AG Neovo HX-24G User Manual

AG Neovo HX-24G User Manual
HX-24G LCD Monitor
displays.agneovo.com
User Manual
TABLE OF CONTENTS
Safety Information
Federal Communications Commission (FCC) Notice (U.S. Only) ............................................................ 4
WEEE ....................................................................................................................................................... 5
Precautions
Notice ....................................................................................................................................................... 6
Cautions When Setting Up ....................................................................................................................... 6
Cautions When Using............................................................................................................................... 7
Cleaning and Maintenance....................................................................................................................... 7
Notice for the LCD Display ....................................................................................................................... 8
Chapter 1: Product Description
1.1 Package Contents .............................................................................................................................. 9
1.2 Wall Mounting Installation Preparation ............................................................................................... 10
1.2.1
Wall Mounting .......................................................................................................................... 10
1.2.2
Removing the Base Stand....................................................................................................... 11
1.3 LCD Display Overview ....................................................................................................................... 12
1.3.1
Front View and Keypad Buttons .............................................................................................. 12
1.3.2
Rear View ................................................................................................................................ 13
Chapter 2: Making Connections
2.1 Connecting the Power ........................................................................................................................ 14
2.2 Connecting Input Source Signals ....................................................................................................... 15
2.2.1
Connecting a Computer .......................................................................................................... 15
Using VGA Cables ......................................................................................................................... 15
Using DVI Cables ........................................................................................................................... 15
Using HDMI Cables........................................................................................................................ 16
Using DisplayPort Cables .............................................................................................................. 16
Using RS232 Cables ...................................................................................................................... 17
Using Audio Cables ........................................................................................................................ 17
2.2.2
Connecting a Video Device ..................................................................................................... 18
Using Composite (CVBS) Cables .................................................................................................. 18
Using SDI Cables ........................................................................................................................... 18
Using HDMI Cables........................................................................................................................ 19
Using DisplayPort Cables .............................................................................................................. 19
Chapter 3: Using the LCD Display
3.1 Turning on the Power ......................................................................................................................... 20
3.2 Selecting the Input Source Signal ...................................................................................................... 20
3.3 Adjusting the Volume .......................................................................................................................... 21
3.3.1
Muting the Audio...................................................................................................................... 21
3.4 Choosing Your Preferred Picture Settings .......................................................................................... 21
3.5 Using Picture-in-Picture (PIP) ............................................................................................................ 22
3.5.1
PIP/PBP Options ..................................................................................................................... 22
3.5.2
PIP/PBP Swap ........................................................................................................................ 23
3.6 Using FREEZE Function .................................................................................................................... 23
2
TABLE OF CONTENTS
3.7 Using Auto Adjustment Function ........................................................................................................ 24
3.8 Using ROTATE Function .................................................................................................................... 24
3.9 Locking the OSD Menu ...................................................................................................................... 25
Chapter 4: On Screen Display Menu
4.1 Using the OSD Menu ......................................................................................................................... 26
4.2 OSD Menu Tree ................................................................................................................................. 28
Chapter 5: Adjusting the LCD Display
5.1 Brightness .......................................................................................................................................... 31
5.2 Colour Temp. ...................................................................................................................................... 33
5.3 Image Setting ..................................................................................................................................... 34
5.4 Aspect Ratio ....................................................................................................................................... 37
5.5 PIP Setting ......................................................................................................................................... 38
5.6 Anti-Burn-in......................................................................................................................................... 40
5.7 OSD Setting ....................................................................................................................................... 41
5.8 Audio Setting ...................................................................................................................................... 42
5.9 System 1 ............................................................................................................................................ 43
5.10 System 2 .......................................................................................................................................... 45
5.11 EcoSmart Sensor ............................................................................................................................. 46
5.12 Input Select ...................................................................................................................................... 48
Chapter 6: Appendix
6.1 Warning Messages ............................................................................................................................. 49
6.2 Supported Resolutions ....................................................................................................................... 50
6.3 Troubleshooting .................................................................................................................................. 51
6.4 Transporting the LCD Display ............................................................................................................ 53
Chapter 7: Specifications
7.1 Display Specifications ........................................................................................................................ 54
7.2 Display Dimensions ............................................................................................................................ 56
7.2.1
HX-24G Dimensions................................................................................................................ 56
3
SAFETY INFORMATION
Safety Information
Federal Communications Commission (FCC) Notice (U.S. Only)
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
•
Consult the dealer or an experienced radio/TV technician for help.
an es o
o ifications not e p essly app o e
y t e pa ty esponsi le o co pliance co l
void the user’s authority to operate the equipment.
Use only an RF shielded cable that was supplied with the display when connecting this display to a computer
device.
o p e ent a a e
ic
ay es lt in fi e o s oc
a a
o not e pose t is appliance to ain o e cessi e
moisture.
THIS CLASS B DIGITAL APPARATUS MEETS ALL REQUIREMENTS OF THE CANADIAN INTERFERENCECAUSING EQUIPMENT REGULATIONS.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
4
SAFETY INFORMATION
WEEE
Information for users applicable in European Union countries.
e sy
ol on t e p o
ct o its pac a in si nifies t at t is p o
ct as to e
disposed separately from ordinary household wastes at its end of life. Please
in ly e a a e t at t is is yo
esponsi ility to ispose elect onic e
ip ent at
recycling centers so as to help conserve natural resources. Each country in the
European Union should have its collection centers for electrical and electronic
equipment recycling. For information about your recycling drop off area, please
contact your local related electrical and electronic equipment waste management
authority or the retailer where you bought the product.
5
PRECAUTIONS
Precautions
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
Symbols used in this manual
This icon indicates the existence of a potential hazard that could result in personal injury
or damage to the product.
This icon indicates important operating and servicing information.
Notice
• Read this User Manual carefully before using the LCD display and keep it for future reference.
•
epo
ct specifications an ot e in o
ation p o i e in t is
se
an al a e o e e ence only. ll
information is subject to change without notice. Updated content can be downloaded from our web site at
displays.agneovo.com.
• To register online, go to displays.agneovo.com.
• To protect your rights as a consumer, do not remove any stickers from the LCD display. Doing so may
affect the determination of the warranty period.
Cautions When Setting Up
Do not place the LCD display near heat sources, such as a heater, exhaust vent, or in direct
sunlight.
Do not cover or block the ventilation holes in the housing.
Place the LCD display on a stable area. Do not place the LCD display where it may subject
to vibration or shock.
Place the LCD display in a well-ventilated area.
Do not place the LCD display outdoors.
Do not place the LCD display in a dusty or humid environment.
Do not spill liquid or insert sharp objects into the LCD display through the ventilation holes.
Doin so
ay ca se acci ental fi e elect ic s oc o
6
a a et e
D isplay.
PRECAUTIONS
Cautions When Using
Use only the power cord supplied with the LCD
display.
The power outlet should be installed near the LCD
Warning:
display and be easily accessible.
Unplug the power cord
If an extension cord is used with the LCD display,
from the power outlet and
ensure that the total current consumption plugged
into the power outlet does not exceed the ampere
rating.
e e to
personnel under the following
conditions:
Do not allow anything to rest on the power cord. Do
not place the LCD display where the power cord
♦
D isplay
When the power cord is
damaged.
may be stepped on.
t e
alifie se ice
ill not e se
o an in efinite
♦
If the LCD display has been
period of time, unplug the power cord from the
dropped or the housing has
power outlet.
been damaged.
To disconnect the power cord, grasp and pull by the
plug head. Do not tug on the cord; doing so may
♦
If the LCD display emits smoke
or a distinct odor.
ca se fi e o elect ic s oc .
Do not unplug or touch the power cord with wet
hands.
Warning:
Cleaning and Maintenance
Ceiling mount or mount
The LCD display comes with NeoVTM Optical
on any other horizontal
Glass. Use a soft cloth lightly moistened with a mild
surface overhead are not
detergent solution to clean the glass surface and the
advisable.
housing.
Do not rub or tap the surface of the glass with sharp
or abrasive items such as a pen or screwdriver. This
may result in scratching the surface of the glass.
Do not attempt to service the LCD display yourself,
e e to
alifie se ice pe sonnel.
penin o
Installation in contravention of
the instructions may result in
undesirable consequences,
particularly hurting people and
damaging property. Users who
have already mounted the
removing the covers may expose you to dangerous
display on the ceiling or any
voltage or other risks.
other horizontal surface overhead
are strongly advised to contact
eo o o cons ltations an
solutions to help ensure a most
pleas a le an
experience.
7
lfillin
isplay
PRECAUTIONS
Notice for the LCD Display
In order to maintain the stable luminous performance, it is recommended to use low brightness setting.
Due to the lifespan of the lamp, it is normal that the brightness quality of the LCD display may decrease
with time.
When static images are displayed for long periods of time, the image may cause an imprint on the LCD
display. This is called image retention or burn-in.
To prevent image retention, do any of the following:
• Set the LCD display to turn off after a few minutes of being idle.
• Use a screen saver that has moving graphics or a blank white image.
• Switch desktop backgrounds regularly.
•
st t e
D isplay to lo
i
tness settin s.
• Turn off the LCD display when the system is not in use.
Things to do when the LCD display shows image retention:
• Turn off the LCD display for extended periods of time. It can be several hours or several days.
• Use a screen saver and run it for extended periods of time.
• Use a black and white image and run it for extended periods of time.
When the LCD display is moved from one room to another or there is a sudden change from low to high
ambient temperature, dew condensation may form on or inside the glass surface. When this happens, do
not turn on the LCD display until the dew disappears.
Due to humid weather conditions, it is normal for mist to form inside the glass surface of the LCD display.
The mist will disappear after a few days or as soon as the weather stabilizes.
There are millions of micro transistors inside the LCD display. It is normal for a few transistors to be
damaged and to produce spots. This is acceptable and is not considered a failure.
8
CHAPTER 1: PRODUCT DESCRIPTION
Chapter 1: Product Description
1.1 Package Contents
When unpacking, check if the following items are included in
the package. If any of them is missing or damaged, contact your
dealer.
LCD Display
Quick Start Guide
Power adapter
Note:
Must use only the supplied power
adapter:
♦ ADAPTER TECH
Model no.: ATS040T-P120
Rating: 12V/3.3A
HX-24G
Quick Start Guide
HX-24G LCD Monitor
HX-24G_Quick Guide_V010
displays.agneovo.com
♦
Power cord
VGA cable
Audio cable
Warranty card
DELTA ELECTRONICS, INC.
Model no.: ADP-40GD BD2
Rating: 12V/3.33A
Note:
♦
The pictures are for reference
only. Actual items may vary
upon shipment.
9
PRODUCT DESCRIPTION
1.2 Wall Mounting Installation Preparation
Note:
1.2.1
To protect the glass panel, place a
Wall Mounting
towel or soft cloth before laying the
1
Remove the base stand.
LCD display down.
See procedures below.
2
Wall mount the LCD display.
Screw the mounting bracket to the VESA holes at
the rear of the LCD display.
Warning:
Ceiling mount or mount
100mm
on any other horizontal
surface overhead are not
advisable.
Installation in contravention of
the instructions may result in
100mm
75mm
undesirable consequences,
particularly hurting people and
damaging property. Users who
have already mounted the
75mm
display on the ceiling or any
other horizontal surface overhead
are strongly advised to contact
AG Neovo for consultations and
solutions to help ensure a most
pleas a le an
lfillin
isplay
experience.
Note:
Take measures to prevent the
LCD display from falling down
and lessen possible injury and
damage to the display in case of
earthquakes or other disasters.
♦
Use only the 75 x 75 mm and
100 x 100 mm wall mount kit
recommended by AG Neovo.
♦
Secure the LCD display on a
solid wall strong enough to bear
its weight.
10
PRODUCT DESCRIPTION
1.2.2
1
2
Removing the Base Stand
ay t e
D isplay ace o n on a at e en s
Remove the screws* securing the base stand from the LCD
display.
3
ace.
Detach the base stand.
11
Note:
(*) The screw size is M4 x 10mm.
PRODUCT DESCRIPTION
1.3 LCD Display Overview
1.3.1
Front View and Keypad Buttons
1
1
2
3
4
5
AUTO
Hot Key: Auto Adjustment/Rotate
• For VGA input signal source, press to
perform auto adjustment.
• Press for 3 seconds to enable the Rotate
function.
• When OSD menu is ON, press to close the
OSD menu or exit a submenu.
2
LEFT
Hot Key: Audio Volume Adjustment
• Press to display the volume bar. Then press
the LEFT key to decrease the volume.
• When OSD menu is ON, press to select an
option or adjust the settings.
3
RIGHT
Hot Key: Screen Freeze
• Press to activate the screen freeze function.
To deactivate, press any key except for the
Power key.
• When the volume bar appears, press to
increase the volume.
• When OSD menu is ON, press to select
and option, adjust the settings, or enter the
submenu.
12
6
7
8
4
UP
Hot Key: PIP/PBP Select
• Press repeatedly to select PIP/PBP option
.
• When OSD menu is ON, press to select an
option or adjust the settings.
5
DOWN
Hot Key: PICTURE MODE Select
• Press repeatedly to select PICTURE MODE
option Stan a
D
.
• When OSD menu is ON, press to select an
option or adjust the settings.
• When PIP is ON, press to swap the PIP
main and sub picture.
6
MENU
Press to display/hide the OSD menu.
7
SOURCE
Press to select the input signal source.
8
POWER and LED Indicator
• Press to turn the power on or off.
• Indicate the operating status of the LCD
display:
- Lights Green when the LCD display is
turned on.
- Lights Amber when the LCD display is in
standby mode.
- Lights Off when the LCD display is turned
off.
PRODUCT DESCRIPTION
1.3.2
Rear View
SDI
OUT
IN
7
8
COMPOSITE
IN
OUT
9
10
AUDIO
L
11
IN
R
USB (SERVICE)
DC IN
DVI
HDMI DisplayPort
VGA
12
AUDIO IN
RS232
13
1
2
3
4
5
6
1
DC IN
Connect with the supplied power adaptor.
9
COMPOSITE IN
Connect Composite (CVBS) signals input.
2
DVI
Connect DVI signals input.
10 COMPOSITE OUT
Connect Composite (CVBS) signals output.
3
HDMI
Connect HDMI signals input.
11 AUDIO IN
Connect audio signals input (RCA Stereo
Audio Jack).
4
DisplayPort
Connect DisplayPort signals input.
5
VGA
Connect VGA signals input.
6
AUDIO IN
Connect audio signals input (3.5 mm Stereo
Audio Jack).
7
SDI OUT
Connect SDI signals output.
8
SDI IN
Connect SDI signals input.
12 USB (SERVICE)
Connect USB 2.0 for service.
13 RS232
Connect RS232 input from external
equipment.
13
CHAPTER 2: MAKING CONNECTIONS
Chapter 2: Making Connections
2.1 Connecting the Power
1
Connect the power cord to the power adapter.
2
Connect the power adapter to the DC power input at the rear of the LCD display.
3
Connect the power cord plug to a power outlet or a power supply.
DC IN
Caution:
♦
Make sure that the LCD display is
not connected to the power outlet
before making any connections.
Connecting cables while the power
is ON may cause electric shock or
personal injury.
Caution:
♦
When unplugging the power cord,
hold the power cord by the plug
head. Never pull by the cord.
14
MAKING CONNECTIONS
2.2 Connecting Input Source Signals
2.2.1
Connecting a Computer
Using VGA Cables
Connect one end of a VGA cable to the VGA connector of the LCD display and the other end to the VGA
connector of the computer.
VGA
Using DVI Cables
Connect one end of a DVI (DVI-D) cable to the DVI connector of the LCD display and the other end to the DVI
connector of the computer.
DVI
15
MAKING CONNECTIONS
Using HDMI Cables
Connect one end of an HDMI cable to the HDMI connector of the LCD display and the other end to the HDMI
connector of the computer.
HDMI
Using DisplayPort Cables
Connect one end of a DisplayPort cable to the DisplayPort connector of the LCD display and the other end to
the DisplayPort connector of the computer.
DisplayPort
16
MAKING CONNECTIONS
Using RS232 Cables
Connect one end of an RS232 cable to the RS232 connector of the LCD display and the other end to the
RS232 connector of the computer.
RS232
Using Audio Cables
Connect one end of an audio cable to the AUDIO IN connector at the rear of the LCD display and the other
end to the audio out connector of the computer.
AUDIO IN
17
MAKING CONNECTIONS
2.2.2
Connecting a Video Device
Using Composite (CVBS) Cables
Connect one end of a Composite (CVBS) cable to the COMPOSITE IN connector of the LCD display and the
other end to the Composite (CVBS) connectors of your device.
For audio input, connect an RCA cable to the AUDIO IN connectors of the LCD display and the audio out
connector of your device.
For video looping, connect one end of a Composite (CVBS) cable to the COMPOSITE OUT connector of the
LCD display and the other end to the COMPOSITE IN connector of the additional display.
COMPOSITE
COMPOSITE
IN
IN
OUT
OUT
AUDIO
AUDIO
L
L
IN
IN
R
R
or
Using SDI Cables
Connect one end of an SDI cable to the SDI IN connector of the LCD display and the other end to the SDI
connectors of your device.
For video looping, connect one end of an SDI cable to the SDI OUT connector of the LCD display and the
other end to the SDI IN connector of the additional display.
SDI
SDI
OUT
OUT
IN
IN
or
18
MAKING CONNECTIONS
Using HDMI Cables
Connect one end of an HDMI cable to the HDMI connector of the LCD display and the other end to the HDMI
connector of your device.
HDMI
Using DisplayPort Cables
Connect one end of a DisplayPort cable to the DisplayPort connector of the LCD display and the other end to
the DisplayPort connector of your device.
DisplayPort
19
CHAPTER 3: USING THE LCD DISPLAY
Chapter 3: Using the LCD Display
3.1 Turning on the Power
Note:
POWER button
♦
LED indicator
1
Connect the power cord to the power adapter. Then
connect the power adapter to the DC power input at the
The LCD display still consumes
power as long as the power
cord is connected to the power
outlet. Disconnect the power
cord to completely cut off
power.
rear of the LCD display.
2
Press the POWER button to turn the LCD display on.
The LED indicator turns GREEN.
When the LCD display is turned on, press the POWER
button to turn off the LCD display.
The LED indicator turns off.
3.2 Selecting the Input Source Signal
Notes:
♦
After selecting an input source
signal, the input source signal
message appears on the
sc een
For example, HDMI is selected
the following message is
displayed.
SOURCE button
1
Press the
button to call out the input source menu.
V G A
HDMI
♦
D V I
H D M I
D I S P L AY P O R T
C O M P O S I T E
S D I
2
3
ie y.
Press the p or q button to highlight an input source.
INPUT
If the selected input source
signal is not connected to the
LCD display or is turned off, the
no signal message is displayed
on the screen.
NO
SIGNAL
Press the u button to select the input source.
♦
If the resolution or the graphics
card of the connected computer
is set too high, the input out of
range message is displayed.
INPUT SIGNAL
OUT OF RANGE
20
USING THE LCD DISPLAY
3.3 Adjusting the Volume
Hot Key: Audio Volume Adjustment
1
Press the t button to call out the volume bar.
2
Press the u button to increase volume or the t button to decrease volume.
3.3.1
Muting the Audio
Press the u and t buttons simultaneously to mute or unmute the audio.
3.4 Choosing Your Preferred Picture Settings
Hot Key: PICTURE MODE Select
Press the q button repeatedly to toggle between the picture modes.
Options are as follows:
• STANDARD MODE: Default settings that suits most environments and types of video.
• CCTV MODE: Settings adjusted for monitoring CCTV.
• VIDEO MODE: Settings adjusted for video.
S TA N D A R D M O D E
CCTV MODE
21
VIDEO MODE
USING THE LCD DISPLAY
3.5 Using Picture-in-Picture (PIP)
The Picture-in-Picture (PIP) and Picture-by-Picture (PIP) feature allows viewing of more than one input source
signal on the LCD display.
3.5.1
PIP/PBP Options
Hot Key: PIP/PBP Select
Press the p button repeatedly to enable and scroll among the PIP/PBP options. Options are as follows:
• PIP On: The sub source signal is displayed within the main source signal.
• PBP (Picture-by-Picture): The main source and the sub source signals are displayed side by side with
equal display size.
• PIP Off: PIP function is disabled, only the main source signal is displayed.
PIP On
PBP
Note:
♦
The main source and sub
source signals can be set in
PIP Setting, see page 38.
PIP Off
♦
Some input source signal
combinations do not support
PIP. See PIP Compatibility
table on page 39.
22
USING THE LCD DISPLAY
3.5.2
PIP/PBP Swap
The main and the sub source signals set in PIP/PBP Setting can be
easily swapped using the keypad.
Note:
Sub source
Main source
♦
PIP/PBP Swap can only be
executed if PIP is enabled, see
page 38.
Press the q button to swap the main source and the sub source
signals. See illustration below.
Sub source
Main source
3.6 Using FREEZE Function
Hot Key: Screen Freeze
The FREEZE function allows you to freeze the screen image but still
continues real-time playback until the image is unfreeze.
Press the u button to activate screen freeze, the screen freeze
message is displayed on the screen.
Freeze On
You can press any button to deactivate except the POWER button.
23
USING THE LCD DISPLAY
3.7 Using Auto Adjustment Function
Note:
♦
Auto Adjustment function is
available only during VGA input
signals.
♦
Hot Key: Auto Adjustment/Rotate
auto adjustment function when
Auto Adjustment function automatically tunes the LCD display to its
using the LCD display for the
optimal setting, including horizontal position, vertical position, clock,
fi st ti e o a te a esol tion o
and phase.
Press the
It is recommended to use the
frequency change.
button to perform auto adjustment.
♦
The message auto adjusting is displayed on the screen.
It is recommended to perform
the Auto Adjustment function
only when the image (non-
AUTO
ADJUSTING
black) is displayed in full
screen.
During auto adjustment, the screen will slightly shake for a few
seconds.
When the message disappears, auto adjustment is completed.
3.8 Using ROTATE Function
The ROTATE function allows you to rotate the screen image at 180°.
Press the
button for 3 seconds to rotate the picture 180º.
Note:
♦
ROTATE function can only be
executed if PIP is off, see page
38.
After ROTATE
image
After executing ROTATE, press the
button for 3 seconds again to
rotate the picture back to its normal state.
Original screen
image
24
USING THE LCD DISPLAY
3.9 Locking the OSD Menu
Lock the OSD menu to protect the LCD display from unauthorised users or from accidentally pressing the
keypad.
To lock the OSD, press and hold the keypad buttons listed below for at least 5 seconds or until the
OSD
LOCK OUT
message appears.
When the OSD is locked, all keypad buttons are inactivated.
Type of OSD Lock
Lock all buttons
Lock Operation
Press and hold the u, p, and q
buttons simultaneously for 5 seconds.
Unlock Operation
Do one of the following to unlock:
• Press and hold the u, p, and
q buttons simultaneously for 5
seconds or until the OSD menu
appears.
Lock all buttons except
Press and hold the t, p, and q
the POWER button.
buttons simultaneously for 5 seconds.
• Press and hold the t, p, and
q buttons simultaneously for 5
seconds or until the OSD menu
appears.
25
CHAPTER 4: ON SCREEN DISPLAY MENU
Chapter 4: On Screen Display Menu
4.1 Using the OSD Menu
Operation
1
Display the main menu screen.
1 9 2 0 x 1 0 8 0
Press the
button.
6 0 H z
B R I G H T N E S S
5 0
BRIGHTNESS
C O N T R A S T
5 0
C O L O U R T E M P.
B A C K L I G H T
6 0
IMAGE SETTING
B L A C K
L E V E L
5 0
ASPECT RATIO
PIP SETTING
ANTI-BURN-IN
OSD SETTING
AUDIO SETTING
SYSTEM 1
SYSTEM 2
ECOSMART SENSOR
INPUT SELECT
LANGUAGE
Navigation Window
INFORMATION
E X I T
2
E N T E R
S E L E C T
1 Press the p or q button.
Select the menu.
1 9 2 0 x 1 0 8 0
6 0 H z
2 Press the u button to enter the
B R I G H T N E S S
5 0
BRIGHTNESS
submenu.
C O N T R A S T
5 0
C O L O U R T E M P.
B A C K L I G H T
6 0
IMAGE SETTING
B L A C K
L E V E L
5 0
ASPECT RATIO
PIP SETTING
ANTI-BURN-IN
OSD SETTING
AUDIO SETTING
SYSTEM 1
SYSTEM 2
ECOSMART SENSOR
INPUT SELECT
LANGUAGE
INFORMATION
E X I T
E N T E R
S E L E C T
26
ON SCREEN DISPLAY MENU
Operation
Press the p or q button.
Select the submenu item.
3
0 x 1 0 8 0
6 0 H z
B R I G H T N E S S
5 0
RIGHTNESS
C O N T R A S T
5 0
O L O U R T E M P.
B A C K L I G H T
6 0
AGE SETTING
B L A C K
L E V E L
5 0
SPECT RATIO
P SETTING
The highlighted item with an orange arrow indicates the active
NTI-BURN-IN
submenu.
SD SETTING
4
Adjust the settings.
Press the t or u button.
5
Exit the submenu.
Press the
UDIO SETTING
YSTEM 1
YSTEM 2
or
button to return to
the previous menu.
COSMART SENSOR
PUT SELECT
ANGUAGE
Close the OSD window.
6
Press the
or
button again.
FORMATION
I T
en settin s a e
o ifie
A D J U S T
all c an es a e sa e
en t e se
oes t e ollo in
S E L E C T
• Proceeds to the another menu.
• Exits the OSD menu.
•
aits o t e
Note:
SD
en to isappea .
aila ility o so e
en ite s epen on t e inp t so ce si nal.
disabled and grayed out.
27
t e
en is not a aila le it is
ON SCREEN DISPLAY MENU
4.2 OSD Menu Tree
1 9 2 0 x 1 0 8 0
6 0 H z
B R I G H T N E S S
5 0
BRIGHTNESS
1
C O N T R A S T
2
C O L O U R T E M P.
3
IMAGE SETTING
5 0
B A C K L I G H T
6 0
B L A C K
Main Menu
1.
SS
4
ASPECT RATIO
5
PIP SETTING
6
ANTI-BURN-IN
5 0
OSD SETTING
7
AUDIO SETTING
8
SYSTEM 1
9
SYSTEM 2
10
ECOSMART SENSOR
11
INPUT SELECT
12
LANGUAGE
13
INFORMATION
14
Submenu
E N
E X I T
SS
•
L E V E L
T E R
Remarks
S E L E C T
See page 31.
• CONTRAST
•
• BLACK LEVEL
2. COLOUR TEMP.
• NEUTRAL
• WARM
• COOL
• USER
• AUTO COLOUR
28
See page 33.
ON SCREEN DISPLAY MENU
Main Menu
S
3.
Submenu
• S
SS
Remarks
See page 34.
• S
•
•
•
S
•
D
D
•
•
.
S
•
.
S
S
•
• CLOCK
4. S
See page 37.
• FULL
• REAL
•
• ZOOM
• OVERSCAN
5.
S
See page 38.
•
S
•
• SUB SOURCE
• S
S
• S
.
S.
• SWAP
6.
See page 40.
• ENABLE
S
•
• MODE
7.
8.
SD S
D
• TRANSPARENCY
S
•
SD
.
S
•
SD .
S
•
SD
See page 42.
• VOLUME
•
See page 41.
D
• SOURCE
9. SYSTEM 1
•
S
• SOURCE DETECT
• DD
• BLUE SCREEN
• S
• Alink
•
• LED
• RESET
29
See page 43.
ON SCREEN DISPLAY MENU
Main Menu
10. SYSTEM 2
Submenu
• S
Remarks
S
See page 45.
D
•
• DCR
11. ECOSMART SENSOR
•
D
•
D
See page 46.
• ENABLE
• MODE
• LEVEL
12.
S
See page 48.
•
• D
D
•
• DS
S
•
• SD
13.
Select t e
SD lan
D
a e
S
S
NL / 简中 / 繁中
1 .
Displays settin s in o
esol tion
o i ontal
e
i in
ency
Version.
30
ation s c as np t
e
o e an
ency
i
e tical
ae
CHAPTER 5: ADJUSTING THE LCD DISPLAY
Chapter 5: Adjusting the LCD Display
5.1 Brightness
1 9 2 0 x 1 0 8 0
6 0 H z
1. Press the
B R I G H T N E S S
5 0
BRIGHTNESS
button to call out the
OSD window.
C O N T R A S T
5 0
C O L O U R T E M P.
B A C K L I G H T
6 0
IMAGE SETTING
B L A C K
2. Select BRIGHTNESS menu, then
press the u button.
L E V E L
5 0
ASPECT RATIO
PIP SETTING
3. Press the p or q button to select an
option.
ANTI-BURN-IN
OSD SETTING
AUDIO SETTING
SYSTEM 1
SYSTEM 2
ECOSMART SENSOR
INPUT SELECT
LANGUAGE
INFORMATION
E X I T
Item
BRIGHTNESS
CONTRAST
BACKLIGHT
A D J U S T
S E L E C T
Function
Operation
Adjusts the luminance of the
screen image.
Adjusts the difference between the
black level and the white level.
Adjusts the luminance of the screen
image.
Press the t or u button to adjust
the
value.
Note: This menu option is not
available if the ECOSMART
SENSOR function is enabled.
BLACK LEVEL
Range
Adjusts the black level of the
screen image. Low brightness
setting makes black colour darker.
See comparison illustrations on page 32.
31
0 to 100
ADJUSTING THE LCD DISPLAY
Original Setting
High Setting
BRIGHTNESS
CONTRAST
BLACK LEVEL
32
Low Setting
ADJUSTING THE LCD DISPLAY
5.2 Colour Temp.
1 9 2 0 x 1 0 8 0
6 0 H z
1. Press the
N E U T R A L
window.
WA R M
BRIGHTNESS
button to call out the OSD
C O O L
U S E R
C O L O U R T E M P.
IMAGE SETTING
R
1 2 8
G
1 2 8
B
1 2 8
A U T O
ASPECT RATIO
2. Select COLOUR TEMP. menu, then
press the u button.
3. Press the p or q button to select an
C O L O U R
PIP SETTING
option.
ANTI-BURN-IN
OSD SETTING
AUDIO SETTING
SYSTEM 1
SYSTEM 2
ECOSMART SENSOR
INPUT SELECT
LANGUAGE
INFORMATION
E X I T
E N T E R
Item
S E L E C T
Function
Operation
Range
NEUTRAL
Provides several colour settings.
WARM
Press the t or u button
COOL
to select the setting.
USER
AUTO COLOUR
Colour setting can be set to:
• NEUTRAL - commonly used for normal lighting conditions.
• WARM - Applies a reddish tint for warmer colours.
• COOL - Applies a bluish tint for cooler colours.
COLOUR TEMP.
• USER - This allows users to set the colour temperature by adjusting the R, G, B
settings according to one’s preference.
1 Select USER, and press the u button.
2 Press the p or q button to select the colour you want to adjust.
3 Press the t or u button to adjust the values between 0 ~ 255.
• AUTO COLOUR - Operates the white balance and automatically adjusts the colour
settings.
1 Select AUTO COLOUR.
2 Press the u button to activate auto colour.
Note: This menu option is only available if the input source is VGA.
Note: Activate RESET to return the colour to its default setting.
33
ADJUSTING THE LCD DISPLAY
5.3 Image Setting
1 9 2 0 x 1 0 8 0
1. Press the
6 0 H z
S H A R P N E S S
BRIGHTNESS
button to call out the OSD
window.
0
S
CA
O TN UT R
RA
A TS I TO N
5 0
C O L O U R T E M P.
2. Select IMAGE SETTING menu, then
T I N T
press the u button.
5 0
IMAGE SETTING
ASPECT RATIO
G A M M A
2 . 0 2 . 2
PIP SETTING
C O L O U R R A N G E
A U T O
2 . 4
3. Press the p or q button to select an
S
option.
F U L L
ANTI-BURN-IN
L I M I T E D
N O I S E R E D U C T I O N
O F F
OSD SETTING
L O W
M I D
AUDIO SETTING
H I G H
P I C T U R E M O D E
S T A N D A R D
SYSTEM 1
C C T V
SYSTEM 2
V I D E O
ECOSMART SENSOR
H .
P O S I T I O N
INPUT SELECT
V.
P O S I T I O N
LANGUAGE
P H A S E
INFORMATION
C L O C K
5 0
5 0
5 0
5 0
E X I T
A D J U S T
Item
S E L E C T
Function
Operation
SHARPNESS
Adjusts the clarity and focus of the
screen image.
SATURATION
Adjusts the colour saturation.
TINT
Adjusts the colour tint.
Range
Press the t or u button to
0 to 100
adjust the value.
2.0
Adjusts the non-linear setting for
Press the t or u button to
2.2
picture luminance and contrast.
select the setting.
2.4
OUTPUT
OUTPUT
OUTPUT
OUTPUT
S
GAMMA
INPUT
INPUT
INPUT
INPUT
Display Gamma 2.0
Display Gamma 2.2
Display Gamma 2.4
Display Gamma S
34
ADJUSTING THE LCD DISPLAY
Item
Function
Operation
Range
Adjusts black and white levels for
video.
Press the t or u button to
Note: This menu option is only
available if the input source is HDMI.
select the setting.
AUTO
FULL
LIMITED
Signal source from PC - PC signal at a full range (Grayscale 0-255) state:
COLOUR RANGE
Monitor OSD colour range: Full *Please select
Monitor OSD colour range: Limited
Signal source from Video - Video signal at a limited range (Grayscale 16~235) state:
Monitor OSD colour range: Limited *Please select
Monitor OSD colour range: Full
OFF
Adjusts the noise reduction to help
remove noise from images. This
Press the t or u button to
LOW
helps produce clearer and crisper
select the setting.
MID
HIGH
images.
NOISE
REDUCTION
Noise Reduction Off
PICTURE MODE
Selects a p e efine pict e
Noise Reduction On
o e
setting.
Press the t or u button to
select the setting.
35
STANDARD
CCTV
VIDEO
ADJUSTING THE LCD DISPLAY
Item
Function
Operation
Range
Moves the screen image to the left
H. POSITION
(Horizontal Position) or right.
V. POSITION
(Vertical Position)
Moves the screen image up or down.
Adjusts the phase timing to
synchronise with the video signal.
PHASE
Note: This menu option is only
available if the input source is VGA.
Adjusts the frequency timing to
synchronise with the video signal.
CLOCK
Note: This menu option is only
available if the input source is VGA.
36
Press the t or u button to
adjust the value.
0 to 100
ADJUSTING THE LCD DISPLAY
5.4 Aspect Ratio
1 9 2 0 x 1 0 8 0
6 0 H z
1. Press the
F U L L
window.
R E A L
BRIGHTNESS
button to call out the OSD
N A T I V E
Z O O M
C O L O U R T E M P.
H .
2. Select ASPECT RATIO menu, then
Z O O M
press the u button.
1 0 0
IMAGE SETTING
V.
Z O O M
1 0 0
ASPECT RATIO
O V E R S C A N
PIP SETTING
3. Pressthe p or q button to select an
option.
0
ANTI-BURN-IN
OSD SETTING
AUDIO SETTING
SYSTEM 1
SYSTEM 2
ECOSMART SENSOR
INPUT SELECT
LANGUAGE
INFORMATION
E X I T
A D J U S T
Item
S E L E C T
Function
Operation
Range
FULL
Adjusts the aspect ratio of the screen Press the t or u button to
image.
select the setting.
REAL
NATIVE
ZOOM
OVERSCAN
The aspect ratio setting can be set to:
• FULL
ASPECT RATIO
nla es t e pict e to fill t e sc een.
• REAL - Displays the picture at its original size.
• NATIVE - Enlarges the picture but retain its original aspect ratio.
• ZOOM - Sets a custom aspect ratio by adjusting the horizontal zoom(H. ZOOM)
and /or vertical zoom(V.ZOOM) according to your preference.
1 Select ZOOM, and press the u button.
2 Press the p or q button to select the zoom parameter you want to adjust.
3 Press the t or u button to adjust the values between 0 ~ 100.
• OVERSCAN
sts t e o e scan settin to fi t e c t o sc een e
Press the t or u button to adjust the values between 0 ~ 100.
37
es.
ADJUSTING THE LCD DISPLAY
5.5 PIP Setting
1 9 2 0 x 1 0 8 0
6 0 H z
1. Press the
P I P
O F F
BRIGHTNESS
window.
P I P
P B P
C O L O U R T E M P.
2. Select PIP SETTING menu, then press
M A I N S O U R C E
V G A D V I
H D M I
IMAGE SETTING
the u button.
D I S P L A Y P O R T
C O M P O S I T E
ASPECT RATIO
3. Press the p or q button to select an
S D I
S U B S O U R C E
V G A D V I
H D M I
PIP SETTING
button to call out the OSD
option.
D I S P L A Y P O R T
ANTI-BURN-IN
C O M P O S I T E
S D I
OSD SETTING
S U B
1
AUDIO SETTING
P I C T U R E S I Z E
2
3
SYSTEM 1
S U B P I C . P O S .
L + U R + U
SYSTEM 2
S W A P
L + D
R + D
ECOSMART SENSOR
INPUT SELECT
LANGUAGE
INFORMATION
A D J U S T
E X I T
Item
PIP
S E L E C T
Function
Operation
Allows you to select the PIP setting
Press the t or u button to
or disable PIP.
select the value.
Range
OFF
PIP
PBP
PIP can be set to:
• OFF - Disables PIP.
• PIP - The sub source image is within the main source image.
• PBP - The main source and sub source images are displayed side by side.
MAIN SOURCE
Allows you to select the main source
VGA
signal.
DVI
Press the t or u button to
SUB SOURCE
Allows you to select the sub source
select the setting.
HDMI
DISPLAYPORT
COMPOSITE
signal.
SDI
38
ADJUSTING THE LCD DISPLAY
Note: Any input signal may be set as the main or the sub source signal. However, some input signals are not
supported to be paired together as the main and the sub source signals.
Refer to the following table for compatibility options:
Main Source
Input Source
VGA
DVI
HDMI
DISPLAYPORT
SDI
COMPOSITE
VGA
X
O
O
O
O
O
DVI
O
X
O
O
O
O
O
O
X
O
O
O
O
O
O
X
O
O
SDI
O
O
O
O
X
X
COMPOSITE
O
O
O
O
X
X
HDMI
Sub
Source DISPLAYPORT
Item
Function
Operation
Allows you to select the size of the
sub source image.
Press the t or u button to
select the setting.
SIZE
Note: This menu option is only
available if the PIP setting is to PIP.
(Sub Picture
The size of the sub source image can be set to:
SUB PICTURE
Size)
Range
1
2
3
• 1 - Small image size.
• 2 - Medium image size.
• 3 - Large image size.
Allows you to select the position of
L+U
the sub source image.
Press the t or u button to
R+U
select the setting.
L+D
SUB PIC. POS.
Note: This menu option is only
available if the PIP setting is to PIP
(Sub Picture
The position of the sub source image can be set to:
Position)
R+D
• L+U - Sets the image on the upper left corner of the screen.
• R+U - Sets the image on the upper right corner of the screen.
• L+D - Sets the image on the lower left corner of the screen.
• R+D - Sets the image on the lower right corner of the screen.
SWAP
Swaps the main source and sub
Press the u
source signals.
the function.
39
tton to e ec te
-
ADJUSTING THE LCD DISPLAY
5.6 Anti-Burn-in
1 9 2 0 x 1 0 8 0
6 0 H z
1. Press the
BRIGHTNESS
E N A B L E
O N
C O L O U R T E M P.
I N T E R VA L ( H O U R S )
4
5
6
8
IMAGE SETTING
M O D E
A
B
O F F
button to call out the
OSD window.
2. Select ANTI-BURN-IN menu, then
press the u button.
C
3. Press the p or q button to select an
ASPECT RATIO
PIP SETTING
option.
ANTI-BURN-IN
OSD SETTING
AUDIO SETTING
SYSTEM 1
SYSTEM 2
ECOSMART SENSOR
INPUT SELECT
LANGUAGE
INFORMATION
A D J U S T
E X I T
Item
ENABLE
INTERVAL
(HOURS)
S E L E C T
Function
Operation
Enables or disables Anti-Burn-In
function.
Press the t or u button to select
ON
the setting.
OFF
4
Sets the interval time (hour)
between activating the Anti-Burn-In
function.
Press the t or u button to adjust
the value.
Press the t or u button to select
the setting.
Anti-Burn-In mode can be set to:
• A
5
6
8
Selects the Anti-Burn-In mode.
MODE
Range
ec tes ast.
• B - Slower but more precise than mode A.
• C - Slowest but the most precise anti-burn-in mode.
40
A
B
C
ADJUSTING THE LCD DISPLAY
5.7 OSD Setting
1 9 2 0 x 1 0 8 0
6 0 H z
1. Press the
T R A N S PA R E N C Y
0
BRIGHTNESS
O S D
H .
P O S I T I O N
O S D
V.
P O S I T I O N
5 0
C O L O U R T E M P.
5 0
IMAGE SETTING
O S D
button to call out the OSD
window.
2. Select OSD SETTING menu, then press
the u button.
T I M E R
ASPECT RATIO
1 5
PIP SETTING
3. Press the p or q button to select an
option.
ANTI-BURN-IN
OSD SETTING
AUDIO SETTING
SYSTEM 1
SYSTEM 2
ECOSMART SENSOR
INPUT SELECT
LANGUAGE
INFORMATION
E X I T
A D J U S T
Item
TRANSPARENCY
OSD H. POSITION
(Horizontal
Position)
S E L E C T
Function
Operation
Range
Adjusts the transparency level of the
OSD screen.
Moves the OSD window to the left or
0 to 100
right of the screen.
OSD V. POSITION
Moves the OSD window up or down
(Vertical Position)
the screen.
Press the t or u button to
adjust the value.
Sets the length of time (in seconds)
OSD TIMER
the OSD screen is displayed. When
the time elapses, the OSD screen is
automatically inactivated.
41
5 to 100
ADJUSTING THE LCD DISPLAY
5.8 Audio Setting
1 9 2 0 x 1 0 8 0
6 0 H z
1. Press the
V O L U M E
5 0
BRIGHTNESS
button to call out the OSD
window.
A U D I O
C O L O U R T E M P.
O N
2. Select AUDIO SETTING menu, then
O F F
press the u button.
S O U R C E
IMAGE SETTING
P C
V I D E O
3. Press the p or q button to select an
ASPECT RATIO
PIP SETTING
option.
ANTI-BURN-IN
OSD SETTING
AUDIO SETTING
SYSTEM 1
SYSTEM 2
ECOSMART SENSOR
INPUT SELECT
LANGUAGE
INFORMATION
E X I T
A D J U S T
Item
VOLUME
AUDIO
S E L E C T
Function
Operation
Adjusts the volume level of the builtin speaker.
0 to 100
ON
Turns the audio ON or OFF.
OFF
Selects the audio source for the PC
or Video input signal.
SOURCE
Press the t or u button to
adjust the value.
Range
Press the t or u button to
select the setting.
Note: This menu option is only
available if the input source is HDMI
or DisplayPort.
42
PC
VIDEO
ADJUSTING THE LCD DISPLAY
5.9 System 1
1 9 2 0 x 1 0 8 0
6 0 H z
P O W E R
BRIGHTNESS
1. Press the
S AV I N G
O N
S O U R C E
D E T E C T
A U T O
C O L O U R T E M P.
2. Select SYSTEM 1 menu, then press the
M A N U A L
IMAGE SETTING
u button.
D D C / C I
O N
ASPECT RATIO
B L U E
O F F
3. Press the p or q button to select an
S C R E E N
O N
O F F
PIP SETTING
S I G N A L
O N
ANTI-BURN-IN
button to call out the OSD
window.
O F F
option.
I N F O
O F F
A l i n k
O N
OSD SETTING
O F F
L O G O
AUDIO SETTING
O N
O F F
L E D
SYSTEM 1
O N
O F F
R E S E T
SYSTEM 2
ECOSMART SENSOR
INPUT SELECT
LANGUAGE
INFORMATION
E X I T
Item
A D J U S T
S E L E C T
Function
Operation
Range
Enables or disables power saving mode.
When the LCD display turns into power
saving mode, the screen turns black and the
LED indicator lights AMBER.
POWER
SAVING
Note: The amount of time for the display to
enter power saving varies depending on the
SOURCE DETECT setting. If the SOURCE
ON
DETECT is set to AUTO, the display checks
Press the t or u button to
all input source signals before entering
select the setting.
OFF
power saving mode if no signal is detected;
this takes up more time. If the SOURCE
DETECT is set to MANUAL, the display
enters power saving mode right away.
SOURCE
DETECT
Sets the display to automatically or manually
detect the input source signal.
43
AUTO
MANUAL
ADJUSTING THE LCD DISPLAY
Item
Function
Operation
Range
Press the t or u button to
ON
select the setting.
OFF
Activates the DDC/CI protocol to allow users
DDC/CI
to confi
et e
onito
y a so t a e sin
two wires on the VGA, HDMI, DisplayPort, or
DVI cables.
BLUE
SCREEN
SIGNAL INFO
Enables or disables the blue screen feature.
If the setting is set to ON, it displays a blue
screen when no signal is available.
Enables or disables the signal information to
be displayed on the screen.
Enables or disables HDMI Consumer
Electronics Control control.
If the setting is set to On, you can control the
Alink
connected HDMI-CEC compatible device on
the same power on or power off status.
Note: This menu option is only available if
the input source is HDMI.
Enables or disables the logo feature.
LOGO
If the setting is set to ON, the AG Neovo
lo o is
ie y isplaye a te t e isplay is
powered on.
LED
RESET
Sets the display LED indicator on or off.
se to eset all to e a lt settin s e cept
Press the u button to
e ec te t e
Language, and the input source.
44
nction.
-
ADJUSTING THE LCD DISPLAY
5.10 System 2
1 9 2 0 x 1 0 8 0
6 0 H z
S U P E R
1. Press the
R E S O L U T I O N
BRIGHTNESS
button to call out the OSD
window.
O F F
L O W
M I D
C O L O U R T E M P.
2. Select SYSTEM 2 menu, then press the
H I G H
IMAGE SETTING
u button.
O V E R D R I V E
O F F
ASPECT RATIO
3. Press the p or q button to select an
L O W
M I D
PIP SETTING
option.
H I G H
D C R
ANTI-BURN-IN
O N
N I G H T
OSD SETTING
O F F
M O D E
O N
O F F
M O N I T O R
AUDIO SETTING
I D
1
SYSTEM 1
SYSTEM 2
ECOSMART SENSOR
INPUT SELECT
LANGUAGE
INFORMATION
A D J U S T
E X I T
Item
S E L E C T
Function
Operation
Range
SUPER
Upscales images at a higher and more
OFF
RESOLUTION
detailed resolution for better clearness.
LOW
OVERDRIVE
Enhances the display response time.
MID
HIGH
Activates DCR. This feature provides
automatic adjustment of picture brightness
and contrast at high speed and dynamic
DCR
contrast range, such as when watching
(Dynamic
movies. DCR is suitable for indoor viewing.
Contrast Ratio)
Note: When the DCR function is activated,
the BACKLIGHT and ECOSMART SENSOR
function will be disabled.
Enables or disables the night mode feature.
When you are using the display in a dark
room, set the setting to ON. This allows user
to manually adjust backlight to lower than
NIGHT MODE
no
al le el o
ette
ie in e pe ience in
the dark environment.
Note: When the NIGHT MODE is activated,
the DCR and ECOSMART SENSOR
functions will be disabled.
45
Press the t or u button to
select the setting.
ON
OFF
ADJUSTING THE LCD DISPLAY
Item
Function
Operation
Range
Sets the ID number for controlling the
MONITOR ID
display via the RS232 connection. Each
Press the t or u button to
display must have a unique ID number when
set the ID.
1~255
multiple sets of this display are connected.
5.11 EcoSmart Sensor
With the built-in EcoSmart sensor, users can enable the Eco Smart feature to automatically adjust the LCD
screen brightness according to the ambient light. This feature comforts the eyes and helps optimise energy
e ficiency.
Note: Please make sure the EcoSmart sensor is not covered when enabling this function.
EcoSmart
sensor
1 9 2 0 x 1 0 8 0
6 0 H z
1. Press the
E N A B L E
O N
BRIGHTNESS
button to call out the OSD
window.
O F F
M O D E
A U T O
C O L O U R T E M P.
2. Select ECOSMART SENSOR menu,
U S E R
IMAGE SETTING
then press the u button.
L E V E L
8 0
3. Press the p or q button to select an
ASPECT RATIO
PIP SETTING
option.
ANTI-BURN-IN
OSD SETTING
AUDIO SETTING
SYSTEM 1
SYSTEM 2
ECOSMART SENSOR
INPUT SELECT
LANGUAGE
INFORMATION
E X I T
A D J U S T
S E L E C T
46
ADJUSTING THE LCD DISPLAY
Item
ENABLE
Function
Operation
Enables or disables the Eco Smart
Press the t or u button to
ON
feature.
select the setting.
OFF
Sets the auto brightness mode.
MODE
Value
Press the t or u button to
AUTO
select the setting.
USER
The mode can be set to:
• AUTO - This mode is the default mode. The LCD brightness automatically adjusts
to the ambient brightness.
• USER - Allows you to manually adjust the LCD brightness.
Allows you to set the level of LCD
brightness.
LEVEL
Note: This menu option is only
available if the MODE setting is to
USER.
47
Press the t or u button to
adjust the value.
0 to 100
ADJUSTING THE LCD DISPLAY
5.12 Input Select
1 9 2 0 x 1 0 8 0
6 0 H z
1. Press the
V G A
button to call out the OSD
window.
D V I
BRIGHTNESS
H D M I
D I S P L AY P O R T
C O L O U R T E M P.
2. Select INPUT SELECT menu, then press
C O M P O S I T E
IMAGE SETTING
the u button.
S D I
3. Press the p or q button to select an
ASPECT RATIO
PIP SETTING
option.
ANTI-BURN-IN
OSD SETTING
AUDIO SETTING
SYSTEM 1
SYSTEM 2
ECOSMART SENSOR
INPUT SELECT
LANGUAGE
INFORMATION
E X I T
E N T E R
Item
S E L E C T
Function
Operation
VGA
Sets VGA as the input source signal.
DVI
Sets DVI as the input source signal.
HDMI
DISPLAYPORT
COMPOSITE
SDI
Value
Sets HDMI as the input source
signal.
Sets DisplayPort as the input source
signal.
Sets COMPOSITE as the input
source signal.
Sets SDI as the input source signal.
48
Press the u button to switch to
the selected input source.
-
CHAPTER 6: APPENDIX
Chapter 6: Appendix
6.1 Warning Messages
Warning Messages
Cause
The resolution or the refresh rate of
INPUT SIGNAL
OUT OF RANGE
Solution
• Change the resolution or the
the graphics card of the computer
refresh rate of the graphics
is set too high.
card.
The LCD display cannot detect the
input source signal.
• Check if the input source is
turned ON.
• Check if the signal cable is
NO
SIGNAL
properly connected.
• Check if any pin inside the
cable connector is twisted or
broken.
OSD
LOCK OUT
ANTI-BURN-IN
ON
ANTI-BURN-IN
OFF
The OSD has been locked by the
user.
• Unlock the OSD. Refer to page
25.
The Anti-Burn-In function has been
enabled by the user.
The Anti-Burn-In function has been
disabled by the user.
49
• Disable the Anti-Burn-In
function. Refer to page 40.
• Enable the Anti-Burn-In
function. Refer to page 40.
APPENDIX
6.2 Supported Resolutions
PC Mode
Resolution
Refresh Rate
Horizontal
Vertical
IBM VGA
720
400
70
IBM VGA
640
480
60
Apple Mac II
640
480
67
VESA
640
480
72
VESA
640
480
75
VESA
800
600
56
VESA
800
600
60
VESA
800
600
72
VESA
800
600
75
Apple Mac II
832
624
75
VESA
1024
768
60
VESA
1024
768
70
VESA
1024
768
75
VESA
1280
1024
60
VESA
1280
1024
75
Apple Mac II
1152
870
75
VESA
1152
864
75
VESA
1280
800
60
VESA
1280
800
75
VESA
1280
960
60
VESA
1440
900
60
VESA
1680
1050
60
VESA
1920
1080
60
Video Mode
Resolution
Refresh Rate
Horizontal
Vertical
EDTV
720
480
60i
EDTV
720
480
60
EDTV
720
576
50i
EDTV
720
576
50
HDTV
1280
720
50
EDTV
1280
720
60
HDTV
1920
1080
50i
HDTV
1920
1080
50
HDTV
1920
1080
60i
50
APPENDIX
Video Mode
Resolution
Refresh Rate
Horizontal
Vertical
HDTV
1920
1080
60
HDTV
1920
1080
24
HDTV
1920
1080
25
HDTV
1920
1080
30
6.3 Troubleshooting
Problem
No picture.
• LED indicator is OFF.
Possible Cause and Solution
• Check if the LCD display is turned ON.
• Check if the power cord is properly connected to the LCD display.
• Check if the power cord is plugged into the power outlet.
• LED indicator is
AMBER.
• Check if the computer is turned ON.
• Check if the computer is in standby mode, move the mouse or press
any key to wake up the computer.
Image position is incorrect.
• Adjust the H. POSITION and V. POSITION values. See IMAGE
SETTING on page 34.
The displayed texts are
blurry.
• For VGA input, press the
button on the keypad to auto-adjust the
display.
• Adjust the IMAGE SETTING (see page 34).
The OSD menu can’t be
• The OSD is locked. To unlock the OSD, see page 25.
called out.
Red, blue, green, white
dots appear on screen.
• There are millions of micro transistors inside the LCD display. It is
normal for a few transistors to be damaged and to produce spots. This
is acceptable and is not considered a failure.
No audio output.
• Check if the volume is set to 0 (see page 21 or 42).
• Check if the AUDIO SETTING > AUDIO setting is set to OFF (see page
42).
• For VGA or DVI input, check the audio setting of the computer.
• For HDMI or DisplayPort input, select the correct audio input source
(see page 42).
PIP mode does not work.
• The main and sub input source signals are not compatible to be
displayed together in PIP mode. Check the PIP Compatibility Table for
details (see page 39).
51
APPENDIX
Problem
Cannot adjust the backlight
setting.
Possible Cause and Solution
• The Eco Smart feature is enabled. Set the ECOSMART SENSOR >
ENABLE setting to OFF to disable the Eco Smart feature (see page
46).
The displayed picture looks
• Adjust the aspect ratio (see page 37).
distorted.
Dew formed on or inside
the LCD display.
• This normally happens when the LCD display is moved a cold room to
a hot room temperature. Do not turn ON the LCD display, wait for the
dew condensation to disappear.
Mist formed inside the
glass surface.
• This happens due to humid weather conditions. This is a normal
occurrence. The mist will disappear after a few days or as soon as the
weather stabilizes.
Faint shadows from a
static image appear on the
screen.
• Turn off the LCD display for extended periods of time.
• Use a screen saver or a black and white image and run it for extended
periods of time.
52
APPENDIX
6.4 Transporting the LCD Display
To transport the LCD display for repair or shipment, place the display in its original packaging carton.
1
Place the two foam cushions on each side of the LCD display for protection.
2
Place the LCD display down in the box.
3
Place the accessories box on the designated area (if necessary).
4
Close and tape the box.
53
CHAPTER 7: SPECIFICATIONS
Chapter 7: Specifications
7.1 Display Specifications
HX-24G
Panel
Panel Type
Panel Size
Max. Resolution
Pixel Pitch
Brightness
Contrast Ratio
Viewing Angle (H/V)
Display Colour
Response Time
Surface Treatment
Frequency (H/V)
H Freq.
V Freq.
SDI
DisplayPort
HDMI
DVI
VGA
Composite (CVBS)
SDI
Composite (CVBS)
RS232 In
USB
Audio In
Input
Output
External Control
Other Connectivity
Audio
SDI
Power
Glass
Operating Conditions
Storage Conditions
Mounting
Stand
Security
LED-Backlit TFT LCD (TN Technology)
23.6”
FHD 1920 x 1080
0.272 mm
300 cd/m2
20,000,000:1 (DCR)
170°/160°
16.7M
3 ms
Anti-Glare Treatment (Haze 25%),
2H Hard Coating
24 kHz-83 kHz
50 Hz-75 Hz
BNC x 1
x1
1.4 x 1
24-Pin DVI-D x 1
15-Pin D-Sub x 1
BNC x 1
BNC x 1
BNC x 1
2.5 mm Phone Jack
2.0 x1 (Service Port)
Stereo Audio Jack (3.5 mm)
Stereo Audio Jack (RCA)
2W x 2
1080p @50/60fps
720p @25/30/50/60fps,
1080p @24/25/30/50/60fps, 1080i @50/60fps
480i @60fps, 576i @50fps
External
DC 12V, 2.75A
25W (On)
< 0.5W
< 0.5W
3.0 mm (0.12”)
< 1%
> 97%
> 9H
0°C-40°C (32°F-104°F)
10%-90% (non-condensing)
-20°C-60°C (-4°F-140°F)
5%-95% (non-condensing)
Yes (100 x 100 mm & 75 x 75 mm)
0° to 18°
Yes
Internal Speakers
3G-SDI (SMPTE 424M)
HD-SDI (SMPTE 292M)
SD-SDI (SMPTE 259M)
Power Supply
Power Requirements
On Mode
Stand-by Mode
Off Mode
Thickness
e ection ate
Transmission Rate
Hardness
Temperature
Humidity
Temperature
Humidity
VESA FPMPMI
Tilt
Kensington Security Slot
54
SPECIFICATIONS
HX-24G
Dimensions
Weight
w/Base (W x H x D)
Packaging (W x H x D)
w/Base
Packaging
562.4 x 392.8 x 196.0 mm (22.1” x 15.4” x 7.7”)
672.0 x 517.0 x 249.0 mm (26.5” x 20.4” x 9.8”)
8.1 kg (17.9 lb)
11.2 kg (24.7 lb)
Note:
♦
ll specifications a e s
ect to c an e
it o t p io notice.
55
SPECIFICATIONS
7.2 Display Dimensions
53.5
HX-24G Dimensions
27.4
7.2.1
56.2
562.4(outline dimension)
32.6
538.6
522.3(opening dimension)
16.3
0°~18°
227.4
100
227.4
75
16.3
75
32.4
68.5
109.3
100
217.8
135.8
18.4
165.5
392.8
179.5
345
294.2(opening dimension)
352.6(outline dimension)
48.7
(M4xL10) x8
277.4
277.4
196
137.4
280
137.4
226
AG Neovo
Company Address: 5F-1, No. 3-1, Park Street, Nangang District, Taipei, 11503, Taiwan.
Copyright © 2019 AG Neovo. All rights reserved.
HX4G00_UM_V010
56
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement