar to a horizontal position.
–
Remove screws 1.
–
Remove cover 2 with membrane 3.
–
Add brake fluid to level A.
Guideline
Measurement of A
Brake fluid DOT 4 / DOT 5.1 (
601806-10
–
5 mm (0.2 in)
p. 182)
Position the cover with the membrane. Mount and tighten the screws.
Info
Clean up overflowed or spilt brake fluid immediately with water.
Checking the front brake linings
11.6
Warning
Danger of accidents Reduced braking efficiency caused by worn brake linings.
–
Change worn brake linings immediately. (Your authorized KTM workshop will be glad to help.)
Note
Danger of accidents Reduced braking efficiency caused by damaged brake discs.
–
If the brake linings are not changed in time, the steel brake lining carriers grind on the brake disc. The braking effect is greatly
reduced and the brake discs are rendered unserviceable. Check the brake linings regularly.
BRAKES
93
–
Check the brake linings for minimum thickness A.
≥ 1 mm (≥ 0.04 in)
Minimum thickness A
»
If the minimum thickness is less than specified:
–
–
Change the front brake linings.
x(
p. 93)
Check the brake linings for damage and cracking.
»
If there is wear or tearing:
–
Change the front brake linings.
x(
p. 93)
800076-10
Changing the front brake linings
11.7
x
Warning
Danger of accident Brake system failure.
–
Maintenance work and repairs must be carried out professionally. (Your authorized KTM workshop will be glad to help.)
Warning
Skin irritation Brake fluid can cause skin irritation on contact.
–
Avoid contact with skin and eyes, and keep out of the reach of children.
–
Wear suitable protective clothing and goggles.
–
If brake fluid comes into contact with the eyes, flush the eyes thoroughly with water and consult a physician immediately.
Warning
Danger of accidents Reduced braking efficiency due to old brake fluid.
–
Change the brake fluid of the front and rear brake according to the service schedule. (Your authorized KTM workshop will be
glad to help.)
BRAKES
Warning
Danger of accidents Reduced braking efficiency due to oil or grease on the brake discs.
–
Always keep the brake discs free of oil and grease, and clean them with brake cleaner when necessary.
Warning
Danger of accidents Reduced braking efficiency due to use of non-approved brake linings.
–
Brake linings available from accessory suppliers are often not tested and approved for use on KTM vehicles. The construction
and friction factor of the brake linings and therefore the brake power can differ considerably from the original KTM brake linings. If brake linings are used that differ from the originals, there is no guarantee that they comply with the original license.
The vehicle no longer corresponds to the condition at delivery, and the warranty is no longer valid.
Warning
Environmental hazard Hazardous substances cause environmental damage.
–
Oil, grease, filters, fuel, cleaners, brake fluid, etc., should be disposed of as stipulated in applicable regulations.
Info
Never use DOT 5 brake fluid! It is silicone-based and purple in color. Oil seals and brake lines are not designed for DOT 5 brake
fluid.
Avoid contact between brake fluid and painted parts. Brake fluid attacks paint!
Use only clean brake fluid from a sealed container.
94
BRAKES
95
–
Move the brake fluid reservoir mounted on the handlebar to a horizontal position.
–
Remove screws 1.
–
Remove cover 2 with membrane 3.
–
Press the brake caliper onto the brake disc by hand in order to push back the brake pistons. Make sure that no brake fluid escapes from the brake fluid reservoir. If it does,
clean it up.
Info
Make sure when pushing back the brake pistons that you do not press the brake
caliper against the spokes.
601806-11
400418-11
–
Remove cotter pin 4, remove bolt 5 toward the right by striking it and remove the
brake linings.
–
Clean brake caliper and brake caliper support.
BRAKES
96
–
Check that leaf spring 6 in the brake caliper and sliding plate 7 in the brake caliper
support are seated correctly.
–
Insert the brake linings, insert the bolt and mount the cotter pin.
–
Operate the hand brake lever repeatedly until the brake linings are in contact with the
brake disc and there is a pressure point.
400418-10
101057-01
–
Adjust the brake fluid level to level A.
Guideline
Measurement A
Brake fluid DOT 4 / DOT 5.1 (
–
5 mm (0.2 in)
p. 182)
Position the cover with the membrane. Mount and tighten the screws.
Info
601806-12
Clean up overflowed or spilt brake fluid immediately with water.
BRAKES
97
Checking the free travel of foot brake lever
11.8
Warning
Danger of accidents Brake system failure.
–
If there is no free travel on the foot brake lever, pressure builds up on the rear brake circuit. The rear brake can fail due to overheating. Adjust free travel on foot brake lever according to specifications.
–
Move the foot brake lever back and forth between the end stop and the contact to the
foot brake cylinder piston and check free travel A.
Guideline
Free travel at foot brake lever
3… 5 mm (0.12… 0.2 in)
Info
You will know that contact has been made with the foot brake cylinder piston
when there is increased resistance when you activate the foot brake lever.
100256-10
»
If the free travel does not meet specifications:
–
Adjust the basic position of the foot brake lever.
Adjusting the basic position of the foot brake lever
11.9
x(
p. 97)
x
Warning
Danger of accidents Brake system failure.
–
If there is no free travel on the foot brake lever, pressure builds up on the rear brake circuit. The rear brake can fail due to overheating. Adjust free travel on foot brake lever according to specifications.
BRAKES
98
–
Remove screws 3 on foot brake cylinder 4.
–
To adjust the basic position of the foot brake lever individually, loosen nut 1 and turn
screw 2 accordingly.
Info
The range of adjustment is limited. The screw must be screwed into the footrest
bracket by at least four turns.
–
Position foot brake cylinder 4 so that the foot brake lever has the necessary free travel.
Hold screws 3 in place and tighten the nuts.
Guideline
Screw connection, foot brake cylinder
M6
–
Check the free travel of the foot brake lever. (
–
Tighten nut 1.
10 Nm (7.4 lbf ft)
p. 97)
100257-10
Checking rear brake fluid level
11.10
Warning
Danger of accidents Failure of the brake system.
–
If the brake fluid level falls below the MIN mark, this indicates a leakage in the brake system or worn-out brake linings. Check
the brake system and do not continue riding. (Your authorized KTM workshop will be glad to help.)
BRAKES
99
Warning
Danger of accidents Reduced braking efficiency due to old brake fluid.
–
Change the brake fluid of the front and rear brake according to the service schedule. (Your authorized KTM workshop will be
glad to help.)
–
Stand the vehicle upright.
–
Check the brake fluid level in the brake fluid reservoir.
»
If the fluid level reaches the MIN marking 1:
–
Add rear brake fluid.
x(
p. 99)
101058-10
Adding rear brake fluid
11.11
x
Warning
Danger of accidents Failure of the brake system.
–
If the brake fluid level falls below the MIN mark, this indicates a leakage in the brake system or worn-out brake linings. Check
the brake system and do not continue riding. (Your authorized KTM workshop will be glad to help.)
Warning
Skin irritation Brake fluid can cause skin irritation on contact.
–
Avoid contact with skin and eyes, and keep out of the reach of children.
–
Wear suitable protective clothing and goggles.
–
If brake fluid comes into contact with the eyes, flush the eyes thoroughly with water and consult a physician immediately.
BRAKES
100
Warning
Danger of accidents Reduced braking efficiency due to old brake fluid.
–
Change the brake fluid of the front and rear brake according to the service schedule. (Your authorized KTM workshop will be
glad to help.)
Warning
Environmental hazard Hazardous substances cause environmental damage.
–
Oil, grease, filters, fuel, cleaners, brake fluid, etc., should be disposed of as stipulated in applicable regulations.
Info
Never use DOT 5 brake fluid! It is silicone-based and purple in color. Oil seals and brake lines are not designed for DOT 5 brake
fluid.
Avoid contact between brake fluid and painted parts. Brake fluid attacks paint!
Use only clean brake fluid from a sealed container.
–
Stand the vehicle upright.
–
Remove screw cap 1 with the washer and membrane 2.
–
Add brake fluid to the MAX mark.
Brake fluid DOT 4 / DOT 5.1 (
–
p. 182)
Mount the screw cap with the washer and membrane.
Info
101059-10
Clean up overflowed or spilt brake fluid immediately with water.
BRAKES
101
Checking the rear brake linings
11.12
Warning
Danger of accidents Reduced braking efficiency caused by worn brake linings.
–
Change worn brake linings immediately. (Your authorized KTM workshop will be glad to help.)
Note
Danger of accidents Reduced braking efficiency caused by damaged brake discs.
–
If the brake linings are not changed in time, the steel brake lining carriers grind on the brake disc. The braking effect is greatly
reduced and the brake discs are rendered unserviceable. Check the brake linings regularly.
–
Check the brake linings for minimum thickness A.
≥ 1 mm (≥ 0.04 in)
Minimum thickness A
»
If the minimum thickness is less than specified:
–
–
Change the rear brake linings.
x(
p. 101)
Check the brake linings for damage and cracking.
»
If there is wear or tearing:
–
Change the rear brake linings.
x(
p. 101)
100260-10
Changing the rear brake linings
11.13
x
Warning
Danger of accident Brake system failure.
–
Maintenance work and repairs must be carried out professionally. (Your authorized KTM workshop will be glad to help.)
BRAKES
102
Warning
Skin irritation Brake fluid can cause skin irritation on contact.
–
Avoid contact with skin and eyes, and keep out of the reach of children.
–
Wear suitable protective clothing and goggles.
–
If brake fluid comes into contact with the eyes, flush the eyes thoroughly with water and consult a physician immediately.
Warning
Danger of accidents Reduced braking efficiency due to old brake fluid.
–
Change the brake fluid of the front and rear brake according to the service schedule. (Your authorized KTM workshop will be
glad to help.)
Warning
Danger of accidents Reduced braking efficiency due to oil or grease on the brake discs.
–
Always keep the brake discs free of oil and grease, and clean them with brake cleaner when necessary.
Warning
Danger of accidents Reduced braking efficiency due to use of non-approved brake linings.
–
Brake linings available from accessory suppliers are often not tested and approved for use on KTM vehicles. The construction
and friction factor of the brake linings and therefore the brake power can differ considerably from the original KTM brake linings. If brake linings are used that differ from the originals, there is no guarantee that they comply with the original license.
The vehicle no longer corresponds to the condition at delivery, and the warranty is no longer valid.
Warning
Environmental hazard Hazardous substances cause environmental damage.
–
Oil, grease, filters, fuel, cleaners, brake fluid, etc., should be disposed of as stipulated in applicable regulations.
BRAKES
103
Info
Never use DOT 5 brake fluid! It is silicone-based and purple in color. Oil seals and brake lines are not designed for DOT 5 brake
fluid.
Avoid contact between brake fluid and painted parts. Brake fluid attacks paint!
Use only clean brake fluid from a sealed container.
–
Stand the vehicle upright.
–
Remove screw cap 1 with membrane 2.
–
Press the brake caliper onto the brake disc by hand in order to push back the brake
piston. Make sure that no brake fluid escapes from the brake fluid reservoir. If it does,
clean it up.
Info
Make sure when pushing back the brake piston that you do not press the brake
caliper against the spokes.
101059-10
100288-10
–
Remove cotter pin 3, remove bolt 4 toward the left by striking it and remove the brake
linings.
–
Clean brake caliper and brake caliper support.
BRAKES
104
–
Check that leaf spring 5 in the brake caliper and sliding plate 6 in the brake caliper
support are seated correctly.
–
Insert the brake linings, insert the bolt and mount the cotter pin.
–
Operate the foot brake lever repeatedly until the brake linings are in contact with the
brake disc and there is a pressure point.
–
Add brake fluid to the MAX mark.
400419-11
Brake fluid DOT 4 / DOT 5.1 (
–
p. 182)
Mount the screw cap with the membrane.
Info
100289-01
Clean up overflowed or spilt brake fluid immediately with water.
WHEELS, TIRES
Removing the front wheel
12.1
105
x
Preliminary work
– Raise the motorcycle with the lift stand. (
p. 66)
Main work
– Press the brake caliper by hand on to the brake disc in order to press back the brake
pistons.
601807-10
601808-10
–
Remove screw 1.
–
Loosen screw 2.
WHEELS, TIRES
106
–
Holding the front wheel, withdraw the wheel spindle. Take the front wheel out of the
fork.
Info
Do not pull the hand brake lever when the front wheel is removed.
Always lay the wheel down in such a way that the brake disc is not damaged.
601809-10
–
Remove distance bushings 3.
800080-10
Installing the front wheel
12.2
x
Warning
Danger of accidents Reduced braking efficiency due to oil or grease on the brake discs.
–
Always keep the brake discs free of oil and grease, and clean them with brake cleaner when necessary.
WHEELS, TIRES
107
–
Check the wheel bearing for damage and wear.
»
If the wheel bearing is damaged or worn:
–
–
Replace the wheel bearing.
x
Clean and grease the shaft seal rings 1 and bearing surface A of the distance bushings.
Long-life grease (
p. 186)
–
Insert the spacers.
–
Lift the front wheel into the fork, position it, and insert the wheel spindle.
–
Mount and tighten screw 2.
800080-11
Guideline
Screw, front wheel spindle
601808-11
M24x1.5
40 Nm
(29.5 lbf ft)
–
Activate the hand brake lever multiple times until the brake linings are in contact with
the brake disc.
–
Remove the motorcycle from the lift stand. (
–
Pull the front wheel brake and push down hard on the fork several times to align the
fork legs.
–
Tighten screws 3.
p. 66)
Guideline
Screw, fork stub
M8
15 Nm
(11.1 lbf ft)
WHEELS, TIRES
Removing rear wheel
12.3
108
x
Preliminary work
– Raise the motorcycle with the lift stand. (
p. 66)
Main work
– Press the brake caliper by hand on to the brake disc in order to press back the brake
piston.
–
Remove nut 1. Remove chain adjuster 2.
–
Holding the rear wheel, withdraw the wheel spindle 3.
–
Push the rear wheel forwards as far as possible and take the chain off the rear sprocket.
100267-10
Warning
Danger of accidents Reduced braking effect caused by damaged brake discs.
–
–
100268-01
Always lay the wheel down in such a way that the brake discs are not damaged.
Take the rear wheel out of the swing arm.
Info
Do not operate the foot brake when the rear wheel is removed.
WHEELS, TIRES
Installing the rear wheel
12.4
109
x
Warning
Danger of accidents Reduced braking efficiency due to oil or grease on the brake discs.
–
Always keep the brake discs free of oil and grease, and clean them with brake cleaner when necessary.
Warning
Danger of accidents No braking effect when operating the rear brake.
–
After installing the rear wheel, always operate the foot brake until the pressure point is reached.
Preliminary work
– Raise the motorcycle with the lift stand. (
–
Remove the rear wheel.
–
Check the rear hub rubber dampers.
x(
p. 66)
p. 108)
x(
p. 110)
Main work
– Check the wheel bearing for damage and wear.
»
If the wheel bearing is damaged or worn:
–
–
Replace the wheel bearing.
Remove bushing 1. Clean and grease the working surfaces of the bushing and shaft
seal ring 2.
Long-life grease (
100269-10
–
x
p. 186)
Clean and grease the thread of the wheel spindle and nut 3.
Long-life grease (
p. 186)
–
Install the rubber damper and rear sprocket carrier in the rear wheel.
–
Place the rear wheel in the swingarm and bring the brake disc on the brake caliper into
contact.
WHEELS, TIRES
110
–
Push the rear wheel forward as far as possible and lay the chain on the rear sprocket.
–
Install the wheel spindle, the chain adjusters and the nut.
Guideline
In order that the rear wheel is correctly aligned, the markings on the left and right
chain adjusters must be in the same position relative to the reference marks A.
Info
Mount the left and right chain adjusters 4 in the same position.
100270-10
–
Tighten nut 3.
Guideline
Nut, rear wheel spindle
–
M25x1.5
Operate the foot brake lever repeatedly until the brake linings are in contact with the
brake disc and there is a pressure point.
Subsequent work
– Remove the motorcycle from the lift stand. (
Checking the rear hub rubber dampers
12.5
90 Nm
(66.4 lbf ft)
p. 66)
x
Info
The engine power is transmitted from the rear sprocket to the rear wheel via 6 rubber dampers. They eventually wear out during
operation. If the rubber dampers are not changed in time, the rear sprocket carrier and the rear hub will be damaged.
Preliminary work
– Raise the motorcycle with the lift stand. (
–
Remove the rear wheel.
x(
p. 108)
p. 66)
WHEELS, TIRES
111
Main work
– Check bearing 1.
»
If the bearing is damaged or worn:
–
–
Replace the bearings.
x
Check rubber dampers 2 of the rear hub for damage and wear.
»
If the rubber dampers of the rear hub are damaged or worn:
–
Change all rubber dampers in the rear hub.
100271-10
–
Lay the rear wheel on a workbench with the rear sprocket facing upwards and insert the
wheel spindle in the hub.
–
To check play A, hold the rear wheel tight and try to rotate the rear sprocket.
Info
Measure the play on the outside of the rear sprocket.
Play in rubber dampers, rear wheel
»
100272-10
If play A is larger than the specified value:
–
Change all rubber dampers in the rear hub.
Subsequent work
– Install the rear wheel.
–
≤ 5 mm (≤ 0.2 in)
x(
p. 109)
Remove the motorcycle from the lift stand. (
p. 66)
WHEELS, TIRES
112
Checking the tire condition
12.6
Warning
Danger of accidents Uncontrollable vehicle handling in the event of a flat tire.
–
In the interest of safety, replace damaged or worn tires immediately. (Your authorized KTM workshop will be glad to help.)
Warning
Danger of crashing Poor vehicle handling due to different tire tread patterns on front and rear wheels.
–
The front and rear wheels must be fitted with tires with similar tread patterns to prevent loss of control over the vehicle.
Warning
Danger of accidents Uncontrollable handling characteristic due to non-approved and/or non-recommended tires/wheels.
–
Only tires/wheels approved by KTM and with the corresponding speed index should be used.
Warning
Danger of accidents Reduced road grip with new tires.
–
New tires have a smooth rolling surface and therefore cannot provide full road grip. The entire rolling surface must be roughened in the first 200 kilometers (124.3 miles) by moderate riding at alternating angles. The full grip levels are not achieved
until the tires have been run in.
Info
The type, condition and air pressure of the tires all have a major impact on the riding behavior of the motorcycle.
Worn tires have a negative effect on riding behavior, especially on wet surfaces.
WHEELS, TIRES
113
–
Check the front and rear tires for cuts, run-in objects and other damage.
»
If the tires exhibit cuts, run-in objects or other damage:
–
–
Change the tires.
Check the depth of the tread.
Info
Note local national regulations concerning the minimum tread depth.
Minimum tread depth
400602-10
»
If the tread depth is less than the minimum permissible depth:
–
–
≥ 2 mm (≥ 0.08 in)
Change the tires.
Check the age of the tires.
Info
The tire's date of manufacture is usually part of the tire markings and is indicated by the last four digits of the DOT marking. The first two digits refer to the
week of manufacture and last two digits refer to the year of manufacture.
KTM recommends that the tires are changed regardless of the actual wear, at
the latest after 5 years.
»
If a tire is more than 5 years old:
–
Change the tires.
Checking the tire air pressure
12.7
Info
Low tire air pressure leads to abnormal wear and overheating of the tire.
Correct tire air pressure ensures optimal riding comfort and maximum tire service life.
WHEELS, TIRES
114
–
Remove the dust cap.
–
Check the tire air pressure when the tires are cold.
Tire air pressure, offroad, single rider
Front
1.5 bar (22 psi)
Rear
1.5 bar (22 psi)
Tire air pressure, road, solo
400695-01
Front
1.8 bar (26 psi)
Rear
1.8 bar (26 psi)
Tire air pressure with passenger / fully loaded
»
2.0 bar (29 psi)
Rear
2.2 bar (32 psi)
If the tire pressure does not meet specifications:
–
–
Front
Correct the tire pressure.
Mount the dust cap.
Checking the spoke tension
12.8
Warning
Danger of accidents Instable handling due to incorrect spoke tension.
–
Ensure that the spoke tension is correct. (Your authorized KTM workshop will be glad to help.)
WHEELS, TIRES
115
Info
A loose spoke causes wheel imbalance and rapidly leads to more loose spokes.
If the spokes are too tight, they can break due to local overload.
Check the spoke tension regularly, especially on a new motorcycle.
–
Briefly strike each spoke with a screwdriver blade.
Info
The frequency of the tone is a function of the spoke length and spoke diameter.
If you hear different tone frequencies from individual spokes of the same length
and thickness, this is an indication of different spoke tensions.
You should hear a high note.
400694-01
»
If the spoke tensions differ:
–
Correct the spoke tension.
x
ELECTRICAL SYSTEM
Removing the battery
13.1
116
x
Warning
Risk of injury Battery acid and battery gases cause serious chemical burns.
–
Keep batteries out of the reach of children.
–
Wear suitable protective clothing and goggles.
–
Avoid contact with battery acid and battery gases.
–
Keep the battery away from sparks or open flames. Charge only in well-ventilated areas.
–
In the event of skin contact, rinse with large amounts of water. If battery acid gets in the eyes, rinse with water for at least 15
minutes and contact a physician.
Preliminary work
– Switch off all power consumers and switch off the engine.
–
Remove the seat. (
p. 72)
Main work
– Disconnect the negative (minus) cable of the battery.
601812-10
–
Pull off the plug connector 1 upwards.
–
Remove screws 2.
–
Pull the retaining bracket 3 of the battery forward and remove it.
–
Take off the positive pole cover 4.
–
Disconnect the positive (plus) cable of the battery.
–
Push the wiring harness to the side and pull the battery out of the battery rack.
Info
Never operate the motorcycle with a discharged battery or without a battery. In
both cases, electrical components and safety devices can be damaged. The vehicle is therefore no longer roadworthy.
ELECTRICAL SYSTEM
Installing the battery
13.2
117
x
Main work
– Slide the battery into the battery rack.
Info
The battery terminals must be at the rear.
–
Attach the positive cable and mount positive terminal cover 1.
–
Position retaining bracket 2.
–
Mount and tighten screws 3.
601812-11
Guideline
Remaining screws, chassis
–
Plug in connector 4.
–
Attach the minus cable .
Subsequent work
– Mount the seat. (
–
Set the clock. (
p. 72)
p. 27)
M6
10 Nm (7.4 lbf ft)
ELECTRICAL SYSTEM
Recharging the battery
13.3
118
x
Warning
Risk of injury Battery acid and battery gases cause serious chemical burns.
–
Keep batteries out of the reach of children.
–
Wear suitable protective clothing and goggles.
–
Avoid contact with battery acid and battery gases.
–
Keep the battery away from sparks or open flames. Charge only in well-ventilated areas.
–
In the event of skin contact, rinse with large amounts of water. If battery acid gets in the eyes, rinse with water for at least 15
minutes and contact a physician.
Warning
Environmental hazard The battery contains elements that are harmful to the environment.
–
Do not discard batteries with the household trash. Dispose of a defective battery in an environmentally compatible manner.
Give the battery to your KTM dealer or to a recycling center that accepts used batteries.
Warning
Environmental hazard Hazardous substances cause environmental damage.
–
Oil, grease, filters, fuel, cleaners, brake fluid, etc., should be disposed of as stipulated in applicable regulations.
ELECTRICAL SYSTEM
119
Info
Even when there is no load on the battery, it still loses power steadily.
The charge state and the type of charge are very important for the service life of the battery.
Rapid recharging with a high charging current shortens the battery's service life.
If the charging current, charging voltage and charging time are exceeded, electrolyte escapes through the safety valves. This
reduces the battery capacity.
If the battery is depleted from starting the vehicle repeatedly, the battery must be charged immediately.
If the battery is left in a discharged state for an extended period, it will become over-discharged and sulfate, destroying the battery.
The battery is maintenance-free, which means that the acid level does not need to be checked.
Preliminary work
– Switch off all power consumers and switch off the engine.
–
Switch off all power consumers and switch off the engine.
–
Remove the seat. (
–
Remove the battery.
p. 72)
x(
p. 116)
ELECTRICAL SYSTEM
120
Main work
– Connect the battery charger to the battery. Switch on the battery charger.
Battery charger (58429074000)
You can also use the battery charger to test rest potential and start potential of the battery, and to test the alternator. With this device, you cannot overcharge the battery.
Info
Never remove lid 1.
Charge the battery with a maximum of 10% of the capacity specified on the battery housing 2.
–
Switch off and disconnect the charger after charging.
Guideline
The charge current, charge voltage and charge time must not be exceeded.
Charge the battery regularly when the
motorcycle is not in use
100151-10
Subsequent work
– Install the battery.
–
Mount the seat. (
–
Set the clock. (
x(
p. 117)
p. 72)
p. 27)
3 months
ELECTRICAL SYSTEM
121
Changing the main fuse
13.4
Warning
Fire hazard The electrical system can be overloaded if the wrong fuses are used.
–
Use only fuses with the prescribed amperage. Never by-pass or repair fuses.
Info
The main fuse protects all power consumers in the vehicle. It is in the housing of the starter relay next to the battery.
Preliminary work
– Switch off all power consumers and switch off the engine.
–
Remove the seat. (
p. 72)
Main work
– Remove protection covers 1.
601791-10
ELECTRICAL SYSTEM
122
–
Remove a defective main fuse 2 with needle nose pliers.
–
Install a new main fuse.
Fuse (58011109130) (
p. 173)
Info
A reserve fuse 3 is located in the starter relay.
601792-10
–
Check that the electrical equipment is functioning properly.
–
Mount the protection covers.
Follow-up work
– Mount the seat. (
–
Set the clock. (
p. 72)
p. 27)
Changing fuses of individual power consumers
13.5
Info
The fuse box containing the fuses of individual power consumers is located under the seat.
Preliminary work
– Switch off all power consumers and switch off the engine.
–
Remove the seat. (
p. 72)
ELECTRICAL SYSTEM
123
Main work
– Open fuse box cover 1.
601791-11
–
Remove the defective fuse.
Guideline
Fuse 1 - 10 A - ignition, combination instrument
Fuse 2 - 10 A - clock, ignition (EFI control unit)
Fuse 3 - 10 A - throttle valve control unit
Fuse 4 - 10 A - fuel pump
Fuse 5 - 10 A - radiator fan
Fuse 6 - 10 A - horn, brake light, turn signal
Fuse 7 - 15 A - high beam, low beam, parking light, tail light, license plate lamp
Fuse 8 - 10 A - for supplementary equipment (accessories connected with ignition
switch)
Fuse 9 - 10 A - for accessories (permanent positive)
Fuse 10 - not used
Fuse SPARE - 10 A/15 A - spare fuses
Info
A defective fuse is indicated by a burned-out fuse wire A.
600606-10
ELECTRICAL SYSTEM
124
Warning
Fire hazard The electrical system can be overloaded if the wrong fuses are
used.
–
–
Use only fuses with the prescribed amperage. Never by-pass or repair fuses.
Replace with a spare fuse of the right rating.
Fuse (75011088010) (
p. 173)
Fuse (75011088015) (
p. 173)
Tip
Put a new spare fuse in the fuse box for future use if needed.
–
Check the function of power consumers.
–
Close the fuse box cover.
Follow-up work
– Mount the seat. (
p. 72)
Removing the headlight mask with the headlight
13.6
Preliminary work
– Switch off all power consumers and switch off the engine.
ELECTRICAL SYSTEM
125
Main work
– Cover the fender with a cloth to protect it from damage.
–
Remove screws 1 on the left and right.
–
Tip the headlight mask forward and pull it off in an upward direction.
–
Disconnect the connectors of turn signals 2 and headlight 3.
–
Put down the headlight mask.
601793-10
601794-10
ELECTRICAL SYSTEM
126
Installing the headlight mask with the headlight
13.7
–
Connect the connectors of headlight 1 and turn signal lights 2.
–
Check lighting function.
–
Remove the cloth from the fender, attach the headlight mask to points 3 on the fender
and swing it up to the steering head.
601794-11
601810-10
ELECTRICAL SYSTEM
127
–
Position brake-hose guide 4. Mount and tighten screws 5.
Guideline
Screw, headlight mask
M5
5 Nm (3.7 lbf ft)
601793-11
Changing the headlight bulb
13.8
Note
Damage to reflector Reduced luminance.
–
Grease on the lamp will evaporate due to the heat and be deposited on the reflector. Clean the lamp and keep it free of grease before
mounting.
Preliminary work
– Switch off all power consumers and switch off the engine.
–
Remove the headlight mask with the headlight. (
p. 124)
ELECTRICAL SYSTEM
128
Main work
– Pull off connector 1.
–
Take off rubber cap 2 of the headlight bulb.
–
Detach spring bar 3.
–
Remove headlight bulb 4.
–
Insert a new headlight bulb into the headlight housing.
600610-10
Headlight (H4 / socket P43t) (
p. 173)
–
Fix the headlight bulb in the headlight using the spring bar.
–
Replace the rubber cap. Attach the connector.
600611-10
Follow-up work
– Install the headlight mask with the headlight. (
p. 126)
Changing the parking light bulb
13.9
Note
Damage to reflector Reduced luminance.
–
Grease on the lamp will evaporate due to the heat and be deposited on the reflector. Clean the lamp and keep it free of grease before
mounting.
ELECTRICAL SYSTEM
129
Preliminary work
– Switch off all power consumers and switch off the engine.
–
Remove the headlight mask with the headlight. (
p. 124)
Main work
– Remove rubber cap 1.
600610-12
–
Pull bulb socket 2 out of the reflector.
–
Pull parking light bulb 3 out of the bulb socket.
–
Insert a new parking light bulb in the bulb socket.
Parking light (W5W / socket W2.1x9.5d) (
–
Insert the bulb socket in the reflector.
–
Insert the rubber cap.
p. 173)
600612-10
Follow-up work
– Install the headlight mask with the headlight. (
p. 126)
ELECTRICAL SYSTEM
130
Changing the turn signal bulb
13.10
Note
Damage to reflector Reduced luminance.
–
Grease on the lamp will evaporate due to the heat and be deposited on the reflector. Clean the lamp and keep it free of grease before
mounting.
Main work
– Remove the screw on the rear of the turn signal housing.
–
Tilt headlamp diffuser 1 forward carefully and take it off.
–
Lightly squeeze the orange plug 2 in the area of the holding lugs and take it off.
–
Press the turn signal bulb carefully into the socket, turn it counterclockwise by about
30°, and take it out of the socket.
Info
Do not touch the reflector with your fingers, and keep it free from grease.
601795-10
–
Press the new turn signal bulb carefully into the socket and turn it clockwise until it
stops.
Turn signal (R10W / socket BA15s) (
p. 173)
–
Mount the orange plug.
–
Position the diffuser.
–
Insert the screw and turn it counterclockwise first until it engages in the thread. Tighten
the screw slightly.
Follow-up work
– Check that the turn signal system is functioning properly.
ELECTRICAL SYSTEM
131
Checking the headlight setting
13.11
A
0
–
Stand the vehicle upright on a horizontal surface in front of a light wall and make a
mark at the height of the center of the low beam headlight.
–
Make another mark at a distance B under the first mark.
Guideline
0
B
Distance B
–
5 cm (2 in)
Position the vehicle vertically at a distance A in front of the wall.
Guideline
Distance A
400726-10
5 m (16 ft)
–
The rider, with luggage and a passenger if applicable, now sits down on the motorcycle.
–
Switch on the low beam.
–
Check the headlight setting.
For a ready-to-operate motorcycle with a rider, and with luggage and a passenger if
applicable, the light-dark boundary must lie exactly on the lower mark.
»
If the boundary between light and dark does not meet specifications:
–
Adjust the headlight range. (
p. 131)
Adjusting the headlight range
13.12
Preliminary work
– Check the headlight setting. (
p. 131)
ELECTRICAL SYSTEM
132
Main work
– Turn adjusting screw 1 to adjust the headlight range.
Guideline
For a motorcycle with rider, the light/dark boundary must be exactly on the lower
mark (made in: Checking headlight adjustment).
Info
601796-10
Turn clockwise to increase the headlight range; turn counterclockwise to reduce
the headlight range.
If you have a heavy payload, you will need to correct the headlight range.
COOLING SYSTEM
133
Cooling system
14.1
The water pump 1 in the engine forces the coolant to flow.
The pressure in the cooling system resulting from heat is regulated by a valve in the radiator cap 2. The heat expansion causes the surplus coolant to flow into the compensating
tank 3. When the temperature falls, this surplus coolant is sucked back into the cooling
system. This permits the specified coolant temperature without causing any malfunctions.
125 °C (257 °F)
600614-10
Cooling takes place by means of the air stream and a radiator fan 4, which is controlled by
a thermoswitch.
The lower the speed, the less the cooling effect. Dirty cooling fins also reduce the cooling
effect.
400407-10
Checking the antifreeze and coolant level
14.2
Warning
Danger of scalding During motorcycle operation, the coolant gets very hot and is under pressure.
–
Do not remove the radiator cap, radiator hoses or other cooling system components when the engine is hot. Allow the engine
and cooling system to cool down. In case of scalding, rinse immediately with lukewarm water.
COOLING SYSTEM
134
Warning
Danger of poisoning Coolant is poisonous and a health hazard.
–
Avoid contact between coolant and skin, eyes and clothing. If it gets into your eyes, rinse immediately with water and contact
a doctor. Wash affected skin areas immediately with soap and water. If coolant is swallowed, contact a doctor immediately.
Change clothes that have come into contact with coolants. Keep coolant out of the reach of children.
Condition
Engine is cold.
–
Stand the motorcycle on its side stand on a horizontal surface.
–
Remove the cap of the compensating tank 1.
–
Check antifreeze of coolant.
−25… −45 °C (−13… −49 °F)
»
If the antifreeze of the coolant does not meet specifications:
–
–
Correct the antifreeze of the coolant.
Check the coolant level in the compensating tank.
601798-10
The coolant level must be within the range shown in the figure.
»
If the coolant level does not meet specifications:
–
Correct the coolant level.
Alternative 1
Coolant (
p. 182)
Alternative 2
Coolant (mixed ready to use) (
–
Mount the cap of the compensating tank.
p. 182)
COOLING SYSTEM
135
–
Screw off the radiator cap 2.
–
Check antifreeze of coolant.
−25… −45 °C (−13… −49 °F)
»
If the antifreeze of the coolant does not meet specifications:
–
–
Correct the antifreeze of the coolant.
Check the coolant level in the radiator.
The radiator must be completely filled.
601799-10
»
If the coolant level does not meet specifications:
–
Correct the coolant level and find out the cause of the loss.
Alternative 1
Coolant (
p. 182)
Alternative 2
Coolant (mixed ready to use) (
–
p. 182)
Mount the radiator cap.
Checking the coolant level
14.3
Warning
Danger of scalding During motorcycle operation, the coolant gets very hot and is under pressure.
–
Do not remove the radiator cap, radiator hoses or other cooling system components when the engine is hot. Allow the engine
and cooling system to cool down. In case of scalding, rinse immediately with lukewarm water.
COOLING SYSTEM
136
Warning
Danger of poisoning Coolant is poisonous and a health hazard.
–
Avoid contact between coolant and skin, eyes and clothing. If it gets into your eyes, rinse immediately with water and contact
a doctor. Wash affected skin areas immediately with soap and water. If coolant is swallowed, contact a doctor immediately.
Change clothes that have come into contact with coolants. Keep coolant out of the reach of children.
Condition
Engine is cold.
–
Stand the motorcycle on its side stand on a horizontal surface.
–
Check the coolant level in the compensating tank 1.
The coolant level must be within the range shown in the figure.
»
If the coolant level does not meet specifications:
–
Correct the coolant level.
Alternative 1
Coolant (
601798-10
p. 182)
Alternative 2
Coolant (mixed ready to use) (
–
p. 182)
Screw off the radiator cap 2 and check the coolant level in the radiator.
The radiator must be completely filled.
»
If the coolant level does not meet specifications:
–
Correct the coolant level and find out the cause of the loss.
Alternative 1
Coolant (
601799-10
p. 182)
COOLING SYSTEM
137
Alternative 2
Coolant (mixed ready to use) (
–
Draining the coolant
14.4
p. 182)
Mount the radiator cap.
x
Warning
Danger of scalding During motorcycle operation, the coolant gets very hot and is under pressure.
–
Do not remove the radiator cap, radiator hoses or other cooling system components when the engine is hot. Allow the engine
and cooling system to cool down. In case of scalding, rinse immediately with lukewarm water.
Warning
Danger of poisoning Coolant is poisonous and a health hazard.
–
Avoid contact between coolant and skin, eyes and clothing. If it gets into your eyes, rinse immediately with water and contact
a doctor. Wash affected skin areas immediately with soap and water. If coolant is swallowed, contact a doctor immediately.
Change clothes that have come into contact with coolants. Keep coolant out of the reach of children.
Preliminary work
– Stand the motorcycle on its side stand on a horizontal surface.
–
Remove the engine guard. (
p. 86)
COOLING SYSTEM
138
Main work
– Stand the motorcycle upright.
–
Place a suitable container under the engine.
–
Remove screw 1. Take off the radiator cap.
–
Completely drain the coolant.
–
Mount screw 1 with a new seal ring and tighten it.
Guideline
Plug, drain hole of water pump
600616-10
Follow-up work
– Install the engine guard. (
Filling the cooling system
14.5
M10x1
15 Nm
(11.1 lbf ft)
p. 87)
x
Warning
Danger of poisoning Coolant is poisonous and a health hazard.
–
Avoid contact between coolant and skin, eyes and clothing. If it gets into your eyes, rinse immediately with water and contact
a doctor. Wash affected skin areas immediately with soap and water. If coolant is swallowed, contact a doctor immediately.
Change clothes that have come into contact with coolants. Keep coolant out of the reach of children.
COOLING SYSTEM
139
–
Stand the motorcycle on its side stand on a horizontal surface.
–
Remove radiator cap 1.
–
Refill the coolant.
601799-11
Alternative 1
Coolant (
p. 182)
Alternative 2
Coolant (mixed ready to use) (
p. 182)
–
Fill the radiator completely with coolant. Mount radiator cap 1.
–
Remove the cap from compensating tank 2 and add coolant to the level shown in the
figure.
–
Mount the cap of the compensating tank.
601800-10
Danger
Danger of poisoning Exhaust gases are poisonous and inhaling them may result
in unconsciousness and/or death.
–
601798-11
When running the engine, always make sure there is sufficient ventilation,
and do not start or run the engine in an enclosed space without an effective
exhaust extraction system.
COOLING SYSTEM
140
–
Start the engine and run it until the 5th bar of the temperature indicator lights up.
–
Switch off the engine and allow it to cool down.
–
After the engine has cooled down, check the coolant level in the radiator and in the
compensating tank again and add more coolant if necessary.
TUNING THE ENGINE
141
Checking the play in the throttle cable
15.1
–
Check the throttle grip for smooth operation.
–
Move the handlebar to the straight-ahead position. Move the throttle grip backwards
and forwards to ascertain the play in the throttle cable.
Throttle cable play
»
3… 5 mm (0.12… 0.2 in)
If the throttle cable play does not meet specifications:
–
Adjust the play in the throttle cable.
x(
p. 142)
Danger
400192-10
Danger of poisoning Exhaust gases are poisonous and inhaling them may result
in unconsciousness and/or death.
–
–
When running the engine, always make sure there is sufficient ventilation,
and do not start or run the engine in an enclosed space without an effective
exhaust extraction system.
Start the engine and let it run idle. Move the handlebar to and fro over the entire steering range.
The idle speed must not change.
»
If the idle speed changes:
–
Adjust the play in the throttle cable.
x(
p. 142)
TUNING THE ENGINE
Adjusting the play in the throttle cable
15.2
142
x
–
Move the handlebar to the straight-ahead position.
–
Use the KTM diagnostics tool to set the motor drive to the basic position.
–
Loosen counter nut 1.
–
Set the play in the throttle cable by turning the adjusting screw 2.
Guideline
Throttle cable play
–
3… 5 mm (0.12… 0.2 in)
Tighten counter nut 1.
100280-10
Adjusting the engine characteristic
15.3
Preliminary work
– Switch off the ignition by turning the ignition key to position OFF
–
Remove the seat. (
.
p. 72)
Main work
– Pull the Map‑Select switch and holder 1 upward off of the retaining bracket.
–
601801-10
Pull the Map‑Select switch out of the holder.
TUNING THE ENGINE
143
–
Turn the adjusting wheel until the desired digit is next to marking 2.
Set the Map‑Select switch to Soft.
– Set the adjusting wheel to position 1.
Soft – reduced homologated peak performance for better driveability.
Set the Map‑Select switch to Advanced.
– Set the adjusting wheel to position 2.
Advanced – homologated performance with extremely direct responsiveness.
601802-10
Set the Map‑Select switch to Standard.
– Set the adjusting wheel to position 3, 4, 5, 6, 7, 8 or 9.
Standard – homologated performance with balanced responsiveness.
Set the Map‑Select switch to poor fuel quality.
– Set the adjusting wheel to position 0.
Poor fuel quality – homologated performance is reduced in accordance with the
fuel quality, use for no more than 1 tank of fuel
–
Position the Map‑Select switch in the holder.
–
Slide the Map‑Select switch with the holder downward onto the retaining bracket.
Subsequent work
– Mount the seat. (
p. 72)
TUNING THE ENGINE
144
Checking the basic position of the shift lever
15.4
–
Sit on the vehicle in the riding position and determine distance A between the upper
edge of your boot and the shift lever.
Distance between shift lever and upper
edge of boot
»
A
0
If the distance does not meet specifications:
–
Adjust the basic position of the shift lever.
400692-10
Adjusting the basic position of the shift lever
15.5
–
601815-10
10… 20 mm (0.39… 0.79 in)
x
Remove screw 1 and take off shift lever 2.
x(
p. 144)
TUNING THE ENGINE
145
–
Clean gear teeth A of the shift lever and shift shaft.
–
Mount the shift lever 2 on the shift shaft in the required position and engage the gearing.
Info
The range of adjustment is limited.
The shift lever must not come into contact with any other vehicle components
during the shift procedure.
601814-10
–
Mount and tighten screw 1.
Guideline
Screw, shift lever
M6
14 Nm
(10.3 lbf ft)
Loctite® 222
SERVICE WORK ON THE ENGINE
146
Checking the engine oil level
16.1
Info
The engine oil level must be checked when the engine is warm.
Condition
The engine is at operating temperature.
Preliminary work
– Stand the motorcycle upright on a horizontal surface.
Main work
– Check the engine oil level.
Info
After switching off the engine, wait one minute before checking the level.
The engine oil must be between the lower and upper edge of the oil level viewer.
»
601818-10
If the engine oil level is not at the specified level:
–
Add the engine oil. (
p. 153)
SERVICE WORK ON THE ENGINE
147
Changing the engine oil and filter, cleaning the oil screens
16.2
–
–
–
–
–
x
Drain the engine oil. x ( p. 147)
Remove the oil filter. x ( p. 148)
Clean the oil screens. x ( p. 150)
Install the oil filter. x ( p. 152)
Fill up with engine oil. x ( p. 152)
601022-10
Draining the engine oil
16.3
x
Warning
Danger of scalding Engine oil and gear oil get very hot when the motorcycle is ridden.
–
Wear appropriate protective clothing and safety gloves. In case of burns, rinse immediately with lukewarm water.
Warning
Environmental hazard Hazardous substances cause environmental damage.
–
Oil, grease, filters, fuel, cleaners, brake fluid, etc., should be disposed of as stipulated in applicable regulations.
Info
Drain the engine oil only when the engine is warm.
Preliminary work
– Stand the motorcycle on its side stand on a horizontal surface.
–
Remove the engine guard. (
p. 86)
SERVICE WORK ON THE ENGINE
148
Main work
– Place a suitable container under the engine.
–
Remove the oil drain plug 1 with the magnet and seal ring.
–
Completely drain the engine oil.
–
Thoroughly clean the oil drain plug with a magnet.
–
Mount the oil drain plug with the magnet and seal ring and tighten it.
100200-10
Guideline
Oil drain plug with magnet
M12x1.5
20 Nm
(14.8 lbf ft)
100201-01
Removing the oil filter
16.4
x
Warning
Danger of scalding Engine oil and gear oil get very hot when the motorcycle is ridden.
–
Wear appropriate protective clothing and safety gloves. In case of burns, rinse immediately with lukewarm water.
SERVICE WORK ON THE ENGINE
Warning
Environmental hazard Hazardous substances cause environmental damage.
–
Oil, grease, filters, fuel, cleaners, brake fluid, etc., should be disposed of as stipulated in applicable regulations.
Preliminary work
– Place a suitable container under the engine.
Main work
– Remove screws 1. Remove the oil filter cover 2 with the O-ring.
–
Pull oil filter 3 out of the oil filter housing.
Circlip pliers reverse (51012011000)
100202-10
–
Remove screws 4. Remove oil filter 5 with the O-ring.
–
Pull oil filter 6 out of the oil filter housing.
Circlip pliers reverse (51012011000)
100203-10
–
Completely drain the engine oil.
–
Thoroughly clean the parts and sealing area.
149
SERVICE WORK ON THE ENGINE
Cleaning the oil screens
16.5
x
Warning
Danger of scalding Engine oil and gear oil get very hot when the motorcycle is ridden.
–
Wear appropriate protective clothing and safety gloves. In case of burns, rinse immediately with lukewarm water.
Warning
Environmental hazard Hazardous substances cause environmental damage.
–
Oil, grease, filters, fuel, cleaners, brake fluid, etc., should be disposed of as stipulated in applicable regulations.
Preliminary work
– Place a suitable container under the engine.
Main work
– Remove plug 1 with oil screen 2 and the O-rings.
100205-10
150
SERVICE WORK ON THE ENGINE
151
–
Remove plug 3 with oil screen 4 and the O-rings.
–
Completely drain the remaining engine oil.
–
Thoroughly clean the parts and sealing area.
–
Position oil screen 2 with the O-rings.
–
Mount and tighten screw plug 1 with the O-ring.
100206-10
Guideline
Plug, oil screen
M20x1.5
15 Nm
(11.1 lbf ft)
100207-10
–
Position oil screen 4 with the O-rings.
–
Mount and tighten screw plug 3 with the O-ring.
Guideline
Plug, oil screen
100208-10
M20x1.5
15 Nm
(11.1 lbf ft)
SERVICE WORK ON THE ENGINE
Installing the oil filter
16.6
152
x
–
Insert oil filters 1 and 2.
–
Oil the O-rings of the oil filter covers. Mount oil filter covers 3 and 4.
–
Mount and tighten the screws.
Guideline
Screw, oil filter cover
M5
6 Nm (4.4 lbf ft)
100204-10
Filling up with engine oil
16.7
x
Info
Too little engine oil or poor-quality engine oil results in premature wear to the engine.
Main work
– Remove filler plug with O-ring 1 from the clutch cover and add engine oil.
Engine oil
1.70 l (1.8 qt.)
Engine oil (SAE 10W/60)
(00062010035) ( p. 183)
Alternative engine
oil
–
100209-10
Refit plug with O-ring 1 and tighten it.
Engine oil
(SAE 10W/50)
( p. 183)
SERVICE WORK ON THE ENGINE
153
Danger
Danger of poisoning Exhaust gases are poisonous and inhaling them may result
in unconsciousness and/or death.
–
–
When running the engine, always make sure there is sufficient ventilation,
and do not start or run the engine in an enclosed space without an effective
exhaust extraction system.
Start the engine and check that it is oil-tight.
Subsequent work
– Install the engine guard. (
–
Check the engine oil level. (
p. 87)
p. 146)
Adding engine oil
16.8
Info
Too little engine oil or poor-quality engine oil results in premature wear to the engine.
Main work
– Remove the oil filler plug 1 with the O-ring from the clutch cover and fill up with
engine oil.
Engine oil (SAE 10W/60) (00062010035) (
Engine oil (SAE 10W/50) (
p. 183)
p. 183)
Info
100209-10
For optimal performance of the engine oil, do not mix different types of engine
oil.
If appropriate, change the engine oil.
SERVICE WORK ON THE ENGINE
–
154
Install and tighten the oil filler plug 1 with the O-ring.
Danger
Danger of poisoning Exhaust gases are poisonous and inhaling them may result
in unconsciousness and/or death.
–
–
When running the engine, always make sure there is sufficient ventilation,
and do not start or run the engine in an enclosed space without an effective
exhaust extraction system.
Start the engine and check that it is oil-tight.
Subsequent work
– Check the engine oil level. (
p. 146)
CLEANING, CARE
155
Cleaning the motorcycle
17.1
Note
Material damage Damage and destruction of components by high-pressure cleaning equipment.
–
Never clean the vehicle with high-pressure cleaning equipment or a strong water-jet. The excessive pressure can penetrate electrical
components, socket connects, throttle cables, and bearings, etc., and can damage or destroy these parts.
Warning
Environmental hazard Hazardous substances cause environmental damage.
–
Oil, grease, filters, fuel, cleaners, brake fluid, etc., should be disposed of as stipulated in applicable regulations.
Info
If you clean the motorcycle regularly, its value and appearance will be maintained over a long period.
Avoid direct sunshine on the motorcycle during cleaning.
Main work
– Seal the exhaust system to keep water out.
–
First remove coarse dirt particles with a gentle spray of water.
–
Spray very dirty areas with a normal motorcycle cleaner and then clean with a brush.
Motorcycle cleaner (
p. 187)
Info
401061-01
Clean the vehicle using a soft sponge and warm water containing normal motorcycle cleaner.
If the vehicle was operated in road salt, clean it with cold water. Warm water
enhances the corrosive effects of salt.
CLEANING, CARE
156
–
After rinsing the motorcycle with a gentle spray of water, allow it to dry thoroughly.
Warning
Danger of accidents Reduced braking efficiency due to wet or dirty brakes.
–
–
Clean or dry dirty or wet brakes by riding and braking gently.
After cleaning, ride the vehicle a short distance until the engine is warm, applying the
brakes occasionally.
Info
The heat produced causes water at inaccessible locations in the engine and the
brakes to evaporate.
–
Push back the protection covers of the handlebar controls to allow any water that has
penetrated to evaporate.
Follow-up work
– After the motorcycle has cooled off, lubricate all moving parts and bearings.
–
Clean the chain. (
–
Treat bare metal parts (except for brake discs and exhaust system) with anti-corrosion
materials.
p. 75)
Cleaning and preserving materials for metal, rubber and plastic (
–
Treat all painted parts with a mild paint polish.
High-luster polish for paint (
–
p. 186)
p. 186)
Treat all plastic parts and powder-coated parts with a mild cleaning and care agent.
Paint cleaner and polish for high-gloss and matte finishes, bare metal and plastic
surfaces ( p. 187)
–
Oil the ignition/steering lock.
CLEANING, CARE
157
Universal oil spray (
p. 187)
Checks and maintenance steps for winter operation
17.2
Info
If you use the motorcycle in winter, you must expect salt on the roads. You should therefore take precautions against aggressive
road salt.
If the vehicle was operated in road salt, clean it with cold water after riding. Warm water would enhance the corrosive effects of
salt.
–
Clean the motorcycle. (
–
Clean the brakes.
p. 155)
Info
After EVERY trip on salted roads, thoroughly wash the brake calipers and brake
linings with cold water and dry carefully. This should be done after the parts are
cooled down and while they are installed.
After use on salted roads, clean the motorcycle thoroughly with cold water and
dry it properly.
401060-01
–
Treat the engine, the swingarm, and all other bare or galvanized parts (except brake
discs) with a wax-based anti-corrosion substance.
Info
To prevent serious reduction of the braking efficiency, make sure no
anti-corrosion substance gets on to the brake discs.
–
Clean the chain. (
p. 75)
STORAGE
158
Storage
18.1
Info
If you want to garage the motorcycle for a longer period, take the following actions.
Before storing the motorcycle, check all parts for function and wear. If service, repairs, or replacements are necessary, you should
do this during the storage period (less workshop overload). In this way, you can avoid long workshop waiting times at the start of the
new season.
401058-01
–
Make sure the tank is as empty as possible so that you can fill up with fresh fuel when
you put the motorcycle back into operation.
–
Clean the motorcycle. (
–
Change the engine oil and filter, clean the oil screens.
–
Check the antifreeze and coolant level. (
–
Check the tire air pressure. (
–
Remove the battery.
–
Recharge the battery.
p. 155)
x(
x(
x(
p. 147)
p. 133)
p. 113)
p. 116)
p. 118)
Guideline
Storage temperature of battery without
direct sunshine
–
0… 35 °C (32… 95 °F)
Store the vehicle in a dry location that is not subject to large fluctuations in temperature.
Info
KTM recommends jacking up the motorcycle.
–
Raise the motorcycle with the lift stand. (
–
Cover the motorcycle with a tarp or similar cover that is permeable to air.
p. 66)
STORAGE
159
Info
Do not use non-porous materials since they prevent humidity from escaping,
thus causing corrosion.
Avoid running the engine for a short time only. Since the engine cannot warm
up properly, the water vapor produced during combustion condenses and causes
valves and exhaust system to rust.
Preparing for use after storage
18.2
401059-01
–
Remove the motorcycle from the lift stand. (
–
Recharge the battery.
–
Install the battery.
–
Set the clock. (
–
Refuel. (
–
Perform checks and vehicle care when preparing for use. (
–
Take a test ride.
x(
x(
p. 66)
p. 118)
p. 117)
p. 27)
p. 48)
p. 40)
TROUBLESHOOTING
160
Faults
Possible cause
Action
The engine does not turn when the
starter button is pressed
Operating error
–
Carry out the start procedure. (
Battery is discharged
–
Recharge the battery.
Fuse 1, 2, 3 or 4 is blown
–
Change the fuses of individual power consumers.
( p. 122)
Engine turns only if the clutch lever is
drawn
Engine turns but does not start.
x(
p. 118)
Main fuse burned out
–
Change the main fuse. (
No ground connection present.
–
Check the ground connection.
The vehicle is in gear
–
Shift gear to neutral.
The vehicle is in gear and the side
stand is folded out
–
Shift gear to neutral.
p. 41)
p. 121)
Operating error
–
Carry out the start procedure. (
Fuse 4 blown
–
Change the fuses of individual power consumers.
( p. 122)
Coupling of fuel hose connection not
connected
–
Reconnect coupling of fuel hose connection.
Socket connector of wiring harness is
oxidized
–
Clean the socket connector and treat it with contact spray.
Defect in fuel injection system
–
Read out the fault memory using the KTM diagnostics tool.
Air filter is very dirty
–
Remove the air filter.
–
Install the air filter.
p. 41)
x
Engine has too little power.
Engine overheats.
x ( p. 73)
x ( p. 74)
Check the fuel pressure. x
Read out the fault memory using the KTM diagnostics tool. x
Fuel filter is very dirty
–
Defect in fuel injection system
–
Too little coolant in cooling system
–
Check the cooling system for leakage.
–
Check the coolant level. (
p. 135)
TROUBLESHOOTING
161
Faults
Possible cause
Action
Engine overheats.
Radiator fins very dirty
–
Clean radiator fins.
Foam formation in cooling system
–
Drain the coolant.
–
Fill the cooling system.
FI warning lamp (MIL) lights/flashes
x(
p. 137)
x(
Change the radiator hose. x
Check the thermostat. x
p. 138)
Buckled or damaged radiator hose
–
Thermostat is faulty
–
Fuse 5 blown
–
Change the fuses of individual power consumers.
( p. 122)
Defect in radiator fan system
–
Check the radiator fan system.
x
Air in cooling system
–
Fill the cooling system.
p. 138)
Defect in fuel injection system
–
Read out the fault memory using the KTM diagnostics tool.
x(
x
Engine dies during the journey
High oil consumption
Lack of fuel
–
Refuel. (
Fuse 1, 2 or 4 blown
–
Change the fuses of individual power consumers.
( p. 122)
Engine vent hose bent
–
Route the vent hose without bends or change it if
necessary.
p. 48)
Engine oil level too high
–
Check the engine oil level. (
Engine oil too thin (low viscosity)
–
Change the engine oil and filter, clean the oil
screens.
( p. 147)
p. 146)
x
Headlight and parking light not functioning
Fuse 7 blown
–
Change the fuses of individual power consumers.
( p. 122)
Turn signal, brake light and horn not
functioning
Fuse 6 blown
–
Change the fuses of individual power consumers.
( p. 122)
TROUBLESHOOTING
162
Faults
Possible cause
Action
Time is not (correctly) displayed
Fuse 2 blown
–
Change the fuses of individual power consumers.
( p. 122)
–
Set the clock. (
Ignition not switched off when vehicle
was parked
–
Recharge the battery.
Battery is not charged by alternator
–
Check the charging voltage.
Battery discharged
–
Combination instrument shows nothing
in the display
Fuse 1 blown
Speedometer in combination instrument not functioning
Speedometer wiring harness is damaged or plug-in connection is oxidized
p. 27)
x(
p. 118)
x
Check the quiescent current. x
–
Change the fuses of individual power consumers.
( p. 122)
–
Set the clock. (
–
Check the wiring harness and plug-in connection.
p. 27)
BLINK CODE
163
Blink code FI of warning lamp
(MIL)
02 FI warning lamp (MIL) flashes briefly 2x
Error level condition
Crankshaft position sensor - circuit fault
Blink code FI of warning lamp
(MIL)
06 FI warning lamp (MIL) flashes briefly 6x
Error level condition
Throttle position sensor circuit A - input signal too low
Blink code FI of warning lamp
(MIL)
09 FI warning lamp (MIL) flashes briefly 9x
Error level condition
Manifold absolute pressure sensor cylinder 1 - input signal too low
Manifold absolute pressure sensor cylinder 1 - input signal too high
Blink code FI of warning lamp
(MIL)
12 FI warning lamp (MIL) flashes 1x long, 2x short
Error level condition
Engine coolant temperature sensor - input signal too low
Engine coolant temperature sensor - input signal too high
Blink code FI of warning lamp
(MIL)
13 FI warning lamp (MIL) flashes 1x long, 3x short
Error level condition
Intake air temperature sensor - input signal too low
Intake air temperature sensor - input signal too high
BLINK CODE
164
Blink code FI of warning lamp
(MIL)
14 FI warning lamp (MIL) flashes 1x long, 4x short
Error level condition
Ambient air pressure sensor - input signal too low
Ambient air pressure sensor - input signal too high
Blink code FI of warning lamp
(MIL)
15 FI warning lamp (MIL) flashes 1x long, 5x short
Error level condition
Rollover sensor - input signal too low
Rollover sensor - input signal too high
Blink code FI of warning lamp
(MIL)
17 FI warning lamp (MIL) flashes 1x long, 7x short
Error level condition
Lambda sensor cylinder 1, sensor 1 - circuit fault
Blink code FI of warning lamp
(MIL)
24 FI warning lamp (MIL) flashes 2x long, 4x short
Error level condition
System voltage - circuit fault
Blink code FI of warning lamp
(MIL)
25 FI warning lamp (MIL) flashes 2x long, 5x short
Error level condition
Side stand switch - circuit fault
BLINK CODE
165
Blink code FI of warning lamp
(MIL)
26 FI warning lamp (MIL) flashes 2x long, 6x short
Error level condition
Motor drive hall sensor - circuit fault
Blink code FI of warning lamp
(MIL)
37 FI warning lamp (MIL) flashes 3x long, 7x short
Error level condition
Ignition coil 1, cylinder 1 - circuit fault
Blink code FI of warning lamp
(MIL)
41 FI warning lamp (MIL) flashes 4x long, 1x short
Error level condition
Fuel pump controller - short circuit to ground or open circuit
Fuel pump controller - input signal too high
Blink code FI of warning lamp
(MIL)
45 FI warning lamp (MIL) flashes 4x long, 5x short
Error level condition
Lambda sensor heater cylinder 1, sensor 1 - short circuit to ground or open circuit
Lambda sensor heater cylinder 1, sensor 1 - input signal too high
Blink code FI of warning lamp
(MIL)
54 FI warning lamp (MIL) flashes 5x long, 4x short
Error level condition
Secondary air valve - short circuit to ground or open circuit
BLINK CODE
166
Blink code FI of warning lamp
(MIL)
58 FI warning lamp (MIL) flashes 5x long, 8x short
Error level condition
EPT motor drive relay permission - signal fault
Blink code FI of warning lamp
(MIL)
60 FI warning lamp (MIL) flashes 6x long
Error level condition
Motor drive - circuit fault
Blink code FI of warning lamp
(MIL)
90 FI warning lamp (MIL) flashes 9x long
Error level condition
Throttle position - circuit fault
Blink code FI of warning lamp
(MIL)
91 FI warning lamp (MIL) flashes 9x long, 1x short
Error level condition
CAN bus communication error
Blink code FI of warning lamp
(MIL)
92 FI warning lamp (MIL) flashes 9x long, 2x short
Error level condition
Motor drive voltage (internal) - circuit fault
TECHNICAL DATA - ENGINE
167
Design
1-cylinder 4-stroke engine, water-cooled
Displacement
690 cm³ (42.11 cu in)
Stroke
84.5 mm (3.327 in)
Bore
102 mm (4.02 in)
Compression ratio
12.5:1
Idle speed
Coolant temperature: ≥ 70 °C (≥ 158 °F)
1,550… 1,650 rpm
Control
OHC, 4 valves controlled via rocker arm, chain drive
Valve diameter, intake
40 mm (1.57 in)
Valve diameter, exhaust
34 mm (1.34 in)
Valve play, cold
0.07… 0.13 mm (0.0028… 0.0051 in)
Crankshaft bearing
2 roller bearings
Conrod bearing
Needle bearing
Piston pin bearing
Piston pin with DLC coating
Pistons
Forged light alloy
Piston rings
1 L-ring, 1 tapered compression piston ring, 1 oil scraper ring
Engine lubrication
Semi-dry sump lubrication with two rotor pumps
Primary transmission
36:79
Clutch
APTC™ Antihopping clutch in oil bath / hydraulically operated
Gearbox
6-gears, claw-shifted
Transmission ratio
1st gear
14:35
2nd gear
16:28
3rd gear
21:28
4th gear
21:23
TECHNICAL DATA - ENGINE
168
5th gear
23:22
6th gear
23:20
Mixture preparation
Electronic fuel injection
Ignition
Contactless controlled fully electronic ignition with digital ignition
adjustment
Alternator
12 V, 224 W
Spark plug
NGK LKAR 8AI - 9
Spark plug electrode gap
0.9 mm (0.035 in)
Cooling
Water cooling, permanent circulation of coolant by water pump
Starting aid
Electric starter, automatic decompressor
Capacity - engine oil
21.1
Engine oil
1.70 l (1.8 qt.)
Engine oil (SAE 10W/60) (00062010035) (
Alternative engine oil
Engine oil (SAE 10W/50)
( p. 183)
Capacity - coolant
21.2
Coolant
1.20 l (1.27 qt.)
Coolant (
p. 182)
Coolant (mixed ready to use) (
p. 183)
p. 182)
TECHNICAL DATA - ENGINE TIGHTENING TORQUES
169
Oil hole plug
EJOT
9 Nm (6.6 lbf ft)
Loctite® 243™
Screw, membrane fixation
M3
2.5 Nm (1.84 lbf ft)
Loctite® 243™
Hose clamp, intake flange
M4
1.5 Nm (1.11 lbf ft)
–
Oil nozzle for conrod bearing lubrication
M4
2 Nm (1.5 lbf ft)
Loctite® 243™
Locking screw for bearing
M5
6 Nm (4.4 lbf ft)
Loctite® 243™
Screw, breather cover on valve cover
M5
3 Nm (2.2 lbf ft)
Loctite® 243™
Screw, clutch spring
M5
6 Nm (4.4 lbf ft)
–
Screw, cover plate for oil return line
M5
6 Nm (4.4 lbf ft)
–
Screw, gear sensor
M5
5 Nm (3.7 lbf ft)
Loctite® 243™
Screw, oil filter cover
M5
6 Nm (4.4 lbf ft)
–
Screw, oil pump cover
M5
6 Nm (4.4 lbf ft)
Loctite® 243™
Plug, vacuum connection
M6
10 Nm (7.4 lbf ft)
Loctite® 243™
Screw in alternator cover
M6
10 Nm (7.4 lbf ft)
–
Screw, alternator cover (chain shaft
through-hole)
M6
10 Nm (7.4 lbf ft)
Loctite® 243™
Screw, autodecompression
M6
3… 4 Nm (2.2… 3 lbf ft)
Loctite® 243™
Screw, axial lock of camshaft
M6
10 Nm (7.4 lbf ft)
Loctite® 243™
Screw, clutch cover
M6
10 Nm (7.4 lbf ft)
–
Screw, clutch slave cylinder
M6x20
10 Nm (7.4 lbf ft)
Loctite® 243™
Screw, clutch slave cylinder
M6x35
10 Nm (7.4 lbf ft)
–
Screw, cylinder
M6
10 Nm (7.4 lbf ft)
Loctite® 243™
Screw, cylinder head
M6
10 Nm (7.4 lbf ft)
Loctite® 243™
Screw, engine case
M6
10 Nm (7.4 lbf ft)
–
Screw, ignition pulse generator
M6
10 Nm (7.4 lbf ft)
Loctite® 243™
TECHNICAL DATA - ENGINE TIGHTENING TORQUES
170
Screw, locking lever
M6
10 Nm (7.4 lbf ft)
Loctite® 243™
Screw, rocker arm shaft
M6
12 Nm (8.9 lbf ft)
–
Screw, shift drum locating
M6
10 Nm (7.4 lbf ft)
Loctite® 243™
Screw, shift lever
M6
14 Nm (10.3 lbf ft)
Loctite® 222
Screw, starter motor
M6
10 Nm (7.4 lbf ft)
Loctite® 243™
Screw, stator
M6
10 Nm (7.4 lbf ft)
Loctite® 243™
Screw, thermostat housing
M6
10 Nm (7.4 lbf ft)
Loctite® 243™
Screw, timing chain guide rail
M6
10 Nm (7.4 lbf ft)
Loctite® 243™
Screw, timing chain tensioning rail
M6
10 Nm (7.4 lbf ft)
Loctite® 243™
Screw, valve cover
M6
10 Nm (7.4 lbf ft)
–
Screw, water pump cover
M6
10 Nm (7.4 lbf ft)
–
Screw, water pump wheel
M6
10 Nm (7.4 lbf ft)
Loctite® 243™
Oil jet, piston cooling
M6x0.75
4 Nm (3 lbf ft)
Loctite® 243™
Plug, crankshaft location
M8
20 Nm (14.8 lbf ft)
–
Stud, exhaust flange
M8
10 Nm (7.4 lbf ft)
Loctite® 243™
Cylinder head screw
M10
Tightening sequence:
Tighten diagonally, beginning
with the rear screw on the
chain shaft.
Step 1
15 Nm (11.1 lbf ft)
Step 2
30 Nm (22.1 lbf ft)
Step 3
45 Nm (33.2 lbf ft)
Step 4
60 Nm (44.3 lbf ft)
Lubricated with engine oil
TECHNICAL DATA - ENGINE TIGHTENING TORQUES
171
Oil hole plug
M10x1
15 Nm (11.1 lbf ft)
Loctite® 243™
Plug, drain hole of water pump
M10x1
15 Nm (11.1 lbf ft)
–
Plug, oil bore for oil radiator
M10x1
15 Nm (11.1 lbf ft)
–
Screw, unlocking of timing chain tensioner
M10x1
10 Nm (7.4 lbf ft)
–
Spark plug
M12x1.25
17 Nm (12.5 lbf ft)
–
Coolant temperature sensor on cylinder
head
M12x1.5
12 Nm (8.9 lbf ft)
–
Oil drain plug with magnet
M12x1.5
20 Nm (14.8 lbf ft)
–
Oil pressure regulator valve plug
M12x1.5
20 Nm (14.8 lbf ft)
–
Plug, oil bore
M14x1.5
15 Nm (11.1 lbf ft)
Loctite® 243™
Engine case stud
M16x1.5
25 Nm (18.4 lbf ft)
Loctite® 243™
Rotor nut
M18x1.5
100 Nm (73.8 lbf ft)
–
Nut, engine sprocket
M20x1.5
80 Nm (59 lbf ft)
Loctite® 243™
Nut, inner clutch hub
M20x1.5
100 Nm (73.8 lbf ft)
Loctite® 243™
Nut, primary gear
M20LHx1.5
90 Nm (66.4 lbf ft)
Loctite® 243™
Plug, oil screen
M20x1.5
15 Nm (11.1 lbf ft)
–
Plug, timing chain tensioner
M20x1.5
25 Nm (18.4 lbf ft)
–
Plug, oil thermostat
M24x1.5
15 Nm (11.1 lbf ft)
–
Screw in alternator cover
M24x1.5
8 Nm (5.9 lbf ft)
–
TECHNICAL DATA - CHASSIS
172
Frame
Lattice frame made of chrome molybdenum steel tubing, powdercoated
Fork
WP Suspension 4860 MXMA
Shock absorber
WP Suspension 4618 with Pro‑Lever deflector
Suspension travel
Front
250 mm (9.84 in)
Rear
250 mm (9.84 in)
Brake system
Front
Disc brake with dual-piston brake caliper, floating
Rear
Disc brake with single-piston brake caliper, floating
Brake discs - diameter
Front
300 mm (11.81 in)
Rear
240 mm (9.45 in)
Brake discs - wear limit
Front
4.5 mm (0.177 in)
Rear
3.5 mm (0.138 in)
Tire air pressure, road, solo
Front
1.8 bar (26 psi)
Rear
1.8 bar (26 psi)
Tire air pressure with passenger / fully loaded
Front
2.0 bar (29 psi)
Rear
2.2 bar (32 psi)
Tire air pressure, offroad, single rider
Front
1.5 bar (22 psi)
Rear
1.5 bar (22 psi)
TECHNICAL DATA - CHASSIS
173
Secondary drive ratio
15:45
Chain
5/8 x 1/4” X‑ring
Steering head angle
63°
Wheelbase
1,504±15 mm (59.21±0.59 in)
Seat height unloaded
935 mm (36.81 in)
Ground clearance unloaded
280 mm (11.02 in)
Weight without fuel, approx.
142 kg (313 lb.)
Maximum permissible front axle load
150 kg (331 lb.)
Maximum permissible rear axle load
200 kg (441 lb.)
Maximum permissible overall weight
350 kg (772 lb.)
Battery
YTZ10S
Battery voltage: 12 V
Nominal capacity: 8.6 Ah
maintenance-free
Fuse
58011109130
30 A
Fuse
75011088015
15 A
Fuse
75011088010
10 A
Headlight
H4 / socket P43t
12 V
60/55 W
Parking light
W5W / socket W2.1x9.5d
12 V
5W
Instrument lights and indicator lamps
LED
Turn signal
R10W / socket BA15s
Lighting equipment
23.1
12 V
10 W
TECHNICAL DATA - CHASSIS
174
Brake/tail light
LED
License plate lamp
W5W / socket W2.1x9.5d
12 V
5W
Front tire
Rear tire
Condition
90/90 - 21 M/C 54S M+S TT
Continental TKC 80
140/80 - 18 M/C 70R M+S TT
Continental TKC 80
To max.: 160 km/h (99.4 mph)
Tires
23.2
Additional information is available in the Service section under:
http://www.ktm.com
Capacity - fuel
23.3
Total fuel tank capacity, approx.
Fuel reserve, approx.
12 l (3.2 US gal)
Super unleaded (ROZ 95/RON 95/PON 91) (
2.5 l (2.6 qt.)
p. 185)
TECHNICAL DATA - FORK
175
Fork part number
14.18.7L.10
Fork
WP Suspension 4860 MXMA
Compression damping
Comfort
20 clicks
Standard
15 clicks
Sport
10 clicks
Full payload
10 clicks
Rebound damping
Comfort
20 clicks
Standard
15 clicks
Sport
10 clicks
Full payload
10 clicks
Spring length with preload spacer(s)
472 mm (18.58 in)
Spring rate
Soft
5.2 N/mm (29.7 lb/in)
Medium (standard)
5.4 N/mm (30.8 lb/in)
Hard
5.6 N/mm (32 lb/in)
Air chamber length
120±20 mm (4.72±0.79 in)
Fork length
890 mm (35.04 in)
Fork oil per fork leg
615 ml (20.79 fl. oz.)
Fork oil (SAE 5) (
p. 184)
TECHNICAL DATA - SHOCK ABSORBER
Shock absorber part number
15.18.7L.10
Shock absorber
WP Suspension 4618 with Pro‑Lever deflector
Compression damping, high-speed
Comfort
2 turns
Standard
1.5 turns
Sport
1 turn
Full payload
1 turn
Compression damping, low-speed
Comfort
20 clicks
Standard
15 clicks
Sport
10 clicks
Full payload
10 clicks
Rebound damping
Comfort
20 clicks
Standard
15 clicks
Sport
10 clicks
Full payload
10 clicks
Spring preload
20 mm (0.79 in)
Spring rate
Medium (standard)
80 N/mm (457 lb/in)
Hard
85 N/mm (485 lb/in)
Spring length
220 mm (8.66 in)
Gas pressure
10 bar (145 psi)
Static sag
18 mm (0.71 in)
Riding sag
70… 80 mm (2.76… 3.15 in)
176
TECHNICAL DATA - SHOCK ABSORBER
Fitted length
Shock absorber oil (
395 mm (15.55 in)
p. 184)
SAE 2.5
177
TECHNICAL DATA - CHASSIS TIGHTENING TORQUES
178
Screw, chain guard
EJOT
2 Nm (1.5 lbf ft)
–
Screw, combination instrument
EJOT
1 Nm (0.7 lbf ft)
–
Screw, license plate holder, bottom
EJOT
3 Nm (2.2 lbf ft)
–
Screw, side cover on spoiler
EJOT
1 Nm (0.7 lbf ft)
–
Screw, side stand switch
EJOT
2 Nm (1.5 lbf ft)
–
Screw, SLS valve
EJOT
2 Nm (1.5 lbf ft)
–
Fitting, side stand switch
M4
2 Nm (1.5 lbf ft)
–
Screw, fuel hose clamp on fuel tank
M4
2 Nm (1.5 lbf ft)
–
Screw, wheel speed sensor
M4
2 Nm (1.5 lbf ft)
Loctite® 243™
Spoke nipple, front wheel
M4.5
3… 6 Nm (2.2… 4.4 lbf ft)
–
Bolt, foot brake lever stub
M5
6 Nm (4.4 lbf ft)
Loctite® 243™
Remaining nuts, chassis
M5
4 Nm (3 lbf ft)
–
Remaining screws, chassis
M5
4 Nm (3 lbf ft)
–
Screw, brake line holder on swingarm
M5
Initial screw connection
8 Nm (5.9 lbf ft)
Subsequent screw connection
4 Nm (3 lbf ft)
–
Screw, cable on starter motor
M5
3 Nm (2.2 lbf ft)
–
Screw, electrical holder
M5
3 Nm (2.2 lbf ft)
–
Screw, exhaust heat shield
M5
8 Nm (5.9 lbf ft)
Loctite® 243™
Screw, fuel level sensor
M5
3 Nm (2.2 lbf ft)
–
Screw, fuel pump
M5
4 Nm (3 lbf ft)
–
Screw, fuel tank closure flange
M5
2.5 Nm (1.84 lbf ft)
–
Screw, headlight mask
M5
5 Nm (3.7 lbf ft)
–
TECHNICAL DATA - CHASSIS TIGHTENING TORQUES
Screw, pressure regulator
M5
179
4 Nm (3 lbf ft)
–
Spoke nipple, rear wheel
M5
3… 6 Nm (2.2… 4.4 lbf ft)
–
Remaining nuts, chassis
M6
10 Nm (7.4 lbf ft)
–
Remaining screws on fuel tank
M6
5 Nm (3.7 lbf ft)
–
Remaining screws, chassis
M6
10 Nm (7.4 lbf ft)
–
Screw connection, foot brake cylinder
M6
10 Nm (7.4 lbf ft)
–
Screw, air filter box top
M6
2 Nm (1.5 lbf ft)
–
Screw, ball joint of push rod on foot
brake cylinder
M6
10 Nm (7.4 lbf ft)
Loctite® 243™
Screw, brake fluid reservoir of rear brake
M6
5 Nm (3.7 lbf ft)
–
Screw, chain guard
M6
2 Nm (1.5 lbf ft)
Loctite® 243™
Screw, chain guide
M6
8 Nm (5.9 lbf ft)
–
Screw, chain sliding guard
M6
8 Nm (5.9 lbf ft)
Loctite® 243™
Screw, fan hood
M6
4 Nm (3 lbf ft)
–
Screw, front brake disc
M6
14 Nm (10.3 lbf ft)
Loctite® 243™
Screw, ignition lock
M6
10 Nm (7.4 lbf ft)
Loctite® 243™
Screw, lower radiator bracket
M6
8 Nm (5.9 lbf ft)
–
Screw, magnetic holder on side stand
M6
6 Nm (4.4 lbf ft)
Loctite® 243™
Screw, radiator guard
M6
8 Nm (5.9 lbf ft)
–
Screw, rear brake disc
M6
14 Nm (10.3 lbf ft)
Loctite® 243™
Screw, seat lock
M6
5 Nm (3.7 lbf ft)
–
Screw, side cover
M6
5 Nm (3.7 lbf ft)
–
Screw, upper radiator bracket
M6
10 Nm (7.4 lbf ft)
–
Screw, voltage regulator
M6
8 Nm (5.9 lbf ft)
–
Nut, manifold on cylinder head
M8
20 Nm (14.8 lbf ft)
Copper paste
TECHNICAL DATA - CHASSIS TIGHTENING TORQUES
180
Nut, rear sprocket screw
M8
35 Nm (25.8 lbf ft)
Loctite® 2701
Remaining nuts, chassis
M8
25 Nm (18.4 lbf ft)
–
Remaining screws, chassis
M8
25 Nm (18.4 lbf ft)
–
Screw, bottom triple clamp
M8
12 Nm (8.9 lbf ft)
–
Screw, chain sliding piece
M8
15 Nm (11.1 lbf ft)
–
Screw, connection lever on frame
M8
30 Nm (22.1 lbf ft)
Loctite® 243™
Screw, exhaust clamp on main silencer
M8
12 Nm (8.9 lbf ft)
–
Screw, foot brake lever
M8
25 Nm (18.4 lbf ft)
Loctite® 243™
Screw, fork stub
M8
15 Nm (11.1 lbf ft)
–
Screw, front brake caliper
M8
25 Nm (18.4 lbf ft)
Loctite® 243™
Screw, front footrest bracket
M8
25 Nm (18.4 lbf ft)
–
Screw, fuel tank bracket
M8
15 Nm (11.1 lbf ft)
–
Screw, fuel tank, bottom
M8
25 Nm (18.4 lbf ft)
Loctite® 243™
Screw, fuel tank, top
M8
25 Nm (18.4 lbf ft)
Loctite® 243™
Screw, handlebar clamp
M8
20 Nm (14.8 lbf ft)
–
Screw, handrail
M8
20 Nm (14.8 lbf ft)
–
Screw, heel protector
M8x12
8 Nm (5.9 lbf ft)
–
Screw, license plate holder, top
M8
20 Nm (14.8 lbf ft)
–
Screw, main silencer holder
M8
25 Nm (18.4 lbf ft)
–
Screw, main silencer holder on fuel tank
M8
25 Nm (18.4 lbf ft)
–
Screw, rear footrest bracket
M8x16
25 Nm (18.4 lbf ft)
–
Screw, side stand bracket
M8
25 Nm (18.4 lbf ft)
Loctite® 243™
Screw, spring holder on side stand
bracket
M8
25 Nm (18.4 lbf ft)
Loctite® 243™
TECHNICAL DATA - CHASSIS TIGHTENING TORQUES
Screw, steering stem
M8
181
20 Nm (14.8 lbf ft)
–
Screw, top triple clamp
M8
17 Nm (12.5 lbf ft)
–
Engine carrying screw
M10
45 Nm (33.2 lbf ft)
Loctite® 243™
Remaining nuts, chassis
M10
45 Nm (33.2 lbf ft)
–
Remaining screws, chassis
M10
45 Nm (33.2 lbf ft)
–
Screw, bottom shock absorber
M10
45 Nm (33.2 lbf ft)
Loctite® 243™
Screw, engine bearer on frame
M10
45 Nm (33.2 lbf ft)
–
Screw, handlebar support
M10
40 Nm (29.5 lbf ft)
Loctite® 243™
Screw, side stand
M10
35 Nm (25.8 lbf ft)
Loctite® 243™
Screw, top shock absorber
M10
45 Nm (33.2 lbf ft)
Loctite® 243™
Screw, swingarm pivot
M12
80 Nm (59 lbf ft)
–
Lambda sensor
M12x1.25
25 Nm (18.4 lbf ft)
Copper paste
Nut, linkage lever on swingarm
M14x1.5
100 Nm (73.8 lbf ft)
–
Nut, linkage lever to rocker arm
M14x1.5
100 Nm (73.8 lbf ft)
–
Screw, bottom steering head
M20x1.5
60 Nm (44.3 lbf ft)
Loctite® 243™
Screw, top steering head
M20x1.5
12 Nm (8.9 lbf ft)
–
Screw, front wheel spindle
M24x1.5
40 Nm (29.5 lbf ft)
–
Nut, rear wheel spindle
M25x1.5
90 Nm (66.4 lbf ft)
–
SUBSTANCES
182
Brake fluid DOT 4 / DOT 5.1
According to
– DOT
Guideline
– Use only brake fluid that complies with the specified standard (see specifications on the container) and that possesses the corresponding properties. KTM recommends Castrol and Motorex® products.
Supplier
Castrol
– RESPONSE BRAKE FLUID SUPER DOT 4
Motorex®
– Brake Fluid DOT 5.1
Coolant
Guideline
– Use only suitable coolant (also in countries with high temperatures). Use of low-quality antifreeze can lead to corrosion and foaming.
KTM recommends Motorex® products.
Mixture ratio
Antifreeze protection: −25… −45 °C (−13…
−49 °F)
50 % corrosion inhibitor/antifreeze
50 % distilled water
Coolant (mixed ready to use)
Antifreeze
Supplier
Motorex®
– COOLANT G48
−40 °C (−40 °F)
SUBSTANCES
183
Engine oil (SAE 10W/60) (00062010035)
According to
– JASO T903 MA (
–
SAE (
–
KTM LC4 2007+
p. 188)
p. 188) (SAE 10W/60)
Guideline
– Use only engine oils that comply with the specified standards (see specifications on the container) and that possess the corresponding
properties. KTM recommends Motorex® products.
Synthetic engine oil
Supplier
Motorex®
– Motorex® KTM Cross Power 4T
Engine oil (SAE 10W/50)
According to
– JASO T903 MA (
–
SAE (
p. 188)
p. 188) (SAE 10W/50)
Guideline
– Use only engine oils that comply with the specified standards (see specifications on the container) and that possess the corresponding
properties. KTM recommends Motorex® products.
Fully synthetic engine oil
Supplier
Motorex®
– Power Synt 4T
SUBSTANCES
184
Fork oil (SAE 5)
According to
– SAE ( p. 188) (SAE 5)
Guideline
– Use only oils that comply with the specified standards (see specifications on the container) and that possess the corresponding properties. KTM recommends Motorex® products.
Supplier
Motorex®
– Racing Fork Oil
Hydraulic fluid (15)
According to
– ISO VG (15)
Guideline
– Use only hydraulic oil that complies with the specified standard (see specifications on the container) and that possesses the corresponding properties. KTM recommends Motorex® products.
Supplier
Motorex®
– Hydraulic Fluid 75
Shock absorber oil (SAE 2.5) (50180342S1)
According to
– SAE ( p. 188) (SAE 2.5)
Guideline
– Use only oils that comply with the specified standards (see specifications on the container) and that possess the corresponding properties.
SUBSTANCES
Super unleaded (ROZ 95/RON 95/PON 91)
According to
– DIN EN 228 (ROZ 95/RON 95/PON 91)
Guideline
– Only use unleaded super fuel that matches or is equivalent to the specified fuel grade.
–
Fuel with an ethanol content of up to 10 % (E10 fuel) is safe to use.
Info
Do not use fuel containing methanol (e. g. M15, M85, M100) or more than 10 % ethanol (e. g. E15, E25, E85, E100).
185
AUXILIARY SUBSTANCES
Chain cleaner
Guideline
– KTM recommends Motorex® products.
Supplier
Motorex®
– Chain Clean
Cleaning and preserving materials for metal, rubber and plastic
Guideline
– KTM recommends Motorex® products.
Supplier
Motorex®
– Protect & Shine
High-luster polish for paint
Guideline
– KTM recommends Motorex® products.
Supplier
Motorex®
– Moto Polish
Long-life grease
Guideline
– KTM recommends Motorex® products.
Supplier
Motorex®
– Bike Grease 2000
186
AUXILIARY SUBSTANCES
Motorcycle cleaner
Guideline
– KTM recommends Motorex® products.
Supplier
Motorex®
– Moto Clean 900
Off-road chain spray
Guideline
– KTM recommends Motorex® products.
Supplier
Motorex®
– Chainlube Offroad
Paint cleaner and polish for high-gloss and matte finishes, bare metal and plastic surfaces
Guideline
– KTM recommends Motorex® products.
Supplier
Motorex®
– Clean & Polish
Universal oil spray
Guideline
– KTM recommends Motorex® products.
Supplier
Motorex®
– Joker 440 Synthetic
187
STANDARDS
188
JASO T903 MA
Different technical development directions required a new specification for 4-stroke motorcycles – the JASO T903 MA Standard. Earlier, engine oils from the automobile industry were used for 4-stroke motorcycles because there was no separate motorcycle specification.
Whereas long service intervals are demanded for automobile engines, high performance at high engine speeds are in the foreground for
motorcycle engines. With most motorcycles, the gearbox and the clutch are lubricated with the same oil as the engine. The JASO MA Standard meets these special requirements.
SAE
The SAE viscosity classes were defined by the Society of Automotive Engineers and are used for classifying oils according to their viscosity. The viscosity describes only one property of oil and says nothing about quality.
INDEX
189
rear brake, checking . . . . . . . . . . . . . . . . . . . . . . . . . . 101
INDEX
A
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Air filter
installing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
removing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Antifreeze
checking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133
B
Baggage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Battery
fitting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117
recharging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
removing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116
Blink code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163-166
Brake discs
checking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
Brake fluid
front brake, adding . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
rear brake, adding . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
Brake fluid level
front brake, checking . . . . . . . . . . . . . . . . . . . . . . . . . . 90
rear brake, checking . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
Brake linings
front brake, changing . . . . . . . . . . . . . . . . . . . . . . . . . . 93
front brake, checking . . . . . . . . . . . . . . . . . . . . . . . . . . 92
rear brake, changing . . . . . . . . . . . . . . . . . . . . . . . . . . 101
Brakes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Braking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
C
Chain
checking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
dirt, checking for . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Chain guide
adjusting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
checking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
Chain tension
adjusting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
checking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
Chassis number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Clutch
checking/correcting fluid level . . . . . . . . . . . . . . . . . . . . 85
Clutch lever . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
basic position, adjusting . . . . . . . . . . . . . . . . . . . . . . . . 85
Combination instrument . . . . . . . . . . . . . . . . . . . . . . . . . . .
clock, setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
coolant temperature indicator . . . . . . . . . . . . . . . . . . . .
display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
function buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
indicator lamps . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ODO display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
23
. 27
. 30
. 25
. 24
. 24
. 28
INDEX
190
setting kilometers or miles . . .
speed display . . . . . . . . . . . .
time . . . . . . . . . . . . . . . . . .
TRIP 1 display, setting/resetting
TRIP 2 display, setting/resetting
TRIP F display . . . . . . . . . . . .
Coolant
draining
....
....
....
...
...
....
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
. 26
. 26
. 27
. 28
. 29
. 30
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137
Coolant level
checking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133, 135
Cooling system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133
filling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138
D
Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
E
Electric starter button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Emergency OFF switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Engine
running in . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Engine oil
adding .
changing
draining
refilling .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
Engine oil level
checking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146
Engine sprocket
checking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
Environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
F
Filler cap
closing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
opening . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Filling up
fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Foot brake lever . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
basic position, adjusting . . . . . . . . . . . . . . . . . . . . . . . . 97
free travel, checking . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
Engine guard
installing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
removing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
Fork . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
compression damping, adjusting . . . . . . . . . . . . . . . . . .
dust boots, cleaning . . . . . . . . . . . . . . . . . . . . . . . . . .
fork legs, bleeding . . . . . . . . . . . . . . . . . . . . . . . . . . .
rebound, adjusting . . . . . . . . . . . . . . . . . . . . . . . . . . .
Engine number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Fork part number
Engine characteristic
adjusting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142
153
147
147
152
54
. 54
. 67
. 67
. 55
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
INDEX
191
Fork protector
positioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
remove . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Front wheel
installing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
removing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
Fuel, oils, etc. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Fuse
of individual power consumer, changing . . . . . . . . . . . . . 122
Ignition lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Indicator lamps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
K
Key number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
L
Light switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Loading the vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
M
H
Hand brake lever . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
free travel, adjusting . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
free travel, checking . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
Handlebar position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
adjusting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Handrails . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Headlight
light range, adjusting
I
. . . . . . . . . . . . . . . . . . . . . . . . . 131
Headlight bulb, changing . . . . . . . . . . . . . . . . . . . . . . . . . . 127
Headlight mask with headlight
installing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126
removing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124
Headlight setting, checking . . . . . . . . . . . . . . . . . . . . . . . . . 131
Horn button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Main fuse
changing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121
Motorcycle
cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155
raising with lift stand . . . . . . . . . . . . . . . . . . . . . . . . . . 66
removing from lift stand . . . . . . . . . . . . . . . . . . . . . . . . 66
O
Oil filter
changing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147
installing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152
removing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 148
Oil screens
cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147, 150
Owner's manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
P
Parking
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
INDEX
192
Parking light bulb
changing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128
Passenger footrests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Play in throttle cable
adjusting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142
checking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141
Preparing for use
after storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159
checks and vehicle care when preparing for use . . . . . . . . 40
Putting into operation
advice on first use
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
R
Rear hub rubber dampers
checking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
Rear sprocket
checking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
Rear wheel
installing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
removing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
Riding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
starting off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Riding sag
adjusting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
S
Seat
mounting
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
removing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Seat release . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Service schedule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51-53
Shift lever . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
basic position, adjusting . . . . . . . . . . . . . . . . . . . . . . . 144
basic position, checking . . . . . . . . . . . . . . . . . . . . . . . 144
Shifting
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Shock absorber . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
compression damping, general . . . . . . . . . . . . . . . . . . .
compression damping, high-speed, adjusting . . . . . . . . .
compression damping, low-speed, adjusting . . . . . . . . . .
rebound damping, adjusting . . . . . . . . . . . . . . . . . . . . .
riding sag, checking . . . . . . . . . . . . . . . . . . . . . . . . . .
spring preload, adjusting . . . . . . . . . . . . . . . . . . . . . . .
static sag, checking . . . . . . . . . . . . . . . . . . . . . . . . . .
54
. 56
. 57
. 56
. 58
. 61
. 61
. 60
Shock absorber part number . . . . . . . . . . . . . . . . . . . . . . . . . 18
Side stand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Spare parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Spoke tension
checking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114
Starting
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Steering head bearing play
adjusting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
checking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Steering lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Stopping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
INDEX
Storage
193
right rear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 158
T
W
Technical data
chassis . . . . . . . . . . . . .
chassis tightening torques
engine . . . . . . . . . . . . .
engine tightening torques
fork . . . . . . . . . . . . . . .
shock absorber . . . . . . . .
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
172-174
178-181
167-168
169-171
. . . . 175
176-177
Throttle grip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Tire air pressure
checking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
Tire condition
checking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112
Transport . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160-162
Turn signal bulb
changing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130
Turn signal switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Type label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
U
Use definition
...................................8
V
View of vehicle
front left . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Winter operation
checks and maintenance steps . . . . . . . . . . . . . . . . . . . 157
Work rules
.....................................9
*3211787en*
3211787en
01/2012
KTM-Sportmotorcycle AG
5230 Mattighofen/Austria
http://www.ktm.com
Photo: Mitterbauer

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement