Legrand LMPS-6000 Skylight Photocell Installation Instruction

Legrand LMPS-6000 Skylight Photocell Installation Instruction
LMPS-6000
Skylight Photocell
for Digital Lighting Management (DLM)
INSTALLATION
Install the sensor on the side wall of the skylight well
as shown in the Wiring diagram. The sensor housing is
equipped with a ½" NPT nipple and will thread into any
suitable box or fitting, or mount into a ½" knockout. This
sensor is also suitable for use in atrium or clerestory
applications where high sunlight levels are common.
MAINTENANCE
At least once every two months wipe the lens clean
with a non-scratching clean cloth. Check the housing
for damage and that no moisture has penetrated the
sensor, as this will likely render it inoperable.
DLM Local Network
Example 1
LMPS-6000
Skylight
Photocell
LMIO-301
SPECIFICATIONS:
Footcandle range LMPS-6000 . . . . . . . . . . . 24 - 6000 fc
Calibration . . . . . .None, controlled by system software
Input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24VDC
Sensor output . . . . . . . . . . . . . . . . . . . . . . . . . . 1-10VDC
Peak current . . . . . . . . . . . . . . . . . . . .4.5 mA Maximum
Slew rate . . . . .1 minute full scale response time filter
Operating temperature -40˚F to 140˚F (-40˚C to 60˚C)
Wire color code
Red . . . . . . . . . . . . . . . . . . . . Input Voltage +24 VDC
Black . . . . . . . . . . . Input Return/Output Common
Yellow . . . . . . . . . . . . . . . . . 1-10VDC Output Signal
Housing
UV stabilized plastic with dome lens
Mounting . . . . . . . . . . . . . . . . . . . . . ½" NPT x .69" stem
Overall dimensions . . . . . . . . . . . . .2.55"L x 1.28"D
Line Voltage
WIRING
LMRJ Cables
Switch
Connect the sensor to the LMIO-301 as shown.
LMRC-3xx
Room Controller
w/ Network
J-Box
Bridge
0-10 Volt
Ballast
0-10 Volt
Ballast
Skylight
Well
LM-MSTP Wire
Occupancy Sensor
Vertical
Orientation
Option
Segment Manager
or BACnet BAS
Example 2
LMPS-6000
Skylight
Photocell
LMIO-301
LMPS-6000
Skylight Photocell
LMRC-102
Room
Controller
Line Voltage
1
LMRJ Cables
#20 AWG up to 250 feet
#18 AWG up to 1000 feet
Class 2 wiring
2
J-Box
Switch
LM-MSTP
Wire
LMIO-301
Loads
LMIO-301 Terminals
1
2
3
4
5
6
7
8
9
10
Segment Manager
or BACnet BAS
Common (Black)
Occupancy Sensor
+24VDC Input Voltage (Red)
1-10VDC Output Signal (Yellow)
LMBC-300
Network Bridge
2800 De La Cruz Blvd.
Santa Clara, CA 95050
Phone: 800.879.8585
www.wattstopper.com
6/2010
13822r1
Please
Recycle
Installation Instructions
DESCRIPTION
The LMPS-6000 is a daylight sensor specifically
designed to be used in conjunction with a LMIO-301
DLM Photocell Input Module. The LMIO-301 converts
the 10 VDC signal from the photocell sensor to a digital
signal that is shared across the DLM Local Network.
The signal is forwarded as a BACnet object via a DLM
network bridge to the segment network for load control
via a DLM segment manager or BACnet compatible
Building Automation System (BAS).
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement