Bush WMNSN612W WMACHINE SI Instruction manual

Bush WMNSN612W WMACHINE SI Instruction manual
Washing Machine
Installation & User Instructions – Please keep for future reference
WMNSN612W
WMNSN612W
Important – Please read these instructions fully before installing or using
These instructions contain important information which will help you get the best from your
appliance and ensure safe and correct installation, use and maintenance.
If you need help or have damaged or missing parts, call the
Customer Helpline:0345 257 7271
52177938 - 17/11/15
If you have damaged or missing parts,
Contents
call the Customer Helpline: 0345 257 7271
Safety Information2
Parts3
Installation4
Unpacking your washing machine
4
Removing the packing bolts
4
Adjusting the feet4
Water inlet hose connection
5
Drain hose connection5
Electrical connection6
Introduction of control panel 7
Detergent drawer8
Programme selection10
Electronic display10
Auxiliary functions12
Child Lock14
Cancelling Programme14
Finishing Programme14
Programme Selection Guide
WMNSN612W
15
User Instructions16
Before first use16
Preparing for a wash
16
Error Signals17
Care and Maintenance
18
Water inlet filters18
Pump filter18
Detergent drawer19
Siphon plug19
Cabinet19
Drum20
Trouble Shooting21
Technical Specifications
23
Guarantee24
1 EN
Safety Information
Before use
• The installation of this appliance is best
carried out by 2 people.
• Dispose of all packing carefully and
responsibly.
• This appliance is for indoor use only. Only
install in a dry indoor environment.
• The appliance MUST be positioned on a firm
level base.
• Do not position the appliance where it is
exposed to direct sunlight or heat sources as this
will age the plastic and rubber components.
• Warning: Ensure all 4 packing
bolts have been removed.
• Ensure the appliance is connected directly to
a domestic mains water supply.
• Warning: This washing machine MUST only
be connected to a cold water supply.
• Ensure all electrical connections are as stated
in this document.
• Ensure the appliance is plugged into a
separate earthed socket that is easily accessible.
• Ensure the power lead is not trapped under
the appliance.
• Do not connect the appliance to the power
supply until installation is complete.
• This appliance is for domestic/household use
only and is not suitable for commercial use.
• Check that the water hose joints and
connections are secure and there are no leaks. If
the hoses leak, do not use until the leaks have been
stopped.
EN
2
During use
• This appliance is not to be used by children or
persons with reduced physical, sensory or mental
capabilities, Persons with lack of experience and
knowledge.
• Do not use a multiple socket or extension
cord.
• Do not use if the power lead is damaged. It
must be replaced by the manufacturer, their approved service agent or similarly qualified person.
Customer Helpline: 0345 257 7271.
• Do not insert the plug into the power supply
with wet hands.
• Do not touch or use the appliance when
barefoot or with wet or damp hands.
• Do not open the detergent drawer during a
wash cycle.
• Do not touch the porthole (door) during the
washing cycle - it will get hot.
• Never force the machine door
open while the machine is running.
• Do not open the door if water is visible
through the porthole.
• Do not wash foam rubber or sponge like
materials on a hot wash.
• The machine can reach high temperatures
while running. Do not touch the drain hose or
waste water during draining.
• Do not forget that the packing material of your
machine may be hazardous for children.
• Keep your pet away from your machine.
• Do not use flammable detergent, sprays or dry
cleaning agents in or near to the appliance.
• Do not remove or insert the plug in the
presence of flammable gas.
• The appliance should not be put on a carpet
which can block the air ventilation on the bottom
side.
• Do not place heavy objects or sources of heat
or damp on top of the washing machine.
• Only use detergents which are suitable for
automatic washing machines and follow the detergent manufacturers recommendations.
• Do not use this appliance if there are any
missing or damaged parts.
• Do not attempt to repair the appliance
yourself. Contact the manufacturer, their approved
service agent or the Customer Helpline:
0345 257 7271.
If you have damaged or missing parts,
Parts
call the Customer Helpline: 0345 257 7271
2
3
4
8
9
1
10
7
7
7
7
5
6
Front
1. Detergent drawer
2. Top panel
3. Start / Pause button
4. Programme selection dial
5. Door
6. Filter
Water inlet hose x 1
Back
7.Packing bolt x 4
8.Power lead
9.Drain hose
10.Water inlet
Plastic plug x 4
3 EN
If you have damaged or missing parts,
Installation
call the Customer Helpline: 0345 257 7271
1
2
Caution: 2 people are required to unpack the
washing machine, it is recommended that gloves
are worn.
X4
X4
a: Carefully remove all packaging materials including the foam base, dispose of correctly.
Note: When opened, water droplets may be visible in the drum etc. this is normal as each appliance is factory tested.
Important: The packing bolts are designed to
support the internal components during transit,
these MUST be removed before use.
3
X4
a: Loosen the screws by rotating counterclockwise
with a suitable wrench. (1 & 2)
b: Remove the bolts by pulling them. (3)
c: When the transport bolts have been removed,
insert the plastic transport screw taps found in the
accessories bag into the holes. (4)
a: For your machine to work efficiently with minimum vibration it should be settled on flat, nonslippery, firm ground.
5
b: You can adjust the balance of your machine by
changing the positioning of its feet.
c: First, loosen the plastic adjustment nut. (5)
d: Adjust by rotating the feet upwards or downwards. (6)
e: After the desired position has been reached,
tighten the plastic adjustment nut again by rotating it
upwards.
Note: Never put cartons, wooden blocks or similar
materials under the machine to balance irregularities in the level of the ground.
EN
4
6
X4
4
If you have damaged or missing parts,
Installation
call the Customer Helpline: 0345 257 7271
Important: This washing machine MUST only be
connected to a cold water supply.
7
8
a: Connect the water inlet hose, the angled connection attaches to the water inlet on the back of the
washing machine. (7)
b: The straight connection attaches to the water
supply valve. (8)
c: Ensure all seals are in place before connecting.
Important: Only tighten the hose connection nut
by hand - do not overtighten.
Important: The height of the top of the curve in the
drain hose MUST be between 60 - 100cm from
the floor. (9)
Important: The end of the water drain hose may
be fitted directly to the waste water outlet hole or a
special apparatus mounted on the outlet bracket of
the wash-stand.
Important: Never attempt to extend the water
drain hose by adding extra parts.
5 EN
If you have damaged or missing parts,
Installation
call the Customer Helpline: 0345 257 7271
Any electrical work that
is required to install this
washing machine MUST
be carried out by a
qualified electrician.
Warning: THIS
APPLIANCE MUST BE
EARTHED
Before making any electrical connections, ensure
that:
• Ensure the power socket is suitable for the maximum power of the washing machine (fuses in the
power circuit must be 13 amp).
• The supply voltage should be the same as that indicated in the technical specifications (page 17) and
the appliance rating plate (located where shown).
• The appliance should be earthed and in compliance with the applicable law.
• Additional earth cables should not be necessary
if the plug and socket are earthed. If necessary, an
additional earth cable should be attached to the
earth terminal on the back of the washing machine
and earthed.
• When installed, the power socket must be within
easy reach.
• The use of adapters, multiple connectors or
extension cables are not recommended.
• The appliance must be connected to a 220-240
volt 50 cycle AC supply by means of a three pin
socket, suitably earthed and protected by a 13 amp
fuse.
• Should the fuse need to be replaced, a 13 amp
fuse approved to BS1363/A must be used.
• The plug contains a removable fuse cover that
must be refitted when the fuse is replaced. If the
fuse cover is lost or damaged, the plug must not be
used until a replacement cover has been fitted or
the plug is replaced.
• A damaged plug should be cut off as close to the
plug body as possible, the fuse should be removed
and the plug disposed of safely.
EN
6
Plug replacement (UK & Ireland only)
Should you need to replace the plug; the wires in
the power cable are coloured in the following way:
Blue – Neutral ‘N’
Brown – Live ‘L’
Green & Yellow – Earth ‘E’
As the colours of the wires in the power cable may
not correspond with the coloured markings identifying the terminals in your plug, and proceed as
follows:
The green & yellow wire must be connected to the
terminal in the plug that is marked with the letter E
or by the earth symbol.
The blue wire must be connected to the terminal
that is marked with the letter N.
The brown wire must be connected to the terminal
that is marked with the letter L.
If the power lead is damaged, it must be replaced
by a qualified electrician.
Introduction of control panel
Programme knob
Display Panel
Detergent drawer
7 EN
Introduction of control panel
You can use the liquid level determination plate
when you want to wash your laundry with liquid
detergent. You can use your liquid detergents in all
programmes without prewashing. Place the liquid
detergent aparatus in the second compartment
(which is available inside the machine) of the
detergent drawer (*) and set the detergent amount.
(Use the
recommended amount of liquid detergent by detergent producers). Do not exceed the MAX level,
use only for liquid detergent, do not use this apparatus for powder detergent and take it out.)
Liquid Detergent Apparatus
Main wash detergent
compartment
Softener
Compartment
Pre-wash detergent
compartment
Powder detergent
level stages
Powder
detergent
spade (*)
(*) Machinery specifications may vary depending on
the product purchased.
EN
8
Introduction of control panel
Sections
Main wash detergent compartment:
In this compartment, only materials like
detergent (liquid or powder), lime preventer
and such can be used. You can find the liquid detergent aparatus inside your machine at first installation. (*)
Fabric conditioner, starch, detergent
compartment:
You can use softener for your laundry
(recommended amount and type by the producer is
recommended). Sometimes the fabric
conditioners you use for your laundry may remain
in this compartment. The reason for this is that the
conditioner is not viscous. To prevent this situation,
other liquid softeners are recommended to be used
or the softener could be thinned and then used.
Pre-wash detergent compartment:
This compartment must only be used when
the pre-wash feature is selected.
Pre-wash feature is recommended for very dirty
laundry.
(*) Machinery specifications may vary depending on
the product purchased.
9 EN
Introduction of control panel
Programme selection dial
With the programme knob, you can select the
programme with which you desire to wash your
clothes. You can select programmes by turning the
programme knob in both directions. You must be
careful that the adjustment sign of the programme
knob is exactly on the programme you want to
select. If you move the programme knob to 0
(off) position, while your machine is running, your
programme will be cancelled.
Note: If you want to activate an additional function
after the machine has started washing, press the
additional function button that you want to use. If the
additional function selected can still be used at that
programme stage, the LED of the function button
will be turned on and the function will be added
to the programme. If the LED is not turned on, the
function selected is not possible at that stage of the
current programme and will not be activated.
EN 10
On the display panel, you can see the washing
water temperature of your machine, speed setting
of your machine, the auxiliary functions you have
selected and the stage of the programme you are
running on your machine ( prewash/wash state, rinsing stage, spinning stage).
Furthermore, electronic display will warn you by
means of led combinations that will turn on its display when a fault occurs on your machine and notify
you of the completion of the washing programme
by revealing expression of “Finished” on the display
as soon as the washing programme you have
selected has finished as well.
Introduction of control panel
Display Panel
Washing
Rinsing
Spinning
Additional
Function
LEDS
Finished
Start/Pause button
Auxiliary function button 2
Auxiliary function button 1
Spin speed adjustment button
Water Temperature Adjustment Button
11 EN
Introduction of control panel
1- Temperature selection
You can select the washing water
temperature with the washing water
temperature adjustment button.
When you select a new programme, there
won’t be any display on the temperature
adjustment leds on the display panel.
When you press the temperature
adjustment button, the max.
temperature value of the programme
you have selected shall appear on the
led display panel.
You can gradually decrease the washing water
temperature between the maximum washing water
temperature of the selected programme and cold
washing selections by pressing temperature
adjustment button.
If you have missed the washing water temperature
you wanted, you can return to the intended temperature by continuously pressing the washing water
temperature adjustment button.
NOTE: When 90° programme is selected, the
max. temperature value of the selected programme
is not displayed on the display panel. When the
temperature value is decreased to 60°, 40°, 30°,
(cold washing) temperature levels by pressing
the temperature adjustment button, the decreased
temperature value is displayed on the display panel.
EN 12
Auxiliary
function
button 1
Introduction of control panel
2- Spin Speed Selection
4- Pre-wash
You can adjust the spin speed of your
laundry with the spin speed setting
button.
You can expose your very dirty laundries to prewashing operation prior to main washing by using
this additional function.
When using this function, you should put detergent
in front washing compartment of the detergent
drawer.
When you select a new programme, the
max. spin speed of the programme you
have selected shall be displayed on the display
panel. By pressing the spin speed setting
button, you can change the spin speed of the
selected programme between its max. value.
If you have
skipped the spin speed you want to
set, you can re-switch to the revolution by keeping
the speed setting button pressed.
Auxiliary
function
button 4
Auxiliary
function
button 2
3- Extra Rinse
You can make additional rinse operation
on your laundry by using this additional
function.
Start/Pause button
By pressing on the Start/Pause button,
you may start the programme you have
selected or suspend a running
programme. If you switch your machine
to the standby mode, the Start/Pause
led on the electronic display will blink.
You may make the programme active by
pressing the extra rinsing auxiliary function button
when the led light of the
symbol
turns on.
Auxiliary
function
button 3
13 EN
Introduction of control panel
To avoid programme flow from being affected if
programme buttons are pressed or programme button is turned when performing a washing operation
in your machine, a child lock is available.
Child lock will be activated when both auxiliary
functions 3 and 4 are pressed at the same time
for more than 3 seconds. You can see the auxiliary
function leds on the display when activated.
Your machine will stop by itself as soon as the
programme you have selected finishes.
If any button while child lock is active, the Additional
Function Leds will blink on the display.
- You can open the machine’s door and remove the
laundry.
If while the child lock is engaged and any programme is running, the programme knob is
switched to the CANCEL position and another
programme is selected, the programme previously
selected continues from where it left.
- Leave the door of your machine open to allow the
inner part of your machine to dry after removing
your laundries.
To deactivate the child lock, you should press on
the same buttons for more than 3 seconds. When
the child lock is deactivated, the Additional Function
Leds will blink on the display.
- Unplug your machine.
If you want to cancel any programme running:
1- Switch the programme knob to the “CANCEL”
position.
2- Your machine will stop the washing operation and
the programme will be cancelled.
3- To get rid of the water accumulated in the
machine switch the programme knob to any programme.
4- Your machine will perform the necessary discharge operation and cancel the programme.
5- You can run your machine by selecting a new
programme.
EN 14
- “End” led will blink on the display panel.
- Switch the programme knob to CANCEL position.
- Turn the water tap off.
Programme Selection Guide
Programme Washing Prog.
temTime
perature (mins)
(°c)
Detergent
compart.
Max
load
capacity
(kg)
Type of laundry
90°
Cotton
90°
Pre-wash 60°
cotton
60°
Cotton
eco
194
2
6
Very dirty, cotton and flax textiles. (Underwears, linen, tablecloth, towel
(maximum 3,0 kg), bedclothes, etc.
160
1&2
6
Dirty cotton and flax textiles. (Underwears, linen, tablecloth, towel (maximum
3,0 kg), bedclothes, etc.
200
2
6
Dirty cotton and flax textiles.
(Underwear, linen, tablecloth, towel (maximum 3,0 kg), bedclothes, etc.
Cotton
40°
190
2
6
Dirty cotton and flax textiles.
(Underwear, linen, tablecloth, towel (maximum 3,0 kg), bedclothes, etc.
Eco
20°
98
2
3
Less dirty, cotton and linen textiles. (Underwear, bedsheet, tablecloth, towel
(max. 2 kg) bedcloth, etc.
Easy care 40°
89
2
3
Very dirty or synthetic-mixed textiles. (Nylon socks, shirts, blouses, syntheticincluding trousers etc.)
Wool
Rinse
30°
40
2
2
Woollen clothing with machine wash labels.
-
36
-
6
If you want to additionally rinse your laundry upon completion of washing
operation, you may use this programme for any type of laundry.
Spin
-
15
-
6
If you want to additionally wring your laundry upon completion of washing
operation, you may use this programme for any type of laundry.
Hand
wash/
delicate
Sports
wear
30°
91
2
2
Laundry recommended for hand wash or sensitive laundry.
30°
80
2
3
Sportswear
Mixed
30°
87
2
3
Dirty cotton, synthetics, colour and flax textiles can be washed together.
Blouses / 60°
shirts
106
2
3
Dirty cotton, synthetic and synthetic-mixed shirts and blouses can be
washed together.
Daily 60 60°
min.
Rapid 15 30°
min.
60
2
3
You can wash your dirty cotton, colour and flax textiles at 60°C in 60
minutes.
15
2
2
You can wash your slightly stained, cotton, coloured and flax textile within
only 15 minutes.
(*) You can use softeners in all programmes (except spinning and draining programmes) optionally. When
you choose the quantity of the softener, comply with the warning of the softener producer. Fill your softener
in the (softener) compartment of the detergent drawer.
Note:Durations vary according to wash load (weight and type), tap water, ambient temperature and selected extra functions.
15 EN
If you have damaged or missing parts,
User
Instructions
call the Customer Helpline: 0345 257 7271
a: Plug in the machine.
b: Open the water tap.
c: There may be water left inside your machine after
factory tests and trials. It is recommended that the
first wash cycle be carried out with no laundry, to
remove this water; pour half a measuring cup of
normal laundry detergent into compartment 2 and
select cotton programme at 90°C.
Laundry
• Sort your clothes according to their types
(cotton, synthetic, delicate, woollen, etc.), washing
temperatures and level of dirtiness.
• Never wash your white and coloured clothes
together.
• Since your new coloured clothes may
release dye on the first wash, wash them separately.
• Remove any small objects from the pockets
of your clothes.
• Ensure that all zips and buttons on your
clothes are fastened.
• Remove the plastic or metal hooks of
curtains or place them inside a washing bag and tie.
• Turn clothes such as trousers, knitted
fabrics, t-shirts and sweat shirts inside out.
• Wash your small clothes like socks and
handkerchiefs in a washing bag.
Placing clothes into the machine
• Open the door of your machine.
• Put your clothes into your machine in a wellbalanced manner.
• Place your clothes loosely in the machine.
• When you shut the door of your machine, be
careful that no clothing is jammed between the
cover and the seals.
• Shut the door of your machine securely,
otherwise your machine will not start the washing
process.
Detergent
The quantity of detergent to be loaded into the
machine will depend on the following criteria:
• Your detergent consumption will change
depending on how dirty the clothes are. For your
EN 16
slightly dirty clothes, do not pre-wash and put a
small amount of detergent in compartment 2 of the
detergent drawer.
• For your excessively dirty clothes, select a
programme with pre-washing; fill ¼ portion of the
detergent in compartment 1 in the detergent drawer
and the remaining portion in compartment 2.
• Use detergents developed especially for
automatic washing machines. The quantities that will
be used for your clothes are written on the packaging of the detergents.
• As the hardness of your water increases, the
amount of the detergent to be consumed will also
increase.
• As the amount of clothing increases, the
amount of the detergent that will need to be used
will also increase.
• Fill your softener in the softener
compartment in your detergent drawer. Do not
exceed the MAX level. Otherwise, the softener will
diffuse in the washing water via the siphon.
• Concentrated softeners with high viscosity
should be diluted with water before loading in the
drawer. This is because high-viscosity softeners
obstruct the siphon and prevent the flow of the
softener.
• You can use liquid detergents in all
programmes without pre-washing. For this, fit the
liquid detergent level plate in the second compartment of the detergent drawer and arrange the
amount of liquid detergent according to the levels
on this plate.
If you have damaged or missing parts,
Error
Signals
call the Customer Helpline: 0345 257 7271
Your machine is equipped with systems which will take the necessary precautions and warn you in
case of any. IMPORTANT: IT CAN TAKE UPTO 10 MINUTES FOR ERROR TO
REGISTER.
Failure code
E01
Probable failure
Process to be followed
The door is not shut properly.
Shut the door properly so that you
hear the click. If the problem persists, turn off the machine unplug
and contact the nearest authorised
service agent immediately.
The water level in your machine is
below heater. The pressure of your
water supply may be low or water
supply may be blocked.
Turn on the tap fully. The water
supply may be interrupted. If the
problem persists, your machine will
automatically stop after a while.Unplug your machine, turn off the tap
and contact the nearest authorised
service agent immediately.
The pump has failed or the pump
filter is obstructed.
Clean the pump filter.If the
problem persists and contact the
nearest authorised service agent
immediately. (*)
Your machine has excessive
amount of water.
Your machine will discharge water
by itself. Pursuant to discharging
operation, turn off your machine
and unplug it. Turn off your tap
and contact the nearest authorised
service.
Wash
Rinse
E02
Wash
Rinse
End
E03
Wash
Rinse
End
E04
Wash
Rinse
(*) See the section regarding the care and maintenance of your machine.
17 EN
If you have damaged or missing parts,
Care
and
Maintenance
call the Customer Helpline: 0345 257 7271
Before cleaning your washing machine.
a: Unplug your machine from the mains power
supply.
b: Close the water tap.
Water inlet filters
On the tap part of your machine’s water inlet hose
and at the ends of water inlet valves, there are filters
to prevent entrance of the dirt and foreign materials
in the water to the machine. If the machine is unable
to receive sufficient water even though your water
tap is fully opened, filters should be cleaned.
• Remove the water inlet hose.
• Remove the filters found on the water inlet
valves by using a pincer and wash thoroughly with a
brush. (1)
• Clean the filters of the water inlet hoses
located on the tap side by removing manually
together with the seal. (2)
• After you clean the filters, you can fit them
the same way as you have removed them.
Pump filter
The pump filter system elongates the life of your
pump, which is used to drain the dirty water. It prevents dirt entering the pump. Cleaning of your pump
filter every 2-3 months is recommended. To clean
your pump filter:
• To open the pump cover, you can use the
powder detergent spade (*) or liquid detergent
level plate coming out of your machine. (1-A &
2-A)
• Before opening the filter cover,place a cup in front
of the filter cover to prevent flow of the remaining
water in the machine.
• Clean the foreign materials in the filter with a
brush and flush with clean water. (3-A)
• Check for the rotation of the pump manually.
• After cleaning the filter, fit the filter cover and
tighten it by rotating it in clockwise direction.
(4-A)
• Remove the foreign materials from the filter.
• Do not forget that if you do not fit the filter cover
properly, it will leak water.
• While closing the pump cover, ensure that the
parts on the inner side of the cover match the holes
on the front panel side. (5-A)
EN 18
• You can reattach the pump cover in the reverse
order that you removed it.
Danger of being scalded!
The water inside the pump
maybe hot- wait for it to cool.
(*) Machinery specifications may vary depending on
the product purchased.
If you have damaged or missing parts,
Care
and
Maintenance
call the Customer Helpline: 0345 257 7271
Detergent drawer
Detergents may form sediments in your detergent 1
drawer or in the housing of the detergent drawer
over time. To clean the sediment, pull out the
detergent drawer from time to time. To pull out the
detergent drawer:
• Pull the detergent drawer to the end. (1)
• Keep on pulling by depressing on the section
shown below in the detergent drawer and keep pulling and then remove the detergent drawer. (2&3) 2
• Clean the detergent drawer with a soft brush like
an old toothbrush and flush with clean water
• Collect residues in the housing of the detergent
drawer without dropping them inside the machine.
• Assemble the detergent drawer after drying it using a towel or dry cloth.
• Do not wash your detergent drawer
in a dishwasher!
3
Liquid Detergent Apparatus (*)
Take out the liquid detergent level apparatus for
cleaning and maintenance purposes as shown in
the picture and clean away detergent residues. Put
the apparatus back into its place. Make sure no
residues are left inside.
(*) Machinery specifications may vary depending on
the product purchased.
Siphon plug
Pull out the detergent drawer. Remove the siphon
plug and clean any residues away. Fit the cleaned
siphon plug in its location. Check it is placed properly.(3)
Cabinet
Clean the exterior surface of the cabinet of your
machine with lukewarm water and a cleaning substance that will not damage the cabinet. After rinsing
with clean water, wipe it with a soft and dry cloth.
Note:To get the best out of your machine. We
recomend that you periodically run a wash cycle
with limescale remover, especially in hard water
areas.
Note: After each wash leave the door of the
machine open to help air the drawer and
reduce any mould build up;
Note: Wipe the door seal ideally after each wash;
Note: Undertake a maintenance wash every 4-6
weeks with the drum empty. This wash should be
undertaken with lime scale and detergent remover;
19 EN
If you have damaged or missing parts,
Care
and
Maintenance
call the Customer Helpline: 0345 257 7271
Drum
Do not leave metallic objects such as needles,
paper clips, coins etc. in your machine. These
objects lead to stains in the drum. To clean such
rust stains, use a non-chlorine cleaning agent and
follow the instructions of manufacturers of the cleaning agent. Never use wire wool or similar hard
objects for cleaning rust stains.
EN 20
If you have damaged or missing parts,
Trouble
Shooting
call the Customer Helpline: 0345 257 7271
All repairs to the machine must be carried out by an authorised repair agent. When a repair is required or
you are unable to eliminate the failure with the help of the information below:
a: Unplug the machine.
b: Close the water tap.
c: Contact the nearest authorised repair agent.
FAILURE
PROBABLE CAUSE
Your machine does
not operate.
It is unplugged.
Your fuse is defective.
The electric power is off.
Start/pause button has not been
pressed.
The programme knob is in the 0 (off)
position.
The door is not shut properly.
Your machine does
not receive water.
Water tap is closed.
The water inlet hose may be bent.
The water inlet hose is obstructed.
The valve inlet filter is obstructed.
The door is not shut properly.
The drain hose is obstructed or bent.
Your machine is not The pump filter is obstructed.
draining water.
The clothes are not placed inside the
machine in a well-balanced manner.
The feet of your machine are not
Your machine is
adjusted.
vibrating.
Transportation screws are not removed.
There are only few clothes in the
device.
Excessive amount of clothes are filled
Your machine is
in the machine or the clothes are not
vibrating.
placed in a well-balanced manner.
Your machine is touching a rigid object.
METHODS OF
ELIMINATION
Insert the plug into the socket.
Change your fuse.
Check the electric power.
Press the start/pause button.
Turn the programme knob to the desired
position.
Shut the door properly. You should hear the
click.
Open water tap.
Check the water inlet hose.
Clean the filters of water inlet hose. (*)
Clean the valve inlet filters. (*)
Shut the door properly. You should hear the
click.
Check the drain hose.
Clean the pump filter. (*)
Spread the clothes inside the machine in an
orderly and well-balanced manner.
Adjust the feet. (**)
Remove transportation screws. (**)
It does not prevent operation of the machine.
Do not exceed the recommended quantity
of clothes and spread your clothes in the
machine in a well-balanced manner.
Ensure machine is not in contact with hard
objects.
(*) See the section concerning the care and maintenance of your machine.
(**) See the section concerning installation of your machine.
21 EN
If you have damaged or missing parts,
Trouble
Shooting
call the Customer Helpline: 0345 257 7271
FAILURE
Excessive foam
in the detergent
drawer.
PROBABLE CAUSE
Too much detergent has been used.
Wrong detergent has been used.
The washing result
is poor.
The washing result
is not good.
Your laundry is too dirty for the programme you have selected.
The amount of detergent used is not
sufficient.
Clothes exceeding the maximum
capacity have been loaded in the
machine.
Your water may be hard.
METHODS OF
ELIMINATION
Press the start/pause button.In order to stop
the foam,dilute one table-spoon of softener in
half liter of water and pour it in the detergent
drawer.Press the start/pause button after
5-10 minutes.Arrange the amount of the detergent properly in the next washing process.
Use only the detergents produced for full
automatic machines.
Select a suitable programme.
(see
page 8)
Use more detergent.
Put the clothes in your machine in a manner
not to exceed its maximum capacity.
Use the amount of detergent specified by the
detergent manufacturer.
Spread the clothes inside the machine in an
orderly and well-balanced manner .
Position the water drain at an appropriate
height.(**)
Distribution of the clothes in your machine is not well-balanced.
The water is drained The end of the water drain hose is in
from the machine as a position too low according to the
soon as it is filled.
machine.
No water is seen
No failure. The water is in the lower part in the drum during of the drum.
washing.
detergents contain ingredients
By adjusting your machine, carry out an
There are residues Some
which
are
not
soluble
in
water
and
additional rinse, or eliminate the stains after
of detergent on the which may form white stains on your
drying, with a brush.
clothes.
clothes.
There are grey
These stains may be caused by
In the next washing operation, use the
stains on the
oil,cream or ointment .
maximum detergent amount declared by the
clothes.
detergent producer.
No failure. The unbalanced load control The unbalanced load control system will try
may work in that way.
to distribute your clothes in a homogenous
The spinning promanner. After your clothes are distributed,
cess is not done or
passage to spining process will be realized. In
starts with delay .
the next washing process,place your clothes
into the machine in a well-balanced manner.
(*) See the section concerning the care and maintenance of your machine.
(**) See the section concerning installation of your machine.
EN 22
If you have damaged or missing parts,
Technical
Specifications
call the Customer Helpline: 0345 257 7271
Model / Item
Power supply
WMNSN612W
(220-240) V ~/50Hz
Max working current 10 amp
Water pressure
Maximum : 1Mpa
Minumum : 0.01 MPa
Maximum power
2100 watt
Maximum washing
load (dry)
6 kg
Spinning speed
1200 rpm
Washing
programmes
15
Size
845 x 597 x 497
Net weight
65 kg
The symbol on the product or its packaging indicates that this product may not be treated as
household waste. Instead it should be handed over to the applicable collection point for the
recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human
health, which could otherwise be caused by inappropriate waste handling of this product.
For more detailed information about recycling this product, please contact your local council
office, your household waste disposal service or the shop where the product was purchased.
23 EN
If you have damaged or missing parts,
Guarantee
call the Customer Helpline: 0345 257 7271
EN 24
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement