AG Neovo DR-17G, DR-22G User manual

AG Neovo DR-17G, DR-22G User manual
DR-17G & DR-22G LCD Monitor
displays.agneovo.com
User Manual
TABLE OF CONTENTS
Safety Information
Federal Communications Commission (FCC) Notice (U.S. Only) ............................................................ 4
WEEE ....................................................................................................................................................... 5
EMC Information ...................................................................................................................................... 6
Precautions
Notice ....................................................................................................................................................... 10
Cautions When Setting Up ....................................................................................................................... 11
Cautions When Using............................................................................................................................... 12
Cleaning and Maintenance....................................................................................................................... 13
Notice for the LCD Display ....................................................................................................................... 13
Chapter 1: Product Description
1.1 Packa ge Contents .............................................................................................................................. 15
1.2 Wall Mounting Installation Preparation ............................................................................................... 16
1.2.1
Wall Mounting .......................................................................................................................... 16
1.2.2
Removing the Base Stand....................................................................................................... 17
1.3 LCD Display Overview ....................................................................................................................... 18
1.3.1
Front View and Keypad Buttons .............................................................................................. 18
1.3.2
Rear View ................................................................................................................................ 20
Chapter 2: Making Connections
2.1 Connecting the Power ........................................................................................................................ 21
2.2 Connecting Input Source Signals ....................................................................................................... 22
2.2.1
Connecting a Computer .......................................................................................................... 22
Using VGA Cables ......................................................................................................................... 22
Using DVI Cables ........................................................................................................................... 22
Using HDMI Cables........................................................................................................................ 23
Using DisplayPort Cables .............................................................................................................. 23
Using RS232 Cables ...................................................................................................................... 24
Using Audio Cables ........................................................................................................................ 24
2.2.2
Connecting a Video Device ..................................................................................................... 25
Using Composite (CVBS) Cables .................................................................................................. 25
Using S-Video Cables .................................................................................................................... 26
Using HDMI Cables........................................................................................................................ 26
Using DisplayPort Cables .............................................................................................................. 27
Chapter 3: Using the LCD Display
3.1 Turning on the Power ......................................................................................................................... 28
3.2 Selecting the Input Source Signal ...................................................................................................... 28
3.3 Adjusting the Volume / Illuminator Function Hot Key.......................................................................... 29
3.3.1
Muting the Audio...................................................................................................................... 29
3.3.2
Illuminator Function Hot Key ................................................................................................... 29
3.4 Choosing Your Preferred Picture Settings .......................................................................................... 29
3.5 Using Picture-in-Picture (PIP) ............................................................................................................ 30
3.5.1
PIP/PBP Options ..................................................................................................................... 30
3.5.2
PIP/PBP Swap ........................................................................................................................ 31
2
TABLE OF CONTENTS
3.6 Using FREEZE Function .................................................................................................................... 31
3.7 Using Auto Adjustment Function ........................................................................................................ 32
3.8 Using ROTATE Function .................................................................................................................... 32
3.9 Locki ng the OSD Menu ...................................................................................................................... 33
Chapter 4: On Screen Display Menu
4.1 Using the OSD Menu ......................................................................................................................... 34
4.2 OSD Menu Tree ................................................................................................................................. 36
Chapter 5: Adjusting the LCD Display
5.1 Brightness .......................................................................................................................................... 39
5.2 Colour Temp. ...................................................................................................................................... 41
5.3 Image Setting ..................................................................................................................................... 42
5.4 Aspect Ratio ....................................................................................................................................... 45
5.5 PIP Setting ......................................................................................................................................... 46
5.6 Anti-Burn-in......................................................................................................................................... 48
5.7 OSD Setting ....................................................................................................................................... 49
5.8 Audio Setting ...................................................................................................................................... 50
5.9 System 1 ............................................................................................................................................ 51
5.10 System 2 .......................................................................................................................................... 53
5.11 EcoSmart Sensor ............................................................................................................................. 54
5.12 Input Select ...................................................................................................................................... 56
Chapter 6: Appendix
6.1 Warning Messages ............................................................................................................................. 57
6.2 Supported Resolutions ....................................................................................................................... 58
6.3 Troubleshooting .................................................................................................................................. 59
6.4 Transporting the LCD Display ............................................................................................................ 61
Chapter 7: Specifications
7.1 Display pecifications ........................................................................................................................ 62
7.2 Display Dimensions ............................................................................................................................ 63
7.2.1
DR-17G Dimensions ............................................................................................................... 63
7.2.2
DR-22G Dimensions ............................................................................................................... 63
3
SAFETY INFORMATION
Safety Information
Federal Communications Commission (FCC) Notice (U.S. Only)
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
•
Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
Use only an RF shielded cable that was supplied with the display when connecting this display to a computer
device.
To prevent damage which may result in fire or shock hazard, do not expose this appliance to rain or excessive
moisture.
THIS CLASS B DIGITAL APPARATUS MEETS ALL REQUIREMENTS OF THE CANADIAN INTERFERENCECAUSING EQUIPMENT REGULATIONS.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
4
SAFETY INFORMATION
WEEE
Information for users applicable in European Union countries.
The symbol on the product or its packaging signifies that this product has to be
disposed separately from ordinary household wastes at its end of life. Please
kindly be aware that this is your responsibility to dispose electronic equipment at
recycling centers so as to help conserve natural resources. Each country in the
European Union should have its collection centers for electrical and electronic
equipment recycling. For information about your recycling drop off area, please
contact your local related electrical and electronic equipment waste management
authority or the retailer where you bought the product.
Standard
Test item
Standard
RAD & CON
EN55011(EMI)
Harmonic
EN61000-3-2
Flicker
EN61000-3-3
ESD
IEC 61000-4-2
RS
IEC 61000-4-3
EFT
IEC 61000-4-4
Surge
IEC 61000-4-5
CS
IEC 61000-4-6
PFM
IEC 61000-4-8
DIP
IEC 61000-4-11
EN60601-1-2:2007
5
SAFETY INFORMATION
EMC Information
CAUTION
The DR-17G and DR-22G requires special precautions regarding EMC and need to be installed, put into
service and used according to the following information.
Do not use any cables other than the cables that provided or specified by us. Using other cables may cause
the increase of emission or decrease of immunity.
Do not put any portable and mobile RF communications equipment close to the DR-17G and DR-22G. Doing
so may affect the DR-17G and DR-22G.
The DR-17G and DR-22G should not be used adjacent to or stacked with other equipment. If adjacent or
stacked use is necessary, the equipment or system should be observed to verify normal operation in the
configuration in which it will be used.
Anyone who connects additional equipment to the signal input part or signal output parts, configuring a
medical system, responsible that the system complies with the requirements of IEC/ EN60601-1-2.
Guidance and manufacturer’s declaration – electromagnetic emissions
The DR-17G and DR-22G is intended for use in the electromagnetic environment specified below. The
customer or the user of the DR-17G and DR-22G should assure that it is used in such an environment.
Not Life-supporting Medical Equipment.
Emissions test
Compliance
RF emissions
CISPR11/EN55011
Group 1
RF emissions
CISPR11/EN55011
Class B
Harmonic emissions
IEC/EN61000-3-2
Class A
Voltage fluctuations /
flicker emissions
IEC/EN61000-3-3
Class A
Electromagnetic environment – guidance
The DR-17G and DR-22G uses RF energy only for its
internal function. Therefore, its RF emission are very
low and are not likely to cause any interference in
nearby electronic equipment.
The DR-17G and DR-22G is suitable for use in all
establishments, including domestic establishments
and those directly connected to the public low-voltage
power supply network that supplies buildings used for
domestic purposes.
6
SAFETY INFORMATION
Guidance and manufacturer’s declaration – electromagnetic immunity
The DR-17G and DR-22G is intended for use in the electromagnetic environment specified below. The
customer or the user of the DR-17G and DR-22G should assure that it is used in such an environment.
Not Life-supporting Medical Equipment.
Immunity test
Electrostatic
discharge (ESD)
IEC/EN61000-4-2
Electrical fast
transient / burst
IEC/EN61000-4-4
Surge
IEC/EN61000-4-5
IEC/EN60601
test level
Compliance level
±8 kV contact
±8 kV contact
±15 kV air
±15 kV air
±2 kV for power supply
lines
±2 kV for power supply
lines
±1 kV for input/output
lines
±1 kV for input/output
lines
For power supply lines:
For power supply lines:
± 1 kV line(s) to line(s)
± 1 kV line(s) to line(s)
± 2 kV line(s) to earth
± 2 kV line(s) to earth
Electromagnetic environment –
guidance
Floors should be wood, concrete
or ceramic tile. If floors are covered
with synthetic material, the relative
humidity should be at least 30%.
Mains power quality should be that
of a typical commercial or hospital
environment.
Mains power quality should be that
of a typical commercial or hospital
environment.
For outdoor signal lines: For outdoor signal lines:
± 2 kV line(s) to earth
± 2 kV line(s) to earth
Mains power quality should be that
of a typical commercial or hospital
Voltage dips, short
environment. If the user of the
0% UT; 0,5 cycle
0% UT; 0,5 cycle
interruptions and
DR-17G and DR-22G requires
0%
UT;
1
cycle
0%
UT;
1
cycle
voltage variations
continued operation during
on power supply
power mains interruptions, it is
70% UT; 25/30 cycles
70% UT; 25/30 cycles
input lines
recommended that the DR-17G
<5% UT; 250/300 cycles <5% UT; 250/300 cycles
IEC 61000-4-11
and DR-22G be powered from an
uninterruptible power supply or a
battery.
Power frequency
(50/60Hz)
magnetic field
IEC/EN61000-4-8
3A/m
Power frequency magnetic
fields should be at levels
characteristic of a typical location
in a typical commercial or hospital
environment.
3A/m
NOTE: UT is the a.c. mains voltage prior to application of the test level.
Mains power quality should be that of a typical commercial or hospital environment. If the user of the DR-17G
and DR-22G requires continued operation during power mains interruptions, it is recommended that the
DR-17G and DR-22G be powered from an uninterruptible power supply or a battery.
7
SAFETY INFORMATION
Guidance and manufacturer’s declaration – electromagnetic immunity
The DR-17G and DR-22G is intended for use in the electromagnetic environment specified below. The
customer or the user of the DR-17G and DR-22G should assure that it is used in such an environment.
Not Life-supporting Medical Equipment.
Immunity test
IEC/EN60601
test level
Compliance level
Electromagnetic environment –
guidance
Portable and mobile RF
communications equipment should
be used no closer to any part of the
DR-17G and DR-22G, including
cables, than the recommended
separation distance calculated
from the equation applicable to the
frequency of the transmitter.
Recommended Separation distance
d = 1.2 √ P d = 1.2 √ P, 80MHz to
800MHz
d = 2.3 √ P, 800MHz to 2.5GHz
Conducted RF
IEC/EN61000-4-6
3Vrms
150kHz to 80MHz
3Vrms 3V/m
Radiated RF
IEC/EN61000-4-3
3V/m
80MHz to 2.5GHz
Where “P”is the maximum output
power rating of the transmitter in
watts (W) according to the transmitter
manufacturer and “d” is the
recommended separation distance in
meters (m).
Field strengths from fixed RF
transmitters, as determined by an
electromagnetic site survey:
a. should be less than the
compliance level in each
frequency range
b. Interference may occur in the
vicinity of equipment marked with
the following symbol
NOTE 1 At 80 MHz and 800 MHz, the higher frequency range applies.
NOTE 2 These guidelines may not apply in all situations. Electromagnetic propagation is affected by
absorption and reflection from structures, objects and people.
Field strengths from fixed transmitters, such as base stations for radio (cellular/cordless) telephones and
land mobile radios, amateur radio, AM and FM radio broadcast and TV broadcast cannot be predicted
theoretically with accuracy. To assess the electromagnetic environment due to fixed RF transmitters, an
electromagnetic site survey should be considered. If the measured field strength in the location in which the
DR-17G and DR-22G is used exceeds the applicable RF compliance level above, the DR-17G and DR-22G
should be observed to verify normal operation. If abnormal performance is observed, additional measures
may be necessary, such as reorienting or relocating the DR-17G and DR-22G.
8
SAFETY INFORMATION
ESD declaration statement
There was flickered disturbance on the screen during the test, but could self-recover after the test.
(This permissive loss of performance was met the specification of EUT.)
DIP declaration statement
The EUT reset during the test, but could self-recover after the test.
(This permissive loss of performance was met the specification of EUT.)
Recommended separation distances between portable and mobile RF communications equipment
and the DR-17G and DR-22G
The DR-17G and DR-22G is intended for use in an electromagnetic environment in which radiated RF
disturbances are controlled. The customer or the user of the DR-17G and DR-22G can help prevent
electromagnetic interference by maintaining a minimum distance between portable and mobile RF
communications equipment (transmitters) and the DR-17G and DR-22G as recommended below, according
to the maximum output power of the communications equipment.
Rated maximum output
power of transmitter (W)
Separation distance according to frequency of transmitter (m)
150kHz to 80MHz
1.2
80MHz to 800MHz
1.2
800MHz to 2.5GHz
2.
0.01
0.12
0.12
0.23
0.1
0.38
0.38
0.73
1
1.2
1.2
2.3
10
3.8
3.8
7.3
100
12
12
23
For transmitters rated at a maximum output power not listed above, the recommended separation distance
“d” in meters (m) can be estimated using the equation applicable to the frequency of the transmitter,
where “P” is the maximum output power rating of the transmitter in watts (W) according to the transmitter
manufacturer.
NOTE 1 At 80 MHz and 800 MHz, the separation distance for the higher frequency range applies.
NOTE 2 These guidelines may not apply in all situations. Electromagnetic propagation is affected by
absorption and reflection from structures, objects and people.
Cable length
Power Cord : Accessory
1.8m
9
PRECAUTIONS
Precautions
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
Symbols used in this manual
This icon indicates the existence of
a potential haza rd that could result
in personal injury or damage to the
product.
ISO 7010-M002: Follow instructions
for use
This icon indicates important
operating and servicing information.
This icon indicates complies with the
93/42/EEC, EN60601-1, EN 606011-2 of related European standards.
IEC 60417-5009 : STAND-BY
IEC 60417-5031 : Direct Current
IEC 60417-5032: Alternating Current
IEC 60417-5021: Equipotentiality
Notice
• Read this User Manual carefully before using the LCD display and ke ep it for future reference.
• The product specifications and other information provided in this User Manual are for reference only. All
information is subject to change without notice. Updated content can be downloaded from our web site at
displays.agneovo.com.
• To register online, go to displays.agneovo.com.
• To protect your rights as a consumer, do not remove any sticke rs from the LCD display. Doing so may
affect the determination of the warranty period.
10
PRECAUTIONS
Cautions When Setting Up
Do not place the LCD display near heat sources, such as a heater, exhaust vent, or in direct
sunlight.
Do not cover or block the ventilation holes in the housing.
Place the LCD display on a stable area. Do not place the LCD display where it may subject
to vibration or shock.
Place the LCD display in a well-ventilated area.
Do not place the LCD display outdoors.
Do not place the LCD display in a dusty or humid environment.
Do not spill liquid or insert sharp objects into the LCD display through the ventilation holes.
Doing so may cause accidental fire, electric shock or damage the CD display.
11
PRECAUTIONS
Cautions When Using
Use only the power cord supplied with the LCD
display.
The power outlet should be installed near the LCD
Warning:
display and be easily accessible.
Unplug the power cord
If an extension cord is used with the LCD display,
from the power outlet and
ensure that the total current consumption plugged
into the power outlet does not exceed the ampere
rating.
refer to qualified service
personnel under the following
conditions:
Do not allow anything to rest on the power cord. Do
not place the LCD display where the power cord
♦
When the power cord is
damaged.
may be stepped on.
If the CD display will not be used for an indefinite
♦
If the LCD display has been
period of time, unplug the power cord from the
dropped or the housing has
power outlet.
been damaged.
To disconnect the power cord, grasp and pull by the
plug head. Do not tug on the cord; doing so may
♦
If the LCD display emits smoke
or a distinct odor.
cause fire or electric shock.
The mains plug or appliance coupler is used as
the disconnect device, the disconnect device
shall remain readily operable. Always completely
disconnect the power cord set from your product
whenever you are worki ng or cleaning on it. Do not
Warning:
make connections while the power is on, because
a sudden rush of power can damage sensitive
Ceiling mount or mount
on any other horizo ntal
electronic components.
Do not unplug or touch the power cord with wet
hands.
surface overhead are not
advisable.
Installation in contravention of
the instructions may result in
undesirable consequences,
particularly hurting people and
damaging property. Users who
have already mounted the
display on the ceiling or any
other horizo ntal surface overhead
are strongly advised to contact
AG Neovo for consultations and
solutions to help ensure a most
pleasurable and fulfilling display
experience.
12
PRECAUTIONS
Cleaning and Maintenance
Disconnect this equipment from any AC outlet before cleaning. Do not use liquid or spray detergents for
cleaning. Use a damp cloth. Keeping to clean your monitor by monthly.
The LCD display comes with NeoVTM Optical Glass. Use a soft cloth to clean the glass surface
and the housing. The display can be cleaned using a cloth moistened with 95% ethyl alcohol.
Do not rub or tap the surface of the glass with sharp or abrasive items such as a pen or
screwdriver. This may result in scratching the surface of the glass.
Do not attempt to service the CD display yourself, refer to qualified service personnel.
Opening or removing the covers may expose you to dangerous voltage or other risks.
Notice for the LCD Display
In order to maintain the stable luminous performance, it is recommended to use low brightness setting.
Due to the lifespan of the lamp, it is normal that the brightness quality of the LCD display may decrease
with time.
When static images are displayed for long periods of time, the image may cause an imprint on the LCD
display. This is called image retention or burn-in.
To prevent image retention, do any of the following:
• Set the LCD display to turn off after a few minutes of being idle.
• Use a screen saver that has moving graphics or a blank white image.
• Switch deskt op backg rounds regularly.
• Adjust the LCD display to low brightness settings.
• Turn off the LCD display when the system is not in use.
Things to do when the LCD display shows image retention:
• Turn off the LCD display for extended periods of time. It can be several hours or several days.
• Use a screen saver and run it for extended periods of time.
• Use a black and white image and run it for extended periods of time.
When the LCD display is moved from one room to another or there is a sudden change from low to high
ambient temperature, dew condensation may form on or inside the glass surface. When this happens, do
not turn on the LCD display until the dew disappears.
Due to humid weather conditions, it is normal for mist to form inside the glass surface of the LCD display.
The mist will disappear after a few days or as soon as the weather stabiliz
e s.
There are millions of micro transistors inside the LCD display. It is normal for a few transistors to be
damaged and to produce spots. This is acceptable and is not considered a failure.
The intended use of the DR-17G, DR-22G is to serve as a LCD monitor for integration with the hospital
system.It is designed for general purpose for adults using at hospital environment,continuous operation. For
displaying and viewing of images for reference. The use of this device does not require any direct contact
with patients. It shall not be used for diagnostic purpose nor for life supporting system.
13
PRECAUTIONS
Notice for the LCD Display
Accessory equipment connected to the analog and digital interfaces must be in compliance with the
respective nationally harmonize d IEC standards (i.e. IEC 60950 for data processing equipment, IEC 60065
for video equipment, IEC 61010-1 for laboratory equipment, and IEC 60601-1 for medical equipment).
Furthermore all configurations shall comply with the system standard IEC 60601-1. Everybody who
connects additional equipment to the signal input part or signal output part configures a medical system,
and is therefore, responsible that the system complies with the requirements of the system standard
IEC 60601-1. The unit is for exclusive interconnection with IEC 60601-1 certified equipment in the patient
environment and IEC 60
certified equipment outside of the patient environment. If in doubt, consult the
technical services department or your local representative.
Grounding reliability can only be achieved when the equipment is connected to an equivalent receptacle
marke d “Hospital Only” or “Hospital Grade”.
Use a power cord that matches the voltage of the power outlet, which has been approved and complies
with the safety standard of your particular country.
The single device output analog signals through ADC element (Analog DigitalConvert) conversion to
become a digital signal and the video signal is via Video Decorder conversion. It has become the same
digital signal, these signals via Scaler IC as zoom in or out action and digital image processing, then
through the cable line transmission LVDS signals to one of the LCD module. The last by the clock controller
(Timing Controller, TCON), the clock signal is transmitted to the drive IC on the panel and turn on Backl ight
for LCD module light source by Scaler control.
WARNING – No protection against the ingress of water : IPX0
WARNING – Do not modify this equipment without authoriza tion of the manufacturer.
Installation and OSD adjusting should only be carried by manufacturer trained and authorize d personnel.
WARNING – To avoid risk of electric shock, this equipment must only be connected to a supply mains with
protective earth.
CAUTION: This adapter Manufacturer/model is a forming part of the medical device.
Power by class I power supply.
Adapter manufacturer/model
ADAPTER TECH: ATM065T-P240
Input/output: 100-240V~50-60Hz, 24V(
) 2.71A.
WARNING: Use suitable mounting apparatus to avoid risk of injury.
WARNING The equipment not suitable for use in the presence of a flammable anesthetic mixture with air
or with oxygen or nitrous: Not AP or APG Category
CAUTION: No applied part.
Make sure the user not to contact SIP/SOPs and the patient at the same time.
CAUTION Transport should only be undertaken in a flat surface.
14
CHAPTER 1: PRODUCT DESCRIPTION
Chapter 1: Product Description
1.1 Package Contents
When unpacki ng, check if the following items are included in
the packa ge. If any of them is missing or damaged, contact your
dealer.
LCD Display
DR-17G
Quick Start Guide
DR-22G
Power adapter
Note:
Must use only the supplied power
adapter:
♦ ADAPTER TECH
Model no.: ATM065T-P240
Rating: 24V/2.71A
DR-17G & DR-22G
Quick Start Guide
DR-17G & DR-22G LCD Monitor
DR-17G/DR-22G_Quick Guide_V010
displays.agneovo.com
Power cord
VGA cable
Audio cable
Warranty card
Note:
♦
The pictures are for reference
only. Actual items may vary
upon shipment.
15
PRODUCT DESCRIPTION
1.2 Wall Mounting Installation Preparation
Note:
1.2.1
To protect the glass panel, place a
Wall Mounting
towel or soft cloth before laying the
1
Remove the base stand.
LCD display down.
See procedures below.
2
Wall mount the LCD display.
Screw the mounting bracke t to the VESA holes at
the rear of the LCD display.
Warning:
Ceiling mount or mount
100mm
on any other horizo ntal
surface overhead are not
advisable.
Installation in contravention of
the instructions may result in
100mm
75mm
undesirable consequences,
particularly hurting people and
damaging property. Users who
have already mounted the
75mm
display on the ceiling or any
other horizo ntal surface overhead
are strongly advised to contact
DR-17G
AG Neovo for consultations and
solutions to help ensure a most
100mm
pleasurable and fulfilling display
experience.
Note:
100mm
75mm
Take measures to prevent the
LCD display from falling down
and lessen possible injury and
damage to the display in case of
75mm
earthquake s or other disasters.
♦
DR-22G
Use only the 75 x 75 mm and
100 x 100 mm wall mount ki t
recommended by AG Neovo.
♦
Secure the LCD display on a
solid wall strong enough to bear
its weight.
16
PRODUCT DESCRIPTION
1.2.2
1
2
Removing the Base Stand
ay the CD display face down on a flat even surface.
Remove the screws* securing the base stand from the LCD
display.
3
Detach the base stand.
DR-17G
DR-22G
17
Note:
(*) The screw size is M4 x 10mm.
PRODUCT DESCRIPTION
1.3 LCD Display Overview
1.3.1
Front View and Keypad Buttons
7
6
4
5
2
3
DR-17G
1
8
1
2
3
4
5
DR-22G
18
6
7
8
PRODUCT DESCRIPTION
1
AUTO
Hot Key: Auto Adjustment/Rotate
• For VGA input signal source, press to
perform auto adjustment.
• Press for 3 seconds to enable the Rotate
function.
• When OSD menu is ON, press to close the
OSD menu or exit a submenu.
2
LEFT
Hot Key: Audio Volume Adjustment
• Press to display the volume bar. Then press
the LEFT ke y to decrease the volume.
• When OSD menu is ON, press to select an
option or adjust the settings.
3
RIGHT
Hot Key: Screen Freeze
• Press to activate the screen freeze function.
To deactivate, press any ke y except for the
Power ke y.
• When the volume bar appears, press to
increase the volume.
• When OSD menu is ON, press to select
and option, adjust the settings, or enter the
submenu.
19
4
UP
Hot Key: PIP/PBP Select
• Press repeatedly to select PIP/PBP option
(PIP
P P
FF).
• When OSD menu is ON, press to select an
option or adjust the settings.
5
DOWN
Hot Key: PICTURE MODE Select
• Press repeatedly to select PICTURE MODE
option ( tandard
VIDE ).
• When OSD menu is ON, press to select an
option or adjust the settings.
• When PIP is ON, press to swap the PIP
main and sub picture.
6
MENU
Press to display/hide the OSD menu.
7
SOURCE
Press to select the input signal source.
8
POWER and LED Indicator
• Press to turn the power on or off.
• Indicate the operating status of the LCD
display:
- Lights Green when the LCD display is
turned on.
- Lights Amber when the LCD display is in
standby mode.
- Lights Off when the LCD display is turned
off.
PRODUCT DESCRIPTION
1.3.2
Rear View
S-VIDEO
DR-17G
7
DR-22G
COMPOSITE-1
IN
8
OUT
9
COMPOSITE-2
IN
8
OUT
9
AUDIO
L
10
IN
R
14
14
AUDIO
L
11
OUT
R
DC IN
DVI
HDMI DisplayPort
VGA
AUDIO IN
USB (SERVICE)
12
RS232
13
1
2
3
4
5
6
1
DC IN
Connect with the supplied power adaptor.
8
COMPOSITE-1/COMPOSITE-2 IN
Connect Composite (CVBS) signals input.
2
DVI
Connect DVI signals input.
9
COMPOSITE-1/COMPOSITE-2 OUT
Connect Composite (CVBS) signals output.
3
HDMI
Connect HDMI signals input.
10 AUDIO IN
Connect audio signals input (RCA Stereo
Audio Ja ck) .
4
DisplayPort
Connect DisplayPort signals input.
5
VGA
Connect VGA signals input.
6
7
11 AUDIO OUT
Connect audio signals output (RCA Stereo
Audio Ja ck) .
12 USB (SERVICE)
Connect USB 2.0 for service.
AUDIO IN
Connect audio signals input (3.5 mm Stereo
Audio Ja ck).
13 RS232
Connect RS232 input from external
equipment.
S-VIDEO
Connect S-Video signals input.
14 GROUNDING STUD
Connect to a proper earth ground.
20
CHAPTER 2: MAKING CONNECTIONS
Chapter 2: Making Connections
2.1 Connecting the Power
1
Connect the power cord to the power adapter.
2
Connect the power adapter to the DC power input at the rear of the LCD display.
3
Connect the power cord plug to a power outlet or a power supply.
DC IN
Note:
Caution:
♦
♦
When removing the power supply,
Make sure that the LCD display is
please make sure the plug is
not connected to the power outlet
unlocked.
before maki ng any connections.
Connecting cables while the power
is ON may cause electric shock or
personal injury.
Caution:
♦
When unplugging the power cord,
hold the power cord by the plug
head. Never pull by the cord.
21
MAKING CONNECTIONS
2.2 Connecting Input Source Signals
2.2.1
Connecting a Computer
Using VGA Cables
Connect one end of a VGA cable to the VGA connector of the LCD display and the other end to the VGA
connector of the computer.
VGA
Using DVI Cables
Connect one end of a DVI (DVI-D) cable to the DVI connector of the LCD display and the other end to the DVI
connector of the computer.
DVI
22
MAKING CONNECTIONS
Using HDMI Cables
Connect one end of an HDMI cable to the HDMI connector of the LCD display and the other end to the HDMI
connector of the computer.
HDMI
Using DisplayPort Cables
Connect one end of a DisplayPort cable to the DisplayPort connector of the LCD display and the other end to
the DisplayPort connector of the computer.
DisplayPort
23
MAKING CONNECTIONS
Using RS232 Cables
Connect one end of an RS232 cable to the RS232 connector of the LCD display and the other end to the
RS232 connector of the computer.
RS232
Using Audio Cables
Connect one end of an audio cable to the AUDIO IN connector at the rear of the LCD display and the other
end to the audio out connector of the computer.
AUDIO IN
24
MAKING CONNECTIONS
2.2.2
Connecting a Video Device
Using Composite (CVBS) Cables
Connect one end of a Composite (CVBS) cable to the COMPOSITE 1 / COMPOSITE 2 IN connector of the
LCD display and the other end to the Composite (CVBS) connectors of your device.
For audio input, connect an RCA cable to the AUDIO IN connectors of the LCD display and the audio out
connector of your device.
For video looping, connect one end of a Composite (CVBS) cable to the COMPOSITE 1 / COMPOSITE 2
OUT connector of the LCD display and the other end to the COMPOSITE 1 / COMPOSITE 2 IN connector of
the additional display.
COMPOSITE-1
IN
OUT
COMPOSITE-2
IN
OUT
COMPOSITE-1
IN
AUDIO
L
COMPOSITE-2
IN
IN
R
AUDIO
AUDIO
L
L
IN
OUT
R
R
or
25
MAKING CONNECTIONS
Using S-Video Cables
Connect one end of an S-Video cable to the S-VIDEO connector of the LCD display and the other end to the
S-VIDEO connector of your device.
For audio input, connect an RCA cable to the AUDIO IN connectors of the LCD display and the audio out
connector of your device.
S-VIDEO
AUDIO
L
IN
R
Using HDMI Cables
Connect one end of an HDMI cable to the HDMI connector of the LCD display and the other end to the HDMI
connector of your device.
HDMI
26
MAKING CONNECTIONS
Using DisplayPort Cables
Connect one end of a DisplayPort cable to the DisplayPort connector of the LCD display and the other end to
the DisplayPort connector of your device.
DisplayPort
27
CHAPTER 3: USING THE LCD DISPLAY
Chapter 3: Using the LCD Display
3.1 Turning on the Power
Note:
♦
POWER button
LED indicator
1
Connect the power cord to the power adapter. Then
connect the power adapter to the DC power input at the
The LCD display still consumes
power as long as the power
cord is connected to the power
outlet. Disconnect the power
cord to completely cut off
power.
rear of the LCD display.
2
Press the POWER button to turn the LCD display on.
The LED indicator turns GREEN.
When the LCD display is turned on, press the POWER
button to turn off the LCD display.
The LED indicator turns off.
3.2 Selecting the Input Source Signal
Notes:
♦
After selecting an input source
signal, the input source signal
message appears on the
screen briefly.
For example, HDMI is selected
the following message is
displayed.
SOURCE button
1
Press the
button to call out the input source menu.
V G A
HDMI
♦
D V I
H D M I
D I S P L AY P O R T
C O M P O S I T E
1
C O M P O S I T E
2
S - V I D E O
2
3
If the selected input source
signal is not connected to the
LCD display or is turned off, the
no signal message is displayed
on the screen.
NO
SIGNAL
Press the p or q button to highlight an input source.
Press the u button to select the input source.
INPUT
♦
If the resolution or the graphics
card of the connected computer
is set too high, the input out of
range message is displayed.
INPUT SIGNAL
OUT OF RANGE
28
USING THE LCD DISPLAY
3.3 Adjusting the Volume / Illuminator Function Hot Key
Hot Key: Audio Volume Adjustment
1
Press the t button to call out the volume bar.
2
Press the u button to increase volume or the t button to decrease volume.
3.3.1
Muting the Audio
Press the u and t buttons simultaneously to mute or unmute the audio.
3.3.2
Illuminator Function Hot Key
Press and hold t and u for 5 seconds to turn the screen completely white to enable you to see the light box
for the x-ray film. To change the screen back to normal display mode, press and hold t and u for 5 seconds
again.
3.4 Choosing Your Preferred Picture Settings
Hot Key: PICTURE MODE Select
Press the q button repeatedly to toggle between the picture modes.
Options are as follows:
•
TA DARD M DE Default settings that suits most environments and types of video.
• VIDE
M DE
ettings adjusted for video.
S TA N D A R D M O D E
VIDEO MODE
29
USING THE LCD DISPLAY
3.5 Using Picture-in-Picture (PIP)
The Picture-in-Picture (PIP) and Picture-by-Picture (PIP) feature allows viewing of more than one input source
signal on the LCD display.
3.5.1
PIP/PBP Options
Hot Key: PIP/PBP Select
Press the p button repeatedly to enable and scroll among the PIP/PBP options. Options are as follows:
• PIP On: The sub source signal is displayed within the main source signal.
• PBP (Picture-by-Picture): The main source and the sub source signals are displayed side by side with
equal display size .
• PIP Off: PIP function is disabled, only the main source signal is displayed.
PIP On
PBP
Note:
♦
The main source and sub
source signals can be set in
PIP Setting, see page 46.
PIP Off
♦
Some input source signal
combinations do not support
PIP. See PIP Compatibility
table on page 47.
30
USING THE LCD DISPLAY
3.5.2
PIP/PBP Swap
The main and the sub source signals set in PIP/PBP Setting can be
easily swapped using the keypad.
Note:
Sub source
Main source
♦
PIP/PBP Swap can only be
executed if PIP is enabled, see
page 46.
Press the q button to swap the main source and the sub source
signals. See illustration below.
Sub source
Main source
3.6 Using FREEZE Function
Hot Key: Screen Freeze
The FREEZE function allows you to freeze the screen image but still
continues real-time playback until the image is unfreeze.
Press the u button to activate screen freeze , the screen freeze
message is displayed on the screen.
Freeze On
You can press any button to deactivate except the POWER button.
31
USING THE LCD DISPLAY
3.7 Using Auto Adjustment Function
Note:
♦
Auto Adjustment function is
available only during VGA input
signals.
♦
Hot Key: Auto Adjustment/Rotate
It is recommended to use the
auto adjustment function when
Auto Adjustment function automatically tunes the LCD display to its
using the LCD display for the
optimal setting, including horizontal position, vertical position, clock,
first time or after a resolution or
and phase.
Press the
frequency change.
button to perform auto adjustment.
♦
It is recommended to perform
the Auto Adjustment function
The message auto adjusting is displayed on the screen.
only when the image (non-
AUTO
ADJUSTING
black) is displayed in full
screen.
During auto adjustment, the screen will slightly shake for a few
seconds.
When the message disappears, auto adjustment is completed.
3.8 Using ROTATE Function
The ROTATE function allows you to rotate the screen image at 180°.
Press the
button for 3 seconds to rotate the picture 180º.
Note:
♦
ROTATE function can only be
executed if PIP is off, see page
46.
After ROTATE
image
After executing ROTATE, press the
button for 3 seconds again to
rotate the picture back to its normal state.
Original screen
image
32
USING THE LCD DISPLAY
3.9 Locking the OSD Menu
ock the
D menu to protect the CD display from unauthorised users or from accidentally pressing the
keypad.
To lock the
D, press and hold the keypad buttons listed below for at least 5 seconds or until the
OSD
LOCK OUT
hen the
message appears.
D is locked, all keypad buttons are inactivated.
Type of OSD Lock
ock all buttons
Lock Operation
Press and hold the u, p, and q
buttons simultaneously for 5 seconds.
Unlock Operation
Do one of the following to unlock
• Press and hold the u, p, and
q buttons simultaneously for 5
seconds or until the OSD menu
appears.
ock all buttons except
the POWER button.
Press and hold the t, p, and q
buttons simultaneously for 5 seconds.
• Press and hold the t, p, and
q buttons simultaneously for 5
seconds or until the OSD menu
appears.
33
CHAPTER 4: ON SCREEN DISPLAY MENU
Chapter 4: On Screen Display Menu
4.1 Using the OSD Menu
Operation
1
Display the main menu screen.
1 9 2 0 x 1 0 8 0
Press the
button.
6 0 H z
B R I G H T N E S S
5 0
BRIGHTNESS
C O N T R A S T
5 0
C O L O U R T E M P.
B A C K L I G H T
6 0
IMAGE SETTING
B L A C K
L E V E L
5 0
ASPECT RATIO
PIP SETTING
ANTI-BURN-IN
OSD SETTING
AUDIO SETTING
SYSTEM 1
SYSTEM 2
ECOSMART SENSOR
INPUT SELECT
LANGUAGE
Navigation Window
INFORMATION
E X I T
2
E N T E R
S E L E C T
1 Press the p or q button.
Select the menu.
1 9 2 0 x 1 0 8 0
6 0 H z
2 Press the u button to enter the
B R I G H T N E S S
5 0
BRIGHTNESS
submenu.
C O N T R A S T
5 0
C O L O U R T E M P.
B A C K L I G H T
6 0
IMAGE SETTING
B L A C K
L E V E L
5 0
ASPECT RATIO
PIP SETTING
ANTI-BURN-IN
OSD SETTING
AUDIO SETTING
SYSTEM 1
SYSTEM 2
ECOSMART SENSOR
INPUT SELECT
LANGUAGE
INFORMATION
E X I T
E N T E R
S E L E C T
34
ON SCREEN DISPLAY MENU
Operation
3
0 x 1 0 8 0
Press the p or q button.
Select the submenu item.
6 0 H z
B R I G H T N E S S
5 0
RIGHTNESS
C O N T R A S T
5 0
O L O U R T E M P.
B A C K L I G H T
6 0
AGE SETTING
B L A C K
L E V E L
5 0
SPECT RATIO
P SETTING
The highlighted item with an orange arrow indicates the active
NTI-BURN-IN
submenu.
SD SETTING
4
Adjust the settings.
Press the t or u button.
5
Exit the submenu.
Press the
UDIO SETTING
YSTEM 1
YSTEM 2
or
button to return to
the previous menu.
COSMART SENSOR
PUT SELECT
ANGUAGE
6
Close the OSD window.
Press the
or
button again.
FORMATION
I T
hen settings are modified, all changes are saved when the user does the following
A D J U S T
S E L E C T
• Proceeds to the another menu.
• Exits the OSD menu.
•
aits for the
D menu to disappear.
Note: Availability of some menu items depend on the input source signal. If the menu is not available, it is
disabled and grayed out.
35
ON SCREEN DISPLAY MENU
4.2 OSD Menu Tree
1 9 2 0 x 1 0 8 0
6 0 H z
B R I G H T N E S S
5 0
BRIGHTNESS
1
C O N T R A S T
2
C O L O U R T E M P.
3
IMAGE SETTING
5 0
B A C K L I G H T
6 0
B L A C K
Main Menu
1. RIGHT E
4
ASPECT RATIO
5
PIP SETTING
6
ANTI-BURN-IN
•
5 0
OSD SETTING
7
AUDIO SETTING
8
SYSTEM 1
9
SYSTEM 2
10
ECOSMART SENSOR
11
INPUT SELECT
12
LANGUAGE
13
INFORMATION
14
Submenu
E N
E X I T
RIGHT E
L E V E L
T E R
Remarks
S E L E C T
See page 39.
• CONTRAST
•
AC
IGHT
• BLACK LEVEL
2. COLOUR TEMP.
• NEUTRAL
• WARM
• COOL
• USER
• AUTO COLOUR
36
See page 41.
ON SCREEN DISPLAY MENU
Main Menu
3. IMAGE ETTI G
Submenu
•
HARP E
•
ATURATI
Remarks
See page 42.
• TI T
• GAMMA
• C
UR RA GE
I E REDUCTI
•
• PICTURE M DE
• H. P
ITI
• V. P
ITI
• PHA E
• CLOCK
4. A PECT RATI
See page 45.
• FULL
• REAL
ATIVE
•
• ZOOM
• OVERSCAN
5. PIP ETTI G
• PIP
See page 46.
• MAI
URCE
• SUB SOURCE
•
U PICTURE I E
•
U PIC. P
.
• SWAP
6. A TI- UR -I
See page 48.
• ENABLE
• I TERVA (H UR )
• MODE
7.
D ETTI G
8. AUDI
ETTI G
• TRANSPARENCY
•
D H. P
ITI
•
D V. P
ITI
•
D TIMER
See page 49.
See page 50.
• VOLUME
• AUDI
• SOURCE
9. SYSTEM 1
• P
ER AVI G
• SOURCE DETECT
• DDC/CI
• BLUE SCREEN
•
IG A I F
• Alink
•
G
• LED
• RESET
37
See page 51.
ON SCREEN DISPLAY MENU
Main Menu
10. SYSTEM 2
Submenu
•
UPER RE
•
VERDRIVE
Remarks
UTI
See page 53.
• DCR
• M
11. ECOSMART SENSOR
IT R ID
See page 54.
• ENABLE
• MODE
• LEVEL
12. I PUT E ECT
• VGA
See page 48.
• DVI
• HDMI
• DI P A P RT
• C MP
ITE 1
• C MP
ITE 2
•
13. A GUAGE
-VIDE
elect the
E
D language
/ FR / DE / E / IT / P / R
/P /C /
NL / 简中 / 繁中
1 . I F RMATI
Displays settings information such as Input,
Resolution, Horizontal Frequency, Vertical
Frequency, Timing Mode, and Firmware
Version.
38
CHAPTER 5: ADJUSTING THE LCD DISPLAY
Chapter 5: Adjusting the LCD Display
5.1 Brightness
1 9 2 0 x 1 0 8 0
6 0 H z
1. Press the
B R I G H T N E S S
5 0
BRIGHTNESS
button to call out the
OSD window.
C O N T R A S T
5 0
C O L O U R T E M P.
B A C K L I G H T
6 0
IMAGE SETTING
B L A C K
2. Select BRIGHTNESS menu, then
press the u button.
L E V E L
5 0
ASPECT RATIO
PIP SETTING
3. Press the p or q button to select an
option.
ANTI-BURN-IN
OSD SETTING
AUDIO SETTING
SYSTEM 1
SYSTEM 2
ECOSMART SENSOR
INPUT SELECT
LANGUAGE
INFORMATION
E X I T
Item
BRIGHTNESS
CONTRAST
BACKLIGHT
A D J U S T
S E L E C T
Function
Operation
Adjusts the luminance of the
screen image.
Adjusts the difference between the
black level and the white level.
Adjusts the luminance of the screen
image.
Press the t or u button to adjust
the
value.
Note: This menu option is not
available if the ECOSMART
SENSOR function is enabled.
BLACK LEVEL
Range
Adjusts the black level of the
screen image. Low brightness
setting make s black colour darke r.
See comparison illustrations on page 40.
39
0 to 100
ADJUSTING THE LCD DISPLAY
Original Setting
High Setting
BRIGHTNESS
CONTRAST
BLACK LEVEL
40
Low Setting
ADJUSTING THE LCD DISPLAY
5.2 Colour Temp.
1 9 2 0 x 1 0 8 0
6 0 H z
1. Press the
N E U T R A L
window.
WA R M
BRIGHTNESS
button to call out the OSD
C O O L
U S E R
C O L O U R T E M P.
IMAGE SETTING
R
1 2 8
G
1 2 8
B
1 2 8
A U T O
ASPECT RATIO
2. Select COLOUR TEMP. menu, then
press the u button.
3. Press the p or q button to select an
C O L O U R
PIP SETTING
option.
ANTI-BURN-IN
OSD SETTING
AUDIO SETTING
SYSTEM 1
SYSTEM 2
ECOSMART SENSOR
INPUT SELECT
LANGUAGE
INFORMATION
E X I T
E N T E R
Item
S E L E C T
Function
Operation
Range
NEUTRAL
Provides several colour settings.
WARM
Press the t or u button
COOL
to select the setting.
USER
AUTO COLOUR
Colour setting can be set to:
• NEUTRAL - commonly used for normal lighting conditions.
• WARM - Applies a reddish tint for warmer colours.
• COOL - Applies a bluish tint for cooler colours.
COLOUR TEMP.
• USER - This allows users to set the colour temperature by adjusting the R, G, B
settings according to one’s preference.
1 Select USER, and press the u button.
2 Press the p or q button to select the colour you want to adjust.
3 Press the t or u button to adjust the values between 0 ~ 255.
• AUTO COLOUR - Operates the white balance and automatically adjusts the colour
settings.
1 Select AUTO COLOUR.
2 Press the u button to activate auto colour.
Note: This menu option is only available if the input source is VGA.
Note: Activate RESET to return the colour to its default setting.
41
ADJUSTING THE LCD DISPLAY
5.3 Image Setting
1 9 2 0 x 1 0 8 0
1. Press the
6 0 H z
S H A R P N E S S
BRIGHTNESS
button to call out the OSD
window.
0
S
CA
O TN UT R
RA
A TS I TO N
5 0
C O L O U R T E M P.
2. Select IMAGE SETTING menu, then
T I N T
press the u button.
5 0
IMAGE SETTING
ASPECT RATIO
G A M M A
2 . 0 2 . 2
PIP SETTING
C O L O U R R A N G E
A U T O
2 . 4
3. Press the p or q button to select an
S
option.
F U L L
ANTI-BURN-IN
L I M I T E D
N O I S E R E D U C T I O N
O F F
OSD SETTING
L O W
M I D
AUDIO SETTING
H I G H
P I C T U R E M O D E
S T A N D A R D
SYSTEM 1
V I D E O
SYSTEM 2
H .
P O S I T I O N
V.
P O S I T I O N
5 0
ECOSMART SENSOR
5 0
INPUT SELECT
P H A S E
5 0
LANGUAGE
C L O C K
INFORMATION
E X I T
5 0
A D J U S T
Item
S E L E C T
Function
Operation
SHARPNESS
Adjusts the clarity and focus of the
screen image.
SATURATION
Adjusts the colour saturation.
TINT
Adjusts the colour tint.
Range
Press the t or u button to
0 to 100
adjust the value.
2.0
Adjusts the non-linear setting for
Press the t or u button to
2.2
picture luminance and contrast.
select the setting.
2.4
OUTPUT
OUTPUT
OUTPUT
OUTPUT
S
GAMMA
INPUT
INPUT
INPUT
INPUT
Display Gamma 2.0
Display Gamma 2.2
Display Gamma 2.4
Display Gamma S
42
ADJUSTING THE LCD DISPLAY
Item
Function
Operation
Range
Adjusts black and white levels for
video.
Press the t or u button to
Note: This menu option is only
available if the input source is HDMI.
select the setting.
AUTO
FULL
LIMITED
Signal source from PC - PC signal at a full range (Grayscale 0-255) state:
COLOUR RANGE
Monitor OSD colour range: Full *Please select
Monitor OSD colour range: Limited
Signal source from Video - Video signal at a limited range (Grayscale 16~235) state:
Monitor OSD colour range: Limited *Please select
Monitor OSD colour range: Full
OFF
Adjusts the noise reduction to help
remove noise from images. This
Press the t or u button to
LOW
helps produce clearer and crisper
select the setting.
MID
HIGH
images.
NOISE
REDUCTION
Noise Reduction Off
PICTURE MODE
Noise Reduction On
elects a predefined picture mode
setting.
Press the t or u button to
select the setting.
43
STANDARD
VIDEO
ADJUSTING THE LCD DISPLAY
Item
Function
Operation
Range
Moves the screen image to the left
H. POSITION
(Horizontal Position) or right.
V. POSITION
(Vertical Position)
Moves the screen image up or down.
Adjusts the phase timing to
synchronise with the video signal.
PHASE
Note: This menu option is only
available if the input source is VGA.
Adjusts the frequency timing to
synchronise with the video signal.
CLOCK
Note: This menu option is only
available if the input source is VGA.
44
Press the t or u button to
adjust the value.
0 to 100
ADJUSTING THE LCD DISPLAY
5.4 Aspect Ratio
1 9 2 0 x 1 0 8 0
6 0 H z
1. Press the
F U L L
window.
R E A L
BRIGHTNESS
button to call out the OSD
N A T I V E
Z O O M
C O L O U R T E M P.
H .
2. Select ASPECT RATIO menu, then
Z O O M
press the u button.
1 0 0
IMAGE SETTING
V.
Z O O M
1 0 0
ASPECT RATIO
O V E R S C A N
PIP SETTING
3. Pressthe p or q button to select an
option.
0
ANTI-BURN-IN
OSD SETTING
AUDIO SETTING
SYSTEM 1
SYSTEM 2
ECOSMART SENSOR
INPUT SELECT
LANGUAGE
INFORMATION
E X I T
A D J U S T
Item
S E L E C T
Function
Operation
Range
FULL
Adjusts the aspect ratio of the screen Press the t or u button to
image.
select the setting.
REAL
NATIVE
ZOOM
OVERSCAN
The aspect ratio setting can be set to:
• FULL - Enlarges the picture to fill the screen.
ASPECT RATIO
• REAL - Displays the picture at its original size .
• NATIVE - Enlarges the picture but retain its original aspect ratio.
• ZOOM - Sets a custom aspect ratio by adjusting the horizo ntal zo om(H. ZOOM)
and /or vertical zo om(V.ZOOM) according to your preference.
1 Select ZOOM, and press the u button.
2 Press the p or q button to select the zo om parameter you want to adjust.
3 Press the t or u button to adjust the values between 0 ~ 100.
• OVERSCAN - Adjusts the overscan setting to fix the cut-off screen edges.
Press the t or u button to adjust the values between 0 ~ 100.
45
ADJUSTING THE LCD DISPLAY
5.5 PIP Setting
1 9 2 0 x 1 0 8 0
6 0 H z
1. Press the
P I P
O F F
BRIGHTNESS
window.
P I P
P B P
C O L O U R T E M P.
2. Select PIP SETTING menu, then press
M A I N S O U R C E
V G A D V I
H D M I
IMAGE SETTING
the u button.
D I S P L A Y P O R T
ASPECT RATIO
C O M P O S I T E
1
C O M P O S I T E
2
3. Press the p or q button to select an
S - V I D E O
PIP SETTING
option.
S U B S O U R C E
V G A D V I
H D M I
ANTI-BURN-IN
button to call out the OSD
D I S P L A Y P O R T
OSD SETTING
C O M P O S I T E
1
C O M P O S I T E
2
S - V I D E O
AUDIO SETTING
S U B
1
SYSTEM 1
P I C T U R E S I Z E
2
3
SYSTEM 2
S U B P I C . P O S .
L + U R + U
ECOSMART SENSOR
S W A P
L + D
R + D
INPUT SELECT
LANGUAGE
INFORMATION
A D J U S T
E X I T
Item
PIP
S E L E C T
Function
Operation
Allows you to select the PIP setting
Press the t or u button to
or disable PIP.
select the value.
Range
OFF
PIP
PBP
PIP can be set to:
• OFF - Disables PIP.
• PIP - The sub source image is within the main source image.
• PBP - The main source and sub source images are displayed side by side.
MAIN SOURCE
Allows you to select the main source
VGA
signal.
DVI
Press the t or u button to
SUB SOURCE
Allows you to select the sub source
signal.
select the setting.
HDMI
DISPLAYPORT
COMPOSITE 1
COMPOSITE 2
S-VIDEO
46
ADJUSTING THE LCD DISPLAY
Note: Any input signal may be set as the main or the sub source signal. However, some input signals are not
supported to be paired together as the main and the sub source signals.
Refer to the following table for compatibility options:
Main Source
Input Source
HDMI DISPLAYPORT COMPOSITE 1
COMPOSITE 2
S-VIDEO
O
O
O
O
O
O
O
X
O
O
O
O
O
X
O
O
O
X
X
X
X
X
X
X
X
VGA
DVI
VGA
X
O
O
O
DVI
O
X
O
HDMI
Sub
DISPLAYPORT
Source
COMPOSITE 1
O
O
O
O
O
O
O
O
COMPOSITE 2
O
O
O
O
S-VIDEO
O
O
O
O
X
Item
Function
Operation
Allows you to select the size of the
sub source image.
Press the t or u button to
select the setting.
SIZE
Note: This menu option is only
available if the PIP setting is to PIP.
(Sub Picture
The size of the sub source image can be set to:
SUB PICTURE
Size )
Range
1
2
3
• 1 - Small image size .
• 2 - Medium image size .
• 3 - Large image size .
Allows you to select the position of
L+U
the sub source image.
Press the t or u button to
R+U
select the setting.
L+D
SUB PIC. POS.
Note: This menu option is only
available if the PIP setting is to PIP
(Sub Picture
The position of the sub source image can be set to:
Position)
R+D
• L+U - Sets the image on the upper left corner of the screen.
• R+U - Sets the image on the upper right corner of the screen.
• L+D - Sets the image on the lower left corner of the screen.
• R+D - Sets the image on the lower right corner of the screen.
SWAP
Swaps the main source and sub
Press the u button to execute
source signals.
the function.
47
-
ADJUSTING THE LCD DISPLAY
5.6 Anti-Burn-in
1 9 2 0 x 1 0 8 0
6 0 H z
1. Press the
BRIGHTNESS
E N A B L E
O N
C O L O U R T E M P.
I N T E R VA L ( H O U R S )
4
5
6
8
IMAGE SETTING
M O D E
A
B
O F F
button to call out the
OSD window.
2. Select ANTI-BURN-IN menu, then
press the u button.
C
3. Press the p or q button to select an
ASPECT RATIO
PIP SETTING
option.
ANTI-BURN-IN
OSD SETTING
AUDIO SETTING
SYSTEM 1
SYSTEM 2
ECOSMART SENSOR
INPUT SELECT
LANGUAGE
INFORMATION
A D J U S T
E X I T
Item
ENABLE
INTERVAL
(HOURS)
S E L E C T
Function
Operation
Enables or disables Anti-Burn-In
function.
Press the t or u button to select
ON
the setting.
OFF
4
Sets the interval time (hour)
between activating the Anti-Burn-In
function.
Press the t or u button to adjust
the value.
5
6
8
Press the t or u button to select
Selects the Anti-Burn-In mode.
MODE
Range
the setting.
Anti-Burn-In mode can be set to:
• A - Executes fast.
• B - Slower but more precise than mode A.
• C - Slowest but the most precise anti-burn-in mode.
48
A
B
C
ADJUSTING THE LCD DISPLAY
5.7 OSD Setting
1 9 2 0 x 1 0 8 0
6 0 H z
1. Press the
T R A N S PA R E N C Y
0
BRIGHTNESS
O S D
H .
P O S I T I O N
O S D
V.
P O S I T I O N
5 0
C O L O U R T E M P.
5 0
IMAGE SETTING
O S D
button to call out the OSD
window.
2. Select OSD SETTING menu, then press
the u button.
T I M E R
ASPECT RATIO
1 5
PIP SETTING
3. Press the p or q button to select an
option.
ANTI-BURN-IN
OSD SETTING
AUDIO SETTING
SYSTEM 1
SYSTEM 2
ECOSMART SENSOR
INPUT SELECT
LANGUAGE
INFORMATION
E X I T
A D J U S T
Item
TRANSPARENCY
OSD H. POSITION
(Horizo ntal
Position)
S E L E C T
Function
Operation
Range
Adjusts the transparency level of the
OSD screen.
Moves the OSD window to the left or
0 to 100
right of the screen.
OSD V. POSITION
Moves the OSD window up or down
(Vertical Position)
the screen.
Press the t or u button to
adjust the value.
Sets the length of time (in seconds)
OSD TIMER
the OSD screen is displayed. When
the time elapses, the OSD screen is
automatically inactivated.
49
5 to 100
ADJUSTING THE LCD DISPLAY
5.8 Audio Setting
1 9 2 0 x 1 0 8 0
6 0 H z
1. Press the
V O L U M E
5 0
BRIGHTNESS
button to call out the OSD
window.
A U D I O
C O L O U R T E M P.
O N
2. Select AUDIO SETTING menu, then
O F F
press the u button.
S O U R C E
IMAGE SETTING
P C
V I D E O
3. Press the p or q button to select an
ASPECT RATIO
PIP SETTING
option.
ANTI-BURN-IN
OSD SETTING
AUDIO SETTING
SYSTEM 1
SYSTEM 2
ECOSMART SENSOR
INPUT SELECT
LANGUAGE
INFORMATION
E X I T
A D J U S T
Item
VOLUME
AUDIO
S E L E C T
Function
Operation
Adjusts the volume level of the builtin speake r.
0 to 100
ON
Turns the audio ON or OFF.
OFF
Selects the audio source for the PC
or Video input signal.
SOURCE
Press the t or u button to
adjust the value.
Range
Press the t or u button to
select the setting.
Note: This menu option is only
available if the input source is HDMI
or DisplayPort.
50
PC
VIDEO
ADJUSTING THE LCD DISPLAY
5.9 System 1
1 9 2 0 x 1 0 8 0
6 0 H z
P O W E R
BRIGHTNESS
1. Press the
S AV I N G
O N
S O U R C E
D E T E C T
A U T O
C O L O U R T E M P.
2. Select SYSTEM 1 menu, then press the
M A N U A L
IMAGE SETTING
u button.
D D C / C I
O N
ASPECT RATIO
B L U E
O F F
3. Press the p or q button to select an
S C R E E N
O N
O F F
PIP SETTING
S I G N A L
O N
ANTI-BURN-IN
button to call out the OSD
window.
O F F
option.
I N F O
O F F
A l i n k
O N
OSD SETTING
O F F
L O G O
AUDIO SETTING
O N
O F F
L E D
SYSTEM 1
O N
O F F
R E S E T
SYSTEM 2
ECOSMART SENSOR
INPUT SELECT
LANGUAGE
INFORMATION
E X I T
Item
A D J U S T
S E L E C T
Function
Operation
Range
Enables or disables power saving mode.
When the LCD display turns into power
saving mode, the screen turns black and the
LED indicator lights AMBER.
POWER
SAVING
Note: The amount of time for the display to
enter power saving varies depending on the
SOURCE DETECT setting. If the SOURCE
ON
DETECT is set to AUTO, the display checks
Press the t or u button to
all input source signals before entering
select the setting.
OFF
power saving mode if no signal is detected;
this take s up more time. If the SOURCE
DETECT is set to MANUAL, the display
enters power saving mode right away.
SOURCE
DETECT
Sets the display to automatically or manually
detect the input source signal.
51
AUTO
MANUAL
ADJUSTING THE LCD DISPLAY
Item
Function
Operation
Range
Press the t or u button to
ON
select the setting.
OFF
Activates the DDC/CI protocol to allow users
DDC/CI
to configure the monitor by a software using
two wires on the VGA, HDMI, DisplayPort, or
DVI cables.
BLUE
SCREEN
SIGNAL INFO
Enables or disables the blue screen feature.
If the setting is set to ON, it displays a blue
screen when no signal is available.
Enables or disables the signal information to
be displayed on the screen.
Enables or disables HDMI Consumer
Electronics Control control.
If the setting is set to On, you can control the
Alink
connected HDMI-CEC compatible device on
the same power on or power off status.
Note: This menu option is only available if
the input source is HDMI.
Enables or disables the logo feature.
LOGO
If the setting is set to ON, the AG Neovo
logo is briefly displayed after the display is
powered on.
LED
RESET
Sets the display LED indicator on or off.
Use to reset all to default settings, except
Press the u button to
Language, and the input source.
execute the function.
52
-
ADJUSTING THE LCD DISPLAY
5.10 System 2
1 9 2 0 x 1 0 8 0
6 0 H z
S U P E R
1. Press the
R E S O L U T I O N
BRIGHTNESS
button to call out the OSD
window.
O F F
L O W
M I D
C O L O U R T E M P.
2. Select SYSTEM 2 menu, then press the
H I G H
IMAGE SETTING
u button.
O V E R D R I V E
O F F
ASPECT RATIO
3. Press the p or q button to select an
L O W
M I D
PIP SETTING
option.
H I G H
D C R
ANTI-BURN-IN
O N
M O N I T O R
OSD SETTING
O F F
I D
1
AUDIO SETTING
SYSTEM 1
SYSTEM 2
ECOSMART SENSOR
INPUT SELECT
LANGUAGE
INFORMATION
E X I T
Item
A D J U S T
S E L E C T
Function
Operation
Range
SUPER
Upscales images at a higher and more
OFF
RESOLUTION
detailed resolution for better clearness.
LOW
OVERDRIVE
Enhances the display response time.
MID
HIGH
Activates DCR. This feature provides
automatic adjustment of picture brightness
and contrast at high speed and dynamic
DCR
contrast range, such as when watching
(Dynamic
movies. DCR is suitable for indoor viewing.
Contrast Ratio)
Note: When the DCR function is activated,
the BACKLIGHT and ECOSMART SENSOR
function will be disabled.
Press the t or u button to
select the setting.
ON
OFF
Sets the ID number for controlling the
MONITOR ID
display via the RS232 connection. Each
Press the t or u button to
display must have a unique ID number when
set the ID.
multiple sets of this display are connected.
53
1~255
ADJUSTING THE LCD DISPLAY
5.11 EcoSmart Sensor
With the built-in EcoSmart sensor, users can enable the Eco Smart feature to automatically adjust the LCD
screen brightness according to the ambient light. This feature comforts the eyes and helps optimise energy
efficiency.
Note: Please make sure the EcoSmart sensor is not covered when enabling this function.
EcoSmart
sensor
EcoSmart
sensor
DR-17G
1 9 2 0 x 1 0 8 0
6 0 H z
1. Press the
E N A B L E
O N
BRIGHTNESS
DR-22G
button to call out the OSD
window.
O F F
M O D E
A U T O
C O L O U R T E M P.
2. Select ECOSMART SENSOR menu,
U S E R
IMAGE SETTING
then press the u button.
L E V E L
8 0
3. Press the p or q button to select an
ASPECT RATIO
PIP SETTING
option.
ANTI-BURN-IN
OSD SETTING
AUDIO SETTING
SYSTEM 1
SYSTEM 2
ECOSMART SENSOR
INPUT SELECT
LANGUAGE
INFORMATION
E X I T
A D J U S T
S E L E C T
54
ADJUSTING THE LCD DISPLAY
Item
ENABLE
Function
Operation
Enables or disables the Eco Smart
Press the t or u button to
ON
feature.
select the setting.
OFF
Sets the auto brightness mode.
MODE
Value
Press the t or u button to
AUTO
select the setting.
USER
The mode can be set to:
• AUTO - This mode is the default mode. The LCD brightness automatically adjusts
to the ambient brightness.
• USER - Allows you to manually adjust the LCD brightness.
Allows you to set the level of LCD
brightness.
LEVEL
Note: This menu option is only
available if the MODE setting is to
USER.
55
Press the t or u button to
adjust the value.
0 to 100
ADJUSTING THE LCD DISPLAY
5.12 Input Select
1 9 2 0 x 1 0 8 0
6 0 H z
1. Press the
V G A
button to call out the OSD
window.
D V I
BRIGHTNESS
H D M I
D I S P L AY P O R T
C O L O U R T E M P.
IMAGE SETTING
C O M P O S I T E
1
C O M P O S I T E
2
2. Select INPUT SELECT menu, then press
the u button.
S - V I D E O
3. Press the p or q button to select an
ASPECT RATIO
PIP SETTING
option.
ANTI-BURN-IN
OSD SETTING
AUDIO SETTING
SYSTEM 1
SYSTEM 2
ECOSMART SENSOR
INPUT SELECT
LANGUAGE
INFORMATION
E X I T
E N T E R
Item
S E L E C T
Function
Operation
VGA
Sets VGA as the input source signal.
DVI
Sets DVI as the input source signal.
HDMI
DISPLAYPORT
COMPOSITE 1
COMPOSITE 2
S-VIDEO
Value
Sets HDMI as the input source
signal.
Sets DisplayPort as the input source
signal.
Press the u button to switch to
Sets COMPOSITE 1 as the input
the selected input source.
source signal.
Sets COMPOSITE 2 as the input
source signal.
Sets S-VIDEO as the input source
signal.
56
-
CHAPTER 6: APPENDIX
Chapter 6: Appendix
6.1 Warning Messages
Warning Messages
Cause
The resolution or the refresh rate of
INPUT SIGNAL
OUT OF RANGE
Solution
• Change the resolution or the
the graphics card of the computer
refresh rate of the graphics
is set too high.
card.
The LCD display cannot detect the
input source signal.
• Check if the input source is
turned ON.
• Check if the signal cable is
NO
SIGNAL
properly connected.
• Check if any pin inside the
cable connector is twisted or
broke n.
OSD
LOCK OUT
ANTI-BURN-IN
ON
ANTI-BURN-IN
OFF
The OSD has been locke d by the
user.
• Unlock the OSD. Refer to page
33.
The Anti-Burn-In function has been
enabled by the user.
The Anti-Burn-In function has been
disabled by the user.
57
• Disable the Anti-Burn-In
function. Refer to page 48.
• Enable the Anti-Burn-In
function. Refer to page 48.
APPENDIX
6.2 Supported Resolutions
PC Mode
Resolution
Refresh Rate
Horizontal
Vertical
IBM VGA
720
400
70
IBM VGA
640
480
60
Apple Mac II
640
480
67
VESA
640
480
72
VESA
640
480
75
VESA
800
600
56
VESA
800
600
60
VESA
800
600
72
VESA
800
600
75
Apple Mac II
832
624
75
VESA
1024
768
60
VESA
1024
768
70
VESA
1024
768
75
VESA
1280
1024
60
VESA
1280
1024
75
Apple Mac II
1152
870
75
VESA
1152
864
75
VESA
1280
800
60
VESA
1280
800
75
VESA
1280
960
60
VESA
1440
900
60
VESA
1680
1050
60
VESA
1920
1080
60
Video Mode
Resolution
Refresh Rate
Horizontal
Vertical
EDTV
720
480
60i
EDTV
720
480
60
EDTV
720
576
50i
EDTV
720
576
50
HDTV
1280
720
50
EDTV
1280
720
60
HDTV
1920
1080
50i
HDTV
1920
1080
50
HDTV
1920
1080
60i
58
APPENDIX
Video Mode
Resolution
Refresh Rate
Horizontal
Vertical
HDTV
1920
1080
60
HDTV
1920
1080
24
HDTV
1920
1080
25
HDTV
1920
1080
30
6.3 Troubleshooting
Problem
No picture.
• LED indicator is OFF.
Possible Cause and Solution
• Check if the LCD display is turned ON.
• Check if the power cord is properly connected to the LCD display.
• Check if the power cord is plugged into the power outlet.
• LED indicator is
AMBER.
• Check if the computer is turned ON.
• Check if the computer is in standby mode, move the mouse or press
any ke y to wake up the computer.
Image position is incorrect.
• Adjust the H. POSITION and V. POSITION values. See IMAGE
SETTING on page 42.
The displayed texts are
blurry.
• For VGA input, press the
button on the ke ypad to auto-adjust the
display.
• Adjust the IMAGE SETTING (see page 42).
The OSD menu can’t be
• The OSD is locke d. To unlock the OSD, see page 33.
called out.
Red, blue, green, white
dots appear on screen.
• There are millions of micro transistors inside the LCD display. It is
normal for a few transistors to be damaged and to produce spots. This
is acceptable and is not considered a failure.
No audio output.
• Check if the volume is set to 0 (see page 29 or 50).
• Check if the AUDIO SETTING > AUDIO setting is set to OFF (see page
50).
• For VGA or DVI input, check the audio setting of the computer.
• For HDMI or DisplayPort input, select the correct audio input source
(see page 50).
PIP mode does not work.
• The main and sub input source signals are not compatible to be
displayed together in PIP mode. Check the PIP Compatibility Table for
details (see page 47).
59
APPENDIX
Problem
Cannot adjust the backl ight
setting.
Possible Cause and Solution
• The Eco Smart feature is enabled. Set the ECOSMART SENSOR >
ENABLE setting to OFF to disable the Eco Smart feature (see page
54).
The displayed picture looks
• Adjust the aspect ratio (see page 45).
distorted.
Dew formed on or inside
the LCD display.
• This normally happens when the LCD display is moved a cold room to
a hot room temperature. Do not turn ON the LCD display, wait for the
dew condensation to disappear.
Mist formed inside the
glass surface.
• This happens due to humid weather conditions. This is a normal
occurrence. The mist will disappear after a few days or as soon as the
weather stabilize s.
Faint shadows from a
static image appear on the
screen.
• Turn off the LCD display for extended periods of time.
• Use a screen saver or a black and white image and run it for extended
periods of time.
60
APPENDIX
6.4 Transporting the LCD Display
To transport the LCD display for repair or shipment, place the display in its original packa ging carton.
1
Place the two foam cushions on each side of the LCD display for protection.
2
Place the LCD display down in the box.
3
Place the accessories box on the designated area (if necessary).
4
Close and tape the box.
61
CHAPTER 7: SPECIFICATIONS
Chapter 7: Specifications
7.1 Display Specifications
DR-17G
Panel
Panel Type
LED-Backl it TFT LCD (TN Technology)
DR-22G
LED-Backl it TFT LCD (TN Technology)
Panel Size
17.0"
21.5"
Max. Resolution
SXGA 1280 x 1024
FHD 1920 x 1080
Pixel Pitch
0.264 mm
0.248 mm
Brightness
250 cd/m²
250 cd/m²
Contrast Ratio
20,000,000:1 (DCR)
20,000,000:1 (DCR)
Viewing Angle (H/V)
170°/160°
170°/160°
Display Colour
16.7M
16.7M
Response Time
3 ms
3 ms
Frequency (H/V)
H Freq.
24 kHz- 83 kH z
24 kH z- 83 kH z
V Freq.
50 Hz- 75 Hz
50 Hz- 75 Hz
Input
DisplayPort
x1
x1
Output
HDMI
1.4 x 1
1.4 x 1
DVI
24-Pin DVI-D x 1
24-Pin DVI-D x 1
VGA
15-Pin D-Sub x 1
15-Pin D-Sub x 1
Composite (CVBS)
BNC x 2
BNC x 2
S-Video
4-Pin mini DIN x 1
4-Pin mini DIN x 1
Composite (CVBS)
BNC x 2
BNC x 2
External Control
RS232 In
2.5 mm Phone Ja ck
2.5 mm Phone Ja ck
Other Connectivity
USB
2.0 x1 (Service Port)
2.0 x1 (Service Port)
Audio
Audio In
Stereo Audio Ja ck (3.5 mm)
Stereo Audio Ja ck (RCA)
Stereo Audio Ja ck (3.5 mm)
Stereo Audio Ja ck (RCA)
Power
Glass
Audio Out
Stereo Audio Ja ck (RCA)
Stereo Audio Ja ck (RCA)
Internal Speake rs
2W x 2
2W x 2
Power Supply
External
External
Power Requirements
DC 24V, 2.71A
DC 24V, 2.71A
On Mode
17W (On)
21W (On)
Stand-by Mode
< 0.7 W
< 0.7 W
Off Mode
< 0.7 W
< 0.7 W
Thickn ess
3.0 mm (0.12")
3.0 mm (0.12")
Reflection Rate
< 1%
< 1%
Transmission Rate
> 97%
> 97%
Hardness
Operating Conditions Temperature
Transport/ Storage
Conditions
> 9H
> 9H
0°C-40°C (32°F-104°F)
0°C-40°C (32°F-104°F)
Humidity
10%-90% (non-condensing)
10%-90% (non-condensing)
Altitude
< 12,000 feet (3,658 m)
< 12,000 feet (3,658 m)
Temperature
-20°C-60°C (-4°F-140°F)
-20°C-60°C (-4°F-140°F)
Humidity
5%-95% (non-condensing)
5%-95% (non-condensing)
Altitude
< 40,000 feet (12,192 m)
< 40,000 feet (12,192 m)
Mounting
VESA FPMPMI
Yes (100 x 100 mm & 75 x 75 mm)
Yes (100 x 100 mm & 75 x 75 mm)
Stand
Tilt
0° to 22°
0° to 17°
Security
Kensington Security Slot
Yes
Yes
Dimensions
w/Base (W x H x D)
409.4 x 398.2 x 175.0 mm
(16.1” x 15.7” x 6.9”)
513.2 x 368.5 x 155.0 mm
(20.2” x 14.5” x 6.1”)
Packa ging (W x H x D)
506.0 x 506.0 x 225.0 mm
(19.9” x 19.9” x 8.9”)
614.0 x 477.0 x 204.0 mm
(24.2” x 18.8” x 8.0”)
Weight
w/Base
6.1 kg (13.4 lb)
6.8 kg (15.0 lb)
Packa ging
8.1 kg (17.9 lb)
9.3 kg (21.0 lb)
Note:
♦
All specifications are subject to change without prior notice.
62
SPECIFICATIONS
7.2 Display Dimensions
64.5
409.4(outline dimension)
340(opening dimension)
149
100
75
149
134.5
(M4xL10) x8
199
75.25
116
183
398.2
75
100
235
167.5
31.25
0°~22°
46.75
350.5
37
29
272.5(opening dimension)
361.9(outline dimension)
29
40.25
61.5
DR-17G Dimensions
31.5
7.2.1
199
175
60
278
60
240
53.5
DR-22G Dimensions
27.4
7.2.2
56.2
513.2(outline dimension)
202.8
505.6
0~17°
32.6
477.8(opening dimension)
100
75
202.8
(M4xL10) x8
117.5
368.5
75
100
217.8
151.4
16.8
30.8
68.5
99.3
165.4
316.7
269.2(opening dimension)
324.3(outline dimension)
30.4
13.9
252.8
252.8
155
111.6
282.4
111.6
227.4
AG Neovo
Company Address: 5F-1, No. 3-1, Park Street, Nangang District, Taipei, 11503, Taiwan.
Copyright © 2019 AG Neovo. All rights reserved.
DR2G00/DR7G00_UM_V010
63
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement