OWNERS MANUAL
WARNING: TO PREVENT ELECTRICAL SHOCK OR FIRE HAZARD, DO NOT EXPOSE
THIS APPLIANCE TO RAIN OR MOISTURE. BEFORE USING THIS APPLIANCE,
READ THE OPERATING GUIDE FOR FURTHER WARNINGS, ——
G H ALIZATION LEAD GAIN VOICI ENTE REVERE = Г VE!
INPUTS NE a BRIGHT AU TE =a be i — 5 — ; ; TT = ет i, UNE 5 EFFECTS rr MADE IN ULSA. POWER
Cr amos | Ja 73 73 ha 73 a“ ts ‘Nia an | о ' IBACKSTAGE” fi}
| ® Y | y 2 E 2 az ва age BZ ES 9 9 y e 2 B 110 ene
Wo co; 1 9 0] 1 a 4 a à a a 4 a 12 12 12 12 = = 1 8 ins
HIGH LOW 0 10 0 16 CG 10 o 10 0 10 D 10-15 15+ =15 154 SEND RETURN 0 19 [mm] POWER
SAR GAIN LEVEL CHANNEL СОМ MID HIGH SUFERSAT POST = EDGE = LEVEL ‘
1 2 3 5 6 f 8 9 10 11 12 13 14 15
HIGH GAIN INPUT (1)
Used for most electric guitars. It is 6 dB louder than the Low Gain input.
LOW GAIN INPUT (2)
Provided for instruments that have extremely high outputs, which can result in overdriving (distorting) the High Gain
input. If both inputs are used simultaneously, the ouput levels are the same (both are Low Gain).
LEVEL (3)
Controls the volume level of the normal channel and is not affected by the SuperSat® or Post Gain controls.
BRIGHT SWITCH (4)
Provides a preset boost (+6 dB) to treble frequencies. To activate, depress the switch to its “in” position
CHANNEL SELECT SWITCH (5)
Allows selection of the lead or normal channel. The “in” position of the switch selects the lead channel and the “out”
position selects normal.
NOTE: Channel selection may also be accomplished by the remote footswitch. If remote selection is desired the channel
switch must be in the “in” (lead) position.
LOW, MID & HIGH EQ (6)
Passive tone controls that regulate the low, mid and high frequencies, respectively.
SUPERSAT® (7)
A transistor simulation of tube distortion {soft clipping). To activate the SuperSat® effect, lead channel must be activated.
POST GAIN (8)
Controls the overall volume level of the lead channel. The final level adjustment should be made after the desired sound
has been achieved.
BOTTOM (9)
An active tone control (shelving type +/- 15 dB) that varies the low frequency boost or cut. NOTE: This control is functional
on the lead channel only.
EDGE (10)
An active tone control (shelving type +/- 15 dB) that varies the high frequency boost or cut. NOTE: This control is
functional on the lead channel only.
EFFECTS SEND (11)
Output for supplying signals to external low-level effects or signal processing equipment.
EFFECTS RETURN (12)
Input for returning signals from external low-level effects or signal processing equipment.
MASTER REVERB (13)
Controls the overall reverb level.
POWER LED (14)
luminates when AC power is being supplied to the amp.
POWER SWITCH (15)
Depress the switch tothe “On” position. The red pilot light (LED) will illuminate indicating power is being supplied to the
unit.
HEADPHONE REMOTE
65 WATTS WARNING ® nel:
22,864 RMS TC PREVENT THE RISK OF FIRE AMD SHOCK HAZARD, B A C KSTAG E 1 1 0 A Ter
В оны CO NOT EXPOSE THIS APPLIGHCE ТО НАМ OR /4 = Co
MOISTURE. DO NOT REMOVE FROM CASE. NO USER MADE INU SA E A @
SERVICEABLE PARTS INSIDE. REFER SERVICING TO DA
120 МАС QUALIFIED SERVICE FERSONNEL. A PRODUCT OF PEAVEY ELECTACNICS CORP ны
БО НЕ AVIS: RISQUE DE CHOC ELECTRIQUE - HE PAS MERICIAN MS
200 WATTS OUVRIR. PATENT PENDING
16 17 18
LINE CORD (16)
(120 V products only)
For your safety, we have incorporated a 3-wire line (mains) cable with proper grounding facilities. It is not advisable to
remove the ground pin under any circumstances. If it is necessary to use the equipment without proper grounding
facilities, suitable grounding adaptors should be used. Less noise and greatly reduced shock hazard exists when the unit
is operated with the proper grounded receptacles.
HEADPHONE OUT (17)
This stereo jack allows the signal to flow to both sides of any stereo headset. When headphones are connected to the
amplifier, the internal speaker is automatically turned off. NOTE: The headphone system will not work with headsets
equipped with a mono phone plug.
REMOTE SWITCH JACK (18)
Provided for the connection of the optional remote footswitch. Footswitch is used to select the Lead or Normal channels
and defeat reverb. When using remote footswitch always insert the plug fully (second click) to ensure proper operation.
BACKSTAGE® 110
SPECIFICATIONS
POWER AMPLIFIER SECTION: Nominal levels are with normal gain @ 5 HEADPHONE OUTPUT
RATED POWER & LOAD: Minimum levels are with normal gain @ 10 Load Impedance: 4 ohms or greater
65 W RMS into 8 ohms PREAMP HIGH GAIN INPUT Nominal Power Output: 100 mW into
POWER @ CLIPPING: (Typically) Impedance: High Z, 220K ohms 4 ohms
(5% THD, 1 kHz, 120V AC line) Nominal Input Level: -16 dBY, (Stereo jack, monaural signal,
65 W RMS into 8 ohms 150 mV RMS disconnects Ha speaker when phone
4 6 rme not recommeéndea Minimum Input Level: -34 dBV, plug is inserted)
20mV RMS SYSTEM HUM & NOISE @ NOMINAL
FREQUENCY RESPONSE Maximum Input Level: +10 dBV, 3V RMS INPUT LEVEL
+0, -2 dB 20 Hz ta 10 kHz H 20 kH iahted
@ 50 watts into 8 ohms PREAMP LOW GAIN INPUT (20 Hz io z unweighted)
TOTAL HARMONIC DISTORTION mpedaner ON ome EEC EEE
| than 0.3% 100 mW to 50 W RMS Nominal Input Level: -10 dBY, EQUALIZATION: (Normal Channel Only)
an édit 8 4 9 300 mV RMS Special Low, Mid & High passive type EQ
а Ея 4 Minimum Input Level: -28 dBV, Presence: +/- 15 dB @ 5 kHz, shelving
(typically below 0.2%) 40 mV RMS (active)
HUM & NOISE Maximum Input Level: +16 dBY, 6 Y RMS Push Bright: +6 dB (9 2 kHz
Greater than 78 dB below the rated power EFFECTS SEND VOICING: (Lead Channel Only)
POWER CONSUMPTION Load Impedance: 1K chms or greater Special Bottom & Edge active type EQ
EFFECTS RETURN Reverb Defeat (when reverb control is
PREAMP SECTION: Impedance: High Z, 22K ohms raised)
THE FOLLOWING SPECS ARE Designed Input Level: -10 dBV, 0.3V RMS Lead Channel Defeat (when selected with
MEASURED @ 1 kHZ WITH THE (Switching jack providing Effects Send to button)
CONTROLS PRESET AS FOLLOWS: Effects Return connection when not used)
Push Bright Off (Out)
Channel Select Normal (Out)
Low & High @ 10
Mid @ 0
SuperSat® & Post Gain @ 10
Bottom & Edge @ 0 dB
Reverb @ 0
SUPER GAIN
AMP post VOICING REVERB и
LEAD i. LEVEL Y
SWITCH
EFFECTS ale
BOT. EDGE
SWITCH SEND RETURN
SUPERSAT™
LOGIC —v VI
INPUT
je
PUSH HE ADPHONE
CHANNEL TONE
PREAMP
FT. SW. < < x
NORMAL LOW MID HIGH SPEAKER
LEVEL
PWR. AMP
PUSH
BRIGHT
This block diagram shows signal flow
within the unit. In order to thoroughly
understand the unit's functions, please
study the block diagram carefully.
TONE SETTING
Ня re BRIGHT E ON = Pm TD IA EFFECTS MENTRE
3 f a 3 E & 6 5 |B
2 B 2 EZ as 8% 9 o e
1 a 1 q 1 9 17 12 12 ig
Le 10 с 10 10 =15 5+ -15 15 + fi
LEVEL CHANNEL ae SUPEASAT POST BOTTOM EDGE SEND RETURN REL т
ADJUST TO CLEAN METAL ADJUST TO
TASTE TASTE
NORM, sn BRIGHT Ans EO BACH ey a AL Pr — Es REVERE
= 2 8
e 1 5
0 10 La) я y ü 10 |
ever CHANNEL en SUPERSAT FOST BOTTOM EDGE SEND RETURN LEVEL
ADJUST TO COUNTRY CLEAN COUNTRY ADJUST TO
TASTE LEAD TASTE
HERI 4 e авизнт 7 A Las E E EFFECTS |
3 7 5 7 3 7 E & 6 E = ry
> в ; he gd 4 1(@ OE
1 9 1 9 1 o 12 12 12 12 — E
о 10 io 10 0 10 =15 154 =15 15 =
LEVEL CHANNEL “an” “a” SUPEASAT* POST BOTTOM EDGE SEND RETURN Lever
ADJUST TO JAZZ MEDIUM DISTORTION ADJUST TO
TASTE TASTE
Tone settings given are general and will vary according to type of guitar, type and gauges of strings, type of pickup
and even type of pick. Personal taste, playing style, and type of music greatly contribute to desired tonality.
THIS LIMITED WARRANTY VALID ONLY WHEN PURCHASED AND REGISTERED IN THE UNITED STATES OR CANADA. ALL EXPORTED PRODUCTS ARE
SUBJECT TO WARRANTY AND SERVICES TO BE SPECIFIED AND PROVIDED BY THE AUTHORIZED DISTRIBUTOR FOR EACH COUNTRY!
Ces clauses de garantie ne sont vaiables qu'aux Etats-Unis et au Canada. Dans tous les autres pays, les clauses de garantie et de maintenance sont fixees par le
distributeur national et assuree par lul seion la legislation en vigueur.
Diese Garantie ist nur in den USA and Kanada gultig. Alle Export-Produkie sind der Garantie und dem Service des Importeurs des jewelligen Landes unterworfen.
Esta garantia es vallda solamente cuando el producto es comprado en E.U. continentales o en Canada. Todos los productos que sean comprados en el extranjero, estan
sujetos a las garantias y servicio que cada distribuidor autorizado determine y ofrezca en los diferentes paises.
PEAVEY ONE-YEAR LIMITED
WARRANTY/REMEDY
PEAVEY ELECTRONICS CORPORATION ("PEAVEY") warrants this product, EXCEPT for covers, footswitches, patchcords, tubes and meters, to be free from defects in material
and workmanship for a penod of one (1) year from date of purchase, PROVIDED, however that this limited warranty is extended only to the original retail purchaser and is subject to the
conditions, exclusions and limitations hereinafter set forth:
PEAVEY 90-DAY LIMITED WARRANTY ON TUBES AND METERS
If this product contains tubes or meters, Peavey warrants the tubes aor meters contained in the product to be free from defects in material and workmanship for a period of ninety (90)
days from date of purchase; PROVIDED, however, that this limited warranty is extended only to the original retail purchaser and is also subject to the conditions, exclusions and
limitations hereinafter set forth.
CONDITIONS, EXCLUSIONS AND LIMITATIONS OF LIMITED WARRANTIES
These limited warranties shall be void and of no effect if:
a. The first purchase of the product is for the purpose of resale; or
b. The original retail purchase is not made from an AUTHORIZED PEAVEY DEALER; ог
c, The product has been damaged by accident or unreasonable use, neglect, improper service or maintenance, or other causes not arising out of defects in material ar workmanship;
or
d. The serial number affixed to the product is altered, defaced or removed.
In the event of a defect in material and/or workmanship covered by this limited warranty, Peavey will;
a. In the case of tubes or meters, replace the defective component withaut charge,
b. In other covered cases (i.e. cases involving anything other than covers, footswitches, patchcords, tubes or meters), repair the defect in material or workmanship or replace the
product, at Peavey's option;
and provided, however, that, in any case, all costs of shipping, if necessary, are paid by you, the purchaser
THEWARRANTY REGISTRATION CARD SHOULD BEACCURATELY COMPLETED AND MAILED TO AND RECEIVED BY PEAVEY WITHIN FOURTEEN (14) DAYS FROM THE
DATE OF YOUR PURCHASE.
In order to obtain service under these warranties, you must:
a. Bring the defective item to any PEAVEY AUTHORIZED DEALER or AUTHORIZED PEAVEY SERVICE CENTER and present therewith the PERSONAL WARRANTY
IDENTIFICATION CARD along with the ORIGINAL FROOF OF PURCHASE supplied to you by the AUTHORIZED PEAVEY DEALER in connection with your purchase from him
of this product.
If the DEALER or SERVICE CENTER is unable to provide the necessary warranty service you will be directed to the nearest other FEAVEY AUTHORIZED DEALER or
AUTHORIZED PEAVEY SERVICE CENTER which can provide such service.
OR
b. Ship the defective item, prepaid, to
PEAVEY ELECTRONICS CORPORATION
711 “A” STREET
MERIDIAN, MS 39301
including therewith a complete, detailed description of the problem, together with your PERSONAL WARRANTY IDENTIFICATION CARD along with a legible copy of the
original PROOF OF PURCHASE, and a complete return address. Upon Peavey's receipt of the item:
Ifthe defectis remedial under these limited warranties and the other terms and conditions expressed herein have been complied with, Peavey will provide the necessary warranty
service to repair or replace the product and will return it, FREIGHT COLLECT, to vou, the purchaser.
Peavey's liability to the purchaser for damages from any cause whatsoever and regardless of the form of action, including negligence, is limited to the
actual damages up to the greater of $500.00 or an amount equal to the purchase price of the product that caused the damage or that is the subject of or is
directly related to the cause of action. Such purchase price will be that in effect for the specific product when the cause of action arose. This limitation of
liability will not apply to claims for personal injury or damage to real property or tangible personal property allegedly caused by Peavey’s negligence. Peavey
does not assume liability for personal injury or property damage arising out of or caused by a non-Peavey alteration or attachment, nor does Peavey assume
any responsibility for damage to interconnected non-Peavey equipment that may result from the normal functioning and maintenance of the Peavey
equipment.
UNDER NO CIRCUMSTANCES WILL PEAVEY BE LIABLE FOR ANY LOST PROFITS, LOST SAVINGS, ANY INCIDENTAL DAMAGES OR ANY
CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE PRODUCT, EVEN IF PEAVEY HAS BEEN ADVISED OF THE
FOSSIBILITY OF SUCH DAMAGES.
THESE LIMITED WARRANTIES ARE IN LIEU OF ANY AND ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR USE; PROVIDED, HOWEVER, THAT IF THE OTHER TERMS AND
CONDITIONS NECESSARY TO THE EXISTENCE OF THE EXPRESS, LIMITED WARRANTIES, AS HEREINABOVE STATED, HAVE BEEN COMPLIED
WITH, IMPLIED WARRANTIES ARE NOT DISCLAIMED DURING THE APPLICABLE ONE-YEAR OR NINETY-DAY PERIOD FROM DATE OF PURCHASE
OF THIS PRODUCT.
SOME STATES DO NOT ALLOW LIMITATION ON HOW LONG AN IMPLIED WARRANTY LASTS, OR THE EXCLUSION OR LIMITATION OF
INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU. THESE LIMITED
WARRANTIES GIVE YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH MAY VARY FROM STATE TO STATE,
THESE LIMITED WARRANTIES ARE THE ONLY EXPRESS WARRANTIES ON THIS PRODUCT, AND NO OTHER STATEMENT, REFRESENTATION,
WARRANTY OR AGREEMENT BY ANY PERSON SHALL BE VALID OR BINDING UPON PEAVEY.
In the event of any modification ar disclaimer of express or implied warranties, or any limitation of remedies, contained herein conflicts with applicable law,
then such modification, disclaimer or limitation, as the case may be, shall be deemed to be modified to the extent necessary to comply with such law.
Your remedies for breach of these warranties are limited to those remedies provided herein and Peavey Electronics Corporation gives this limited warranty
only with respect to equipment purchased in the United States of America.
INSTRUCTIONS — WARRANTY REGISTRATION CARD
1. Mail the completed WARRANTY REGISTRATION CARD to:
PEAVEY ELECTRONICS CORPORATION
POST OFFICE BOX 2898
MERIDIAN, MISSISSIPPI 39302-2898
a. Keepthe PERSONAL WARRANTY I.D. CARD along with your PROOF OF PURCHASE. In the event warranty service is required during the warranty
period, you will need these documents. There will be no other identification card issued by Peavey Electronics Corporation.
b. Defaced, mutilated or altered CARDS will not be honored
2 IMPORTANCE OF WARRANTY REGISTRATION CARDS AND NOTIFICATION OF CHANGES OF ADDRESS:
a. Completion and mailing of WARRANTY REGISTRATION CARDS — Should notification become necessary for any condition that may require
correction, the REGISTRATION CARD will help ensure that you are contacted and properly notified.
b. Notice of address changes — If you move from the address shown on the WARRANTY REGISTRATION CARD, you should notify Peavey of the
change of address so as to facilitate your receipt of any bulletins or other forms of notification which may become necessary in connection with any
condition that may require dissemination of information or correction.
3. You may contact Peavey directly by telephoning (601) 483-5365.
DANGER
EXPOSURE TO EXTREMEL Y HIGH NOISE LEVELS MÁY CALIGE A PERMANENT HEARING LOSS. IMDIVICUALS YARY CONSICERABL Y IN SUSCEPTIBILITY TO NOISE INDUCEDO HEARING LOSS. BUT NEARLY
EVERYONE WILL LOSE SOME HEARING IF EXPOSED TO SUFFICIENTLY INTENSE MOISE FOR A SUFFICIENT TIME
THEUS GOVERNMENT S OCCUPATIONAL SAFETY AND HEALTH ADMINISTRATION (OSMA) HAS SPECIFIED THE FOLLOWING PERMISSIBLE MOISE LEVEL EXPOSURES
DURATION PER DAY IN HOURS SOUND LEVEL dBA, SLOW RESPONSE
50 AO XD
E
1 119
less
ACCORDING Lea, ANY EXPOSURE IN EXCESS OF THE ABOVE LER poele LIMITS cou LD Cain LT IN ON ee Bo
ETERS IN THE EAR ÉS OR OVER TER
EEE GÉ-THE LIMITS AÉSÉTEORTH ABOVE 3
С DUCING HIE er
i
SONAL Е AY STRONG, uu
. Redal:
5
Lo
om
=
—il
‚| АН вай
= SEE
5 НОР
FIER HAS BEEN DESIGNED goss 3
NAL PEAK POWER ADEGUATER
a
meta 7 2 o
o mo should be ratified
Tor Tune reference,
. Dbeyall cautions in the operating instructions andon the
back ol the um.
Al operating instructions should be followed,
. This product should not be used near water ie a
bathtub. sink, swimming pool, wet basement. etc
. This product should be located so that its position does
not intertere with its proper ventilation |t should not be
placed flat against a wall or placed in a built-in enclosure
that will impede the flaw of coaling ar
This product should not be placed near a source of heat
such as a stove, radiator or another heal producing
amplifier
—
na
= я E
EA A he ground pin d aver supply
Information on groun
booklet "Shock Hazard and Grounding.”
. Power supply cords should always be handled carefully
Never walk ar place equipment on power supply cords.
Periodically check cords for cuts or signs of stress,
peca at the plug and the point where the cord axils
The unit
The power supply cord should be unplugged when the
UNItis to be unused for long periods af time.
If this product is to be mounted in an equipment rack, rear
suppor! should be provided.
ing write for our free
14.
15
Care should be taken so that objects de no fall and
liquids are not spilled into the unit through the ventilation
holes or any other openings.
This unit should be checked by a qualified service
technician if:
A, The power supply cord ar plug has been damaged.
B. Anything has fallen or been spilled into the umit
C. The unit does nol operate correctly.
0. The unit has been dropped or the enclosure damaged
Thé user should not to altempt 10 service trs equipment.
All service work should be done by a qualified service
technician.
Features and specifications subject to change without notice.
Peavey Electronics Corporation / 711 A Street / Meridian, MS 39302-2898 / U.S.A. / (601) 483-5365 Telex: 504115 / Fax: 484-4278
21988 Printed in the U.S.A 480300918 10/88
* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project
advertisement
© 2021