Table of Contents www.HunterFan.com What to Expect with Your Installation Congratulations on purchasing your new Hunter® ceiling fan! It will provide comfort and performance in your home or office for many years. This installation and operation manual contains complete instructions for installing and operating your fan. Tools Needed Mounting Options 1.888.830.1326 Ceiling Bracket 30 inches Downrod ? 16 ? ? 17 PA G E 1 M0002-01 • 06/25/15 • © 2012–2015 Hunter Fan Company Troubleshooting PA G E 14 PA G E 13 Maintenance & Cleaning Light Kit PA G E PA G E 12 PA G E Switch Housing 11 Canopy 10 PA G E Blades 7 PA G E 6 Save your receipt for proof of purchase. Wiring 5 PA G E To register your fan, please visit: www.HunterFan.com/register 4 PA G E Preparation 3 PA G E Ladder PA G E We are proud of our work and appreciate the opportunity to supply you with the best ceiling fan available anywhere in the world. 2 PA G E 7 feet What to Expect with Your Installation www.HunterFan.com Read and Save These Instructions If you are unfamiliar with wiring, use a qualified electrician. This product conforms to UL Standard 507. WARNINGS 30 inches from blade tip to nearest wall or obstruction Must be able to secure the fan to building structure or fan-rated outlet box Know your wiring Ceiling angles greater than 34° will require an Angled Mounting Kit. See page 4 for details. Check box to see fan weight 7 feet from bottom edge of blade to the floor You may need a friend to help you. Assess location w.1 - To reduce the risk of fire, electrical shock, or personal injury, mount fan directly from building structure and/or an outlet box marked acceptable for fan support of 70 lbs (31.8 kg) and use the mounting screws provided with the outlet box. w.2 - To avoid possible electrical shock, before installing or servicing your fan, disconnect the power by turning off the circuit breakers to the outlet box and associated wall switch location. If you cannot lock the circuit breakers in the off position, securely fasten a prominent warning device, such as a tag, to the service panel. 1 Standard Downrod w.3 - To reduce the risk of fire, electrical shock, or motor damage, use only Hunter Solid State Speed Controls. 2 Shorter Downrod w.4 - To reduce the risk of personal injury, do not bend the blade brackets when installing the blade brackets, balancing the blades, or cleaning the fan. Do not insert foreign objects in between rotating fan blades. 3 for ceilings 8-10 feet high for fans installed close to ceiling Longer Downrod for ceilings 10 feet or higher CAUTIONS c.1 - All wiring must be in accordance with national and local electrical codes ANSI/NFPA 70. If you are unfamiliar with wiring, use a qualified electrician. c.2 - Use only Hunter replacement parts. Assess ceiling angle 1.888.830.1326 Select a downrod length 2 M0002-01 • 06/25/15 • © 2012–2015 Hunter Fan Company Tools Needed www.HunterFan.com Ladder Pliers Wire Strippers 9/64” Drill Bit (optional) Power Drill (optional) If mounting to a support structure, you will also need these tools. 3 M0002-01 • 06/25/15 • © 2012–2015 Hunter Fan Company Screwdrivers 1.888.830.1326 34O CEILING Mounting Options OPTION 1 If you have a flat ceiling: 1. You will need a longer downrod (sold separately). 2. If your ceiling angle is greater than 34°, you will also need an Angled Mounting Kit (sold separately). Angled Mounting Standard Mounting Style Ceiling Outlet Box (required) Use the three steps below to determine if your ceiling angle is greater than 34° 2 1 1.888.830.1326 Support Structure Support Structure OPTION 2 If you have an angled ceiling: Ceiling Outlet Box (required) Angled Mounting Style 3 34° PLACE FOLD against wall on dotted line Guide Touches BOTH Ceiling & Wall You need ONLY a Longer Downrod *most common SLIDE toward ceiling Guide Touches Wall but NOT Ceiling 2 ON SITUAT I 1 ON SITUAT I WALL Standard Mounting Hang your fan by a standard downrod (included). www.HunterFan.com Use Standard Mounting or Low-Profile Mounting to hang the fan from a flat ceiling. You need BOTH a Longer Downrod & an Angled Mounting Kit 4 M0002-01 • 06/25/15 • © 2012–2015 Hunter Fan Company Use Angled Mounting to hang the fan from a vaulted or angled ceiling. Ceiling Bracket www.HunterFan.com 1.888.830.1326 For angled ceilings, point opening toward peak. er w o nP r Tu OFF Use wood screws Use machine screws (included) when securing (provided with outlet to support structure with box) when securing to approved electrical outlet existing ceiling fan-rated box. Drill 9/64” pilot holes outlet box. Make sure in support structure to aid it is securely installed in securing ceiling bracket and is acceptable for fan with hardware found in support of 31.8 kg (70 lbs) the hardware bag. or less. Make sure all four (4) bumpers are still attached. To avoid possible electrical shock, before installing your fan, disconnect the power by turning off the circuit breakers to the outlet box associated with the wall switch location. If you are unable to do this, call Technical Support at 1-888-830-1326. Refer to warning w.1 on pg. 2 5 M0002-01 • 06/25/15 • © 2012–2015 Hunter Fan Company Ceiling Bracket (continued) Preparation www.HunterFan.com 1.888.830.1326 ! KEEP DISC D AR Time Saver Tip: Get a helper to insert grommets, found in the hardware bag, into the blades while you’re doing the next couple of steps. Remove the shipping blocks from the motor. Save the screws. They will be needed for blade iron installation. Note: Some fans will have a shipping ring instead of shipping blocks. Please remove the ring and save the screws. 6 M0002-01 • 06/25/15 • © 2012–2015 Hunter Fan Company Option 1 Downrod www.HunterFan.com 1.888.830.1326 skip to next page Standard Downrod for ceilings 8-10’ high Steps 1-5 to remove standard downrod pipe 1 2 4 Sold Separately Slide 3 10 9 8 Steps 6-10 to reassemble with new pipe 7 M0002-01 • 06/25/15 • © 2012–2015 Hunter Fan Company 5 Slide Option 3 Longer Downrod for angled ceilings or ceilings 10’ or higher Shorter Downrod for fans installed close to ceiling Included Option 2 Included (pre-assembled) If you need a different downrod length follow these steps: 7 6 Downrod (continued) KEEP! (not to scale) 8” & 3/8” 1.888.830.1326 STRIP CUT www.HunterFan.com ! KEEP Remove the pre-installed setscrew so that the downrod can be inserted. The wires can be cut, but leave at least 8” extending from the top of the downrod. Hand tighten the downrod (at least 4-5 full turns) until it stops. 8” Tighten the setscrew with pliers. DO NOT HAND TIGHTEN. 3/8” If the setscrew is not tightened securely, the fan may fall. 8 M0002-01 • 06/25/15 • © 2012–2015 Hunter Fan Company Downrod (continued) Put the wires and downrod through the canopy. Let the canopy sit loosely on top of the fan. www.HunterFan.com DO NOT PICK THE FAN UP BY THE CANOPY OR WIRES. Place the downrod ball into the slot in the ceiling bracket. 9 M0002-01 • 06/25/15 • © 2012–2015 Hunter Fan Company 1.888.830.1326 Wiring OM FR CEILIN www.HunterFan.com Note: To connect the wires, hold the bare metal leads together and place a wire connector over them, then twist clockwise until tight. G OM FR T KE Black FR (Ungrounded) M FA N Blue FRO (Ungrounded) AC Blue ING BR Black CEIL White M Using the orange wire connectors from the hardware bag, connect the black wire (ungrounded) from the ceiling to the black and the blue wires from the fan. Connect the white wire (grounded) from the ceiling to the white wire from the fan. Using orange wire connectors from the hardware bag, connect the white wire (grounded) from the ceiling to the white wire from the fan. Connect the black wire (ungrounded) from the ceiling to the black wire from the fan. Connect the second (ungrounded) wire from the ceiling to the blue wire from the fan. White Green/Yellow Stripe FR O For a Single Switch For Dual Switches (Grounded) Green/Yellow Stripe Using an orange wire connector from the hardware bag, connect the 3 grounding wires (green, green/ yellow stripe, or bare copper) coming from the ceiling, downrod, and hanging bracket. CEILIN OM G FR G (Ungrounded) (Grounded) (Grounding) OM FAN FR CEILIN 1.888.830.1326 O M FA N Turn the splices upward and push them carefully back through the hanger bracket into the outlet box. Spread the wires apart, with the grounded wires on one side of the outlet box and the ungrounded wires on the other side of the outlet box. Refer to CAUTION c.1 on pg. 2 10 M0002-01 • 06/25/15 • © 2012–2015 Hunter Fan Company Canopy www.HunterFan.com Screw Holes Position the canopy so that, when lifted into place, the canopy fits into the hanging bracket as shown. Lift the canopy into place so that the screw holes are aligned. Insert the two canopy screws found in the hardware bag. Note: Fan style may vary. 11 M0002-01 • 06/25/15 • © 2012–2015 Hunter Fan Company 1.888.830.1326 Blades www.HunterFan.com Remember the screws that you kept after removing the shipping blocks (page 6)? You need them plus five more from the hardware bag for this step. Insert grommets found in the hardware bag into the holes in the blades, then secure each blade to a blade iron with screws found in the hardware bag. Lightly attach the blade irons to the motor with screws found in the hardware bag, then securely tighten after both screws are attached. 12 M0002-01 • 06/25/15 • © 2012–2015 Hunter Fan Company 1.888.830.1326 Switch Housing Screw two housing assembly screws from the hardware bag halfway into the motor housing. It does not matter which two screw holes you choose. www.HunterFan.com Feed the wire plug through the center hole of the upper switch housing, then wrap keyhole slots around the screws and twist counterclockwise. 1.888.830.1326 Insert the third screw, found in the hardware bag, into place and then tighten all three screws. Make sure the upper switch housing is securely attached to the mounting plate. Failure to properly secure all 3 assembly screws could result in the switch housing fixture falling. 13 M0002-01 • 06/25/15 • © 2012–2015 Hunter Fan Company Light Kit www.HunterFan.com Switch Housing Screw Connect the plugs from the upper and lower switch housings. Make sure to line up the colored markings on the connectors. Want to install your fan without a light kit? Go to www.HunterFan.com/FAQs and click “How do I install my fan without the light kit?” 1.888.830.1326 Notch Partially install two of the switch housing screws found in the hardware bag. Align the notches in the sides of the lower switch housing with the screws on the upper switch housing. Twist the lower switch housing clockwise to lock into place. 14 M0002-01 • 06/25/15 • © 2012–2015 Hunter Fan Company Install the third switch housing screw. Tighten all three screws securely. Make sure the lower switch housing is securely attached to the upper switch housing. Failure to properly secure all three assembly screws could result in the light fixture falling. Light Kit (continued) www.HunterFan.com Light Pull Chain 1.888.830.1326 Fan Pull Chain Thumb Screw CONGRA T Shade To install the shade, first loosen the thumb screws. Raise the shade to the light fixture. Tighten all thumbscrews securely. YOU’REULATIONS! DONE! Bulb Install a bulb into each of the sockets. When necessary, replace with bulbs of the same type and wattage. Note: In compliance with US federal energy regulations, this ceiling fan contains a device that restricts its light output. Exceeding the wattage limit marked on the MAX wattage sticker affixed to the light socket(s) may result in fire hazard or improper operation. Connect the appropriate pull chain pendant to each of the short chains coming from the switch housing. See next page for fan operation instructions. Note: Glass shade style and number of lights may vary. 15 M0002-01 • 06/25/15 • © 2012–2015 Hunter Fan Company Maintenance & Cleaning www.HunterFan.com 1.888.830.1326 r we o nP r Tu ON Reverse Switch The fan pull chain controls the speed: from high to off. The light pull chain controls the light fixture: on and off. For questions regarding removing a light kit, call customer service 1-888-830-1326. To switch the direction of air flow, move the reverse switch to the opposite position. 16 M0002-01 • 06/25/15 • © 2012–2015 Hunter Fan Company For cleaning the fan, use soft brushes or cloths to prevent scratching. Cleaning products may damage the finishes. Troubleshooting www.HunterFan.com Fan doesn’t work Excessive wobbling Noisy Operation • Make sure power switch is on. • Tighten all of the blade and blade iron screws until they are snug. • Tighten the blade and blade iron screws until they are snug. • Pull the pull chain to make sure it is on. • Push the motor reversing switch firmly left or right to ensure that it is engaged. • Check the circuit breaker to ensure the power is turned on. • Make sure the blades spin freely. • Check to see if any of the blades are cracked. If so, replace all of the blades. • Turn the power off, support the fan carefully, and check that the hanger ball is properly seated. • Use the provided balancing kit and instructions to balance the fan. • Turn off power from the circuit breaker, then loosen the canopy and check all the connections according to the wiring diagram on page 10. • Check the plug connection in the switch housing. 17 M0002-01 • 06/25/15 • © 2012–2015 Hunter Fan Company 1.888.830.1326 Lights dim when turned on or do not turn on at all. • Make sure the wattage of the light bulbs installed matches the specifications on the light sockets.