Martin Alien 05 Recessed User Manual

martinarchitectural
user manual
05 Driver
Measurements are in millimeters
104
345
43
375
360
Ø4
Ø7.5
60
© 2002 Martin Professional A/S, Denmark.
All rights reserved. No part of this manual may be reproduced, in any form or by any means, without permission in writing from Martin Professional A/S, Denmark.
Printed in Denmark.
P/N 35000107, Rev D
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Safety information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Configuring and installing an Alien 05 system . . . . . . . . . . . 6
05 Driver location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Powering the 05 Driver. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Powering Alien 05s . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Control network cabling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Connecting an Oracle control device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Connecting a DMX control device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
General operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Control methods. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
LED indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Oracle control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Playback. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
DMX configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
DMX modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
DMX address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Stand-alone control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Set-up. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Firmware updates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Fuse replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
DMX protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
DMX address settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Stand-alone settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
6-pin DIP-switch settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
3
Introduction
1
Thank you for selecting the Martin 05 Driver. The 05 Driver is part of the
Alien 05 system of color changers. The 05 Driver contains the electronics
that control and operate connected Alien 05 luminaires.
The Alien 05 Series is made up of the following products:
05 Driver
Contains the intelligent control functions, and a mains
power relay. Every Alien 05 system must have at
least one 05 Driver. An 05 Driver can control up to 24
Alien 05 luminaires (of all models). This number can
be extended with the use of 05 Repeaters.
Alien 05
Recessed
Recessed ceiling or wall luminaires for use outside of
the United States.
Alien 05
Eyeball
Recessed ceiling or wall luminaires for use in the
United States. Designed for mounting in a Cooper
Lighting, Halo brand, recessed, low-volt, non-IC
fixture housing (item # H7LVT).
Alien 05 Stem Arm-mounted luminaires that are designed to be
Mount
hung from a ceiling. Several arm lengths and bases
(with built-in dimmable transformers) are available.
05 Repeater
A signal amplifier that enables an additional 24 Alien
05 luminaires to be controlled from a single 05 Driver.
Oracle
A dedicated control unit for the Alien 05 series.
Note that in this document we refer to Alien 05 Recessed, Alien 05 Eyeball
and Alien 05 Stem Mount models collectively as “Alien 05” luminaires.
4
Introduction
S a f e t y i n f o r ma t i o n
Warning!
This product is not for household use.
Read this manual before powering or installing the device, follow the safety
precautions listed below and observe all warnings in this manual and on the
housing. If you have questions about how to operate the system safely,
contact your Martin dealer or call the Martin 24-hour service hotline at +45
70 200 201.
•
•
•
•
Install only in a dry area.
Refer electrical installation to a qualified electrician.
Refer all service to a Martin technician.
Use only a source of AC power that complies with local building and
electrical codes and has both overload and ground-fault protection.
• Disconnect the device from AC power before removing the cover.
• Never operate the device without the cover installed.
• Do not modify the device.
Introduction
5
Configuring and
installing an Alien
05 system
2
The following sections in this chapter describe rules and concepts needed
to design and implement an Alien 05 installation - specifically regrading data
and power. The following tasks are described:
•
•
•
•
•
•
Positioning the 05 Driver; see “05 Driver location” on page 6.
Connecting power to the 05 Driver; see page 7.
Connecting power to the Alien 05 luminaires; see page 7.
Setting up a control network; see page 10.
Connecting an Oracle control device; see page 12.
Connecting a DMX control device; see page 13.
05 Driver location
Once the Alien system is set-up and running, there should be no need to
access the 05 Driver; it may be installed in any convenient location that
meets the following conditions:
• The cable run to the Oracle remote interface, if used, does not exceed 40
meters (130 ft.).
• The data cable run from any connector on an 05 Driver to the last connected
fixture does not exceed 40 meters (130 ft.) - unless the signal is amplified by
an 05 Repeater.
• The ambient temperature does not exceed 40° C (104° F).
• The unit is protected from moisture.
Four 7 mm (1/3 in.) holes are provided on the 05 Driver casing for fixed
installation.
6
Configuring and installing an Alien 05 system
Powering the 05 Driver
The 05 Driver features an auto-ranging power supply. It is suitable for use
with 90 - 250 V, 50/60 Hz mains supplies.
Use round, 3-conductor 0.75 mm2 (18 AWG) or better electrical cable with
an outside diameter of 5 - 6 mm (3/16 - 1/4 in.) for connection to the AC
power supply.
Warning!
For protection from dangerous electric shock, the fixture must
be grounded (earthed). The AC mains supply shall be fitted with
a fuse or circuit breaker, ground-fault protection, and a means
to isolate the fixture from the mains during service or when not
in use. Refer electrical installation to a qualified electrician.
Connecting the AC mains lead
1 Verify that the mains lead (not included) is isolated from AC power.
2 Remove top cover. Feed wire through the opening in the front panel labelled
“90 - 250V~ Mains Input”.
3 Connect the mains lead to the connection block as shown on top cover.
4 Replace the top cover.
Powering Alien 05s
Each Alien 05 draws 50 watts of power at 4.2 amps from an electronic
transformer that supplies 12 volt AC at 50 or 60 hertz (only supplied with
bases for the Alien 05 Stem Mount). If you are installing multiple Alien 05s
you can use one or more transformers, specified to the number of Alien 05s
power is being supplied to.
Warning:
The cable length between transformers and the Alien 05
luminaires that they supply power to must not be more than 45
cm (17.7 in.).
Note:
Alien 05 Eyeball models draw their power via the transformer
that is built into the Halo Recessed fixture housing in which
they will be installed. These transformers can draw power
through the 05 Driver’s 10 amp mains relay but the transformers
cannot be dimmed.
Configuring and installing an Alien 05 system
7
S am p l e c o n f i gu r a t i o n s
The following sub-sections illustrate three possible configurations.
Simple power-supply configuration
In the simplest configuration, the 05 Driver is connected directly to the local
mains supply, and the Alien 05s are supplied power from a single, or
multiple, transformer/s connected to mains supply.
Max
45 cm
Driver
12V AC
Trans
.
Mains
80-250V AC
50/60 Hz
Mains
In this configuration the 05 Driver cannot control the supply of power to the
Alien 05 luminaires or dim them.
R e m o t e l a m p o n / of f p o w er - s u p p l y c o n f i g u r a t i o n
In this configuration a transformer, or transformers, supplying 12V AC power
to one or more Alien 05s, is connected to the 10A mains relay on the 05
Driver.
This enables remote control of power on and off of the Alien 05s via either
an Oracle controller or DMX control device, that is attached to the 05 Driver
(when the intensity channel is set at less than 10% the relay closes and the
luminaires switch off.
Max
45 cm
Driver
12V AC
80-250V AC
50/60 Hz
Trans
.
Mains
80-250V AC
50/60 Hz
8
Configuring and installing an Alien 05 system
Warning
Do not draw more than 10 amps through the 05 Driver mains
relay. If the mains supply is under 200 volts and the number of
connected Alien 05’s is over 15, check that the combined
current draw of all transformers will not exceed 10 A.
R e m ot el y d i m m a b l e p o w e r - s u p p l y c on fi g u r a t i o n
Note:
This configuration does not apply for Alien 05 Eyeball models
as they draw their power via the transformer that is built into
the Halo Recessed fixture housing. These transformers are not
dimmable.
In this configuration, one or more dimmable transformers supply 12V power
to one or more Alien 05s, and are connected to the 0-10V analog output on
the 05 Driver. The transformer can be powered through the 10A mains relay
(if remote power on/off is required), or directly from the mains supply.
Mains
80-250V AC
50/60 Hz
Max
45 cm
Driver
Dim.
80-250V AC
50/60 Hz
12V AC
Trans
.
Analog 0-10V
Using the Oracle controller, or a DMX control device, it is possible to dim,
and power on and off the Alien 05s via the intensity channel.
Warning
Do not draw more than 10 amps through the 05 Driver mains
relay. If the mains supply is under 200 volts and the number of
connected Alien 05 luminaires is over 15, check that the
combined current draw of all transformers will not exceed 10 A.
Connecting transformers to a power supply
Supplying power through the 05 Driver to the transformers that power the
Alien 05 luminaires is optional and transformers may be connected directly
to the mains supply if there is no requirement for remote dimming or
power/on via the 05 Driver. Refer the documentation supplied with you
transformer for guidance.
In the cases that remote:
Configuring and installing an Alien 05 system
9
• Power on/off via the 05 Driver is required, transformers may be wired
through the 05 Driver’s mains output relay. The relay cuts power to the
transformer when the intensity is set to less than 10 percent. It supplies
power when the intensity is set to 10 percent or more.
• Dimming is required, a dimmable transformer may be connected through
the analog 0 - 10 V output on the 05 Driver. This output controls the dimmer
function only and does not provide power to illuminate the luminaires. This
function is not available for 05 Driver Eyeball models.
C on n e ct i n g t r a n s fo r m er s t o t h e 0 5 D r i v e r
To connect transformers to the 05 Driver, perform the following steps:
1 If the mains supply is under 200 volts and the number of connected Alien
05’s is over 15, verify that the combined current draw of all transformers will
not exceed 10 A.
2 Verify that the 05 Driver is isolated from AC power.
3 If wiring more than 1 transformer, connect the transformer leads to a
suitable power distribution strip or junction with a single lead to the 05
Driver. If the transformers are dimmable, similarly gather the control leads to
a parallel junction.
4 Remove top cover of the 05 Driver. Feed transformer power lead through
opening in the front panel labelled “Mains Output Relay”. If required, feed
the dimmer control lead through the opening labelled “0 - 10V Dimmer Out”.
Connect as shown on top cover.
5 Replace the cover.
6 Connect 12 V transformer output to lighting units. See Alien 05 user manual.
Warning:
The cable length between the transformer and the Alien 05/s
must not be more than 45 cm (17.7 inches).
Control network cabling
Alien 05s must be connected to a 05 Driver unit (directly, or indirectly via an
05 Repeater unit) that contains the intelligent control functions. The 05
Driver transmits commands to the Alien 05 luminaires via CAT5 network
cables (also available separately).
Each 05 Driver unit has six independent control channels, to each of which
an 05 Repeater, or up to four Alien 05s can be connected (in a daisy-chain).
Each 05 Driver channel can provide an individual program - with different
10
Configuring and installing an Alien 05 system
effects - to the Alien 05 luminaires connected to that channel. All the fixtures
on one channel will mimic each other in their behavior.
Up to eight 05 Repeaters can be daisy-chained to the 05 Driver via the
Channel link Out/In connectors, but note that this link is unamplified and
that the last fixture in this daisy chain should not be more than 40 cable
meters (130 feet) away from the 05 Driver.
If you connect 05 Repeaters to each or any one of the 6 amplified Output
(A-F) connectors on an 05 Driver (or another 05 Repeater), a theoretically
unlimited number of Alien 05 luminaires may be connected to an single
controlling 05 Driver.
Driver
Oracle
DMX control device
Alien 05 luminaires
Repea
ter
Repea
ter
Repea
ter
Warning:
Do not mix Alien 05 luminaries and 05 Repeaters on the same
Output link. Connect only Alien 05 luminaires, or only a 05
Configuring and installing an Alien 05 system
11
Repeater, to an individual connector. This applies to both the 05
Driver and the 05 Repeater.
Driver
Repea
ter
Note:
The maximum control network cable run between the an
amplified signal source (05 Driver or 05 Repeater) and the last
connected Alien 05 is 40 meters (131 ft.) Solid or stranded cable
may be used.
Laying control network cables
Lay network cables from as many of the 05 Driver’s, or 05 Repeater’s, six
RJ-45 output channel sockets as is necessary to the Alien 05 mounting
positions. Start with the locations closest to the 05 Driver or 05 Repeater.
If you are connecting multiple Alien 05s in daisy chains, run cables from the
first positions in the chain to the next ones. In this way you will connect the
first Alien 05 luminaire to the second Alien 05 luminaire, the second
luminaire to the third, and the third to the fourth. The connection order is not
important but keep the cable run from any single 05 Driver or 05 Repeater to
the last luminaire in its chain of connected luminaires to less than 40 meters
(131 ft.). The cable sockets on the 05 Drivers are identical: either one may
be used for input.
Connecting an Oracle control device
If you will be using the optional Oracle controller to program and playback
pre-recorded scenes, connect it to the 05 Driver using stranded cable.
1 Lead one end of the network cable over the Oracle’s base and plug it into
the RJ-45 socket on the back. (Do not lead the cable under the ring base.)
2 Lead the network cable to the 05 Driver and plug it into the bottom link
socket, labelled “In/Oracle”.
Note:
12
The cable run from the Oracle remote interface to the 05 Driver
must not exceed 40 meters (130 ft.).
Configuring and installing an Alien 05 system
Connecting a DMX control device
If you will be using an (optional) DMX controller to select scenes, connect it
using a DMX cable to the 05 Driver’s 3-pin XLR input socket. This socket is
compatible with the USITT DMX-512 (1990) standard for DMX data
connection.
R ec om m e n d ed c ab l e
A reliable data connection begins with the right cable. Standard microphone
cable cannot transmit DMX data reliably over long runs. For best results,
use cable specifically designed for RS-485 applications. Your Martin dealer
can supply high quality cable in various lengths.
C a b le a d a p t or s
The 05 Driver’s XLR data sockets are wired with pin 1 to ground, pin 2 to
signal - (cold), and pin 3 to signal + (hot). One or more adaptor cables may
be required to connect the 05 Driver to the controller and/or other lights
because many devices have 5-pin connectors and others may have
reversed signal polarity, that is, pin 2 hot and pin 3 cold.
5-pin to 3-pin
Adaptor
3-pin to 5-pin
Adaptor
3-pin to 3-pin
Phase-Reversing
Adaptor
Male
Female
Male
Female
Male
Female
1
2
3
4
5
1
2
3
1
2
3
1
2
3
4
5
1
2
3
1
2
3
P/N 11820005
P/N 11820004
P/N 11820006
Connecting the data link
1 Connect a data cable to the controller’s output. If controller has a 5-pin
output, you will need a 5-pin male to 3-pin female adaptor cable, available
separately.
2 Lead the data cable from the controller to the 05 Driver and plug it into the
Serial data link (DMX) In socket.
Configuring and installing an Alien 05 system
13
3 To connect additional 05 Drivers or other DMX
devices to the link, plug a DMX cable into the female
DMX Out socket of the fixture closest to the
controller and the input of the next fixture. If the
device has a 5-pin input, you will need a 3-pin male
to 5-pin female adaptor cable, available separately.
Continue connecting fixtures output to input. Up to 32
devices may be connected on a serial link.
Male
Termination Plug
Male XLR
1
2
3
120
4 Finally, terminate the link by inserting a male
P/N 91613017
termination plug into the data output of the last
fixture. A termination plug, which is simply an XLR
connector with a 120 ohm, 0.25 W resistor soldered across pins 2 and 3,
improves signal transmission.
5 See “DMX configuration” on page 21.
14
Configuring and installing an Alien 05 system
General operation
3
Control methods
The 05 Driver driver can be used to control lighting effects in connected
Alien 05s in any one of three ways:
1 Via the separately-orderable Oracle control interface which can be used to
program and playback pre-recorded scenes. See “Oracle control” on page
17.
2 Without an external interface, in stand-alone mode, where scenes can be
selected using DIP switches on the outside of 05 Driver. See “Stand-alone
control” on page 23.
3 Via an attached DMX device such as a DMX controller, or DMX recorder.
See “DMX configuration” on page 21.
LED indicators
There are a number of LED indicators on the top of the 05 Driver that
provide information about the status of operation.
Output failure LEDS
When illuminated, these red LEDs - for channels 1 to 6 - indicate that there
has been line failure, or a short within the 05 Driver, for that channel.
To test for a line failure, disconnect the Alien 05 fixtures on that channel
starting from the fixture at the end. Once a damaged cable is removed the
remaining fixtures should start to function normally. This indicates that a
replacement cable is probably needed.
If there is a short in the channel then return the 05 Driver to your Martin
dealer for service.
General operation
15
L i n k p ow er f ai lu r e
The Link power failure LED indicates that there has been a line failure in the
link from the Oracle remote control. Check and if necessary replace the
cable.
Info LEDS
Info 1
Info 1 blinks when software is being uploaded. See “Firmware updates” on
page 24.
Info 2 & 3
These blink during startup and reset, but when running in stand-alone
modes (using the DIP switches) or when DIP pins 1 & 2 are set on the 6 pin
DIP switch, these LEDs indicate the software version that is installed on
power up. The number of flashes in Info 2 indicates the digit to the left of the
decimal point and the number of flashes in Info 3 indicates the digit to the
right of the decimal point. For example, if the firmware version is 1.3, Info 2
flashes once and Info 3 flashes three times.
12 V and 5V LEDs
When lit, these green LEDs indicate that power is flowing normally to the
Alien 05 color wheel motors (12V through output channels 1-6) and within
the 05 Driver itself.
R el a y L E D
When lit, this green LED indicates that power is passing out of the mains
output relay to power the transformers that light the Alien 05s.
Receiving data LED
This green LED flickers when data is being received from a controlling.
When the Oracle is connected the flicker is quite faint, but is stronger when
a DMX controller is connected.
16
General operation
4
Oracle control
The Oracle control interface allows you to do the following:
•
•
•
•
•
•
Execute factory-installed programs
Select individual looks (scenes) for static projection
Program, save, and execute up to 16 sequences
Edit the welcome text
Read the Oracle and 05 Driver hardware and software version numbers
Reset the system
Important! Set pins 5 and 6 on the 6-pin DIP-switch to the OFF position to
enable Oracle control.
The Oracle control panel has 5 keys as shown below. In addition to menu
navigation, the “Ok”, “Back”, and “Function” keys have context-sensitive
functions that are displayed on the bottom line when they apply.
Ok
Back
Scroll down
Function
Scroll up
Playback
The Oracle enters playback mode on start-up.
Running a program or displaying a scene
1 Verify that pins 1, 2, 5, and 6 on the 6-pin DIP-switch are in the OFF position
(up).
Oracle control
17
2 Switch on power to the system and wait a few seconds while the system
starts up. If lamp power is wired through the system relay, the lamps will not
light until you select a program.
3 “SELECT PROGRAM” should be displayed at the top of the screen. Scroll
to a program with the ▲ and ▼ and down keys.
4 Press “Ok”. This brings you to the scene selection menu where you can
manually select and project any scene in the program using the ▲ and ▼
keys. “Start” and “Back” are displayed at the bottom of the screen: these are
the current functions of the top-left and top-middle keys.
5 Press “Start” to run the program. The program starts and the program
execution screen appears in the Oracle display. It shows the name of the
program, the number of the current scene, and remaining scene time. The
program loops continuously.
6 To stop execution, press “Stop”.
Programming
The 05 Driver’s memory stores up to 16 programs, or sequences. These
consist of up to 8 scenes that run in a continuous loop. Each scene can be
programmed with the following:
ne
e
Wa
it
ce
Sc e n
e3
S
d
Fa
Wait
1
• Either a global color (one that applies
to all channels) or unique colors for
each channel
• A global wait time
• A global fade time
• A global intensity (available if you are
using dimmable transformers in your
configuration)
d
Fa
e
de
Each scene has a dynamic part - the
Fa
Wait
fade - during which effects move to
the scene’s programmed positions,
and a static part - the wait - where the
effects in the scene are expressed. The total time it takes a scene to
execute is the sum of the fade and wait times.
2
ene
Sc
Creating or editing a program
Note: When key functions are not identified on screen, the functions are as
shown on page 17.
18
Oracle control
1 Press the middle key as required until “SELECT PROGRAM” is displayed
on the top line. Press and hold “Function” for approximately 3 seconds until
the display changes. Press Ok.
2 This brings you to the program selection menu. Scroll down to an available
program slot. Press Ok.
3 This brings you to the scene selection list. The list shows, from left to right,
each scene’s number, status, wait time, and fade time. Select a scene with
the ▲ and ▼ keys. Press Ok.
4 This brings you to the scene edit menu. The scene options are listed in
Table 1. To make a change, scroll to a parameter with the ▼ and ▲ keys,
press Ok, adjust the value with the ▼ and ▲ keys, and press Ok again. For
fade and wait times you press Ok after setting the minutes and after setting
the seconds.
5 Adjust all parameters as desired. When finished, press Back, or, to jump to
the next scene, press and hold Function.
6 Program additional scenes as desired. When finished, press Back until you
are prompted to save changes. There are 3 options; to:
• Save the changes with the current program name, press “Save”.
• Both save the changes and rename the program, press “Rename”.
• Exit without saving, Press “No”.
7 This brings you back to the top of the programming menu. Press “Back”
twice to return to the playback menu.
Parameter
Options
Notes
Scene No.
disabled, enabled
Select “enabled” to include the scene in the program.
Wait time
00:00 - 99:59
The wait is the period during which the scene does not
change. A wait time of 00:00 results in continuous
change. The time is expressed in minutes and
seconds.
Fade time
00:00 - 59:59
The fade is the period during which the scene changes
from the previous scene. A fade time of 00:00 results in
instant change; a fade time of 59:59 is imperceptible.
All Channel col.
1-9
The global color position for all channels. This
parameter automatically changes to N/A when a color
is selected for one of the channels. The standard color
positions are shown in Table 2.
Channel X col.
1-9
The color position for the individual channel. Unique
colors are overridden when a global color is selected.
Table 1: Scene Parameters
Oracle control
19
Parameter
Options
Notes
Intensity
0 - 100%
Full range dimming requires dimmable transformers
connected to the 0 - 10V dimmer output.
On/off switching of lamp power is available through the
mains output relay. It opens when intensity is 0% and
closes when it is 10% or more.
Table 1: Scene Parameters
Position
Filter
1
No filter - open position (a filter can be installed if required)
2
Color temperature correction (CTC) 5500-3400 K (warmer light)
3
Yellow 604
4
Red 305
5
Pink 312
6
CTC 3200-5600 K (colder light)
7
Blue 106
8
Blue 103
9
Green 201
Table 2: Standard Alien 05 Colors
20
Oracle control
5
DMX configuration
This section describes how to set-up the Alien 05 system with a DMX
controller. For further information on DMX operation, refer to your controller
manual. See also the DMX protocol on page 27.
Important! Set pins 5 and 6 on the 6-pin DIP-switch to the OFF position to
enable DMX control.
DMX modes
The 05 Driver has 3 DMX control options to suit your programming capacity
and preferences. To select the DMX mode, set pins 1 and 2 of the 6-pin
DIP-switch as shown in Table 3. Set pins 5 and 6 to OFF.
DMX channels
Mode 1
Mode 2
Mode 3
7
9
14
Intensity control N/A
Global
Individual channel
Individual channel
Individual channel
Color control
Individual channel
Speed control
N/A
Global
Global
DIP setting
Pin 1 off, pin 2 off
Pin 1 on, pin 2 off
Pin 1 off, pin 2 on
Table 3: DMX Mode Summary
DMX address
The 05 Driver requires from 7-14 DMX control channels. The DMX address,
also known as the start channel, is the first control channel used. It is a
logical address to which control instructions are sent. In this way a
controller, can send instructions to a fixture, or fixtures, at a particular
address. For example if the 05 Driver uses seven channels of control data, it
reads the data on the start channel (DMX address) and the next six
channels. If the DMX address is set to 100, the 05 Driver uses channels
100, 101, 102, 103, 104, 105, and 106.
DMX configuration
21
S e t t i n g t h e DMX ad dre ss
1 Select a DMX address for the fixture on your controller.
2 Locate the 10-pin DIP-switch on the front panel of the 05 Driver. Look up the
DIP-switch setting for the address in Table 5 on page 28. Set pins 1 through
9 to the ON (1) or OFF (0) position as listed in the table. Set pin 10 to the
OFF (0) position.
22
DMX configuration
Stand-alone control
6
This section describes how to operate the system without an external
interface.
Over view
The 05 Driver provides 2 stand-alone control modes. In mode 1, the color
wheel rotates between two color positions, then stops and waits at each end
position before reversing and scrolling back. Mode 2 is similar but the color
wheel stops and waits at each intermediate color position as well.
The stand-alone settings apply to all output channels; individual channel
control is not provided.
Set-up
Stand-alone options are set with the 05 Driver’s DIP-switches. The 10-pin
DIP switch allows you to select the following:
•
•
•
•
Start color position (1 - 8)
End color position (2 - 9)
Fade speed (very slow, slow, medium, fast)
Wait time (0, 10, 30, 120 seconds)
The mode is selected on the 6-pin DIP-switch. Note: DMX and Oracle
control are disabled when a stand-alone mode is selected.
O p er at i n g i n s t an d - alo ne mo de
1 Apply power to the system.
2 Select mode 1 or 2 on the 6-pin DIP-switch.
• To select mode 1, set pin 5 to ON and pin 6 to OFF.
• To select mode 2, set pin 5 to OFF and pin 6 to ON.
3 Select color and timing options with the 10-pin DIP-switch. See Table 6 on
page 29.
Stand-alone control
23
7
Service
This section describes service procedures that can be performed by the
user. Refer all service not described here to a qualified Martin technician.
Warning!
Disconnect the fixture from power before removing the cover.
Firmware updates
Firmware updates are released when features are added. The latest version
is available from the Support Area of the Martin Professional web site at
http://www.martin.dk.
The installed firmware version number is displayed by the LEDs Info 2 &
Info 3 on power up. The number of flashes in Info 2 indicates the digit to the
left of the decimal point and the number of flashes in Info 3 indicates the
digit to the right of the decimal point. For example, if the firmware version is
1.3, Info 2 flashes once and Info 3 flashes three times.
Firmware updates are installed by serial upload with either the MP-2 or
some LightJockey DMX interfaces: please refer to the MP-2 user manual or
the LightJockey's online help.
Updating firmware wit h an MP-2 Up loader
Pre-requisites
The following are required in order to install firmware using an MP-2.
• The 05 Driver update file, available for download from the User Support
Area of the Martin web site (http://www.martin.dk).
• The Martin Software Uploader program, version 4.0 or later, available for
download from the User Support Area of the Martin web site.
• A Martin MP-2 Uploader
• A Windows 95/98/ME/2000 PC, or a LightJockey
P r o ce d u r e
1 Connect a prepared MP-2 Uploader to the 05 Driver DMX input.
24
Service
2 Apply power to the 05 Driver and the MP-2.
3 Wait a few moments for the 05 Driver to reset.
4 Select Read Memory Card from the MP-2 main menu.
5 Use the buttons on the right to scroll through the card slots. Select the slot
that holds the desired version of 05 Driver firmware.
6 Select Update Software. Select Yes to confirm.
7 Select Update in DMX mode to start the upload. The MP-2 initializes all
connected 05 Drivers. Avoid interrupting the process: this will corrupt the
software.
Fuse replacement
To replace the fuse:
1 Disconnect the fixture from power.
2 Remove the fixture cover.
3 The fuse can be found on the printed circuit board. Remove the old fuse and
replace with a new 3.15 AT fuse.
4 Replace the fixture cover and apply power.
Service
25
8
Troubleshooting
Problem
Probable cause(s)
No response from fixture when No power to fixture.
power is applied.
Main fuse blown.
Alien 05s do not respond
correctly to 05 Driver unit
Remedy
Check power cables.
Check and replace fuse if
necessary.
05 Driver unit not connected.
Connect 05 Driver unit.
Bad data link connection.
Inspect cables and correct
poor connections and/or
broken cables.
Short in one of the output
Return the fixture to your
channels (indicated by one or Martin dealer for service.
more red output failure LEDs)
26
Alien 05s do not respond to
commands issued from an
Oracle control interface.
Line failure in the link from the Check and if necessary
Oracle remote control.
replace the cable between the
Oracle and the 05 Driver.
Everything lights but the
fixtures do not respond.
Incorrect setting on 6-pin DIP- Set all pins on 6-pin DIPswitch.
switch to the OFF position
(up). For DMX control, select
DMX mode (page 21). For
stand-alone control, select
mode 1 or 2 (page 23).
Troubleshooting
A
N/A
Ch. 1
Mode 3
Mode 2
Mode1
DMX protocol
Ch. 1 - 6
Value
0 - 255
0 - 19
19 - 38
38 - 57
57 - 76
76 - 95
95 - 114
114 - 133
133 - 152
Percent
Function
0 - 100
intensity
0 - 100%
0-8
8 -15
15 - 22
22 - 30
30 - 37
37 - 45
45 - 51
51 - 60
Color position
Stepless scroll
Color 1 -> Color 2
Color 2 -> Color 3
Color 3 -> Color 4
Color 4 -> Color 5
Color 5 -> Color 6
Color 6 -> Color 7
Color 7 -> Color 8
Color 8 -> Color 9
Ch. 1 - 6 Ch. 2 - 7 Ch. 7 - 12
153 - 163 60 - 64
164 - 174 64 - 68
175 - 185 69 - 73
186 - 196 73 - 77
197 - 207 77 - 81
208 - 218 82 - 86
219 - 229 86 - 90
230 - 240 90 - 94
241 - 255 95 - 100
N/A
Ch. 8
Ch. 13
Ch. 7
Ch. 9
Ch. 14
0-2
3 - 255
0-1
1 - 100
Stepped scroll
Color 9 (Green 201)
Color 8 (Blue 103)
Color 7 (Blue 106)
Color 6 (Cold CTC)
Color 5 (Pink 312)
Color 4 (Red 305)
Color 3 (Yellow 604)
Color 2 (Warm CTC)
Color 1 (Open white)
Color speed
Speed function off (tracking)
Color speed, fast to slow
Reset
0 - 250
0 - 98 Reserved
251 - 255 98 - 100 Reset system (hold 5 seconds)
Table 4: DMX Protocol
DMX protocol
27
DMX address
settings
DIP-Switch Setting
#1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0 = OFF
1 = ON
#2 #3 #4
0
0
0
0
0
0
1
0
0
1
0
0
0
1
0
0
1
0
1
1
0
1
1
0
0
0
1
0
0
1
1
0
1
1
0
1
0
1
1
0
1
1
1
1
1
1
1
1
0
0
0
0
0
0
1
0
0
1
0
0
0
1
0
0
1
0
1
1
0
1
1
0
0
0
1
0
0
1
1
0
1
1
0
1
0
1
1
0
1
1
1
1
1
1
1
1
#5
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
#9
#8
#7
#6
B
0
0
0
0
0
0
0
1
0
0
1
0
0
0
1
1
0
1
0
0
0
1
0
1
0
1
1
0
0
1
1
1
1
0
0
0
1
0
0
1
1
0
1
0
1
0
1
1
1
1
0
0
1
1
0
1
1
1
1
0
1
1
1
1
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
365
366
367
368
369
370
371
372
373
374
375
376
377
378
379
380
381
382
383
384
385
386
387
388
389
390
391
392
393
394
395
396
397
398
399
400
401
402
403
404
405
406
407
408
409
410
411
412
413
414
415
416
417
418
419
420
421
422
423
424
425
426
427
428
429
430
431
432
433
434
435
436
437
438
439
440
441
442
443
444
445
446
447
448
449
450
451
452
453
454
455
456
457
458
459
460
461
462
463
464
465
466
467
468
469
470
471
472
473
474
475
476
477
478
479
480
481
482
483
484
485
486
487
488
489
490
491
492
493
494
495
496
497
498
499
500
501
502
503
504
505
506
507
508
509
510
511
Table 5: DMX Address DIP-Switch Settings
28
DMX address settings
C
Stand-alone settings
Pin setting (0 = OFF, 1 = ON)
Effect
Start color
End color
Fade speed
Wait time
Value
1
2
3
1. White
0
0
0
4
5
6
2. Warm CTC
0
0
0
3. Yellow 604
1
0
0
4. Red 305
0
1
0
5. Pink 312
1
1
0
6. Cold CTC
0
0
1
7. Blue 106
1
0
1
8. Blue 103
0
1
1
9. Green 201
1
1
1
2. Warm CTC
1
0
0
3. Yellow 604
0
1
0
4. Red 305
1
1
0
5. Pink 312
0
0
1
6. Cold CTC
1
0
1
7. Blue 106
0
1
1
8. Blue 103
1
1
1
7
8
9
Very slow
0
0
Slow
1
0
Medium
0
1
Fast
1
1
10
0 seconds
0
0
10 seconds
0
1
30 seconds
1
0
120 seconds
1
1
Table 6: Stand-Alone Settings
Stand-alone settings
29
6-pin DIP-switch
settings
D
Pin setting (0 = OFF, 1 = ON)
Mode or Function
1
2
3
4
6
0
0
0
0
DMX mode 1
0
0
0
0
DMX mode 2
1
0
0
0
0
0
DMX mode 3
0
1
Reset & hold
1
1
Stand-alone mode 1
Stand-alone mode 2
Note: Overrides DMX and
Oracle control!
Table 7: 6-pin DIP-Switch Settings
30
5
Oracle control
6-pin DIP-switch settings
1
0
0
1
Specifications
E
Physical
Size (L X W x H) . . . . . . . . . . . . . . . . . . . . . .375 x 104 x 43 mm (14.8 x 4.1 x 1.7 in.)
Weight. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.8 kg (1.8 lbs.)
Co nt r o l
Remote interfaces. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DMX-512, Martin Oracle
Onboard option and address setting. . . . . . . . . . . . . . . . . . . . . . . . . . 2 DIP-switches
Data input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CAT5 network cable (not supplied)
Data output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CAT5 network cable (not supplied)
T h e r m al
Maximum ambient temperature (Ta). . . . . . . . . . . . . . . . . . . . . . . . . . . 40° C (104° F)
AC S u ppl y
05 Driver unit power supply . . . . . . . . . . . . . . . . Auto-ranging - 80 - 250 V, 50/60 Hz
Power consumption (excluding lamp transformers) . . . . . . . . . . . . . . . . . . . . . . 50 W
Current consumption (excluding lamp transformers) . 0.4 A @ 120 V, 0.2 A @ 230 V
Fuse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.15 AT
Co ns t r u ct i o n
Housing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .sheet aluminum
Finish . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . electrostatic powder coating
Color . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . black (RAL 9005)
Design standards
EU safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . EN 60598-2-2
Control & Programming
Control options . . . . . . . . . . . . . . . . . . . . . DMX-512, stand-alone using DIP switches
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .dedicated operator panel - Oracle
Data input . . . . . . CAT5 network cable (not supplied) - maximum length 10 m (33 ft)
Data output . . . . . CAT5 network cable (not supplied) - maximum length 10 m (33 ft)
D y n am i c ef f ec t s
8 color filters plus open
Speed control
Lamp on and off
Intensity
Specifications
31
Ordering information
05 Driver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .P/N 90722010
05 Repeater . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .P/N 90722020
Oracle controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .P/N 90722000
Alien 05 Stem Mount, 12V, 50 W. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .P/N 90340200
600 mm Arm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P/N 91611068
150 mm Arm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P/N 91611067
Base (230V/12V-75W) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .P/N 90722030
Base (120V/12V-75W) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .P/N 90722040
Alien 05 Eyeball, 12V, 50 W . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .P/N 90340100
Halo brand, recessed low-volt non-IC fixture housing. . Cooper Lighting item number
H7LVT
Alien 05 Recessed, 12V, 50 W . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .P/N 90340000
Dimmable transformer - 230 V @ 50/60 Hz/35-105 W @ 12 V . . . . . P/N 91611054
Accessories
CAT5 network cables - 2 m (6.5 ft) x 50 pieces. . . . . . . . . . . . . . . . . . . P/N 91611044
CAT5 network cables - 5 m (16.4 ft) x 30 pieces. . . . . . . . . . . . . . . . . . P/N 91611045
CAT5 network cables - 10 m (32.8 ft) x 15 pieces. . . . . . . . . . . . . . . . . P/N 91611045
32
Specifications
www.martin-architectural.com • Olof Palmes Allé 18 • 8200 Aarhus N • Denmark
Tel: +45 8740 0000 • Fax +45 8740 0010