Legrand OptiMo Installation Instruction
Legrand Optimo connectors enable high-performance data transmission through optical fibers. These connectors can be used with 900 µm buffered or loose tube fiber, as well as jacketed fiber. The OptiMo connector provides a secure and reliable connection for your fiber optic applications, supporting various types of fiber, including multimode (50 µm & 62.5 µm) and singlemode.
Iklan
Iklan
OptiMo ® LC, SC and ST Compatible Connectors
OR-71601671
Installation Instructions
OptiMo ® Connector Installation Instructions
OptiMo implies the OptiMo Multimode (50 µm & 62.5 µm) and Singlemode connectors INST REV ECN DWN BY DATE CHK BY DATE APP BY DATE Information subject to change without notice. Ortronics reserves the right to make changes in product design or components as progress in engineering or manufacturing may warrant.
OptiMo
Connector Installation Instructions OptiMo ® is a registered trademark of Ortronics/Legrand Page i
Table of contents
About this guide Safety precautions Installation on 900 µm buffered fiber or loose tube with breakout kit Installation on jacketed fiber Cleaning procedures Fiber Preparation Guide
OptiMo
Connector Installation Instructions 1 33 iv v 64 ANNEX Page iii
About this guide
This guide contains assembly procedures for the OptiMo ® Connector.
Before starting an installation, check to make sure that you have the required tools and materials outlined at the start of the procedure.
Review each procedure to familiarize yourself with the graphic symbols and the actions required.
OR-71601671 Page iv
Safety precautions
CAUTION: • When installed on a live system, invisible laser radiation may be present.
Do not stare into connector endface or view directly with optical instruments.
• Wear safety glasses when working with optical fiber.
• Dispose of all scrap fiber in the waste bottle to avoid getting fiber slivers.
OptiMo
Connector Installation Instructions Page v
Connector components LC
dust cap 900 µm strain relief boot Accessories 2.0 mm
22 m m
3.0 mm connector body Release wire disposable tool dust cap
SC
release wire dust cap Cord adapter crimp sleeves 2.4 mm crimp sleeves strain relief boots strain relief boots 900 µm dust cap connector body disposable tool 3.0 mm jacketed
ST
connector body crimp sleeves 3.0 mm rear housing strain relief boots 900 µm 2.0 mm 3.0 mm front dust cap rear dust cap 2.4 mm jacketed OR-71601671 Page vi
Connector installation tools
multihead adapter table top base fiber cleaver tool clamp
OptiMo ® LC, SC and ST Compatible Connectors OR-71601671
scissors
Installation Instructions
installation manual crimping tool alcohol wipes tweezers universal stripper universal installation tool
OptiMo
Connector Installation Instructions ink marker fiber waste bottle microscope Page vii
Installation on 900 µm buffered fiber or loose tube with breakout kit 1
Open the bag and select the parts required for installation on 900 µm buffered fiber.
(Connector body and 900 µm strain relief boot.)
LC SC ST
connector body with dust caps connector body connector body rear housing 900 µm strain relief boot 900 µm strain relief boot 900 µm strain relief boot
OptiMo
Connector Installation Instructions Page 1
Installation on 900 µm buffered fiber or loose tube with breakout kit 2 a
Install the installation tool on the C clamp as shown, then clamp to the table. The table top base can be used as an alternative.
OR-71601671 Page 2
Installation on 900 µm buffered fiber or loose tube with breakout kit 2 b
Install the multihead adapter on the tool in the appropriate position as illustrated below.
LC position OptiMo
Connector Installation Instructions
SC position ST position
Page 3
Installation on 900 µm buffered fiber or loose tube with breakout kit 3
Load the connector body into the installation tool, with the release wire up.
LC
Leave dust cap on.
SC
Leave dust cap on.
ST
By pushing the housing into the receptacle and turning 1/4 turn clockwise, locking it in place.
Leave dust caps on.
Release wire OR-71601671 Page 4
Installation on 900 µm buffered fiber 4 LC
Slide the boot down the fiber, narrow end first, until it is out of the way.
SC
Slide the boot down the fiber, narrow end first, until it is out of the way.
ST
Slide the 900 µm strain relief boot onto the rear housing until it locks in place.
(Holding the boot on it’s smaller end will ease insertion.) Slide the rear housing with boot down the fiber, narrow end first, until it is out of the way.
OptiMo
Connector Installation Instructions Page 5
Installation: stripping 900 µm tight buffered fiber
(if using
loose tube
with breakout kit,
skip to step 11
)
5
Strip approximately 40 mm of the 900 µm buffered fiber as shown below. Be sure to strip fiber in small (5 mm) sections to avoid breaking it. Buffer end should be clean and square.
* *
If unfamiliar with stripping optical fiber, it is advised to practice using a spare piece of fiber.
Make sure the fiber optic stripper tool you are using is in proper operating condition before attempting this step.
Use of a tool that is not in proper operating condition could cause the fiber to break.
900 µm "V" opening 250 µm "V" opening OR-71601671
Fig. 1 Step 1.
(Fig. 1) Insert fiber into 250 µm "V" opening of the tool.
Fig. 2 Step 2.
(Fig. 2) Close the tool squarely around the fiber.
Fiber waste
Fig. 3 Step 3.
(Fig. 3) Draw the tool along the fiber using thumb pressure while keeping the tool perpendicular to the fiber.
Page 6
Installation: stripping 900 µm tight buffered fiber
(if using
loose tube
with breakout kit,
skip to step 11
)
6
Strip approximately 40 mm of the 900 µm buffered fiber. Be sure to strip fiber in small (5 mm) sections to avoid breaking it. Buffer end should be clean and square. After stripping, measure and mark the buffer from its end as illustrated below.
*
If unfamiliar with stripping optical fiber, it is advised to practice using a spare piece of fiber.
LC
15 mm
SC
11 mm
ST
9 mm
OptiMo
Connector Installation Instructions Fiber waste Page 7
Installation on 900 µm buffered fiber 7
Carefully clean the bare fiber
with a folded alcohol wipe or alcohol soaked lint-free paper. Use two or three passes. Avoid touching the bare fiber, or laying it down on the table, after it has been cleaned.
OR-71601671 Page 8
Pre-Set Cleaver Installation on 900 µm tight buffered fiber
(if using an
adjustable cleaver, skip to step 8b
)
8 a
Cleave the fiber 7 mm from the end of the buffer.
Be sure to read and understand the procedure included with your cleaver that is provided with your Ortronics
®
Field Installation Kit prior to attempting this step
. (The procedure can be downloaded from the Ortronics web site at http://www.legrand.us/ortronics/technicalresources/instruction%20manuals.aspx
)
* *
If unfamiliar with cleaving, it is advised to practice using a spare piece of fiber.
Generally, a light touch is all that is required to score the fiber.
The fiber buffer must rest against the stop.
Alternative cleavers which produce a 7 mm bare fiber length may be used.
OptiMo
Connector Installation Instructions Fiber waste Page 9
Adjustable Cleaver Installation on 900 µm tight buffered fiber 8 b
Cleave the fiber 7 mm from the end of the buffer.
Be sure to read and understand the procedure included with your cleaver that is provided with your Ortronics
®
Field Installation Kit prior to attempting this step
. (The procedure can be downloaded from the Ortronics web site at http://www.legrand.us/ortronics/technicalresources/instruction%20manuals.aspx
)
* *
If unfamiliar with cleaving, it is advised to practice using a spare piece of fiber.
Generally, a light touch is all that is required to score the fiber.
The fiber buffer must be set to produce a 7 mm bare fiber length.
Alternative cleavers which produce a 7 mm bare fiber length may be used.
Fiber waste OR-71601671 Page 10
Installation on 900 µm buffered fiber 9
Cleave the fiber 7 mm from the end of the buffer. Be sure to read and understand the operating instructions included with the cleaver. Using tweezers, discard waste fiber into the proper waste container.
* *
If unfamiliar with cleaving, it is advised to practice using a spare piece of fiber.
Generally, a light touch is all that is required to score the fiber.
The fiber buffer must rest against the stop.
Alternative cleavers which produce a 7 +0.5
-0.0
mm bare fiber length may be used.
OptiMo
Connector Installation Instructions Fiber waste Page 11
Installation on 900 µm buffered fiber 10
Use the microscope to check the quality of the cleave. Pointing the microscope at a white surface will provide a brighter image.
* Note:
If the Ortronics ® Precision Cleave Tool (OR-60300189) is used, cleave inspection with a microscope is not required.
1
Turn microscope over and place fiber on stage.
1 2
Make sure fiber position is as illustrated.
2
OR-71601671 Page 12
Installation on 900 µm buffered fiber 3
Close stage and check fiber. It is recommended to rotate the fiber 90 0 - 180 0 to verify from different angles.
3
Unacceptable cleaves
* Note:
Batteries are not required.
Acceptable cleave
If the cleave is unacceptable, then the fiber must be re-prepared starting from step 5. If fiber or fiber endface appear dirty clean it as in step 6.
Once this step is successfully completed, proceed to step 11
OptiMo
Connector Installation Instructions Page 13
Installation: stripping 900 µm loose tube fiber with breakout kit
(if using
tight buffered, go to step 5
)
11
Strip the 900 µm tube as shown below such that the distance from the end of the tube to the end of the fiber is approximately 40 mm. Tube end should be clean and square.
If unfamiliar with cleaving, it is advised to practice using a spare piece of fiber.
Make sure the fiber optic stripper tool you are using is in proper operating condition before attempting this step.
Use of a tool that is not in proper operating condition could cause the fiber to break.
900 µm "V" opening 250 µm "V" opening
Fig. 1 Step 1.
(Fig. 1) Insert fiber into 900 µm "V" opening of the tool.
OR-71601671
Fig. 2 Step 2.
(Fig. 2) Close the tool squarely around the fiber.
Fiber waste
Fig. 3 Step 3.
(Fig. 3) Draw the tool along the fiber using thumb pressure while keeping the tool perpendicular to the fiber.
Page 14
Installation: stripping 900 µm loose tube fiber with breakout kit 12
Using your fingers, carefully grip the end of the 250 µm coated fiber as shown, and gently push the fiber back into the tube as far as it will go without bending. Tube 250 µm coated fiber
OptiMo
Connector Installation Instructions Page 15
Installation: stripping 900 µm loose tube fiber with breakout kit 13
Position the fiber stripper at the end of the tube, and proceed to remove the 250 µm coating in one even stripping motion as shown in Figures 1 and 2 below. 250 µm coating end should be clean and square. Using your fingers, carefully grip the bare fiber close to the 250 µm coating as shown in Fig. 3 below, and gently push the fiber back into the tube as far as it will go. The 250 µm coating extending beyond the tube as shown in Fig. 4 below.
must always
be visible when the fiber is lightly pushed into the tube. There must be 0.50 mm–1.50 mm of 250 µm coating 250 µm coating tube fiber
Fig. 3 Fig. 1 Step 1.
(Fig. 1) Insert fiber into the 250 µm "V" opening of the tool (shown in previous page). Close the tool squarely around the fiber.
OR-71601671 Fiber waste
Fig. 2 Step 2.
(Fig. 2) Draw the tool along the fiber using thumb pressure while keeping the tool perpendicular to the fiber.
Fig. 4
Page 16
Installation: marking the 900 µm loose tube fiber with breakout kit 14
Place a mark 15 mm from the end of the tube, as shown below.
Tube Mark 250 µm coating 15 mm
OptiMo
Connector Installation Instructions Page 17
Installation: cleaning 900 µm loose tube fiber with breakout kit 15
Carefully clean the bare fiber with a folded alcohol wipe or alcohol soaked lint-free paper. Use two or three passes. Use care not to remove the mark on the tube in the process. Avoid touching the bare fiber, or laying it down on the table, after it has been cleaned.
OR-71601671 Page 18
Pre-Set Cleaver Installation on 900 µm loose tube fiber
(if using an
adjustable cleaver, skip to step 16b
)
16 a
Cleave the fiber 7.0 mm–7.5 mm from the end of the 250 µm coating (not from the end of the tube).
Be sure to read and understand the procedure included with your cleaver that is provided with your Ortronics
®
Field Installation Kit prior to attempting this step.
(The procedure can be downloaded from the Ortronics web site at http://www.legrand.us/ortronics/technicalresources/instruction%20manuals.aspx
)
* * *
If unfamiliar with cleaving, it is advised to practice using a spare piece of fiber.
Generally, a light touch is all that is required to score the fiber.
The 250 µm coating must rest against the stop.
Alternative cleavers which produce a 7 +0.5
-0.0
mm bare fiber length may be used.
After cleaving, there must still be 0.50 mm–1.50 mm of 250 µm coating extending beyond the tube as shown. If required, using your fingers, carefully grip the bare fiber close to the 250 µm coating as shown in Fig. 3 of step 13, and gently push the fiber back into the tube as far as it will go. The 250 µm coating must always be visible when the fiber is lightly pushed into the tube.
OptiMo
Connector Installation Instructions Fiber waste Page 19
Adjustable Cleaver Installation on 900 µm loose tube fiber 16 b
Cleave the fiber 7.0 mm–7.5 mm from the end of the 250 µm coating (not from the end of the tube).
Be sure to read and understand the procedure included with your cleaver that is provided with your Ortronics
®
Field Installation Kit prior to attempting this step.
(The procedure can be downloaded from the Ortronics web site at http://www.legrand.us/ortronics/technicalresources/instruction%20manuals.aspx
)
* * *
If unfamiliar with cleaving, it is advised to practice using a spare piece of fiber.
Generally, a light touch is all that is required to score the fiber.
The 250 µm coating must be set to produce a 7 +0.5
-0.0
mm bare fiber length.
Alternative cleavers which produce a 7 mm bare fiber length may be used.
After cleaving, there must still be 0.50 mm–1.50 mm of 250 µm coating extending beyond the tube as shown. If required, using your fingers, carefully grip the bare fiber close to the 250 µm coating as shown in Fig. 3 of step 13, and gently push the fiber back into the tube as far as it will go. The 250 µm coating must always be visible when the fiber is lightly pushed into the tube.
Fiber waste OR-71601671 Page 20
Installation: cleave inspection of 900 µm loose tube fiber 17
Use the microscope to check the quality of the cleave. Pointing the microscope at a white surface will provide a brighter image. If the cleave is unacceptable, then the fiber must be re-prepared starting from step 11. If fiber or fiber end-face appears dirty, reclean fiber as in step 15.
1
Turn microscope over and place fiber on stage.
2
Make sure fiber position is as illustrated.
3
Close stage and check fiber.
4
Slowly adjust focus knob until fiber profile is clear.
5
It is recommended to rotate the fiber 90˚ - 180˚ to verify different angles
* Note:
Batteries are not required. If the Ortronics ® Precision Cleave Tool (OR-60300189) is used, cleave inspection with a microscope is not required.
OptiMo
Connector Installation Instructions
3 2 1
Unacceptable cleaves Acceptable cleave
Page 21
Installation on 900 µm tight buffered fiber or loose tube with breakout kit 18
Break dust cap from the disposable tool. Discard.
OR-71601671 Page 22
Installation on 900 µm tight buffered fiber or loose tube with breakout kit 19
Carefully insert the bare fiber into the stem of the connector until you feel the end of the fiber touch the fiber stub inside the connector. Gently rotating the fiber between your thumb and forefinger may ease insertion. DO NOT rotate or remove the fiber once fully inserted into the connector. When fully inserted, the pen mark on the buffer should be near the edge of the connector stem. Clamp the fiber into the installation tool clamp as shown in Fig. 1. In order to ensure that the fiber end face being installed maintains contact with the fiber end face inside the connector during subsequent handling, there MUST BE a bow of approximately 15 mm–20 mm (0.6 in.–0.75 in.) as illustrated.
Pen mark Installation Tool Fiber Clamp 15 mm–20 mm (0.6 in.–0.75 in.) Figure 1 Page 23
OptiMo
Connector Installation Instructions
Installation on 900 µm tight buffered fiber or loose tube with breakout kit 20
Depress the installation tool plunger. Ensure it hooks the release wire, then
slowly
Discard the release wire.
release the plunger. Release wire OR-71601671 Page 24
Installation on 900 µm buffered fiber 21 LC
Break dust cap from disposable tool and discard it.
SC
Break dust cap from disposable tool and discard it.
ST
Remove rear dust cap from connector body. Discard.
OptiMo
Connector Installation Instructions Page 25
Installation on 900 µm tight buffered fiber or loose tube with breakout kit 22
Carefully insert the bare fiber into the stem of the connector until you feel the end of the fiber touch the fiber stub inside the connector. Gently rotating the fiber between your thumb and forefinger may ease insertion. DO NOT rotate or remove the fiber once fully inserted into the connector. When fully inserted, the pen mark on the buffer should be near the edge of the connector stem. Clamp the fiber into the installation tool clamp as shown in Fig. 1. In order to ensure that the fiber end face being installed maintains contact with the fiber end face inside the connector during subsequent handling, there MUST BE a bow of approximately 15 mm–20 mm (0.6 in.–0.75 in.) as illustrated.
Pen mark Installation Tool Fiber Clamp 15 mm–20 mm (0.6 in.–0.75 in.) Figure 1 Page 26 OR-71601671
Installation on 900 µm buffered fiber 23
Carefully insert the bare fiber into the stem of the connector until you feel the
fibers make contact
of the fibers.
. Gently twisting the fiber may ease insertion. Do not twist or remove the fiber once it is fully inserted. When fully inserted, the pen mark on the buffer should be near the edge of the stem of the connector. Clamp the fiber into the clamp of the installation tool. There must be a bow of approximately 15mm-20mm (0.6in 0.75in) as illustrated in the fiber in order to maintain a contact between the end faces clamp
LC
Pen mark
SC ST
Pen mark Pen mark Page 27
OptiMo
Connector Installation Instructions
Installation on 900 µm buffered fiber 24
Depress the installation tool plunger. Ensure it hooks the release wire, then
slowly
release the plunger.
LC SC ST
Release wire Release wire Release wire Page 28 OR-71601671
Installation on 900 µm buffered fiber 25
Unclamp the fiber.
Carefully
remove the connector from the installation tool. Hold the crimping tool horizontally and close it partially. Load the connector into the first and smallest die (.068 hex) of the crimping tool as shown with the disposable tool tab pointing at the crimping tool handle. The smallest diameter hex face is against the disposable tool tab. Crimp firmly until tool release latch opens.
*
Make sure that the crimp tool you are using is in proper operating condition before attempting this step. Also make sure that the tool is set to the settings shown in the Technical Bulletin—OptiMo ® Field Installable Connectors document that is provided with your Ortronics ® Field Installation Kit.
(The document can be downloaded from the Ortronics web site at http://www.legrand.us/ortronics/technicalresources/instruction%20manuals.aspx
)
LC SC ST
Buffer crimp area Buffer crimp area Buffer crimp area
OptiMo
Connector Installation Instructions Page 29
Installation on 900 µm buffered fiber 26 a LC
Remove disposable tool and discard it.
Holding the boot by its collar
, align the anti snag with the latch of the LC connector, slide it onto the rear of the connector until its step reaches the connector body. The installation is now completed.
*
Be sure to clean the connector as described in the “Cleaning Procedures” section before using the connector.
SC
Grab the disposable tool as shown. Pull until a click is heard. Remove the tool and discard it.
ST
Align and press the rear housing with boot into the front housing until a click is heard.
The installation is now complete.
*
Be sure to clean the connector as described in the “Cleaning Procedures” section before using the connector.
OR-71601671 Page 30
SC 26 b Installation on 900 µm buffered fiber
Holding the boot by its collar
, slide it onto the rear of the connector until its step reaches the connector body. The installation is now completed.
*
Be sure to clean the connector as described in the “Cleaning Procedures” section before using the connector (See page 64).
SC only OptiMo
Connector Installation Instructions Page 31
Notes
OR-71601671 Page 32
Installation on jacketed fiber 1 LC
Open the connector bag and the accessories bag. Select the appropriate parts required for installation on 2.0mm or 3.0mm jacketed fiber. (Connector body, crimp sleeve and strain relief boot)
SC 1a)
Before you start an installation on jacketed fiber, you need to determine the installation method (there are two) and the parts you are going to need. You simply have to determine the outer diameter of the cable jacket you are installing the connector on.
ST
Open Open the bag of materials and take out the connector body and the rear housing. In order to select the crimp sleeve, you need to first determine the outer diameter of the cable jacket you are installing. The appropriate crimp sleeve for a cord, size from 2.0 mm to 2.4 mm is the 2.4
mm sleeve. For a cord size from 2.5 mm to 3.0 mm, use the 3.0 mm crimp sleeve. Accessories 2.0 mm 3.0 mm crimp sleeves connector body connector body 2.4 mm connector body strain relief boots 2.0 mm Cord adapter 3.0 mm 3.0 mm 3mm strain relief boots crimp sleeves 3.0 mm crimp sleeves 2.4 mm rear housing 3mm strain relief boots
OptiMo
Connector Installation Instructions Page 33
Installation on jacketed fiber 2 a
Install the installation tool on the C clamp as shown, then clamp to the table. The table top base can be used as an alternative.
OR-71601671 Page 34
Installation on jacketed fiber 2 b
Install the multihead adapter on the tool in the appropriate position as illustrated below.
LC position OptiMo
Connector Installation Instructions
SC position ST position
Page 35
Installation on jacketed fiber 3
Load the connector body into the installation tool, with the release wire up.
LC
Leave dust cap on.
SC
Leave dust cap on.
ST
By pushing the housing into the receptacle and turning 1/4 turn clockwise, locking it in place.
Leave dust caps on.
Release wire OR-71601671 Page 36
Installation on jacketed fiber 4 LC
Slide the boot down the fiber, narrow end first, until it is out of the way.
SC
Slide the boot down the fiber, narrow end first, until it is out of the way.
ST
Slide the strain relief boot onto the rear housing until it locks in place. (Holding the boot on its smaller end will ease insertion.) Slide the rear housing with boot, narrow end first.
OptiMo
Connector Installation Instructions Page 37
Installation on jacketed fiber 5
Using the universal stripper as shown cut squarely and remove 50 mm of the outer jacket from the end of the cord. The jacket must be cut cleanly and square.
OR-71601671 Fiber waste Page 38
Installation on jacketed fiber 6
Insert the crimp sleeve down the fiber approx. 30 mm from the edge of the jacket, hold the Kevlar with the crimp sleeve.
LC
3 mm 2 mm
SC
3 mm 2.4 mm
ST
3 mm 2.4 mm
OptiMo
Connector Installation Instructions Page 39
LC 7 Installation on jacketed fiber
Make sure all the slack fiber is pushed back inside the jacket.
First mark the buffer at the end of the jacket. Then mark it again at 16 mm.
LC
16 mm OR-71601671 Page 40
SC Installation on jacketed fiber 8 a For 2.0 mm to smaller than 2.4 mm cord 8 b For 2.4 mm to 3.0 mm cord
Make sure all the slack fiber is pushed back inside the jacket
. First mark the buffer at the end of the jacket.
Mark it again at 6 mm and 17 mm.
Make sure all the slack fiber is pushed back inside the jacket
. Insert the cord adapter as shown. First mark the buffer at the end of the cord adapter. Mark it again at 4 mm and 15 mm.
SC
6 mm 17 mm
OptiMo
Connector Installation Instructions 4 mm 15 mm Page 41
ST 9 Installation on jacketed fiber
Make sure all the slack fiber is pushed back inside the jacket.
First mark the buffer at the end of the jacket. Then mark it again at 11 mm.
ST
11 mm OR-71601671 Page 42
Installation on jacketed fiber 10
Hold the fiber on the exposed buffer section. Strip the fiber to the mark. Be sure to strip the buffer from the fiber in small (5 mm) sections to avoid breaking the fiber.
LC
16 mm
SC For 2.0 mm to smaller than 2.4 mm cord ST
17 mm
For 2.4 mm to 3.0 mm cord
15 mm
*
If unfamiliar with stripping optical fiber, it is advised to practice using a spare piece of fiber.
OptiMo
Connector Installation Instructions 11 mm Page 43
Installation on jacketed fiber 11
Carefully clean the bare fiber
with a folded alcohol wipe or alcohol soaked lint-free paper. Use two or three passes. Avoid touching the bare fiber, or laying it down on the table, after it has been cleaned.
OR-71601671 Page 44
Pre-Set Cleaver Installation on jacketed fiber 12 a
Cleave the fiber 7 mm from the end of the buffer.
Be sure to read and understand the procedure included with your cleaver that is provided with your Ortronics
®
Field Installation Kit prior to attempting this step.
(The procedure can be downloaded from the Ortronics web site at http://www.legrand.us/ortronics/technicalresources/instruction%20manuals.aspx
)
* *
If unfamiliar with cleaving, it is advised to practice using a spare piece of fiber.
Generally, a light touch is all that is required to score the fiber.
The fiber buffer must rest against the stop.
Alternative cleavers which produce a 7 +0.5
-0.0
mm bare fiber length may be used.
OptiMo
Connector Installation Instructions Fiber waste Page 45
Adjustable Cleaver Installation on jacketed fiber 12 b
Cleave the fiber 7 mm from the end of the buffer.
Be sure to read and understand the procedure included with your cleaver that is provided with your Ortronics
®
Field Installation Kit prior to attempting this step.
(The procedure can be downloaded from the Ortronics web site at http://www.legrand.us/ortronics/technicalresources/instruction%20manuals.aspx
)
*
If unfamiliar with cleaving, it is advised to practice using a spare piece of fiber.
Generally, a light touch is all that is required to score the fiber
. The fiber buffer must be set to produce a 7 mm bare fiber length.
*
Alternative cleavers which produce a 7 mm bare fiber length may be used.
OR-71601671 Fiber waste Page 46
Installation on jacketed fiber using preset cleaver 13
Press the buffer into place on the cleaver, and cleave the fiber 7 mm from the end of the buffer. Be sure to read and understand the operating instructions included with the cleaver. Using tweezers, discard waste fiber into the proper waste container.
* *
If unfamiliar with cleaving, it is advised to practice using a spare piece of fiber.
Generally, a light touch is all that is required to score the fiber.
The fiber buffer must rest against the stop.
Alternative cleavers which produce a 7 mm bare fiber length may be used.
OptiMo
Connector Installation Instructions Fiber waste Page 47
Installation on jacketed fiber 14
Use the microscope to check the quality of the cleave. Pointing the microscope at a white surface will provide a brighter image.
* Note:
If the Ortronics ® Precision Cleave Tool (OR-60300189) is used, cleave inspection with a microscope is not required.
1
Turn microscope over and place fiber on stage.
1 2
Make sure fiber position is as illustrated.
2
OR-71601671 Page 48
Installation on jacketed fiber 3
Close stage and check fiber. It is recommended to rotate the fiber 90 0 - 180 0 to verify from different angles.
Unacceptable cleaves
3 * Note:
Batteries are not required.
Acceptable cleave
If the cleave is unacceptable, then the fiber must be re-prepared starting from step 5. If fiber or fiber endface appear dirty, clean it as in step 11.
OptiMo
Connector Installation Instructions Page 49
Installation on jacketed fiber 15 LC
Break dust cap from disposable tool and discard it.
SC
Break dust cap from disposable tool and discard it.
ST
Remove rear dust cap from connector body. Discard.
OR-71601671 Page 50
Installation on jacketed fiber 16
Carefully insert the bare fiber into the stem of the connector until you feel the fibers make contact. Gently twisting the fiber may ease insertion. Do not twist or remove the fiber once it is fully inserted. When fully inserted, the pen mark on the buffer should be near the edge of the stem of the connector. Clamp the fiber into the clamp of the installation tool. Must be a bow of approximately 15mm-20mm to maintain a contact between the end faces of the fibers.
LC
Max. 1mm
SC ST
Max. 2 mm Pen mark
OptiMo
Connector Installation Instructions Page 51
Installation on jacketed fiber 17
Depress the installation tool plunger. Ensure it hooks the release wire, then
slowly
release the plunger.
LC SC ST
Release wire Release wire Release wire OR-71601671 Page 52
LC 18 Installation on jacketed fiber
Unclamp the cord.
Carefully
remove the connector from the installation tool. Hold the crimping tool vertically and rest the crimping tool against the disposable tool tab to ensure it is aligned properly. The disposable tool must be rotated in order for it’s tab to be pointing at the crimp tool handle. Using the first and smallesr die (,068 hex) on the crimping tool, strongly crimp the stem on the buffer at the “buffer crimp area”, making sure neither the jacket nor any aramid yarn is in the way. The smallest diameter hex face is against the disposable tool tab.
*
Make sure that the crimp tool you are using is in proper operating condition before attempting this step. Also make sure that the tool is set to the settings shown in the Technical Bulletin—OptiMo ® Field Installable Connectors document that is provided with your Ortronics ® Field Installation Kit.
(The document can be downloaded from the Ortronics web site at http://www.legrand.us/ortronics/technicalresources/instruction%20manuals.aspx
) Buffer crimp area
OptiMo
Connector Installation Instructions Page 53
LC Installation on jacketed fiber 19
Remove disposable tool and discard it. Gently pull the Kevlar towards the connector to make sure there is no slack. Slide the crimp sleeve over the Kevlar. Spread the Kevlar evenly around the connector.
Carefully
remove the connector from the installation tool. Ensure the crimp sleeve is against the rear of the connector and strongly crimp the crimp sleeve using the middle die (.128 hex) of the crimping tool. Now you can cut excess aramid yarn.
OR-71601671 Page 54
LC Installation on jacketed fiber 20
Holding the boot by its collar
, align the anti snag with the latch of the LC connector, slide it onto the rear of the connector until its step reaches the connector body. The installation is now completed.
*
Be sure to clean the connector as described in the “Cleaning Procedures” section before using the connector (See page 64).
OptiMo
Connector Installation Instructions Page 55
SC Installation on jacketed fiber 21
Rest the crimping tool against the disposable tool tab to ensure it is aligned properly. The disposable tool must be rotated in order for it’s tab to be pointing at the crimp tool handle. Using the first and smallest die (.068 hex) on the crimping tool, strongly crimp the stem on the buffer at the “buffer crimp area”, making sure neither the jacket nor any aramid yarn is in the way. The smallest diameter hex face is against the disposable tool tab.
*
Make sure that the crimp tool you are using is in proper operating condition before attempting this step. Also make sure that the tool is set to the settings shown in the Technical Bulletin—OptiMo ® Field Installable Connectors document that is provided with your Ortronics ® Field Installation Kit.
(The document can be downloaded from the Ortronics web site at http://www.legrand.us/ortronics/technicalresources/instruction%20manuals.aspx
) OR-71601671 Buffer crimp area Page 56
SC 22 Installation on jacketed fiber
Grab the disposable tool as shown. Pull in order to expose approximately 8 mm of the sliding part
and until a click is heard
. During this operation, if you are using the cord adaptor, hold it carefully and facilitate its mating with the sliding part. Remove the tool and discard it.
OptiMo
Connector Installation Instructions Page 57
SC Installation on jacketed fiber 23
Slide the crimp sleeve farther down the fiber to release the aramid yarn. Gently pull the aramid yarn towards the connector to make sure there is no slack. Slide the crimp sleeve over the aramid yarn. Spread the aramid yarn evenly around the connector.
Carefully
remove the connector from the installation tool. Ensure the crimp sleeve is against the rear of the connector and strongly crimp the crimp sleeve using the middle die (.128 hex) of the crimping tool. Now you can cut excess aramid yarn.
OR-71601671 Page 58
SC 24 Installation on jacketed fiber
Holding the boot on its ribbed section
, slide it onto the rear of the connector until it snaps in place. The installation is now complete.
*
Be sure to clean the connector as described in the “Cleaning Procedures” section before using the connector (See page 64).
OptiMo
Connector Installation Instructions Page 59
ST Installation on jacketed fiber 25
Disengage coupling nut by pushing and rotating the connector body 1/4 turn counterclockwise in order to unlock the connector from the installation tool. Rest the crimping tool against the connector body to ensure it is aligned properly. Using the first and smallest die (.068 hex) on the crimping tool, crimp strongly the stem on the buffer at the “buffer crimp area”, making sure neither the jacket nor any aramid yarn is in the way. The smallest diameter hex face is against the rear of the connector.
*
Make sure that the crimp tool you are using is in proper operating condition before attempting this step. Also make sure that the tool is set to the settings shown in the Technical Bulletin—OptiMo ® Field Installable Connectors document that is provided with your Ortronics ® Field Installation Kit.
(The document can be downloaded from the Ortronics web site at http://www.legrand.us/ortronics/technicalresources/instruction%20manuals.aspx
) Buffer crimp area OR-71601671 Page 60
ST Installation on jacketed fiber 26
Reinsert the connector in the installation tool and lock it in place. Turn the connector body housing 1/8 turn counterclockwise so the housing is resting as shown.
1/8 turn
OptiMo
Connector Installation Instructions Page 61
ST 27 Installation on jacketed fiber
Slide the crimp sleeve farther down the fiber to release the aramid yarn. Gently cut the aramid yarn ensuring that it reaches the end of the connector body.
Spread the aramid yarn evenly around the stem of the connector
. Slide the crimp sleeve down the fiber toward the connector. Ensure the crimp sleeve is against the retaining ring at the rear of the connector body and strongly crimp the crimp sleeve using the middle die (.128 hex) of the crimping tool.
OR-71601671 Page 62
ST Installation on jacketed fiber 28
Unclamp the cord. Align and press the rear housing with boot into the front housing until a click is heard. Remove the connector from the installation tool. The installation is now complete.
*
Be sure to clean the connector as described in the “Cleaning Procedures” section before using the connector.
OptiMo
Connector Installation Instructions Page 63
Cleaning procedures
1. Wipe completely around the connector ferrule a few times with a lint-free alcohol soaked wipe. Then wipe across the end of the ferrule.
2. Repeat step 1 with a dry wipe.
3. Blow compressed gas across the end of the ferrule (optional but recommended).
* * *
Do not allow ferrule to touch anything before inserting into coupling.
Preferred alcohol is ethanol but isopropyl alcohol may be used.
A dry cleaning tape system may also be used.
OR-71601671 Page 64
Notes OptiMo
Connector Installation Instructions Page 65
Fiber Preparation Guide OptiMo ® LC
Fiber Preparation Guide (for Multimode and Singlemode)
900 µm buffered fiber Jacketed fiber NOT T O SC ALE *Reproductions of the above guide generated from this PDF may not be to scale.
OptiMo
LC Connector Installation Instructions
Fiber Preparation Guide OptiMo ® SC
Fiber Preparation Guide (for Multimode and Singlemode)
900 µm buffered fiber 2.4 mm cord or larger Smaller than 2.4 mm cord NOT T O SC ALE *Reproductions of the above guide generated from this PDF may not be to scale.
OptiMo
SC Connector Installation Instructions
Fiber Preparation Guide OptiMo ® ST-Type
Fiber Preparation Guide (for Multimode and Singlemode)
900 µm buffered fiber Jacketed fiber NOT T O SC ALE *Reproductions of the above guide generated from this PDF may not be to scale.
OptiMo
ST Connector Installation Instructions
http://www.legrand.us/ortronics 800-934-5432
OptiMo
®
high performance fiber optic solutions
Unduh
Tautan publik diperbarui
Tautan publik ke obrolan Anda telah diperbarui. You may view and manage your chat links after registration here.
Tautan publik dokumen
Iklan