Danfoss VLT AutomationDrive FC 302 Guide

MAKING MODERN LIVING POSSIBLE
Operating Instructions
VLT® PROFIBUS Converter MCA 114
VLT® AutomationDrive FC 302 • VLT® 5000
www.danfoss.com/drives
VLT® AutomationDrive FC 302 PROFIBUS Converter Operating Instructions
Contents
Contents
1 Introduction
3
1.1 About this Manual
3
1.2 Technical Overview
3
1.3 Constraints
3
1.3.1 Software Versions
3
1.3.2 Relations
4
1.3.3 Hardware
4
1.3.4 Performance
5
1.4 Abbreviations
5
2 Safety
6
3 How to Install
7
3.1 Connecting the Bus Line
7
3.2 How to Install Option in Frequency Converter
7
3.2.1 Mechanical Installation
3.3 EMC Precautions
8
8
4 How to Configure the System
4.1 Configure the PROFIBUS Network
9
9
4.1.1 Setting the PROFIBUS Address using the Hardware Switches
9
4.1.2 Setting the PROFIBUS Address via 9-18 Node Address
9
4.1.3 Commissioning
10
4.2 LED Behaviour
10
4.3 Initialisation
11
5 Parameter Mapping Lists
12
5.1 VLT® 5000 Parameter Group 0
12
5.2 VLT® 5000 Parameter Group 1
14
5.3 VLT® 5000 Parameter Group 2
18
5.4 VLT® 5000 Parameter Group 3
21
5.5 VLT® 5000 Parameter Group 4
29
5.6 VLT® 5000 Parameter Group 5
34
5.7 VLT® 5000 Parameter Group 6
36
5.8 VLT® 5000 Parameter Group 7
38
5.9 VLT® 5000 Parameter Group 8
39
5.10 VLT® 5000 Parameter Group 9
40
6 Troubleshooting
43
6.1 Step-by-step Troubleshooting
MG34N202 - Rev. 2013-10-15
43
1
VLT® AutomationDrive FC 302 PROFIBUS Converter Operating Instructions
Contents
Index
2
44
MG34N202 - Rev. 2013-10-15
Introduction
VLT® AutomationDrive FC 302 PROFIBUS Converter Operating Instructions
1 1
1 Introduction
NOTICE
1.1 About this Manual
First-time users can find the most essential information for
quick installation and set-up in these chapters:
1.2.1 Technical Overview
1.3 Constraints
3 How to Install
For more detailed information including the full range of
set-up options and diagnosis tools, refer to:
4 How to Configure the System
5 Parameter Mapping Lists
1.1.1 FC 300-related Literature
The following literature is available for the FC 300 series:
•
VLT® AutomationDrive FC 302 Operating
Instructions
•
•
VLT® AutomationDrive FC 302 Design Guide
VLT® AutomationDrive FC 302 Programming
Guide
www.danfoss.com/BusinessAreas/DrivesSolutions/Documentations/VLT+Technical+Documentation.htm
1.2 Technical Overview
The MCA 114 Profibus Converter is an option replacing a
VLT® 5000 with a VLT® AutomationDrive FC 302 in a
PROFIBUS network.
Some parameters in the VLT® 5000 are not supported in
the FC 302 and some FC 302 parameters cannot be
accessed via the PROFIBUS converter option MCA 114.
Refer to 5 Parameter Mapping Lists for more information.
If a write request is attempted to a parameter selection
not supported, the frequency converter discards the
value and issues a positive reply. Only parameters and
functions described in this manual are supported.
NOTICE
The replacement frequency converter must match the
power size, or be bigger than the replaced VLT® 5000.
Make sure that the brake chopper matches the new
frequency converter.
Make sure that the new frequency converter meets the
local regulations concerning the machinery directive,
prefuses, and other appropriate regulations.
NOTICE
Observe local rules and regulations when replacing
frequency converter in existing installations.
1.3 Constraints
1.3.1 Software Versions
•
VLT® AutomationDrive FC 302 with firmware
version 5.5X or higher.
•
The MCA 114 Profibus Converter firmware is
based on a VLT® 5000 software version 3.9x and
PROFIBUS software version 4.5x.
With this PROFIBUS converter option the FC 302 reacts as
a VLT® 5000 on the PROFIBUS network. Changes to PLC
programming or configuration are normally not necessary.
The FC 302 identifies itself as a VLT® 5000 on the
PROFIBUS network, and a write command to e.g. Ramp Up
Time in VLT® 5000 is automatically linked to the
corresponding ramp up time parameter in VLT® AutomationDrive FC 302.
MG34N202 - Rev. 2013-10-15
3
1.3.2 Relations
VLT® 5000
Terminal
Function
This manual relates to the following hardware:
•
VLT® PROFIBUS Converter option, type no.
130B1246
•
MCB 101 General I/O option, type no. 130B1125
(uncoated), 130B1212 (coated)
•
MCB 107 External 24 Volt DC Supply, type no.
130B1108 (uncoated), 130B1208 (coated)
•
PROFIBUS adaptor Sub-D9 connector, type no.
130B1112. for enclosure types A1, A2 & A3
•
PROFIBUS adaptor Sub-D9 connector, type no.
176F1742 for enclosure types D & E
The VLT® PROFIBUS Converter MCA 114 supports
VLT® AutomationDrive FC 302 only.
•
•
There is no support for PROFIBUS FMS networks.
4
Function
Relay
01-03
Relay
68
RS-485-P
68
RS-485-P
69
RS-485-N
69
RS-485-N
61
GND RS-485
61
GND RS-485
12
24 V out
12
24 V out
13
24 V out
13
24 V out
50
10 V out
50
10 V out
Table 1.1 Terminal Mapping
* = General I/O option MCB 101
** = Switch “S201” must be OFF
*** = Switch “S202” must be ON
The FC 302 has fewer digital I/Os and analog
output signals than VLT® 5000. The General I/O
Option MCB 101 must be mounted in FC 302 to
map these signals and utilise all I/Os.
VLT® 5000
Terminal
Function
FC 302
Terminal
Function
16
Digital input
X30/2*
Digital input
17
Digital input
X3/3*
Digital input
18
Digital input
18
Digital input
19
Digital input
19
Digital input
27
Digital input
27
Digital input
29
Digital input
29
Digital input
32
Digital input
32
Digital input
33
Digital input
33
Digital input
20
GND Digital
input
20
GND Digital input
53
Analog input
voltage
53
Analog input voltage**
54
Analog input
voltage
X30/11***
Analog input voltage
60
Analog input
current
54
Analog input
current***
55
GND analog/
digital input
voltage
55
GND analog/digital
input voltage
42
Analog output 0/4-20
mA
X30/6*
Digital output
42
Terminal
01-03
1.3.3 Hardware
•
FC 302
130BT310.11
1 1
VLT® AutomationDrive FC 302 PROFIBUS Converter Operating Instructions
Introduction
Analog/digital
output
X30/7*
Pulse output
39
GND analog/
digital output
39
GND analog /digital
output
04-05
Relay
04-06
Relay
Illustration 1.1 Location of Switches S801, S201, and S202 (Left
to Right)
MG34N202 - Rev. 2013-10-15
VLT® AutomationDrive FC 302 PROFIBUS Converter Operating Instructions
Introduction
1 1
1.3.4 Performance
•
The dynamic performance on the motor shaft in
the closed loop operation compared with VLT®
5000 can be different in certain applications. If
necessary, adjust the PID controller manually.
•
The motor control algorithm of the VLT®
AutomationDrive FC 302 results in a better motor
performance compared to VLT® 5000.
NOTICE
Factory values:
After initialisation most parameters are set to match the
factory settings of the VLT® 5000 parameters. For more
information about the initialisation, see the VLT AutomationDrive FC 301/302 Programming Guide.
NOTICE
Linked Set-ups:
To synchronise set-up changes made with running
motor, ensure that FC 302 setups are linked. This is done
in 0-12 This Set-up Linked to.
1.4 Abbreviations
AOC
Application oriented control
CTW
Control word
EMC
Electromagnetic Compatibility
I/O
Input/Output
LED
Light Emitting Diode
LSB
Least Significant Bit
MAV
Main Actual Value (actual output)
MOC
Motor oriented control
MSB
Most Significant Bit
MRV
Main Reference Value (Setpoint)
N/A
Not applicable
PCD
Peripherals Communication Data (process data)
PCV
Parameter Characteristics Value (Parameter
channel)
PLC
Programmable Logic Controller
PNU
Parameter Number
PPO
Parameter Process Data Object
PU
Power Unit
REF
Reference (= MRV)
STW
Status Word
Table 1.2 Abbreviations
MG34N202 - Rev. 2013-10-15
5
VLT® AutomationDrive FC 302 PROFIBUS Converter Operating Instructions
Safety
2 Safety
2 2
WARNING
HIGH VOLTAGE
Frequency converters contain high voltage when
connected to AC mains input power. Failure to perform
installation, start-up, and maintenance by qualified
personnel could result in death or serious injury.
•
Installation, start-up, and maintenance must be
performed by qualified personnel only.
Safety regulations
1.
The frequency converter must be disconnected
from mains, if repair work is to be carried out.
Check that the mains supply has been disconnected and that the necessary time has passed
before removing motor and mains plugs, see
Discharge Time Table.
2.
3.
The [Off] key does not disconnect the equipment
from mains and is thus not to be used as a safety
switch.
Correct protective earthing of the equipment
must be established, the user must be protected
against supply voltage, and the motor must be
protected against overload in accordance with
applicable national and local regulations.
4.
The earth leakage currents are higher than 3.5
mA.
5.
Protection against motor overload is not included
in the factory setting. If this function is desired,
set 1-90 Motor Thermal Protection [4] ETR trip or
[3] ETR warning.
Warning against unintended start
1.
The motor can be brought to a stop with digital
commands, bus commands, references or a local
stop, while the frequency converter is connected
to mains. These stop funcyions are not sufficient
to prevent unintended starts.
2.
While parameters are being changed, the motor
may start. Consequently, [Off] must always be
activated.
3.
A motor that has been stopped may start if faults
occur in the electronics of the frequency
converter, or if a temporary overload or a fault in
the supply mains or the motor connection ceases.
WARNING
Touching the electrical parts may be fatal - even after
the equipment has been disconnected from mains.
Voltage [V]
4
15
200-240
0.25-3.7 kW
5.5-37 kW
380-480
0.25-7.5 kW
11-75 kW
525-600
0.75-7.5 kW
11-75 kW
525-690
6
11-75 kW
High voltage may be present even when the warning LED
indicator lights are off.
Table 2.1 Discharge Time
Also make sure that other voltage inputs have been
disconnected, such as external 24 V DC, load sharing
(linkage of DC intermediate circuit), as well as the motor
connection for kinetic back up.
The function is initialised at 1.16 x rated motor current and
rated motor frequency. For the North American market; the
ETR functions provide class 20 motor overload protection
in accordance with NEC.
6.
Do not remove the plugs for the motor and
mains supply while the frequency converter is
connected to mains. Check that the mains supply
has been disconnected and that the necessary
time has passed before removing motor and
mains plugs, see Discharge Time Table.
7.
Minimum waiting time (minutes)
The frequency converter has more voltage inputs
than L1, L2 and L3, when load sharing (linking of
DC intermediate circuit) and external 24 V DC
have been installed. Check that all voltage inputs
have been disconnected and that the necessary
time has passed before commencing repair work,
see Discharge Time Table.
MG34N202 - Rev. 2013-10-15
VLT® AutomationDrive FC 302 PROFIBUS Converter Operating Instructions
How to Install
3 How to Install
Terminate the bus line at both ends of each segment. A
mismatch of impedance may result in reflections on the
line resulting in corrupt data transmission.
3.2 How to Install Option in Frequency
Converter
3 3
130BT318.11
3.1 Connecting the Bus Line
The Profibus Option Card contains a suitable termination.
To activate the termination, turn on Switch 1 on the
Profibus converter option. By default, the switch is turned
off.
NOTICE
Notice that pin numbers are colour
coded on the Profibus connector.
Unlike the VLT® 5000, the FC 302 Profibus connectors are
colour-coded to avoid swapping the bus wires.
Illustration 3.2 Installing Fieldbus Option
Illustration 3.1 Connecting Bus Wires to VLT PROFIBUS
Converter MCA 114
Illustration 3.3 Cable Holders
Profibus B
62 = RxD/TxD
Positive, red cable
Profibus A
63 = RxD/TxD
Negative, green cable
Table 3.1 Correct Colour-Coding
1.
Remove the LCP from the FC 302.
2.
Remove the frame below the local control panel.
MG34N202 - Rev. 2013-10-15
7
3.
Push the option into place. Two positions are
possible, with cable terminal facing either up or
down. The cable up position is often most
suitable when several frequency converters are
installed side by side in a rack, as this position
permits shorter cable lengths.
4.
Push the fieldbus option adaptor frame for the FC
302 into place.
5.
Remount the LCP.
6.
Attach the cable.
7.
Fasten the cable using cable holders.
3.2.1 Mechanical Installation
To ease the replacement of VLT 5000 with VLT® AutomationDrive FC 302, there is a number of adapter plates available. The
adapter plates have the same footprints as VLT 5000 and have threaded holes for VLT® AutomationDrive FC 302. The
adapter plate prevents damage that can occur from drilling new threaded holes in the backboard of the enclosure. The
adapter plate also decreases the time required to exchange a broken frequency converter.
The following mechanical adapter plates are available:
Ordering
number
Style
Height [mm]
Width [mm]
Type
130B0183
Bookstyle, IP20
395
90
5001-5003 200-240 V
5001-5005 380-500 V
130B0184
Bookstyle, IP20
395
130
5004-5006 200-240 V
5006-5011 380-500 V
220
5001-5003 200-240 V
5001-5005 380-500 V
5004-5006 200-240 V
5006-5011 380-500 V
5001-5011 550-600 V
130B0185
Compact, IP20
395
130BA080.11
Table 3.2 Mechanical Installation for VLT® 5000
3.3 EMC Precautions
To achieve interference-free operation of the PROFIBUS:
•
Maintain high distance (min. 200 mm [8"])
between the PROFIBUS communication cable and
the motor and brake resistor cables to avoid
coupling of high frequency noise from one cable
to the other.
•
When crossing is unavoidable, ensure that the
PROFIBUS cable crosses motor and brake resistor
cables at an angle of 90 degrees.
Fieldbus cable
3 3
VLT® AutomationDrive FC 302 PROFIBUS Converter Operating Instructions
How to Install
Min.200mm
NOTICE
Observe relevant national and local regulations, for
example regarding protective earth connection.
90° crossing
Illustration 3.4 Correct EMC Installation
8
MG34N202 - Rev. 2013-10-15
VLT® AutomationDrive FC 302 PROFIBUS Converter Operating Instructions
How to Configure the System
4 How to Configure the System
Using the hardware switches, select an address range from
0 to 125 (factory setting 127) according to Illustration 4.1:
ON = 1, OFF = 0
4.1 Configure the PROFIBUS Network
130BA084.11
All PROFIBUS stations connected to the same bus network
must have a unique station address.
Before a VLT® 5000 can be replaced with an FC 302 with
MCA 114, only the station address needs to be configured
in the FC 302.
ON
The PROFIBUS address of the FC 302 can be selected via:
MCA 114
Option A
S600
130B1246
ON
Profibus
MS Converter
NS
OFF
NS
MS
• Hardware switches
• 9-18 Node Address
NOTICE
S300
ON
8 7 6 5 4 3 2 1 OFF
After installing PROFIBUS Converter MCA 114, check that
8-02 Control Word Source is set to [3] Option A.
ON
4.1.1 Setting the PROFIBUS Address using
the Hardware Switches
ON
Illustration 4.1 PROFIBUS Option A
CAUTION
Switch off the power supply before changing the
hardware switches.
CAUTION
The address change comes into effect at the next powerup, and can be read in 9-18 Node Address
VLT® 5000
FC 302
Switch
1
2
3
4
5
6
7
8
8
7
6
5
4
3
2
1
Address
+1
+2
+4
+8
+16
+32
+64
-
-
+64
+32
+16
+8
+4
+2
+1
1
1
0
0
0
0
0
0
-
-
0
0
0
0
0
0
1
35
1
1
0
0
0
1
0
-
-
0
1
0
0
0
1
1
82
0
1
0
0
1
0
1
-
-
1
0
1
0
0
1
0
Example:
Table 4.1 Hardware Switches
4.1.2 Setting the PROFIBUS Address via
9-18 Node Address
Setting the address via 9-18 Node Address or the PROFIBUS
SSA-command is possible, if the hardware switches are set
to 126 or 127 (factory switch setting). The new address
becomes active at the next power-up.
MG34N202 - Rev. 2013-10-15
9
4 4
4 4
VLT® AutomationDrive FC 302 PROFIBUS Converter Operating Instructions
How to Configure the System
4.1.3 Commissioning
4.2 LED Behaviour
After setting the station address from VLT® 5000 to VLT®
AutomationDrive FC 302, cycle power on the frequency
converter to activate the new address. The master/PLC
now recognizes the frequency converter as VLT® 5000. A
solid green NS LED on the MCA 114 option indicates that
communication between the master and the frequency
converter is established. If the NS LED flashes, the
master/PLC has not recognised the frequency converter.
The option has 2 bi-coloured LEDs:
LED label
Description
NS
Network Status
MS
Modul Status ( DP-V1 communication)
Table 4.2 Bi Coloured LEDs
For more information, refer to 6.1 Step-by-step Troubleshooting
State
Power On
Baud rate search
LED
Description
The option is defect. Contact
Danfoss
Red:
Solid red
Green:
Flashing green The option is OK.
Green:
Searching for the baud rate.
Check the connection to the
Flashing green
master if the option stays in this
state.
Green:
Long green
flash
Baud rate found - waiting for
parameters from the master.
Red:
Long red flash
Wrong parameters from the
master.
Green:
Short green
flash
Parameters from master OK –
waiting for configuration data.
Red:
Short red flash
Wrong Configuration data from
the master.
Green:
Solid green
Data Exchange between the
master and the FC 300 is active.
Red:
Flashing red
Wait Parameterising
Wait Configuration
Data Exchange
Clear State. Warning 34 is active
and a bus reaction in par. 8-04 is
executed.
Table 4.3 Net Status
LED
Description
No light
Off
No PROFIBUS DPV1 communication is active.
Green:
Short green flash
DP V1 communication from a Master Class 1
(PLC) is active.
Green:
Long green flash
DP V1 communication from a Master Class 2
(MCT 10, FDT) is active.
Green:
Solid green
DP V1 communication from a Master Class 1
and 2 is active.
Red:
Flashing red
Internal error.
Table 4.4 Module Status ( DP-V1 Communication)
NOTICE
The LEDs flash patterns of the MCA114 are not
compatible with the patterns of the VLT®5000 PROFIBUS
LEDs.
10
MG34N202 - Rev. 2013-10-15
How to Configure the System
VLT® AutomationDrive FC 302 PROFIBUS Converter Operating Instructions
4.3 Initialisation
To achieve the best performance, initialise the frequency
converter after the option is mounted. If the frequency
converter is delivered from factory with the option
installed, skip this step. The initialisation is done via
14-22 Operation Mode or a 3 finger reset. The parameters
of the FC 302 are set to factory values, and a number of
FC 302 parameters are set to values that match the VLT®
5000 initial values.
Factory copy via VLT® 5000 parameter 006 is supported
and initialises the FC 302 and also set it to the VLT® 5000
default settings.
The following parameters are set during the initialisation:
4 4
Parameter
Initialisation setting
0-02 Motor Speed Unit
[Hz]
1-52 Min Speed Normal Magnetising [Hz]
1.0 Hz
3-16 Reference Resource 2
[0] No function
4-12 Motor Speed Low Limit [Hz]
132.0 Hz
3-00 Reference Range
min – max
3-01 Reference/Feedback Unit
[1] %
3-11 Jog Speed [Hz]
10.0 Hz
4-30 Motor Feedback Loss Function
[0] Disabled
4-56 Warning Feedback Low
-4000000
4-57 Warning Feedback High
4000000
6-10 Terminal 53 Low Voltage
0.00 Volt
6-20 Terminal 54 Low Voltage
0.00 Volt
6-22 Terminal 54 Low Current
0.00 Volt
5-51 Term. 29 High Frequency
5000 Hz
5-56 Term. 33 High Frequency
25000 Hz
4-32 Motor Feedback Loss Timeout
1.00 s
14-21 Automatic Restart Time
5s
14-03 Overmodulation
[0] Off
7-33 Process PID Proportional Gain
0.01
8-54 Reversing Select
[0] Digital input
8-90 Bus Jog 1 Speed
300 RPM
8-91 Bus Jog 2 Speed
300 RPM
7-04 Speed PID Differentiation Time
OFF
2-10 Brake Function
[0] Off
2-17 Over-voltage Control
[0] Off
5-40 Function Relay
[22] Ready, no thermal Warning
5-41 On Delay, Relay
[23] Remote, ready, no TW
7-09 Speed PID Error Correction w/ Ramp
100000 (max)
14-11 Mains Voltage at Mains Fault
calculated value: VLT5000 level = FC 302 level
* 1,35 / sqrt(2)
MCB 101 option specific parameters
5-16 Terminal X30/2 Digital Input
[1] Reset
5-17 Terminal X30/3 Digital Input
[19] Freeze reference
PROFIBUS specific parameters
9-71 Profibus Save Data Values
[1] Store all setups
Table 4.5 Parameter Setup at Initialisation
MG34N202 - Rev. 2013-10-15
11
VLT® AutomationDrive FC 302 PROFIBUS Converter Operating Instructions
Parameter Mapping Lists
5 Parameter Mapping Lists
5.1 VLT® 5000 Parameter Group 0
VLT 5000 series
FC 302 series
Parameter
001 Language select
0-01 Language
Options
[0] English
[0] English
[1] Deutsch
[1] Deutsch
[2] French
[2] French
[3] Dansk
[3] Dansk
[4] Spanish
[4] Spanish
[5] Italian
[5] Italian
5 5
VLT 5000 series
FC 302 series
Parameter
006 Setup Copy
0-51 Set-up Copy
Options
[0] No Copy
[0] No Copy
[1]
[1]
[2]
[2]
[3]
[3]
[4]
[4]
Table 5.6 Conversion of Parameter 006
Parameter
Table 5.1 Conversion of Parameter 001
VLT 5000 series
FC 302 series
007 LCP Copy
Not converted
Table 5.7 Conversion of Parameter 007
VLT 5000 series
FC 302 series
Parameter
002 Local/remote control
Not converted
Options
[0] Remote
VLT 5000 series
FC 302 series
Parameter 008 Display scaling of motor
frequency
Not converted
[1] Local with External Stop
Table 5.8 Conversion of Parameter 008
[2] Local
Table 5.2 Conversion of Parameter 002
Parameter
VLT 5000 series
FC 302 series
003 Local reference
Not converted
Table 5.3 Conversion of Parameter 003
VLT 5000 series
FC 302 series
Parameter
004 Active Set-up
0-10 Active Set-up
Options
[0] Factory Setup
[0] Factory Setup
[1] Setup 1
[1] Setup 1
[2] Setup 2
[2] Setup 2
[3] Setup 3
[3] Setup 3
[4] Setup 4
[4] Setup 4
[5] Multi Setup
[9] Multi Setup
VLT 5000 series
FC 302 series
Parameter
number
009 Display line
0-23
Parameter
number
010 Display line
0-20
Parameter
number
011 Display line
0-21
Parameter
number
012 Display line
0-22
Options
[0] None
[0] None
[1] Reference %
[1602] Reference %
[2] Reference [Unit]
[1601] Reference
[Unit]
[3] Feedback [Unit]
[1652] Feedback
[Unit]
Table 5.4 Conversion of Parameter 004
[4] Frequency [Hz]
[1613] Frequency [Hz]
[5] Frequency x scale
[1609] Custom
readout
[6] Motor current [A]
[1614] Motor current
[A]
VLT 5000 series
FC 302 series
Parameter
005 Setup Copy
0-51 Set-up Copy
Options
[0] Factory Set-up
[0] Factory Set-up
[7] Torque [%]
[1622] Torque [%]
[1] Setup 1
[1] Setup 1
[8] Power [kW]
[1610] Power [kW]
[2] Setup 2
[2] Setup 2
[9] Power [HP]
[1611] Power [HP]
[3] Setup 3
[3] Setup 3
[4] Setup 4
[4] Setup 4
[10] Output energy
[kWh]
[1502] kWh counter
[kWh]
[5] Active Setup
[9] Active Setup
[11] Motor voltage [V]
[1612] Motor voltage
[V]
Table 5.5 Conversion of Parameter 005
12
Table 5.9 Conversion of Parameters 009 to 012
MG34N202 - Rev. 2013-10-15
Parameter Mapping Lists
VLT® AutomationDrive FC 302 PROFIBUS Converter Operating Instructions
VLT 5000 series
FC 302 series
Parameter
number
009
0-09 Performance Monitor
Parameter
Parameter
number
010
0-10 Active Set-up
Table 5.11 Conversion of Parameter 013
Parameter
number
011
0-11 Edit Set-up
Parameter
number
012
0-12 This Set-up Linked to
Options
[12] DC link voltage
[V]
[1630] DC link voltage [V]
[13] Thermal load,
motor [%]
[1618] Thermal load, motor
[%]
[14] Thermal load,
VLT® [%]
[1635] Inverter thermal [%]
[15] Running hours
[hours]
[1501] Running hours
[hours]
[16] Digital input
[1660] Digital input
[17] Analogue input [1662] Analogue input 53
53 [V]
[V]
[18] Analogue input [1664] Analogue input 54
54 [V]
[V]
[19] Analogue input [1662] Analogue input 53
60 [mA]
[mA]
[20] Pulse reference
[Hz]
[1651] Pulse reference [Hz]
[21] Ext. reference
[%]
[1650] Ext. reference [%]
[22] Status word
[hex]
[1603] Status word [hex]
[23] Brake effect/2
min [kW]
[1633] Brake effect/2 min
[kW]
VLT 5000 series
FC 302 series
013 Local Ctrl./config
Not converted
VLT 5000 series
FC 302 series
Parameter
014 Local Stop key
0-41 [Off] Key on LCP
Options
[0] Disable
[0] Disable
[1] Enable
[1] Enable
[2] Password
Table 5.12 Conversion of Parameter 014
VLT 5000 series
FC 302 series
Parameter
015 Local Jogging
Not converted
Options
[0] Disable
[1] Enable
Table 5.13 Conversion of Parameter 015
VLT 5000 series
FC 302 series
Parameter
016 Local Reversing
Not converted
Options
[0] Disable
[1] Enable
Table 5.14 Conversion of Parameter 016
VLT 5000 series
FC 302 series
Parameter
017 Local Stop key
0-43 [Reset] Key on LCP
Options
[0] Disable
[0] Disable
[1] Enable
[1] Enable
[2] Password
Table 5.15 Conversion of Parameter 017
[24] Brake effect/sec [1632] Brake effect/sec [kW]
[kW]
VLT 5000 series
FC 302 series
[25] Heat sink temp. [1634] Heat sink temp.
Parameter 018 Lock for data
change
0-61 Access to Main Menu
w/o Password
[26] Alarm word
[hex]
Options
[0] Not locked
[0] Full access
[1] Lock
[1] LCP: Read only
[27] Control word
[hex]
5 5
[1600] Control word [hex]
[28] Warning word 1
[hex]
Table 5.16 Conversion of Parameter 018
VLT 5000 series
[29] Warning word 2
[hex]
FC 302 series
Parameter 019 Power-Up Mode
0-04 Operating State at
Power-up (Hand)
Options
[0] Auto Restart, use
saved ref.
[0] Resume
[1] Forced stop, use saved
ref.
[30] Com. Option
warning [hex]
[953] Com. Option warning
[hex]
[31] RPM [min]
[1617] Speed RPM [min]
[1] Forced stop, use
saved ref.
[32] RPM x scaling
[min]
[1609] Custom readout
[2] Forced stop, set ref [2] Forced stop, set ref = 0
= 0.
[33] LCP display text Not possible
Table 5.17 Conversion of Parameter 019
Table 5.10 Conversion of Parameters 009 to 012
MG34N202 - Rev. 2013-10-15
13
Parameter Mapping Lists
VLT® AutomationDrive FC 302 PROFIBUS Converter Operating Instructions
VLT 5000 series
FC 302 series
Parameter
027 Warning readout line
Not converted
Options
[0] Warning in line 1/2
5.2 VLT® 5000 Parameter Group 1
[1] Warning in line 3/4
Table 5.18 Conversion of Parameter 027
VLT 5000 series
FC 302 series
Parameter 100 Configuration
0-02
1-01 Motor Control Principle
Options
[0] Speed control,
open loop
Par. 1-00 = [0] Speed open loop
[1] Speed control,
closed loop
Par. 0-02 = [0] RPM
Par. 1-00 = [1] Speed closed loop
[3] Process
control, closed
loop
Par. 1-00 = [3] Process
5 5
Par. 1-01 = [1] VVCplus
Par. 1-01 = [1] VVCplus
[4] Torque control, Par. 1-00 = [4] Torque open loop
open loop
Par.1-01 = [1] VVCplus
[5] Torque control, Par. 1-00 = [2] Torque close loop
speed feedback
Par. 1-01 = [3] Flux with motor fb
Par. 5-71 = [1] Counter clockwise
Table 5.19 Conversion of Parameter 100
VLT 5000 series
FC 302 series
Parameter 101 Torque characteristic
1-03 Torque Characteristics
1-04 Overload Mode
14-40 VT Level
Options
[1] High constant
torque
Par. 1-03 = [0] Constant torque
Par. 1-04 Over load = [0] High
[2] High variable
torque low
Par. 1-03 = [1] Variable torque
Par. 14-40 VT level = 45%
Par. 1-04 Over load = [0] High
[3] High variable
torque medium
Par. 1-03 = [1] Variable torque
Par. 14-40 VT level = 66%
Par. 1-04 Over load = [0] High
[4] High variable
torque high
Par. 1-03 = [1] Variable torque
Par. 14-40 VT level = 85%
Par. 1-04 Over load = [0] High
[5] High special
motor characteristic
Par. 1-01 = [0] U/f
Par. 1-04 Over load = [0] High
[6] High variable
torque with low
starting torque
Par. 1-03 = [1] Variable torque
Par. 14-40 VT level = 45%
Par. 1-04 Over load = [0] High
Table 5.20 Conversion of Parameter 101
14
MG34N202 - Rev. 2013-10-15
VLT® AutomationDrive FC 302 PROFIBUS Converter Operating Instructions
Parameter Mapping Lists
VLT 5000 series
FC 302 series
Parameter 101 Torque charac- 1-03 Torque Characteristics
teristic
1-04 Overload Mode
14-40 VT Level
Parameter
105 Motor Current
1-24 Motor Current
Range
Power Unit dependable
Power Unit dependable
Options
Table 5.25 Conversion of Parameter 105
VLT 5000 series
FC 302 series
[7] High variable
torque with
medium starting
torque
Par. 1-03 = [1] Variable torque
Par. 14-40 VT level = 66%
Par. 1-04 Over load = [0] High
[8] High variable
torque with high
starting torque
Par. 1-03 = [1] Variable torque
Par. 14-40 VT level = 85%
Par. 1-04 Over load = [0] High
[11] Normal
constant torque
Par. 1-03 = [0] Constant torque
Par. 1-04 Over load = [1] Normal
VLT 5000 series
FC 302 series
Parameter 106 Rated motor speed 1-25 Motor Nominal Speed
[12] Normal
Par. 1-03 = [1] Variable torque
variable torque low Par. 14-40 VT level = 45%
Par. 1-04 Over load = [1] Normal
[13] Normal
variable torque
medium
Par. 1-03 = [1] Variable torque
Par. 14-40 VT level = 66%
Par. 1-04 Over load = [1] Normal
[14] Normal
variable torque
high
Par. 1-03 = [1] Variable torque
Par. 14-40 VT level = 85%
Par. 1-04 Over load = [1] Normal
[15] Normal special Par. 1-01 = [0] U/f
motor characteristic Par. 1-04 Over load = [1] Normal
[16] Normal
variable torque
with low constant
starting torque
Par. 1-03 = [1] Variable torque
Par. 14-40 VT level = 45%
Par. 1-04 Over load = [1] Normal
[17] Normal
variable torque
with medium
constant starting
torque
Par. 1-03 = [1] Variable torque
Par. 14-40 VT level = 66%
Par. 1-04 Over load = [1] Normal
[18] Normal
variable torque
with high constant
starting torque
Par. 1-03 = [1] Variable torque
Par. 14-40 VT level = 85%
Par. 1-04 Over load = [1] Normal
Range
100 – 60000
10 – 60000
Table 5.26 Conversion of Parameter 106
VLT 5000 series
5 5
FC 302 series
Parameter 107 Automatic motor
adaptation
1-29 Automatic Motor
Adaptation (AMA)
Options
[0] Adaptation off
[0] Off
[1] Adaptation on, Rs
and Xs
[1] Enable complete AMA
[2] Adaptation on, RS
[2] Enable reduce AMA
Table 5.27 Conversion of Parameter 107
VLT 5000 series
FC 302 series
Parameter 108 Stator resistor
1-30 Stator Resistance (Rs)
Range
0.0140 – 140.0000
Power Unit dependable
Table 5.28 Conversion of Parameter 108
VLT 5000 series
FC 302 series
Parameter 109 Stator reactance
1-35 Main Reactance (Xh)
Range
1.0000 – 10000.0000
Power Unit dependable
Table 5.29 Conversion of Parameter 109
Range
FC 302 series
0 – 300%
0 – 300%
Table 5.30 Conversion of Parameter 110
Table 5.21 Conversion of Parameter 101
VLT 5000 series
VLT 5000 series
Parameter 110 Motor magnetizing at 1-50 Motor Magneti0 RPM
sation at Zero Speed
VLT 5000 series
FC 302 series
Parameter
102 Motor Power
1-20 Motor Power [kW]
Range
0.18 – 600 kW
0.09 – 3000 kW
Table 5.22 Conversion of Parameter 102
FC 302 series
Parameter
111 Min. frequency 1-52 Min Speed
normal magnetizing Normal Magnetising
[Hz]
Range
0.1 – 10.0 Hz
0.3 – 10.0 Hz
Table 5.31 Conversion of Parameter 111
VLT 5000 series
FC 302 series
Parameter
103 Motor Voltage
1-22 Motor Voltage
Range
200 – 600 Volt
50 – 1000 V
VLT 5000 series
FC 302 series
Parameter 113 Load compensation at 1-60 Low Speed Load
low speed
Compensation
Table 5.23 Conversion of Parameter 103
Range
VLT 5000 series
FC 302 series
Parameter
104 Motor frequency
1-23 Motor Frequency
Range
20 -1000 Hz
20 -1000 Hz
0 – 300%
0 – 300%
Table 5.32 Conversion of Parameter 113
Table 5.24 Conversion of Parameter 104
MG34N202 - Rev. 2013-10-15
15
5 5
VLT® AutomationDrive FC 302 PROFIBUS Converter Operating Instructions
Parameter Mapping Lists
VLT 5000 series
VLT 5000 series
FC 302 series
FC 302 series
Parameter 121 Start function
1-72 Start Function
Options
[0] DC hold in start delay
time
[0] DC hold/delay time
Table 5.33 Conversion of Parameter 114
[1] DC brake in start delay
time
[1] DC Brake/delay
time
VLT 5000 series
FC 302 series
[2] Coast/delay time
Parameter
115 Slip Compensation
1-62 Slip Compensation
[2] Coasting in start delay
time
Range
-500 - 500%
-500 - 500%
[3] Start frequency/voltage
clockwise
[3] Start speed cw
[4] Start frequency/voltage
in reference direction
[4] Horizontal
operation
[5] VVCplus clockwise
[5] VVCplus/Flux
Parameter 114 Load compensation at 1-61 High Speed Load
high speed
Compensation
Range
0 – 300%
0 – 300%
Table 5.34 Conversion of Parameter 115
VLT 5000 series
FC 302 series
Parameter 116 Slip Compensation
Time constant
1-63 Slip Compensation
Time Constant
Range
0.05 – 5.00 s
0.05 – 1.00 s
Table 5.35 Conversion of Parameter 116
VLT 5000 series
FC 302 series
clockwise
Table 5.40 Conversion of Parameter 121
VLT 5000 series
FC 302 series
Parameter
122 Function at stop
1-80 Function at Stop
Options
[0] Coasting
[0] Coast
[1] DC hold
[1] DC hold
Parameter 117 Resonance dampening 1-64 Resonance Damping
Range
0 - 500%
0 - 500%
Table 5.36 Conversion of Parameter 117
VLT 5000 series
FC 302 series
1-65 Resonance Damping
Time Constant
Range
5 – 50 ms
VLT 5000 series
FC 302 series
119 High starting torque
Not converted
FC 302 series
1-82 Min Speed for
Function at Stop [Hz]
Range
0.0 – 20.0 Hz
0.0 – 10.0 Hz
VLT 5000 series
FC 302 series
Parameter 124 DC holding current 2-00 DC Hold Current
Table 5.38 Conversion of Parameters 119
Range
VLT 5000 series
FC 302 series
Parameter
120 Start delay
1-71 Start Delay
Option
0.0 – 10.0 s
0.0 – 10.0 s
Table 5.39 Conversion of Parameter 120
VLT 5000 series
Parameter 123 Min frequency for
function at stop
Table 5.42 Conversion of Parameter 123
Table 5.37 Conversion of Parameter 118
Parameter
[2] Motor check
[3] Pre-magnetizing
Table 5.41 Conversion of Parameter 122
Parameter 118 Resonance
dampening time
constant
5 – 50 ms
[2] Motor check
[3] Pre-magnetizing
0 - 100%
0 - 160% (motor depending)
Table 5.43 Conversion of Parameter 124
VLT 5000 series
FC 302 series
Parameter 125 DC braking current
2-01 DC Brake Current
Range
0 – 160% P.U depending
0 - 100%
Table 5.44 Conversion of Parameter 125
VLT 5000 series
FC 302 series
Parameter
126 DC braking time
2-02 DC Braking Time
Range
0.0 – 60.0 s
0.0 – 60.0 s
Table 5.45 Conversion of Parameter 126
16
MG34N202 - Rev. 2013-10-15
VLT® AutomationDrive FC 302 PROFIBUS Converter Operating Instructions
Parameter Mapping Lists
VLT 5000 series
FC 302 series
Parameter 127 DC brake cut-in
frequency
2-04 DC Brake Cut In
Speed [Hz]
Range
0.0 (Off) – fmax (par. 414)
0.0 (Off) – fmax (par. 202)
Table 5.46 Conversion of Parameter 127
VLT 5000 series
FC 302 series
Parameter 128 Motor thermal
protection
1-90 Motor Thermal
Protection
Options
[0] No protection
[0] No protection
[1] Thermistor warning
[1] Thermistor warning
[2] Thermistor trip
[2] Thermistor trip
[3] ETR warning 1
[3] ETR warning 1
[4] ETR trip 1
[4] ETR trip 1
[5] ETR warning 2
[5] ETR warning 2
[6] ETR trip 2
[6] ETR trip 2
[7] ETR warning 3
[7] ETR warning 3
[8] ETR trip 3
[8] ETR trip 3
[9] ETR warning 4
[9] ETR warning 4
[10] ETR trip 4
[10] ETR trip 4
5 5
Table 5.47 Conversion of Parameter 128
VLT 5000 series
FC 302 series
Parameter
129 External motor fan
1-91 Motor External Fan
Options
[0] No
[0] No
[1] Yes
[1] Yes
Table 5.48 Conversion of Parameter 129
VLT 5000 series
FC 302 series
Parameter 130 Start frequency
1-75 Start Speed [Hz]
Range
0.0 – 500 Hz P.U depending
0.0 – 10.0 Hz
Table 5.49 Conversion of Parameter 130
Parameter
VLT 5000 series
FC 302 series
131 Initial voltage
Not converted
Table 5.50 Conversion of Parameter 131
Parameter
VLT 5000 series
FC 302 series
145 Minimum DC brake time
Not converted
Table 5.51 Conversion of Parameter 132
MG34N202 - Rev. 2013-10-15
17
VLT® AutomationDrive FC 302 PROFIBUS Converter Operating Instructions
Parameter Mapping Lists
5.3 VLT® 5000 Parameter Group 2
VLT 5000 series
FC 302 series
Parameter 200 Output Frequency Range/
Direction
Options
4-10 Motor Speed
Direction
[0] Only clockwise, 0 – 132 Hz
[0] Clockwise
[1] Both directions, 0 – 132 Hz
[2] Both directions
[2] Only clockwise, 0 – 1000 Hz
[0] Clockwise
VLT 5000 series
3-03 Maximum Reference
6-15 Terminal 53 High Ref./Feedb.
Value
6-25 Terminal 54 High Ref./Feedb.
Value
5-53 Term. 29 High Ref./Feedb.
Value
5-58 Term. 33 High Ref./Feedb.
Value
Range
Par. 3-02 Refmin – 100,000.000
[3] Both directions, 0 – 1000 Hz [2] Both directions
5 5
[4] Only counter clockwise, 0 –
132 Hz
[1] Counter
clockwise
[5] Only counter clockwise, 0 –
1000 Hz
[1] Counter
clockwise
Table 5.57 Conversion of Parameter 205
FC 302 series
VLT 5000 series
Parameter 201 Output frequency
low limit
4-12 Motor Speed Low
Limit [Hz]
Range
0 – par. 414 Fmax [Hz]
0.0 – par. 202 Fmax
Par. 204 Refmin –
100,000.000
Table 5.52 Conversion of Parameter 200
VLT 5000 series
3-40 Ramp 1 Type
3-50 Ramp 2 Type
3-82 Quick Stop Ramp Type
Options
Par. 3-40 = [0] Linear
Par. 3-50 = [0] Linear
Par. 3-82 = [0] Linear
[0] Linear
4-14 Motor Speed High
Limit [Hz]
4-19 Max Output Frequency
Range
0 – 1000 Hz
0.0 – 132/1000 Hz
[1] Sine shape (S1) Par. 3-40 = [2] S-ramp Const Time
Par. 3-45 = 1%
Par. 3-46 = 25%
Par. 3-47 = 1%
Par. 3-48 = 25%
Par. 3-50 = [2] S-ramp Const Time
Par. 3-55 = 1%
Par. 3-56 = 25%
Par. 3-57 = 1%
Par. 3-58 = 25%
Par. 3-82 = [2] S-ramp Const Time
Par. 3-83 = 1%
Par. 3-84 = 25%
FC 302 series
Parameter 202 Output frequency
high limit
Table 5.54 Conversion of Parameter 202
VLT 5000 series
FC 302 series
Parameter 203 Reference/feedback area
3-00 Reference Range
Options
[0] Min – Max
[0] Min – Max
[1] - Max - +Max
[1] - Max - +Max
[2] Sin2 Shape
(S2)
Table 5.55 Conversion of Parameter 203
VLT 5000 series
FC 302 series
Parameter
204 Minimum
reference
3-02 Minimum
Reference
Range
-100,000.000 – par.
205 Refmax
-100,000.000 – par.
3-03 Refmax
FC 302 series
Parameter 206 Ramp Type
Table 5.53 Conversion of Parameter 201
VLT 5000 series
FC 302 series
Parameter 205 Maximum
reference
Table 5.56 Conversion of Parameter 204
Par. 3-40 = [2] S-ramp Const Time
Par. 3-45 = 25%
Par. 3-46 = 25%
Par. 3-47 = 25%
Par. 3-48 = 25%
Par. 3-50 = [2] S-ramp Const Time
Par. 3-55 = 25%
Par. 3-56 = 25%
Par. 3-57 = 25%
Par. 3-58 = 25%
Par. 3-82 = [2] S-ramp Const Time
Par. 3-83 = 25%
Par. 3-84 = 25%
Table 5.58 Conversion of Parameter 206
18
MG34N202 - Rev. 2013-10-15
VLT® AutomationDrive FC 302 PROFIBUS Converter Operating Instructions
Parameter Mapping Lists
VLT
5000
series
FC 302 series
Parameter 206
Ramp
Type
3-40 Ramp 1 Type3-50 Ramp 2
Type3-82 Quick Stop Ramp Type
Options
[0]
Linear
[0] Linear. Write to p.340, 350 and 382
[3] Sin3
Shape
(S3)
Par. 3-40 = [2] S-ramp Const Time
Par. 3-45 = 50%
Par. 3-46 = 50%
Par. 3-47 = 50%
Par. 3-48 = 50%
Par. 3-50 = [2] S-ramp Const Time
Par. 3-55 = 50%
Par. 3-56 = 50%
Par. 3-57 = 50%
Par. 3-58 = 50%
Par. 3-82 = [2] S-ramp Const Time
Par. 3-83 = 50%
Par. 3-84 = 50%
[4] Sin2
filter
Par. 3-40 = [2] S-ramp Const Time
Par. 3-45 = 25%
Par. 3-46 = 25%
Par. 3-47 = 25%
Par. 3-48 = 25%
Par. 3-50 = [2] S-ramp Const Time
Par. 3-55 = 25%
Par. 3-56 = 25%
Par. 3-57 = 25%
Par. 3-48 = 25%
Par. 3-82 = [2] S-ramp Const Time
Par. 3-83 = 25%
Par. 3-84 = 25%
Table 5.59 Conversion of Parameter 206
VLT 5000 series
FC 302 series
Parameter 207 Ramp up Time 1
3-41 Ramp 1 Ramp Up Time
Range
0.01 – 3600.00 s
0.05 – 3600.00 s
Table 5.60 Conversion of Parameter 207
VLT 5000 series
FC 302 series
Parameter 208 Ramp down Time 1 3-42 Ramp 1 Ramp Down
Time
Range
0.05 – 3600.00 s
FC 302 series
Parameter 209 Ramp up Time 2
3-51 Ramp 2 Ramp Up Time
Range
0.01 – 3600.00 s
0.05 – 3600.00 s
FC 302 series
211 Jog ramp time
3-80 Jog Ramp Time
Range
0.05 – 3600.00 s
0.01 – 3600.00 s
Table 5.64 Conversion of Parameter 211
VLT 5000 series
3-81 Quick Stop Ramp
Time
Range
0.01 – 3600.00 s
0.05 – 3600.00 s
Table 5.65 Conversion of Parameter 212
VLT 5000 series
FC 302 series
Parameter
213 Jog Frequency
3-11 Jog Speed [Hz]
Range
0.0 – par. 202
0.0 – par. 4-14
VLT 5000 series
FC 302 series
Parameter
214 Reference function
3-04 Reference Function
Options
[0] Sum
[0] Sum
[1] Relative
See comment below*
[2] External/Preset
[2] External/Preset
Table 5.67 Conversion of Parameter 214
*= Relative reference is added to the MRV from PROFIBUS.
VLT 5000 series
FC 302 series
Parameter
215 Preset Reference 1
3-10 Preset Reference
Range
-100.00 – 100.00%
-100.00 – 100.00%
Table 5.68 Conversion of Parameter 215
VLT 5000 series
FC 302 series
Parameter
216 Preset Reference 2
3-10 Preset Reference
Range
-100.00 – 100.00%
-100.00 – 100.00%
Table 5.69 Conversion of Parameter 216
VLT 5000 series
FC 302 series
Parameter
217 Preset Reference 3
3-10 Preset Reference
Range
-100.00 – 100.00%
-100.00 – 100.00%
Table 5.70 Conversion of Parameter 217
VLT 5000 series
FC 302 series
Parameter
218 Preset Reference 4
3-10 Preset Reference
Range
-100,00 - 100,00%
-100,00 - 100,00%
Table 5.71 Conversion of Parameter 218
FC 302 series
Parameter 219 Catch up/slow
down value
3-12 Catch up/slow Down
Value
Parameter 210 Ramp down Time 2 3-52 Ramp 2 Ramp Down
Time
Range
0.00 – 100%
Range
Table 5.72 Conversion of Parameter 219
VLT 5000 series
0.05 – 3600.00 s
FC 302 series
0.01 – 3600.00 s
5 5
Table 5.66 Conversion of Parameter 213
VLT 5000 series
Table 5.62 Conversion of Parameter 209
FC 302 series
Parameter 212 Quick stop ramp
time
0.01 – 3600.00 s
Table 5.61 Conversion of Parameter 208
VLT 5000 series
VLT 5000 series
Parameter
0.00 – 100%
Table 5.63 Conversion of Parameter 210
MG34N202 - Rev. 2013-10-15
19
5 5
VLT® AutomationDrive FC 302 PROFIBUS Converter Operating Instructions
Parameter Mapping Lists
VLT 5000 series
VLT 5000 series
FC 302 series
Parameter 221 Torque limit for
motor mode
4-16 Torque Limit Motor
Mode
Parameter 229 Frequency bypass,
bandwidth
Range
0.0 – Max. torque %
Range
0.0 – Max. torque %
Stored in EEprom only
0 - 100%
Table 5.81 Conversion of Parameter 229
Table 5.73 Conversion of Parameter 221
VLT 5000 series
FC 302 series
VLT 5000 series
FC 302 series
FC 302 series
Parameter 222 Torque limit for
generating mode
4-17 Torque Limit
Generator Mode
Parameter 230 Frequency Bypass
1
4-61 Bypass Speed From [Hz]
4-63 Bypass Speed To [Hz]
Range
0.0 – Max. torque %
Range
0 – par. 4-14
0.0 – Max. torque %
Table 5.74 Conversion of Parameter 222
VLT 5000 series
0 – par. 200
Table 5.82 Conversion of Parameter 230
FC 302 series
VLT 5000 series
FC 302 series
Parameter 223 Warning: Current
Low
4-50 Warning Current Low
2-20 Release Brake Current
Parameter 2-31 Frequency Bypass 4-61 Bypass Speed From [Hz]
2
4-63 Bypass Speed To [Hz]
Range
0.00 – par. 4-51
Range
0.0 – par. 2-24 Current
High
0 – par. 200
0 – par. 4-14
Table 5.83 Conversion of Parameter 231
Table 5.75 Conversion of Parameter 223
VLT 5000 series
VLT 5000 series
FC 302 series
Parameter 224 Warning: Current
High
4-51 Warning Current
High
Range
Power Unit dependable
Power Unit dependable
FC 302 series
Parameter 232 Frequency Bypass
3
4-61 Bypass Speed From [Hz]
4-63 Bypass Speed To [Hz]
Range
0 – par. 4-14
0 – par. 200
Table 5.84 Conversion of Parameter 232
Table 5.76 Conversion of Parameter 224
VLT 5000 series
VLT 5000 series
FC 302 series
Parameter 225 Warning Low
Frequency
4-52 Warning Speed Low
2-22 Activate Brake Speed
[Hz]
Range
0,0 – Par. 4-53
0,0 – par. 226
FC 302 series
Parameter 233 Frequency Bypass
4
4-61 Bypass Speed From [Hz]
4-63 Bypass Speed To [Hz]
Range
0 – par. 4-14
0 – par. 200
Table 5.85 Conversion of Parameter 233
Table 5.77 Conversion of Parameter 225
VLT 5000 series
FC 302 series
FC 302 series
Parameter 234 Motor phase
monitor
4-58 Missing Motor Phase
Function
Parameter 226 Warning High
Frequency
4-53 Warning Speed High
Range
[0] Enable
[2] Trip 1000 ms
Range
Par. 4-52 – par. 4-13
[1] Disable
[0] Disable
VLT 5000 series
par. 2-25 – par. 202
Table 5.86 Conversion of Parameter 234
Table 5.78 Conversion of Parameter 226
VLT 5000 series
FC 302 series
Parameter 227 Warning Low
Feedback
4-56 Warning Feedback
Low
Range
-999,999.999 – par. 4-57
-100,000.000 – par. 228
Table 5.79 Conversion of Parameter 227
VLT 5000 series
FC 302 series
Parameter 228 Warning High
Feedback
4-57 Warning Feedback
High
Range
Par. 4-56 – 999,999.999
par. 227 – 100,000.000
Table 5.80 Conversion of Parameter 228
20
MG34N202 - Rev. 2013-10-15
VLT® AutomationDrive FC 302 PROFIBUS Converter Operating Instructions
Parameter Mapping Lists
VLT 5000 series
5.4 VLT® 5000 Parameter Group 3
VLT 5000 series
Parameter 300 Terminal 16, input
Options
FC 302 series
[0] No function
[1] Reset
[1] Reset
[2] Stop inverse
[6] Stop inverse
[3] Only start clockwise,
on
[12] Enable start forward
[4] Jog
[14] Jog
[5] Preset reference, on
[15] Preset reference, on
[6] Preset reference, lsb
[16] Preset reference bit
0
Options
[0] No function
[0] No operation
[1] Start
[8] Start
[2] Latched start
[9] Latched start
[3] Only start clockwise,
on
[12] Enable start forward
Table 5.89 Conversion of Parameter 302
VLT 5000 series
[7] Freeze reference
[17] Freeze reference
[8] Freeze output
[20] Freeze output
[9] Speed up
[21] Speed up
[10] Choice of setup, lsb
[23] Setup select bit 0
[11] Catch-up
[28] Catch-up
[12] Ramp 2
[34] Ramp bit 0
Not supported
Comments FC 300 does not have a digital input 16, so this is
linked to 5-16 Terminal X30/2 Digital Input
Parameter 303 Terminal 19, input
5-11 Terminal 19 Digital
Input
Options
[0] No function
[0] No operation
[1] Reversing
[10] Reversing
[2] Start reversing
[11] Start reversing
[3] Only start
anticlockwise, on
[13] Enable start reverse
VLT 5000 series
5 5
FC 302 series
Parameter 304 Terminal 27, input
5-12 Terminal 27 Digital
Input
Options
[0] Coasting stop,
inverse
[2] Coast inverse
[1] Reset and Coasting
stop, inv.
[3] Coast and reset inv
Table 5.87 Conversion of Parameter 300
VLT 5000 series
FC 302 series
Table 5.90 Conversion of Parameter 303
[13] Mains failure inverted Not supported
[29] Data change lock
5-10 Terminal 18 Digital
Input
5-16 Terminal X30/2
Digital Input
[0] No function
FC 302 series
Parameter 302 Terminal 18, input
FC 302 series
[2] Quick-stop, inverse
[4] Quick-stop, inverse
Parameter 301 Terminal 17, input
5-17 Terminal X30/3
Digital Input
[3] DC-braking, inverse
[5] DC-brake inverse
[4] Stop inverse
[6] Stop inverse
Options
[0] No function
[0] No operation
[1] Reset
[1] Reset
[2] Stop inverse
[6] Stop inverse
Table 5.91 Conversion of Parameter 304
[3] Only start anticlockwise, [13] Enable start reverse
on
[4] Jog
[14] Jog
[5] Preset reference, on
[15] Preset reference,
on
[6] Preset reference, msb
[17] Preset reference bit
1
[7] Freeze reference
[19] Freeze reference
[8] Freeze output
[20] Freeze output
[9] Speed down
[22] Speed down
[10] Choice of setup, msb
[24] Setup select bit 1
[11] Slow down
[29] Slow down
[12] Ramp 2
[34] Ramp bit 0
[13] Mains failure inverted
Not supported
[23] Pulse reference
[32] Pulse input
[24] Safety interlock
Not supported
[29] Data change lock
Not supported
Comments FC 300 does not have a digital input 17, so this is
linked to 5-16 Terminal X30/2 Digital Input
Table 5.88 Conversion of Parameter 301
MG34N202 - Rev. 2013-10-15
21
VLT® AutomationDrive FC 302 PROFIBUS Converter Operating Instructions
Parameter Mapping Lists
VLT 5000 series
FC 302 series
VLT 5000 series
Parameter 305 Terminal 29, input
5-13 Terminal 29 Digital
Input
Options
[0] No function
[0] No operation
[1] Reset
[1] Reset
[2] Stop inverse
[6] Stop inverse
[3] Only start clockwise,
on
[12] Enable start forward
[4] Only start
anticlockwise, on
[5] Jog
5 5
5-15 Terminal 33 Digital
Input
7-00 Speed PID Feedback
Source
Options
[0] No function
[0] No operation
[1] Reset
[1] Reset
[2] Stop inverse
[6] Stop inverse
[13] Enable start reverse
[3] Only start
anticlockwise, on
[13] Enable start reverse
[14] Jog
[4] Jog
[14] Jog
[6] Preset reference, on
[15] Preset reference, on
[5] Preset reference, on
[15] Preset reference, on
[7] Preset reference, lsb
[16] Preset reference bit 0
[6] Preset reference, msb [17] Preset reference bit 1
[8] Preset reference, msb
[17] Preset reference bit 1
[7] Freeze reference
[9] Freeze reference
[19] Freeze reference
[8] Freeze output
[20] Freeze output
[10] Freeze output
[20] Freeze output
[9] Speed down
[22] Speed down
[11] Speed up
[21] Speed up
[24] Setup select bit 1
[12] Speed down
[22] Speed down
[10] Choice of Setup,
msb
[13] Choice of Setup, lsb
[23] Setup select bit 0
[11] Choice of Setup,
msb / Speed down
Not supported
[14] Choice of Setup, msb [24] Setup select bit 1
[15] Catch up
[28] Catch up
[12] Slow down
[29] Slow down
[16] Slow down
[29] Slow down
[13] Ramp 2
[34] Ramp bit 0
[34] Ramp bit 0
Not supported
[18] Mains failure inverted Not supported
[14] Mains failure
inverted
[28] Pulse reference
[32] Pulse input
[24] Pulse feedback
[29] Data change lock
Not supported
[32] Pulse input,
Parameter 700 = [9]
Frequency input 33
[25] Encoder input 2B
[0] No operation
Parameter 700 = [1] 24 V
encoder
[29] Data change lock
Not supported
[17] Ramp 2
Table 5.92 Conversion of Parameter 305
VLT 5000 series
FC 302 series
Parameter 306 Terminal 32, input
5-14 Terminal 32 Digital
Input
Options
[0] No function
[0] No operation
[1] Reset
[1] Reset
[2] Stop inverse
[6] Stop inverse
[3] Only start clockwise,
on
[12] Enable start forward
[4] Jog
[14] Jog
[5] Preset reference, on
[15] Preset reference, on
[6] Preset reference, lsb
[16] Preset reference bit 0
[7] Freeze reference
[19] Freeze reference
[8] Freeze output
[20] Freeze output
[9] Speed up
[21] Speed up
[11] Choice of Setup,
msb / Speed up
Not supported
[12] Catch up
[28] Catch up
[13] Ramp 2
[34] Ramp bit 0
[14] Mains failure
inverted
Not supported
[24] Encoder input 2A
[0] No operation
[29] Data change lock
Not supported
[19] Freeze reference
Table 5.94 Conversion of Parameter 307
[10] Choice of Setup, lsb [23] Setup select bit 0
Table 5.93 Conversion of Parameter 306
22
FC 302 series
Parameter 307 Terminal 33, input
MG34N202 - Rev. 2013-10-15
VLT® AutomationDrive FC 302 PROFIBUS Converter Operating Instructions
Parameter Mapping Lists
VLT 5000
series
FC 302 series
VLT 5000 series
FC 302 series
Parameter
311 Terminal 54,
Analogue Input
Voltage
3-16 Reference
Resource 2
7-00 Speed PID
Feedback Source
4-20 Torque Limit
Factor Source
1-93 Thermistor
Resource
4-21 Speed Limit
Factor Source
Options
[0] No Operation
Par. 3-16 Reference
resource 2 set to [0]
No function
Parameter 308 Terminal
53, Analogue
Input Voltage
3-15 Reference Resource 1
7-00 Speed PID Feedback Source
1-93 Thermistor Resource
4-20 Torque Limit Factor Source
Options
[0] No
Operation
Par. 3-15 Reference resource 1 set to
[0] No function
[1] Reference
Par. 3-15 Reference resource 1 set to
[1] Analog input 53
[2] Feedback
signal
Par. 3-15 Reference resource 1 set to
[1] Analog input 53
Par. 7-00 Speed PID Feedback
Source set to [6] Analog input 53
[3] Torque
limit
Par. 3-15 Reference resource 1 set to
[1] Analog input 53
Par. 4-20 Torque Limit Factor Source
set to [2] Analog in 53
[1] Reference
Par. 3-16 Reference
resource 1 set to [2]
Analog input 53
[2] Torque limit
[4] Thermistor
Par. 3-15 Reference resource 1 set to
[0] No function
Par. 1-93 Thermistor Ressource set to
[1] Analog input 53
Par. 4-20 Torque
Limit Factor Source
set to [6] Analog in
54
[3] Thermistor
Par. 1-93 Thermistor
Ressource set to [2]
Analog input 54
FC 302 series
[4] Relative
reference
Not supported
Parameter 309 Terminal 53, min.
scaling
6-10 Terminal 53 Low
Voltage
[5] Max. torque
frequency
Range
-10.00 – Par. 6-11
Par. 4-21 Speed
Limit Factor Source
set to [6] Analog in
54
Table 5.95 Conversion of Parameter 308
VLT 5000 series
0 – 10.0 Volt
Table 5.96 Conversion of Parameter 309
VLT 5000 series
Table 5.98 Conversion of Parameter 311
FC 302 series
Parameter 310 Terminal 53, max.
scaling
6-11 Terminal 53 High
Voltage
Range
Par. 6-10 - 10.00 Volt
0 – 10.0 Volt
Table 5.97 Conversion of Parameter 310
VLT 5000 series
FC 302 series
Parameter 312 Terminal 54, min.
scaling
6-20 Terminal 54 Low
Voltage
Range
-10.00 – Par. 6-21
0 – 10.0 Volt
Table 5.99 Conversion of Parameter 312
VLT 5000 series
FC 302 series
Parameter 313 Terminal 54, max.
scaling
6-21 Terminal 54 High
Voltage
Range
Par. 6-20 - 10.00 Volt
0 – 10.0 Volt
Table 5.100 Conversion of Parameter 313
MG34N202 - Rev. 2013-10-15
23
5 5
VLT® AutomationDrive FC 302 PROFIBUS Converter Operating Instructions
Parameter Mapping Lists
VLT 5000 series
Parameter 314 Terminal 60,
Analogue Input
current
Options
5 5
FC 302 series
VLT 5000 series
3-17 Reference Resource 3
7-00 Speed PID Feedback Source
1-93 Thermistor Resource
4-20 Torque Limit Factor Source
[0] No Operation
Par. 3-17 Reference resource 3 set
to [0] No function
[1] Reference
Par. 3-17 Reference resource 3 set
to [2] Analog input 54 Par. 7-00
Speed PID
Feedback Source set to [7]
Analog input 54
FC 302 series
Parameter 318 Function after time
out
6-01 Live Zero Timeout
Function
Options
[0] Off
[0] Off
[1] Freeze output
frequency
[1] Freeze output
frequency
[2] Stop
[2] Stop
[3] Jogging
[3] Jog
[4] Max Speed, p202
[4] Max Speed
[5] Stop and trip
[5] Stop and trip
Table 5.105 Conversion of Parameter 318
[2] Feedback
signal
Par. 7-00 Speed PID Feedback
Source set to [7] Analog input 54
[3] Torque limit
Par. 3-17 Reference resource 3 set
to [2] Analog input 54 Par. 4-20
Torque Limit
Factor Source set to [6] Analog in
54
Parameter 319 Terminal 42,
Output
Digital = Par. 5-32 DO X30/7
(MCB 101)
Analogue values = Par. 6-50 AO
42
Pulse = Par. 5-66 DO X30/6
[4] Relative
reference
Not supported
Parameter 321 Terminal 45,
Output
Digital = Par. 5-33 DO X30/7
(MCB 101)
Analogue values= Par. 6-60 AO
X30/8
Pulse = Par. 5-66 DO X30/6
Options
[0] No function
Par. 5-32 = [0] No operation
[1] Control Ready
Par. 5-32 = [1] Control Ready
[2] Ready signal
Par. 5-32 = [2] Drive ready
VLT 5000 series
Comments The HW switch S202 for analogue input 54 must be
set to current (ON).
Table 5.101 Conversion of Parameter 314
VLT 5000 series
FC 302 series
Parameter 315 Terminal 60, min.
scaling
6-22 Terminal 54 Low
Current
Range
0.00 – Par. 6-23
0.0 – 20.0 mA
[3] Ready - Remote Par. 5-32 = [3] Drive rdy/rem
Control
ctrl
[4] Enabled, no
warning
Table 5.102 Conversion of Parameter 315
VLT 5000 series
FC 302 series
Parameter 316 Terminal 60, max.
scaling
6-23 Teminal 54 High
Current
Range
Par. 6-22 - 20.00 mA
0.0 – 20.0 mA
FC 302 series
Table 5.103 Conversion of Parameter 316
Par. 5-32 = [4] Enable / no
warning
[5] Running
Par. 5-32 = [5] VLT® running
[6] Running, no
Warning
Par. 5-32 = [6] Running /no
warning
[7] Running within
range, no Warning
Par. 5-32 = [7] Run in range/no
warning
[8] Run at
reference, no
Warning
Par. 5-32 = [8] Run on ref/no
warning
VLT 5000 series
FC 302 series
[9] Alarm
Par. 5-32 = [9] Alarm
Parameter
317 Time Out
6-00 Live Zero Timeout Time
Range
0 – 99 sec
0 – 99 sec
[10] Alarm or
Warning
Par. 5-32 = [10] Alarm or
Warning
Table 5.104 Conversion of Parameter 317
[11] Torque limit
Par. 5-32 = [11] At torque limit
[12] Out of current
range
Par. 5-32 = [12] Out of current
range
[13] Above I low
Par. 5-32 = [13] Below current,
low 1)
[14] Under I high
Par. 5-32 = [14] Above current,
high 1)
Table 5.106 Conversion of Parameters 319 to 321
24
MG34N202 - Rev. 2013-10-15
VLT® AutomationDrive FC 302 PROFIBUS Converter Operating Instructions
Parameter Mapping Lists
VLT 5000 series
VLT 5000 series
FC 302 series
FC 302 series
Parameter 319 Terminal 42,
Output
Digital = Par. 5-32 DO X30/7
(MCB 101)
Analogue values= Par. 6-50 AO
42
Pulse = Par. 5-66 DO X30/6
Parameter 319 Terminal 42, Output Digital = Par. 5-32 DO
X30/7 (MCB 101)
Analogue values= Par. 6-50
AO 42
Pulse = Par. 5-66 DO X30/6
Parameter 321 Terminal 45,
Output
Digital = Par. 5-33 DO X30/7
(MCB 101)
Analogue values= Par. 6-60 AO
X30/8
Pulse = Par. 5-66 DO X30/6
Parameter 321 Terminal 45, Output Digital = Par. 5-33 DO
X30/7 (MCB 101)
Analogue values= Par. 6-60
AO X30/8
Pulse = Par. 5-66 DO X30/6
Options
[15] Out of
frequency range
Par. 5-32 = [15] Out of speed
range
Options
[16] Over f low
Par. 5-32 = [16] Below speed
[17] Under f high
[28] Brake, no brake
warning
Par. 5-32 = [28] Brake, no
brake warning
low 1)
[29] Brake ready, no
fault
Par. 5-32 = [29] Brake
ready, no fault
Par. 5-32 = [17] Above speed
[30] Brake fault
Par. 5-32 = [30] Brake fault
(IGBT)
high 1)
[18] Out of feedback Par. 5-32 = [18] Out of feedb.
range
Range
[19] Over feedback
low
Par. 5-32 = [19] Below
feedback low 1)
[20] Under feedback Par. 5-32 = [20] Above
high
feedback high 1)
[21] Thermal
warning
Par. 5-32 = [21] Thermal
warning
[22] Ready, no
thermal warning
Par. 5-32 = [12] Ready,no
thermal W
[31] Relay 123
Par. 5-32 = [31] Relay 123
[32] Mechanical brake
control
Par. 5-32 = [32] Mech
brake ctrl
[34] Extended
mechanical brake
control
Par. 5-32 = [32] Mech
brake ctrl
[35] Safety Interlock
Not supported
5 5
[36] 0 – 100 Hz ⇒ 0 – 20 Not supported
mA
[37] 0 – 100 Hz ⇒ 4 – 20 Not supported
mA
[23] Ready - remote Par. 5-32 = [23] Remote, ready,
control - no thermal no TW
warning
[38] 0 – 100 Hz ⇒ 0 –
32000 p
Not supported
[24] Ready – mains Par. 5-32 = [24] Ready, Voltage
voltage within range OK
[39] 0 – f max ⇒ 0 – 20
mA
Par. 6-50 = [109] Max Out
freq. 0 – 20 mA
[25] Reversing
Par. 5-32 = [25] Reverse
[26] Bus OK
Par. 5-32 = [26] Bus OK
[40] 0 – f max ⇒ 4 – 20
mA
Par. 6-50 = [130] Max Out
freq. 4 – 20 mA
[41] 0 – f max ⇒ 0 –
32000 p
Par. 5-66 = [109] Max Out
freq. 0 – 32000p Par. 568 =
32000
[42] Ref min – Ref max
Par. 6-50 = [101] Reference
0 -20 mA
[27] Torque limit and Par. 5-32 = [27] Torque limit &
stop
stop
Table 5.107 Conversion of Parameters 319 to 321
⇒ 0 – 20 mA
Table 5.108 Conversion of Parameters 319 to 321
MG34N202 - Rev. 2013-10-15
25
5 5
Parameter Mapping Lists
VLT 5000 series
VLT® AutomationDrive FC 302 PROFIBUS Converter Operating Instructions
FC 302 series
VLT 5000 series
FC 302 series
Parameter 319 Terminal 42,
Output
Digital = Par. 5-32 DO X30/7
(MCB 101)
Analogue values= Par. 6-50
AO 42
Pulse = Par. 5-66 DO X30/6
Parameter 319 Terminal 42,
Output
Digital = Par. 5-32 DO X30/7
(MCB 101)
Analogue values= Par. 6-50
AO 42
Pulse = Par. 5-66 DO X30/6
Parameter 321 Terminal 45,
Output
Digital = Par. 5-33 DO X30/7
(MCB 101)
Analogue values= Par. 6-60
AO X30/8
Pulse = Par. 5-66 DO X30/6
Parameter 321 Terminal 45,
Output
Digital = Par. 5-33 DO X30/7
(MCB 101)
Analogue values= Par. 6-60
AO X30/8
Pulse = Par. 5-66 DO X30/6
Options
[43] Ref min – Ref max Par. 6-50 = [131] Reference
4 -20 mA
⇒ 4 – 20 mA
Options
[44] Ref min – Ref max Par. 5-66 = [101] Reference
0 – 32000p Par. 5-68 =
⇒ 0 - 32000 p
32000
[45] FB min – FB max
⇒ 0 – 20 mA
[46] FB min – FB max
⇒ 4 – 20 mA
[47] FB min – FB max
⇒ 0 - 32000 p
Par. 6-50 = [102] Feedback 0
-20 mA
Par. 5-66 = [103] Motor
current 0 - 32000p Par. 5-68
= 32000
Not supported
[62] 0 – SyncRPM ⇒ 0
– 32000 p
Not supported
[65] RPM at F max ⇒ 0 Par. 5-66 = [107] Speed
related to norm 0 – 32000p
– 32000 p
Par. 5-68 = 32000
Table 5.110 Conversion of Parameters 319 to 321
VLT 5000 series
FC 302 series
[51] 0 – T lim ⇒ 0 – 20 Par. 6-50 = [104] Torque
related to limit 0 - 20 mA
mA
Parameter 320 Terminal 42 Output,
pulse scaling
5-68 Pulse Output Max
Freq #X30/6
Range
0 – 32000 Hz
[52] 0 – T lim ⇒ 4 – 20 Par. 6-50 = [134] Torque
related to limit 4 - 20 mA
mA
Table 5.111 Conversion of Parameter 320
[53] 0 – T lim ⇒ 0 –
32000 p
Par. 5-66 = [104] Torque
related to limit 0 – 32000p
Par. 5-68 = 32000
[54] 0 – T nom ⇒ 0 –
20 mA
Par. 6-50 = [105] Torque
related to norm 0 - 20 mA
[55] 0 – T nom ⇒ 4 –
20 mA
Par. 6-50 = [135] Torque
related to norm 4 - 20 mA
[56] 0 – T nom ⇒ 0 –
32000 p
Par. 5-66 = [105] Torque
related to norm 0 – 32000p
Par. 5-68 = 32000
[57] 0 – P nom ⇒ 0 –
20 mA
Par. 6-50 = [106] Power
related to norm 0 - 20 mA
[58] 0 – P nom ⇒ 4 –
20 mA
Par. 6-50 = [136] Power
related to norm 4 - 20 mA
[59] 0 – P nom ⇒ 0 –
32000 p
Par. 5-66 = [106] Power
related to norm 0 – 32000p
Par. 5-68 = 32000
1 – 32000 Hz
VLT 5000 series
FC 302 series
Parameter 322 Terminal 45 Output,
pulse scaling
5-68 Pulse Output Max
Freq #X30/6
Range
0– 32000 Hz
1 – 32000 Hz
Table 5.112 Conversion of Parameter 322
Table 5.109 Conversion of Parameters 319 to 321
26
[61] 0 – SyncRPM ⇒ 4
– 20 mA
[64] RPM at F max ⇒ 4 Par. 6-50 = [137] Speed
related to norm 4 - 20 mA
– 20 mA
Par. 5-66 = [102] Feedback 0
– 32000p Par. 5-68 = 32000
[48] 0 – I max ⇒ 0 – 20 Par. 6-50 = [103] Motor
current 0 -20 mA
mA
[50] 0 – I max ⇒ 0 –
32000 p
Not supported
[63] RPM at F max ⇒ 0 Par. 6-50 = [107] Speed
related to norm 0 - 20 mA
– 20 mA
Par. 6-50 = [132] Feedback 4
-20 mA
[49] 0 – I max ⇒ 4 – 20 Par. 6-50 = [133] Motor
current 4 -20 mA
mA
[60] 0 – SyncRPM ⇒ 0
– 20 mA
MG34N202 - Rev. 2013-10-15
VLT® AutomationDrive FC 302 PROFIBUS Converter Operating Instructions
Parameter Mapping Lists
VLT 5000 series
FC 302 series
VLT 5000 series
FC 302 series
Parameter 323, 326
5-40 Function Relay
Parameter 323, 326
5-40 Function Relay
Range
Relay 1
Relay 2
Range
[22] Ready, no
thermal warning
Par. 5-40 = [12] Ready,no
thermal W
Par. 5-40 = [23] Remote, ready,
no TW
01 Relay
04 Relay
[0] No function
Par. 5-40 = [0] No operation
[1] Control Ready
Par. 5-40 = [1] Control Ready
[2] Ready signal
Par. 5-40 = [2] Drive ready
[23] Ready - remote
control - no thermal
warning
[3] Ready - Remote
Control
Par. 5-40 = [3] Drive rdy/rem
ctrl
[24] Ready – mains
Par. 5-40 = [24] Ready, Voltage
voltage within range OK
[4] Enabled, no
warning
Par. 5-40 = [4] Enable / no
warning
[25] Reversing
Par. 5-40 = [25] Reverse
[26] Bus OK
Par. 5-40 = [26] Bus OK
[5] Running
Par. 5-40 = [5] VLT running
[6] Running, no
Warning
Par. 5-40 = [6] Running / no
warning
[27] Torque limit and Par. 5-40 = [27] Torque limit &
stop
stop
[7] Running within
range, no warning
Par. 5-40 = [7] Run in range/no
warn
[8] Run at
reference, no
Warning
Par. 5-40 = [8] Run on ref/no
warn
[9] Alarm
Par. 5-40 = [9] Alarm
[31] Relay 123
Par. 5-40 = [31] Relay 123
[10] Alarm or
Warning
Par. 5-40 = [10] Alarm or
Warning
[32] Mechanical
brake control
[11] Torque limit
Par. 5-40 = [11] At torque limit
Par. 5-40.0 = [32] Mech brake
ctrl
Par. 1-72 = [5] VVC+/Flux
[12] Out of current
range
Par. 5-40 = [12] Out of current
range
[13] Above I low
Par. 5-40 = [13] Below current,
Par. 5-40 = [14] Above current,
high 1)
[15] Out of
frequency range
Par. 5-40 = [15] Out of speed
range
[16] Over f low
Par. 5-40 = [16] Below speed
low 1)
[17] Under f high
[29] Brake ready, no
fault
Par. 5-40 = [29] Brake ready,
no fault
[30] Brake fault
Par. 5-40 = [30] Brake fault
(IGBT)
[34] Extended
mechanical brake
control
Par. 5-40.0 = [32] Mech brake
ctrl
Par. 1-72 = [5] VVC+/Flux
[35] Safety Interlock
Not supported
Table 5.114 Conversion of Parameters 323 to 326
Par.5-40 = [17] Above speed
high 1)
Par. 5-40 = [28] Brake, no
brake warning
[33] Control word bit Par. 5-40 = [36] Control word
11/12
bit 11
Par. 5-40.1 = [37] Control word
bit 12
low 1)
[14] Under I high
[28] Brake, no brake
warning
VLT 5000 series
FC 302 series
Parameter
324 Relay 01, ON delay
5-41 On Delay, Relay
0.00 – 600.00 sec
0.01 – 600.00 sec
[18] Out of
feedback range
Par. 5-40 = [18] Out of feedb.
Range
Range
[19] Over feedback
low
Par. 5-40 = [16] Below feedback
Table 5.115 Conversion of Parameter 324
low 1)
[20] Under feedback Par. 5-40 = [17] Above feedback
high
high 1)
[21] Thermal
warning
Par. 5-40 = [21] Thermal
warning
VLT 5000 series
FC 302 series
Parameter
325 Relay 01, OFF delay
5-42 Off Delay, Relay
Range
0.00 – 600.00 s
0.01 – 600.00 s
Table 5.116 Conversion of Parameter 325
Table 5.113 Conversion of Parameters 323 to 326
VLT 5000 series
FC 302 series
Parameter 327 Pulse reference, max.
freq
5-51 Term. 29 High
Frequency
Range
0 – 110000 Hz
100 – 65000 Hz
Table 5.117 Conversion of Parameter 327
MG34N202 - Rev. 2013-10-15
27
5 5
5 5
VLT® AutomationDrive FC 302 PROFIBUS Converter Operating Instructions
Parameter Mapping Lists
VLT 5000 series
FC 302 series
Parameter
328 Pulse feedback, max. freq
5-56, 5-50, 5-55
Range
100 – 65000 Hz
0 – 110000 Hz
Table 5.118 Conversion of Parameter 328
VLT 5000 series
FC 302 series
Parameter 360 Term. 45, Output
max. scale
6-62 Terminal X30/8 Max.
Scale
Range
0 – 200%
0 – 500%
Table 5.126 Conversion of Parameter 360
VLT 5000 series
FC 302 series
Parameter 329 Encoder feedback
pulse/rev.
5-70 Term 32/33 Pulses
Per Revolution
VLT 5000 series
FC 302 series
Parameter
361 Encoder loss threshold
Not converted
Range
1 – 4096 pulses
Range
0 – 600%
1 – 4096 pulses
Table 5.119 Conversion of Parameter 329
Parameter
Table 5.127 Conversion of Parameter 361
VLT 5000 series
FC 302 series
330 Freeze ref. /output function
Not converted
Table 5.120 Conversion of Parameter 330
VLT 5000 series
FC 302 series
Parameter 345 Encoder loss
timeout
4-32 Motor Feedback Loss
Timeout
Range
0.00 – 60.00 s
0.0 – 60.0 s
Table 5.121 Conversion of Parameter 345
VLT 5000 series
FC 302 series
Parameter 346 Encoder loss
function
4-30 Motor Feedback Loss
Function
Range
[0] Off
[0] Disable
[1] Freeze output
frequency
[4] Freeze output
frequency
[3] Jog
[3] Jog
[4] Max speed
[5] Max speed
[5] Stop and trip
[11] Stop and trip
[7] Select setup 4
[10] Select setup 4
Table 5.122 Conversion of Parameter 346
VLT 5000 series
FC 302 series
Parameter 357 Term. 42, Output
min. scale
6-51 Terminal 42 Output
Min Scale
Range
0 – 200%
0 – 100%
Table 5.123 Conversion of Parameter 357
VLT 5000 series
FC 302 series
Parameter 358 Term. 42, Output
max. scale
6-52 Terminal 42 Output
Max Scale
Range
0 – 200%
0 – 500%
Table 5.124 Conversion of Parameter 358
VLT 5000 series
FC 302 series
Parameter 359 Term. 45, Output
min. scale
6-61 Terminal X30/8 Min.
Scale
Range
0 – 200%
0 – 100%
Table 5.125 Conversion of Parameter 359
28
MG34N202 - Rev. 2013-10-15
VLT® AutomationDrive FC 302 PROFIBUS Converter Operating Instructions
Parameter Mapping Lists
5.5 VLT® 5000 Parameter Group 4
VLT 5000 series
FC 302 series
VLT 5000 series
Parameter 400 Brake function/
over voltage cont.
2-10 Brake Function
2-17 Over-voltage Control
Options
[0] Off
[0] Off
[1] Resistor brake
Par. 2-10 = *1* Resistor brake
Par. 2-17 = [0] Off
[2] Over voltage
control
Par. 2-10 = [0] Off
Par. 2-17 = [2] Enabled
[3] Over voltage
control and stop
Par- 2-10 = [0] Off
Par. 2-17 = [1] Enabled (not at
stop)
405 Reset
14-20 Reset Mode
Options
[0] Manual reset
[0] Off
[1] Automatic reset
x1
[1] Automatic reset x
1
[2] Automatic reset
x2
[2] Automatic reset x
2
[3] Automatic reset
x3
[3] Automatic reset x
3
[4] Automatic reset
x4
[4] Automatic reset x
4
[5] Automatic reset
x5
[5] Automatic reset x
5
[6] Automatic reset
x6
[6] Automatic reset x
6
[7] Automatic reset
x7
[7] Automatic reset x
7
[8] Automatic reset
x8
[8] Automatic reset x
8
[9] Automatic reset
x9
[9] Automatic reset x
9
Table 5.128 Conversion of Parameter 400
VLT 5000 series
FC 302 series
Parameter 401 Brake resistor, [Ω]
30-81 Brake Resistor (ohm)
Options
Power unit dependable
Power unit dependable
Table 5.129 Conversion of Parameter 401
VLT 5000 series
FC 302 series
Parameter 402 Brake power limit,
[kW]
2-12 Brake Power Limit
(kW)
Range
Depends on unit
Depends on unit
VLT 5000 series
FC 302 series
Parameter 403 Power monitoring 2-13 Brake Power Monitoring
Options
[0] Off
[0] Off
[1] Warning
[1] Warning
[2] Trip
[2] Trip
[10] Automatic reset [10] Automatic reset x
x 10
10
Table 5.133 Conversion of Parameter 405
Table 5.130 Conversion of Parameter 402
VLT 5000 series
FC 302 series
Parameter
FC 302 series
Parameter 406 Automatic restart
time
14-21 Automatic Restart
Time
Range
0 – 600 s
0 – 10 s
Table 5.134 Conversion of Parameter 406
Table 5.131 Conversion of Parameter 403
5000 series
VLT 5000 series
FC 302 series
Parameter
404 Brake check
2-15 Brake Check
Options
[0] Off
[0] Off
[1] Warning
[1] Warning
[2] Trip
[2] Trip
FC 302 series
Parameter 407 Mains failure
14-10 Mains Failure
Data range [0] No function
[0] No function
Table 5.132 Conversion of Parameter 404
[1] Controlled ramp
down
[1] Controlled ramp down
[2] Controlled ramp
down and trip
[2] Controlled ramp down
and trip
[3] Coast
[3] Coast
[4] Kinetic back-up
[4] Kinetic back-up
[5] Controlled alarm
suppression
[5] Kinetic back-up, trip
Table 5.135 Conversion of Parameter 407
Parameter
VLT 5000 series
FC 302 series
408 Quick discharge
Not converted
Table 5.136 Conversion of Parameter 408
MG34N202 - Rev. 2013-10-15
29
5 5
5 5
VLT® AutomationDrive FC 302 PROFIBUS Converter Operating Instructions
Parameter Mapping Lists
VLT 5000 series
FC 302 series
Parameter 409 Trip delay torque 14-25 Trip Delay at Torque
Limit
Parameter
Range
Options
0 – 60 s (60=OFF)
0 – 60 s (60=OFF)
Table 5.137 Conversion of Parameter 409
VLT 5000 series
FC 302 series
Parameter 410 Trip delay inverter 14-26 Trip Delay at Inverter
Fault
Range
0 – 35 s
0 – 35 s
Table 5.138 Conversion of Parameter 410
VLT 5000 series
FC 302 series
Parameter 411 Switching frequency 14-01 Switching Frequency
Range
Unsigned 16 (6)
Unsigned 8 (5)
1.5 – 14 kHz
< 2.3 ⇒ 2.0 kHz [2]
2.3 > 2.7 ⇒ 2.5 kHz [3]
2.8 > 3.2 ⇒ 3.0 kHz [4]
3.3 > 3.7 ⇒ 3.5 kHz [5]
3.8 > 4.5 ⇒ 4.0 kHz [6]
4.6 > 5.5 ⇒ 5.0 kHz [7]
5.6 > 6.5 ⇒ 6.0 kHz [8]
VLT 5000 series
FC 302 series
416 Feedback Unit
3-01 Reference/
feedback Unit
[0] None
[0] None
[1] %
[1] %
[2] PPM
[5] PPM
[3] rpm
[2] RPM
[4] bar
[71] bar
[5] Cycle/min
Not supported
[6] Pulse/s
[12] Pulse/s
[7] Unit s/s
Not supported
[8] Unit s/min
Not supported
[9] Unit s/h
Not supported
[10] °C
[60] °C
[11] Pa
[72] Pa
[12] l/s
[20] l/s
[13] m3/s
[23] m3/s
[14] l/min
[21] l/min
[15] m3/min
[24] m3/min
[16] l/h
[22] l/h
[17] m3/h
[25] m3/h
6.6 > 7.5 ⇒ 7.0 kHz [9]
7.6 > 9.0 ⇒ 8.0 kHz [10]
9.1 > ⇒ 10.0 kHz [11]
Table 5.139 Conversion of Parameter 411
VLT 5000 series
FC 302 series
Parameter 412 Output frequency dependent
switching frequency
Not converted
Table 5.140 Conversion of Parameter 412
FC 302 series
[18] kg/s
[30] kg/s
Parameter 413 Overmodulation
function
VLT 5000 series
14-03 Overmodulation
function
[19] kg/min
[31] kg/min
Options
[0] Off
[0] Off
[1] On
[1] On
[20] kg/h
[32] kg/h
[21] t/min
[33] t/min
[22] t/h
[34] t/h
[23] m
[45] m
[24] Nm
[4] Nm
[25] m/s
[40] m/s
Table 5.141 Conversion of Parameter 413
Parameter
VLT 5000 series
FC 302 series
414 Minimum feedback
Not converted
Table 5.142 Conversion of Parameter 414
Parameter
VLT 5000 series
FC 302 series
415 Maximum feedback
Not converted
Table 5.144 Conversion of Parameter 416 part 1
Table 5.143 Conversion of Parameter 415
30
MG34N202 - Rev. 2013-10-15
VLT® AutomationDrive FC 302 PROFIBUS Converter Operating Instructions
Parameter Mapping Lists
Parameter
VLT 5000 series
FC 302 series
416 Feedback Unit
3-01 Reference/
feedback Unit
[26] m/min
[41] m/min
[27] °F
[160] °F
[28] in wg
[172] in wg
VLT 5000 series
FC 302 series
Parameter 420 Speed PID D-gain
limit
7-05 Speed PID Diff. Gain
Limit
Data range 5.0 – 50.0
1.0 – 20.0
Table 5.149 Conversion of Parameter 420
VLT 5000 series
FC 302 series
Parameter 421 Speed PID low-pass
filter
7-06 Speed PID Lowpass
Filter Time
Data range 5.0 – 200.0 ms
1.0 – 100.0
[29] gal/s
[121] gal/s
[30] ft3/s
[125] ft3/s
[31] gal/min
[122] gal/min
[32] ft3/min
[126] ft3/min
[33] gal/h
[123] gal/h
[34] ft3/h
[127] ft3/h
Table 5.151 Conversion of Parameter 422
[35] lb/s
[130] lb/s
VLT 5000 series
FC 302 series
Parameter
422 U0 voltage at 0 Hz
1-55 U0 voltage
Data range
0.0 – par. 103
0.0 – 1000.0 V
VLT 5000 series
FC 302 series
Parameter
423 U1 voltage
1-55 U1 voltage
0.0 – par. 103
0.0 – 1000.0 V
[36] lb/min
[131] lb/min
Data range
[37] lb/h
[132] lb/h
Table 5.152 Conversion of Parameter 423
[38] lb ft
[150] lb ft
[39] ft/s
[140] ft/s
[40] ft/min
[141] ft/min
VLT 5000 series
FC 302 series
Parameter
424 F1 frequency
1-56 F1 frequency
Data range
0.0 – par. 104
0.0 – 1000.0 Hz
Table 5.153 Conversion of Parameter 424
Table 5.145 Conversion of Parameter 416 part2
VLT 5000 series
FC 302 series
Parameter 417 Speed PID proportional gain
7-02 Speed PID proportional gain
Data range 0.000 – 0.150
0.000 – 1.000
Table 5.146 Conversion of Parameter 417
VLT 5000 series
FC 302 series
Parameter 418 Speed PID Integral
Time
7-03 Speed PID proportional gain
Data range 2.0 – 999.9
2.0 – 20000.0
Table 5.147 Conversion of Parameter 418
VLT 5000 series
FC 302 series
Parameter 419 Speed PID Differentiation Time
7-04 Speed PID Differentiation Time
Data range 0.0 – 200.0
0.0 – 200.0
Table 5.148 Conversion of Parameter 419
5 5
Table 5.150 Conversion of Parameter 421
VLT 5000 series
FC 302 series
Parameter
425 U2 voltage
1-55 U2 voltage
Data range
0.0 – par. 103
0.0 – 1000.0 V
Table 5.154 Conversion of Parameter 425
VLT 5000 series
FC 302 series
Parameter
426 F2 frequency
1-56 F2 frequency
Data range
0.0 – par. 104
0.0 – 1000.0 Hz
Table 5.155 Conversion of Parameter 426
VLT 5000 series
FC 302 series
Parameter
427 U3 voltage
1-55 U3 voltage
Data range
0.0 – par. 103
0.0 – 1000.0 V
Table 5.156 Conversion of Parameter 427
VLT 5000 series
FC 302 series
Parameter
428 F3 frequency
1-56 F3 frequency
Data range
0.0 – par. 104
0.0 – 1000.0 Hz
Table 5.157 Conversion of Parameter 428
MG34N202 - Rev. 2013-10-15
31
5 5
VLT® AutomationDrive FC 302 PROFIBUS Converter Operating Instructions
Parameter Mapping Lists
VLT 5000 series
FC 302 series
Parameter
429 U4 voltage
1-55 U4 voltage
VLT 5000 series
Data range
0.0 – par. 103
0.0 – 1000.0 V
438 Process PID Anti 7-31 Process PID
windup
Anti Windup
Options
[0] Off
[0] Off
[1] On
[1] On
Table 5.158 Conversion of Parameter 429
VLT 5000 series
FC 302 series
Parameter
430 F4 frequency
1-56 F4 frequency
Data range
0.0 – par. 104
0.0 – 1000.0 Hz
Table 5.159 Conversion of Parameter 430
VLT 5000 series
FC 302 series
Parameter
431 U5 voltage
1-55 U5 voltage
Data range
0.0 – par. 103
0.0 – 1000.0 V
FC 302 series
Parameter
Table 5.165 Conversion of Parameter 438
VLT 5000 series
FC 302 series
Parameter
439 Process PID
start frequency
7-32 Process PID
Start Speed
Data range
Fmin – fmax
0 – 6000 rpm
Table 5.166 Conversion of Parameter 439
Table 5.160 Conversion of Parameter 431
VLT 5000 series
FC 302 series
Parameter
432 F5 frequency
1-56 F5 frequency
Data range
0.0 – par. 104
0.0 – 1000.0 Hz
VLT 5000 series
FC 302 series
Parameter
440 Process PID
proportional gain
7-33 Process PID
proportional gain
Data range
0.00 – 10.00
0.00 – 10.00
Table 5.167 Conversion of Parameter 440
Table 5.161 Conversion of Parameter 432
VLT 5000 series
FC 302 series
Parameter
441 Process PID
integral time
7-34 Process PID
integral time
0.01 – 9999.99
0.01 – 10000.00
VLT 5000 series
FC 302 series
Parameter
433 Torque control,
open loop proportional gain
7-12 Torque PI
Integration Time
Data range
Data range
0 (Off) – 500%
0 (Off) – 500%
Table 5.168 Conversion of Parameter 441
Table 5.162 Conversion of Parameter 433
VLT 5000 series
FC 302 series
Parameter
434 Torque control,
open loop integral
time
7-13 Torque PI
Integration Time
Data range
0.002 – 2.000 sec
0.002 – 2.000 sec
Options
FC 302 series
442 Process PID
differentiation time
7-35 Process PID
Differentiation Time
Data range
0.00 – 10.00
0.00 – 10.00
Table 5.169 Conversion of Parameter 442
Table 5.163 Conversion of Parameter 434
Parameter
VLT 5000 series
Parameter
VLT 5000 series
FC 302 series
437 Process PID
Normal/Inverse
contr
7-30 Process PID
Normal/ Inverse
Control
[0] Normal
[0] Normal
VLT 5000 series
443 Process PID diff. 7-36 Process PID
gain limit
Diff. Gain Limit
Data range
5.0 – 50.0
[1] Inverse
VLT 5000 series
FC 302 series
444 Process PID
lowpass filter time
Not supported
Table 5.171 Conversion of Parameter 444
Table 5.164 Conversion of Parameter 437
32
0.00 – 10.00
Table 5.170 Conversion of Parameter 443
Parameter
[1] Inverse
FC 302 series
Parameter
MG34N202 - Rev. 2013-10-15
Parameter Mapping Lists
VLT® AutomationDrive FC 302 PROFIBUS Converter Operating Instructions
VLT 5000 series
FC 302 series
Parameter
445 Flying start
1-73 Flying Start
Options
[0] Off
[0] Disable
[1] On
[1] Enable
Parameter
VLT 5000 series
FC 302 series
455 Frequency
range monitor
Not supported
Table 5.180 Conversion of Parameter 455
Table 5.172 Conversion of Parameter 445
VLT 5000 series
FC 302 series
Parameter
446 Switching
pattern
14-00 Switching
Pattern
Options
[0] 60 AVM
[0] 60 AVM
[1] SFAVM
[1] SFAVM
VLT 5000 series
FC 302 series
Parameter
457 Phase loss
functions
14-12 Function at
Mains Imbalance
Options
[0] Trip
[0] Trip
[1] Warning
[1] Warning
5 5
Table 5.181 Conversion of Parameter 457
Parameter
Table 5.173 Conversion of Parameter 446
Parameter
VLT 5000 series
FC 302 series
447 Torque
compensation
Not supported
VLT 5000 series
FC 302 series
483 Dynamic DC
link compensation
Not supported
Table 5.182 Conversion of Parameter 483
Table 5.174 Conversion of Parameter 447
Parameter
VLT 5000 series
FC 302 series
448 Gear ratio
Not supported
Table 5.175 Conversion of Parameter 448
Parameter
VLT 5000 series
FC 302 series
449 Friction loss
Not supported
Table 5.176 Conversion of Parameter 449
VLT 5000 series
FC 302 series
Parameter
450 Mains voltage
at mains fault
14-11 Mains Voltage
at Mains Fault
Range
180 – 690 V
100 – 800 V
Table 5.177 Conversion of Parameter 450
VLT 5000 series
FC 302 series
Parameter
453 Gear ratio,
speed close loop
7-07 Speed PID
Feedback Gear Ratio
Range
0.01 – 100.00
0.0001 – 32.0000
Table 5.178 Conversion of Parameter 453
Parameter
VLT 5000 series
FC 302 series
454 Dead time
compensation
Not supported
Table 5.179 Conversion of Parameter 454
MG34N202 - Rev. 2013-10-15
33
5 5
VLT® AutomationDrive FC 302 PROFIBUS Converter Operating Instructions
Parameter Mapping Lists
5.6 VLT® 5000 Parameter Group 5
VLT 5000 series
FC 302 series
Parameter
500 Address
8-31 Address
Parameter
Range
0 - 126
0 - 126
Table 5.190 Conversion of Parameter 514
Table 5.183 Conversion of Parameter 500
Parameter
VLT 5000 series
FC 302 series
Parameter
501 Baud rate
8-32 FC Port Baud Rate
Options
[0] 300
Not supported
[1] 600
Not supported
[2] 1200
Not supported
[3] 2400
[0] 2400
[4] 4800
[1] 4800
[5] 9600
[2] 9600
FC 302 series
514 Bus time interval function
Not Converted
VLT 5000 series
FC 302 series
515 Reference %
16-02 Reference %
Table 5.191 Conversion of Parameter 515
Parameter
VLT 5000 series
FC 302 series
516 Reference Unit
16-01 Reference [Unit]
Table 5.192 Conversion of Parameter 516
Parameter
Table 5.184 Conversion of Parameter 501
VLT 5000 series
VLT 5000 series
VLT 5000 series
FC 302 series
517 Feedback
16-52 Feedback[Unit]
Table 5.193 Conversion of Parameter 517
FC 302 series
Parameter
502 Coasting
8-50 Coasting Select
Parameter
503 Quick - Stop
8-51 Quick Stop Select
Parameter
504 DC brake
8-52 DC Brake Select
Parameter
VLT 5000 series
FC 302 series
518 Frequency
16-13 Frequency
Table 5.194 Conversion of Parameter 518
Parameter
505 Start
8-53 Start Select
Parameter
506 Reversing
8-54 Reversing Select
Parameter
507 Setup select
8-55 Set-up Select
Parameter
508 Preset reference
select
8-56 Preset Reference
Select
Parameter
type
Unsigned 8 (5)
Unsigned 8 (5)
Options
[0] Digital input
[0] Digital input
[1] Bus
[1] Bus
[2] Logic AND
[2] Logic AND
[3] Logic OR
[3] Logic OR
Parameter
VLT 5000 series
FC 302 series
519 Frequency x scaling
Not converted
Table 5.195 Conversion of Parameter 519
Parameter
VLT 5000 series
FC 302 series
520 Current
16-14 Motor current
Table 5.196 Conversion of Parameter 520
VLT 5000 series
Parameter 521 Torque
Table 5.185 Conversion of Parameter 502 - 508
FC 302 series
16-22 Torque [%]
16-21 Torque [%] high resolution
VLT 5000 series
FC 302 series
Parameter
509 Bus Jog 1
8-90 Bus Jog 1 Speed
Range
0.0 – par. 202
0.0 – par. 4-13
Table 5.197 Conversion of Parameter 521
Parameter
Table 5.186 Conversion of Parameter 509
VLT 5000 series
FC 302 series
Parameter
510 Bus Jog 2
8-91 Bus Jog 2 Speed
Range
0.0 – par. 202
0.0 – par. 4-13
VLT 5000 series
FC 302 series
522 Power, kW
16-10 Power [kW]
Table 5.198 Conversion of Parameter 522
Parameter
VLT 5000 series
FC 302 series
523 Power, HP
16-11 Power [hp]
Table 5.187 Conversion of Parameter 510
Table 5.199 Conversion of Parameter 523
VLT 5000 series
FC 302 series
Parameter
512 Telegram Profile
8-10 Control Word Profile
Range
[0] Fieldbus profile
[1] ProfiDrive profile
[1] FC profile
[0] FC profile
Parameter
VLT 5000 series
FC 302 series
513 Bus time interval
Not Converted
Table 5.189 Conversion of Parameter 513
34
FC 302 series
524 Motor voltage
16-12 Motor Voltage
Table 5.200 Conversion of Parameter 524
Table 5.188 Conversion of Parameter 512
Parameter
VLT 5000 series
Parameter
VLT 5000 series
FC 302 series
525 DC link voltage
16-30 DC Link Voltage
Table 5.201 Conversion of Parameter 525
MG34N202 - Rev. 2013-10-15
VLT® AutomationDrive FC 302 PROFIBUS Converter Operating Instructions
Parameter Mapping Lists
Parameter
VLT 5000 series
FC 302 series
526 Motor temp.
16-18 Motor Thermal
Parameter
VLT 5000 series
FC 302 series
536 Brake power/s
16-32 Brake Energy /s
Table 5.202 Conversion of Parameter 526
Parameter
Table 5.212 Conversion of Parameter 536
VLT 5000 series
FC 302 series
527 VLT® temp.
16-35 Inverter Thermal
Parameter
Table 5.203 Conversion of Parameter 527
VLT 5000 series
FC 302 series
Parameter 528 Digital input
16-60 Digital Input
Options
Term. 16 (binary 0000 0001)
Term. X30/2 (binary)
Term. 17 (binary 0000 0010)
Term. X30/3 (binary)
Term. 18 (binary 0000 0100)
Term. 18 (binary)
Term. 19 (binary 0000 1000)
Term. 19 (binary)
Term. 27 (binary 0001 0000)
Term. 27 (binary)
Term. 32 (binary 0010 0000)
Term. 32 (binary)
Term. 33 (binary 0100 0000)
Term. 33 (binary)
VLT 5000 series
FC 302 series
537 Heat sink temp
16-34 Heatsink Temp.
Table 5.213 Conversion of Parameter 537
Parameter
VLT 5000 series
FC 302 series
538 Alarm word
14-72 Legacy Alarm Word
5 5
Table 5.214 Conversion of Parameter 538
Parameter
VLT 5000 series
FC 302 series
539 VLT® Control word
16-00 Control Word
Table 5.215 Conversion of Parameter 539
Table 5.204 Conversion of Parameter 528
Parameter
VLT 5000 series
FC 302 series
529 Analogue input 53
16-62 Analog Input 53
Parameter
FC 302 series
540 Warning word
14-73 Legacy Warning Word
Table 5.216 Conversion of Parameter 540
Table 5.205 Conversion of Parameter 529
VLT 5000 series
* = Switch “S201” must be OFF
Parameter
VLT 5000 series
Parameter 541 Extended status
word
VLT 5000 series
FC 302 series
530 Analogue input 54
16-64 Analog Input 54
FC 302 series
14-74 Leg. Ext. Status
Word
Table 5.217 Conversion of Parameter 541
Table 5.206 Conversion of Parameter 530
** = Switch “S202” must be OFF
Parameter
Parameter
VLT 5000 series
FC 302 series
531 Analogue input 60
16-64 Analog Input 54
Parameter
Parameter
FC 302 series
532 Pulse reference
16-51 Pulse Reference
Table 5.208 Conversion of Parameter 532
VLT 5000 series
Not converted
VLT 5000 series
FC 302 series
554 Display text 2
Not converted
Table 5.219 Conversion of Parameter 554
VLT 5000 series
Parameter 533 External reference %
FC 302 series
553 Display text 1
Table 5.218 Conversion of Parameter 553
Table 5.207 Conversion of Parameter 531
*** = Switch “S202” must be ON
VLT 5000 series
Parameter
VLT 5000 series
FC 302 series
557 Motor RPM
16-17 Speed [RPM]
Table 5.220 Conversion of Parameter 557
FC 302 series
16-50 External Reference
VLT 5000 series
FC 302 series
558 Motor RPM x scaling
Not converted
Table 5.209 Conversion of Parameter 533
Parameter
VLT 5000 series
FC 302 series
534 Status word, binary
16-03 Status Word
Parameter
Table 5.221 Conversion of Parameter 558
Table 5.210 Conversion of Parameter 534
VLT 5000 series
Parameter 535 Brake power/2 min
FC 302 series
16-33 Brake Energy /2 min
Table 5.211 Conversion of Parameter 535
Parameter
number
VLT 5000 series
FC 302 series
580, 581, 582 Define
parameter
Not converted
Table 5.222 Conversion of Parameter 580-582
MG34N202 - Rev. 2013-10-15
35
5 5
VLT® AutomationDrive FC 302 PROFIBUS Converter Operating Instructions
Parameter Mapping Lists
5.7 VLT® 5000 Parameter Group 6
Parameter
VLT 5000 series
FC 302 series
600 Operating hours
15-00 Operating hours
Parameter
VLT 5000 series
FC 302 series
611 Data log: Motor frequency
Not converted
Table 5.234 Conversion of Parameter 611
Table 5.223 Conversion of Parameter 600
Parameter
VLT 5000 series
FC 302 series
601 Hours run
15-01 Running Hours
Parameter
VLT 5000 series
FC 302 series
612 Data log: Motor voltage
Not converted
Table 5.235 Conversion of Parameter 612
Table 5.224 Conversion of Parameter 601
Parameter
VLT 5000 series
FC 302 series
602 kWh counter
15-02 kWh Counter
Parameter
VLT 5000 series
FC 302 series
613 Data log: Motor current
Not converted
Table 5.236 Conversion of Parameter 613
Table 5.225 Conversion of Parameter 602
Parameter
VLT 5000 series
FC 302 series
603 Numbers of power up
15-03 Power Up's
Parameter
VLT 5000 series
FC 302 series
614 Data log: DC link voltage
Not converted
Table 5.237 Conversion of Parameter 614
Table 5.226 Conversion of Parameter 603
VLT 5000 series
Parameter
VLT 5000 series
FC 302 series
604 Numbers of over temp.
15-04 Over Temp's
FC 302 series
Parameter 615 Fault log: Error code 15-30 Fault Log: Error Code
Table 5.238 Conversion of Parameter 615
Table 5.227 Conversion of Parameter 604
Parameter
VLT 5000 series
FC 302 series
605 Numbers of over voltage
15-05 Over Volt's
Parameter
Parameter
Parameter
FC 302 series
606 Data log: Digital input
Not converted
FC 302 series
616 Fault log: Time
15-32 Fault Log: Time
Table 5.239 Conversion of Parameter 616
Table 5.228 Conversion of Parameter 605
VLT 5000 series
VLT 5000 series
VLT 5000 series
FC 302 series
617 Fault log: Value
15-31 Fault Log: Value
Table 5.240 Conversion of Parameter 617
Table 5.229 Conversion of Parameter 606
VLT 5000 series
FC 302 series
Parameter 618 Reset of kWh counter 15-06 Reset kWh Counter
Parameter
VLT 5000 series
FC 302 series
607 Data log: Bus commands
Not converted
Table 5.230 Conversion of Parameter 607
Parameter
VLT 5000 series
FC 302 series
608 Data log: Status word
Not converted
VLT 5000 series
FC 302 series
609 Data log: Reference
Not converted
VLT 5000 series
VLT 5000 series
FC 302 series
610 Data log: Feedback
Not converted
FC 302 series
15-07 Reset Running Hours
Counter
Options
[0] No reset
[0] Do not reset
[1] Reset
[1] Reset counter
Table 5.242 Conversion of Parameter 619
Table 5.233 Conversion of Parameter 610
36
[0] Do not reset
[1] Reset counter
Parameter 619 Reset of Hours
run
Table 5.232 Conversion of Parameter 609
Parameter
[0] No reset
[1] Reset
Table 5.241 Conversion of Parameter 618
Table 5.231 Conversion of Parameter 608
Parameter
Options
MG34N202 - Rev. 2013-10-15
VLT® AutomationDrive FC 302 PROFIBUS Converter Operating Instructions
Parameter Mapping Lists
VLT 5000 series
FC 302 series
Parameter
Parameter 620 Operation mode
14-22 Operation Mode
Options
[0] Normal operation
[0] Normal operation
[1] Function with deactivated Not supported
inverter
[2] Control card test
[2] Control card test
[3] Initialisation
[3] Initialisation
VLT 5000 series
FC 302 series
630 Name plate: Com. type
Not converted
Table 5.253 Conversion of Parameter 630
Parameter
VLT 5000 series
FC 302 series
631 Name plate: Com. Type no.
Not converted
Table 5.254 Conversion of Parameter 631
Table 5.243 Conversion of Parameter 620
Parameter
VLT 5000 series
FC 302 series
621 Name plate: VLT® type
Not converted
5 5
Table 5.244 Conversion of Parameter 621
Parameter
VLT 5000 series
FC 302 series
622 Name plate: Power section
Not converted
Table 5.245 Conversion of Parameter 622
VLT 5000 series
Parameter 623 Name plate: VLT® ordering no.
FC 302 series
Not converted
Table 5.246 Conversion of Parameter 623
VLT 5000 series
FC 302 series
Parameter 624 Name plate: Software version no. Not converted
Table 5.247 Conversion of Parameter 624
Parameter
VLT 5000 series
FC 302 series
625 Name plate: LCP ID no.
Not converted
Table 5.248 Conversion of Parameter 625
Parameter
VLT 5000 series
FC 302 series
626 Name plate: Data base ID
Not converted
Table 5.249 Conversion of Parameter 626
Parameter
VLT 5000 series
FC 302 series
627 Name plate: Power ID no.
Not converted
Table 5.250 Conversion of Parameter 627
VLT 5000 series
Parameter 628 Name plate: Application type
FC 302 series
Not converted
Table 5.251 Conversion of Parameter 628
VLT 5000 series
FC 302 series
Parameter 629 Name plate: Application type no. Not converted
Table 5.252 Conversion of Parameter 629
MG34N202 - Rev. 2013-10-15
37
VLT® AutomationDrive FC 302 PROFIBUS Converter Operating Instructions
Parameter Mapping Lists
5.8 VLT® 5000 Parameter Group 7
VLT 5000 series
VLT 5000 series
FC 302 series
FC 302 series
Parameter 700 System control
8-02 Control Word Source
33-82 Drive Status Monitoring
Parameter 707 PID Velocity Feedforward
32-65 Velocity FeedForward
Options
[0] Enable SyncPos
Par. 8-02: [5] Option C0
Par. 33-82: [1] On
Options
0 – 100000
[1] Disable SyncPos
Par. 8-02: [1] FC RS-485
[2] Enable SyncPos
without VLT
monitoring
Par. 8-02: [5] Option C0
Par. 33-82: [0] Off
5 5
Table 5.255 Conversion of Parameter 700
Parameter
Options
VLT 5000 series
FC 302 series
701 Program
number
33-80 Activated
Program Number
-1 – 127
-1 – 127
0 – 65000
Table 5.262 Conversion of Parameter 707
VLT 5000 series
FC 302 series
Parameter 708 PID Acceleration
Feed-forward
32-66 Acceleration FeedForward
Options
0 – 100000
0 – 65000
Table 5.263 Conversion of Parameter 708
VLT 5000 series
FC 302 series
Parameter 709 PID Velocity filter
33-26 Velocity Filter
Options
-1073741824 – 107374203
-500000 – 500000
Table 5.264 Conversion of Parameter 709
Table 5.256 Conversion of Parameter 701
VLT 5000 series
FC 302 series
Parameter 702 PID Proportional factor 32-60 Proportional factor
Parameter
710 - 779
19-10 -19-79
Options
Options
User defined
User defined
VLT 5000 series
FC 302 series
0 – 65000
0 – 100000
Table 5.265 Conversion of Parameters 710 to 779
Table 5.257 Conversion of Parameter 702
Parameter
Options
VLT 5000 series
FC 302 series
703 PID Derivative
factor
32-61 Derivative
factor
0 – 65000
0 – 100000
VLT 5000 series
FC 302 series
Parameter
780 Dead time compensation
Not supported
Options
[0] Off
[1] On
Table 5.266 Conversion of Parameter 780
Table 5.258 Conversion of Parameter 703
VLT 5000 series
FC 302 series
VLT 5000 series
FC 302 series
Parameter
704 PID Integral factor
32-62 Integral factor
Parameter
781 Program ID
Not supported
Options
0 – 65000
0 – 100000
Options
0 – 65000
Table 5.267 Conversion of Parameter 781
Table 5.259 Conversion of Parameter 704
VLT 5000 series
VLT 5000 series
FC 302 series
Parameter 705 PID Integral
bandwidth
32-63 Limit Value for
Integral Sum
Parameter 795 - 799 User defined
(read only)
Options
0 – 1000
Options
0 – 1000
19-95 -19-99 User
defined (read only)
User defined
Table 5.268 Conversion of Parameters 795 to 799
Table 5.260 Conversion of Parameter 705
VLT 5000 series
FC 302 series
Parameter
706 PID Active bandwidth
32-64 PID Bandwidth
Options
0 – 65000
0 – 1000
Table 5.261 Conversion of Parameter 706
38
User defined
FC 302 series
MG34N202 - Rev. 2013-10-15
VLT® AutomationDrive FC 302 PROFIBUS Converter Operating Instructions
Parameter Mapping Lists
5.9 VLT® 5000 Parameter Group 8
Parameter
VLT 5000 series
FC 302 series
800 PROFIBUS DP
Not converted
VLT 5000 series
FC 302 series
801 Baud rate selection
Not converted
Table 5.270 Conversion of Parameter 801
Parameter
VLT 5000 series
FC 302 series
808 ProfiDrives status word
Not converted
Table 5.276 Conversion of Parameter 808
Table 5.269 Conversion of Parameter 800
Parameter
Parameter
VLT 5000 series
FC 302 series
802 Minimum station delay
Not converted
VLT 5000 series
FC 302 series
Parameter 849 Extended diagnose
8-07 Diagnosis Trigger
Options
[0] Disable
[0] Disable
[1] Alarm
[1] Trigger on alarm
[2] Alarm and warnings
[2] Trigger on alarm/warn.
Table 5.277 Conversion of Parameter 849
Table 5.271 Conversion of Parameter 802
VLT 5000 series
FC 302 series
Parameter 803 Time out after bus
error
8-03 Control Word Timeout
Time
Range
0.1 – 18000.0
1 – 99
Table 5.272 Conversion of Parameter 803
VLT 5000 series
Parameter 804 Response after bus
time out
FC 302 series
8-04 Control Word Timeout
Function
8-02 Control Word Source
Range
[0] Off
[0] Off
[1] Freeze output
frequency
[1] Freeze output
frequency
[2] Stop
[2] Stop
[3] Jogging
[3] Jogging
[4] Max speed
[4] Max speed
[5] Stop and trip
[5] Stop and trip
[6] No com. option
control
Par. 802 to RS485
[7] Select set up 4
[10] Select set up 4
Table 5.273 Conversion of Parameter 804
VLT 5000 series
FC 302 series
Parameter 805 Function of control
word bit 10
8-14 Configurable
Control Word CTW
Range
[0] None
[0] No function
[1] Bit 10 = 1 => CTW active [1] Profile default
[2] Bit 10 = 0 => CTW active [2] CTW Valid, active
low
[3] Bit 10 = 1 => Time out
[1] Profile default
Table 5.274 Conversion of Parameter 805
Parameter
VLT 5000 series
FC 302 series
806 SAP selection (FMS)
Not converted
Table 5.275 Conversion of Parameter 806
MG34N202 - Rev. 2013-10-15
39
5 5
5 5
Parameter Mapping Lists
VLT® AutomationDrive FC 302 PROFIBUS Converter Operating Instructions
5.10 VLT® 5000 Parameter Group 9
Parameter
VLT 5000 series
FC 302 series
900 Write PPO type 1
Not converted
VLT 5000 series
FC 302 series
901 Write PPO type 2
Not converted
Table 5.279 Conversion of Parameter 901
Parameter
VLT 5000 series
FC 302 series
902 Write PPO type 3
Not converted
VLT 5000 series
FC 302 series
903 Write PPO type 4
Not converted
VLT 5000 series
FC 302 series
904 PPO type select for DP
Not converted
VLT 5000 series
FC 302 series
907 Read PPO type 1
Not converted
Options
[0] None
[0] None
[204] Minimum Reference
[302] Minimum
Reference
[205] Maximum Reference
[203] Maximum
Reference
[219] Catch up/slow Down
Value
[312] Catch up/slow
Down Value
[207] Ramp 1 Ramp up
Time
[341] Ramp 1 Ramp up
Time
[208] Ramp 1 Ramp Down
Time
[342] Ramp 1 Ramp
Down Time
[209] Ramp 2 Ramp up
Time
[351] Ramp 2 Ramp up
Time
[210] Ramp 2 Ramp down
Time
[352] Ramp 2 Ramp
down Time
[211] Jog Ramp Time
[380] Jog Ramp Time
[212] Quick Stop Ramp
Time
[381] Quick Stop Ramp
Time
[201] Motor Low Limit [Hz] [412] Motor Speed Low
Limit [Hz]
Table 5.283 Conversion of Parameter 907
Parameter
VLT 5000 series
FC 302 series
908 Read PPO type 2
Not converted
[202] Motor High Limit [Hz] [414] Motor Speed High
Limit [Hz]
Table 5.284 Conversion of Parameter 908
Parameter
[417] Torque Limit
Generator Mode
[509] Bus Jog 1 Speed
[890] Bus Jog 1 Speed
Not converted
[510] Bus Jog 2 Speed
[891] Bus Jog 2 Speed
Comments VLT® 5000 supports more write signals. If a notsupported signal is written then the corresponding
VLT 5000 series
FC 302 series
910 Read PPO type 4
Not converted
signal is set to [0] None.
Table 5.290 Conversion of Parameter 915
VLT 5000 series
FC 302 series
911 PPO type for FMS read
Not converted
VLT 5000 series
FC 302 series
913 Broadcast index
Not converted
Table 5.288 Conversion of Parameter 913
40
[222] Torque Limit
Generator Mode
FC 302 series
Table 5.287 Conversion of Parameter 911
Parameter
[416] Torque Limit
Motor Mode
909 Read PPO type 3
Table 5.286 Conversion of Parameter 910
Parameter
[221] Torque Limit Motor
Mode
VLT 5000 series
Table 5.285 Conversion of Parameter 909
Parameter
FC 302 series
9-15 PCD Write Configuration
Table 5.282 Conversion of Parameter 904
Parameter
Not converted
VLT 5000 series
Table 5.281 Conversion of Parameter 903
Parameter
FC 302 series
914 Broadcast off-set
Parameter 915 PCD config write
Table 5.280 Conversion of Parameter 902
Parameter
VLT 5000 series
Table 5.289 Conversion of Parameter 914
Table 5.278 Conversion of Parameter 900
Parameter
Parameter
MG34N202 - Rev. 2013-10-15
VLT® AutomationDrive FC 302 PROFIBUS Converter Operating Instructions
Parameter Mapping Lists
VLT 5000 series
FC 302 series
Parameter 916 PCD config read
9-16 PCD Read Configuration
Options
[0] None
[0] None
[538] Alarm word
[1472] VLT Alarm Word
[540] Warning word
[1473] VLT Warning Word
[541] Ext. status word
[1474] VLT Ext. status
Word
[600] Operating hours
[1500] Operating hours
[601] Running hours
[1501] Running hours
[602] kWh Counter
[1502] kWh Counter
[539] Control word
[1600] Control word
[516] Reference [Unit]
[1601] Reference [Unit]
[515] Reference %
[1602] Reference %
[534] Status word
[1603] Status word
[522] Power [kW]
[1610] Power [kW]
[523] Power [HP]
[1611] Power [HP]
[524] Motor voltage
[1612] Motor voltage
[518] Motor frequency
[1613] Motor frequency
[520] Motor current
[1614] Motor current
[557] Motor RPM
[1617] Motor speed
[526] Motor thermal
[1618] Motor thermal
[521] Torque
[1622] Torque %
[525] DC link voltage
[1630] DC link voltage
[536] Brake energy/s
[1632] Brake energy/s
VLT 5000 series
FC 302 series
Parameter
927 Parameter edit
9-27 Parameter Edit
Options
[0] Disable
[0] Disable
[1] Enable
[1] Enable
Table 5.294 Conversion of Parameter 927
VLT 5000 series
FC 302 series
Parameter
928 Control authority
9-28 Process Control
Options
[0] Disable
[0] Disable
[1] Enable
[1] Enable cyclic master
VLT 5000 series
[1634] Heat sink temp.
[527] Inverter Thermal
[1635] Inverter Thermal
[533] External reference
[1650] External reference
[532] Pulse reference
[1651] Pulse reference
[517] Feedback [Unit]
[1652] Feedback [Unit]
[528] Digital input
[1660] Digital input
[529] Analog input 53
[1662] Analog input 53
[530] Analog input 54
[1664] Analog input 54
[531] Analog input 60
[1664] Analog input 54
Table 5.296 Conversion of Parameter 953
Parameter
VLT 5000 series
FC 302 series
964 Identification
9-64 Device Identification
Table 5.297 Conversion of Parameter 964
Parameter
VLT 5000 series
FC 302 series
965 Profile Number
9-65 Profile Number
Table 5.298 Conversion of Parameter 965
Parameter
VLT 5000 series
FC 302 series
967 Control word (FMS)
Not converted
Table 5.299 Conversion of Parameter 967
Parameter
VLT 5000 series
FC 302 series
968 Status word (FMS)
Not converted
Table 5.300 Conversion of Parameter 968
VLT 5000 series
FC 302 series
Parameter 970 Parameter set-up selection 9-70 Edit Set-up
Table 5.291 Conversion of Parameter 916
Parameter
FC 302 series
Parameter 953 Warning parameter 9-53 Profibus Warning Word
[535] Brake energy/2 min [1633] Brake energy/2 min
[537] Heat sink temp.
5 5
Table 5.295 Conversion of Parameter 928
Options
[0] Factory setting
[0] Factory setting
[1] Parameter setup 1
VLT 5000 series
FC 302 series
[1] Parameter setup 1
917 Spontaneous messages
Not converted
[2] Parameter setup 2
[2] Parameter setup 2
[3] Parameter setup 3
[3] Parameter setup 3
[4] Parameter setup 4
[4] Parameter setup 4
[5] Active setup
[9] Active setup
Table 5.292 Conversion of Parameter 917
VLT 5000 series
FC 302 series
Parameter
918 Station address
9-18 Node Address
Range
0 - 125
0 - 125
Table 5.301 Conversion of Parameter 970
Table 5.293 Conversion of Parameter 918
MG34N202 - Rev. 2013-10-15
41
5 5
VLT® AutomationDrive FC 302 PROFIBUS Converter Operating Instructions
Parameter Mapping Lists
VLT 5000 series
FC 302 series
Parameter 971 Save data values 9-71 Profibus Save Data Values
Options
Unsigned 8 (5)
Unsigned 8 (5)
[0] Not active
[0] Off
[1] Save active setup [1] Store all setups
[2] Save edit setup
[1] Store all setups
[3] Save all setups
[1] Store all setups
Table 5.302 Conversion of Parameter 971
VLT 5000 series
FC 302 series
Parameter 980, 981, 982, 990 Modified
parameters
Not converted
Table 5.303 Conversion of Parameter 980-990
42
MG34N202 - Rev. 2013-10-15
VLT® AutomationDrive FC 302 PROFIBUS Converter Operating Instructions
Troubleshooting
6 Troubleshooting
6.1 Step-by-step Troubleshooting
After copying the station address from the VLT® 5000 to
the VLT® AutomationDrive FC 302, power must be cycled
to the FC 302. The master/PLC should now recognise FC
302 as a VLT® 5000. The NS LED on the MCA 114 option
should now be solid green indicating that communication
between master and slave is established.
6 6
If the NS LED flashes, the master/PLC has not recognized
the FC 302:
•
Check if station address is the same in the FC 302
as the replaced VLT® 5000.
•
Check 9-63 Actual Baud Rate. If the frequency
converter has a connection to the master, this
parameter displays the detected baudrate. If no
master has been detected, the parameter
displays: “No baud rate found”.
•
Check 9-53 Profibus Warning Word.
Bit
Warn. Word
[Hex]
Description
0
0001
Connection with DP-master is not OK
1
0002
Unused
2
0004
FDL (Field-bus Data link Layer) is not
OK
3
0008
Clear data command received
4
0010
Actual value is not updated
5
0020
Baudrate search
6
0040
PROFIBUS ASIC is not transmitting
7
0080
Initialising of PROFIBUS is not ok
8
0100
Drive is tripped
9
0200
Internal CAN error
10
0400
Wrong configuration data from PLC
11
0800
Wrong ID sent by PLC
12
1000
Internal error occurred
13
2000
Not configured
14
4000
Timeout active
15
8000
Warning 34 active
Table 6.1 Warning Word
•
Check 1.3 Constraints for more information on
limitations.
MG34N202 - Rev. 2013-10-15
43
Index
VLT® AutomationDrive FC 302 PROFIBUS Converter Operating Instructions
Index
T
Terminal..................................................................................................... 4
A
Abbreviations.......................................................................................... 5
Troubleshooting.................................................................................. 43
B
W
Brake chopper......................................................................................... 3
Warning word....................................................................................... 43
C
Commissioning.................................................................................... 10
Configuration.......................................................................................... 3
Constrains................................................................................................. 3
D
DIP switches............................................................................................. 9
E
EMC precautions.................................................................................... 8
H
Hardware................................................................................................... 4
High voltage............................................................................................ 6
I
Installation................................................................................................ 7
L
LEDs........................................................................................................... 10
Linked Set-ups........................................................................................ 5
Literature................................................................................................... 3
M
MCA 114.................................................................................................. 43
Mechanical Installation....................................................................... 8
N
Node address........................................................................................... 9
O
Overview (technical)............................................................................ 3
P
Parameter (mapping list)................................................................. 12
Performance............................................................................................ 5
Power size................................................................................................. 3
44
MG34N202 - Rev. 2013-10-15
Index
VLT® AutomationDrive FC 302 PROFIBUS Converter Operating Instructions
MG34N202 - Rev. 2013-10-15
45
www.danfoss.com/drives
130R0371
MG34N202
*MG34N202*
Rev. 2013-10-15
">