Hunter Bayview Outdoor 54 inch Owners Manual

Hunter Bayview Outdoor 54 inch Owners Manual

1886

PB

Here is what comes in your box: We recommend that you pull everything out of the box and lay it out. We have grouped the drawn components below with the hardware you’ll need for those parts. The screws below are drawn to scale to make it easier to identify what piece of hardware is needed to install each component.

Hunter Pro Tip: Do not discard the hardware bags or mix parts from different bags. Make note of the symbol printed on each hardware bag. The symbols can be used to identify the appropriate hardware for each step.

1886

bag Washer x2 For installing the hanger bracket and wiring the fan Wood Screw x2 WIre Nut x4 Ceiling Bracket Canopy bag Canopy Screw x2 For installing the canopy bag Grommet x15 bag Blade Screw x15 For installing the blades Blade Arm bag x5 Blade Arm Screw Light Fixture bag

Spare Parts

For your convenience, you may receive extra fasteners.

KEEP DISCA RD

Remote

Remove the

ORANGE

shipping ring from the motor.

Save the screws. They will be needed for blade iron installation.

M0209-01 r020618 Bulb x3 Glass x3 For installing the light fixture

Find a part that is missing or damaged?

Don’t take it back to the store. Let us make it right. Visit us at HunterFan.com or call us at 1.888.830.1326.

2

1886

Choosing the Right Installation Location You probably bought this fan with a location in mind. Let’s check below to make sure it is a good fit.

Check the room dimensions: Check the outlet box: 30 inches from blade tip to nearest wall or obstruction You must be able to secure the fan to building structure or fan-rated outlet box.

7 feet from bottom edge of blade to the floor Standard Mounting Support Structure Checking the Ceiling Angle: Angled Mounting Support Structure Ceiling Outlet Box (required) Ceiling Outlet Box (required)

If you have a flat ceiling:

Hang your fan by a standard downrod. Some fans come with a shorter downrod for a Low Profile installation.

If you have an angled or vaulted ceiling:

1. You will need a longer downrod. (sold separately at HunterFan.com) 2. If your ceiling angle is greater than 34°, you will also need an Angled Mounting Kit. (Sold separately at HunterFan.com)

Angled Mounting A little more information on Angled Mounting:

For optimum performance and appearance, a longer downrod should be used with your Hunter ceiling fan when installing on high or angled ceiling. If your ceiling is angled greater than 34 sold separately at HunterFan.com

.

°

you will also need an Angled Mounting Kit. Longer downrods and the Angled Mounting Kit are Hunter Pro Tip: Determining if you need an Angled Mounting Kit:

Fold on the dotted line. Place against edge againts the wall. Slide towards the ceiling.

If the guide touches the wall but not the ceiling, you need an angled mounting kit.

3

34°

WALL

Installing the Ceiling Bracket

1886

Installing the Downrod

4

1886

3

Check the outlet box: Installing the Ceiling Bracket You have

two options

for installation. Pick which one works best for your location. Remove any existing bracket prior to installation.

Only use the provided Hunter ceiling bracket that came in your fan’s box.

Do this first!

Hunter Pro Tip: The machine screws are the ones that came with your outlet box.

1886

ow er

Option 1:

Machine Screws

Use machine screws

(provided with outlet box)

and washers when securing to existing ceiling fan-rated outlet box. Make sure it is securely installed and is acceptable for fan support of 31.8 kg (70 lbs) or less.

A NGL ED

MOUNTING TIP

For angled ceilings, point opening toward peak.

Option 2:

Wood Screws

Use wood screws and washers (included) when securing to support structure with approved electrical outlet box. Drill 9/64” pilot holes in support structure to aid in securing ceiling bracket with hardware found in the hardware bag.

bag Washer x2 x2 Wood Screw 1

Installing the Downrod Follow below if you are using the downrod that came pre-assembled in your box. Need to install a longer or shorter downrod? Check out the guide at the end of this manual.

Hunter Pro Tip: 2 The ground wire attached to the downrod is approximately 8 inches.

U T

3/8”

& ST

8” 3 Ceiling Bracket Remove the pre-installed setscrew so that the downrod can be inserted.

Downrod

KEEP!

Hanging Fan Wiring Tighten the setscrew with pliers.

DO NOT HAND TIGHTEN.

Pass all wires to one side of horizontal bar in downrod assembly. Hand tighten the downrod (at least 4–5 full turns) until it stops. Trim the wires coming from the fan so that 8-inches remain coming from the top of the downrod.

Canopy Blades Light

WARNING

FAN FALL HAZARD

To prevent SERIOUS INJURY or DEATH: • ALWAYS tighten setscrew with pliers.

• DO NOT hand tighten setscrew.

• CHECK the setscrew is tight using pliers each time you change fan direction.

Remote Troubleshooting 4

1886

an c op y o ve r d ow nrod

and w ires.

Progress Check:

Your fan should look like this.

Hanging the Fan

NOTICE

To prevent damage to fan, ALWAYS lift holding either the fan housing or the downrod.

Place the downrod ball into the slot in the ceiling bracket. 5 Ceiling Bracket Downrod Hanging Fan Wiring Canopy Blades Light Remote Troubleshooting

Wiring the Fan

1886

6

1886

5

Wiring the Fan We know wiring is hard. Let’s make it easier.

Follow these steps to get your fan wired quickly and safely. Follow the route below that best matches your wall switch setup. If you are unfamiliar with wiring or uncomfortable doing it yourself, please contact a qualified electrician.

You are going to need these: 4 Wire Nuts (these are in the bag)

Hunter Pro Tip:

Here is how to connect the wires:

Push the bare metal ends of the wires together and slide a wire nut over them. Then, twist the wire nut clockwise until tight.

Give it a gentle pull to make sure none of the wires are loose.

Have a single switch?

Follow these steps:

Connect the white (grounded) wire from the ceiling to the white wire from the fan.

White Grounded Connect the black (ungrounded) wire from the ceiling to the black wire from the fan.

Ungrounded Black Cap the blue wire from the fan. You will not need it for single switch wiring.

Blue Grounding e r G en /Ye l low Str ipe Green/Yellow Stripe bag Wire Nut x4 Connect the three grounding wires (green, green/yellow stripe, or bare copper) coming from the ceiling, downrod, and hanging bracket.

1886

WARNING

All wiring must be in accordance with national and local electrical codes ANSI/NFPA 70. If you are unfamiliar with wiring or in doubt, consult a qualified electrician.

Hunter Pro Tip:

Have extra wiring?

Turn the wires upward and push them carefully back through the hanger bracket into the outlet box. Make sure that the wires are still attached to the wire nuts.

Have dual switches?

Follow these steps:

Connect the white (grounded) wire from the ceiling to the white wire from the fan.

Connect the black (ungrounded) wire from the ceiling to the black wire from the fan.

White Grounded Ungrounded Black Blue Ung rounded (light) Connect the second ungrounded (light) wire from the ceiling to the blue wire from the fan.

Grounding e r G en /Ye l low Str ipe Green/Yellow Stripe bag Wire Nut x4 Connect the three grounding wires (green, green/yellow stripe, or bare copper) coming from the ceiling, downrod, and hanging bracket.

Ceiling Bracket Downrod Hanging Fan Wiring Canopy Blades Light Remote Troubleshooting 6

1886

Installing the Canopy

Insert the two canopy screws found in the hardware bag.

bag x2 Canopy Screw e c th an op y in pla ce as s hown.

Lift the canopy into place so that the screw holes are aligned. Insert grommets found in the hardware bag into the holes in the blades, then secure each blade to a blade arm with screws found in the hardware bag.

Installing the Blades:

bag x15 Blade Screw bag Grommet x15

Repeat x5

Lightly attach the blade arms to the motor with the blade arm screws, then securely tighten after both screws are attached.

KEEP!

DISCA RD

Remember the screws that you kept after removing the shipping blocks? You need them here.

bag x5 Blade Arm Screw

Repeat x5

7 Ceiling Bracket Downrod Hanging Fan Wiring Note: Fan style may vary.

Canopy Blades Light Remote Troubleshooting

Assembling the Light

1886

Installing the Bulbs and Glass

8

1886

7 Remove the cardboard plug guard before proceeding!

Connect the plugs from the fan and light fixture. Make sure to line up the colored markings on the connectors.

Assembling the Light

Push the connector and excess wire into the hole at the top of the light fixture.

IMPORTANT

The connector and excess wiring must be pushed into the light fixture in order to successfully mount the light fixture to the fan.

Raise the light kit to the bottom of the fan. Align the notch on the mounting ring on the top of the light kit with the pin in the mounting bracket on the bottom of the fan.

Notch Pin

1886

Some components not shown for visual clarity.

HOLD HERE

Need a little more help with assembling this light? Visit our light kit video at: http://bit.ly/HunterQuickConnect Installing the Bulbs and Glass

Hold the fan body stationary and rotate the light fixture clockwise to engage the locking pin.

Blade Arm Screw

Repeat x5 Repeat x3

Install a bulb into each of the sockets. When necessary, replace with bulbs of same wattage.

Hunter Pro Tip:

Want to install your fan without a light kit?

Go to www.HunterFan.com/FAQs and click “How do I install my fan without the light kit?” Ceiling Bracket Downrod Hanging Fan Wiring Canopy To install the shade, first loosen the thumb screws. Raise the shade to the light fixture. Tighten all thumbscrews securely. Blades ow

ON

er

WARNING

GLASS FALL HAZARD

To prevent SERIOUS INJURY or DEATH , make sure that glass is properly secured.

Light Remote Troubleshooting 8

1886

Installing the Remote Control Cradle You have two options for installing the remote cradle.

Choose which path works best for you.

Option 1: Using Adhesive Strip Option 2: Using Screws

Remove the cradle from the cradle bracket.

Separate the lining from the back of the adhesive strip on the cradle bracket.

Press the cradle bracket against the wall and hold firmly for 30 seconds.

Choose your cradle installation location.

If you are installing into drywall, drill two 9/64 width holes using the cradle bracket as a guide. Gently hammer the included drywall anchors into the pre-drilled holes.

Troubleshooting

Slide the cradle onto the mounted bracket.

Fan Doesn’t Work • Make sure power switch is on.

• Push the motor reversing switch firmly left or right to ensure that it is engaged.

• Check the circuit breaker to ensure the power is turned on.

• Make sure the blades spin freely.

• Turn off power from the circuit breaker, then loosen the canopy and check all the connections according to the wiring diagram.

• Check the plug connection in the switch housing.

Excessive Wobbling • Make sure the blades are properly installed on the blade iron posts.

• Turn the power off, support the fan carefully, and check that the hanger ball is properly seated.

• Use the provided balancing kit and instructions to balance the fan.

Remote Control of Fan is Erratic • Make sure the battery is installed correctly.

• Install a fresh battery.

Remote Only Works Close to Fan • Change battery.

Noisy Operation • Make sure the blades are properly installed.

• Check to see if any of the blades are cracked. If so, replace all of the blades.

Multiple Remote Issues • If you have multiple remotes or multiple remote controlled fans installed on the same circuit breaker and you are experiencing interference or faulty operation of your remote controls, please go to www.HunterFan.com/FAQs and click “How do I properly install multiple remote-controlled fans?” for information on how to correct this issue.

Hunter Pro Tip:

Cleaning the Fan

Use soft brushes or cloths to prevent scratching. Cleaning products may damage the finishes.

9 Ceiling Bracket Downrod Hanging Fan Wiring Canopy Blades Light Remote Troubleshooting 10

1886

1886

9

Troubleshooting Limited Lifetime Warranty

Hunter Fan Company grants this limited warranty to the original purchaser of this Hunter ceiling fan. This document can be found at www.HunterFan.com. Thank you for choosing Hunter!

How Can Warranty Service Be Obtained?

Proof of purchase is required

when requesting warranty service. The original purchaser must present a sales receipt or other document that establishes proof of purchase. Hunter, at its sole discretion, may accept a gift receipt. To obtain service, contact Hunter Fan Company online or by phone.

www.HunterFan.com/Support/Contact-Us/ 1-888-830-1326 Please do not ship your fan or any fan parts to Hunter. Delivery will be refused.

What Does This Warranty Cover?

Motor — Limited Lifetime Warranty

If any part of your ceiling fan motor fails during your ownership of the fan due to a defect in material or workmanship, as determined solely by Hunter, Hunter will provide you with a replacement fan free of charge.* The foregoing limited warranty applies only to the motor itself and does not apply to electronic controls – such as remote control transmitters, remote control receivers, or capacitors – used in conjunction with the motor. Such electronic control items are included in the one-year limited warranty below.

Other — One-Year Limited Warranty

Except as otherwise indicated throughout this warranty, if any part of your Hunter ceiling fan fails at any time within one year of the date of purchase due to a defect in material or workmanship, as determined solely by Hunter, Hunter will provide a replacement part free of charge.*

Light Kits — Warranty May Vary

Light kits are included in the one-year limited warranty. However, you may qualify for additional warranty coverage if your fan includes one of the following: •

LED Light Kits — Three-Year Limited Warranty

If your LED light kit module (not including glass components) or LED bulb fails at any time within three years of the date of purchase due to a defect in material or workmanship, as determined solely by Hunter, Hunter will provide a replacement part free of charge.* •

ENERGY STAR® Rated Light Kits — Three-Year Limited Warranty

If your ENERGY STAR rated light kit (not including glass components) fails at any time within three years of the date of purchase due to a defect in material or workmanship, as determined solely by Hunter, Hunter will provide a replacement light kit free of charge.*

* If no replacement product/part can be provided for your fan, we will provide a comparable or superior replacement product/part at the sole discretion of Hunter.

What Does This Warranty NOT Cover?

Labor Excluded. This warranty does not cover any costs or fees associated with the labor (including electrician’s fees) required to install, remove, or replace a fan or any fan parts. There is no warranty for light bulbs (except where otherwise noted); remote control batteries; fans purchased or installed outside the United States; fans owned by someone other than the original purchaser; fans for which proof of purchase has not been established; fans purchased from an unauthorized dealer; ordinary wear and tear; minor cosmetic blemishes; refurbished fans; and fans that are damaged due to any of the following: improper installation, misuse, abuse, improper care, failure to follow Hunter instructions, accidental damage caused by the fan owner or related parties, modifications to the fan, improper or incorrectly performed maintenance or repair, improper voltage supply or power surge, use of improper parts or accessories, failure to provide maintenance to the fan, or acts of God (e.g. flood). ORIGINAL PURCHASER’S SOLE AND EXCLUSIVE REMEDY FOR A CLAIM OF ANY KIND WITH RESPECT TO THIS PRODUCT SHALL BE THE REMEDIES SET FORTH HEREIN. HUNTER FAN COMPANY IS NOT RESPONSIBLE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, DUE TO PRODUCT FAILURE, WHETHER ARISING OUT OF BREACH OF WARRANTY, BREACH OF CONTRACT, OR OTHERWISE. Some States do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE APPLICABLE TO THIS PRODUCT ARE LIMITED IN DURATION TO THE PERIOD OF COVERAGE OF THE APPLICABLE LIMITED WARRANTIES SET FORTH ABOVE. Some States do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.

How Does State Law Affect Warranty Coverage?

This warranty gives you specific legal rights. You may also have other rights which vary from state to state.

Downrod If you need a different downrod length follow these steps:

1 2

Follow steps 1-5 to remove standard downrod pipe

3 4 5

1886

10 9 8

Follow steps 6-10 to reassemble with new downrod

7 6 10

Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement