Digital Watchdog DWC-MB44Wi650 MEGApix® 4MP Bullet IP Camera Installation Guide

Digital Watchdog DWC-MB44Wi650 MEGApix® 4MP Bullet IP Camera Installation Guide
Quick Start Guide
Quick Start Guide
STEP 1 – PREPARING TO MOUNT THE CAMERA
STEP 3 – INSTALLING THE CAMERA
1. The mounting surface must bear five times the weight of your camera.
1. Once all cables are connected, secure the camera to the mounting
surface using the included screws.
2. Loosen the pan and tilt screws at the base of the camera’s bracket
to adjust the camera’s view and position.
2. Do not let the cables get caught in improper places or the electric
line cover to be damaged. This may cause a breakdown or fire.
DWC-MB44Wi650
3. CAUTION: These servicing instructions are for use by qualified
service personnel only. To reduce the risk of electric shock do not
perform any servicing other than that contained in the operating
instructions unless you are qualified to do so.
4. This product is intended to be supplied by a UL Listed Power
Supply Unit marked “Class 2” or “LPS” or “PS2” and rated 12 Vdc,
920 mA min.
5. The wired LAN hub providing power over the Ethernet (PoE) in
accordance with IEEE 802-3af shall be a UL Listed device with
the output evaluated as a Limited Power Source as defined in
UL60950-1 or PS2 as defined in UL62368-1.
Password: admin
1 Set
1
Torque wrench
1
Pass the wires through and make all necessary connections.
1
DC Plug Cable
1
1. NETWORK CONNECTIONS – Using a PoE Switch or PoE Injector,
connect the camera using an Ethernet cable for both data and
power.
Mounting
template
Test video
cable
Waterproof
cap
1 Set
NOTE: Download all your support materials and tools in one place
1. Go to: http://www.digital-watchdog.com/resources
2. Search your product by entering the part number in the
‘Search by Product’ search bar. Results for applicable
part numbers will populate automatically based on the
part number you enter.
3. Click ‘Search’. All supported materials, including manuals
and quick start guide (QSGs) will appear in the results.
Attention: This document is intended to serve as a quick reference for initial
set-up. It is recommended that the user read the entire instruction manual for
complete and proper installation and usage.
Tel: +1 (866) 446-3595 / (813) 888-9555
Technical Support Hours:
9:00AM – 8:00PM EST, Monday thru Friday
b.
with a 1/4 turn.
b
will be assembled to
c. Thread
c
tightly to
b
a
.
.
NOTE: To ensure moisture seal, make sure the o-ring is in place
between a and b . In extreme environments use of an
outdoor rated sealer is recommended.
Reset Button
c
Zoom Lens
Button
SD Card
Input
b
Screws and
plastic
anchors – 4pcs
1
a
7. Using the mounting template sheet or the camera itself, mark and
drill the necessary holes in the wall or ceiling.
WHAT’S IN THE BOX
Quick setup
guide
a. Install the LAN cable into
6. Unit is intended for installation in a Network Environment 0 as
defined in IEC TR 62102. As such, associated Ethernet wiring shall
be limited to inside the building.
Default Login Information
Username: admin
3. To use the camera’s water proof wiring:
digital-watchdog.com
STEP 2 – CABLING THE CAMERA TO
EXTERNAL DEVICES
2. NETWORK CONNECTIONS – Not using PoE Switch or PoE
Injector, connect the camera to the switch using an Ethernet
cable for data transmission and use a power adapter to power the
camera.
Power requirements
Power consumption
DC12V, PoE
(IEEE 802.3af class 3).
Adapter not Included.
DC12V: Max 11W
PoE: Max 12.9W
a
Test Video
Output
NOTE: When using the waterproof cap, crimp the RJ45
connector after passing the cable through the
waterproof cap.
3. Loosen the pan and tilt screws at the base of the camera’s bracket
to adjust the camera’s view and position.
Resetting the camera: To reset the camera, use the tip of a
paper clip or a pencil and press the reset button. Pressing the
button for five (5) seconds will initiate a camera-wide reset of
all the settings, including network settings.
Quick Start Guide
STEP 7 – WEB VIEWER
STEP 4 – CABLING
STEP 6 – DW IP FINDER™
Use the diagram below to properly connect power, network, audio,
alarm and sensors to the camera.
Use the DW IP Finder™ software to scan the network and detect all MEGApix ® cameras, set the camera’s network settings or access the camera’s web client.
Thumbnail view
Using a PoE Switch or PoE
Injector
Not using PoE Switch or PoE
Injector
Firmware version
Select network to scan
Camera’s uptime
Filter device type to scan
Scan devices
Ethernet cable
Ethernet cable
Show/hide thumbnail view
Open Device
Refresh thumbnail view
configuration
*
settings
The GUI display may differ by camera models.
Power
DI: Orange
DI COM: Yellow
DO1(N.O.): Green
DO1 COM: Blue
Once the camera’s network settings have been setup properly, you
can access the camera’s web viewer using the DW IP Finder ™.
Bulk IP assignment
Device’s
information
4 Alarm In
Firmware upgrade
To open the camera’s web viewer:
1. Find the camera using the DW IP Finder ™.
2. Double-click on the camera’s view in the results table.
3 Alarm Out
3. Press the ‘View Camera Website’. The camera’s web viewer will
open up in your default web browser.
4. Enter the camera’s username and password (default are admin / admin).
1 Audio In
(WHITE Jack)
2 Audio Out
(RED Jack)
STEP 5 – MANAGING THE SD CARD
1. To install the camera’s SD Card, locate the SD card slot in the
bottom of the camera by unscrewing the con cap.
2. Insert class 10 SD/SDHC/SDXC card into the SD card slot by
pressing the SD card until clicks.
3. To remove the SD card, press the card inward until it clicks to
release from the card slot than pull out from the slot.
Network Setup
1.
To install the DW IP Finder™, go to: http://www.digital-watchdog.com
2. Enter “DW IP Finder” on the search box at the top of the page
and press Enter.
3. Click on the DW IP Finder from the search result and go to
Software tab. Click on download icon to download the DW IP
Finder installation file.
4. Run the installation file and follow the wizard to install the DW
IP Finder™. Open the DW IP Finder™ and click ‘Scan Devices’. It
will scan the selected network for all supported devices and list
the results in the table. During the scan, the DW logo will
turn gray.
Select DHCP if the internet service is dynamic IP. This will allow the
camera to receive its IP address from the DHCP server.
Select “Static” to manually enter the camera’s IP address, (Sub)
Netmask, Gateway and DNS information.
* The camera’s IP must be set to Static if connecting to
DW Spectrum
Contact your network administrator for more information.
NOTE: Maximum SD Card size supported: 64GB.
When inserting the SD card into the card slot, the SD
card’s contacts should be facing upward, as shown in
the diagram.
5.
6.
7.
Select a camera from the list by double-clicking on the
camera’s image or clicking on the ‘Click’ button under the
IP Conf. column. The pop-up window will show the camera’s
current network settings, allowing admin users to adjust the
settings as needed.
To access the camera’s web page, click on ‘View Camera Website’.
To save the changes made to the
camera’s setting, input username and
password of the camera and click Apply.
Click “Scan Devices” from the main screen again to display the
updated information.
5. If you are accessing the camera for the first time, install the VLC
player for web files in order to view video from the camera.
* NOTE: Some Menu options may not be available based on the
camera model. See the full manual for more information.
NOTE: Please see the full product manual for web viewer setup,
functions and camera settings options.
‘Port forwarding’ has to be set in your
network’s router for external access
to the camera.
Default ID / PW : admin / admin
*NOTE: For security purposes, it is highly
recommended to change your
password after initial setup.
Default TCP/IP information: DHCP
Rev Date: 04/19
Copyright © Digital Watchdog. All rights reserved.
Specifications and pricing are subject to change without notice.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement