This product conforms to UL Standard 507.
.1 - To reduce the risk of fire, electrical shock, or personal injury, mount fan directly from building structure and/or an outlet box marked acceptable for fan support of 70 lbs (31.8 kg) and use the mounting screws provided with the outlet box.
w.2 - To avoid possible electrical shock, before installing or servicing your fan, disconnect the power by turning off the circuit breakers to the outlet box and associated wall switch location. If you cannot lock the circuit breakers in the off position, securely fasten a prominent warning device, such as a tag, to the service panel.
w.3 – To reduce the risk of electric shock, this fan must be installed with an isolating wall control/switch.
w.4 - To reduce the risk of personal injury, do not bend the blade brackets when installing the blade brackets, balancing the blades, or cleaning the fan. Do not insert foreign objects in between rotating fan blades.
c.1 - All wiring must be in accordance with national and local electrical codes ANSI/NFPA 70. If you are unfamiliar with wiring, use a qualified electrician. c.2 - Use only Hunter replacement parts.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help.
Caution: modifications not approved by the party responsible for compliance could void user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Hunter Pro Tip: Do not discard the hardware bags or mix parts from different bags. Make note of the symbol printed on each hardware bag. The symbols can be used to identify the appropriate hardware for each step.
bag Washer x2 For installing the hanger bracket and wiring the fan Wood Screw x2 Wire Nut x4 Ceiling Bracket Canopy Downrod Adapter Cover bag Canopy Screw x2 For installing the canopy bag Blade Washer x12 bag Blade Screw x12 For installing the blades bag
For your convenience, you may receive extra fasteners.
Remote M3664-01 r121917 Blade x4 Light Kit Assembly Lower Switch Housing Glass LED Assembly Light Kit Screw x5 bag x3 Short Light Kit Screw For installing the light kit
Don’t take it back to the store. Let us make it right. Visit us at HunterFan.com or call us at 1.888.830.1326.
Hang your fan by a standard downrod. Some fans come with a shorter downrod for a Low Profile installation.
1. You will need a longer downrod. (sold separately at HunterFan.com) 2. If your ceiling angle is greater than 34°, you will also need an Angled Mounting Kit. (Sold separately at HunterFan.com)
3 Hunter Pro Tip:
Hunter Pro Tip: The machine screws are the ones that came with your outlet box.
Use machine screws
and washers when securing to existing ceiling fan-rated outlet box. Make sure it is securely installed and is acceptable for fan support of 31.8 kg (70 lbs) or less.
A NGL ED
For angled ceilings, point opening toward peak.
Use wood screws and washers (included) when securing to support structure with approved electrical outlet box. Drill 9/64” pilot holes in support structure to aid in securing ceiling bracket with hardware found in the hardware bag.
bag Washer x2 x2 Wood Screw
1 2 3 Hunter Pro Tip: The ground wire attached to the downrod is approximately 8 inches.
Slide the adapter cover onto the downrod until it rests against the hanger ball.
Hunter Pro Tip: The adapter cover is not used for low-profile mounting.
Ceiling Bracket Downrod Hanging Fan Wiring Remove the pre-installed setscrew so that the downrod can be inserted.
Canopy Blades Pass all wires to one side of horizontal bar in downrod assembly. Hand tighten the downrod (at least 4–5 full turns) until it stops. Trim the wires coming from the fan so that 8-inches remain coming from the top of the downrod.
Light Remote App 4
5 Tighten the setscrew with pliers.
DO NOT HAND TIGHTEN.
FAN FALL HAZARD
To prevent SERIOUS INJURY or DEATH: • ALWAYS tighten setscrew with pliers.
• DO NOT hand tighten setscrew.
• CHECK the setscrew is tight using pliers each time you change fan direction.
Lower the adapter cover until it rests flush against the motor housing.
an c op y o ve r d ow nrod
To prevent damage to fan, ALWAYS lift holding either the fan housing or the downrod.
Place the downrod ball into the slot in the ceiling bracket. 5 Ceiling Bracket Downrod Hanging Fan Wiring Canopy Blades Light Remote App
Hunter Pro Tip:
Here is how to connect the wires:
Push the bare metal ends of the wires together and slide a wire nut over them. Then, twist the wire nut clockwise until tight.
Give it a gentle pull to make sure none of the wires are loose.
Connect the white (grounded) wire from the ceiling to the white wire from the fan.
White Grounded Connect the black (ungrounded) wire from the ceiling to the black wire from the fan.
Ungrounded Black Cap the blue wire from the fan.
Blue Grounding e r G en /Ye l low Str ipe Green/Yellow Stripe bag Wire Nut x4 Connect the three grounding wires (green, green/yellow stripe, or bare copper) coming from the ceiling, downrod, and hanging bracket.
Hunter Pro Tip:
Have extra wiring?
Turn the wires upward and push them carefully back through the hanger bracket into the outlet box. Make sure that the wires are still attached to the wire nuts.
Connect the white (grounded) wire from the ceiling to the white wire from the fan.
Connect the black (ungrounded) wire from the ceiling to the black wire from the fan.
White Grounded Ungrounded Black Blue Ung rounded (light) Connect the second ungrounded (light) wire from the ceiling to the blue wire from the fan.
Grounding e r G en /Ye l low Str ipe Green/Yellow Stripe bag Wire Nut x4 Connect the three grounding wires (green, green/yellow stripe, or bare copper) coming from the ceiling, downrod, and hanging bracket.
Visit our wiring video at: http://bit.ly/WireYourFan
Ceiling Bracket Downrod Hanging Fan Wiring Canopy Blades Light Remote App 6
Insert the two canopy screws found in the hardware bag.
bag x2 Canopy Screw e c th an op y in pla ce as s hown.
Insert the blade into the blade slot.
Lift the canopy into place so that the screw holes are aligned.
7 Ceiling Bracket Downrod Hanging Fan Wiring Put the blade washers found in the hardware bag onto the blade screws found in the hardware bag. Then install the blade screws to secure each blade to the fan.
bag Blade Screw x12 bag Blade Washer x12 Canopy Blades Light Remote App
bag 2 of 5 Light Kit Screw
bag 3 of 5 Light Kit Screw bag 2 of 2 Short Light Kit Screw
Partially install two light kit assembly screws, found in the hardware bag, halfway into the motor housing as shown. It does not matter which two screw holes you choose.
Align the keyhole slots in the top of the light kit assembly with the partially installed assembly screws. Wrap the keyhole slots around the screws and twist counterclockwise. Install the third screw. Tighten all three screws securely.
Feed the light wires through the hole in the lower switch housing. Align the lower switch housing screw holes with the bottom of the light kit assembly. Using the three Short Light Kit Screws, found in the hardware bag, mount the lower switch housing to the light kit.
bag 5 of 5 Light Kit Screw Raise the LED assembly to the trim ring. Align the screw holes in the LED assembly with the screw holes in the trim ring.
Screw two light kit assembly screws, found in the hardware bag, through the LED assembly and into the trim ring.
Connect the single-pin connectors from the LED assembly to the connectors from the fan. Connect the white wires together. Connect the blue and black wires together. Tuck the excess wiring above the LED assembly or feed back into the lower switch housing.
Make sure all screws are tight to secure the light fixture.
Notch Tab Lift the globe and align the notches in the globe with the tabs in the light kit.
Ceiling Bracket Downrod Hanging Fan Wiring Canopy
Attach the globe by lifting and turning clockwise one third of a full turn of the glass until it stops.
NOTE: Check to ensure proper engagement.
To prevent SERIOUS INJURY or DEATH , make sure that glass is properly secured.
8 Remote App
Remove the cradle from the cradle bracket.
Separate the lining from the back of the adhesive strip on the cradle bracket.
Press the cradle bracket against the wall and hold firmly for 30 seconds.
Choose your cradle installation location.
If you are installing into drywall, drill two 9/64 width holes using the cradle bracket as a guide. Gently hammer the included drywall anchors into the pre-drilled holes.
Slide the cradle onto the mounted bracket.
Use of the HomeKit logo means that an electronic accessory has been designed to connect specifically to iPod, iPhone, or iPad, respectively, and has been certified by the developer to meet Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards. Please note that the use of this accessory with iPod, iPhone, or iPad may affect wireless performance.
Compatible with iOS 7.1 or higher / Android 4.3 or higher Android and Google Play are trademarks of Google Inc.
Apple logo is a trademark of Apple, Inc.
App store is a service mark of Apple, Inc.
9 Ceiling Bracket Downrod Hanging Fan Fan not showing up in the list? Pull down to refresh!
Wiring Canopy Blades
The HomeKit setup code is located on the front cover of the English side of this manual.
Hunter Pro Tip:
Need to install the app later?
When ready, turn the wall switch off and then on. Wait three minutes before downloading the app. Light Remote App
• Make sure power switch is on.
• Pull the pull chain to make sure it is on.
• Push the motor reversing switch firmly left or right to ensure that it is engaged.
• Check the circuit breaker to ensure the power is turned on.
• Make sure the blades spin freely.
• Turn off power from the circuit breaker, then loosen the canopy and check all the connections according to the wiring diagram.
• Check the plug connection in the switch housing.
• Make sure the blades are properly installed on the blade iron posts.
• Turn the power off, support the fan carefully, and check that the hanger ball is properly seated.
• Use the provided balancing kit and instructions to balance the fan.
• Make sure the battery is installed correctly.
• Install a fresh battery.
• Change battery.
• Make sure the blades are properly installed.
• Check to see if any of the blades are cracked. If so, replace all of the blades.
• If you have multiple remotes or multiple remote-controlled fans installed on the same circuit breaker and you are experiencing interference or faulty operation of your remote controls, please go to www.HunterFan.com/FAQs and click “How do I properly install multiple remote-controlled fans?” for information on how to correct this issue.
• Reset the Wi-Fi module by removing the battery door. Press and hold the reset button for 5 seconds. The fan and light LEDs will flash once the module has been reset. Hunter Pro Tip:
Cleaning the Fan
Use soft brushes or cloths to prevent scratching. Cleaning products may damage the finishes.
Hunter Fan Company grants this limited warranty to the original purchaser of this Hunter ceiling fan. This document can be found at www.HunterFan.com. Thank you for choosing Hunter!
Proof of purchase is required
when requesting warranty service. The original purchaser must present a sales receipt or other document that establishes proof of purchase. Hunter, at its sole discretion, may accept a gift receipt. To obtain service, contact Hunter Fan Company online or by phone.
www.HunterFan.com/Support/Contact-Us/ 1-888-830-1326 Please do not ship your fan or any fan parts to Hunter. Delivery will be refused.
Motor — Limited Lifetime Warranty
If any part of your ceiling fan motor fails during your ownership of the fan due to a defect in material or workmanship, as determined solely by Hunter, Hunter will provide you with a replacement fan free of charge.* The foregoing limited warranty applies only to the motor itself and does not apply to electronic controls – such as remote control transmitters, remote control receivers, or capacitors – used in conjunction with the motor. Such electronic control items are included in the one-year limited warranty below.
Other — One-Year Limited Warranty
Except as otherwise indicated throughout this warranty, if any part of your Hunter ceiling fan fails at any time within one year of the date of purchase due to a defect in material or workmanship, as determined solely by Hunter, Hunter will provide a replacement part free of charge.*
Light Kits — Warranty May Vary
Light kits are included in the one-year limited warranty. However, you may qualify for additional warranty coverage if your fan includes one of the following: •
LED Light Kits — Three-Year Limited Warranty
If your LED light kit module (not including glass components) or LED bulb fails at any time within three years of the date of purchase due to a defect in material or workmanship, as determined solely by Hunter, Hunter will provide a replacement part free of charge.* •
ENERGY STAR® Rated Light Kits — Three-Year Limited Warranty
If your ENERGY STAR rated light kit (not including glass components) fails at any time within three years of the date of purchase due to a defect in material or workmanship, as determined solely by Hunter, Hunter will provide a replacement light kit free of charge.*
* If no replacement product/part can be provided for your fan, we will provide a comparable or superior replacement product/part at the sole discretion of Hunter.
Labor Excluded. This warranty does not cover any costs or fees associated with the labor (including electrician’s fees) required to install, remove, or replace a fan or any fan parts. There is no warranty for light bulbs (except where otherwise noted); remote control batteries; fans purchased or installed outside the United States; fans owned by someone other than the original purchaser; fans for which proof of purchase has not been established; fans purchased from an unauthorized dealer; ordinary wear and tear; minor cosmetic blemishes; refurbished fans; and fans that are damaged due to any of the following: improper installation, misuse, abuse, improper care, failure to follow Hunter instructions, accidental damage caused by the fan owner or related parties, modifications to the fan, improper or incorrectly performed maintenance or repair, improper voltage supply or power surge, use of improper parts or accessories, failure to provide maintenance to the fan, or acts of God (e.g. flood). ORIGINAL PURCHASER’S SOLE AND EXCLUSIVE REMEDY FOR A CLAIM OF ANY KIND WITH RESPECT TO THIS PRODUCT SHALL BE THE REMEDIES SET FORTH HEREIN. HUNTER FAN COMPANY IS NOT RESPONSIBLE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, DUE TO PRODUCT FAILURE, WHETHER ARISING OUT OF BREACH OF WARRANTY, BREACH OF CONTRACT, OR OTHERWISE. Some States do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE APPLICABLE TO THIS PRODUCT ARE LIMITED IN DURATION TO THE PERIOD OF COVERAGE OF THE APPLICABLE LIMITED WARRANTIES SET FORTH ABOVE. Some States do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.
This warranty gives you specific legal rights. You may also have other rights which vary from state to state.
3 4 5 10 9 8
FAN FALL HAZARD
To prevent SERIOUS INJURY or DEATH: • ALWAYS follow the downrod assembly instructions exactly.
• VERIFY the downrod is assembled correctly by firmly pulling on the hanger ball.