Lithium Ion Rechargeable Handle User`s Manual
719 Series Lithium Ion Handle
INTRODUCTION
Thank you for purchasing the Welch Allyn 719 Series Lithium Ion Power Handle. The
handle is intended for use as a power source for all Welch Allyn standard instrument
heads. The 719 series represents a new generation of handles from Welch Allyn. Taking
advantage of new battery technology, the 719 series provides you double the on-time in a
smaller and lighter weight package. Smarter battery technology means that “memory” is
no longer an issue. What’s more, the 719 reminds you to recharge with its low battery
indicator. The soft rheostat section provides a sure grip and the overall design is
ergonomically sound.
This handle is chargeable in the Welch Allyn Universal Charger. It is also chargeable in
the Welch Allyn 7111x (obsolete) Desk Charger and most standard 120V ophthalmic
stands with the use of a Welch Allyn Well Adapter (see 71980/90 Well Adapter User
Manual for manufacturer/model chart).
Before using this product, please read the following
warnings and instructions.
SAFETY AND WARNINGS
!
Attention: Read Operating Manual for Cautions and instructions
for use.
• POSSIBLE EXPLOSION HAZARD. Equipment not suitable for use in the presence of
a flammable anesthetic.
• Use the 719 Series Handle only with Welch Allyn approved products and chargers.
• Welch Allyn p/n 71960 (Battery Section) is only suitable for use with the 719
series handle.
• Do not disassemble or modify the battery pack. There are no serviceable parts
inside.
• Do not attempt to directly solder to the battery pack.
• Do not attempt to connect the positive and negative terminals to each other, nor
to any other device.
• Do not charge battery pack in any environment where the temperature may
exceed 40°C (104° F) or fall below 0°C (32° F).
• Do not dispose of the battery section in fire or water. Do not puncture, incinerate
or subject to strong impact or shock.
• Do not immerse the battery pack in any liquid.
• Do not strike or throw the battery pack.
• Do not use a battery pack which appears deformed, leaking, corroded, or is
otherwise irregular.
• Handle a damaged or leaking battery with extreme care. If you come into contact
with the electrolyte, wash the exposed area with soap and water. If it contacts
the eye, flush the eye with water for 15 minutes. Seek medical attention
immediately.
• When discarding a battery pack, contact your local waste disposal service
provider regarding local restrictions on the disposal or recycling of batteries.
• To avoid the risk of fire, burns, or damage to your battery pack or lamp, do not
allow a metal object to touch across the battery contacts.
FOR BEST PERFORMANCE:
• Do not expose battery pack to storage temperatures above 50°C (122°F) or below
-20°C (-4°F).
• Do not discharge battery pack if the ambient temperature is above 60°C (140°F) or
below -20°C (-4°F).
719209-3 Rev. A
Avant d’installer le block-batterie, veuillez lire les
informations suivantes et les conserver pour
consultation ultérieure.
Antes de instalar la batería, lea por favor la siguiente
información y guárdela en lugar seguro para su
futura referencia:
Mise en garde
Advertencias
!
Attention, veuillez lire le manuel d’utilisation pour
les précautions à prendre et le mode d’emploi
• Utiliser uniquement avec des dispositifs et des chargeurs approuvés par Welch
Allyn.
• Consulter les manuels d’utilisation respectifs des dispositifs et des chargeurs
Welch Allyn pour des mise en garde et spécifications supplémentaires. Toutes les
informations contenues dans les manuels d’utilisation ont priorité sur ces
spécifications.
• Ne pas essayer de démonter ou de modifier le bloc-batterie. Il ne contient pas de
pièces réparables par l’utilisateur.
• Ne pas essayer de souder un autre dispositif directement au bloc-batterie.
• Ne pas essayer de raccorder les bornes positives et négatives l’une à l’autre, ni à
un autre dispositif.
• Ne pas charger, le bloc-batterie dans un lieu où la température ambiante risque
de dépasser 40°C ou de tomber en dessous de 0°C.
• Ne pas plonger le bloc-batterie dans de l’eau.
• Ne pas essayer d’ouvrir ou de percer le bloc-batterie.
• Ne pas cogner ni lancer le bloc-batterie.
• Ne pas utiliser un bloc-batterie qui présente une déformation, une fuite, de la
corrosion ou une anomalie quelconque.
• Si une fuite d’électrolyte du bloc-batterie entre en contact avec la peau ou les
yeux, rincer à grande eau et consulter immédiatement un médecin.
• Ne pas démonter la partie batterie. Elle ne contient aucune pièce réparable par
l’utilisateur.
• Ne pas jeter la partie batterie dans le feu ou dans l’eau. Ne pas perforer, incinérer
ni soumettre à un impact ou un choc puissant.
• Pour éviter les risques d’incendie, de brûlures ou d’endommagement du blocbatterie, ne laisser aucun objet métallique entrer en contact avec les bornes de la
batterie ou de l’ampoule.
• Manipuler une batterie endommagée ou présentant une fuite avec grande
prudence. En cas de contact avec l’électrolyte, laver la zone exposée à l’eau et au
savon. En cas de contact oculaire, rincer l’oeil à grande eau pendant 15 minutes et
consulter immédiatement un médecin.
• Lores de la mise au rebut d’un bloc-batterie, contacter le service de ramassage
d’ordures local pour se renseigner sur les restrictions locales portant sur la mise
au rebut ou le recyclage des batteries.
• Risque d’explosion. Ce dispositif ne doit pas être utilisé en présence
d’anesthésiques inflammables à l’air, à l’oxygène ou à l’acide nitreux.
• Ce dispositif n’est pas étanche. Ne pas utiliser ni conserver de liquides au-dessus
ou sur la source de lumière.
• Pour prolonger la durée de service, débrancher la poignée et le module de charge
de la prise de courant une fois la recharge terminée. Ne pas laisser le module de
charge branché sur la prise courant sans poignée attachée.
POUR DES RÉSULTATS OPTIMUM:
• Ne pas entreposer le bloc-batterie à une température ambiante supérieure à 50°C
(122°F) ou inférieure à -20°C (-4°F).
• Ne pas décharger le bloc-batterie si la température ambiante est supérieure à
60°C (140°F) ou inférieure à -20°C (-4°F).
!
Atencion: Lea el Manual de Operación para obtener
precauciones e instrucciones de uso.
• POSIBLE RIESGO DE EXPLOSION. Este equipo no es compatible para su uso en
presencia de anestésicos inflamables.
• Utilice el Mango Serie 719 sólo cargadores y productos autorizados por Welch
Allyn.
• Parte No. 71960 de Welch Allyn (sección de la batería) es compatible sólo con los
Mangos de la Serie 719.
• No desarme la batería. Esta no contiene piezas que el usuario pueda reparar.
• No intente soldar directamente a la batería.
• No intente conectar el terminal positivo al negativo ni estos a ningún otro
dispositivo.
• No cargue la batería en ningún lugar con temperaturas que excedan los 40°C
(104°F) o que estén debajo de los 0°C (32°F).
• No deseche la batería en fuego o agua. No la perfore, incinere ni someta la
batería a un impacto o golpe fuerte.
• No sumerja la batería en agua.
• No golpee ni arroje la batería.
• No utilice la batería si está deformada, corroída, con fugas o si presenta algún
otro tipo de defecto.
• Maneje con sumo cuidado baterías dañadas o con fugas. Si el electrolito de la
batería entra en contacto con la piel, lave la zona afectada con agua y jabón. Si
entra en contacto con los ojos, enjuáguelos con agua durante 15 minutos y llame
inmediatamente al médico.
• Al desechar una batería, llame al servicio de recojo de basuras local para
informarse de las normas y restricciones locales para el desecho o reciclamiento
de baterías.
• Para evitar el riesgo de incendio, quemaduras o daños a la batería o lámpara, no
permita que ningún objeto de metal toque los contactos de la batería.
PARA MEJORES RESULTADOS:
• No almacene la batería en lugares donde las temperaturas sean mayores a 50°C
(122°F) o debajo de los -20°C (-4°F).
• No descargue la batería si la temperatura ambiente se encuentra sobre los 60°C
(140°F) o por debajo de los -20°C (-4°F).
SICHERHEITS- UND WARNHINWEISE
!
Achtung: Vorsichtshinweise und eine Gebrauchsanweisung
finden Sie in der Bedienungsanleitung.
• EXPLOSIONSGEFAHR. Gerät nicht in der Nähe entzündlicher Anästhetika
verwenden.
• Den Griff der Serie 719 nur mit von Welch Allyn zugelassenen Produkten und
Ladegeräten verwenden.
• Suggestion: Den Batterieeinsatz, Welch Allyn Bestellnummer 71960, nur mit dem
Griff der Serie 719 verwenden.
• Die Batteriepackung nicht auseinandernehmen oder verändern. Im Innern
befinden sich keine vom Benutzer wartbaren Teile.
• Nicht versuchen, direkt auf der Batteriepackung zu löten.
• Nicht versuchen, die positiven und negative Pole miteinander oder mit anderen
Geräten zu verbinden.
• Die Batteriepackung nicht in Umgebungen mit möglichen Temperaturen von über
40 °C oder unter 0 °C aufladen.
• Den Batterieeinsatz nicht verbrennen oder in Wasser entsorgen. Nicht
durchstoßen, anzünden oder starken Schlägen bzw. Stößen aussetzen.
• Die Batteriepackung nicht in Flüssigkeiten eintauchen.
• Auf die Batteriepackung nicht schlagen und diese nicht werfen.
• Batteriepackungen nicht verwenden, wenn sie verformt, undicht oder korrodiert
erscheinen oder auf sonstige Weise beeinträchtigt sind.
• Mit beschädigten oder undichten Batterien äußerst vorsichtig umgehen. Bei
Kontakt mit der Batteriesäure den betroffenen Bereich mit Wasser und Seife
abwaschen. Bei Kontakt mit den Augen diese 15 Minuten lang mit Wasser
ausspülen. Sofort einen Arzt aufsuchen.
• Zum Entsorgen der Batteriepackung mit dem örtlichen Abfallentsorgungsdienst
Verbindung aufnehmen, um die geltenden Bestimmungen zum Entsorgen und
Recycling von Batterien zu erhalten.
• Um die Gefahr eines Brandes sowie von Verbrennungen oder Beschädigungen an
der Batteriepackung oder Lampe zu vermeiden, darauf achten, daß die
Batteriekontakte nicht mit Gegenständen aus Metall berührt werden.
FÜR OPTIMALE LEISTUNG:
• Die Batteriepackung bei der Lagerung keinen Temperaturen von über 50 °C oder
unter -20°C aussetzen.
• Die Batteriepackung nicht entladen, wenn die Umgebungstemperatur über 60 °C
oder unter -20°C liegt.
AVVERTENZE E NOTE DI SICUREZZA
!
Attenzione: leggere il manuale operativo per disporre di avvisi
ed istruzioni riguardanti l'uso..
• POTENZIALE PERICOLO D'ESPLOSIONE. Apparecchiatura non adatta all'uso in
presenza di anestetici infiammabili.
• Utilizzare il manipolo serie 719 solo con prodotti e carica-batterie approvati dalla
Welch Allyn.
• Il p/n 71960 (sezione relativa alle batterie) della Welch Allyn è adatto all'uso solo
con il manipolo serie 719.
• Non disassemblare o modificare il pacco batteria, in quanto al suo interno non
sono presenti parti sottoponobili a manutenzione e/o riparazione.
• Evitare di eseguire saldature direttamente al pacco batteria.
• Evitare di collegare i morsetti negativi e positivi l'uno all'altro, o ad altri
dispositivi.
• Non caricare il pacco batteria in ambienti la cui temperatura possa superare i 40
oC (104O F) oppure essere inferiore ai 0 oC (32o F).
• Non gettare via la batteria nel fuoco o in acqua. Non perforare, incenerire od
esporla ad urti violenti o shock.
• Non immergere il pacco batteria in alcun liquido.
• Non urtare o gettare il pacco batteria.
• Non usare il pacco batteria nel caso in cui risulti deformato, presenti perdite, sia
corroso oppure abbia alte irregolarità.
• Le batterie danneggiate o con perdite devono essere maneggiate con estrema
attenzione. Se si dovesse venire in contatto con gli elettroliti, lavare la zona
esposta con sapone ed acqua. Se il contatto riguarda gli occhi, risciaquarli con
acqua per 15 minuti. Cercare assistenza medica immediatamente.
• Quando si getta via il pacco batteria, mettersi in contatto con il centro locale
responsabile dello smaltimento dei rifiuti per informazioni sullo smaltimento o il
riciclo delle batterie.
• Per evitare il rischio d'incendio, bruciature o danni al pacco batteria o alla
lampada, impedire che oggetti metallici vengano in contatto con i contatti della
batteria.
PER OTTENERE LA PRESTAZIONE MIGLIORE:
• Evitare di esporre il pacco batteria a temperature di immagazzinaggio superiori ai
50 oC (122O F) oppure inferiori ai -20 oC (-4o F).
• Non gettare via il pacco batteria se la temperatura ambiente è superiore ai 60 oC
(140O F) oppure inferiore ai -20 oC (-4o F).
Parts List
3.
Instrument
Head
Attachment
Light
Intensity
Control
Ring
Verify the Rheostat Section is secure on the Battery Section of the instrument
handle.
Rheostat
Section
Equipment Classification (All System Components)
Warranty
IXPO
Equipment not protected against the ingress of water.
Operating Mode:
Continuous Operation
The 719 series Power Handle is guaranteed by Welch Allyn against all manufacturing
defects. Welch Allyn will repair or replace, free of charge, any parts of its own
manufacture proven to be defective through causes other than misuse, neglect, damage
in shipment, or normal wear.
NOTE: This product complies with current required standards for electromagnetic
interference and should not present problems to other equipment or is affected by other
devices. As a precaution, avoid using this device in close proximity to other equipment.
Chrome Ring
Environment (All System Components)
On/Off
Button
Battery
Section
71960
Transport/Storage:
-20°C ~ 49°C, 95% R.H. Max, 500hPa - 1060hPa, Altitude
Operating:
10°C ~ 40°C, 95% R.H. Max, 500hPa - 1060hPa, Altitude
Figure 2
Low
Battery
Indicator
CLEANING
The cleaning of all Welch Allyn power handles and chargers is easily accomplished by
wiping the external surface with a cloth dampened with a mild detergent and water
solution, 70% isopropyl alcohol, or a 10% bleach solution (by volume). Do not immerse.
Figure 1
NOTE: Excess solution entering the assembly could damage internal components. Use
caution to ensure cloth is not saturated with solution.
OPERATING INSTRUCTIONS
Do not sterilize the 719 Series Power Handle or Well Adapter.
1.
Connect instrument head to the handle.
2.
Depress On/Off Button on Rheostat Section and rotate the Light Intensity Control
Ring clockwise (CW). To intensify light, continue to rotate until stop is reached
(Figure 1).
To turn off, rotate counter clockwise (CCW). Button will click when fully off. Turn
fully off after each use to ensure maximum on-time from the battery.
3.
Battery Recycling
Welch Allyn now employs the services of an agency which can disassemble and recycle
all components of rechargeable batteries so that nothing gets landfilled or incinerated.
Should you wish to dispose of your expended Welch Allyn rechargeable battery via
recycling (in the U.S. and Canada only), please send to:
Welch Allyn
RECYCLE BATTERY
4341 State Street Road
Skaneateles Falls, NY
13153-0220
CHARGING INSTRUCTIONS
7114x Universal Charger
1.
Insert the handle into the Well. Charge for 24 continuous hours to charge a dead
battery (less to top off).
2.
3.
Fully charged handles may remain in the Charger if desired.
Charging the Battery after partial discharge does not negatively affect overall
battery memory (unlike Ni-Cad cells).
71110 Desk Charger (obsolete) and Ophthalmic Stands
Welch Allyn Canada
RECYCLE BATTERY
160 Matheson Blvd. East
Mississauga, Ontario
CANADA L4Z 1V4
For locations outside the U.S. and Canada consult your local recycling authority for
correct disposal of batteries.
SPECIFICATIONS
See well adapter instructions for installing well adapter(s). Once adapters are installed,
follow charging procedures indicated under the 7114x Universal Charger.
(Specifications and design may change without notice)
NOTE: The Battery Section is not shipped fully charged. For maximum performance
charge the Battery Section for 24 hours when new or after a long period of inactivity.
Model Number:
71911
Dimensions:
5.4” Long x 1.125” Diameter (Max.)(137mm x 28.6 mm)
LOW BATTERY INDICATOR
Weight:
4.5 oz. (128 g)
1.
Typical Charge Time:
24 hours (fully discharged)
Typical Discharge Time:
110 minutes (for new battery)
2.
The Low Battery Indicator will illuminate several minutes before handle shuts off
depending on the age of the battery (Figure 1).
Once the battery is fully discharged, the Low Battery Indicator may flicker.
INSTALLING 71980 WELL ADAPTERS INTO THE 71110
DESK CHARGER
1.
2.
Insert the Well Adapter into one of the Handle Receptacles in the Desk Charger.
Be sure to insert the Adapter until it is fully seated. Once the Well Adapter has
been installed, it does not need to be removed (Figure 2).
One or two Well Adapters may be used with the Desk Charger.
Handle
Approvals:
US
Complies with: IEC 60601-1, CAN/CSA C22.2 No 125 and
UL544
When used with 71980 Well Adapter and 711 series
Desk Charger
Equipment Classification:
BATTERY REPLACEMENT
Removing the old Battery Section:
1.
Hold the instrument handle firmly by the Battery Section.
2.
Turn the Rheostat Section Counterclockwise until it detaches from the Battery
Section (see figure 2).
TYPE BF Equipment.
Equipment Classification (All Charger Model Numbers)
Installing A New Battery Section
1.
Insert the Rheostat Section into the new Battery Section.
2.
To connect the two sections, turn the Rheostat Section clockwise until tight (see
figure 2).
Double Insulation
The CE mark on this product indicates it has been tested to and
conforms with the provisions noted in the 93/42/EEC Medical Device
Directive.
Authorized European Representative:
European Regulatory Manager
Welch Allyn, Ltd.
Navan Business Park
Dublin Road
Navan, County Meath, Republic of Ireland
Telephone: 353 46 67700
Fax: 353 46 27128
SERVICE AND WARRANTY
Service Information
Other than battery replacement, this equipment contains no user servicable parts. Return
to a Welch Allyn authorized service center for service.
For Technical Support or to obtain return instructions, please contact your nearest Welch
Allyn service center listed below:
Welch Allyn, Inc.
4341 State Street Road
Skaneateles Falls, NY 13153-0220
Telephone: 800-535-6663
Fax: 315-685-4653
Welch Allyn, Ltd - Canada
160 Matheson Blvd. E., Unit #2
Mississauga, Canada L4Z 1V4
Telephone: 905-890-0004
Fax: 905-890-0008
Welch Allyn, Ltd. - UK
Cublington Road
Aston Abbotts
Buckinghamshire England HP22 4ND
Telephone: 011-0207-365-6780
Fax: 011-0207-365-9694
Welch Allyn, GmbH PSC
Zollerstrasse 2-4
D72417 Juningen, Germany
Telephone: 011-49-7477-927186
Fax: 011-49-7477-927293
Welch Allyn, LTD - Singapore
300 Beach Road
The Concourse #25-08
Singapore 199555
Telephone: 011-656-291-0882
Fax: 011-656-291-5780
Welch Allyn China Service Center
Room 708 Central Plaza
No. 277 Huang Pi Bei Rd.
Huang Pu District
Shanghai 20003, China
Telephone: 011-86-21-63279631
FAX: 011-86-21-63279632
Welch Allyn, Ltd. - Australia
The Metro Centre Unit 5
38-46 South Street
Rydalmere NSW 2116, Australia
Telephone: 011-(612) 9638-3000
Fax: 011-(612) 9638-3500
Welch Allyn warrants that the Welch Allyn 71960 Battery Section will perform to original
specifications during the two years from the date of manufacture, when used with the
Welch Allyn 719 series Power Handle. This warranty does not apply to the use of the
71960 battery in other products. A defective battery will be replaced if it fails within two
years of the date of manufacture.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising