Hunter Gilmour Indoor/Outdoor Owners Manual

Hunter Gilmour Indoor/Outdoor Owners Manual

Model: 51333 Flat Matte Black 51334 Matte Fresh White Fan weight ±2 lbs: 16.8 lbs (7.6 kg)

Gilmour

Installation Manual

©2019 Hunter Fan Co.

PG3841 r120519

Congratulations on purchasing your new Hunter

®

ceiling fan!

The ceiling fan you purchased will provide comfort and performance in your home or office for many years. This instruction manual contains complete instructions for installing and operating your fan. We are proud of our work and appreciate the opportunity to supply you with the best ceiling fan available anywhere in the world.

We are here to help!

This Instruction Manual is designed to make installation as simple as possible. While working through this Instruction Manual, keep your smartphone or tablet nearby. We have added video links to help you through the more technical sections. If you are unfamiliar or uncomfortable with wiring, contact a qualified electrician. We also provide telephone support at 1.888.830.1326 or visit us at HunterFan.com.

READ and SAVE These Instructions WARNING

1886

Warning

w.1 - To reduce the risk of fire, electrical shock, or personal injury, mount fan directly from building structure and/or an outlet box marked acceptable for fan support of 70 lbs (31.8 kg) and use the mounting screws provided with the outlet box.

w.2 - To avoid possible electrical shock, before installing or servicing your fan, disconnect the power by turning off the circuit breakers to the outlet box and associated wall switch location. If you cannot lock the circuit breakers in the off position, securely fasten a prominent warning device, such as a tag, to the service panel.

w.3 – To reduce the risk of electric shock, this fan must be installed with an isolating wall control/switch.

w.4 - To reduce the risk of personal injury, do not bend the blade brackets when installing the blade brackets, balancing the blades, or cleaning the fan. Do not insert foreign objects in between rotating fan blades.

Caution

c.1 - All wiring must be in accordance with national and local electrical codes ANSI/NFPA 70. If you are unfamiliar with wiring, use a qualified electrician. c.2 - Use only Hunter replacement parts.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help.

Caution: modifications not approved by the party responsible for compliance could void user’s authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This product conforms to UL Standard 507.

Ladder Here are the tools you’ll need to complete your installation:

OPTIONAL

If mounting to a support structure, you will also need these tools.

Screwdriver Drill 9/64” Drill Bit

© 2019 Hunter Fan Company 7130 Goodlett Farms Pkwy, Suite 400 Memphis TN 38016

1

Pliers Wire Strippers

1886

Here is what comes in your box: We recommend that you pull everything out of the box and lay it out. We have grouped the drawn components below with the hardware you’ll need for those parts. The screws below are drawn to scale to make it easier to identify what piece of hardware is needed to install each component.

Hunter Pro Tip:

Do not discard the hardware bags or mix parts from different bags. Make note of the symbol printed on each hardware bag. The symbols can be used to identify the appropriate hardware for each step.

1886

Wood Screw

x2

Ceiling Bracket

bag

Washer

x2 For installing the hanger bracket and wiring the fan

Wire Nut

x4

Canopy

bag

Canopy Screw

x3

Top Housing Screw

x3

Blade

x3 bag x9

Blade Screw

For installing the canopy

Motor Upper Switch Housing

bag

Blade Washers

x9

Light Kit

bag x6

Light Kit Screw

For installing the blades

Bulb

x2 bag

Spare Parts For your convenience, you may receive extra fasteners.

Globe Remote Control Remote Cradle Remote Receiver

Remote Components M3777-01 r120519 Note: Fan style may vary.

For installing the light kit

Find a part that is missing or damaged?

Don’t take it back to the store. Let us make it right. Visit us at HunterFan.com or call us at 1.888.830.1326.

2

1886

Choosing the Right Installation Location You probably bought this fan with a location in mind. Let’s check below to make sure it is a good fit.

Check the room dimensions: Check the outlet box: 30 inches

from blade tip to nearest wall or obstruction

7 feet

from bottom edge of blade to the floor

You must be able to secure the fan to building structure or fan-rated outlet box.

Installing the Ceiling Bracket You have

two options

for installation. Pick which one works best for your location. Remove any existing bracket prior to installation.

Only use the provided Hunter ceiling bracket that came in your fan’s box.

Do this first!

ow er

WARNING

To avoid possible electrical shock, before installing your fan, disconnect the power by turning off the circuit breakers to the outlet box associated with the wall switch location.

Option 1:

Machine Screws

Use machine screws

(provided with outlet box)

and washers when securing to existing ceiling fan-rated outlet box. Make sure it is securely installed and is acceptable for fan support of 31.8 kg (70 lbs) or less.

Option 2:

Wood Screws

Use wood screws and washers (included) when securing to support structure with approved electrical outlet box. Drill 9/64” pilot holes in support structure to aid in securing ceiling bracket with hardware found in the hardware bag.

bag

Washer

x2 3 Hunter Pro Tip:

The machine screws are the ones that came with your outlet box.

Ceiling Bracket Hanging Fan Wiring Canopy Blades Light Bulbs x2

Wood Screw

Remote

1886

1886

Check the outlet box:

Top Housing

Installing the Top Housing

bag x3

Top Housing Screw

Adapter Thread the wires through the top housing. Place the top housing onto the motor housing so that the holes in the top housing lineup with the holes in the motor housing and the adapter.

Install the top housing screws. These screws can be found in the hardware bag.

Note: Fan style may vary.

Hanging the Fan

Wood Screw

NOTICE

To prevent damage to fan, ALWAYS lift holding the fan housing.

Raise the fan and align the slots in the canopy with the hooks on the ceiling plate.

Note:

To hang the fan, you must tilt the canopy to an almost vertical position so that the canopy slots sit on the ceiling plate hooks.

Place the slots over the ceiling plate hooks to hang the fan.

Ceiling Bracket Hanging Fan Wiring Canopy Blades Light Bulbs Remote 4

1886

1886

Wiring the Fan We know wiring is hard. Let’s make it easier.

Follow these steps to get your fan wired quickly and safely. Follow the route below that best matches your wall switch setup. If you are unfamiliar with wiring or uncomfortable doing it yourself, please contact a qualified electrician.

You are going to need these: 4 Wire Nuts (these are in the bag)

Hunter Pro Tip:

Here is how to connect the wires:

Push the bare metal ends of the wires together and slide a wire nut over them. Then, twist the wire nut clockwise until tight.

Give it a gentle pull to make sure none of the wires are loose.

1 Ung rounded Grounded White White Connect the white wire (grounded) from the ceiling to both the white wire from the receiver and the white wire from the fan. Connect the 2 grounding wires (green, green/ yellow stripe, or bare copper) coming from the ceiling and ceiling plate. Black Connect the black wire (ungrounded) from the ceiling to the black wire from the receiver. 2 Note: Fan style may vary.

WARNING

The ceiling fan must be grounded. If the ground wire for the installation site is not present, immediately

STOP

installation and consult a qualified electrician.

WARNING

All wiring must be in accordance with national and local electrical codes ANSI/NFPA 70. If you are unfamiliar with wiring or in doubt, consult a qualified electrician.

Connect the blue wire from the receiver to the blue wire (or possibly black with white stripe wire) from the fan.

Blue Blue 5 Ceiling Bracket Note: Fan style may vary.

Hanging Fan Wiring Canopy Blades Yello w Black Connect the yellow wire from the receiver to the black wire from the fan. Light Bulbs Remote

1886

1886

Installing the Canopy

Place the receiver inside the canopy. Ensure the wires remain connected.

Swing the fan up to align the canopy screw holes with the mounting holes on the ceiling plate.

Note:

The slots in the canopy must remain engaged while swinging the canopy for alignment.

Ceiling Plate Hooks Hold the canopy up with the screw holes aligned. Partially install two canopy screws, found in the hardware bag, into the holes opposite the ceiling plate hooks.

bag

Canopy Screws

2 of 3

1886

Note: Fan style may vary.

Partially install a canopy screw, found in the hardware bag, between the ceiling plate hooks. When all the holes are properly aligned, securely tighten all three canopy screws.

bag

Canopy Screws

1 of 3

Installing the Blades

WARNING FAN FALL HAZARD

Make sure screws are tight.

Ceiling Bracket Hanging Fan bag x9

Blade Screw

Wiring Put the blade washers found in the hardware bag onto the blade screws found in the hardware bag. Then install the blade screws to secure each blade to the fan.

Repeat x3 IMPORTANT

NOTE: Follow the instructions on the blade. Installing it incorrectly could result in your fan not functioning.

Canopy Blades Light bag

Blade Washer

x9 Bulbs Remote 6

1886

bag 2 of 6

Light Kit Screw

Assembling the Light Kit

bag 1 of 6

Light Kit Screw

Partially install two light kit assembly screws, found in the hardware bag, halfway into the motor housing as shown. It does not matter which two screw holes you choose.

bag 2 of 6

Light Kit Screw

Feed the wire plug through the center hole of the upper switch housing, then wrap keyhole slots around the screws and twist counterclockwise.

Insert the third screw, found in the hardware bag, into place and then tighten all three screws.

bag 1 of 6

Light Kit Screw

Partially install two of the light kit screws found in the bag. It does not matter which two screw holes you choose. Connect the plugs from the upper and lower switch housings. Make sure to line up the colored markings on the connectors.

Note: Fan style may vary.

Align the keyhole slots in the light kit housing with the two screws. Make sure all the wires from the fan and the light kit are snug inside the center of the light kit, not pinched in between the upper switch housing and the light kit or hanging out of the sides.

Turn the light kit counterclockwise until the light kit screws are firmly situated in the narrow end of the keyhole slots. Install the third screw and tighten all three screws securely.

WARNING FAN FALL HAZARD

Make sure all screws are tight to secure the light fixture.

Installing the Globe

7 Install the included bulbs into the sockets. When necessary, replace with bulbs of same wattage.

Ceiling Bracket Tab Hanging Fan Lift the globe and align the notches in the globe with the tabs in the light kit.

Wiring Notch Canopy Attach the globe by lifting and turning clockwise one third of a full turn of the globe until it stops.

NOTE: Check to ensure proper engagement.

WARNING GLOBE FALL HAZARD

To prevent SERIOUS INJURY , make sure that globe is properly secured.

Blades Light Bulbs Remote

Installing the Remote Control Cradle

1886

1886

Preparing the Remote For your convenience, a remote function card is packed in with your remote.

ow

ON

er

To access the battery compartment, remove the the battery door to the transmitter assembly.

IMPORTANT

Battery Door • Always purchase the correct size and grade of battery most suitable for the intended use.

• Replace all batteries of a set at the same time.

• Clean the battery contacts and also those of the device prior to battery installation.

• Ensure the batteries are installed correctly with regard to polarity (+ and -).

• Remove batteries from equipment which is not to be used for an extended period of time.

• Remove used batteries promptly.

Install two AAA batteries, found in the remote control hardware bag, into the transmitter. Clean the battery contacts prior to installing the batteries. Please contact your local battery recycling center for proper battery disposal information.

The Fan On/Off button turns the fan on or off. Adjust the fan speed using the “Fan Speed Up” or “Fan Speed Down” directional buttons.

NOTICE : DIMMING MODE

To enable dimming, your remote must be set to Dimming Mode. To toggle Dimming Mode on or off, long press the “Fan Speed Up” button and “Fan Speed Down” button.

Installing the Remote Control Cradle You have two options for installing the remote cradle.

Choose which path works best for you.

Fan On/Off Fan Speed Up Fan Speed Down The remote transmitter is already paired to the receiver and ready to use.

Dimming mode is off by default.

Note: If you need to pair your remote, turn fan power off and back on at the wall switch. Within 3 minutes, press and release the “PAIR” button on the back of the remote.

Do not hold down the button.

To prevent faulty operation, please ensure all other ceiling fans within range are turned off at the wall switch while pairing.

Quick Press: Light On/Off Long Press: Light Dimming Quickly press the Light button to turn the lights off and on.

Hold the Light button to raise and dim the light level.

1886

Option 1: Using Adhesive Strip Option 2: Using Screws

Remove the cradle from the cradle bracket.

Separate the lining from the back of the adhesive strip on the cradle bracket.

Press the cradle bracket against the wall and hold firmly for 30 seconds.

Ceiling Bracket Hanging Fan Wiring Canopy

Choose your cradle installation location.

If you are installing into drywall, drill two 9/64 width holes using the cradle bracket as a guide. Gently hammer the included drywall anchors into the pre-drilled holes.

Blades Light Bulbs

Slide the cradle onto the mounted bracket.

Remote 8

1886

Reversing the Fan

Reverse Switch Updraft (clockwise rotation) creates a more indirect airflow. Updraft airflow is great for moving warm air downward.

Downdraft (counterclockwise rotation) creates a direct breeze and maximum cooling effect.

Ceiling fans work in two directions: downdraft (counterclockwise rotation) and updraft (clockwise rotation). To change the direction of air flow, turn the fan off and let it come to a complete stop. Slide the reversing switch to the opposite position. Restart the fan.

9

Limited Lifetime Warranty

Hunter Fan Company grants this limited warranty to the original purchaser of this Hunter ceiling fan. This document can be found at www.HunterFan.com. Thank you for choosing Hunter!

How Can Warranty Service Be Obtained?

Proof of purchase is required

when requesting warranty service. The original purchaser must present a sales receipt or other document that establishes proof of purchase. Hunter, at its sole discretion, may accept a gift receipt. To obtain service, contact Hunter Fan Company online or by phone.

www.HunterFan.com/Support/Contact-Us/ 1-888-830-1326 Please do not ship your fan or any fan parts to Hunter. Delivery will be refused.

What Does This Warranty Cover?

Motor — Limited Lifetime Warranty

If any part of your ceiling fan motor fails during your ownership of the fan due to a defect in material or workmanship, as determined solely by Hunter, Hunter will provide you with a replacement fan free of charge.* The foregoing limited warranty applies only to the motor itself and does not apply to electronic controls – such as remote control transmitters, remote control receivers, or capacitors – used in conjunction with the motor. Such electronic control items are included in the one-year limited warranty below.

Other — One-Year Limited Warranty

Except as otherwise indicated throughout this warranty, if any part of your Hunter ceiling fan fails at any time within one year of the date of purchase due to a defect in material or workmanship, as determined solely by Hunter, Hunter will provide a replacement part free of charge.*

Light Kits — Warranty May Vary

Light kits are included in the one-year limited warranty. However, you may qualify for additional warranty coverage if your fan includes one of the following: •

LED Light Kits — Three-Year Limited Warranty

If your LED light kit module (not including glass components) or LED bulb fails at any time within three years of the date of purchase due to a defect in material or workmanship, as determined solely by Hunter, Hunter will provide a replacement part free of charge.*

* If no replacement product/part can be provided for your fan, we will provide a comparable or superior replacement product/part at the sole discretion of Hunter.

What Does This Warranty NOT Cover?

Labor Excluded. This warranty does not cover any costs or fees associated with the labor (including electrician’s fees) required to install, remove, or replace a fan or any fan parts. There is no warranty for light bulbs (except where otherwise noted); remote control batteries; fans purchased or installed outside the United States; fans owned by someone other than the original purchaser; fans for which proof of purchase has not been established; fans purchased from an unauthorized dealer; ordinary wear and tear; minor cosmetic blemishes; refurbished fans; and fans that are damaged due to any of the following: improper installation, misuse, abuse, improper care, failure to follow Hunter instructions, accidental damage caused by the fan owner or related parties, modifications to the fan, improper or incorrectly performed maintenance or repair, improper voltage supply or power surge, use of improper parts or accessories, failure to provide maintenance to the fan, or acts of God (e.g. flood). ORIGINAL PURCHASER’S SOLE AND EXCLUSIVE REMEDY FOR A CLAIM OF ANY KIND WITH RESPECT TO THIS PRODUCT SHALL BE THE REMEDIES SET FORTH HEREIN. HUNTER FAN COMPANY IS NOT RESPONSIBLE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, DUE TO PRODUCT FAILURE, WHETHER ARISING OUT OF BREACH OF WARRANTY, BREACH OF CONTRACT, OR OTHERWISE. Some States do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE APPLICABLE TO THIS PRODUCT ARE LIMITED IN DURATION TO THE PERIOD OF COVERAGE OF THE APPLICABLE LIMITED WARRANTIES SET FORTH ABOVE. Some States do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.

How Does State Law Affect Warranty Coverage?

This warranty gives you specific legal rights. You may also have other rights which vary from state to state.

Troubleshooting

1886

1886

Troubleshooting

Fan Doesn’t Work

• Make sure power switch is on.

• Check the circuit breaker to ensure the power is turned on.

• Make sure the blades spin freely.

• Turn off power from the circuit breaker, then loosen the canopy and check all the connections according to the wiring diagram.

Excessive Wobbling

• Make sure the blades are properly installed on the blade iron posts.

• Use the provided balancing kit and instructions to balance the fan.

Noisy Operation

• Make sure the blades are properly installed.

• Check to see if any of the blades are cracked. If so, replace all of the blades.

Remote Control of Fan is Erratic

• Make sure the battery is installed correctly.

• Install a fresh battery.

Multiple Remote Issues

• If you have multiple remotes or multiple remote-controlled fans installed on the same circuit breaker and you are experiencing interference or faulty operation of your remote controls, please go to www.HunterFan.com/FAQs and click “How do I properly install multiple remote-controlled fans?” for information on how to correct this issue.

Hunter Pro Tip:

Cleaning the Fan

Use soft brushes or cloths to prevent scratching. Cleaning products may damage the finishes.

1886

10

Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement