Peavey AMD Mixer Owner Manual

Peavey AMD Mixer Owner Manual
 A Intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure
that may be of sufficient magnitude to constitute a risk of electric shock to persons.
ú Intended to alert the user to the presence of important operating and maintenance (servicing) instruc-
tions in the literature accompanying the product.
CAUTION Risk of electrical shock — DO NOT OPEN!
CAUTION To reduce the risk of electric shock, do not remove cover. No user serviceable parts inside. Refer
servicing to qualified service personnel.
WARNING To prevent electrical shock or fire hazard, do not expose this appliance to rain or moisture. Before
using this appliance, read the operating guide for further warnings.
A Este símbolo tiene el propósito de alertar al usuario de la presencia de “(voltaje) peligroso” que no tiene
aislamiento dentro de la caja del producto que puede tener una magnitud suficiente como para constituir
riesgo de corricntazo.
A Este símbolo tiene el propósito de alertar al usuario de la presencia de instrucciones importantes sobre
la operación y mantenimiento en la literatura que viene con el producto.
PRECAUCION Riesgo de corrientazo — No abra.
PRECAUCIÓN Para disminuír el riesgo de corrientazo, no abra la cubierta. No hay piezas adentro que el usuario
pueda reparar. Deje todo mantenimiento a los técnicos calificados.
ADVERTENCIA Para evitar corrientazos o peligro de incendio, no deje expuesto a la lluvia o humedad este aparato.
Antes de usar este aparato, lea más advertencias en la guía de operación.
4 Ce symbole est utilisé pour indiquer à l’utilisateur la présence à l’intérieur de ce produit de tension non-
isolée dangereuse pouvant être d’intensité suffisante pour constituer un risque de choc électrique.
Ce symbole est utilisé pour indiquer à l’utilisateur qu’il ou qu’elle trouvera d'importantes instructions
sur l’utilisation et l’entretien (service) de l’appareil dans la littérature accompagnant le produit.
ATTENTION Risques de choc électrique — NE PAS OUVRIR!
ATTENTION Afin de réduire le risque de choc électrique, ne pas enlever le couvercle. Il ne se trouve à l’intérieur
aucune pièce pouvant être réparée par l’utilisateur. Confier l’entretien à un personnel qualifié.
AVERTISSEMENT Afin de prévenir les risques de décharge électrique ou de feu, n’exposez pas cet appareil
à la pluie ou à l’humidité. Avant d’utiliser cet appareil, lisez les avertissements supplémentaires situés dans le guide
d’utilisation.
A Dieses Symbol soll den Anwender vor unisolierten gefáhrlichen Spannungen innerhalb des Geháuses
warnen, die von Ausreichender Stárke sind, um einen elektrischen Schlag verursachen zu kónnen.
Dieses Symbol soll den Benutzer auf wichtige Instruktionen in der Bedienungsanleitung aufmerksam
machen, die Handhabung und Wartung des Produkts betreffen.
VORSICHT Risiko — Elektrischer Schlag! Nicht óffnen!
VORSICHT Um das Risiko eines elektrischen Schlages zu vermeiden, nicht die Abdeckung enfernen. Es befinden
sich keine Teile darin, die vom Anwender repariert werden könnten. Reparaturen nur von qualifiziertem Fachper-
sonal durchführen lassen.
ACHTUNG Um einen elektrischen Schlag oder Feuergefahr zu vermeiden, sollte dieses Gerät nicht dem Regen
oder Feuchtigkeit ausgesetzt werden. Vor Inbetriebnahme unbedingt die Bedienungsanleitung lesen.
AMD 1220
12 x 2 MIXER
+
8
.
+
e
=
m
“$
+
=
=
®
ARCHITECTURAL ACCUTICE 5
MADE IN USA.
.
o
ой
>
o
.
o
ой
q
=
o
o
6
о
o
-
un
>
.
#
LIMIT
FAN di O&O OD
LEFT RIGHT
CHANNELS
GAIN (1)
Varies the gain of the channel input stage to allow a wide input dynamic range. Proper adjustment of the
input gain 1s aided by observance of the LIMIT LED.
HIGH (2)
An active tone control (shelving type, £15 dB) that varies the high frequency boost or cut.
MID FREQUENCY (3)
The (inner) "MID" is an active control capable of 15 dB of boost or cut at the center frequency selected by
the (outer) "FREQUENCY" control. Frequency range is variable from 200 Hz to 5 kHz.
LOW (4)
An active tone control (shelving type, +15 dB) that varies the low frequency boost or cut.
AUX A (5)
Used to adjust the level of signal sent from the channel to the AUX A mix. The signal at this point is PRE the
EQ and channel tader, and is controlled by the AUX A send and input gain control. May be used as a
monitor send control.
AUX B (6)
Used to adjust the level of signal sent from the channel to the AUX B mix. The signal at this point is PRE the
EQ and channel fader, and 1s controlled by the AUX B send and input gain control. May be used as a
monitor send control.
AUX C (7)
Used to adjust the level of signal sent from the channel to the AUX C mix. The signal at this point is
determined by the INPUT GAIN (1)/AUX C LEVEL /and PRE/POST (9) switch. With the PRE/POST switch
in the "in" position, the action of this control 1s POST and the signal is affected by the EQ and channel
FADER. The "out" position is PRE and the signal is unaffected by the EQ or the channel FADER.
AUX D (8)
Used to adjust the level of signal sent from the channel to the AUX D mix. The signal at this point 1s
determined by the INPUT GAIN (1)/AUX D LEVEL /and PRE/POST (9) switch. With the PRE/POST
switch in the "in" position, the action of this control is POST and the signal is affected by the EQ and
channel FADER. The "out" position is PRE and the signal is unaffected by the EQ or the channel FADER.
(See operational note on AUX C and D PRE/POST switch number 9.)
AUX C AND D PRE/POST SWITCH (9)
Used to select the source of the AUX C and D Channel sends. When the PRE/POST switch is in the "in"
position, the AUX C and D sends are POST the EQ and channel FADER. In the “out” position, the AUX C
and D sends are PRE the EQ and channel fader.
NOTE: PRE operation is normal for stage monitor mix applications, and POST is normally used for effects/
signal processors. (See operational note.)
OPERATIONAL NOTE
Your new AMD 1220 mixing console offers exceptional AUX send capability from each channel. Overview
of AUX configuration: The send capability of AUX A and B is "fixed" PRE, and the send capability of
AUX E and Fis "fixed" POST. Stage monitor mix applications usually require "PRE" sends from the
console, and effects/signal processing applications normally require "post" sends from the console. Notice
we have labeled all channel send controls "AUX," indicating multi-use functionality. However, the AUX A
and B sends will most likely be used for monitor mixes and AUX E and F sends will most likely be used for
signal processing. There are two additional sends labeled AUX C and D, which are "SWITCHABLE" PRE
or POST. With the PRE/POST switch in the "out" position, AUX sends C and D are PRE. This configuration
offers four separate PRE monitor sends (AUX A, B, C, and D) and two separate Post Effect Sends (AUX E
and F). With the PRE/POST switch in the "in" position, AUX sends C and D are POST. This configuration
offers four separate POST effects sends (AUX C, D, E, and F), and two PRE monitor sends (AUX A and B).
AUX E (10)
Used to adjust the level of signal sent from the channel to the AUX E mix. The signal at this point is POST
the EQ and channel fader, and is controlled by the AUX E send, input gain control, EQ, and channel fader.
Should normally be used as an effects/signal processing send.
AUX F (11)
Used to adjust the level of signal sent from the channel to the AUX F mix. The signal at this point is POST
the EQ and channel fader, and is controlled by the AUX F send, input gain control, EQ, and channel fader.
Should normally be used as an effects/signal processing send.
PAN (12)
For stereo operation PAN is used to mix the channel to Left, Right, or in-between in the "stereo image.” For
Mono (2 x 1) operation PAN enables channel assignment to the Left or Right submasters.
LIMIT LED (13)
Indicates when the signal level in the channel is too high. It illuminates when the channel signal reaches
approximately +18 dBV.
PFL SWITCH (14)
Used to route a post EQ signal to the headphones for cueing purposes. The PFL system is active when the
switch is in the "in" position.
CHANNEL LEVEL SLIDER (15)
Determines the level of the channel. Calibration is in dB and level is variable from (co) -infinity (off) to
+10 dB. This should be operated near the "0 dB" (unity gain) indicator whenever possible to assure an
optimum balance between channel noise and headroom.
MASTER SECTION
MASTER SECTION
AUX RETURN SECTION
NOTE: There are four AUX returns provided for routing signals back into the master mix section. These
returns (A, B, C, and D) are totally independent of the AUX sends and AUX outputs.
AUX A RETURN
TO AUX A (16)
Allows the AUX A return to be assigned to the AUX A mix.
TO AUX B (17)
Allows the AUX A return to be assigned to the AUX B mix.
LEVEL (18)
When an outboard effects device is connected into the AUX A return jack, this control regulates the level of
the effect in the Left or Right mix. Must be used together with AUX A Pan.
PAN (19)
Allows the effects return signal to be assigned to Left Main, Right Main, or both.
AUX B RETURN
TO AUX A (20)
Allows the AUX B return to be assigned to the AUX A mix.
TO AUX B (21)
Allows the AUX B return to be assigned to the AUX B mix.
LEVEL (22)
When an outboard effects device is connected into the AUX B return jack, this control regulates the level of
the effect in the Left or Right mix. Must be used together with AUX B Pan.
PAN (23)
Allows the effects return signal to be assigned to Left Main, Right Main, or both.
AUX C RETURN (STEREO)
LEVEL (24)
When an outboard effects device is connected into the AUX C return jack, this control regulates the level of
the effect in the Left or Right mix. Must be used together with AUX C Pan.
NOTE: AUX C return jack is stereo. Stereo effects processors may be returned at this point. Stereo (RTS)
1/4" plug is required. When mono effects return signals are patched in at this point, stereo 1/4" plug must be
rewired with tip and ring connected.
PAN (25)
Allows the effects return signal to be assigned to Left Main, Right Main, or both.
AUX C RETURN (STEREO)
LEVEL (26)
When an outboard effects device is connected into the AUX D return jack, this control regulates the level of
the effect in the Left or Right mix. Must be used together with AUX D Pan.
NOTE: AUX D return jack is stereo. Stereo effects processors may be returned at this point. Stereo (RTS)
1/4" plug is required. When mono effects return signals are patched in at this point, stereo 1/4" plug must be
rewired with tip and ring connected.
PAN (27)
Allows the effects return signal to be assigned to Left Main, Right Main, or both.
PFL SWITCH (28)
Used to route a pre fader signal from the Left and Right outputs to the headphones for cueing purposes. The
PFL system is active when the switch is in the "in" position.
LED ARRAYS (29)
Two calibrated LED arrays are provided to visually indicate the levels of the LEFT and RIGHT outputs.
MASTER (30)
Controls the overall mix level when the mixer is operated in the mono configuration (2x1). "Master" 1s the
combination of the Main Left and Right signals and the Master AUX In.
HEADPHONE LEVEL (31)
Adjusts the Left and Right signal level to the headphone jack. Signal is taken pre the Left and Right main
sliders. (This control is active only when no PEL switches are engaged.)
PFL LEVEL (32)
Controls the level for any "pre fade listen" (PFL) source, selected on the mixer. One or more PFL switches
must be engaged before this control is active.
AUX MASTERS (A, B, C, D, E, and F) (33)
E»
©,
O,
WARNING: 10 REDUCE THE RISK OF FIRE OR
ELECTRIC SHOCK DO
0 WARNING |
DO NOT OPEN AVIS:RISQUE DE CHOC ELECTRIQUE-NE PAS QUVRIR.
120 VAC
60 Hz
30 WATTS
BALANCED OUTPUT —
AUX B AUX A RIGHT LEFT
OUT OUT 7 CUT OUT
PATCH (36)
This jack allows individual channel patching after the input GAIN control and before the channel
equalization. This stereo jack is wired so that if a phone plug is inserted to the first detent only, the send from
the channel will be accessed without interrupting the normal channel signal flow. If a stereo phone plug is
inserted fully into the jack, the channel "send" connects to the tip and the ring portion becomes the channel
"return." In this mode, normal channel signal flow is interrupted, and equipment connected via the stereo
phone plug is inserted in-line.
LOW Z MIC (37)
For use with low impedance microphones or low level sources equipped with an XLR connector.
LINE IN (38)
For use with high impedance microphones or high level sources equipped with a 1/4" phone plug.
AUX IN (39)
Auxiliary inputs are provided for each AUX mix. This input is used to connect line level signals to AUX
mix. The connector is a mono (TS) 1/4" phone jack. Tip is signal, sleeve is signal ground.
AUX OUTPUT (40)
Outputs are provided for each AUX mix. This output is used to connect the AUX mix output to external
devices using a mono (TS) 1/4" phone jack. Tip is signal, sleeve is signal ground.
AUX IN (41)
Auxiliary inputs are provided for the MASTER, LEFT, and RIGHT mixes. This input is used to connect line
level signals directly to the MASTER mix, LEFT mix, or the RIGHT mix. The connector is a mono 1/4"
(TS) phone jack. Tip is signal, sleeve is signal ground.
RETURN (42)
Four returns are provided (A, B, C, and D). Used to connect line level signals to the AUX RETURN. Signal
at this point may be routed to LEFT or RIGHT masters with AUX RETURN level and pan controls (18),
(19), (22), (23).
NOTE: AUX A and AUX B returns have the capability to route signal from the RETURN jack to AUX A
and AUX B mixes. The connector is a mono 1/4" (TS) phone jack. Tip is signal, sleeve 1s signal ground.
OUTPUT (43)
Outputs are provided for LEFT, RIGHT, and MASTER mixes. Used to connect the MIX output signal to
external devices. The connector is a mono 1/4" (TS) phone jack. Tip is signal, sleeve 1s signal ground.
NOTE: LEFT and RIGHT outputs are normally used for "stereo" or dual-output operation. The master
output is normally used for "mono" operation.
PHANTOM POWER SWITCH (44)
Selects phantom power for all channels. In the "off" position, no phantom powering is available on any
channels.
LINE CORD (120 V PRODUCTS ONLY) (45)
For your safety, we have incorporated a 3-wire line (mains) cable with proper grounding facilities. It is not
advisable to remove the ground pin under any circumstances. If it is necessary to use the equipment without
proper grounding facilities, suitable grounding adaptors should be used. Less noise and greatly reduced
shock hazard exist when the unit is operated with the proper grounded receptacles.
BALANCED LINE OUTPUT (46)
Provides 600 ohm, transformer balanced signal to be used as "direct" patch into mixing consoles, tape
recorders, etc. The signal at this point has been frequency compensated for low noise operation.
SPECIFICATIONS
All specifications are typical
unless otherwise noted and are
referenced to nominal output level
(0 dBV) unless otherwise noted.
All measurements are wideband
(20 Hz to 20 kHz) unless
otherwise stated.
0 dBV = | volt
O0 dBu = .778 volt
CHANNEL
EQUIVALENT INPUT NOISE:
-133 dBY (150 ohm, 25° C.,
60 dB Gain)
FREQUENCY RESPONSE:
+2 dB 20-20,000 Hz all EQ
flat
DISTORTION:
Less than .05% @ 0 dB
Output 60 dB Gain
Typical .003% @ 0 dB Output
30 dB Gain
(Mic input to L or R outputs,
EQ flat, Sliders at 0)
COMMON MODE REJECTION
RATIO (CMRR):
Greater than 100 dB typical
INPUT IMPEDANCE:
Mic = 2 kilohms
Line = 10 kilohms
Patch = 20 kilohms
OUTPUT IMPEDANCE:
Patch Send = 100 ohms
HIGH EQ:
+15 dB @ 10 kHz minimum
Center detent flat +2 dB
MID EQ:
+15 dB @ selected frequency
Center detent flat +2 dB
MID FREQUENCY:
200 Hz to 5 kHz adjustment of
mid frequency
LOW EQ:
+15 dB @ 50 Hz minimum
Center detent flat +2 dB
MAXIMUM PREAMP GAIN:
60 dB minimum
MINIMUM PREAMP GAIN:
2dB
MAXIMUM CHANNEL GAIN:
70 dB
(Pan at L or R, Slider @ Max,
EQ flat)
MAXIMUM INPUT LEVEL:
Mic = +16 dBV (6.3 V RMS)
Line = +36 dBV (60 V RMS)
Patch Return = +18 dBV
(8 V RMS)
MAXIMUM OUTPUT LEVEL:
Patch Send = +18 dBY
(8 V RMS)
NOMINAL INPUT LEVEL:
Mic = -20 dBV (100 mV,
-18 dBu)
Line = 0 dBV (1 Y RMS)
Patch Return = 0 dBV
(1.0 V RMS)
HEADROOM:
Nominal = 18 dBV
Red LED = 3 dBV
PAN CHARACTERISTICS:
2 dB down @ mid position
LED LEVEL:
Red = +15 dBV
(5.62 V RMS)
MASTER
LED METER CALIBRATION:
0 = 0 dBV (1.0 Y RMS)
NOMINAL OUTPUT LEVEL
UNBALANCED:
Master = +0 dBV
(1.0 V RMS)
L&R=+0dBV
(1.0 V RMS)
AUX A-F = +0 dBV
(1.0 V RMS)
NOMINAL OUTPUT LEVEL
BALANCED:
Master = +6 dBV
(2.0 V RMS)
L & R = +6 dBV (2.0 V RMS)
AUX À & B = +6 dBV
(2.0 V RMS)
NOMINAL HEADROOM:
Master = 19 dB (balanced and
unbalanced)
L & R = 19 dB (balanced and
unbalanced)
AUX A-F = 19 dB (balanced
and unbalanced)
MAXIMUM OUTPUT LEVEL
UNBALANCED:
Master = +19.5 dBV
(9.5 V RMS, +21.5 dBu)
L 8 R=+19.5 dBV (9.5 V
RMS, +21.5 dBu)
AUX А-Е = +19.5 dBV (9.5
V RMS, +21.5 dBu)
MAXIMUM OUTPUT LEVEL
BALANCED:
L&R-=+19.5 dBV (9.5 V
RMS, +21.5 dBu)
AUX À &B = +19.5 dBV
(9.5 V RMS, +21.5 dBu)
OUTPUT IMPEDANCE:
Master = 100 ohms
L & R = 100 ohms
(unbalanced)
600 ohms (balanced)
AUX A-F = 100 ohms
(unbalanced)
AUX A-B = 600 ohms
(balanced)
SPECIFICATIONS
(continued)
OUTPUT NOISE
AMD 1620
Residual: -97 dBV
(L&R sliders down)
Bus: -88 dBV
(All Channel Sliders down,
Effects Returns down, Pans at
middle)
Nominal: -82 dBV
(All channels at 30 dB Gain,
150 ohm input, EQ flat, Pans
at middle, Sliders at 0, All
assigns at L&R, Effects
Returns down)
AMD 1220
Residual: -97 dBV
(L&R sliders down)
Bus: -89 dBY
(All Channel Sliders down,
Effects Returns down, Pans at
middle)
Nominal: -84 dBV
(All channels at 30 dB Gain,
150 ohm input, EQ flat, Pans
at middle, Sliders at O, All
assigns at L&R, Effects
Returns down)
AUX A-D RETURN INPUT
IMPEDANCE:
33 kilohms
AUX A-D RETURN GAIN:
16.5 dB Max
AUXILIARY INPUT GAIN:
0 dB
(Master, L, R, AUX A-F)
PFL AUXILIARY:
Tip = PFL Signal @ 1 V RMS
Nominal
Ring = PFL Switch Signal
(Grounding Activates PFL)
HEADPHONE:
Stereo 8 ohms to 200 ohms
nominal
Tip = Left, Ring = Right,
Sleeve = Ground
500 mW Total Power
Less than 1% Distortion
POWER CONSUMPTION:
120 V AC 60 Hz, 30 watts
This block diagram shows signal flow within the unit. In order to thoroughly understand
the unit's functions, please study the block diagram carefully.
NOTE:
ALL CABLING BEFORE THE POWER AMP
SHOULD BE SHIELDED. OUTPUT OF POWER
MAY BE SPEAKER CABLES.
== AUX B- AUX A=
Signal Processor
IN OUT
PATCH
LOW 7 MIC
Hi Z Mic
Power
Amplifier
EROS
) MONAURAL SOUND SYSTEM
Siereo cae 7 .
Power
Amplifier
Signal Processor
(STEREO
— — IN UT}
Signal Processor
IN QUT
[ Power
Signal Processor Amplifier
QUT
Auxiliary MONITOR "A" MIX
Power
Amplifier
NOTE:
FOUR "POST" EFFECTS SENDS ARE POSSIBLE WITH AUX C
AND D SWITCH TO "POST." OUTPUT FROM SIGNAL |
PROCESSORS SHOULD PATCH INTO RETURNS A, B, C, AND D.
MONITOR "B" MIX
Provided below is a patching diagram to record
your own hookups for future reference.
PATCH
LOW Z MIC
LINE
IMPORTANT SAFETY INSTRUCTIONS
WARNING: When using electric products, basic cautions should always be followed, including the following.
1.
10.
11.
14.
15.
Read all safety and operting instructions before using this product.
All safety and operating instructions should be retained for future reference.
Obey all cautions in the operating instructions and on the back of the unit.
All operating instructions should be followed.
This product should not be used near water, i.e., a bathtub, sink, swimming pool, wet basement, etc.
This product should not be located so that its position does not interfere with its proper ventilation. It should not be placed flat against a wall or placed
in a built-in enclosure that will impede the flow of cooling air.
This product should not be placed near a source of heat such as a stove, radiator, or another heat producing amplifier.
Connect only to a power supply of the type marked on the unit adjacent to the power supply cord.
Never break off the ground pin on the power supply cord. For more information on grounding, write for our free booklet "Shock Hazard and
Grounding.”
Power supply cords should always be handled carefully. Never walk or place equipment on power supply cords. Periodically check cords for cuts or
signs of stress, especially at the plug and the point where the cord cxits the unit.
The power supply cord should be unplugged when the unit is 10 be unused for long periods of time.
If this product is to mounted in an equipment rack, rear support should be provided.
Metal parts can be cleaned with a damp rag. The vinyl covering used on some units can be cleaned with a damp rag, or an ammonia-based household
cleaner if necessary. Disconnect unit from power supply before cleaning.
Care should be taken so that objects do not fall and liquids are not spilled into the unit through the ventilation holes or any other openings.
This unit should be checked by a qualified service technician if:
a. The power supply cord or plug has been damaged.
b. Anything has fallen or been spilled into the unit.
c. The unit does not operate correctly.
d. The unit has been dropped or the enclosure damaged.
The user should not attempt to service this equipment. All service work should be done by a qualified service technician.
This product should be used only with a cart or stand that is recommended by Peavey Electronics.
Exposure to extremely high noise levels may cause a permanent hearing loss. Individuals vary considerably in susceptibility to noise induced hearing
loss, but nearly everyone will lose some hearing if exposcd to sufficiently intense noise for a sufficient time.
The U.S. Government's Occupational Safety and Health Administration (OSHA) has specified the following permissible noise level exposures.
Duration Per Day In Hours Sound Level dBA, Slow Response
8 90
6 92
4 95
3 97
2 100
11/2 102
1 105
1/2 110
1/4 or less 115
According to OSHA, any exposure in excess of the above permissible limits could result in some hearing loss.
Ear plugs or protectors in the ear canals or over the ears must be worn when operating this amplification system in order to prevent a permanent hearing loss
is exposure is in excess of the limits as set forth above. To ensure against potentially dangerous exposure to high sound pressure levels, it is recommended
that all persons exposed to equipment capable of producing high sound pressure levels such as this amplification system be protected by hearing protectors
while this unit is in operation.
SAVE THESE INSTRUCTIONS
THIS LIMITED WARRANTY VALID ONLY WHEN PURCHASED AND REGISTERED IN THE UNITED STATES OR CANADA. ALL EXPORTED PRODUCTS
ARE SUBJECT TO WARRANTY AND SERVICES TO BE SPECIFIED AND PROVIDED BY THE AUTHORIZED DISTRIBUTOR FOR EACH COUNTRY.
Ces clauses de garantie ne sont vaiables qu’aux Etats-Unis et au Canada. Dans tour les autres pays, les clauses de garantie et de maintenance sont
fixees par le distributeur national et assuree par lul seion la legislation envigueur.
Diese Garantie ist nur in den USA and Kanada gultig. Alle Export-Produkte sind der Garantie und dem Service des Importeurs des jewelligen Landes
unterworfen. Esta garantia es valida solamente cuando el producto es comprado en E.U. continentales o en Canada. Todos los productos que sean
comprados en el extranjero, estan sujetos a las garantias y servicio que cada distribuidor autorizado determine y ofrezca en los diferentes paises.
PEAVEY ONE-YEAR LIMITED
WARRANTY/REMEDY
PEAVEY ELECTRONICS CORPORATION (“PEAVEY”) warrants this product, EXCEPT for covers, footswitches, patchcords, tubes and meters, to be free from
defects in material and workmanship for a period of one (1) year from date of purchase, PROVIDED, however, that this limited warranty is extended only to the
original retail purchaser and is subject to the conditions, exclusions, and limitations hereinafter set forth:
PEAVEY 90-DAY LIMITED WARRANTY ON TUBES AND METERS
If this product contains tubes or meters, Peavey warrants the tubes or meters contained in the product to be free from defects in material and workmanship for
a period of ninety (80) days from date of purchase; PROVIDED, however, that this limited warranty is extended only to the original retail purchaser and is also
subject to the conditions, exclusions, and limitations hereinafter set forth.
CONDITIONS, EXCLUSIONS, AND LIMITATIONS OF LIMITED WARRANTIES
These limited warranties shall be void and of no effect, if:
a. The first purchase of the product is for the purpose of resale; or
b. The original retail purchase is not made from an AUTHORIZED PEAVEY DEALER; or
c. The product has been damaged by accident or unreasonable use, neglect, improper service or maintenance, or ather causes not arising out of defects in
material or workmanship, or
d. The serial number affixed to the product is altered, defaced, or removed.
In the event of a defect in materia! and/or workmanship covered by this limited warranty, Peavey will:
a. Inthe case of tubes or meters, replace the defective component without charge.
b. In other covered cases (i.e., cases involving anything other than covers, footswitches, patchcords, tubes or meters), repair the defect in material or
workmanship or replace the product, at Peavey's option; and provided, however, that, in any case, all costs of shipping, if necessary, are paid by you, the
purchaser.
THE WARRANTY REGISTRATION CARD SHOULD BE ACCURATELY COMPLETED AND MAILED TO AND RECEIVED BY PEAVEY WITHIN FOURTEEN (14)
DAYS FROM THE DATE OF YOUR PURCHASE.
In order to obtain service under these warranties, you must:
a. Bring the detective item to any PEAVEY AUTHORIZED DEALER or AUTHORIZED PEAVEY SERVICE CENTER and present therewith the ORIGINAL
PROOF OF PURCHASE supplied to you by the AUTHORIZED PEAVEY DEALER in connection with your purchase from him of this product.
if the DEALER or SERVICE CENTER is unable to provide the necessary warranty service you will be directed to the nearest other PEAVEY AUTHORIZED
DEALER or AUTHORIZED PEAVEY SERVICE CENTER which can provide such service.
OR
b. Ship the defective item, prepaid, to:
PEAVEY ELECTRONICS CORPORATION
International Service Center
326 Hwy. 11 & 80 East
MERIDIAN, MS 39301
including therewith a complete, detailed description of the problem, together with a legible copy of the original PROOF OF PURCHASE and a complete return
address. Upon Peavey's receipt of these items:
If the defect is remedial under these limited warranties and the other terms and conditions expressed herein have been complied with, Peavey will provide the
necessary warranty service to repair or replace the product and wili return it, FREIGHT COLLECT, to you, the purchaser.
Peavey's liability to the purchaser for damages from any cause whatsoever and regardless of the form of action, including negligence, is limited to the actual
damages up to the greater of $500.00 or an amount equal to the purchase price of the product that caused the damage or that is the subject of or is directly related
to the cause of action. Such purchase price will be that in effect for the specific product when the cause of action arose. This limitation of liability will not apply to
claims for personal injury or damage to real property or tangible personal property allegedly caused by Peavey's negligence. Peavey does not assume liability for
personal injury or property damage arising out of or caused by a non-Peavey alteration or attachment, nor does Peavey assume any responsbility for damage to
interconnected non-Peavey equipment that may result from the normal functioning and maintenance of the Peavey equipment.
UNDER NO CIRCUMSTANCES WILL PEAVEY BE LIABLE FOR ANY LOST PROFITS, LOST SAVINGS, ANY INCIDENTAL DAMAGES, OR ANY
CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE PRODUCT, EVEN IF PEAVEY HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES.
THESE LIMITED WARRANTIES ARE IN LIEU OF ANY AND ALL WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR USE; PROVIDED, HOWEVER, THAT IF THE OTHER TERMS AND
CONDITIONS NECESSARY TO THE EXISTENCE OF THE EXPRESSED, LIMITED WARRANTIES, AS HEREINABOVE STATED, HAVE BEEN COMPLIED
WITH, IMPLIED WARRANTIES ARE NOT DISCLAIMED DURING THE APPLICABLE ONE-YEAR OR NINETY-DAY PERIOD FROM DATE OF PURCHASE OF
THIS PRODUCT.
SOME STATES DO NOT ALLOW LIMITATION ON HOW LONG AN IMPLIED WARRANTY LASTS, OR THE EXCLUSION OR LIMITATION OF INCIDENTAL
OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU. THESE LIMITED WARRANTIES GIVE YOU
SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH MAY VARY FROM STATE TO STATE.
THESE LIMITED WARRANTIES ARE THE ONLY EXPRESSED WARRANTIES ON THIS PRODUCT, AND NO OTHER STATEMENT, REPRESENTATION,
WARRANTY, OR AGREEMENT BY ANY PERSON SHALL BE VALID OR BINDING UPON PEAVEY.
In the event of any modification or disclaimer of expressed or implied warranties, or any limitation of remedies, contained herein conflicts with applicable law,
then such modification, disclaimer or limitation, as the case may be, shail be deemed to be modified to the extent necessary to comply with such law.
Your remedies for breach of these warranties are limited to those remedies provided herein and Peavey Electronics Corporation gives this limited warranty only
with respect to equipment purchased in the United States of America.
INSTRUCTIONS — WARRANTY REGISTRATION CARD
1. Mail the completed WARRANTY REGISTRATION CARD to:
PEAVEY ELECTRONICS CORPORATION
POST OFFICE BOX 2898
MERIDIAN, MISSISSIPPI 39302-2898
a. Keep the PROOF OF PURCHASE. In the event warranty service is required during the warranty period, you will need this document. There will be no
identification card issued by Peavey Electronics Corporation.
2. IMPORTANCE OF WARRANTY REGISTRATION CARDS AND NOTIFICATION OF CHANGES OF ADDRESSES:
a. Completion and mailing of WARRANTY REGISTRATION CARDS — Should notification become necessary for any condition that may require correction,
the REGISTRATION CARD will help ensure that you are contacted and properly notified.
b. Notice of address changes — If you move from the address shown on the WARRANTY REGISTRATION CARD, you should notify Peavey of the change of
address so as to facilitate your receipt of any bulietins or other forms of notification which may become necessary in connection with any condition that may
require dissemination of information or correction.
3. You may contact Peavey directly by telephoning (601) 483-5365.
®
ARCHITECTURAL ACOUSTICS?
Features and specifications subject to change without notice.
Peavey Electronics Corporation 711 A Street / Meridian, MS 39302-2898 / U.S.A. / (601)483-5376 / Telex 504115 / Fax 486-1278
©1993 #80302034 Printed in U.S.A. 9/93
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement