Hunter Promenade Owners Manual

Hunter Promenade Owners Manual
Table of Contents
www.HunterFan.com
What to Expect with
Your Installation
Congratulations on purchasing your new Hunter® ceiling
fan! It will provide comfort and performance in your
home or office for many years. This installation and
operation manual contains complete instructions for
installing and operating your fan.
Tools Needed
Mounting Options
1.888.830.1326
Ceiling Bracket
30 inches
4
Downrod
Wiring
5
12
PA G E
3
PA G E
Preparation
Ladder
PA G E
To register your fan, please visit:
www.HunterFan.com/register
2
PA G E
7 feet
PA G E
We are proud of our work and appreciate the
opportunity to supply you with the best ceiling fan
available anywhere in the world.
Canopy
Save your receipt for proof of purchase.
Troubleshooting
?
?
?
20
PA G E
18
PA G E
1
M0130-01 • 10/04/16 • © 2016 Hunter Fan Company
17
Operation,
Maintenance & Cleaning
PA G E
15
PA G E
14
PA G E
PA G E
13
Remote Control
& Cradle
Light Kit
10
PA G E
Switch Housing
PA G E
Blades
7
PA G E
6
What to Expect with Your Installation
www.HunterFan.com
1.888.830.1326
Read and Save These Instructions
This product conforms to UL Standard 507.
WARNINGS
If you are unfamiliar
with wiring, use a
qualified electrician.
30 inches
from blade tip
to nearest wall
or obstruction
Must be able to
secure the fan to
building structure or
fan-rated outlet box
Know your wiring
You may need a
friend to help you.
Ceiling angles greater
than 34° will require an
Angled Mounting Kit.
See page 4 for details.
Check box to see
fan weight
7 feet
from bottom
edge of blade
to the floor
Assess ceiling angle
Assess location
1
Standard Downrod
2
Shorter Downrod
3
Longer Downrod
for ceilings 8-10 feet high
for fans installed close to ceiling
for ceilings 10 feet or higher
Select a downrod length
2
M0130-01 • 10/04/16 • © 2016 Hunter Fan Company
w.1 - To reduce the risk of fire, electrical shock, or personal injury,
mount fan directly from building structure and/or an outlet box marked
acceptable for fan support of 70 lbs (31.8 kg) and use the mounting
screws provided with the outlet box.
w.2 - To avoid possible electrical shock, before installing or servicing your
fan, disconnect the power by turning off the circuit breakers to the outlet
box and associated wall switch location. If you cannot lock the circuit
breakers in the off position, securely fasten a prominent warning device,
such as a tag, to the service panel.
w.3 - To reduce the risk of fire, electrical shock, or motor damage, use only
Hunter Solid State Speed Controls.
w.4 - To reduce the risk of personal injury, do not bend the blade brackets when
installing the blade brackets, balancing the blades, or cleaning the fan. Do not
insert foreign objects in between rotating fan blades.
CAUTIONS
c.1 - All wiring must be in accordance with national and local electrical codes
ANSI/NFPA 70. If you are unfamiliar with wiring, use a qualified electrician.
c.2 - Use only Hunter replacement parts.
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate
radio frequency energy and if not installed and used in accordance with the
instructions may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Caution: modifications not approved by the party responsible for compliance
could void user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference,
and (2) this device must accept any interference received, including
interference that may cause undesired operation.
Tools Needed
www.HunterFan.com
Ladder
Screwdrivers
Pliers
Power Drill
(optional)
Wire Strippers
9/64” Drill Bit
(optional)
If mounting to a support structure, you will also
need these tools.
3
M0130-01 • 10/04/16 • © 2016 Hunter Fan Company
Do not discard the
hardware bags or mix parts
from different bags. Make
note of the symbol printed
on each hardware bag.
The symbols can be used
to identify the appropriate
hardware for each step.
1.888.830.1326
34O
CEILING
Mounting Options
OPTION 1
If you have a flat ceiling:
1. You will need a longer downrod (sold separately).
2. If your ceiling angle is greater than 34°, you will
also need an Angled Mounting Kit (sold separately).
Angled
Mounting
Standard
Mounting
Style
Ceiling
Outlet Box
(required)
Use the three steps below to determine if your ceiling angle is greater than 34°
2
1
1.888.830.1326
Support
Structure
Support
Structure
OPTION 2
If you have an angled ceiling:
Ceiling
Outlet Box
(required)
Angled
Mounting
Style
3
34°
PLACE
FOLD
against wall
on dotted line
Guide Touches
BOTH Ceiling & Wall
You need ONLY
a Longer
Downrod
*most common
SLIDE
toward ceiling
Guide Touches Wall
but NOT Ceiling
2
ON
SITUAT
I
1
ON
SITUAT
I
WALL
Standard
Mounting
Hang your fan by a standard downrod (included).
www.HunterFan.com
Use Standard Mounting
or Low-Profile Mounting
to hang the fan from a flat ceiling.
You need BOTH
a Longer
Downrod &
an Angled
Mounting Kit
4
M0130-01 • 10/04/16 • © 2016 Hunter Fan Company
Use Angled Mounting
to hang the fan from a
vaulted or angled ceiling.
Ceiling Bracket
www.HunterFan.com
1.888.830.1326
r
we
o
nP
r
Tu
OFF
For angled ceilings, point
opening toward peak.
Use wood screws
Use machine screws
(included) when securing
(provided with outlet
to support structure with
box) when securing to
approved electrical outlet existing ceiling fan-rated
box. Drill 9/64” pilot holes
outlet box. Make sure
in support structure to aid
it is securely installed
in securing ceiling bracket and is acceptable for fan
with hardware found in support of 31.8 kg (70 lbs)
the
hardware bag.
or less.
Make sure all four bumpers are
still attached.
If you are unable to do this,
call Technical Support at
1-888-830-1326.
Refer to warning w.1 on pg. 2
5
M0130-01 • 10/04/16 • © 2016 Hunter Fan Company
To avoid possible electrical shock, before
installing your fan, disconnect the power by
turning off the circuit breakers to the outlet
box associated with the wall switch location.
Preparation
www.HunterFan.com
!
KEEP
DISC
D
AR
Time Saver Tip: Get a helper
to insert grommets, found in
the
hardware bag, into the
blades while you’re doing the
next couple of steps.
Remove the shipping blocks from the
motor. Save the screws. They will be
needed for blade iron installation.
Note: Some fans will have a shipping
ring instead of shipping blocks. Please
remove the ring and save the screws.
6
M0130-01 • 10/04/16 • © 2016 Hunter Fan Company
1.888.830.1326
Option 1
Downrod
www.HunterFan.com
1.888.830.1326
skip to next page
Standard
Downrod
for ceilings 8-10’ high
Steps 1-5 to remove standard downrod pipe
1
2
4
Sold Separately
Slide
3
10
9
8
Steps 6-10 to reassemble with new pipe
7
M0130-01 • 10/04/16 • © 2016 Hunter Fan Company
5
Slide
Option 3
Longer
Downrod
for angled
ceilings or
ceilings 10’ or
higher
Shorter
Downrod
for fans installed
close to ceiling
Included
Option 2
Included
(pre-assembled)
If you need a different downrod length follow these steps:
7
6
Downrod (continued)
KEEP!
(not to scale)
8”
&
3/8”
1.888.830.1326
STRIP
CUT
www.HunterFan.com
!
KEEP
Remove the pre-installed
setscrew so that the downrod
can be inserted.
The wires can be cut, but
leave at least 8” extending
from the top of the downrod.
Hand tighten the downrod (at
least 4-5 full turns) until it stops.
8”
Tighten the setscrew
with pliers. DO NOT
HAND TIGHTEN.
3/8”
If the setscrew is not tightened
securely, the fan may fall.
8
M0130-01 • 10/04/16 • © 2016 Hunter Fan Company
Downrod (continued)
Put the wires and downrod through
the canopy. Let the canopy sit loosely
on top of the fan.
www.HunterFan.com
DO NOT PICK THE FAN UP BY THE
CANOPY OR WIRES. Place the downrod
ball into the slot in the ceiling bracket.
9
M0130-01 • 10/04/16 • © 2016 Hunter Fan Company
1.888.830.1326
Wiring: Single Switch
www.HunterFan.com
1.888.830.1326
Dual Switch
Instructions
Have a single switch?
Follow these steps:
gro
Un
Grounded
White
ou
nd
ing
i pe
Str
Gr
Blue
Connect the black wire
(ungrounded) from the
ceiling to the black and the
blue wires from the fan.
ellow
Green/Y
Connect the white
(grounded) wire from
the ceiling to the white
wire from the fan.
un
ded
Grounded
Black
Green/Yellow Stripe
Connect the three
grounding wires (green,
green/yellow stripe, or
bare copper) coming from
the ceiling, downrod, and
hanging bracket.
Note: To connect the wires,
hold the bare metal leads
together and place a wire
connector over them, then
twist clockwise until tight.
Turn the splices upward and push them carefully back through the hanger bracket
into the outlet box. Spread the wires apart, with the grounded wires on one side of
the outlet box and the ungrounded wires on the other side of the outlet box.
Refer to CAUTION c.1 on pg. 2
10
M0130-01 • 10/04/16 • © 2016 Hunter Fan Company
Wiring: Dual Switch
www.HunterFan.com
1.888.830.1326
Have dual switches?
Follow these steps:
Grounded
ellow
Green/Y
Grounded
White
Gr
ou
Ungrounded
(lig
ht)
Black
ing
rou
nd
ed
Green/Yellow Stripe
Connect the three
grounding wires (green,
green/yellow stripe, or
bare copper) coming from
the ceiling, downrod, and
hanging bracket.
Un
g
Connect the black wire
(ungrounded) from the
ceiling to the black
wire from the fan.
nd
i pe
Str
Connect the white
(grounded) wire from
the ceiling to the white
wire from the fan.
Connect the second
ungrounded (light)
wire from the
celing to the blue
wire from the fan.
Note: To connect the wires,
hold the bare metal leads
together and place a wire
connector over them, then
twist clockwise until tight.
Blue
Turn the splices upward and push them carefully back through the hanger bracket
into the outlet box. Spread the wires apart, with the grounded wires on one side of
the outlet box and the ungrounded wires on the other side of the outlet box.
Refer to CAUTION c.1 on pg. 2
11
M0130-01 • 10/04/16 • © 2016 Hunter Fan Company
Canopy
www.HunterFan.com
Screw
Holes
Position the canopy so that, when
lifted into place, the canopy fits into
the hanging bracket as shown.
Lift the canopy into place so that
the screw holes are aligned.
Insert the two canopy screws
found in the
hardware bag.
Note: Fan style may vary.
12
M0130-01 • 10/04/16 • © 2016 Hunter Fan Company
1.888.830.1326
Blades
www.HunterFan.com
Remember the screws that
you kept after removing the
shipping blocks (page 6)? You
need them for this step.
Insert grommets found in the
hardware
bag into the holes in the blades, then
secure each blade to a blade iron with
screws found in the
hardware bag.
Lightly attach the blade irons to the
motor with the blade iron armature
screws, then securely tighten after both
screws are attached.
13
M0130-01 • 10/04/16 • © 2016 Hunter Fan Company
1.888.830.1326
Switch Housing
Screw two housing assembly screws
from the
hardware bag halfway into
the motor housing. It does not matter
which two screw holes you choose.
Note: Fan style and number of lights may vary.
www.HunterFan.com
Feed the wire plug through the center
hole of the upper switch housing, then
wrap keyhole slots around the screws and
twist counterclockwise.
14
M0130-01 • 10/04/16 • © 2016 Hunter Fan Company
1.888.830.1326
Insert the third screw, found in
the
hardware bag, into place and
then tighten all three screws.
Make sure the upper switch housing is securely
attached to the mounting plate. Failure to properly
secure all 3 assembly screws could result in the switch
housing fixture falling.
Light Kit
www.HunterFan.com
Switch
Housing
Screw
Connect the plugs from the upper and lower
switch housings. Make sure to line up the
colored markings on the connectors.
Want to install your fan without a light kit?
Go to www.HunterFan.com/FAQs and click
“How do I install my fan without the light kit?”
1.888.830.1326
Notch
Partially install two of the switch housing
screws found in the
hardware bag. Align
the notches in the sides of the lower switch
housing with the screws on the upper switch
housing. Twist the lower switch housing
clockwise to lock into place.
15
M0130-01 • 10/04/16 • © 2016 Hunter Fan Company
Install the third switch housing screw.
Tighten all three screws securely.
Make sure the lower switch housing is securely attached to
the upper switch housing. Failure to properly secure all three
assembly screws could result in the light fixture falling.
Light Kit (continued)
www.HunterFan.com
1.888.830.1326
Shade
Socket
Ring
Socket
Ring
Tool
Remove the socket rings from the
sockets. Install the shades onto
the sockets. Install the socket
rings onto the sockets. Tighten
them by turning clockwise with
the socket ring glass tool.
CONGRA
T
Bulb
Install a bulb into each of
the sockets. When necessary,
replace with bulbs of the same
type and wattage.
YOU’REULATIONS!
DONE!
See next page for fan
operation instructions.
Note: Fan style and number of lights may vary.
16
M0130-01 • 10/04/16 • © 2016 Hunter Fan Company
Remote Control
Battery
Door
www.HunterFan.com
1.888.830.1326
r
we
o
nP
r
Tu
ON
Phillips
Head
Screw
The remote transmitter is already paired to the
receiver and ready to use.
To access the battery compartment, remove
the small Phillips head screw that secures the
battery door to the transmitter assembly. The
battery should be installed with the positive
(+) side up. Replace with a CR2032 battery
when necessary.
Note: If your need to pair your remote, remove the battery
door. Cycle power to the fan by turning power off and back on
at the wall switch (or circuit breaker if necessary). Within three
minutes, press the pair button on the remote. If pairing was
successful, a single beep will sound. If three beeps sound, the
remote was unpaired. Re-pair using the steps above.
To prevent faulty operation, please disconnect power from
all other ceiling fans within range while pairing.
17
M0130-01 • 10/04/16 • © 2016 Hunter Fan Company
Remote Control Cradle
www.HunterFan.com
1.888.830.1326
You have two options to install the included remote control cradle
to the wall. Choose which path works best for you.
Option 1: Using Screws
Option 2: Using Adhesive Strip
Choose your cradle installation location.
Remove the cradle from
the cradle bracket.
If you are installing into drywall, drill two
9/64 width holes using the cradle bracket
as a guide. Gently hammer the included
drywall anchors into the pre-drilled holes.
Install the cradle bracket to the wall with
the included screws.
Slide the cradle onto the
mounted bracket.
Apply the adhesive sticker
to the back of cradle
bracket per the instructions
on the adhesive sticker.
18
M0130-01 • 10/04/16 • © 2016 Hunter Fan Company
Press the cradle bracket
against the wall and hold
firmly for 30 seconds.
Operation, Maintenance, and Cleaning
www.HunterFan.com
1.888.830.1326
Light
Button
Fan
Button
Fan
Control
Fan Operation:
Press and quickly release the fan button on the
remote control to turn the fan OFF or ON. Use the
fan control directional pad to raise or lower the fan
to the desired speed. Press and hold the fan button
to reverse the fan direction.
Light Operation:
Press and quickly release the light button on the
remote control to turn the light OFF or ON. Press
and hold the light button for continuous dim.
Cleaning the fan - use soft brushes or cloths
to prevent scratching. Cleaning products
may damage the finishes.
Slide the remote into the
cradle when not in use.
For questions regarding removing a light kit, call
customer service 1-888-830-1326.
19
M0130-01 • 10/04/16 • © 2016 Hunter Fan Company
Troubleshooting
www.HunterFan.com
Fan doesn’t work
Excessive wobbling
Noisy Operation
• Make sure power switch is on.
• Tighten all of the blade and
blade iron screws until they
are snug.
• Tighten the blade and blade
iron screws until they are snug.
• Pull the pull chain to make sure
it is on.
• Push the motor reversing switch
firmly left or right to ensure that
it is engaged.
• Check the circuit breaker to
ensure the power is turned on.
• Make sure the blades spin freely.
• Check to see if any of the
blades are cracked. If so, replace
all of the blades.
• Turn the power off, support
the fan carefully, and check
that the hanger ball is
properly seated.
• Use the provided balancing
kit and instructions to balance
the fan.
• Turn off power from the circuit
breaker, then loosen the canopy
and check all the connections
according to the wiring diagram
on pages 10-11.
Remote control of fan is erratic
• Check the plug connection in
the switch housing.
• Install a fresh battery.
If you have multiple remotes or
multiple remote-controlled fans
installed on the same circuit
breaker and you are experiencing
interference or faulty operation of
your remote controls, please go to
www.HunterFan.com/FAQs
and click “How do I properly install
multiple remote-controlled fans?”
for information on how to correct
this issue.
• Make sure the battery is
installed correctly.
20
M0130-01 • 10/04/16 • © 2016 Hunter Fan Company
1.888.830.1326
Lights dim when turned on or
do not turn on at all.
• Make sure the wattage of the
light bulbs installed matches
the specifications on the light
sockets.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement