Hunter Cabo Frio Outdoor 52 inch Owners Manual

Hunter Cabo Frio Outdoor 52 inch Owners Manual
www.HunterFanInternational.com
Table of Contents
What to Expect with
Your Installation
30 inches
Downrod
Ladder
3
Wiring
11
Troubleshooting
?
?
?
20
PA G E
16
PA G E
PA G E
PA G E
1
MB529-01 • 11/15/16 • © 2016 Hunter Fan Company
10
Operation,
Maintenance & Cleaning
14
5
Blades
PA G E
9
Wall Control
Switch Housing
12
Canopy
PA G E
6
4
PA G E
2
PA G E
7 feet
PA G E
Save your receipt for proof of purchase.
Ceiling Bracket
PA G E
To register your fan, please visit:
www.HunterFan.com/register
Mounting Options
PA G E
We are proud of our work and appreciate
the opportunity to supply you with the best
ceiling fan available anywhere in the world.
Tools Needed
PA G E
Congratulations on purchasing your new
Hunter® ceiling fan! It will provide comfort
and performance in your home or office for
many years. This installation and operation
manual contains complete instructions for
installing and operating your fan.
www.HunterFanInternational.com
What to Expect with Your Installation
Read and Save These Instructions
This product conforms to UL Standard 507.
If you are unfamiliar
with wiring, use a
qualified electrician.
WARNINGS
,8 Meters
(30 inches)
from blade tip
to nearest wall
or obstruction
Must be able to
secure the fan to
building structure or
fan-rated outlet box
Know your wiring
You may need a
friend to help you.
Check box to see
fan weight
Assess ceiling angle
from bottom
edge of blade
to the floor
Assess location
1
Ceiling angles greater
than 34° will require an
Angled Mounting Kit.
See page 4 for details.
2,1 Meters
(7 feet)
Standard Downrod
for ceilings 2,4-3 m (8-10 feet) high
2
Shorter Downrod
3
Longer Downrod
for fans installed close to ceiling
for ceilings 3 m (10 feet) or higher
Select a downrod length
w.1 - To reduce the risk of fire, electrical shock, or personal
injury, mount fan directly from building structure and/or
an outlet box marked acceptable for fan support of 70 lbs
(31.8 kg) and use the mounting screws provided with the
outlet box.
w.2 - To avoid possible electrical shock, before installing
or servicing your fan, disconnect the power by turning
off the circuit breakers to the outlet box and associated
wall switch location. If you cannot lock the circuit breakers
in the off position, securely fasten a prominent warning
device, such as a tag, to the service panel.
w.3 - To reduce the risk of fire, electrical shock, or motor
damage, use only Hunter Solid State Speed Controls.
w.4 - To reduce the risk of personal injury, do not bend the
blade brackets when installing the blade brackets, balancing
the blades, or cleaning the fan. Do not insert foreign objects in
between rotating fan blades.
w.5 - This product is not intended to be used by people
(including children) whose physical, sensory, or mental
capacities are different or diminished, or lack of experience
or knowledge, unless such persons receive training or work
under supervision of a person responsible for their safety.
w.6 - Children should be supervised to ensure they do not use
the devices as a toy.
CAUTIONS
c.1 - All wiring must be in accordance with national and local
electrical codes ANSI/NFPA 70. If you are unfamiliar with
wiring, use a qualified electrician.
c.2 - Use only Hunter replacement parts.
2
MB529-01 • 11/15/16 • © 2016 Hunter Fan Company
www.HunterFanInternational.com
Tools Needed
Ladder
Screwdrivers
Pliers
Wire Strippers
9/64” Drill Bit
(optional)
Power Drill
(optional)
If mounting to a support structure, you will also need these tools.
3
MB529-01 • 11/15/16 • © 2016 Hunter Fan Company
Do not discard the hardware bags or mix
parts from different bags. Make note of
the symbol printed on each hardware
bag. The symbols can be used to identify
the appropriate hardware for each step.
34O
CEILING
www.HunterFanInternational.com
Mounting Options
OPTION 1
If you have a flat ceiling:
1. You will need a longer downrod (sold separately).
2. If your ceiling angle is greater than 34°, you will
also need an Angled Mounting Kit (sold separately).
Angled
Mounting
Support
Structure
Support
Structure
OPTION 2
If you have an angled ceiling:
Standard
Mounting
Style
Ceiling
Outlet Box
(required)
Use the three steps below to determine if your ceiling angle is greater than 34°
2
1
Ceiling
Outlet Box
(required)
Angled
Mounting
Style
3
34°
PLACE
FOLD
against wall
on dotted line
Guide Touches
BOTH Ceiling & Wall
You need ONLY
a Longer
Downrod
*most common
SLIDE
toward ceiling
Guide Touches Wall
but NOT Ceiling
2
ON
SITUAT
I
1
ON
SITUAT
I
WALL
Standard
Mounting
Hang your fan by a standard downrod (included).
Use Standard Mounting
to hang the fan from a flat ceiling.
You need BOTH
a Longer
Downrod &
an Angled
Mounting Kit
4
MB529-01 • 11/15/16 • © 2016 Hunter Fan Company
Use Angled Mounting
to hang the fan from a
vaulted or angled ceiling.
www.HunterFanInternational.com
Ceiling Bracket
r
we
o
nP
r
Tu
OFF
For angled ceilings, point
opening toward peak.
Use wood screws
Use machine screws
(included) when securing
(provided with outlet
to support structure with
box) when securing to
approved electrical outlet existing ceiling fan-rated
box. Drill 9/64” pilot holes
outlet box. Make sure
in support structure to aid
it is securely installed
in securing ceiling bracket and is acceptable for fan
with hardware found in support of 31.8 kg (70 lbs)
the
hardware bag.
or less.
Make sure all four bumpers are
still attached.
If you are unable to do this,
call Technical Support at
1-888-830-1326.
Refer to warning w.1 on pg. 2
5
MB529-01 • 11/15/16 • © 2016 Hunter Fan Company
To avoid possible electrical shock, before
installing your fan, disconnect the power by
turning off the circuit breakers to the outlet
box associated with the wall switch location.
www.HunterFanInternational.com
skip to next page
Standard
Downrod
for ceilings 8-10’ high
Steps 1-5 to remove standard downrod pipe
1
2
3
4
10
9
8
Steps 6-10 to reassemble with new pipe
6
MB529-01 • 11/15/16 • © 2016 Hunter Fan Company
5
Slide
Slide
Longer
Downrod
for angled
ceilings or
ceilings 10’ or
higher
Sold Separately
Option 2
If you need a different downrod length follow these steps:
Included
(pre-assembled)
Option 1
Downrod
7
6
www.HunterFanInternational.com
KEEP!
(not to scale)
20 cm
(8”)
&
1 cm
(3/8”)
STRIP
CUT
Downrod (continued)
!
KEEP
Remove the pre-installed
setscrew so that the downrod
can be inserted.
Hand tighten the downrod (at
least 4-5 full turns) until it stops.
The wires can be cut, but
leave at least 8” extending
from the top of the downrod.
20 cm
(8”)
Tighten the setscrew
with pliers. DO NOT
HAND TIGHTEN.
1 cm
(3/8”)
If the setscrew is not tightened
securely, the fan may fall.
7
MB529-01 • 11/15/16 • © 2016 Hunter Fan Company
www.HunterFanInternational.com
Downrod (continued)
Put the wires and downrod through the
canopy. Let the canopy sit loosely on top
of the fan.
DO NOT PICK THE FAN UP BY THE
CANOPY OR WIRES. Place the downrod
ball into the slot in the ceiling bracket.
8
MB529-01 • 11/15/16 • © 2016 Hunter Fan Company
Wiring
OM
FR
CEILIN
Note: To connect the wires, hold the bare metal
leads together and place a wire connector over
them, then twist clockwise until tight.
G
M FA N
Using the orange wire
connectors from the
hardware bag, connect the
black wire (ungrounded) from
the ceiling to the black and
the black with white stripe
wires from the fan. Connect
the white wire (grounded)
from the ceiling to the white
wire from the fan.
T
FRO
Black
Black with
white stripe
CEIL
KE
M
G
(Ungrounded)
Green/Yellow
Stripe
FR
O
CEILIN
White
Using an orange wire
connector from the
hardware bag, connect the
3 grounding wires (green,
green/yellow stripe, or
bare copper) coming from
the ceiling, downrod, and
hanging bracket.
Green/Yellow
Stripe
OM
FR
(Grounded)
(Grounding)
OM FAN
FR
www.HunterFanInternational.com
ING BR
AC
Turn the splices upward and push them carefully back through the hanger bracket
into the outlet box. Spread the wires apart, with the grounded wires on one side of
the outlet box and the ungrounded wires on the other side of the outlet box.
Refer to CAUTION c.1 on pg. 2
9
MB529-01 • 11/15/16 • © 2016 Hunter Fan Company
www.HunterFanInternational.com
Canopy
Screw
Holes
Position the canopy so that, when
lifted into place, the canopy fits into
the hanging bracket as shown.
Lift the canopy into place so that
the screw holes are aligned.
Install the two canopy screws,
found in the
hardware bag.
Note: Fan style may vary.
10
MB529-01 • 11/15/16 • © 2016 Hunter Fan Company
Blades
Insert each blade into a slot. Align the holes on
the blade with the holes on the blade ring.
www.HunterFanInternational.com
Attach the blade to the blade ring
using the blade assembly screws,
found in the
hardware bag.
11
MB529-01 • 11/15/16 • © 2016 Hunter Fan Company
Switch Housing
Partially install two machine screws, found
in the
hardware bag, halfway into the
motor housing. It does not matter which
two screw holes you choose.
www.HunterFanInternational.com
Feed the wires through the center hole
of the upper switch housing, then wrap
the keyhole slots around the screws
and twist counterclockwise.
Use only the light fixture supplied with this fan model.
12
MB529-01 • 11/15/16 • © 2016 Hunter Fan Company
Insert the third screw, found in
the
hardware bag, into place and
then tighten all three screws.
Make sure the heat shield assembly is securely attached to
the housing mounting plate. Failure to properly attach and
tighten all three assembly screws could result in the heat
shield assembly and light fixture falling.
Switch Housing (continued)
www.HunterFanInternational.com
Raise the bottom cap to the switch
housing. Align the screw holes in the
switch housing and the screw holes in
the bottom cap.
Attach the bottom cap with the three
provided screws from the
hardware bag.
13
MB529-01 • 11/15/16 • © 2016 Hunter Fan Company
www.HunterFanInternational.com
Wall Control
2
3
1
1.
1.
1.
2
2
3
3
1
1
2.
Shut off power to the room you will
be working in at the breaker box.
After removing the switch plate cover,
remove all wiring from the switch.
2.
Using the wire connectors, connect each
black wire from the wall control to a
black wire from the switch box. Connect
ground wire from the switch box to the
green/yellow wire from the wall control.
Note: If two white wires are present in
the switch box, connect them to each
other if they are not already connected.
Do not restore power until all work is complete.
14
MB529-01 • 11/15/16 • © 2016 Hunter Fan Company
2.
Insert the wall control into the
outlet box and secure the two metal
tabs to the tabs on the switch box
using the two flat head screws that
came with the switch box.
www.HunterFanInternational.com
Wall Control (continued)
1.
2
3
1
2
3
1
CONGRA
T
YOU’REUALTIONS!
DONE!
2.
Remove the knob from the wall
control and mount the faceplate
(not included) to the wall control
using the two #6-32 screws you
removed earlier from the faceplate.
Reattach the knob onto the wall
control and turn it to the left for the
OFF position.
15
MB529-01 • 11/15/16 • © 2016 Hunter Fan Company
www.HunterFanInternational.com
Operation, Maintenance & Cleaning
Reverse
Switch
r
Tu
r
we
o
nP
2
3
1
ON
The knob on the wall control unit
controls power to the fan. The fan has
four speed settings in sequence:
high, medium, low and off.
To change the direction of air flow,
move the reverse switch to the
opposite position.
16
MB529-01 • 11/15/16 • © 2016 Hunter Fan Company
For cleaning the fan, use soft brushes or
cloths to prevent scratching. Cleaning
products may damage the finishes.
www.HunterFanInternational.com
Troubleshooting
Fan doesn’t work
Excessive wobbling
• Make sure power switch is on.
• Tighten all of the blade and
blade ring screws until they
are snug.
• Push the motor reversing switch
firmly left or right to ensure that
it is engaged.
• Check the circuit breaker to
ensure the power is turned on.
• Turn the power off, support
the fan carefully, and check
that the hanger ball is
properly seated.
• Make sure the blades spin freely.
• Turn off power from the circuit
breaker, then loosen the canopy
and check all the connections
according to the wiring diagram
on page 9.
• Turn off power from the circuit
breaker, then ensure the wall
control is properly installed
according to the instructions on
pages 14-15.
Noisy Operation
• Tighten the blade and blade
ring screws until they are snug.
• Check to see if any of the
blades are cracked. If so, replace
all of the blades.
17
MB529-01 • 11/15/16 • © 2016 Hunter Fan Company
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement