Mimaki RasterLinkPro5 SG Installation Guide

Mimaki RasterLinkPro5 SG Installation Guide
Software RIP
RasterLinkPro5
Installation Guide
This manual explains how to install
RasterLinkPro5.
MIMAKI ENGINEERING CO., LTD.
https://mimaki.com/
D202025-19
The kinds of manuals and how to use them
This product comes with following manuals.
Installation Guide
This manual explains how to install and set up
RasterLinkPro5 SG/RasterLink Pro5 IP/
RasterLinkPro5 TA.
you are now
reading this
manual.
Network Connection Guide
This manual explains how to set computer to connect to RasterLinkPro5 via network. (This is provided in PDF file in the manual CD.)
Reference Guide
There are two kinds of reference guides.
One is for common settings to each printer and the
other is for special settings to each printer.
They explain necessary setting items of the functions and operation in order to use RasterLinkPro5
SG/RasterLinkPro5 IP/RasterLinkPro5 TA.
Read the proper reference guide for your printer.
(This is provided in PDF file in the manual CD.)
Firmware Update Operation Manual
This manual explains how to use the update software for MIMAKI printer.
(This is provided in PDF file in the manual CD.)
Adobe, the Adobe logo, Photoshop, Illustrator and PostScript are trademarks of Adobe System Incorporated.
Apple, Macintosh, Power Macintosh, Mac OS and Mac OSX are registered trademarks of Apple Inc.
Microsoft, Windows, Windows 2000, Windows XP, Windows Vista, Windows 7, Windows 8 Windows 8.1 or
Windows 10 are trademarks of Microsoft Corporation and other countries.
PC MACLAN is registered trademarks of Miramar Systems, Inc.
All trademarks of Corel used in this document are trademarks or registered trademarks of the Corel Corporation
and its related companies in Canada, the United States and/or other countries.
All brand names and product names are trademarks or registered trademarks of their respective companies.
2
Notice
Notice
• It is strictly prohibited to write or copy a part or whole of this document without our approval.
• The contents of this document may be subject to change without notice.
• Due to improvement or change of this software, the description of this document could be partially
different in specification, for which your understanding is requested.
• It is strictly prohibited to copy this software to other disk (excluding the case for making backup) or
to load on the memory for the purpose other than executing it.
• With the exception of what is provided for in the warranty provisions of MIMAKI ENGINEERING
CO., LTD., we do not assume any liability against the damages (including but not limited to the loss
of profit, indirect damage, special damage or other monetary damages) arisen out of the use or failure to use of this product. The same shall also apply to the case even if MIMAKI ENGINEERING
CO., LTD. had been notified of the possibility of arising damages in advance. As an example, we
shall not be liable for any loss of the media (works) made using this product or indirect damages
caused by the product made using this media.
About this manual
This manual explains how to set PC for installing RasterLinkPro5.
This document explains the installation procedure using Windows Vista as an example.
Unless otherwise specified, use the same procedure for Windows XP, Windows 7, Windows 8,
Windows 8.1 and Windows 10.
Notations
Menu items are enclosed in quotation marks like “Full Color”.
Buttons in dialog box are framed like Close .
This manual is based on RasterLinkPro5 SG. Please replace software and printer names used
in this manual with those of the software and printer you are using.
Symbol
Indicates a caution you must observe when operating the product.
Describes a useful procedure.
Shows the number of the page that has related contents.
3
Table of Contents
The kinds of manuals and how to use them..........................................2
Notice ....................................................................................................3
About this manual .................................................................................3
About RasterLinkPro5 ...........................................................................6
System requirements ............................................................................9
Installing PC for RasterLinkPro5......................................................................9
Client PC........................................................................................................10
Set PC with RasterLinkPro5 installed............................... 11
RasterLinkPro5 Installation .................................................................12
Operations before installing RasterLinkPro5 .................................................12
Set the RasterLinkPro5 CD ...........................................................................13
Install the RasterLinkPro5..............................................................................14
License Activation ...............................................................................16
Activating the License....................................................................................16
Printer Registration to be used............................................................23
Starting printer management .........................................................................23
Adding a printer .............................................................................................27
Starting RasterLinkPro5 ......................................................................30
For Windows XP/ Vista / 7 .............................................................................30
For Windows 8...............................................................................................31
For Windows 8.1............................................................................................33
For Windows 10.............................................................................................35
Updating the Program .........................................................................37
For Windows XP/ Vista / 7 .............................................................................37
For Windows 8...............................................................................................38
For Windows 8.1............................................................................................39
For Windows 10.............................................................................................40
Updating the Profile.............................................................................41
4
For Windows XP/ Vista / 7............................................................................. 41
For Windows 8 .............................................................................................. 42
For Windows 8.1 ........................................................................................... 44
For Windows 10 ............................................................................................ 45
Setting Internet Connection Options ................................................... 47
Upgrade RasterLinkPro5 ................................................... 49
Updating version of RasterLinkPro5 ................................................... 50
Upgrading RasterLinkIII / RasterLinkPro4 series to RasterLinkPro5 .. 52
Uninstall RasterLinkPro5 ................................................... 55
Deactivating the License ..................................................................... 56
Checking the contents deletion in shared folder ................................. 61
Check that the folder contents are deleted ................................................... 62
Uninstall RasterLinkPro5..................................................................... 64
If an error occurs in license authentication..........................................67
How to release license authentication when PC has broken down............... 68
5
About RasterLinkPro5
RasterLinkPro5, which is application software, receives data in PostScript3 format and supplies printing data to an ink jet printer made by MIMAKI ENGINEERING.
Example of system configuration of RasterLinkPro5
Client PC
Sends image data to
RasterLinkPro5 installed PC.
Windows 98
Windows 2000
Windows XP
Windows Vista
Windows 7
Windows 8
Windows 8.1
Windows 10
Ethernet
RasterLinkPro5 PC
RasterLinkPro5 installed PC.
IEEE1394 Interface
Mimaki Printer
6
Macintosh
USB2.0 Interface
About RasterLinkPro5
Color Profile makes color matching easier
Installed Color Profile meets to various kinds of media and realizes the best print without
complicated settings.
Color adjustment function which enables delicate representation
RasterLinkPro5 has a function of adjustment to color (the tone-curve, contrast of each color,
and density of CMY ink).
It copes with various media flexibly.
Supported printers
RasterLinkPro5 is intended for use with MIMAKI ENGINEERING ink jet printers.
Up to 4 printers can be connected at the same time.*1
RasterLinkPro5 provides a number of different functions according to the features of the
printer. Functions and operational settings such as print condition and job editing differ
according to the printer. Therefore, there is a different Reference Guide for each printer type.
The Reference Guide is provided in PDF file in the manual CD.
Input/Output data
Input data
PostScript Level 3(PS file), EPS, MRL, TIFF, JPEG, BMP,
PDF (PDF 1.5 or later is not allowed *2)
Data formats other than MRL are automatically recognized.
AI files are not supported.
Alpha channel can not be used with TIFF data.
PostScript Font
Standard 60 European fonts
Adding fonts are not allowed.
Application
Adobe Illustrator 8, 9, 10, CS, CS2, CS3, CS4, CS5, CS6, CC, CC2014, CC2015
Adobe Photoshop 5, 6, 7, CS, CS2, CS3, CS4, CS5, CS6, CC, CC2014, CC2015
Maximum spool processible image size
Width : 10871 mm (428 inch)
Length : 10871 mm (428 inch)
7
Maximum RIP processible image size
Width : 50 meters
Length : 50 meters
Some output data even within above sizes may not be ripped, depending on
the kind of data.
In this case, change the data or divide the data by application software for
printing.
The largest image size which can be tiled *3
•Width: 50 meters, Length: 50 meters
•When the data width size exceeds the printable range of a printer, it is necessary to use the tiling function.
•Image sizes for tiling differ according to output resolutions.
•The maximum size of tiling-supported images depends on the input data. If the input data is too
complex, the maximum image size may not be printed.
• If the print resolution of the image is 1,440 x 1,440 dpi, the maximum printable image size is as follows.
Width
Length
4-color model
2m
50m
6-color model
1m
50m
• Even within the processable image size, the maximum size for width may be
restricted depending on the printer specifications.
Also even when using specialty ink (white ink and the like), the maximum
size for width may be restricted depending on the resolution.
Please check the "Max. printing width" in the manual of your printer.
*1: If multiple printers are connected with an IEEE1394 interface, the same number of
IEEE1394 interface cards are required.
*2:The PDF version and Acrobat version are as follows.
PDF 1.3 ----- Acrobat 4
PDF 1.4 ----- Acrobat 5
PDF 1.5 ----- Acrobat 6
PDF files saved with Illustrator are not supported.
*3:Some printers do not support the tiling function.
8
System requirements
System requirements
Installing PC for RasterLinkPro5
The following conditions are required to install RasterLinkPro5.
OS
: Microsoft® Windows® XP Professional Edition SP3 or later (32-bit)*1
: Microsoft® Windows® XP Home Edition SP3 or later (32-bit)*1
: Microsoft® Windows Vista® Home Premium SP2 or later (32-bit/64-bit)
: Microsoft® Windows Vista® Business SP2 or later (32-bit/64-bit)
: Microsoft® Windows Vista® Vista Ultimate SP2 or later (32-bit/64-bit)
: Microsoft® Windows Vista® Vista Enterprise SP2 or later (32-bit/64-bit)
: Microsoft® Windows 7® Home Premium (32-bit/64-bit)
: Microsoft® Windows 7® Professional (32-bit/64-bit)*2
: Microsoft® Windows 7® Ultimate (32-bit/64-bit)*2
: Microsoft® Windows 7® Enterprise (32-bit/64-bit)*2
: Microsoft® Windows 8® (32-bit/64-bit)
: Microsoft® Windows 8® Pro (32-bit/64-bit)
: Microsoft® Windows 8® Enterprise (32-bit/64-bit)
: Microsoft® Windows8.1® (32-bit/64-bit)
: Microsoft® Windows8.1® Pro (32-bit/64-bit)
: Microsoft® Windows8.1® Enterprise (32-bit/64-bit)
: Microsoft® Windows10® Home (32-bit/64-bit)
: Microsoft® Windows10® Pro (32-bit/64-bit)
: Microsoft® Windows10® Enterprise (32-bit/64-bit)
CPU
: Intel® CoreTM 2Duo 1.8GHz or more*3
Chip set
: Intel® chip set*3
Memory
: 2 GB or more
HDD
: 60 GB capacity recommended (NTFS format*4)
Interface
: IEEE1394*5, Ethernet Port*6, USB1.1/2.0 *7
*1 : Windows XP 64-bit is not supported.
*2 : It cannot be operated on the Windows XP mode of Windows 7.
*3 : For CPU or chip set, use the products made by Intel. If not using it, an error may occur during
printing and the printer may stop printing.
*4 : With the FAT32 format, problems occur when using hot folders from a Macintosh client.
*5 : It is required for connecting to the printer with IEEE1349 Interface.
Do not connect to printer using repeater hub. An error may occur during printing and the printer
may stop printing.
*6 : It is required for license activation. (Even if you do not connect with the Internet, or, you use a
PPP connection network device etc., it is required. )
For direct license activation from RasterLinkPro5, connect to the Internet.
When Macintosh is connected with PC MACLAN, Network card that supports AppleTalk is
needed.
*7 : USB 2.0 port is required for connecting to the printer with USB 2.0 interface.
Do not connect to the printer via a USB hub or an extension cable. An error may occur during
printing and the printer may stop printing.
9
USB 1.1 port or USB 2.0 port is needed to use the dongle. Do not connect the dongle via a USB
hub
Client PC
The client PC to be connected is limited depending on the OS of RasterLinkPro5 PC.
For the connection method, see “Network Connection Guide” in the manual CD.
10
Set PC with RasterLinkPro5 installed
RasterLinkPro5 PC is a PC on which RasterLinkPro5 is to be installed or already installed.
This is the explanation about necessary settings and the procedure of installation for operating
RasterLinkPro5 properly.
In this Installation Guide, the RasterLinkPro5 PC host name is described as
“RasterLink”. Where the explanation mentions “RasterLink”, substitute the host
name of your RasterLinkPro5 PC.
RasterLinkPro5 installation (
P.12)
Install the RasterLinkPro5.
License activation (
P.16)
Activate the RasterLinkPro5 license.
Printer Registration (
P.23)
Register printer on RasterLinkPro5.
Starting RasterLinkPro5 (
P.30)
Start the RasterLinkPro5
11
RasterLinkPro5 Installation
Operations before installing RasterLinkPro5
Perform the following operations before installing RasterLinkPro5.
1
Check whether the MIMAKI’s other software RIP is installed or not on the PC for
installation.
• If RasterLinkProII v2.0 or later / RasterLinkIII series / RasterLinkPro4 series is installed, see the following page.
?Upgrading RasterLinkIII / RasterLinkPro4 series to RasterLinkPro5? (P.52)
• If RasterLinkPro UJ / RasterLinkPro GP / RasterLinkProII v1.2 or before is installed, uninstall it.
• If RasterLinkPro is installed, you can install RasterLinkPro5 without any change. However, you cannot use RasterLinkPro when RasterLinkPro5 is running.
2
Check the Automatic Updates setting of Windows Update.
If you select “Automatic” on the [Automatic updates] of Windows Update, automatically update
program may be installed at the set times and the PC may be restarted. Once the PC is restarted
when RasterLinkPro5 is running, you can never start RasterLinkPro5. To prevent automatic
restart of the PC, select “Download updates for me, but let me choose when to install them.” on
the [Automatic Updates] of the [Control Panel].
3
Set data receiving from the client PC.
4
Install MIMAKI IEEE1394 driver / MIMAKI USB 2.0 driver.
Setting is required for receiving data from the client PC. See “Set PC with RasterLinkPro5
installed“ for details.
Check the interface used on the printer, and install the driver. Drivers are offered at the followings.
• Driver CD provided with the printer
• MIMAKI ENGINEERING website
· If using Windows 7/8/8.1/10, use the MIMAKI device driver Ver3.00 or later.
· Use the MIMAKI IEEE1394 driver Ver.2.20 or later, or MIMAKI USB2.0
driver Ver.1.10 or later.
12
RasterLinkPro5 Installation
Set the RasterLinkPro5 CD
Installing RasterLinkPro5 requires Administrator authority.
Insert the installation CD-ROM of RasterLinkPro5 into the CD drive, and the RasterLinkPro5
installation menu starts automatically.
In case the RasterLinkPro5 installation menu does not start automatically, double-click
“CDMenu.exe” in the CD-ROM.
ReadMe file is displayed. Please read it
before installation.
Start installing for
RasterLinkPro5.
(
P.14)
Start updating version
of RasterLinkPro5.
(
P.50)
Display the contents
of this CD.
Close this window.
When the User Account Control screen appears before starting the Installation
menu, click Continue .
Click
13
Install the RasterLinkPro5
1
Click Install RasterLinkPro5 in
the RasterLinkPro5 installation
menu.
Click
2
The confirmation screen for installing the USB dongle driver appears.
3
If Microsoft .NET Framework is not installed on your PC, the installer starts.
4
The “Choose Setup Language” dialog box appears.
OK
Click
.
Installation of the USB dongle driver starts.
Installation of the .Net Framework starts.
Select a setup language, and click
OK
.
1.Select
2.Click
5
Click
6
Select “I accept the terms in the
license agreement.”
Click
Next
Next
.
.
1.Select
2.Click
14
RasterLinkPro5 Installation
7
Specify a destination for the installation.
Specify a drive with sufficient spare
capacity.
Click
Next
.
Click
8
Click
9
RasterLinkPro5 installation finishes.
Click Finish .
Install
.
The RasterLinkPro5 files are copied to the installation destination.
the PC.
10 Restart
Yes
Click
to restart.
Click
After installing RasterLinkPro5, never do the following.
· Changing or deleting all the names of folder or file in the RasterLinkPro5installed folder.
15
License Activation
You can download the update program from our Web server and use the Program Update
(
P.37) or the Profile Update (
P.41) service to update RasterLinkPro5 to the latest version if you activate the license of RasterLinkPro5.
PC running RasterLinkPro5 needs to connect to the Internet to activate the license. If connecting to the Internet is not possible, you can use another PC that is connected to the Internet to
activate the license.
· When you activate the license, the serial key and information for identifying
the PC running RasterLinkPro5 (information generated automatically from
the PC hardware configuration) are sent to Mimaki Engineering.
· You can use RasterLinkPro5 without activating the license for a trial period
of 60 days from the time RasterLinkPro5 is first started. If the license is not
activated during the trial period, RasterLinkPro5 will no longer be able to be
used after the trial period ends.
· The program update (
P.37) or profile update (
P.41) cannot be used if
you have not activated the license.
Activating the License
This section explains how to activate the license.
When you activate the license, the serial key attached to RasterLInkPro5 is
required. Have the serial key at hand when you activate the license.
Start License Activation
If the license has not been activated, the license activation screen appears when you start RasterLinkPro5.
Or, start it as follows from the Windows [Start].
• Windows XP/Vista/7
[Start]-[All Programs]-[Mimaki RasterLinkPro5]-[License]-[License]
• Windows8
On [Start] screen, right-click to display the [All apps] icon.
Click the [All apps] icon to display the [Apps] screen.
In the [Mimaki RasterLinkPro5] category,m click the [License] icon.
• Windows10
[Start]-[All apps]-[Mimaki RasterLinkPro5]-[License]
Activate the License
There are two procedures for activating the license.
• Connect the PC running RasterLinkPro5 to the Internet and directly activate the license.
· If the PC running RasterLinkPro5 is not connected to the Internet, use another PC connected to the
Internet or make a request for activating the license to the place of purchase or our customer service,
and perform a substitute activation procedure ("Substitute License Activation Procedures"
P.18).
16
License Activation
When the PC running RasterLinkPro5 is connected to the Internet:
Confirm that the PC running RasterLinkPro5 is connected to the Internet
before activating the license.
1
Display the license activation screen.
If you are using a proxy
server, click [Internet access
option]. For the setting procedure, see
P.47.
1.Select
Select [Activate], and then click
Next .
2.Click
2
Enter the serial key.
Click
Next
.
1.Enter
2.Click
3
The server is accessed to activate the license.
If a personal firewall is set, a connection confirmation screen may appear.
If a screen appears, allow the connection.
4
The activation finishes.
2.Click
17
Substitute License Activation Procedures
If the PC running RasterLinkPro5 is not connected to the Internet, you can use the following
indirect license activation procedures.
· Use another PC connected to the Internet (hereafter referred to as "substitute PC") to activate the
license.
· Make a request for activating the license to the place of purchase or our customer service.
Follow the instructions below for these procedures.
1
Create an activation file in RasterLinkPro5.
P.19
activation file
2
If you have a PC connected to the
Internet, copy the activation file to
that PC and then activate the license.
P.20
If you do not have a setup in which connecting to the Internet is possible, the license can
be activated if you send the activation file to
the place of purchase or our customer service.
When you activate the license, a license key
file is created and sent. Copy the file to the
PC with RasterLinkPro5 installed.
3
18
substitute PC
place of purchase
or our customer
service
license key file
Read the license key file on the PC
running RasterLinkPro5, and register the license key in RasterLinkPro5.
License Activation
Creating an activation file
1
Display the license activation screen.
Click [Substitute activation.].
Click
2
Select [Create an activation file for
substitute activation.].
Specify the file name of the activation file.
Clicking Browse displays the [Save as
new file] dialog box so that you can specify
a file name.
Click
Next
1.Specify
.
2.Click
3
Enter the serial key.
Click
Next
.
1.Enter
2.Click
4
The work from the PC running RasterLinkPro5 is now finished.
Click
Finish
.
To use a substitute PC for the activation, copy
the activation file to the substitute PC.
To make a request for activating the license, contact either the place of purchase or our customer
service.
2.Click
19
Work from substitute PC
1
Start the Web browser and enter the
following address.
http://miws.mimaki.jp/license/
agencytop.aspx
Click
Click [Activation].
2
Click Browse .
The [File Upload] dialog box appears. Specify the activation file you saved on the PC
running Raster LinkPro5.
Click [Get license key].
1.Click
2.Click
3
The [File Download] dialog box
appears.
Click Save to open the [Save as] dialog
box.
Assign the file a suitable name.
The license key is issued, and the file is
saved.
Copy the saved license key file to the PC
running RasterLinkPro5.
20
Click
License Activation
Load the license key file
1
Redisplay the license activation
screen on the RasterLinkPro5 PC.
Click [Substitute activation.].
Click
2
Select [Input file name of the substitute activated license key file.].
Specify the file name of the license key file.
Clicking Browse displays the [Open the
license key file] dialog box so that you can
specify a file name.
Click
Next
1.Specify
.
2.Click
3
The activation finishes.
2.Click
21
Activating the License Later
If you want to try out RasterLinkPro5 or activate the license later, follow the procedure below.
1
Start license activation.
Select [Activate later], and then click
Next .
1.Select
2.Click
2
The trial period appears.
Activate the license within the
trial period.
Click
Finish
.
2.Click
22
Printer Registration to be used
Printer Registration to be used
One or more printer registration is required to use RasterLinkPro5. No printers are registered
immediately after RasterLinkPro5 is installed.
Start [Printer Management] to register printer.
• Please enable Windows Firewall Service before registering the printer. If
Windows Firewall Service is disabled, the printer cannot be registered.
Up to four printers can be registered.
Starting printer management
For Windows XP/ Vista / 7
1
2
In Windows select [Start] - [All
Programs] - [Mimaki RasterLinkPro5] - [Printer Management.].
Select
User Account Control screen is
displayed.
Click Continue .
Click
3
When first starting printer management, the setup work folder
screen appears.
Select a folder on a disk with sufficient
spare capacity.
A folder for saving the working files of
jobs is created automatically in the
selected folder.
1.Select
2.Click
23
For Windows 8
1
Right-click on the Start screen.
2
The screen changes to the application screen.
On the bottom-right side of the screen,
the [All apps] icon is displayed. Click it.
Click [Printer Management].
Click
3
User Account Control screen is
displayed.
Click Continue .
Click
4
When first starting printer management, the setup work folder
screen appears.
Select a folder on a disk with sufficient
spare capacity.
A folder for saving the working files of
jobs is created automatically in the
selected folder.
24
1.Select
2.Click
Printer Registration to be used
For Windows 8.1
1
On the Start screen, click the
arrow icon on the bottom-left of
the screen.
2
The screen changes to the application screen.
Click [Printer Management].
Click
3
User Account Control screen is
displayed.
Click Continue .
Click
4
When first starting printer management, the setup work folder
screen appears.
Select a folder on a disk with sufficient
spare capacity.
A folder for saving the working files of
jobs is created automatically in the
selected folder.
1.Select
2.Click
25
For Windows 10
1
In Windows select [Start] - [All
apps] - [Mimaki RasterLinkPro5] [Printer Management.].
Select
2
User Account Control screen is
displayed.
Yes
Click
.
Click
3
When first starting printer management, the setup work folder
screen appears.
Select a folder on a disk with sufficient
spare capacity.
A folder for saving the working files of
jobs is created automatically in the
selected folder.
26
1.Select
2.Click
Printer Registration to be used
Adding a printer
1
Turn on the printer, and check that the RasterLinkPro5 PC and printer are connected with a USB 2.0 cable or IEEE1394 cable.
· Before connecting multiple printers to RasterLinkPro5 with a USB 2.0 interface, it is necessary to change the "MACHINE NAME" of each printer to a
unique name on the Operation Panel.
· If multiple printers are connected to RasterLinkPro5 with an IEEE1394 interface, the same number of IEEE1394 interface cards are required. Multiple
printers cannot be connected to one IEEE1394 interface card.
2
On the printer management screen,
Add
click the
button.
Click
3
The printer setting screen appears.
If “IEEE1394” is specified for
[Output Port], the printer model
name and printer status (shown in
brackets) of connected printers are
shown in the [Available Printers]
list.
If several same model are
connected, the same model
names are shown in the
[Available Printers] list and it
may not be possible to identify the relevant printer. In
this case, switch between
the <REMOTE>/<LOCAL>
status on the printer Operation Panel, and click the
Update to Current Status
button to update the display
of the printer status.
If “USB 2.0” is specified for Port, the “MACHINE NAME” of the connected
printers are shown in the Available Printers list.
27
4
Select the [Model], [Color], and
[Available Printers] in accordance
with the printer actually connected.
Normally, specify “USB 2.0” or
“IEEE1394” for the [Output Port].
For the [Printer Name], enter a
simple name to identify the printer.
1.Select
3.Select
2.Click
4.Select
5.Enter
· When using a JV3-SL model, select JV3-SP 8 color. As for the device profile, install only the 4 color profile.
· The following single byte characters cannot be used for printer names.
\ / : * ? " < > | ! ,
· The printer name entered cannot be changed later. When a printer is added,
a default hot folder and printer driver are created with the printer name
entered. Also, the printer name entered here appears in the title of the execution status screen shown in the main window.
· When accessing the hot folder or shared printer from a PC with an OS earlier
than Windows ME, enter a printer name of single byte characters within 11 bytes.
· When registering two or more printers, duplicate printer names cannot be
registered. Be sure to register different printer names.
· RasterLinkPro5 outputs plotting data to the printer selected in the available
printer list and acquires its printer status (with “IEEE1394” the serial number
of the printer identifies the printer, and with “USB 2.0” the “MACHINE NAME”
identifies the printer). Therefore, when a different printer even of the same
model is connected, it is necessary to select it from the available printer list
and change its settings.
· When “IEEE1394” is selected for the output port, do not perform the following
actions when RasterLinkPro5 is running. It may cause the PC to freeze.
·Turn off the printer
·Pull out the IEEE1394 cable
If “File” is selected for the output port, a file can be created that can be printed
with the MIMAKI ENGINEERING printer command file output software NetLink.
28
Printer Registration to be used
5
OK
Click
Yes
Click
tion screen.
.
on the confirma-
The printer setting screen closes, and the
process to add the printer starts. The
progress is displayed in the information
field of the printer management screen.
When the process is complete, the message “Completed” is displayed.
· Do not force quit printer
management while a
printer is being added.
· If PC MACLAN is installed
on the RasterLinkPro5 PC,
the [PC MACLAN file
server warning] screen
may appear while the
printer is being added.
Click the
butOK
ton to stop the PC
MACLAN file server. The
PC is not shut down.
Click
Click
Do NOT perform the following operations with the printer driver of hot folder
created by printer management.
Changing the name, deleting them, changing the share name, or canceling
sharing.
(For the printer driver and the hot folder, see “Reference Guide Common features for every printer” in the manual CD.)
29
Starting RasterLinkPro5
Start the RasterLinkPro5 as follows.
License activation (
P.16) is required to use RasterLinkPro5. Activate the
license within 60 days after you first start RasterLinkPro5. Otherwise, RasterLinkPro5 will no longer be able to used after 60 days elapses.
If the license is not activated, the license activation screen appears each time
you start RasterLinkPro5.
For Windows XP/ Vista / 7
1
Select [Mimaki RasterLinkPro5];
[Start] - [All Programs] - [Mimaki
RasterLinkPro5] menu.
Or double-click the “Mimaki RasterLinkPro5” icon on the desktop.
Select
The RasterLinkPro5 start screen is displayed.
2
User Account Control screen is displayed.
Click Continue .
If the security center symbol (shield) is displayed
If the security center
symbol (shield) is displayed, in order for a
file to be executed, display the
User Account Control screen
and make sure that file execution is permitted.
30
Click
Starting RasterLinkPro5
3
The main window of RasterLinkPro5
is displayed.
For Windows 8
1
Right-click on the Start screen.
2
The screen changes to the application screen.
Click [Mimaki RasterLinkPro5].
On the bottom-right side of the screen,
the [All apps] icon is displayed. Click it.
Or, double-click the [Mimaki RasterLinkPro5] icon on the desktop.
Click
31
3
User Account Control screen is displayed.
Click Continue .
If the security center symbol (shield) is displayed
If the security center
symbol (shield) is displayed, in order for a
file to be executed, display the
User Account Control screen
and make sure that file execution is permitted.
4
32
The main window of RasterLinkPro5
is displayed.
Click
Starting RasterLinkPro5
For Windows 8.1
1
On the Start screen, click the
arrow icon on the bottom-left of
the screen.
2
The screen changes to the application screen.
Click [Mimaki RasterLinkPro5].
Or, double-click the [Mimaki RasterLinkPro5] icon on the desktop.
3
Click
User Account Control screen is displayed.
Click Continue .
If the security center symbol (shield) is displayed
Click
If the security center
symbol (shield) is displayed, in order for a
file to be executed, display the
User Account Control screen
and make sure that file execution is permitted.
33
4
34
The main window of RasterLinkPro5
is displayed.
Starting RasterLinkPro5
For Windows 10
1
In Windows select [Start] - [All apps]
- [Mimaki RasterLinkPro5] [Mimaki RasterLinkPro5].
Or double-click the “Mimaki RasterLinkPro5” icon on the desktop.
The RasterLinkPro5 start screen is displayed.
Select
2
User Account Control screen is displayed.
Click Yes .
If the security center symbol (shield) is displayed
Click
If the security center
symbol (shield) is displayed, in order for a
file to be executed, display the
User Account Control screen
and make sure that file execution is permitted.
35
3
36
The main window of RasterLinkPro5
is displayed.
Updating the Program
Updating the Program
You can use the Internet to update RasterLinkPro5.
· Make sure you connect the PC running RasterLinkPro5 to the Internet.
· The program update cannot be used if you have not activated the license.
· After installation, we recommend checking whether the latest updates are
available.
For Windows XP/ Vista / 7
1
Select [RasterLinkPro5] - [Update] [Program Update] from the Start
menu.
The program update starts.
Click
Next
.
Click
2
A connection is made to the Internet to check whether any updates are available.
If a personal firewall is set, a connection confirmation screen may appear.
If a screen appears, allow the connection.
3
If updates are available, a list of the
updates appears.
Select the updates you want to apply, and
Next
click
.
Click
4
The updates are downloaded.
5
Downloading of the updates finishes.
Click
Finish
to end the download procedure.
The updates are applied when RasterLinkPro5 is started.
37
For Windows 8
1
Right-click on the Start screen.
2
The screen changes to the application screen.
On the bottom-right side of the screen,
the [All apps] icon is displayed. Click it.
Click [Program Update].
3
A connection is made to the Internet to check whether any updates are available.
If a personal firewall is set, a connection confirmation screen may appear.
If a screen appears, allow the connection.
4
If updates are available, a list of the
updates appears.
Select the updates you want to apply, and
Next
click
.
Click
5
The updates are downloaded.
6
Downloading of the updates finishes.
Click
Finish
to end the download procedure.
The updates are applied when RasterLinkPro5 is started.
38
Updating the Program
For Windows 8.1
1
On the Start screen, click the
arrow icon on the bottom-left of
the screen.
2
The screen changes to the application screen.
Click [Program Update].
3
A connection is made to the Internet to check whether any updates are available.
If a personal firewall is set, a connection confirmation screen may appear.
If a screen appears, allow the connection.
4
If updates are available, a list of the
updates appears.
Select the updates you want to apply, and
Next
click
.
Click
5
The updates are downloaded.
6
Downloading of the updates finishes.
Click
Finish
to end the download procedure.
The updates are applied when RasterLinkPro5 is started.
39
For Windows 10
1
In Windows select [Start] - [All apps]
- [Mimaki RasterLinkPro5] - [Program Update.].
Select
2
A connection is made to the Internet to check whether any updates are available.
If a personal firewall is set, a connection confirmation screen may appear.
If a screen appears, allow the connection.
3
If updates are available, a list of the
updates appears.
Select the updates you want to apply, and
Next
click
.
Click
4
The updates are downloaded.
5
Downloading of the updates finishes.
Click
Finish
to end the download procedure.
The updates are applied when RasterLinkPro5 is started.
40
Updating the Profile
Updating the Profile
You can download and install the profile via the Internet.
· Make sure you connect the PC running RasterLinkPro5 to the Internet.
· The profile update cannot be used if you have not activated the license.
For Windows XP/ Vista / 7
1
Select [RasterLinkPro5] - [Update] - [Profile Update] from the Start menu.
The profile update starts.
Click
2
Next
.
Specify the printer and ink to install a
profile.
If [Show only registered printer] is checked,
only registered printer is displayed.
If unchecked, all printers usable on RasterLinkPro5 is displayed.
Click
3
Next
Click
.
Specify the option.
If [Show only newly released profiles] is
checked, only the profile released after the
day specified at the following options is
confirmed.
Select [Last downloaded] or [Specifies
date].
For [Specifies date], click [Calendar] to
select the date.
Click
Next
Specify
Click
.
41
4
Connect the Internet and check the profile.
If a personal firewall is set, a connection confirmation screen may appear.
If a screen appears, allow the connection.
5
If there are profiles that meet the settings, the list appears.
If [Do not show installed profile.] is
checked, installed profiles are not displayed.
Select
Select the profile to install, and click
Next .
6
Download the profile.
7
Downloading of the profile finishes.
Click
Finish
to end the download procedure.
The profile is installed when RasterLinkPro5 is started.
For Windows 8
1
Right-click on the Start screen.
2
The screen changes to the application screen.
On the bottom-right side of the screen,
the [All apps] icon is displayed. Click it.
Click [Profile Update].
42
Click
Updating the Profile
3
Specify the printer and ink to install a
profile.
If [Show only registered printer] is checked,
only registered printer is displayed.
If unchecked, all printers usable on RasterLinkPro5 is displayed.
Click
4
Next
Click
.
Specify the option.
If [Show only newly released profiles] is
checked, only the profile released after the
day specified at the following options is
confirmed.
Specify
Select [Last downloaded] or [Specifies
date].
For [Specifies date], click [Calendar] to
select the date.
Click
5
Next
Click
.
Connect the Internet and check the profile.
If a personal firewall is set, a connection confirmation screen may appear.
If a screen appears, allow the connection.
6
If there are profiles that meet the settings, the list appears.
If [Do not show installed profile.] is
checked, installed profiles are not displayed.
Select
Select the profile to install, and click
Next .
7
Download the profile.
8
Downloading of the profile finishes.
Click
Finish
Click
to end the download procedure.
The profile is installed when RasterLinkPro5 is started.
43
For Windows 8.1
1
On the Start screen, click the
arrow icon on the bottom-left of
the screen.
2
The screen changes to the application screen.
Click [Profile Update].
3
Specify the printer and ink to install a
profile.
If [Show only registered printer] is checked,
only registered printer is displayed.
If unchecked, all printers usable on RasterLinkPro5 is displayed.
Click
4
Next
Click
.
Specify the option.
If [Show only newly released profiles] is
checked, only the profile released after the
day specified at the following options is
confirmed.
Select [Last downloaded] or [Specifies
date].
For [Specifies date], click [Calendar] to
select the date.
Click
5
Next
Specify
Click
.
Connect the Internet and check the profile.
If a personal firewall is set, a connection confirmation screen may appear.
If a screen appears, allow the connection.
44
Updating the Profile
6
If there are profiles that meet the settings, the list appears.
If [Do not show installed profile.] is
checked, installed profiles are not displayed.
Select
Select the profile to install, and click
Next .
7
Download the profile.
8
Downloading of the profile finishes.
Click
Finish
Click
to end the download procedure.
The profile is installed when RasterLinkPro5 is started.
For Windows 10
1
In Windows select [Start] - [All apps]
- [Mimaki RasterLinkPro5] - [Profile
Update.].
Select
2
Specify the printer and ink to install a
profile.
If [Show only registered printer] is checked,
only registered printer is displayed.
If unchecked, all printers usable on RasterLinkPro5 is displayed.
Click
Next
Click
.
45
3
Specify the option.
If [Show only newly released profiles] is
checked, only the profile released after the
day specified at the following options is
confirmed.
Specify
Select [Last downloaded] or [Specifies
date].
For [Specifies date], click [Calendar] to
select the date.
Click
4
Next
Click
.
Connect the Internet and check the profile.
If a personal firewall is set, a connection confirmation screen may appear.
If a screen appears, allow the connection.
5
If there are profiles that meet the settings, the list appears.
If [Do not show installed profile.] is
checked, installed profiles are not displayed.
Select
Select the profile to install, and click
Next .
6
Download the profile.
7
Downloading of the profile finishes.
Click
Finish
to end the download procedure.
The profile is installed when RasterLinkPro5 is started.
46
Click
Setting Internet Connection Options
Setting Internet Connection Options
Set the options for connecting to the Internet to activate/release the license and update the program.
[Proxy server setting]
Specify this when using a proxy server to connect to the Internet.
47
48
Upgrade RasterLinkPro5
This section explains how to upgrade the RasterLinkPro5.
RasterLinkPro5 update (
P.50)
Update the RasterLinkPro5.
RasterLinkPro5 upgrade (
P.52)
Procedures how to upgrade from RasterLink III / RasterLinkPro4 series.
49
Updating version of RasterLinkPro5
1
Mount the installation CD for
RasterLinkPro5 whose version is
newer than the currently installed one
onto the PC.
The RasterLinkPro5 installation menu automatically starts.
Updating to an older version
cannot be executed.
2
Click
Update RasterLinkPro5
of RasterLinkPro5 installation menu.
Click
3
The “Choose Setup Language” dialog box appears.
Select a setup language, and click
OK
.
1.Select
2.Click
4
50
Click
Next
.
Updating version of RasterLinkPro5
5
Click
6
RasterLinkPro5 update finishes.
7
Restart the PC.
Yes
Click
to restart.
Install
.
Update starts.
Click
Finish
.
Click
51
Upgrading RasterLinkIII / RasterLinkPro4
series to RasterLinkPro5
For upgrading procedure from RasterLinkProII, refer to
“Manuual\English\Upgrade Guide_En.pdf” in the installation CD.
1
Mount the installation CD (upgrade
version) for RasterLinkPro5 onto the
PC.
The RasterLinkPro5 installation menu automatically starts.
2
Click
Upgrade RasterLinkPro5
of RasterLinkPro5 installation menu.
Click
3
The “Choose Setup Language” dialog box appears.
Select a setup language, and click
OK
.
1.Select
2.Click
4
Click
Next
.
Click
52
Upgrading RasterLinkIII / RasterLinkPro4 series to RasterLinkPro5
5
Click
Install
.
Start upgrading.
Click
6
Upgrading to RasterLinkPro5 is complete.
Click
Finish
.
Click
7
Restart the PC.
Click Yes
to restart.
Click
53
After upgrading, please follow the procedure below to update to the latest version.
1
Start up RasterLinkPro5.
2
Active the license.
3
RasterLinkPro5 will then startup.
4
Close RasterLinkPro5.
5
Use one of the following methods to update to the latest version.
For the "License Activation", see .
P.16.
Run Program Update.
For the "Program Update", see
P.37.
Download the update tool from the MIMAKI official website.
Please refer to the download page for instructions how to use the update tool.
54
Uninstall RasterLinkPro5
This section explains how to uninstall the RasterLinkPro5.
License Deactivation (
P.56)
Deactivate the license.
Check of the contents deleted in shared folder (
P.61)
When hot folders are used from MacOS 9.x,
delete the special folder in the shared folder.
RasterLinkPro5 Uninstallation (
P.64)
Uninstall the RasterLinkPro5.
55
Deactivating the License
To install and use RasterLinkPro5 on another PC, the license needs to be deactivated on the
PC on which the license is activated.
• If uninstalling before deactivating the license, a screen for deactivating the
license appears during uninstalling.
• Before installing RasterLinkPro5 on another PC, make sure to deactivate
the license on the PC on which the license is activated. Otherwise, license
activation will not be possible and you will not be able to use RasterLinkPro5
on another PC even if you install it on that PC.
Start License Release
Start it as follows from the Windows [Start].
• Windows XP/Vista/7
[Start]-[All Programs]-[Mimaki RasterLinkPro5]-[License]-[License]
• Windows8
On [Start] screen, right-click to display the [All apps] icon.
Click the [All apps] icon to display the [Apps] screen.
In the [Mimaki RasterLinkPro5] category, click the [License] icon.
• Windows8.1
On [Start] screen, Click the arrow icon of the bottom left of the screen to display the [Apps] screen.
In the [Mimaki RasterLinkPro5] category, click the [License] icon.
• Windows10
[Start]-[All apps]-[Mimaki RasterLinkPro5]-[License]
Deactivate the License
As with license activation, there are two procedures for deactivating the license.
• Connect the PC running RasterLinkPro5 to the Internet and directly deactivate the license.
• If the PC running RasterLinkPro5 is not connected to the Internet, use another PC connected to the
Internet or make a request for deactivating the license to the place of purchase or our customer service, and perform a substitute release procedure ("Substitute License Release Procedures"
P.58).
56
Deactivating the License
When the PC running RasterLinkPro5 is connected to the Internet:
1
Start the license deactivating process.
If you are using a proxy
server, click [Internet access
option]. For the setting procedure, see
P.47.
Click
Next
.
Click
2
The server is accessed to deactivate the license.
If a personal firewall is set, a connection confirmation screen may appear.
If a screen appears, allow the connection.
3
The license is deactivated.
57
Substitute License Deactivating Procedures
If the PC running RasterLinkPro5 is not connected to the Internet, you can use substitute
license deactivating procedures that are similar to the license activation procedures.
Follow the instructions below for these procedures.
1
Create a file for deactivating the
license in RasterLinkPro5.
P.58
2
If you have a PC connected to the
Internet, copy the deactivation file to
that PC and then deactivate the
license.
P.60
If you do not have a setup in which connecting to the Internet is possible, the license can
be deactivated if you send the deactivation
file to the place of purchase or our customer
service.
deactivation file
substitute PC
place of purchase
or our customer
service
Operation from PC Running RasterLinkPro5
1
Display the license de-activation
screen.
Click [Substitute de-activation.].
Click
58
Deactivating the License
2
Specify the save location of the deactivation file.
Click Browse to open the [Save the
license release file] dialog box.
Assign the file a suitable name and save the
file.
A deactivation file is created.
3
Click
Next
Click
Finish
.
1.Specify
2.Click
.
The work from the PC running RasterLinkPro5 is now finished.
At this point, RasterLinkPro5 can no longer
be used because the license has been deactivated.
To use a substitute PC for the license deactivating, copy the deactivation file to the substitute PC.
2.Click
To make a request for deactivating the
license, contact either the place of purchase
or our customer service.
Keep the deactivation file at hand until the deactivation is complete.
If lost before deactivating, RasterLinkPro5 cannot be used on the other PC
because of the inability to deactivate.
59
Operation from Substitute PC
1
Start the Web browser and enter the
following address.
http://miws.mimaki.jp/license/
agencytop.aspx
Click [Deactivation].
Click
2
Click Browse .
The [Chose file] dialog box appears. Specify
the deactivation file that you saved on the
PC running RasterLinkPro5.
1.Click
Click [Deactivation].
2.Click
The procedure is now complete.
60
Checking the contents deletion in shared folder
Checking the contents deletion in shared
folder
When using hot folders from Mac OS 9.x, after uninstalling RasterLinkPro5, there is possibility not to delete the installation directory.
Also when Deleting the Printer with [Printer Management], or when deleting the hot folder
with [Condition Management], the message “Cannot remove file in the Hot Folder” may
appear, and the process cannot be completed.
This occurs because the Macintosh client creates special folders and files in the hot folder.
To avoid this, before uninstalling RasterLinkPro5, deleting the Printer or deleting the hot
folder, delete the special folders in the shared folder.
The shared folders to delete are as follows.
· Before uninstallation
Installation folder\Hot\all hot folders
Installation folder\PPD
· Before deleting Printers with [Printer Management]
Installation folder\Hot\all hot folders
· Before deleting hot folders with [Condition Management]
Installation folder\Hot\condition set name hot folders
61
Check that the folder contents are deleted
This section describes how to check the hot folder as an example. Check PPD folder with the
same steps. In this example, JV3-SP is registered with [Printer Management].
1
In Explorer, select the hot folder in
the installation folder\Hot folder.
If there are no subfolders inside the hot
folder, deleting is not necessary.
Select
2
If there are subfolders in the hot
folder, select them with the mouse
and try deleting them with the
Delete key.
3
Yes
Click
on the “Delete Multiple Items” screen.
If subfolders are deleted, unmounting is not
necessary.
62
Click
Checking the contents deletion in shared folder
4
If an error message appears, the hot
folder is not deleted.
With the Macintosh client, move the
folder mounted by AppleShare to the
trash can to unmount it. If it is
already unmounted, mount the folder
again with AppleShare, then
unmount it.
5
After unmounting the folder in step
4, perform the operation in step 2
again, and check whether the subfolders inside the folder can be
deleted.
6
Perform steps 1 to 5 for all the subfolders in the installation folder\Hot
folder.
63
Uninstall RasterLinkPro5
• All RasterLinkPro5 setting is deleted when it is uninstalled.
• Before starting uninstalling, check the following items.
∗
∗
∗
∗
∗
1
RasterLinkPro5 is not running.
The RasterLinkPro5 license is deactivated.
The RasterLinkPro5 hot folder is not open (including via the network).
The RasterLinkPro5 printer is not being used (including via the network).
The RasterLinkPro5 hot folder and printer is not being mounted from Macintosh clients
with a Macintosh network connection tool (such as PC MACLAN and SMB).
Double click “Programs and Features” in [Control Panel].
Double-click “Add and Remove Programs”,
depending on the OS of the RasterLinkPro5installed PC.
The [Programs and Features] window
opens.
2
Double Click
From the “Currently installed programs:” list, select “Mimaki Raster
Link Pro5”.
Click Uninstall .
Click Remove depending on the OS of
the RasterLinkPro5-installed PC.
The “Programs and Features” confirmation
dialog box opens.
64
Click
Uninstall RasterLinkPro5
3
Uninstallation starts.
Yes
Click
.
Click
4
If the license is still active, a screen
for deactivating the license appears.
Before installing on another
PC, be sure to deactivate the
license of the PC on which the
license is activated.
If not deactivated, you cannot
activate the license with the
PC and cannot use the PC,
even if installing
RasterLinkPro5.
65
If PCMACLAN is installed on
the computer for
RasterLinkPro5, the right
warning message may be displayed during the uninstall.
OK
Click
to stop the
server.The computer is not
shutdown.
The right message may be
displayed during un-installation. In this case, delete the
installation folder manually
after un-installation.
5
The right dialog is displayed after a
completion of un-installation.
Click
Yes
and restart.
Click
• If PC MACLAN is used, it is required to execute [Remove folder information]
of PC MACLAN file server after the uninstallation of the RasterLinkPro5.
For details, see the following in the PC MACLAN User's Guide:
Using the File Server.................. Remove folder information
• When you create the “Work Folder” in any place other than the installation
folder of the RasterLinkPro5, delete the work folder after the restart.
• Make sure the following folders are not remained when you wish to reinstall
after un-installation of the RasterLinkPro5.
∗ Previous installation folder
∗ Previous work folder
When the above two folders are still remained, delete them before you start
reinstallation.
The RasterLinkPro5 may not start normally, if you do not delete the folders.
66
If an error occurs in license authentication
If an error occurs in license authentication
The countermeasure when an error occurs in license authentication is explained by following
the examples below:
Example 1 : RasterLinkPro5 was uninstalled without releasing license authentication.
Example 2 : OS was reinstalled without releasing license authentication.
Example 3 : HDD with OS was replaced without releasing license authentication.
You can conduct license authentication for the PC on which you conducted license authentication once as many times as you want until you release it and conduct license authentication
with the serial key used for other PC.
When you reuse RasterLinkPro5 in that PC
(1) Reinstall RasterLinkPro5.
(2) Start license authentication and input the same serial key.
• License authentication is conducted again.
When you use RasterLinkPro5 in other PC
(1) Release license authentication (
P.68) from the Web site and release license
authentication.
(2) Install RasterLinkPro5 into the PC on which you use RasterLinkPro5.
(3) Start license authentication and input the serial key released in (1).
Example 4 : PC was replaced without releasing license authentication.
Release license authentication (
P.68) from the Web site and release license authentication.
Example 5 : After having sent PC to repair, program update and profile update became
unavailable with an error displayed.
When it was repaired, it is possible that the device that is the base of PC unique information
gained at license authentication was replaced.
In such a case, it is necessary to conduct license authentication again. By following the procedures below, conduct license authentication.
(1) Release license authentication (
P.68) from the Web site and release license
authentication.
(2) Start RasterLinkPro5 in RasterLinkPro5 PC on which the error occurred.
(3) Conduct license authentication again.
67
Example 6 : The serial key was lost.
When RasterLinkPro5 was uninstalled without releasing license
authentication
In such a case, serial key information remains in the PC. When you reinstall RasterLinkPro5
and start license authentication, the serial key you input the previous time is displayed on the
serial key input screen.
You found that you lost the serial key after releasing license authentication.
In such a case, if you uncheck the checkbox of “Delete the serial key information.” on the first
screen when releasing license authentication, serial key information remains in the PC. The
checkbox is OFF by default.
Check that the serial key you input the previous time is displayed on the serial key input
screen.
How to release license authentication when PC has broken
down
If normal release of license authentication cannot be conducted (
P.56) and RasterLinkPro5
cannot be used in other PC, you can release license authentication in the procedures below:
• Do not use this function when normal release of license authentication can
be conducted. If you use this function, defects may occur in the following
license authentication etc. and RasterLinkPro5 cannot operate normally.
1
Start the Web browser and input the address below.
2
Input the authenticated serial key into
the serial key input form.
http://miws.mimaki.jp/license/agencytop.aspx
Click [RasterLink Deactivation (When the PC is broken)].
Click [Deactivation].
Then, license authentication is released.
68
If an error occurs in license authentication
MEMO
69
70
71
D202025-19-17122018
Printed in Japan
© 2015 MIMAKI ENGINEERING CO., LTD. All rights reserved.
HK
SW : 4.80
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement