Moxa CB-114 Series Quick Install Guide

Moxa CB-114 Series Quick Install Guide
CA Series for PC/104 and
CB Series for PC/104-Plus
Quick Installation Guide
Edition 1.1, November 2017
Technical Support Contact Information
www.moxa.com/support
Moxa Americas:
Toll-free: 1-888-669-2872
Tel:
1-714-528-6777
Fax: 1-714-528-6778
Moxa China (Shanghai office):
Toll-free: 800-820-5036
Tel:
+86-21-5258-9955
Fax: +86-21-5258-5505
Moxa Europe:
Tel:
+49-89-3 70 03 99-0
Fax: +49-89-3 70 03 99-99
Moxa Asia-Pacific:
Tel:
+886-2-8919-1230
Fax: +886-2-8919-1231
Moxa India:
Tel:
+91-80-4172-9088
Fax: +91-80-4132-1045
 2017 Moxa Inc. All rights reserved.
P/N: 1802001043315
*1802001043315*
Overview
Moxa offers a wide selection of PC/104 and PC/104-Plus serial boards that
provide industrial-grade connections to multiple serial devices. The CA
Serial Board Series is for PC/104 modules while the CB Serial Board series
is for PC/104-Plus module.
Package Checklist
PC/104 or PC/104-Plus boards are shipped with the following items:
•
•
•
•
Moxa multiport serial board (PC/104 module is for CA Series;
PC/104-Plus module is for CB Series)
Documentation and software CD
Quick installation guide (printed)
Warranty card
Please notify your sales representative if any of the above items are
missing or damaged.
Hardware Installation
The PC/104 or PC/104-Plus MUST be plugged into the PC before the driver
is installed. Follow these steps below.
CA Series
Step 1: Turn the embedded
computer off
Step 2: Set the I/O address,
Interrupt vector, IRQ, and
serial interface
(Refer to the section:
"Block Diagram, I/O
Address, Interrupt Vector,
Serial Interface")
Step 3: Insert the module into the
PC/104 slot
Step 4: Screw the control board in
place
Step 5: Connect the cables
(Refer to the section: "Pin
Assignments")
Step 6: Turn the embedded
computer on
CB Series
Step 1: Turn the embedded
computer off
Step 2: Set interface
(Refer to section: "Block
Diagram, I/O Address,
Interrupt Vector, Serial
Interface")
Step 3: Insert the module into
PC/104 slot.
Step 4: Screw the control board in
place.
Step 5: Connect the cables.
(Refer to the section: "Pin
Assignments")
Step 6: Turn the embedded
computer on.
Software Installation
Follow these steps:
Step 1: Get the driver at www.moxa.com or from the CD.
Based on the OS type, choose the corresponding driver.
Step 2: Install Driver
•
For Windows (Take the installation of Win7 as an example)
 2.1. Unzip and execute the .exe file

2.2. Follow the instructions to install the drivers
Note: If your model is from the CB Series, then the
installation is done. Otherwise, please do the following
-2-
steps for the CA Series models.
•

2.3. Follow the instructions of “Add Hardware Wizard”

2.4. Follow the instruction of “Found Hardware Wizard”.
This step is for mapping your driver and hardware device.

2.5. Repeat steps 2.3 and 2.4 to activate the other serial
ports.
For Linux
 2.1. Get the driver from CD and Unzip the file:
#mount /dev/cdrom /mnt/cdrom
#cd /
#mkdir moxa
#cd moxa
#cp /mnt/cdrom/<driver directory>/mxpcdrv.tgz
#tar xvfz mxpcdrv.tgz

2.2. Install the driver:
#cd mxser
#./mxinstall

2.3. Install the module driver, using the hardware
settings that you have selected
(This step is only for the CA Series)
For example: I/O address of 0x180, an INT vector of
0x1C0, and an IRQ of 10
#modprobe mxpcdrv ioaddr=0x180 iovect=0x1C0
irq=10

2.4. You can use the Moxa diagnostic utility to verify the
driver’s status:
#cd /moxa/mxpcdrv/utility/diag
#./msdiag

2.5 You can use the Moxa terminal utility to test the TTY
ports:
#cd /moxa/mxpcdrv/utility/term
#./msterm
Block Diagram, I/O Address, Interrupt Vector,
Serial Interface
Block Diagrams
CA Series
CA-108
CA-104 V2
-3-
CA-114
CA-134I,
CA-132 V2,
CA-132I V2
CB Series
CB-108
CB-114
CB-134I
I/O Address (Only for the CA Series)
Use DIP switch SW1 to set port 1’s I/O base address. The other ports will
be configured automatically.
The default I/O base address is 0×180 and allows settings from 0×000 to
0×3FF.
Some popular settings are provided below:
For example, an I/O base address of 0×180
should be set as follows:
A3
ON
A4
ON
A5
ON
A6
ON
A7
OFF
A8
OFF
A9
ON
Hex
0x180
The other serial ports will be set automatically to
0×188, 0×190, 0×198, etc.
-4-
Interrupt Vector (Only for CA Series)
A3
8
ON
ON
ON
ON
ON
ON
ON
off
off
off
off
off
off
off
A4
1
ON
ON
ON
ON
ON
ON
off
off
ON
off
off
off
off
off
A5
2
ON
ON
ON
ON
ON
off
off
off
ON
ON
off
off
off
off
A6
4
ON
ON
ON
ON
off
off
off
off
ON
ON
ON
off
off
off
A7
8
ON
ON
ON
off
off
off
off
off
ON
ON
ON
ON
off
off
A8
1
ON
ON
off
off
off
off
off
off
ON
ON
ON
ON
ON
ON
A9
2
ON
off
off
off
off
off
off
off
ON
ON
ON
ON
ON
off
Hex
0×000
0×200
0×300
0×380
0×3C0
0×3E0
0×3F0
0×3F8
0×008
0×018
0×038
0×078
0×0F8
0×2F8
Use DIP switch SW2 to set port 1’s interrupt vector.
The default interrupt vector is 0×1C0, with SW2 set as follows:
A3
ON
A4
ON
A5
ON
A6
ON
A7
OFF
A8
OFF
A9
ON
Hex
0x1C0
Serial Interface
CA Series
CA-114
Interface
SW1
SW2
SW3
RS-232
ON
RS-422
ON
OFF
-5-
RS-485 (4w)
ON
OFF
OFF
RS-485 (2w)
OFF
OFF
OFF
CA-134I, CA-132 V2, and CA-132I V2
Interface
RS-422
4-wire RS-485
2-wire RS-485
2-wire/4-wire
OFF
ON
RS-422/RS-485
OFF
ON
ON
CB Series
CB-114
Interface
SW1
SW2
SW3
RS-232
ON
RS-422
ON
OFF
RS-485 (4w)
ON
OFF
OFF
RS-485 (2w)
OFF
OFF
OFF
CB-134I
Interface
RS-422
4-wire RS-485
2-wire RS-485
2-wire/4-wire
OFF
ON
RS-422/RS-485
OFF
ON
ON
Pin Assignments
RS-232
(CA-108/CB-108, CA-114/CB-114, and CA-104)
NOTE
Pin
1
2
3
4
5
6
7
8
9
Note that there are two 40-pin box header connectors on the
CA-108/CB-108, of which each connects to 4 serial ports.
Signal
DCD0
DSR0
RxD0
RTS0
TxD0
CTS0
DTR0
–
GND0
Pin
11
12
13
14
15
16
17
18
19
Signal
DCD1
DSR1
RxD1
RTS1
TxD1
CTS1
DTR1
–
GND1
Pin
21
22
23
24
25
26
27
28
29
Signal
DCD2
DSR2
RxD2
RTS2
TxD2
CTS2
DTR2
–
GND2
Pin
31
32
33
34
35
36
37
38
39
Signal
DCD3
DSR3
RxD3
RTS3
TxD3
CTS3
DTR3
–
GND3
RS-422, 4-wire RS-485
(CA-132, CA-132I, CA-114/CB-114, and CA-134I)
With regard to the CA Series, pins 21 to 40 apply to CA-114 and CA-134I
only.
Pin
1
3
5
7
9
Signal
TxD0-(A)
TxD0+(B)
RxD0+(B)
RxD0-(A)
GND0
Pin
11
13
15
17
19
Signal
Pin* Signal* Pin* Signal*
TxD1-(A)
21
TxD2-(A)
31
TxD3-(A)
TxD1+(B) 23 TxD2+(B) 33 TxD3+(B)
RxD1+(B) 25 RxD2+(B) 35 RxD3+(B)
RxD1-(A)
27
RxD2-(A)
37
RxD3-(A)
GND1
29
GND2
39
GND3
-6-
2-wire RS-485
(CA-132, CA-132I, CA-114/CB-114, and CA-134I)
With regard to the CA Series, pins 21 to 40 apply to the CA-114 and
CA-134I only.
Pin
Signal
5
Data0+(B)
7
Data0-(A)
9
GND0
Pin
15
17
19
Signal
Pin* Signal* Pin* Signal*
Data1+(B) 25 Data2+(B) 35 Data3+(B)
Data1-(A) 27 Data2-(A) 37 Data3-(A)
GND1
29
GND2
39
GND3
-7-
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement