Biostar J3160NH Motherboard Manual

Add to My manuals
26 Pages

advertisement

Biostar J3160NH Motherboard Manual | Manualzz

J3160MP UEFI BIOS Manual

UEFI BIOS Setup ........................................................................... 1

1 Main Menu ................................................................................... 3

2 Advanced Menu .......................................................................... 4

3 Chipset Menu ............................................................................ 16

4 Security Menu ........................................................................... 19

5 Boot Menu ................................................................................. 22

6 Performance Menu ................................................................... 23

7 Exit Menu .................................................................................. 25 i

J3160MP UEFI BIOS Manual

UEFI BIOS Setup

Introduction

The purpose of this manual is to describe the settings in the AMI UEFI

BIOS Setup program on this motherboard. The Setup program allows users to modify the basic system configuration and save these settings to

NVRAM.

UEFI BIOS determines what a computer can do without accessing programs from a disk. This system controls most of the input and output devices such as keyboard, mouse, serial ports and disk drives. BIOS activates at the first stage of the booting process, loading and executing the operating system. Some additional features, such as virus and password protection or chipset fine-tuning options are also included in

UEFI BIOS.

The rest of this manual will to guide you through the options and settings in UEFI BIOS Setup.

Plug and Play Support

This AMI UEFI BIOS supports the Plug and Play Version 1.0A specification.

EPA Green PC Support

This AMI UEFI BIOS supports Version 1.03 of the EPA Green PC specification.

ACPI Support

AMI ACPI UEFI BIOS support Version 1.0/2.0 of Advanced Configuration and Power interface specification (ACPI). It provides ASL code for power management and device configuration capabilities as defined in the ACPI specification, developed by Microsoft, Intel and Toshiba.

PCI Bus Support

This AMI UEFI BIOS also supports Version 2.3 of the Intel PCI (Peripheral

Component Interconnect) local bus specification.

DRAM Support

DDR3L SO-DRAM (Double Data Rate III Synchronous DRAM) is supported.

1

J3160MP UEFI BIOS Manual

Using Setup

When starting up the computer, press <Del> during the Power-On

Self-Test (POST) to enter the UEFI BIOS setup utility.

In the UEFI BIOS setup utility, you will see General Help description at the top right corner, and this is providing a brief description of the selected item. Navigation Keys for that particular menu are at the bottom right corner, and you can use these keys to select item and change the settings.

General Help

Navigation Keys

Notice

 The default UEFI BIOS settings apply for most conditions to ensure optimum performance of the motherboard. If the system becomes unstable after changing any settings, please load the default settings to ensure system’s compatibility and stability. Use Load Setup

Default under the Exit Menu.

 For better system performance, the UEFI BIOS firmware is being continuously updated. The UEFI BIOS information described in this manual is for your reference only. The actual UEFI BIOS information and settings on board may be slightly different from this manual.

 The content of this manual is subject to be changed without notice.

We will not be responsible for any mistakes found in this user’s manual and any system damage that may be caused by wrong-settings.

2

J3160MP UEFI BIOS Manual

1 Main Menu

Once you enter AMI UEFI BIOS Setup Utility, the Main Menu will appear on the screen providing an overview of the basic system information.

BIOS Information

It shows system information including UEFI BIOS version, Project Code,

Model Name, Build Date and etc.

Total Memory

Shows system memory size, VGA shard memory will be excluded.

System Language

Choose the system default language.

System Date

Set the system date. Note that the ‘Day’ automatically changes when you set the date.

System Time

Set the system internal clock.

3

J3160MP UEFI BIOS Manual

2 Advanced Menu

The Advanced Menu allows you to configure the settings of CPU, Super

I/O, Power Management, and other system devices.

Notice

Beware of that setting inappropriate values in items of this menu may cause system to malfunction.

ACPI Settings

Enable ACPI Auto Configuration

This item enables or disables BIOS ACPI Auto Configuration.

Options: Disabled (Default) / Enabled

4

J3160MP UEFI BIOS Manual

Enable Hibernation

This item enables or disables system ability to hibernate (OS/S4 Sleep

State). This option may be not effective with some OSes.

Options: Enabled (Default) / Disabled

ACPI Sleep State

This item selects the highest ACPI sleep state the system will enter when the SUSPEND button is pressed.

Options: S3 (Suspend to RAM) (Default) / Suspend Disabled

Lock Legacy Resources

The item enables or disables Lock of Legacy Resources.

Options: Disabled (Default) / Enabled

PS2 Keyboard PowerOn

This item allows you to control the keyboard power on function.

Options: Disabled (Default) / Any Key / Stroke Key / Specific Key

Stroke Keys

This item will show only when Keyboard PowerOn is set “Stroke Key.”

Options: Wake Key (Default) / Power Key / Ctrl+F1 / Ctrl+F2 / Ctrl+F3 /

Ctrl +F4 / Ctrl+F5 / Ctrl+F6

Specific Key

This item will show only when Keyboard PowerOn is set “Specific Key.”

Press Enter to set Specific key.

PS2 Mouse PowerOn

This item allows you to control the mouse power on function.

Options: Disabled (Default) / Enabled

Restore AC Power Loss

Specify what state to go to when power is re-applied after a power failure.

Options: Power Off (Default) / Power On / Last State

EuP Control

When EuP is enabled, the system will meet EuP requirement.

Options: Disabled (Default) / Enabled

PME Wake up from S5

The item enables the system to wake from S5 using PME event.

Options: Disabled (Default) / Enabled

5

J3160MP UEFI BIOS Manual

Wake system with Fixed Time

This item enables or disables the system to wake on by alarm event.

When this item is enabled, the system will wake on the hr::min::sec specified.

Options: Disabled (Default) / Enabled

Wake up date

You can choose which date the system will boot up.

Wake up hour / Wake up minute / Wake up second

You can choose the system boot up time, input hour, minute and second to specify.

USB Device Wakeup from S3/S4

This item allows you to enable or disabled the USB resume from S3/S4 function.

Options: Disabled (Default) / Enabled

Super IO Configuration

6

J3160MP UEFI BIOS Manual

Serial Port 1 Configuration

Serial Port

This item enables or disables Serial Port (COM1).

Options: Enabled (Default) / Disabled

Change Settings

This item selects an optimal setting for Super IO device.

Options: Auto (Default) / IO=3F8h; IRQ=4 / IO=3F8h; IRQ=3, 4, 5, 6, 7, 9,

10, 11, 12 / IO=2F8h; IRQ=3, 4, 5, 6, 7, 9, 10, 11, 12 / IO=3E8h; IRQ=3,

4, 5, 6, 7, 9, 10, 11, 12 / IO=2E8h; IRQ=3, 4, 5, 6, 7, 9, 10, 11, 12

Serial Port 2 Configuration

Serial Port

This item enables or disables Serial Port (J_COM2).

Options: Enabled (Default) / Disabled

7

J3160MP UEFI BIOS Manual

Change Settings

This item selects an optimal setting for Super IO device.

Options: Auto (Default) / IO=2F8h; IRQ=3 / IO=3F8h; IRQ=3, 4, 5, 6, 7, 9,

10, 11, 12 / IO=2F8h; IRQ=3, 4, 5, 6, 7, 9, 10, 11, 12 / IO=3E8h; IRQ=3,

4, 5, 6, 7, 9, 10, 11, 12 / IO=2E8h; IRQ=3, 4, 5, 6, 7, 9, 10, 11, 12

Parallel Port Configuration

Parallel Port

This item enables or disables Parallel Port (LPT/LPTE).

Options: Enabled (Default) / Disabled

Change Settings

This item allows you to select an optimal setting for Super IO device.

Options: Auto (Default) / IO=378h; IRQ=5; DMA=3 / IO=378h; IRQ=5, 6,

7, 9, 10, 11, 12; DMA=1,3 / IO=278h; IRQ=5, 6, 7, 9, 10, 11, 12;

DMA=1,3 / IO=3BCh; IRQ=5, 6, 7, 9, 10, 11, 12; DMA=1,3

Device Mode

This item allows you to change the Printer Port mode.

Options: EPP mode & ECP mode (Default) / Standard Parallet Port mode(SPP) / EPP mode / ECP mode

8

H/W Monitor

J3160MP UEFI BIOS Manual

CPU Configuration

This item shows CPU Information

9

J3160MP UEFI BIOS Manual

Limit CPUID Maximum

Disabled for Windows XP

Options: Disabled (Default) / Enabled

Bi-directional PROCHOT

When a processor thermal sensor trips (either core) the PROCHOT# will be driven. If bi-direction is enabled, external agents can drive PROCHOT# to throttle the processor.

Options: Enabled (Default) / Disabled

Intel Virtualization Technology

When enabled, a VMM can utilize the additional hardware capabilities provided by Vanderpool Technology

Options: Enabled (Default) / Disabled

Power Technology

This item enables or disables the power management features.

Options: Custom (Default) / Energy Efficient / Disable

EIST

This item enables or disables Intel SpeedStep.

Options: Enabled (Default) / Disabled

Turbo Mode

This item enables or disables Turbo Mode.

Options: Enabled (Default) / Disabled

P-STATE Coordination

This item changes P-STATE coordination type.

Options: HW_ALL (Default) / SW_ALL / SW_ANY

Package C State limit

This item sets Package C State limit.

Options: C1 (Default) / C3 / C6 / C7

10

J3160MP UEFI BIOS Manual

SATA Configuration

The BIOS will automatically detect the presence of SATA devices.

Serial-ATA (SATA)

This item enables/disables Serial ATA Device.

Options: Enabled (Default) / Disabled

SATA Mode

This item determines how SATA controller(s) operate.

Options: AHCI Mode (Default)

SATA1/2

This item enables/disables Serial ATA Port1/2.

Options: Enabled (Default) / Disabled

Network Stack Configuration

11

J3160MP UEFI BIOS Manual

Network Stack

This item enables or disables UEFI network stack

Options: Disabled (Default) / Enabled

Note: The following items appear only when you set the Network Stack function to

[Enabled]

IPv4 PXE Support

This item enables or disables IPv4 PXE Boot Support. If disabled IPv4 booth option will not be created.

Options: Enabled (Default) / Disabled

IPv6 PXE Support

This item enables or disables IPv6 PXE Boot Support. If disabled IPv6 booth option will not be created.

Options: Enabled (Default) / Disabled

PXE boot wait time

Wait time to press ESC key to abort the PXE boot.

Media detect count

Number of times presence of media will be checked.

CSM Configuration

CSM Support

This item enables or disables CSM Support

Options: Enabled (Default) / Disabled

12

J3160MP UEFI BIOS Manual

GateA20 Active

Upon Request – FA20 can be disabled using BIOS services. Always – do not allow disabling GA20; this option is useful when any RT code is executed above 1MB

Options: Upon Request (Default) / Always

Option ROM Messages

This item sets the display mode for option ROM.

Options: Force BIOS (Default) / Keep Current

Boot option filter

This option controls what devices system can boot to.

Options: UEFI and Legacy (Default) / Legacy only / UEFI only

Network

This item controls the execution of UEFI and Legacy PXE OpROM

Options: Legacy (Default) / Do not launch / UEFI

Storage

This item controls the execution of UEFI and Legacy Storage OpROM

Options: Legacy (Default) / Do not launch / UEFI

Video

This item controls the execution of UEFI and Legacy Video OpROM

Options: Legacy (Default) / Do not launch / UEFI

Other PCI device

It determines OpROM execution policy for devices other than Network,

Storage, or video.

Options: Legacy (Default) / Do not launch / UEFI

13

J3160MP UEFI BIOS Manual

USB Configuration

Legacy USB Support

The item allows you to enable Legacy USB support. AUTO option disables legacy support if no USB devices are connected. DISABLE option will keep USB devices available only for EFI applications.

Options: Enabled (Default) / Disabled / Auto

XHCI Hand-off

This is workaround for OSes without XHCI hand-off support. The XHCI ownership change should be claimed by XHCI driver.

Options: Enabled (Default) / Disabled

EHCI Hand-off

This is workaround for OSes without EHCI hand-off support. The EHCI ownership change should be claimed by EHCI driver.

Options: Enabled (Default) / Disabled

USB Mass Storage Driver Support

The item allows you to enable or disable USB Mass Storage Driver

Support.

Options: Enabled (Default) / Disabled

USB transfer time-out

The time-out value for Control, Bulk, and Interrupt transfers.

Options: 20 sec (Default) / 1 sec / 5 sec / 10 sec

Device reset time-out

The item sets USB mass storage device Start Unit command time-out.

Options: 20 sec (Default) / 10 sec / 30 sec / 40 sec

14

J3160MP UEFI BIOS Manual

Device power-up delay

“Auto” uses default value: for a Root port it is 100ms, for a Hub port the delay is taken from Hub descriptor.

Options: Auto (Default) / Manual

Note: The following items appear only when you set the Device power-up delay function to [Manual]

Device power-up delay in seconds

Delay range is 1 ~ 40 seconds, in one second increments.

Options: 5 (Default)

15

J3160MP UEFI BIOS Manual

3 Chipset Menu

This section describes configuring the PCI bus system. PCI, or Personal

Computer Interconnect, is a system which allows I/O devices to operate at speeds nearing the speed of the CPU itself uses when communicating with its own special components.

Notice

Beware of that setting inappropriate values in items of this menu may cause system to malfunction.

North Bridge

16

J3160MP UEFI BIOS Manual

Integrated Graphics Device

Enable: Enable Integrated Graphics Device (IGD) when selected as the

Primary Video Adaptor. Disable: Always disable IGD.

Options: Enabled (Default) / Disabled

IGD Turbo Enable

Enable: IGD Turbo Enable. Disable: IGD Turbo Disable.

Options: Auto (Default) / Enabled / Disabled

Primary Display

This item selects which of IGD/PCIe Graphics device should be Primary

Display.

Options: Auto (Default) / IGD / PCIe

GFX Boost

This item enables/disables GFX Boost.

Options: Enabled (Default) / Disabled

PAVC

This item enables/disables Protected Audio Video Control.

Options: Enabled (Default) / Disabled

DVMT Pre-Allocated

This item selects DVMT 5.0 Pre-Allocated (Fixed) Graphics Memory size used by the Internal Graphics Device.

Options: 32M (Default) / 64M / 96M / 128M / 160M / 192M / 224M /

256M / 288M / 320M / 352M / 384M / 416M / 448M / 480M / 512M

DVMT Total Gfx Mem

This item selects DVMT5.0 Total Graphic Memory size used by the

Internal Graphics Device.

Options: 256MB (Default) / 128MB / MAX

Aperture Size

This item selects the Aperature Size.

Options: 256MB (Default) / 128MB / 512MB

GTT Size

This item selects the GTT Size.

Options: 4MB (Default) / 2MB / 8MB

RC6 (Render Standby)

This item enables or disables render standby support.

Options: Enabled (Default) / Disabled

17

J3160MP UEFI BIOS Manual

Max TOLUD

Maximum Value of TOLUD

Options: Dynamic (Default) / 2 GB / 2.25 GB / 2.5 GB / 2.75 GB / 3 GB

South Bridge

ASPM

This item sets PCI Express Active State Power Management settings.

Options: Disabled (Default) / L0s / L1 / L0sL1 / Auto

Speed

This item selects PCI Express port speed.

Options: Auto (Default) / Gen1 / Gen2

Onboard Lan

This item enables/disables the PCI Express Port 2 in the Chipset.

Options: Enabled (Default) / Disabled

Onboard LAN Option ROM

This item enables/disables Onboard LAN Option ROM.

Options: Disabled (Default) / Enabled

High Precision Timer

This item enables/disables the High Precision Event Timer.

Options: Disabled (Default) / Enabled

18

J3160MP UEFI BIOS Manual

4 Security Menu

Administrator Password

This item sets Administrator Password.

User Password

This item sets User Password.

Secure Boot Menu

Secure Boot

Secure Boot can be enabled if

1. System running in user mode with enrolled Platform Key (PK)

2.CSM function is disabled.

Options: Enabled (Default) / Disabled

19

J3160MP UEFI BIOS Manual

Secure Boot Mode

Secure Boot mode selector. 'Custom' Mode enables users to change

Image Execution policy and manage Secure Boot Keys.

Options: Standard (Default) / Custom

Note: The following items appear only when you set the Secure Boot Mode function to [Custom]

Key Management

Provision Factory Default Keys

Install factory default Secure Boot Keys when system is in setup mode..

Options: Disabled (Default) / Enabled

Enroll All Factory Default Keys

It allows you to immediately load/clear the default Security Boot keys,

Platform key (PK), Key-exchange Key (KEK), Signature database (db), and Revoked Signatures (dbx). The Platform Key (PK) state will change from Unloaded mode to Loaded mode. The settings are applied after reboot or at the next reboot.

Delete all Secure Boot variables

Force System to Setup Mode - clear all Secure Boot variables (PK, KEK, db, dbt, dbx). Change takes effect after reboot.

Save all Secure Boot variables

Store content of each Secure Boot variable (data format :

EFI_SIGNATURE_LIST) to a file matching the variable name on selected file system's root folder.

20

J3160MP UEFI BIOS Manual

Platform Key (PK)

Set new Key – Allows you set new PK file.

Delete Key – Allows you to delete the PK file from your system.

Key Exchange Key (KEK)

Set new Key – Allows you set new KEK file.

Append Key – Allows you append Var to KEK.

Delete Key – Allows you to delete the KEK file from your system.

Authorized Signature Database (DB)

Set new Key – Allows you set new DB file.

Append Key – Allows you append Var to DB.

Delete Key – Allows you to delete the DB file from your system.

Forbidden Signature Database (DBX)

Set new Key – Allows you set new DBK file.

Append Key – Allows you append Var to DBX.

Delete Key – Allows you to delete the DBX file from your system.

Authorized TimeStamps (DBT)

Set new Key – Allows you set new DBT file.

Append Key – Allows you append Var to DBT.

21

J3160MP UEFI BIOS Manual

5 Boot Menu

This menu allows you to setup the system boot options.

Setup Prompt Timeout

This item sets number of seconds to wait for setup activation key.

Options: 1 (Default)

Bootup NumLock State

This item selects the keyboard NumLock state.

Options: On (Default) / Off

Full Screen Logo Display

This item allows you to enable/disable Full Screen Logo Show function.

Options: Enabled (Default) / Disabled

BIOS Flash protection

While enabled, it can’t flash write and flash erase by SMI.

Options: Enabled (Default) / Disabled

Boot Success Beep

When this item is set to Enabled, BIOS will let user know boot success with beep.

Options: Enabled (Default) / Disabled

Boot Option Priorities

The items specify the boot device priority sequence from the available devices. The number of device items that appears on the screen depends on the number of devices installed in the system.

22

J3160MP UEFI BIOS Manual

6 Performance Menu

This submenu allows you to change voltage and clock of various devices.

(However, we suggest you use the default setting. Changing the voltage and clock improperly may damage the device.)

Notice

 Beware of that setting inappropriate values in items of this menu may cause system to malfunction.

 The options and default settings might be different by RAM or CPU models.

DRAM Voltage

This item sets DRAM Voltage.

Options: Auto (Default) / SPEC / 1.350V (default) / 1.500V (default)

DRAM Timing Select

This item sets DRAM Timing Select.

Options: Auto (SPD) (Default) / Manual

Note: The following items appear only when you set the DRAM Timing Select function to [Manual]

Memory Frequency

This item sets memory frequency.

Options: Auto (Default) / 1600 / 1067 / 800

CAS# Latency (tCL)

This item allows you to select CAS Latency, Range 4-24

Options: Auto (Default)

23

J3160MP UEFI BIOS Manual

RAS# to CAS# Delay (tRCD)

This item allows you to select Row Address to Column Address Delay,

Range 3-20

Options: Auto (Default)

Row Precharge Time (tRP)

This item allows you to select Row Precharge Time, Range 3-15

Options: Auto (Default)

RAS# Active Time (tRAS)

This item allows you to select Row Active Time, Range 9-63

Options: Auto (Default)

Write Recovery Time (tWR)

This item allows you to select Internal Write to Read Command Delay,

Range 5-16

Options: Auto (Default)

Row Refresh Cycle Time (tRFC)

This item allows you to select Minimum Refresh Recovery Time, Range

1-511

Options: Auto (Default)

Write to Read Delay (tWTR)

This item allows you to select Internal Write to Read Command Delay,

Range 3-31

Options: Auto (Default)

Active to Active Delay (tRRD)

This item allows you to select Row Active to Row Active Delay, Range

4-15

Options: Auto (Default)

Read CAS# Precharge (tRTP)

This item allows you to select Read to Precharge Delay, Range 4-15

Options: Auto (Default)

Minimum CAS Write Latency Time

This item allows you to select Minimum CAS Write Latency Range,

Range 5-12

Options: Auto (Default)

Four Active Window Delay (tFAW)

This item allows you to select Four Active Window Delay, Range 10-63

Options: Auto (Default)

24

J3160MP UEFI BIOS Manual

7 Exit Menu

This menu allows you to load the optimal default settings, and save or discard the changes to the BIOS items.

Discard Changes and Exit

Abandon all changes made during the current session and exit setup.

Save Changes and Reset

Reset the system after saving the changes.

Restore Defaults

This selection allows you to reload the BIOS when problem occurs during system booting sequence. These configurations are factory settings optimized for this system.

Launch EFI Shell from filesystem device

This item attempts to EFI Shell application (Shellx64.efi) from one of the available filesystem devices.

25

advertisement

Related manuals

advertisement