YORK PCE4 Technical Guide

YORK PCE4 Technical Guide

TECHNICAL GUIDE

SINGLE PACKAGE AIR CONDITIONER / ELECTRIC HEAT 14 SEER – R-410A – 460V - 3 PHASE 3 THRU 5 NOMINAL TONS

MODELS: PCE4*36 THRU 60 Due to continuous product improvement, specifications are subject to change without notice.

Visit us on the web at

www.upgnet.com and www.york.com

Additional rating information can be found at:

www.ahridirectory.org

WARRANTY SUMMARY*

Standard 1-Year limited parts warranty.

Standard 5-Years limited compressor warranty.

See limited warranty certificate in User’s Information Manual for details.

5564252-YTG-A-1018

DESCRIPTION

These packaged cooling/heating air conditioners are designed for outdoor installation. Only utility and duct connections are required at the point of installation.

• • • • • • • •

FEATURES

Operating Efficiency -

All PCE4 air conditioner models are rated at 14.0 SEER and 11.0 EER for cooling operation.

On Site Flexibility -

All model sizes use a compact design cabinet in one of two footprints. This provides installer flexi bility for placing the proper capacity unit on curbs or pads with the smallest footprint after the internal load has been determined. Field convertible duct connections from side shot to down shot allows the installer to have greater flexibil ity with less inventory.

Lower Installation Cost -

Installation time and costs are reduced by easy power and control wiring connections. The small base dimension means less space is required on the ground or roof. All units are completely wired, charged with R-410A and tested prior to shipment. Test stations using a state-of-the-art computerized process system are used to insure product quality. Refrigerant charge and component part numbers are verified via computers during assembly.

Vital run test statistics such as system pressure, motor cur rents, air velocity and temperature, unit vibration, and gas system safeties are monitored and recorded by the system to insure unit performance. Equal size side supply and return duct connections allow easy connection of ducts to match low crawl spaces without transition pieces.

Utility Connections Made Easy -

Electric utility access pro vided through the bottom or the side of the unit. Utility con nections can be made quickly and with a minimum amount of field labor. A field supplied and field installed electrical dis connect switch must be installed.

Convertible Airflow Design -

The bottom duct openings are covered when they leave the factory, ready to be used for a side supply/side return application. If a bottom supply/bottom return application is desired, simply remove the two panels from the bottom of the unit and place them in the side supply/ side return duct openings. No panel cutting is required and no accessory panel is necessary. Convertible airflow design allows maximum field flexibility and minimum inventory.

Condensate Pan -

A corrosion-resistant, long-lasting, water tight pan is positioned below the evaporator coil to collect and drain all condensate, preventing build-up of stagnant condensate. The condensate pan conforms to ASHRAE 62 89 standards (Ventilation for Acceptable Indoor Air Quality).

Condensate Drain -

The 3/4 inch NPT female connection is rigidly mounted to assure proper fit and leak tight seal.

Durable Finish -

The cabinet is made of G90 galvanized steel with a powder paint coating for appearance and protec tion. The pre-treated galvanized steel provides a better paint to-steel bond, which resists corrosion and rust creep. Pow der paint finish ensures less fading when exposed to sun light, and provides superior corrosion resistance (1000 hour salt spray tested).

Continued on next page.

FOR DISTRIBUTION USE ONLY - NOT TO BE USED AT POINT OF RETAIL SALE

5564252-YTG-A-1018 • • • • • • •

Full Perimeter Base Rails -

The easily removable base rails provide a solid foundation for the entire unit and protects the unit during shipment. The rails provide fork lift access from all sides, and rigging holes are also provided so that an over head crane can be used to place the units on a roof. On applications where the unit is placed on a pad, the base will keep the unit off the pad to deter corrosion. On applications where height is limited, the base rails may be removed by removing 2 screws in each corner.

Attractive Appearance -

A single-piece top cover containing a top-discharge condenser fan arrangement requires less square footage on installation and provides a wider variety of installations. The one-piece design adds greater water integ rity. Rounded corners with water drip edges add to the attrac tive appearance.

Top Discharge -

The top-discharge outdoor fan does not disrupt neighboring areas or dry out vegetation surrounding the unit. The warm air from the top mounted fan is blown up and away from the structure and any landscaping.

Outdoor Coil Grille -

All models utilize a stamped slotted design which provides superior impact protection against small objects during transit and after installation.

Low Operating Sound Level -

The upward air flow carries the normal operating noise up and away from the living area.

The rigid top panel effectively isolates noise. Isolator mounted compressor and the rippled fins of the outdoor coil muffle the normal fan motor and compressor operating sounds. The unique formed base pan also aids in sound attenuation with its structural design.

Fan System -

All models operate over a wide range of design conditions with a standard ECM indoor fan motor.

These units easily match all types of applications and pro vide greater on-site flexibility to match comfort requirements.

The cooling speed is factory-set and can be field-adjusted to a second speed. The heating speed is factory set to maintain mid point rise at the units heating input, but can be field adjusted. This allows maximum comfort conditions.

Simple Control Circuit -

Field thermostat wiring connects to color coded wire leads using twist on wire connections. Cool ing controls use contactor and relays for simple application and troubleshooting. Mate-n-lock plug connectors are used.

The electrical control box is not located in the compressor compartment. The controls are mounted to allow the sepa rate access panel to be removed for trouble shooting and maintenance without affecting the normal system operating pressures. All wiring internal to the unit is color/number coded.

• • • • • • •

Protected Compressor -

The compressor is internally pro tected against high pressure and temperature. This is accomplished by the simultaneous operation of high pres sure relief valve and a temperature sensor which protect the compressor if undesirable operating conditions occur.

Pressure Switches -

A high pressure switch is standard in all units. It is an automatic reset switch. When discharge pressure reaches 650 psi, the compressor will de-energize until pressure reaches 450 psi.

Exclusive Coil Design -

Grooved copper tubes and enhanced aluminum fin construction improves heat transfer for maximum efficiency and durability for long-lasting durabil ity and efficient operation. Indoor coils will use tin-coated copper tubing with aluminum fins for effective heat transfer.

Electric Heat -

All electric heat models use 6HK electric heat, which are available in 460V/3/60 10kW to 25kW.

Low Maintenance -

Long life, permanently lubricated con denser and evaporator fan motor bearings need no annual maintenance, adding greater reliability to the unit. Slide-out blower assembly and evaporator coil assembly can be easily removed for cleaning.

Easy Service Access -

Individual access panels are pro vided in access to all major components - compressors, evaporator coils, blower, controls/electric heat kits, filters, etc. that makes servicing easy. Removing these panels allow easy removal of the components such as the blower assem bly for maintenance and ease of troubleshooting.

Replacement Parts -

The installer requires no special train ing to replace any of the components of these units and the number of new components have been reduced to minimize the inventory of unique parts.

• Filter Frame Kit -

All 3 phase PCE units include a filter frame kit, which is shipped inside the unit from production.

Field installation is required.

Filters -

All 3 phase PCE units include an applicable number of 1" washable filters, which are shipped inside the unit from production. Field installation is required. Two filters are required for A base units. Three filters are required for B base units.

2 Johnson Controls Unitary Products

5564252-YTG-A-1018

NOMENCLATURE

PCE 1 4 2 1. Model Family

PCE - packaged A/C with electric heat, PHE - packaged with electric heat, PCG - packaged A/C with gas heat, PHG - packaged heat pump with gas heat.

2. Nominal Cooling Efficienc

y 4 = 14 SEER, 6 = 16 SEER, etc.

A 3 36 4 3 6 6. Voltage-Phase-Frequency 1 8 5. Gas Heating Input BTU/Hr x 1000

050 = 50,000 BTU/Hr. input, blank = electric heat 2 = 208/230-1-60, 3=208/230-3-60, 4 = 460-3-60

3. Cabinet Size

A = small 35 x 51, B = large 45 x 51

7. NOx Approval

X = low-NOx, blank = not low-NOx

8. Generation Level

1 = first generation.

2 = second generation etc

4. Nominal Air Conditioning Cooling Capacity BTUx1000

24 = 24,000 BTU, etc.

9. Revision Level

A = original release, B = second release

Examples:

PHE4B4221A is a packaged heat pump, 14 SEER, 3-1/2 ton, large cabinet, 230 volt, 1-phase model, (first generation, first release).

A 9

COMPONENT LOCATION

OUTDOOR FAN MOTOR OUTDOOR FAN OUTDOOR COIL (Behind Panel) COIL GUARD PANEL TXV COMPRESSOR INDOOR COIL REMOVABLE BASE RAILS

UNIT LIMITATIONS

Model

PCE4A3642 PCE4B4842 PCE4B6042

Unit Voltage

460-3-60 Johnson Controls Unitary Products CONTACTOR CAPACITOR TRANSFORMER BLOWER MOTOR OPTIONAL ELECTRIC HEAT KIT INDOOR BLOWER A0411-001

Min Unit Limitations Applied Voltage Max

432 504

Outdoor DB Temp Max (°F)

125 3

5564252-YTG-A-1018 • • • • • •

ACCESSORIES

Economizer for Downflow Applications (S1-2EE04710024, S1-2EE04710124) -

Modulating inte grated economizer provides simultaneous operation between mechanical cooling and economizer operation.

Independent blade design insures proper control and less than 1% leak rate. Includes hood and mesh bird screen filter integrated into the hood, dry bulb sensor, and barometric relief damper . Separate field accessories of single/dual enthalpy kits are also available.

Economizer for Horizontal Applications (S1-2EE04710224, S1-2EE04710324) -

Modulating inte grated economizer provides simultaneous operation between the mechanical cooling and economizer operation.

Independent blade design insures proper control and less than 1% leak rate. Includes hood and mesh bird screen filter integrated into hood and dry bulb sensor. Separate field accessories of single enthalpy and dual enthalpy are avail able.

• Barometric Relief Hood (S1-1RD0501)

- Used in conjunc tion with a horizontal economizer, the Barometric Relief Hood helps to equalize the building pressure that is caused by the fresh air that is introduced through the economizer fresh air hood.

Single/Dual Enthalpy Sensor (S1-HE-6863-0N00WS) -

Sensor replaces supply air temperature dry bulb sensor standard in economizer kit. Provides improved economizer operation by sensing the dry bulb temperature of indoor sup ply air plus the enthalpy content of the outdoor air.

• •

Duct/Unit Mount CO2 Kit (S1-2AQ04700924) -

Sensor kit detects CO2 levels automatically and overrides the econo mizer when CO2 levels rise above the preset limits.

Wall Mount CO2 Kit (S1-2AQ04701024) -

Sensor kit detects CO2 levels automatically and overrides the econo mizer when CO2 levels rise above the preset limits.

• Supply Air Temperature Sensor Kit (S1-TE-63616E-2D) -

Outdoor supply air temperature sensor kit used with econo mizers.

Filter/Frame Kit (Kit Provided) (S1-1FF0602, S1-1FF0601) -

Kit contains the necessary hardware to field install return air filters into the base unit.

The filter rack is suitable for either 1" or 2" filters.

Filter (S1-02647812000) -

Washable 1” filter. Two filters are required for A base units. Three filters are required for B base units. Washable filters are included inside shipped units for field installation.

Motorized Fresh Air Damper (S1-2MD04705224, S1-2MD04705124) -

Designed for duct mounted side supply/return and unit mounted down supply/ return applications. Damper capable of providing 0% through 50% of outdoor air (field supplied). Closes on power loss, includes hood and screen assembly.

Rectangle to Round (Horizontal) Adapter (S1-1AK0110, S1-1AK0111) -

Kit includes one supply and one return air rectangle to round duct adapter. Adapters are preformed and designed to fit over current horizontal duct openings on the base unit. Transition is from rectangle to 12" round for the 1AK0110 kit and from rectangle to 14" round for the 1AK0111 kit.

• • • • • • • •

Rectangle to Round (Downflow) Adapter (S1-1AK0108, S1-1AK0109) -

Kit includes one supply and one return air rectangle to round duct adapter. Adapters are preformed and designed to fit into current downflow duct openings on the roof curb. Transition is from rectangle to 16" round for the 1AK0108 kit and from rectangle to 18" round for the 1AK0109 kit.

Roof Curbs (S1-1RC0503, S1-1RC0501) -

NRCA approved curbs provide proper fit to base unit for rooftop installations.

Curbs are designed to be assembled through hinge pins in each corner. Kit also provides seal strip to assure an air tight seal. These are 8 inch high roof curbs.

Roof Curbs (S1-1RC0504, S1-1RC0502) -

NRCA approved curbs provide proper fit to base unit for rooftop installations.

Curbs are designed for assembly through hinge pins in each corner. Kit also provides seal strip to assure air tight seal.

These are 14 inch high roof curbs.

Transition Curb Kits (S1-1TC01*) -

Adapter kits to allow field use of pre-existing installed roof curbs to match PCE4 footprint to Affinity roof curbs, Carrier, Trane, or Goodman curb footprints. Curb adapters are optional for current gener ation Carrier replacements but are recommended for previ ous generation applications. Refer to the PCE4 price pages for more details.

Manual Outdoor Damper (S1-1FA0502, S1-1FA0501) -

Provides 0% through 50% outdoor air capability (field adjust able). Designed for duct mounted side supply/return applica tions and unit mounted down supply/return applications.

Includes hood and screen assembly.

Loss of Charge Switch (S1-2LC00024) -

Kit provides Loss of Charge Switch and wiring to provide safe shutdown of compressor.

Low Ambient Kit (S1-2LA04701024) -

Kit provides neces sary hardware to convert unit to operate in cooling cycle down to 0º F. Standard unit operation 45º F.

Base Rail Hole Cover Kit (S1-1HC0101) -

Kit provides nec essary hardware to close off openings in base rails to block off openings, i.e. prevent animal entrance.

• •

Single-Point Wiring Kits (S1-2SPWK031 through 037) -

Kit provides terminal block, fuse blocks and wiring to allow units with electric heat to be connected to a single source of incoming power.

Thermostat -

Compatible thermostat controls are available through accessory sourcing. For optimum performance, these outdoor units are fully compatible with the York Hx™ Touchscreen Thermostat available through Source1. For more information, see the thermostat section of the Product Equipment Catalog.

Wall Thermostat -

The units are designed to operate with standard, 24-volt electronic non power stealing and electro mechanical thermostats. All units can operate with single stage heat/single stage cool thermostats - with or without the economizer.

*

For additional kit numbers refer to the price pages.

4 Johnson Controls Unitary Products

GUIDE SPECIFICATIONS

GENERAL

Units shall be manufactured by Unitary Products in an ISO 9001 certified facility. These packaged cooling and heating air conditioners are designed for outdoor installation. Only utility and duct connections are required at the point of installation. Air conditioning units provide electric cooling and heating with field installed electric heat kits from 10 kW to 25 kW for heating operation.

DESCRIPTION

Units shall be factory-assembled, single packaged, air conditioners with electric cooling/electric heating units, designed for outdoor installation. They shall have built in, equal size, field convertible duct connections for supply/return or horizontal supply/return. The units shall be factory wired, piped, charged with R-410A refrigerant and factory tested prior to shipment. All models shall be rated in accordance with DOE and AHRI test procedures for both heating and cooling operation. Units shall be CSA listed to the UL 1995/CAN/CSA No. 236-M90 standards.

• •

Operating Efficiency -

All models shall be rated at a mini mum of 14.0 SEER and 11.0 EER for cooling and heating operation rated in accordance with DOE requirements.

Low Operating Sound Level -

The upward air flow carries the normal operating noise up and away from the living area.

The rigid top panel effectively isolates noise. Isolator mounted compressor and the rippled fins of the condenser coil muffle the normal fan motor and compressor operating sounds. The unique formed base pan also aids in sound attenuation with its structural design. Sound ratings as tested under AHRI test procedures shall be less than 77 dbA for all models.

UNIT CABINET

Unit cabinet shall be a single piece design, with drip edges and no-seam corners to provide optimum water integrity. Unit shall have a rigidly mounted condenser coil guard to provide protection from objects and personnel after installation. Indoor blower section shall be insulated with foil-faced or foam insulation, fastened to prevent insulation from entering the air stream. Cabinet panels shall be separate, easily removable for servicing and maintenance. Unit shall be built on a formed, design base pan, with embossments at critical points to add strength and rigidity and to aid in minimizing sound. Full perimeter base rails shall be provided to assure reliable transit of equipment, overhead rigging, for truck access and proper sealing on roof curb applications. Base rails shall be easily removable, when required to lower unit height. Filters shall be field installed, furnished and be accessible through a removable access door, sealed airtight. Units vertical discharge and return duct configuration shall be designed to fit between standard 24” O.C. beams without modification to building structure, duct work and base unit.

Durable Finish -

The cabinet shall be is made of G90 galva nized steel with a powder paint coating for appearance and protection. The pre-treated galvanized steel shall provide a better paint-to-steel bond, which resists corrosion and rust creep. Powder paint finish shall provide superior corrosion resistance (1000 hour salt spray tested).

5564252-YTG-A-1018 • • • • • • • • •

On Site Flexibility -

All model sizes shall use a compact design cabinet in one of two footprints. This provides installer flexibility for placing the proper capacity unit on curbs or pads with the smallest footprint after the internal load has been determined. Field convertible duct connections from side shot to down shot allows the installer to have greater flexibil ity with less inventory.

Attractive Appearance -

A single-piece top cover containing a top-discharge condenser fan arrangement shall be used which requires less square footage on installation and pro vides a wider variety of installations. The one-piece design adds greater water integrity. Rounded corners with water drip edges add to the attractive appearance and prevent water penetration.

Convertible Airflow Design -

The bottom duct openings are covered when they leave the factory, ready to be used for a side supply/side return application. If a bottom supply/bottom return application is desired, simply remove the two panels from the bottom of the unit and place them in the side supply/ side return duct openings. No panel cutting is required and no accessory panel is necessary. Convertible airflow design allows maximum field flexibility and minimum inventory.

Utility Connections Made Easy -

Electric utility access shall be provided through the bottom or the side of the unit. Utility connections should be made quickly and with a minimum amount of field labor. A field supplied and field installed elec trical disconnect switch must be installed.

Easy Service Access -

Individual access panels are pro vided in access to all major components - compressors, indoor coils, blower, controls/electric heat kits, filters, etc.

that makes servicing easy. Removing these panels allow easy removal of the components such as the blower assem bly for maintenance and ease of troubleshooting.

Top Discharge -

The top-discharge outdoor fan does not disrupt neighboring areas or dry out vegetation surrounding the unit. The warm air from the top mounted fan is blown up and away from the structure and any landscaping.

Outdoor Coil Grille -

All models utilize a stamped slotted design which provides superior impact protection against small objects during transit and after installation.

Indoor Blower Assembly -

Fan shall be direct drive design.

Fan wheel shall be double-inlet type with forward-curved blades, dynamically balanced to operate smoothly through out the entire range of operation. Airflow design shall be con stant air volume. Bearings shall be sealed and permanently lubricated for longer life and no maintenance. Fan assembly shall be a slide-out design for easy removal and cleaning.

Indoor blower motors shall be equipped with a standard high efficiency brushless DC motor (constant torque) also known as a standard ECM motor.

Outdoor Fan Assembly -

The outdoor fan shall be of the direct-driven propeller type, discharge air vertically, have alu minum blades riveted to corrosion resistant steel spider bracket and shall be statically balanced for smooth opera tion. The outdoor fan motor shall be totally enclosed with per manently lubricated bearings and internally protected against overload conditions.

Johnson Controls Unitary Products 5

5564252-YTG-A-1018

REFRIGERANT COMPONENTS

Protected Compressor -

The compressor shall be a fully hermetic type, direct drive compressor, that is internally pro tected against high pressure and temperature. This is accomplished by the simultaneous operation of high pres sure relief valve and a temperature sensor which protect the compressor if undesirable operating conditions occur. The hermetic motor shall be suction gas cooled and have a volt age range of +/- 10% of the unit nameplate voltage. Com pressors shall have internal isolation and sound muffling to minimize vibration and noise, and be externally isolated on a dedicated, independent mounting.

• • •

Indoor Coils -

Indoor coils shall be of the direct expansion, draw through design and have aluminum plate fins mechani cally bonded to seamless internally enhanced tin-coated copper tubes with all joints brazed.

Condensate Pan -

A corrosion-resistant, long-lasting, water tight pan is positioned below the indoor coil to collect and drain all condensate, preventing build-up of stagnant con densate. The condensate pan conforms to ASHRAE 62-89 standards (Ventilation for Acceptable Indoor Air Quality).

Condensate Drain -

The 3/4 inch NPT female connection is rigidly mounted to assure proper fit and leak tight seal.

Outdoor Coils -

Outdoor coils shall have aluminum plate fins mechanically bonded to seamless internally enhanced copper tubes with all joints brazed, and be a draw through design.

Refrigerant Circuit and Refrigerant Safety Components shall include:

Thermal expansion devices (TXV's) shall be factory mounted and provided, Filter/strainer to eliminate any foreign matter, reversing valves to control refrigerant flow.

CONTROLS

Simple Control Circuit -

Field thermostat wiring connects to color coded leads using twist on wire connections. Cooling controls use contactor and relays for simple application and troubleshooting. Mate-n-lock plug connectors are used. The electrical control box is not located in the compressor com partment. The controls are mounted to allow the separate access panel to be removed for trouble shooting and mainte nance without affecting the normal system operating pres sures. All wiring internal to the unit is color/number coded.

• • •

Pressure Switches -

A high pressure switch is standard in all units. It is an automatic reset switch. When discharge pressure reaches 650 psi, the compressor will de-energize until pressure reaches 450 psi.

Factory Testing -

Installation time and costs are reduced by easy power and control wiring connections. All units are completely wired, charged with R-410A and tested prior to shipment. Test stations using a state-of-the-art computerized process system shall be used to insure product quality.

Refrigerant charge and component part numbers are verified via computer bar code scans during assembly. Vital run test statistics such as system pressure, motor currents, air veloc ity and temperature, unit vibration, and gas system safeties are monitored and recorded by the system to insure unit per formance. This data could be provided by serial number tracking if requested.

Electric Heat -

All electric heat models use 6HK electric heat, which are available in 460V/3/60 10kW to 25kW.

6 Johnson Controls Unitary Products

5564252-YTG-A-1018

PHYSICAL DATA

MODELS: NOMINAL TONNAGE: AHRI Cooling Performance

Gross Capacity @ AHRI A point (MBH) AHRI net capacity (MBH) EER SEER Nominal CFM System power (KW) Refrigerant type Refrigerant charge (lb-oz)

Dimensions (inches)

Length Width Height

Operating WT. (lbs.) Compressors

Type

Outdoor Coil Data

Face area (Sq. Ft.) Rows Fins per inch Tube diameter Circuitry Type

Indoor Coil Data

Face area (Sq. Ft.) Rows Fins per inch Tube diameter Circuitry Type Refrigerant control

Outdoor Fan Data

Fan diameter (Inch) Type Drive type No. speeds Motor HP each RPM Nominal total CFM

Direct Drive Indoor Fan Data

Fan Size (Inch) Type Motor HP each RPM Frame size

Filters

Filter Size Quantity - Size

PCE4A3642 3.0

37.2

34.6

11.0

14.0

1200 3.2

R410A 8-8 51-1/4 35-3/4 47 382 Scroll 15.1

2 22 3/8 Interlaced 4.6

3 16 3/8 Interlaced TXV 24 Prop Direct 1 1/4 850 2400 11 x 10 Centrifugal 1/2 1200 Max 48

PCE4B4842 4.0

47.7

45.5

11.0

14.0

1600 4.2

R410A 11-3 51-1/4 45-3/4 49 455 Scroll 19.5

2 22 3/8 Interlaced 6.3

3 16 3/8 Interlaced TXV 26 Prop Direct 1 1/3 850 3200 11 x 10 Centrifugal 1 1200 Max 48

PCE4B6042 5.0

55.0

52.5

11.0

14.0

2000 4.8

R410A 12-0 51-1/4 45-3/4 51 472 Scroll 21.5

2 22 3/8 Interlaced 6.3

3 16 3/8 Interlaced TXV 26 Prop Direct 1 1/3 850 3200 11 x 10 Centrifugal 1 1200 Max 48 A B B Field-supplied external filters must be sized so as not to exceed 300 FPM air velocity through dispos able filters. All 3-phase models are shipped with an internal filter rack kit. Consult the instructions sup plied with that kit for replacement filter sizes. Filter sizes: A=20x20, B=20x30.

Johnson Controls Unitary Products 7

5564252-YTG-A-1018

COOLING PERFORMANCE DATA - 3 TON

PACKAGED UNIT MODEL NO.

CONDENSER ENTERING AIR TEMPERATURE ID CFM IDDB IDWB 55 / 45

T.C.

S.C.

K.W.

T.C.

65 / 55 75 / 63 85 / 69

S.C.

K.W.

T.C.

S.C.

K.W.

T.C.

S.C.

K.W.

95 / 75 105 / 83 115 / 89 125 / 95

T.C.

S.C.

K.W.

T.C.

S.C.

K.W.

T.C.

S.C.

K.W.

T.C.

S.C.

K.W.

PCE4A3642 80 57

36.0

34.5

1.82

34.6

33.2

2.01

33.2

32.0

2.20

31.7

30.4

2.46

30.1

28.8

2.72

29.0

27.5

2.91

27.9

26.3

3.11

26.8

25.1

3.30

1000 75 62

40.3

27.6

1.83

37.4

26.0

2.02

34.5

24.5

2.21

32.2

23.3

2.47

29.8

22.2

2.73

27.8

20.9

2.95

25.9

19.6

3.17

24.0

18.3

3.39

80 62

38.3

30.6

1.83

36.4

29.8

2.02

34.6

28.9

2.20

32.6

26.9

2.44

30.6

25.0

2.67

28.3

23.9

2.92

26.0

22.9

3.16

23.8

21.9

3.39

80 67

44.9

27.9

1.83

42.6

26.8

2.03

40.3

25.7

2.22

37.8

24.6

2.48

35.3

23.4

2.74

32.8

21.8

2.96

30.4

20.3

3.19

28.0

18.7

3.41

8

COOLING PERFORMANCE DATA - 4 TON

PACKAGED UNIT MODEL NO.

PCE4B4842 CONDENSER ENTERING AIR TEMPERATURE 55 / 45 65 / 55 75 / 63 85 / 69 95 / 75 105 / 83 115 / 89 125 / 95 ID CFM IDDB IDWB

T.C.

S.C.

K.W.

T.C.

S.C.

K.W.

T.C.

S.C.

K.W.

T.C.

S.C.

K.W.

T.C.

S.C.

K.W.

T.C.

S.C.

K.W.

T.C.

S.C.

K.W.

T.C.

S.C.

K.W.

80 57

50.7

48.2

2.48

48.0

44.3

2.76

45.4

40.3

3.04

42.9

38.3

3.41

40.4

36.4

3.79

36.7

32.3

4.30

33.1

28.4

4.80

29.5

24.5

5.30

1400 75 62

54.4

38.3

2.51

51.2

36.7

2.79

48.1

35.0

3.06

44.9

33.2

3.42

41.7

31.4

3.78

37.5

29.7

4.29

33.3

28.0

4.79

29.2

26.4

5.30

80 62

55.0

44.8

2.52

52.0

43.2

2.79

49.0

41.7

3.06

45.4

39.8

3.42

41.8

38.0

3.79

37.6

34.7

4.30

33.6

31.6

4.80

29.5

28.4

5.29

80 67

59.4

38.5

2.54

57.1

37.1

2.81

54.9

35.7

3.08

51.3

33.7

3.44

47.7

31.8

3.80

43.5

30.0

4.32

39.4

28.4

4.83

35.3

26.7

5.33

80 72

48.1

22.6

1.85

46.1

21.6

2.04

44.0

20.7

2.23

41.2

19.3

2.49

38.4

17.9

2.74

36.1

16.9

2.97

33.9

15.9

3.20

31.7

14.9

3.42

80 57

38.9

37.1

1.89

37.3

35.6

2.09

35.7

34.1

2.28

34.0

32.4

2.53

32.3

30.8

2.79

31.1

29.4

2.95

30.0

28.1

3.10

28.9

26.8

3.25

80 62

40.4

33.8

1.90

38.3

32.9

2.09

36.3

32.0

2.28

34.0

30.3

2.53

31.7

28.6

2.77

29.6

27.1

3.01

27.4

25.8

3.24

25.3

24.4

3.47

1200 75 62

42.1

29.9

1.90

39.4

28.5

2.09

36.6

27.2

2.28

33.8

25.8

2.54

31.0

24.3

2.80

28.9

22.9

3.02

26.8

21.6

3.24

24.8

20.2

3.46

80 67

46.8

30.2

1.91

44.2

28.9

2.10

41.7

27.7

2.30

38.9

26.5

2.55

36.2

25.3

2.81

33.8

23.8

3.04

31.4

22.3

3.26

29.0

20.9

3.48

80 72

49.8

23.9

1.92

47.9

23.4

2.11

46.1

22.9

2.30

42.8

21.1

2.56

39.6

19.3

2.82

37.1

18.2

3.05

34.7

17.2

3.27

32.3

16.2

3.49

80 57

41.8

39.6

1.97

40.0

37.9

2.16

38.1

36.1

2.36

36.3

34.5

2.61

34.5

32.8

2.87

33.3

31.3

2.98

32.1

29.9

3.10

31.0

28.5

3.21

80 62

42.5

37.1

1.97

40.2

36.1

2.16

37.9

35.2

2.36

35.4

33.7

2.61

32.8

32.2

2.87

30.8

30.4

3.10

28.9

28.6

3.32

26.9

26.9

3.55

1400 75 62

43.9

32.2

1.98

41.3

31.0

2.17

38.7

29.9

2.36

35.4

28.2

2.61

32.1

26.5

2.87

29.9

25.0

3.10

27.8

23.5

3.32

25.6

22.1

3.54

80 67

48.8

32.5

1.99

45.9

31.1

2.18

43.1

29.7

2.37

40.1

28.4

2.63

37.1

27.2

2.88

34.7

25.8

3.11

32.3

24.4

3.33

30.0

23.1

3.55

80 72

51.5

25.1

1.99

49.8

25.1

2.19

48.2

25.0

2.38

44.5

22.8

2.63

40.8

20.7

2.89

38.1

19.6

3.12

35.5

18.5

3.35

33.0

17.4

3.57

80 72

65.3

30.4

2.56

62.8

29.6

2.83

60.3

28.7

3.11

56.4

27.3

3.46

52.4

25.9

3.82

47.8

23.9

4.34

43.4

21.9

4.85

39.0

19.9

5.35

80 57

53.0

49.3

2.56

50.3

46.3

2.83

47.5

43.4

3.10

44.8

41.4

3.47

42.1

39.4

3.85

38.1

34.3

4.36

34.1

29.4

4.87

30.2

24.5

5.37

80 62

56.8

48.2

2.59

53.6

46.6

2.85

50.4

45.1

3.12

46.6

42.4

3.49

42.7

39.7

3.85

38.4

36.1

4.36

34.3

32.5

4.86

30.1

29.0

5.36

1600 75 62

56.1

41.0

2.58

52.9

39.3

2.85

49.6

37.6

3.12

46.1

35.7

3.48

42.6

33.8

3.83

38.0

31.1

4.35

33.6

28.6

4.86

29.2

26.0

5.36

80 67

61.2

40.7

2.61

58.7

39.4

2.88

56.2

38.1

3.14

52.5

36.3

3.50

48.7

34.5

3.86

44.3

32.6

4.38

40.0

30.7

4.89

35.7

28.8

5.39

1800 75 62

57.9

43.6

2.64

54.5

41.9

2.91

51.1

40.2

3.18

47.2

38.2

3.54

43.4

36.2

3.89

38.6

32.6

4.41

33.8

29.1

4.92

29.1

25.6

5.42

80 67

63.1

42.9

2.67

60.3

41.7

2.94

57.5

40.5

3.21

53.6

38.9

3.57

49.7

37.3

3.92

45.1

35.1

4.44

40.6

33.0

4.95

36.1

31.0

5.45

80 72

69.1

33.4

2.68

66.0

32.1

2.95

62.9

30.8

3.23

59.1

29.4

3.59

55.2

28.1

3.95

50.0

26.0

4.47

45.0

23.9

4.97

40.0

21.9

5.47

5564252-YTG-A-1018

COOLING PERFORMANCE DATA - 5 TON

PACKAGED UNIT MODEL NO.

CONDENSER ENTERING AIR TEMPERATURE ID CFM IDDB IDWB 55 / 45

T.C.

S.C.

K.W.

65 / 55

T.C.

S.C.

K.W.

T.C.

75 / 63 85 / 69 95 / 75

S.C.

K.W.

T.C.

S.C.

K.W.

T.C.

S.C.

K.W.

105 / 83 115 / 89 125 / 95

T.C.

S.C.

K.W.

T.C.

S.C.

K.W.

T.C.

S.C.

K.W.

PCE4B6042 80 57

68.0

63.3

2.93

64.1

60.3

3.25

60.2

57.4

3.56

57.4

55.0

3.98

54.5

52.6

4.40

52.1

49.5

5.03

49.8

46.6

5.65

47.5

43.6

6.27

1600 75 62

68.1

46.2

2.97

64.3

44.6

3.28

60.5

43.1

3.59

56.2

41.1

4.01

52.0

39.2

4.42

45.9

36.3

4.99

40.0

33.4

5.54

34.1

30.6

6.09

80 62

69.1

54.8

2.97

65.4

53.4

3.27

61.8

52.0

3.58

57.1

49.4

4.00

52.4

46.9

4.42

47.2

42.1

4.99

42.2

37.5

5.54

37.1

32.8

6.09

80 67

73.0

43.7

3.00

69.7

43.2

3.31

66.4

42.7

3.63

61.8

40.5

4.04

57.1

38.2

4.44

51.1

36.0

5.01

45.3

33.8

5.57

39.5

31.6

6.12

80 72

79.5

36.0

3.03

75.7

34.9

3.35

72.0

33.7

3.67

67.1

31.6

4.07

62.3

29.4

4.48

55.2

26.7

5.05

48.3

24.0

5.60

41.4

21.3

6.15

80 57

70.4

66.7

3.15

66.2

62.8

3.46

62.1

59.0

3.78

58.7

56.2

4.19

55.3

53.5

4.61

52.5

50.0

5.22

49.8

46.6

5.80

47.1

43.1

6.39

80 62

70.4

57.0

3.17

66.4

55.9

3.48

62.5

54.7

3.79

57.8

52.2

4.21

53.0

49.7

4.62

47.6

44.0

5.19

42.3

38.4

5.75

36.9

32.9

6.30

1800 75 62

69.3

48.8

3.18

65.1

46.7

3.49

60.9

44.7

3.80

56.6

43.1

4.21

52.3

41.5

4.62

45.6

37.3

5.19

39.0

33.3

5.74

32.5

29.2

6.30

80 67

74.8

46.3

3.21

71.0

45.4

3.52

67.1

44.5

3.84

62.3

42.5

4.24

57.5

40.4

4.65

51.0

37.8

5.22

44.7

35.3

5.77

38.3

32.8

6.32

80 72

80.8

37.1

3.24

76.5

35.7

3.56

72.2

34.3

3.88

67.4

32.8

4.28

62.6

31.2

4.68

55.2

28.1

5.25

47.9

25.0

5.80

40.7

21.9

6.35

80 57

72.7

70.1

3.36

68.4

65.3

3.68

64.0

60.6

3.99

60.0

57.5

4.41

56.1

54.4

4.82

52.8

50.4

5.40

49.7

46.6

5.96

46.6

42.7

6.52

80 62

71.7

59.2

3.38

67.5

58.3

3.69

63.2

57.5

4.00

58.4

55.0

4.42

53.7

52.5

4.83

47.9

45.8

5.40

42.3

39.4

5.95

36.8

32.9

6.51

2000 75 62

70.5

51.4

3.38

65.9

48.9

3.69

61.4

46.3

4.01

57.0

45.1

4.42

52.5

43.8

4.83

45.2

38.3

5.40

38.1

33.1

5.95

31.0

27.8

6.50

80 67

76.6

48.8

3.42

72.3

47.6

3.73

67.9

46.3

4.04

62.9

44.5

4.45

57.9

42.6

4.86

50.9

39.7

5.42

44.0

36.9

5.97

37.2

34.1

6.52

80 72

82.2

38.2

3.45

77.4

36.5

3.77

72.5

34.9

4.08

67.7

33.9

4.48

62.9

33.0

4.88

55.1

29.5

5.45

47.5

26.0

6.00

39.9

22.6

6.55

Johnson Controls Unitary Products 9

5564252-YTG-A-1018 &2,/*8$5' +,*+92/7$*( 23(1,1*´ +,*+92/7$*( 23(1,1*´ &2035(6625 $&&(663$1(/ & +($76(&7,21 $&&(663$1(/ &21'(16$7( '5$,1 %/2:(5 $&&(66 3$1(/ $ &21752/+($7 $&&(663$1(/

UNIT DIMENSIONS & ACCESS LOCATIONS

Model

PCE4A3642 PCE4B4842 PCE4B6042

A

51-1/4 % /2:92/7$*(23(1,1*´

Dimensions - in inches B

35-3/4 45-3/4 45-3/4

C

47 49 51 $

UNIT CLEARANCES

Direction

Top 1

Distance (in.)

36

Direction

Right Side

Distance (in.)

36 Side Opposite Ducts Duct Panel 36 0 Left Side Bottom 2,3 24 1

NOTE:

For units applied with a roof curb, the minimum clearance may be reduced from 1 inch to 1/2 inch between combustible roof curb material and this supply air duct. 1. Minimum Clearance of 1inch all sides of supply air duct for the first 3 feet of duct for 20 & 25 kW., zero inches thereafter. For all other heaters, zero inch clearance all sides for entire length of duct.

2. Units must be installed outdoors. Overhanging structures or shrubs should not obscure outdoor air discharge outlet.

3. Units may be installed on combustible floors made from wood or class A, B or C roof covering materials.

ELECTRIC HEAT MINIMUM SUPPLY AIR

Model

PCE4A3642 PCE4B4842 PCE4B6042

Voltage

460-3-60

2 5

Low #1 Low #1 - - Low #1 Low #1

8

Low #1 Low #1 Low #1

Minimum Blower Speed for Electric Heat Heater kW 10

Low #1 Low #1 Low #1

13

Med. Low #2 Low #1 Low #1

15

High #5 Low #1 Low #1

18

--

20

--

25

- Med. Low #2 Med. High #4 Low #1 - Med. Low #2 Med. High #4 10 Johnson Controls Unitary Products

5564252-YTG-A-1018

INDOOR BLOWER SPECIFICATIONS

Model

PCE4A3642 PCE4B4842 PCE4B6042

SOUND PERFORMANCE

Model (Tons)

PCE4A3642 PCE4B4842 PCE4B6042

Sound Rating 1 dB (A)

74 74 76 1. Rated in accordance with AHRI Standard 270.

HP

1/2 1 1

125

58.5

63.5

72.3

460V - 3 PHASE SINGLE-POINT KITS

Unit Model Number

PCE4A3642 PCE4B4842 PCE4B6042

Voltage

460-3-60 460-3-60 460-3-60

Heater Kit

6HK06501046 6HK06501546 6HK06501046 6HK06501546 6HK06501846 6HK16502046 6HK06501046 6HK06501546 6HK06501846 6HK16502046 6HK16502546

RPM

Variable

Motor EFF.

0.8

SF

1.0

250

61.8

63.9

65.0

Octave Band Centerline Frequency (Hz) 500 1000 2000

65.4

62.3

63.9

66.5

65.0

64.0

60.7

64.0

60.0

4000

54.8

54.1

55.5

Frame

48

8000

49.8

46.6

49.0

Single-Point Wiring Kit Unit Fuse Size (Amps) Heater Fuse Size (Amps)

S1-2SPWK036 15 15 S1-2SPWK036 S1-2SPWK036 15 15 25 15 S1-2SPWK036 S1-2SPWK036 S1-2SPWK036 S1-2SPWK036 15 15 15 20 25 25 30 15 S1-2SPWK036 S1-2SPWK036 S1-2SPWK036 S1-2SPWK037 20 20 20 20 25 25 30 35

ELECTRICAL DATA - 460-3-60 SINGLE SOURCE POWER

Model

A36 B48

Compressor RLA LRA MCC FLA

5.8 38.0

9.0

OD Fan Motor Blower Motor

0.70

FLA

1.95

Electric Heat Option Heater Kit Heater Stages kW Heater MCA 1 (Total Unit) Amps Max Fuse 2 or Breaker Size 3 (Total Unit) MCA 1 (Unit Minus Heater) Max Fuse 2 or Breaker Size 3 (Unit Minus Heater) Only) Max Fuse 2 MCA 1 Unit (Heater or Breaker Size 3 (Unit Minus Heater)

none 6HK06501046 - 8.8

- 1 - 11.0

9.9

13.0

15 15 9.9

9.9

15 15 13.8

15 6.2 41.0

9.7

0.87

3.15

6HK06501546 none 6HK06501046 6HK06501546 13.2

- 8.8

13.2

1 - 1 1 16.6

- 11.0

16.6

18.5

11.8

17.0

23.9

25 15 20 25 9.9

11.8

11.8

11.8

20 15 15 15 20.7

13.8

20.7

25 15 25 6HK06501846 6HK06502046 none 6HK06501046 15.9

17.6

- 8.8

1 1 - 1 20.0

22.1

- 11.0

28.1

30.8

13.8

17.0

30 35 20 20 11.8

11.8

13.8

13.8

15 15 20 20 25.0

27.6

13.8

25 30 15 B60 7.8 52.0 12.1 0.87

3.15

6HK06501546 6HK06501846 6HK06502046 6HK06502546 13.2

15.9

17.6

22.0

1 1 1 1 16.6

20.0

22.1

27.6

23.9

28.1

30.8

37.7

25 30 35 40 13.8

13.8

13.8

13.8

20 20 20 20 20.7

25.0

27.6

34.5

25 25 30 35

NOTE

- Single-source power MCA and MOP requirements are given here for reference if the unit is to be installed with a field-installed single-point power modification.

1.Minimum Circuit Ampacity.

2.Maximum Over Current Protection per standard UL 1995.

3. Fuse or HACR circuit breaker size to be field installed.

Johnson Controls Unitary Products 11

5564252-YTG-A-1018

ELECTRICAL DATA FOR 460-3-60 MULTI SOURCE POWER

Model

A36 B48 B60

RLA

5.8

6.2

7.8

Compressor LRA

38.0

41.0

52.0

MCC

9.0

9.7

12.1

OD Fan Motor Blower Motor FLA

0.7

0.87

0.87

FLA

1.95

3.15

3.15

Heater Kit

none 6HK06501046 6HK06501546 none 6HK06501046 6HK06501546 6HK06501846 6HK06502046 none 6HK06501046 6HK06501546 6HK06501846 6HK06502046 6HK06502546

Electric Heat Option Heater kW

- 8.8

13.2

- 8.8

13.2

15.9

17.6

- 8.8

13.2

15.9

17.6

22.0

Stages Heater Amps

- 1 1 - 1 1 1 1 - 1 1 1 1 1 - 11.0

16.6

- 11.0

16.6

20.0

22.1

- 11.0

16.6

20.0

22.1

27.6

MCA Amps Max Fuse or Breaker Size MCA Amps Max Fuse or Breaker Size CIRCUIT #1 CIRCUIT #2 Unit Minus Heaters Heaters

9.9

9.9

9.9

11.8

15 15 15 15 - 13.8

20.7

- - 15 25 - 11.8

11.8

11.8

11.8

13.8

13.8

13.8

13.8

13.8

13.8

15 15 15 15 20 20 20 20 20 20 13.8

20.7

25.0

27.6

- 13.8

20.7

25.0

27.6

34.5

15 25 25 30 - 15 25 25 30 35 "D" CENTER OF GRAVITY COMPRESSOR "A" "C" FRONT OF UNIT

WEIGHTS AND DIMENSIONS

Model

PCE4A3642 PCE4B4842 PCE4B6042

Weight (lbs.) Shipping

387 460 477

Operating

382 455 472 X

Center of Gravity X

30

Y

15 19 20 "B" Y A0295-001-TG

A

112 158 157

4 Point Load Location (lbs.) B

123 125 134

C

120 130 140

D

45 75 74 12 Johnson Controls Unitary Products

AIRFLOW PERFORMANCE - SIDE DUCT APPLICATION

Model

PCE4A3642 PCE4B4842 PCE4B6042

Motor Speed

Low (1) Low/Medium (2) Medium (3) Medium/High (4) High (5) Low (1) Low/Medium (2) Medium (3) Medium/High (4) High (5) Low (1) Low/Medium (2) Medium (3) Medium/High (4) High (5)

0.1

SCFM

1225 1259 1314 1348 1506 1620 1694 1798 1835 2146 1730 1858 2054 2195 2445

0.2

SCFM

1174 1209 1271 1306 1471 1564 1630 1722 1758 2085 1682 1807 1998 2144 2388

0.3

SCFM External Static Pressure (Inches WC) 0.4

0.5

0.6

SCFM SCFM SCFM 0.7

SCFM

1131 1166 1090 1126 1046 1084 993 1032 941 980 1229 1259 1403 1517 1580 1669 1703 2025 1628 1749 1934 2098 2306 1186 1222 1389 1466 1530 1620 1653 1960 1592 1710 1890 2049 2293 1144 1179 1345 1418 1482 1572 1604 1872 1552 1667 1843 2003 2235 1097 1133 1305 1360 1430 1527 1558 1862 1517 1629 1801 1955 2178 1. Airflow tested with dry coil conditions, without air filters, at 460 volts.

2. Applications above 0.8" w.c. external static pressure are not recommended.

3. Brushless DC high efficiency standard ECM blower motor used for all indoor blower assemblies.

4. Heating applications tested at 0.50" w.c. esp, and cooling capacity applications tested at 0.30" w.c.esp per standards.

1049 1086 1262 1308 1380 1480 1511 1798 1479 1589 1757 1883 2129

AIRFLOW PERFORMANCE - BOTTOM DUCT APPLICATION

Model

PCE4A3642 PCE4B4842 PCE4B6042

Motor Speed

Low (1) Low/Medium (2) Medium (3) Medium/High (4) High (5) Low (1) Low/Medium (2) Medium (3) Medium/High (4) High (5) Low (1) Low/Medium (2) Medium (3) Medium/High (4) High (5)

0.1

SCFM

1231 1270 1317 1358 1517 1598 1663 1789 1931 2131 1655 1766 1987 2114 2369

0.2

SCFM

1186 1225 1286 1317 1475 1548 1612 1733 1814 2058 1612 1720 1933 2050 2308 1568 1670 1808 1998 1596 1667 1861 2047 2249

0.3

SCFM External Static Pressure (Inches WC) 0.4

0.5

0.6

SCFM SCFM SCFM 0.7

SCFM

1146 1189 1103 1140 1069 1098 1030 1046 977 1008 1245 1275 1447 1502 1198 1238 1400 1454 1151 1197 1357 1410 1110 1148 1318 1362 1064 1105 1275 1307 1522 1650 1736 1949 1531 1629 1817 1974 2183 1476 1596 1673 1892 1461 1632 1820 1899 2126 1422 1578 1650 1840 1462 1539 1715 1889 2088 1370 1535 1597 1788 1429 1537 1725 1920 2034 1. Airflow tested with dry coil conditions, without air filters, at 460 volts 2. Applications above 0.8" w.c. external static pressure are not recommended.

3. Brushless DC high efficiency standard ECM blower motor used for all indoor blower assemblies.

4. Heating applications tested at 0.50" w.c. esp, and cooling capacity applications tested at 0.30" w.c.esp per standards.

5564252-YTG-A-1018

0.8

SCFM

888 928 998 1036 1216 1206 1292 1413 1442 1735 1439 1546 1710 1868 2077

0.8

SCFM

912 960 1024 1057 1232 1251 1297 1483 1519 1728 1391 1498 1651 1866 1990

1.0

SCFM

782 824 896 936 1124 1002 1116 1280 1304 1609 1359 1460 1616 1838 1973

1.0

SCFM

781 866 943 961 1146 1139 1152 1379 1362 1608 1316 1421 1504 1758 1902 Johnson Controls Unitary Products 13

5564252-YTG-A-1018

ADDITIONAL STATIC RESISTANCE

Size (Tons)

36 (3.0) 48 (4.0) 60 (5.0)

CFM

700 800 900 1000 1100 1200 1300 1400 1100 1200 1300 1400 1500 1600 1700 1800 1900 2000 1100 1200 1300 1400 1500 1600 1700 1800 1900 2000

Wet Indoor Coil

0.01

0.02

0.03

0.04

0.05

0.06

0.07

0.08

0.02

0.03

0.04

0.05

0.06

0.07

0.07

0.08

0.09

0.09

0.02

0.03

0.04

0.05

0.06

0.07

0.07

0.08

0.09

0.09

Economizer 1

0.00

0.01

0.01

0.01

0.01

0.02

0.03

0.04

0.02

0.02

0.02

0.03

0.04

0.04

0.04

0.04

0.05

0.05

0.02

0.02

0.02

0.03

0.04

0.04

0.04

0.04

0.05

0.05

NOTE: Filter/Frame Kit

0.04

0.06

0.08

0.10

0.13

0.16

0.17

0.18

0.04

0.04

0.05

0.05

0.06

0.07

0.08

0.09

0.10

0.11

0.04

0.04

0.05

0.05

0.06

0.07

0.08

0.09

0.10

0.11

1. The pressure drop through the economizer is greater for 100% outdoor air than for 100% return air. If the resistance of the return air duct is less than 0.25 IWG, the unit will deliver less CFM during full economizer operation.

Filter pressure drop based on standard filter media tested at velocities not to exceed 300 ft/min.

DUCT DIMENSIONS (Inches) - BOTTOM VIEW LOOKING UP

& $ % $ ' 5(7851 $,5'8&7 9,(:/22.,1*83 $7%277202)81,7 +2/( ´IRUKLJKYROWDJH 6833/< $,5'8&7 +2/( ´IRU ORZYROWDJH (

Model

A36 B48, B60

A

10 14

B

21.5

13.5

)

C

5

D

4.5

3.5

E

47.5

$

F

32 42

DUCT DIMENSIONS (Inches) - REAR VIEW

127(6HH)LJXUHWLWOHG³8QLW'LPHQVLRQV´IRUVLGHKROHVL]HVRI HOHFWULFDOOLQHV 14 6833/< $,5'8&7 5(7851 $,5'8&7 $

Model

A36 B48, B60 $ %

A

9.6

13.6

$

B

22 14 Johnson Controls Unitary Products

5564252-YTG-A-1018

UNIT TYPICAL DUCT APPLICATIONS

ROOF CURB INSTALLATION REAR DUCT ROOF CURB INSTALLATION BOTTOM DUCT

UNIT TYPICAL SLAB ON GROUND INSTALLATION

CONDENSATE DRAIN Johnson Controls Unitary Products SLAB ON GROUND INSTALLATION A0324-001 TO POWER SUPPLY RETURN AIR DUCT CONTROL WIRING TO INDOOR THERMOSTAT SUPPLY AIR DUCT FIELD-SUPPLIED DISCONNECT SWITCH A0390-001 15

UNIT TYPICAL ROOF CURB INSTALLATION

CONDENSATE DRAIN ROOF CURB FIELD-SUPPLIED DISCONNECT SWITCH TO POWER SUPPLY CONTROL WIRING TO INDOOR THERMOSTAT RETURN AIR DUCT SUPPLY AIR DUCT ROOF A0389-001 Subject to change without notice. Published in U.S.A.

Copyright © 2018 by Johnson Controls, Inc. All rights reserved.

York International Corp.

5005 York Drive Norman, OK 73069

5564252-YTG-A-1018 Supersedes: 5163622-YTG-H-1117

Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project