advertisement
▼
Scroll to page 2
of 8
LIMITED WARRANTY All equipment which is sold under ANVIL trademark and used for commercial purposes is warranted against defects in materials and workmanship. The warranty runs for two years from the date of original installation and is for the benefit of the original purchaser only. All other Warranties ,expressed or implied , statutory or otherwise, including without limitations any implied Warranty of Merchantability or fitness for purpose are excluded .The Seller shall in no event be liable for direct,indirect or consequential damages in connection with ANVIL commercial products. CREPE MACHINE The Sellers obligation under this Warranty is limited to the repair of defects without charge. Defective units must be taken or shipped,transportation charges prepaid,to ANVIL. This Warranty is not effective if damage occurs because of accident,carelessness,improper installation,lack of proper set-up,supervision when required or if the equipment is installed or operated in any manner contrary to the installation and operating instructions. In these cases,repairs will be made at a reasonable cost. Work performed by unauthorized personnel or unauthorized service agencies using non Anvil spares voids this Warranty. NB: REGISTER ON-LINE TODAY Register your warranty on-line now at www.anvilworld.com NO WEB ACCESS If you do not have access to the Web. Kindly register by completing the warranty registration form and fax it to the ANVIL office in the country of purchase. Failure to do so will invalidate your warranty. 4-INS-PMA1011R01 INSTALLATION OPERATION AND CARE OF SINGLE PLATE CREPE MACHINE MODEL: PMA1011 R00 1 10 UNPACKING Unpack the product and check for any damage incurred during transit. This should be reported to the responsible carrier, railway or postal authority, and a request for a damage report should be made. THESE INSTRUCTIONS GUARANTEE OUR FULL PROTECTING AGAINST THE FORM FOR FILING BY THE CARRIER. MUST BE FOLLOWED FOR US TO SUPPORT OF YOUR CLAIM FOR LOSS FROM CONCEALED DAMAGE. SUCH A CLAIM WILL BE PROVIDED GENERAL INSTALLATION AND OPERATION INSTRUCTIONS 1. The top working surface has a Teflon coating. Before using the unit for the first time, it should be heated for +/- 20 minutes to allow the elements to burn in. 2. The unit is provided with a wooden scraper. It is essential that this is used on the heated top to prevent damage to the Teflon coating. Steel scrapers will scratch the surface. 3. Set the unit to the desired temperature. The thermostat will maintain this temperature by switching the elements on and off. 4. Anvil crepe machines are equipped with one pilot light which will remain illuminated when the unit is switched on. 5. The unit is provided with a lower warming drawer. 9 2 WARNING Burn Hazard. Do not touch hot food,liquid or heating surfaces while equipment is heating or operating Hot surfaces and food can burn skin. Allow the hot surfaces to cool before handling CLEANING 1. Always ensure that the unit is disconnected from the main power supply before cleaning. 2. This unit should not be cleaned with a water jet or immersed in water. Use only a damp cloth or sponge dipped in soapy water. 3. Wipe off the unit with a dry cloth and wait at least a half an hour before re-connecting to the main power outlet. CLEAN THE STAINLESS STEEL PARTS WITH WATER AND SOAP. AVOID THE USE OF DETERGENTS CONTAINING ABRASIVE SUBSTANCES. ALWAYS RINSE WELL AND DRY CAREFULLY AFTER CLEANING. DO NOT USE PRODUCTS CONTAINING AGGRESSIVE CHEMICALS, ACIDS OR PRODUCTS WITH CHLORINE TO CLEAN THE STAINLESS STEEL EVEN IF DILUTED 3 MODEL: SINGLE PLATE CREPE MACHINE MODEL:SINGLE PLATE CREPE MACHINE MODELCODE CODE :PMA : PMA1001 1011 R01 MODEL WARNING Electric Shock Hazard. Keep water and other liquids from entering the inside of the equipment. Liquid inside the equipment could cause an electrical shock Do not spray water or cleaning products. Liquid could contact the electrical components and cause a short circuit or an electrical shock. Do not use equipment if power cord is damaged or has been modified SAFETY READ ALL INSTRUCTIONS BEFORE USE. FAILURE TO FOLLOW THESE PRECAUTIONS COULD RESULT IN INJURY TO YOURSELF AND OTHERS 1. When this appliance is to be positioned in close proximity to a wall, partitions, kitchen furniture, decorative finishes, etc.it is recommended that they be made of non-combustible material. If not, they shall be clad with a suitable non-combustible heat insulating material, and the closest attention be paid to fire prevention regulations. 2. Use the multifunction warmer on an individual 15A mains outlet only. DO NOT OVERLOAD THE CIRCUIT. 3. Ensure that the equipment and the power supply cord does not come into contact with hot surfaces. 4. Supervision is necessary when the appliance is used in close proximity to children. 5. If the supply cord is damaged, it must be replaced with a new cord assembly available from the suppliers agent. The cord shall be an oil resistant sheathed flexible cable not lighter than ordinary polychloroprene or equivalent synthetic elastomer - sheathed cord (code designation 60245 IEC 57) 6. Use only earthed outlets matching the serial plate voltage. 7. Have equipment installed by a qualified personnel in accordance with local codes and ordinances. 8. Use equipment in a flat level position. 9. Do not operate unattended 10. The equipment may be hot, even though the pilot light is not on. 11. Do not operate if equipment has been damaged or is malfunctioning in any way. 12. These units are designed to run only on alternating current (A.C.) DO NOT CONNECT TO DIRECT CURRENT (D.C) Part No. Description 1 CAST IRON COOKING PLATE TEFLON COATED 2 ELEMENT 3000W 230V 12MM RED HEAT ELEMENT 3 ELEMENT COVER PLATE 4 CERAMIC CONNECTOR BLOCK 5 OUTER ENCLOSURE 6 THERMOSTAT 50-300C 7 CONTROL PANEL FACIA 8 CONTROL PANEL INSERT 9 CONTROL PILOT LIGHT 10 CONTROL KNOB 11 BEZEL 12 ANVIL AXIS LOGO 13 FOOT 14 BOTTOM COVER 15 CABLE GLAND 16 POWER CORD 8 7 EXPLODED DIAGRAM SINGLE PLATE CREPE MACHINE PMA1011 R00 4 POSITIONING DIAGRAM SINGLE PLATE CREPE MACHINE PMA1011 R00 10 7 9 8 6 11 4 448 5 3 2 513 1 12 13 15 16 14 CREPE MACHINE MODEL CODE: PMA1001 R01 257 5 ELECTRICAL CONNECTION INFORMATION MODEL DESCRIPTION VOLTS V/Hz POWER WATTS PMA1011 SINGLE PLATE CREPE MACHINE 230 /50hz 3000 6 WIRING DIAGRAM MODEL CODE: PMA1011 R00 MODEL: SINGLE PLATE CREPE MACHINE LEGEND DESCRIPTION PART NUMBER B1 CONTROL THERMOSTAT 1-EGO-150 E1 ELEMENT 3000W/230V 5-3000W-PMA1001 H1 CONTROL PILOT LIGHT 1-PL-GP IT IS ESSENTIAL TO MAKE SURE THAT THE INCOMING VOLTAGE IS THE SAME AS THE RATED VOLTAGE OF THE OF THE UNIT AS FOUND ON THE SERIAL PLATE. THE SERIAL PLATE IS LOCATED AT THE REAR OF THE UNIT ADJACENT TO THE INCOMING CABLE ENTRY. 230V 230V L N E B1 E1 H1
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project