Please initial use MAXSPECTTM LED Aquarium Lamp

Please initial use MAXSPECTTM LED Aquarium Lamp
www.aquaportail.com
Merci de lire ce manuel d'utilisation de la rampe d'éclairage pour aquarium
MAXSPECT™ LED avant tout usage.
Instructions d'emploi de l'éclairage MAXSPECT LED
3 W white light: Flux lumineux = 150-180 lm / Température de couleur = 10000 K
3 W blue-ray: Principale longueur d'onde optique = 450 nm
30 W white light: Flux lumineux = 2000 lm / Température de couleur = 18000 K
L'utilisateur doit d'abord utiliser les instructions sur le réglage horaire en fonction des
paramètres du produit et seulement alors modifier les paramètres usine; si vous ne
modifiez par les réglages usine, le programme par défaut de la rampe LED est activé.
Les groupes de LED à lumière blanche et lumière bleue peuvent être réglées
ensembles ou séparément mais les temps de commutation de chaque groupe ne
peut fixer qu'une seule heure de début et un seul horaire d'arrêt.
1) Time setting:
A. Hold down the "MODE" button for more than 2 seconds to enter
time setting mode;
B. Begins flashing digital clock that is in the clock setting
mode, press "/ WHITE" or "-/BLUE" button set;
C. And then click the "MODE" key to switch to the minute setting
mode, also based on a "/ WHITE" or "-/BLUE" button to set;
D. Is set up according to "TIMER" button to return or more
than 5 seconds does not operate automatically to return;
E. Setting a good time, the electronic clock work (electronic
clock error of the value of a year is less than 2.5 minutes);
F. Set of time after full power to save data.
2) Program settings:
A. Press "TIMER" button for more than 2 seconds to enter
automatically open and close the setting mode;
B. The first is a "WHITE" status indicator light, indicating
that the white group at this time to set the boot or shut down
time. The default state is displayed "on" the words that now
set the boot time;
C. Click the "TIMER" button, the clock started flashing
numbers that are in the clock setting mode, press "/ WHITE"
or "-/BLUE" button to set; and then click the "TIMER" key to
www.aquaportail.com
switch to the minute setting mode , also based on "/ WHITE"
or "-/BLUE" button set;
D. Is set up according to "TIMER" key to display "OFF" the
words that followed set the shutdown time; and then click the
"TIMER" key to begin flashing digital clock that is in the
clock setting mode, press "/ WHITE" or "-/BLUE" button to set;
and then click the "TIMER" key to switch to the minute setting
mode, also based on a "/ WHITE" or "-/BLUE" button to set;
E. Is set up according to "TIMER" button or more than 5 seconds
without any key operation is to save the setting data out of
setting mode;
F. In setting mode, or set to complete a set of startup and
shutdown data, press "MODE" button you can switch to another
group of lights automatically open and close time settings;
G. Set a good boot time or shutdown time, after full power
to save the data.
3) The manual control white light, blue light switch
A. "/ WHITE" button you can manually control the white group
opening and closing, that is, click on "/ WHITE" button will
open the white group, and then click "/ WHITE" button will
close the white group;
B. "-/BLUE" Button you can manually control the opening and
closing Blu-ray group, that is, click on "-/BLUE" button will
open the Blu-ray group, and then click "-/BLUE" button then
close the Blu-ray group.
4) Light temperature detection and protection features
A. Lamps installed on the radiator temperature measurement
probe, the lamp controller, real-time temperature will be
displayed on the screen;
B. When abnormal conditions, such as the cooling fan fails,
or the cooling holes are blocked, heat sink temperature of
60oC, the controller will issue a warning tone, to 70oC, the
internal procedures will automatically cut off the power LED
driver, and maintained fault tips;
C. When the controller to issue over-temperature alarm, should
immediately stop lamps work, to prevent the LED lamp beads
generated due to high temperature damage. And check the lamp
www.aquaportail.com
cooling fan is working properly, has blocked the phenomenon
of cooling holes.
5) Product If you have any unusual conditions or questions,
please contact dealer as soon as possible.
Warranty
MAXSPECT LED Aquarium Lighting product warranty period from
the date of purchase for 18 months.
Warranty does not belong to the following items free of charge
range:
- Consumer handling, installation, use, maintenance, custody
improper damaged.
- Consumer self-apart light body and controller, resulting
in damage to internal parts.
- Consumers provide their own replacement parts to this,
causing all the damage and loss.
- As the product environmental conditions, such as power,
temperature, humidity and other non-company factors beyond
the control of all the damage and losses, are not free of charge
within the warranty.
- After a free warranty period.
- No product warranty certificate.
- Due to force majeure, resulting in product damage.
* Range of products beyond the product warranty repair, the
company will be charged the appropriate fees and related costs
of spare parts.
Attention! Mise en garde.
1) Il est strictement interdit de taper sur les LED lorsqu'elles sont allumées ou de
provoquer des mouvements brusques ou des vibrations à la rampe en cours de
fonctionnement.
2) Le contrôleur de la rampe doit être placé dans un endroit sec et aéré, et ne devrait
pas pouvoir être éclaboussé.
3) Respectez la tension d'entrée 180VAC-245VAC.
www.aquaportail.com
4) L'utilitaire d'installation d'éclairage, s'il vous plaît, lisez attentivement ce manuel
pour éviter de causer un dommage injustifié. S'il vous plaît, conservez ce manuel en
un accès facile.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising