Simplicity 00602-1 Operator's Manual

GENERAC 6000CP
High Pressure Washer
Owner’s Manual
. Operating Instructions and Maintenance
TETE
aa, E ee re V ASS
p A A » и Ea CC ICC u - я NIP
' i
0
NN
“a,
way,
OÙ
nd *
\\
Ре RO
SA 5 Y \\
KERR À
: М
E \
o % N
RO as’
+
su v
Model No. 0602-1 (3 gpm High Pressure Washer) Manual No. 99915 (Revision 0 6/17/96)
THIS SYMBOL POINTS OUT IMPORTANT SAFETY INSTRUCTIONS, WHICH, iF NOT FOLLOWED, COULD ENDANGER THE
PERSONAL SAFETY AND/OR PROPERTY OF YOURSELF AND OTHERS. READ AND FOLLOW ALL INSTRUCTIONS IN THE
MANUAL BEFORE ATTEMPTING TO OPERATE THIS UNIT.
CAUTION: ALWAYS DISCONNECT SPARK PLUG WIRE AND PLACE WIRE WHERE IT CANNOT CONTACT SPARK PLUG, TO
PREVENT ACCIDENTAL STARTING WHEN SETTING UP, TRANSPORTING, ADJUSTING OR MAKING REPAIRS TO YOUR
HIGH PRESSURE WASHER.
EH TRAINING
Engine exhaust gases contain DEADLY carbon monoxide gas. This dan-
gerous gas, if breathed in sufficient concentrations, can cause
unconsciousness or even death. Operate this equipment only in the
open air where adequate ventilation is available.
A WARNING: A
The engine exhaust from this product
contains chemicals known to the State
of California to cause cancer, birth
defects, or other reproductive harm.
Gasoline is highly FLAMMABLE and its vapors are EXPLOSIVE. Do not
permit smoking, open flames, sparks or heat in the vicinity while han-
ding gasoline. Avoid spilling gasoline on a hot engine. Aliow unit to cool
for 2 minutes before refueling. Comply with all laws regulating storage
and handling of gasoline.
Locate this pressure washer in areas away from combustible materials,
combustible fumes or dust.
The high pressure equipment is designed to be used with Generac autho-
rized parts only. If you use this equipment with parts that do not comply
with minimum specifications, the user assumes all risks and liabilities.
Some chemicals or detergents may be harmful if inhaled or ingested, caus-
ing severe nausea, fainting or poisoning. The harmful elements may cause
property damage or severe injury.
Do not allow CHILDREN to operate the Pressure Washer at any time.
EH PREPARATION
* Operate engine only at governed speed. Running the engine at exces-
sive speeds increases the hazard of personal injury. Do not tamper with
parts which may increase or decrease the governed speed.
Do not wear loose clothing, jewelry or anything that may be caught in
the starter or other rotating parts.
Before starting the Pressure Washer in cold weather, check all parts of
the equipment and be sure ice has not formed there.
Units with broken or missing parts, or without protective housing or
covers should NEVER be operated.
The muffler and air cleaner must be installed and in good condition
before operating the Pressure Washer, These components act as spark
arrestors if the engine backfires.
Check the fuel system for leaks or signs of deterioration such as chafed
or spongy hose, loose or missing clamps or damaged tank or cap. Cor-
rect all defects before operating the Pressure Washer.
HB OPERATION
+ Do not spray flammable liquids.
* Never aim the gun at people, animals or plants.
+ High pressure spray can cause paint chips or other particles to become
airborne and fly at high speeds.
Never allow any part of the body to come in contact with the fluid stream.
DO NOT come in contact with a fluid stream created by a leak in the high
pressure hose.
High pressure stream of fluid that this equipment can produce can pierce
skin and its underlying tissues, leading to serious injury and possible ampu-
tation.
Always wear eye protection when you use this equipment or when you
are in the vicinity where the equipment is in use.
Operate the pressure at no more than the PSI fluid pressure rated for
your pressure washer.
Never move the machine by pulling on the high pressure hose. Use the
handle provided on the top of the unit.
Always be certain the spray gun, nozzles and accessories are correctly
attached.
Never use a spray gun which does not have a trigger lock or trigger guard
in place and in working order.
Use a respirator or mask whenever there is a chance that vapors may
be inhaled. Read all instructions with mask so you are certain the mask
will provide the necessary protection against inhaling harmful vapors.
High pressure spray may damage fragile items including glass. Do not
point spray gun at glass when in the jet spray mode.
Keep the hose connected to machine or the spray gun while the system
is pressurized. Disconnecting the hose while the unit is pressurized is
dangerous.
Hold the spray gun firmly in your hand before you start the unit. Failure
to do so could result in an injury from a whipping spray gun. Do not leave
the spray gun unattended while the machine is running.
The cleaning area should have adequate slopes and drainage to reduce
the possibility of a fall due to slippery surfaces.
Keep water spray away from electric wiring or fatal electric shock may
result.
Do not adjust unloader valve to a pressure in excess of machine rating.
Do not secure trigger gun in the pull-back (open) position.
Do not by-pass any safety device on this machine.
Do not leave trigger closed for more than 5 minutes with engine running.
This could damage the pump.
The muffler and engine heat up during operation and remain hot imme-
diately after shutting it down. Avoid contact with a hot muffler or engine
or you could be severely burned.
E MAINTENANCE AND STORAGE
+ Operate and store this unit on a stable surface.
+ High pressure hose can develop leaks from wear, kinking, abuse, etc.
Water spraying from a leak is capable of injecting material into skin. Inspect
hose each time before using it. Check all hoses for cuts, leaks, abrasions
or bulging of cover, or damage or movement of couplings. If any of these
conditions exist, replace hose immediately. Never repair high pressure
hose. Replace it with another hose that meets minimum pressure rating
of your pressure washer.
High Pressure Washer
EE
Generac 6000CP High Pressure Washer
Sa Specifications
eo
hose. Replace it with another hose that meets minimum pressure rating
of your pressure washer.
CONGRATULATIONS on your purchase of a GENERAC high
pressure washer. It has been designed, engineered and man-
ufactured to give you the best possible dependability and
performance.
Should you experience any probiem you cannot easily remedy,
please contact your nearest GENERAC Authorized Sevice
facility, or call the 1-800 number listed on the front of this
manual. We have competent, well-trained technicians and
— the proper tools to service or repair this unit.
Please read and retain this manual. The instructions will
MODEL
NUMBER 0602-1
SERIAL
NUMBER
DATE OF
PURCHASE
THE MODEL AND SERIAL NUMBERS WILL BE FOUND
ON A DECAL ATTACHED TO THE PRESSURE WASHER.
YOU SHOULD RECORD BOTH SERIAL NUMBER AND
DATE OF PURCHASE AND KEEP IN A SAFE PLACE
FOR FUTURE REFERENCE.
enable you to assemble and maintain your high pressure
washer properly. Always observe the "SAFETY RULES!
CUSTOMER RESPONSIBILITIES
* Read and observe the safety rules.
‘+ Follow regular schedule in maintaining, caring for and using
your high pressure washer.
es Follow the instructions under “Maintenance” and “Storage”
sections of this Owner's Manual.
PRODUCT SPECIFICATIONS
PRESSURE WASHER SPECIFICATIONS
OUTLET PRESSURE Adjustable to 2000 psi
FLOW RATE 3 Gallons per minute
DETERGENT MIX Use undiluted detergent
WATER SUPPLY
TEMPERATURE Not to exceed 140°F
SUCTION HEIGHT 3 FT. maximum
ENGINE SPECIFICATIONS
ENGINE MODEL GN-Series
RATED HORSEPOWER 6.5
DISPLACEMENT 190cc
SPARK PLUG: Type: Champion RC12YC
or equivalent
Set Gap To: 0.030 inch (0.76mm)
| GASOLINE CAPACITY 1 U.S. gallon
OIL (20 oz. capacity) SAE 30 weight
SOLID STATE IGNITIONAIR GAP 0.0125 inch
NOTE: The engine of your pressure washer is equipped with
a spark arrestor muffler. The spark arrestor must be main-
tained in effective working order by the owner/operator.
In the State of California a spark arrestor is required by law
(Section 4442 of the California Public Resources Code). Other
states may have similar laws. Federal laws apply on federal
lands.
High Pressure Washer
A
3
Generac 6000CP High Pressure Washer
oF Contents
of
р Hardware
> Pack
PARTS PACKED SEPARATELY IN CARTON
= = ; e - | > N
y Ш —
Parts Bag
, . Handle
Main Unit
High Pressure Hose Spray Gun Wand
PARTS BAG CONTENTS
Chemical Injector Tube
Nozzle Cleaning Kit (aa (2) Plastic Handle Knobs
(2) Carriage Bolts — 1/4”-20 x 1%”
High Pressure Washer
—
4
Generac 6000CP High Pressure Washer
Row
Your
l’ressure
Washer
READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR HIGH PRESSURE WASHER. Compare
the illustrations with your high pressure washer to familiarize yourself with the locations of various controls and adjustments.
Save this manual for future reference.
GUIDE HANDLE
FUEL TANK 7
GUN/WAND ASSEMBLY
HIGH PRESSURE HOSE
INTAKE SUPPLY FILTER
DETERGENT PICKUP
TUBE AND FILTER
PRESSURE 7
REGULATOR
N —
HIGH PRESSURE —
OUTLET
PRESSURE REGULATOR — Allows you to adjust the pres- INTAKE SUPPLY FILTER — Filters inlet water supply.
sure of the outlet stream. DETERGENT PICKUP TUBE AND FILTER — Mixes water and
ENGINE ON-OFF CONTROL — Sets engine in starting mode detergent in outlet water flow.
for recoil starter: turns OFF running engine. HIGH PRESSURE OUTLET — Connection for high pressure
AIR CLEANER - Dry type filter element limits the amount oi hose.
dirt and dust that gets in the engine. RECOIL STARTER — Used for starting the engine manually.
GUN AND WAND ASSEMBLY— Controls the application of
water onto cleaning surface with trigger device. Includes safety
latch.
High Pressure Washer
а
5
Generac 6000CP High Pressure Washer
#
Read these instructions and Operator's Manual in its entirety * Place the guidle handle into the slots on the legs already 4
before you attempt to assemble or operate your new high connected to the main unit. Align the holes. Hold one side :
pressure washer. Your high pressure washer has, for the most of the handle as shown in STEP 1 and apply inward pres- |
part, been assembled at the factory. Before you can operate sure with your thumb. This should allow you enough room >»
your new high pressure washer, you must attach the guide to slide the handle into the slots and align the holes. |
handle and properly connect the high pressure hose andthe, |nsert the carriage bolts through the holes as shown in illus-
water supply. tration for Step 1 and attach the plastic knobs. Tighten the
IF YOU HAVE ANY PROBLEMS WITH THE ASSEMBLY OF knobs by hand.
YOUR PRESSURE WASHER, PLEASE CALL THE PRES- Note that one end of the hi :
. gh pressure hose is covered with
SURE WASHER HELPLINE AT 1-800-270-1408. teflon tape. If tape is not properly applied, reapply it so
threads are fully covered. The tape seals the connection from
Ш TOOLS NEEDED hose to spray gun.
You will need (2) large adjustable wrenches or (2) sets of Step 2 — ATTACH HOSE TO GUN
large pliers OR one adjustable wrench and one set of pliers.
Ш TO REMOVE PRESSURE WASHER FROM | MZ |
САКТОМ ' #2
Remove the guide handle wrapped in plastic.
« Remove the 50-foot high pressure hose.
Remove the two accessories bags and the goggles Teron
Refer to Page 4, “Contents of Hardware Pack" for an illustrated
listing of all the items included with your pressure washer.
Become familiar with each piece before assembling the pres-
sure washer. Check all contents against the illustrations on
Page 4. If any parts are missing or damaged, call the pres-
sure washer helpline at 1-800-270-1408.
STEP 1 - ATTACH THE GUIDE HANDLE
INSERT CARRIAGE
BOLTS
« Attach gun to end of high pressure hose covered with teflon
tape. Use two adjustable wrenches to tighten the fitting.
High Pressure Washer
—
6
Step 3 — CONNECT GARDEN HOSE TO WATER
INLET OPENING
e Check inlet screen to be sure it is not damaged.
* Aftach garden hose to the water inlet.
* Check that high pressure hose is attached to pump outlet
and spray gun.
CAUTION: You must assemble the spray gun and
attach all hoses before you start the engine. Start-
A
damage the pump.
* Open the water faucet as far as it will go (40 Ibs. of water
pressure
Step 4 — SQUEEZE TRIGGER TO PURGE PUMP
SYSTEM OF AIR AND IMPURITIES
у!
1 LA /
Ша
N
ing the engine without all the hoses connected will
CAUTION: Before starting the pressure washer, be
sure you are wearing adequate eye protection.
Goggles are included with this unit.
Step 5 — CONNECT NOZZLE EXTENSION TO
SPRAY GUN
BEFORE YOU CAN START USING YOUR NEW PRESSURE
WASHER, YOU MUST PREPARE THE ENGINE.
"OIL FILL OPENING
Hl ADD ENGINE OIL BEFORE INITIAL START
Remove one of the yellow Oil Fill Caps and add engine oil until
oil level is at point of overflowing. Check engine oil level before
starting each time thereafter. If oil level is below point of over-
flowing, fill to proper level.
A
CAUTION: Any attempt to crank or start the engine
before it has been properly serviced with the rec-
ommended oil results in an engine failure.
High Pressure Washer
pm
7
INSTALLATION 7 NONI Generac 6000CP High Pressure Washer
TN
y
7
E
The recommended oils include the following:
* During summer months: SAE 30. SAE 10W-30 is an accept-
able substitute.
* During winter months: 5W-30. DO NOT USE 10W-40.
Crankcase oil capacity is about 620m or about 20 fluid ounces.
Use no special additives.
Ш STEP 7 — ADD FUEL
Use regular UNLEADED gasoline,and add slowly, to fuel tank.
You may also use regular leaded gasoline if UNLEADED is
not available. Fuel capacity is one (1) U.S. gallon (4 liters).
CAUTION: Do not overfill the fuel tank. Always
A allow room in the fuel tank for expansion.
WARNING: NEVER FILL FUEL TANK INDOORS.
A NEVER FILL FUEL TANK WHEN ENGINE IS RUN-
NING OR HOT. DO NOT SMOKE WHEN FILLING
FUEL TANK.
The pump is supplied complete with oil, but before you use
the pressure washer, you must remove the red cap from the
oil fill hole on the pump and insert the Oil Breather Cap into
the pump (Step 8).
Check that the oil level is correct at the oil lever window. If you
need to add oil, use 80W-90 Gear Lube.
Step 8 — INSTALL OIL BREATHER CAP INTO
WATER PUMP
Step 9 — PLACE ENGINE RUN-STOP SWITCH TO
“RUN” POSITION. >
=
— RUN
Las STOP
o ри
Step 10 — OPEN FUEL SHUT-OFF VALVE T.
CLOSED
=
NOTE: The spray gun includes a SAFETY LATCH that allows
you to prevent trigger actuation. Use it after the engine is
started to prevent the washer from inadvertantly spraying
while you prepare chemical application or perform other tasks.
Step 11 — SET SAFETY LATCH ON GUN HANDLE
High Pressure Washer
Tr"
8
E Generac 6000CP High Pressure Washer
Step 12 — FOR COLD ENGINE, MOVE LEVERTO
FULL CHOKE POSITION
For warm engine, move choke lever to half choke or "RUN"
position.
* Press trigger on pressure washer gun.
Grasp engine starter recoil handle and pull once.
* When engine starts, move choke lever to RUN position. If
engine fails to start, move choke lever to RUN position and
pull starter rope (2 pulls max.)
e If engine still fails to start, move choke lever to FULL posi-
tion, press trigger on pressure washer gun and pul! starter
recoil handle once.
—e
CAUTION: Do not run pump without water supply
A connected. Do not allow pump to run for more than
5 minutes without pulling the trigger on spray gun.
If not in use for more than 5 minutes without
pulling trigger, relieve pressure and shut off unit.
You must foilow this caution or the pump will be
damaged.
STOPPING YOUR PRESSURE
WASHER
First move engine RUN-STOP switch to STOP position.
Simply shutting OFF engine will not release pres-
A sure in the system. When engine has shut down,
pull the trigger on the gun to relieve the pressure in
the hose.
HOW TO USE YOUR WASHER
You now should know how to START your pressure washer
and how to STOP it. The information in this section will tell you
how to adjust the spray pattern and apply detergent or any
other cleaning chemicals.
Bl HOW TO USE ADJUSTABLE NOZZLE
WARNING: NEVER ADJUST SPRAY PATTERN WHEN
SPRAYING. NEVER PUT HANDS IN FRONT OF SPRAY
NOZZLE TO ADJUST SPRAY PATTERN. YOU COULD BE
INJURED.
ON COIN-OPERATED TYPE PRESSURE WASHERS IF YOU
WANT TO CHANGE THE SPRAY FORCE, YOU EITHER
PRESS A BUTTON OR TURN A DIAL.
YOUR ENGINE-POWERED PRESSURE WASHER HAS NO
BUTTONS TO PUSH OR DIALS TO TURN.
On the end of your spray gun is a nozzle that you can slide
forward and backward and that you can also twist from side to
side. This adjustable nozzle takes the place of buttons or dials.
With the adjustable nozzle you can adjust the spray pattern to
be either high pressure or low pressure. You can also adjust
the spray so itis concentrated in a stream pattern or expanded
into a fan pattern. Use this nozzle to apply detergent.
« Slide the nozzle forward when you wish to adjust the spray
to low pressure mode (Fig. 13 on Page 10). Slide the nozzle
backward to achieve high pressure.
* Point the nozzle toward the ground and press the trigger to
test the pattern (Fig. 14 on Page 10).
High Pressure Washer
Tr
Generac 6000CP High Pressure Washer
. Low Pressure _ ff | a .
will ONLY work 7
when nozzle is in
correct setting. м y) I
ENS
= SD
~~ J |
UNE ZI
=>} TT
L7
> DA /
и”
NOZZLE IN HIGH PUSH NOZZLE FORWARD FOR TWIST NOZZLE TO TWIST NOZZLE TO
PRESSURE MODE LOW PRESSURE MODE AND EXPAND SPRAY STREAM NARROW SPRAY STREAM
DETERGENT APPLICATION
* If you get the spray nozzle too close, especially using high
: Testina the $ " pressure mode, you may damage the cleaning surface.
Figure 14 — Testing the Spray Pattern * Do not get closer than 6 inches when cleaning automobile
tires.
ci
mM
Ш INJECTING CLEANING AGENTS
- —
| 1. Ifyou use a detergent or wax, connect the clear plastic tube
into the injector fitting on the pump (Fig. 15). Then place
a Sin 4 A the small filter in the detergent container.
; PA |
PAN Figure 15 — Setting up Chemical Injector System
Vi Zu
CAUTION: Keep the plastic injector tube from
: Ч J 3 A coming in contact with the hot muffier. This will
e Tuvicti damage the plastic tube. When inserting the filter
Twisting the nozzle adjusts the spray pattern from a narrow into a cleaning agent bottle route the tube so as to
stream to an expanded stream.
keep it from inadvertently contacting the hot muffler.
* For most effective cleaning, keep spray nozzle between 8 O
to 24 inches of cleaning surface.
7 <=
High Pressure Washer
—
10
NOTE: You can order multi-purpose cleaner/degreaser (Part
#88181); car wash detergent (Part #88182); and car wax (Part
#88183) from Generac. See your Dealer/Distributor.
A pressure washers. Household detergents could
damage the pump.
2. Set nozzle to low pressure Be sure to use the LOW PRES-
SURE mode when applying detergent or wax. Refer to
“ADJUST NOZZLE" diagram.
3. Press trigger.
4. Adjust knob on injector (Fig. 16) for concentration of deter-
gent-to-water that you want for your cleaning job.
CAUTION: Use soaps designed specifically for
Figure 16 — Adjusting Chemical Concentration
Generac detergents and cleaning agents.
EN TO CLEAN
Start at lower portion of area to be washed and work upward,
using long, even overlapping strokes. Detergent or degreaser
works best when you apply it to a dry surface first. Let it set
for 3-5 minutes before washing and rinsing.
Hl RINSE
Push the nozzle sleeve to high pressure and wait for deter-
gent to clear. Start at the top of area to be rinsed, working down
with the same action as for cleaning.
NOTE: Never use garden hose inlet to siphon detergent or
Wax.
E TO STOP
If you have used chemical injector hose you must flush it with
clean water before stopping the engine. Place the injector
filter into a pail of clear water while running Pressure Washer
with nozzle in low pressure mode. Flush for five minutes.
1. To shut off the pump, move Engine RUN-STOP Switch to
STOP position.
2.Simply shutting OFF engine will not release pressure in the
sysiem. When engine has shut down, pullthe trigger on the
gun to relieve the pressure in the hose.
MN PRESSURE WASHER ACCESSORIES
* Cleaning Agents: Multipurpose Detergent (order #88181):
Car Wash (order #88182); Car Wax (order #88183)
* Turbo Nozzle (order #90580)
* Rotating Brush Kit (order #89080)
* Under Body Lance (order #89076)
Utility Brush Kit (order #89079)
+ 50-foot Hose Extension (order #92500)
PREPARING THE UNIT FOR
STORAGE
Water should not remain in the unit for long periods of time.
Sediments of minerals can deposit on pump parts and “freeze”
pump action. If you do not plan to use the Pressure Washer
for more than 30 days, follow this procedure:
1. Flush detergent hose by placing the injector filter into a pail
of clear water while running Pressure Washer with nozzle
in low pressure mode. Flush for five minutes.
J. Place engine RUN-STOP Switch in STOP position.
A CAUTION: Be sure switch is in “STOP” position
proper water supply connected, you can damage
pump.
about 6 times. This should remove most of the liquid in the pump.
NOTE: To protect unit from freezing temperatures, draw wind-
fluid into a 3-foot section of garden hose connected to inlet
adaptor and pulling recoil handle twice.
2. Shut off the engine and let it cool, then remove all hoses.
before you continue. If you start engine without
4. Empty the pump of all pumped liquids by pulling recoil handle
shield washer fluid into pump by pouring windshield washer
5. Store in a clean, dry area.
High Pressure Washer
Tr
11
Generac 6000CP High Pressure Washer
—
a
=
fd
_
_—
=
fy
LL
oF
7 .
1. Clean area around oil drain plug, remove plug and drain oil
completely into a suitable container (Figure 17).
H ENGINE PREPARATION
WARNING: NEVER STORE ENGINE WITH FUEL IN
AA. | TANK INDOORS OR IN ENCLOSED, POORLY VEN-
TILATED AREAS WHERE FUMES MAY REACH AN
OPEN FLAME, SPARK OR PILOT LIGHT AS ON A
FURNACE, WATER HEATER, CLOTHES DRYER OR
OTHER GAS APPLIANCE.
NOTE: If you did use “gasohol”, run engine until engine stops
from lack of fuel.
+ While engine is still warm, drain oil from crankcase. Refill
with fresh oil. See “PREPARING WASHER FOR FIRST
USE" for oil recommendations.
+ Remove spark plug and pour about 1/2 ounce (15mi) of
engine oil into the cylinder. Cover spark plug hole with rag.
Crank slowly to distribute oil.
A CAUTION! Avoid spray from spark plug hole when
cranking engine slowly.
* Install spark plug. Do not connect spark plug wire.
ENGINE MAINTENANCE
Ш CHECKING OIL LEVEL
See “PREPARING WASHER FOR FIRST USE" for informa-
tion on checking oil level. Oil level should be checked prior to
each use or at least every eight hours of operation. Keep oil
level maintained.
EM CHANGING OIL
Change oil after first 8 hours of operation. Change oil every
50 hours thereafter. If you are using your pressure washer
under extremely dirty or dusty conditions, or in extremely hot
weather, change oil more often.
Change oil while engine is still warm, as follows:
A CAUTION: Disconnect spark plug wire from spark
plug and keep it away from spark plug.
Figure 17 — Draining Oil from Engine
su Ti
Ml
HH
«<=>
i
——OIL DRAIN PLUG
2. When all oil has drained, install and tighten oil drain plug.
3. Remove oil fill plug and insert a clean fill funnei into plug
opening. Fill engine crankcase with recommended oil until
oil level is at point of overflowing. Do not overfill above that
mark. About 21 ounces is required. POUR SLOWLY.
4. When engine crankcase is filled to proper level, install and
tighten oil fill plug.
HB REPLACE SPARK PLUG
Change the spark plug every 100 hours of operation or once
each year, whichever comes first. This will help your engine
to start easier and run better. Replace with Champion RC12YC
or equivalent type spark plug. Set spark plug gap (Figure 18)
to 0.030 inch (0.76mm).
Figure 18 — Setting Spark Plug Gap
ST 0.030* FEELER GAUGE
(0.76mm)
a Te
ОРДЕН О у
nN
à 7 |
High Pressure Washer
—
12
Generac 6000CP High Pressure Washer
Ш SERVICE AIR CLEANER
Your engine will not run properly and may be damaged if you
run it using a dirty air cleaner.
Clean or replace the air cleaner paper filter once every 25 hours
of operation or once a year, whichever comes first. Clean or
replace more often if operating under dusty or dirty conditions.
Clean foam pre-filter every 25 hours of operation or sooner
under dusty conditions.
CAUTION: Never run this unit without the com-
A plete air cleaner system installed on the engine.
This could result in premature wear to the engine.
To clean or replace foam pre-cleaner:
1. Remove air cleaner cover, then foam pre-Cleaner (Figure 19).
Figure 19 — Removing Pre-filter and Air Filter
1711/11 NS
И НР
i р
Г
:
|
}
Ty A
UNEN
2. Wash pre-filter in soap water. Squeeze pre-cleaner dry in
clean cloth (DO NOT TWIST). Saturate pre-cleaner in clean
engine oil and then wrap pre-cleaner in clean dry cloth to
squeeze out excess oil (DO NOT TWIST).
3. Clean air cleaner cover before installing it.
TO CLEAN OR REPLACE PAPER AIR FILTER:
1. Remove air cleaner cover; then remove foam pre-filter (ser-
vice if necessary) and remove paper filter.
2. Clean air filter by tapping it gently on a solid surface. If the
filter is too dirty, replace it with a new one. Dispose of the
old filter properly.
3. Clean air cleaner cover then insert pre-filter into cover. Next
insert new paper filter into cover to hold pre-filter in place
and assemble all of them to base of air cleaner.
HE ENGINE ACCESSORIES
* Service Kit [includes air cleaner, spark plug, wrench, screw
driver and fuel additive] (order #84684)
* Air Filter (order #84892)
EM CLEAN SPARK ARRESTOR SCREEN
The engine exhaust muffler has a spark arrestor screen.
Inspect and clean the screen every 100 hours of operation or
once each year, whichever comes first.
WARNING: LET THE MUFFLER COOL BEFORE
A | WORKING ON IT. CONTACT WITH A HOT MUFFLER
OR ENGINE CAN CAUSE SEVERE BURNS.
NOTE: If you use your pressure washer on any forest-cov-
ered, brush-covered or grass-covered unimproved land, it
must have a spark arrestor. The spark arrestor must be main-
tained in good condition by the owner/operator.
Clean and inspect the spark arrestor as follows:
1. To remove the muffler guard from the muffler, remove the
three screws that connect the guard to the muffler bracket
(Figure 20).
Figure 20 — Removing Muffler Guard
and Spark Arrestor
SPARK ARRESTOR
MUFFLER
HEAT SHIELD
2. Remove four screws that attach the spark arrestor screen.
3. Inspect screen and replace if torn, perforated or otherwise
damaged. DO NOT USE a defective screen. If screen is
not damaged, clean it with commercial solvent.
4. Reattach the screen and the muffler guard.
High Pressure Washer
rer
Generac 6000CP High Pressure Washer
PUMP MAINTENANCE
HE PURGE PUMP OF AIR AND CONTAMINANTS
To remove the air from the pump, follow these steps:
+ Set up the pressure washer as described in the ASSEM-
BLY section and connect the water supply.
+ Remove the nozzle attachment from the gun.
* Pull the trigger on the gun and hold.
To remove the contaminants from the pump, follow these steps:
es Set up the pressure washer as described in the ASSEM-
BLY section, connect the water supply and start the engine
according to instructions in the OPERATION section.
+ Remove the nozzle attachment from the gun.
* Pull the trigger on the gun and hold.
* When the water supply is steady and constant, you may
refasten the nozzle attachment and start the pump.
EH NOZZLE MAINTENANCE
If the nozzle becomes restricted or clogged with foreign
materials, such as dirt, excessive pump pressure may
develop. A partially clogged nozzle can cause a pulsing
sensation during use. This generally is not a pump related
problem, but rather a clogged or partially restricted nozzle.
If the nozzle becomes clogged or partially restricted, imme-
diately clean the nozzle with the kit included with your
pressure washer by following these instructions:
* Shut off the engine and turn off the water supply.
* Separate the wand from the gun.
» Remove nozzle from the end of the wand using a 2mm or
5/64 allen wrench (like the one included in the kit).
« Use the wire included in the kit (Fig. 21) or a small paper clip to
free the foreign materials clogging or restricting the nozzle.
Figure 21 — Free Foreign Materials
ia |
—> za
» Remove additional debris by back flushing water supply
through wand (Fig. 22). Back flush between 30 to 60 sec-
onds. Turn wand to stream spray and move nozzle from low
to high while flushing.
Figure 22 — Back Flush Water
* Reinstall nozzle into the wand. DO NOT overtighten.
Reconnect the wand to the gun
Reconnect the water supply, turn on the water, and start the
engine.
Test the pressure washer by operating with nozzle in the high
and in the low position.
LOW OIL PRESSURE
SHUTDOWN SYSTEM
The engine is equipped with a low oil pressure sensor that shuts
down the engine automatically when the oil pressure drops
below 6 psi. If the engine shuts down by itself and the fuel tank
has enough gasoline, check engine oil level.
E INITIAL STARTUP
A delay built in the shutdown system allows oil pressure to build
during starting. The delay allows the engine to run for about
10 seconds before sensing oil pressure.
B SENSING LOW PRESSURE
If the system senses low oil pressure during operation, the
engine shuts down. As the system shuts down, the low oil light
comes ON. However, once the engine has stopped rotating,
this light will go OFF.
High Pressure Washer
er
EH RESTARTING
If you try to restart the engine within 5 seconds after it shuts
down, the engine may NOT start. The system needs 5 to 10
seconds to reset.
you do restart the engine after such a shutdown and have
not corrected the low oil pressure, the engine runs for about
10 seconds as described above and then stops.
SERVICE AND ADJUSTMENTS
Ш ENGINE SPEED
CAUTION: Engine speed was properly adjusted at
the factory and should require no additional
adjustment. Do not attempt to change engine
speed. If you believe the engine is running too fast
or too slow, take your pressure washer to autho-
rized service center for repair and adjustment.
CHANGING ENGINE GOVERNED SPEED WILL
VOID ENGINE WARRANTY.
A
Your pressure washer runs at a constant speed. This constant
operating speed is maintained by a mechanical, flyweight
type, fixed speed governor. DO NOT try to adjust the governed
speed setting for the following reasons:
* High engine speeds are dangerous and increase the risk
of personal injury or damage to equipment.
* Low engine speeds impose a heavy load on the engine when
sufficient engine power is not available and may shorten
engine life.
EH ADJUSTING THE CARBURETOR
The carburetor of your pressure washer is pre-set at the fac-
tory. The carburetor should not be tampered with. If your
pressure washer is used at an altitude above 5,000 feet, con-
sult your Generace service facility regarding high altitude
jetting changes.
High Pressure Washer
rer”
15
Generac 6000CP High Pressure Washer
TROUBLE
SHOOTING
&
7
TROUBLESHOOTING POINTS ;
PROBLEM
Pump has following problems:
failure to produce pressure, erratic
pressure, chattering, loss of pressure,
low water volume.
Detergent fails to mix with spray.
gent.
Engine runs good at no-load but ©bogs
when load is added.
Engine will not start; or starts
and runs rough
CAUSE
1.Nozzie in low pressure mode.
2.Low regulator pressure
3. Water inlet is blocked.
4.Inadequate water supply
5. Inlet hose is kinked or leaking
6. Clogged inlet hose strainer.
7.Detergent line is not submerged.
8. Water supply is over 140*F.
9. Outlet hose is blocked or leaks.
10. Gun leaks.
11.Nozzle is obstructed.
12. Pump is faulty.
1. Detergent line is not submerged.
2. Chemical filter is clogged.
3. Nozzle is in high pressure mode.
4. Chemical adjuster is closed.
Engine speed is too slow.
1. Low oil level
2. Dirty air cleaner
3. Out of gasoline.
4. Stale gasoline.
High Pressure Washer
rer
16
CORRECTION :
1. Pull nozzle backward for high
pressure mode.
. Adjust regulator to desired setting.
. Clear inlet
. Provide adequate water flow.
. Straighten inlet hose, patch leak.
. Check and clean inlet hose
strainer.
. Submerge detergent line.
. Provide cooler water supply.
9. Clear blocks in outlet hose.
10. Replace gun.
11. Clear nozzle.
12. Contact Generac service facility.
a Oh &S& wr
o y
0 -
1. Insert chemical line into deter-
2. Clean or replace filter/detergent
line.
3. Push nozzle forward for
low pressure mode.
4. Open chemical adjuster.
Contact Generac service facility.
1. Fill crankcase to proper level.
2. Clean or replace air cleaner.
3. Fill fuel tank.
4. Drain gas tank; fill with fresh fuel. O
MN
SHOOTING В
а
«#7 f
SS
| TROUBLE Generac6000CP High Pressure Washer
a TROUBLESHOOTING POINTS
PROBLEM
Engine shuts down during operation
Engine lacks power.
Engine “hunts” or falters.
CAUSE
5. Spark plug wire not connected
to spark plug
6.Bad spark plug.
7. Water in gasoline.
8. Overchoking.
9. Excessively rich fuel mixture.
10. Intake valve stuck open or closed.
11.Engine has lost compression.
1. Out of gasoline.
2. Low oil level.
Dirty air filter.
Choke is opened too soon.
until engine runs smoothly.
High Pressure Washer
bn
17
CORRECTION
5. Connect wire to spark plug.
6. Replace spark plug.
7. Drain gas tank; fill with fresh fuel.
8. Open choke fully and crank
engine.
9. Contact Generac service facility.
10. Contact Generac service facility.
11. Contact Generac service facility.
1. Fill fuel tank.
2. Fill crankcase to proper level.
Replace air filter.
Move choke to halfway position
O.
7 Generac 6000CP High Pressure Washer
7
Drawing No. 99914 O -
EXPLODED VIEW — PRESSURE WASHER
а
>
Ÿ
Lr
в
ti
00 >
>
INIONJ E
og Generac 6000CP High Pressure Washer
я
) O Y a Drawing No. 99914
, REPAIR PARTS — PRESSURE WASHER
ITEM PART NO. QTY. DESCRIPTION
s 1 40945 9 M6-1 x 20 Socket Head Capscrew
2 93873 9 M6 Ribbed Lock Washer
3 95212A 1 Unloader Assembly
4 22246 2 Lock Washer
5 93871 1 Engine Adaptor Gasket
6 93723 1 2.0 x 25 x 2.6 O-Ring
7 99749A 1 1500 - 2000 Pump Assembly
8 95454 1 Oil Breather Fill Cap
9 94994A 1 1 Gallon Fuel Tank
10 96001 4 M6-1.0 x 21 Shoulder Bolt
1 31669 2 1/4"-20 x 1-3/4” Carriage Bolt
12 96002 4 Tank Bushing
13 95549 1 Fuel Cap
14 48031C 4 Hose Clamp
15 30340 1 1/4" |.D. Fuel Hose
16 96193 1 Fuel Shut-Off Valve
17 95214 1 220 Fuel Tank Cradle
19 52857 2 M6-1.0 Locking Nut
20 83512 2 M8-1.25 x 15mm Taptite
22 94944 3 Pivot Piston Shoe
23 52858 10 M8 Locking Hex Nut
24 98539E 1 1.30 Dia. Nozzle Head
25 88688 1 Muffler Assembly
26 93790 i 114 x 119 x 2.6 O-Ring
27 98696 1 Handle
28 89476 { Exhaust Gasket
29 40976 2 M8 x 20 Socket Head Capscrew
30 49808 2 M12 Flat Washer
31 88521 2 10” Dia. x 4" Wide Wheel
32 39414 4 M8 x 35 Hex Head Capscrew
35 87841 2 Vibration Mount
36 30253 6 M8 x 20 Hex Head Capscrew
37 97178 2 Knob Handle
38 96414 1 Important Decal
40 93728A 2 Pin-Wheel Axle
41 96415 1 Caution Decal (English)
43 964307 1 Anodized Engine Adaptor
44 99731 1 1.30 Dia. Replacement Nozzle
46 89634A 1 50 Ft. Hose
47 97633 1 Gun
48 95441 1 Engine Spacer
49 87815 2 Safety Goggles
50 96963 1 Mounting Base
51 96168 1 Injection Hose Assembly
52 98698A 1 Tube Support Assembly - R.H.
53 986988 1 Tube Support Assembly - L.H.
54 25391 2 Jam Nut
55 ENG20183 1 Generac Engine
56 75402 2 1/2” Dia. Push Nut
, 57 96302 1 Logo Decal
58 96542 1 Roller Thrust Bearing
59 97673V 1 8mm Axial Cam Lift
60 94738 1 Belleville Washer
61 23707 4 5/16"-24 x 1" Socket Head Capscrew
62 92479 4 M8 Ribbed Lock Washer
63 93887 1 Jam Nut
64 95165 1 Engine Shaft-Taper Adaptor
65 97606 1 Roller Thrust Bearing15.5
High Pressure Washer
"SS
19
O, Generac 6000CP High Pressure Washer
7
7
©
LÉ
8 0%
Drawing No. 90288
oF
NZ
U
O
hr
CA
‚U .
pa
oO
—
=
—
>
Oo
TT
m
O
—_
Qo.
><
fr
High Pressure
20
E Generac 6000CP High Pressure Washer
es
Drawing No. 90288
REPAIR PARTS — LONG BLOCK
ITEM DESCRIPTION PART NO. QTY.
1 Connecting Rod w/Cap 76380 1
2 Piston Pin 76389 1
3 Piston Ring Set 78660 1
5 1/8" NPFT Pipe Plug 72683 1
6 Piston 90325 1
7 Piston Pin Retainer 76390 2
8 Crankshaft Assm. w/Gear (Generac Straight Shaft) 83338 1
Crankshaft Assm. w/Gear (Universal Taper) 83337 1
Crankshaft Assm. w/ Gear (SAE Straight Shaft) 83339 1
9 Governor Arm “R” Pin 78658 1
10 Governor Arm 76354 1
11 Crankcase Sub-Assembly 89213B 1
12 Sleeve Bearing 76349 1
13 Crankshaft Seal 81695 2
14 Governor Gear Assembly 76359 1
15 Governor Retainer (“C” Ring) 78645 1
16 Governor Spool 76365 1
17 Sleeve Dowel © 12 78699B 3
18 Camshaft Assembly 83335 1
19 Crankcase Gasket 89096 1
21 Cylinder Head Gasket 88058 1
22 Oil Pressure Spring Retainer 78691 1
23 Oil Pressure Sprin 76367 1
24 Pressure relief Bal 76362 1
25 M5-0.80 x 8mm Screw 78692 1
26 M6-1.00 x 12mm Pan Head Screw & Lock Washer 78606 4
27 Thrust Washer 76361 1
28 Flanged Hex Head Capscrew 89230 6
29 Gear Cover Sub-Assembly 89665A 1
30 Valve Spring Retainer 86293 2
31 Valve Spring 88401 2
32 12 Dia. x 20 Long Dowel Pin 88590 1
33 Inner Gerotor 83152 1
34 Connecting Rod Bolt 76381 2
35 Governor Arm Washer 78659 1
36 Cylinder Head w/Valve Seats & Guides 884048 1
37 Exhaust Valve 90082 1
38 Intake Valve 90081 1
39 Push Rod 88396A 2
40 Tappet 83235 2
41 Oil Pick-up Assembly 80336 1
42 Rocker Cover Gasket 88397 1
43 Pivot Ball Stud 77161 2
44 Rocker Arm 77160 2
45 Rocker Arm Jam Nut 76307 2
46 Push Rod Guide Plate 88403 1
47 M8 x 50mm Head Bolt 77168 5
48 Rocker Cover Breather Assembly 88412 1
49 Oil Fill Plug 76329 1
50 1/4" NPT Pipe Plug 72657 2
51 Outer Gerotor - 6/5 83153 1
52 O-Ring 17.8 1.0. x 2.4 Thick 86254 1
53 Valve Spring Washer 84186 2
54 Valve Stem Seal 88156 1
57 Serial No. Decal 20527 1
58 Wave Washer 99922 1
High Pressure Washer
EE
21
© Generac 6000CP High Pressure Washer
7
р
сч
O
©
©
o
O
<>
о
£
>
©
|
O
u
«=>
e
——
I
=
Li
|
su
Q
UU
=
=
|
LJ
<=
U
P=
SE
|
=
—
=>
(a)
(WW
a
e
=}
o
><
LL]
SSVd-AS
yalNiTO 67
auvanvis /
9%
(TY UIdS)
ZLIHM 3 MOVIE
NMOG-LNHS 110 MOT HAM
WILSAS NOLLINOI TYNOLLdO
Y 6 Y
N33yYo xa AN |
9%
ty
7
Ti
И
€ mm
AVIS
№3349 ‘LT
19
——Gt
WILSAS
NOILINDI QYVONVLS
High Pressure Washer
22
› @
9,
A
DESCRIPTION
Generac 6000CP High Pressure Washer
¡TEM PART NO. QTY.
1 GN220 Long Block Taper Shaft 90508 1
GN191 Long Block Taper Shaft 90507 1
GN191 Long Blk Straight Shaft 90991H 1
GN220 Long Blk Straight Shaft 99095H 1
GN220 Long Blk Water Pump 92567 1
2 Flywh! Assm. 28 Deg.
Timing GN220 77182E 1
Fiywhl Assm. 34 Deg. Timing
GN191 77812T 1
3 Ignition Coil Assembly 81675 1
4 M16 x 1.5 Hex Nut 81810 1
5 Conical Washer 83312 1
6 Blower Housing 90695A 1
7 Carb. - GN191HS-50Hz,
GN220HS-50Hz Press. Washers 95948 1
Carb. - GN191HS-60Hz 98469 1
Carb. - GN220HS-60Hz 97747 1
8 Carb./Manifold Gasket 78631 1
9 Intake HS Manifold 90948 1
10 Air Cleaner Cover 78608 1
Opt. Air Cleaner Cover (Plain) 78608A 1
1" Air Filter Element 78601 1
12 Air Filter Pre-Cleaner 78602 1
13 Recoil Cup 83015 1
14 Recoil Assembly 95268 1
15 Manifold Head Gasket 90051 1
16 Carb./Air Cleaner Gasket 91846 1
17 Air Cleaner Cover Bolt 78609 2
18 Breather Hose 90947 1
19 4 x 19 Woodruff Key 82774 1
20 Governor Lever Assembly 86962 1
21 60Hz Governor Spring 78604 1
50Hz Governor Spring 86634 1
22 Governor Adjusting Screw 83502 1
24 Idle Control Coil 83782 1
25 Anti-Lash Extension Spring 86037 1
26 Governor Rod 86384 1
27 Governor Adjust Bracket 83781 1
28 Carb. Mounting Bolt 78643 2
29 M5-0.8 Metal Lock Nut 83503 1
30 Lower Wrapper 89739 1
Drawing No. 90692
REPAIR PARTS — ENGINE TRIM SPECIFICATIONS
High Pressure Washer
>“
23
ITEM DESCRIPTION PART NO. QTY.
31 Air Cleaner Base (with nuts) 78607 1
32 Blower Housing Back Plate 78651C 1
33 Top Assembly Wrapper 92984 1
34 Breather Canal Cover 80303 1
35 Champion RC12YC Spark Plug 72347 1
36 M6-1 x 10 Taptite Bolt 45756 5
37 M6-1 x 12 H Hd. w/Lockwasher
Screw 66476 11
38 M6-1 x 30 Flanged H Hd.
w/Lockwshr Screw 80316 2
39 #8 x .37" Plastite Screw 59635 1
40 Choke Lever Knob 83504 1
43 M6-1 x 30 Taptite Bolt 82981 2
44 Shut-off Switch 78653 1
46 M6 Lock Washer 22097 1
47 M8 x 15 Taptite Bolt 83512 1
48 LED Low Oil Ind. Light Assm. 85272 1
LED Low Qil Indicator Light Assm.
(Used w/ Opt. LOS Module) 86753 1
49 4 psi Oil Pressure Switch 77667 1
50 Ground Wire Assembly 002-85271 1
51 L.O.S., S Eng. Decal 84195 1
52 Wire Assembly Ignition 001-85271 1
54 #3 Sleeving BLk 85620 1
55 3 Pin Male Housing 84329 1
56 Carb. Wear Washer 85953 1
57 Oil Filter Pad Gasket 91848 1
58 M6 x 1.0 x 20 Taptite 92978 2
59 Oil Filter Adaptor (MC Series) 84982 1
60 Oil Filter (Optional) 70185 1
61 LOS Module (Optional) 87221A 1
62 By-Pass Adaptor (Optional) 88758 1
63 Oil Fill Tube (Optional) 91041 1
64 36/64 Expansion Plug 94820 1
65 Oil Fill Gasket 91230 1
66 M6 x 12 Taptite 90388 1
67 Oil Fill Dipstick (Optional) 91475 1
68 M8-1.25 Hex Jam Nut 66311 1
69 M6-12.5 O.D. Flat Washer 49811 1
70 Fuel Tank Bracket (Optional) 95213 1
ta
Drawing No. 20960
E Generac 6000CP High Pressure Washer
$
92
>
SE Nr ualva
100 HILYA Ev
High Pressure Washer
pra
24
La
21
<
>
39nv9--¿6146 ©! rd
¡ IYNOJIIdO |! < “LavHS HAdVL
EXPLODED VIEW — PUMP
Generac 6000CP High Pressure Washer
y
©
«>
©
) O E Drawing No. 20960
| REPAIR PARTS — PUMP
ITEM DESCRIPTION PART NO. QTY. ITEM DESCRIPTION PART NO. QTY.
1 Engine Adaptor Gasket 93871 1 39 M8-1.25x.75 Stra. Shft. Screw 93874 6
2 Engine Adaptor 964032 1 40 Unloader Assem. Spindle 95373 1
3 Ball Thrust Bearing 96452 2 41 Unloader Pistion Guide 95367 1
4 Check Valve Poppet 97215 6 42 1.78 x 14 O-Ring 95372 1
5 Eng. Taper Shaft Adapt. 95165 1 43 Chem. Injector Fitting 95378 1
6 3GPM Axial CAM 97673V 1 44 High Press. Outlet Adaptor 95377 1
7 Ball Thrust Bearing 97606 1 45 1.78 x 12.4 O-Ring 93788 1
8 114 x 119 x 2.6 O-Ring 93790 1 46 1.78 x 15.6 O-Ring 93787 1
9 Piston Spring Retainer 95386 3 47 7.51.D. x 0.6 Dia. x 11.5 Spring95376 1
10 Straight Shaft Piston 95217 3 48 High Press. Outlet Piston 95374 1
11 Piston Return Spring 96400 3 49 #2.4 x 4.3 O-Ring 95375 1
12 M8 Ribbed Lockwasher 92479 10 50 Press. Adjust Spring 95365 1
13 M6 Ribbed Lockwasher 93873 9 51 Press. Adjust w/Groove Adapt 95364A 1
14 M6x1x20 Socket Hd. Screw 40945 9 52 Black Press. Adjust Handle 95381A 1
15 Aluminum Crankcase 97568 Y 1 53 1/8 NPT Pipe Plug 96137 1
16 Qil-Piston Seal 93680 3 54 2.6 x 20.2 O-Ring 93723 1
17 Pilot Spacer 93668 3 55 Press. Relief Valve Body 95216 1
18 Lo-Pres "U” Pak Seal 93667 3 56 8.3x11x1.24 Back-Up O-Ring 95369 1
19 Bearing Seal Ring 96015 3 57 Unloader Piston 95368 1
20 Oi Fill Breather 95454 1 58 #1.78 x 7.65 O-Ring 95370 1
21 High Press. Por Tower 97027 3 59 Spring Support 95363 1
22 High Press. Red Seal 96052 3 60 O-Ring 96069 3
23 Back-Up Ring 95504 6 61 Back-Up Ring 95506 3
24 2.62 x 17.12 O-Ring 95503 6 64 Piston Support 95371 1
25 Check Valve Kit 97128 6 65 Chem. Injection Spring 95380 1
26 Check Valve Seat Support 97028 6 66 Belleville Washer 16 x 2.7 94378 1
27 5/16-24x1 Socket Head Bolt 23707 4 67 M16-1.5 Jam Nut 93887 1
28 Thermal Bypass Spring 93652 1 68 M18 x 1.0 Nut 95366 1
29 Bypass Piston 95416 1 69 Engine Pilot Spacer 95441 1
30 Spacer Plate 97122V 1 71 Piston Pivot Shoe 94944 3
33 Head Gasket 93645 1 72 “C"” Retainer Ring 94284 3
34 Thermal Bypass Actuator 93644 1 73 1.78 x 2.90 I.D. O-Ring 93876 1
35 Garden Hose Connector 95320 1 74 #5.56 (7/32”) Ball 95379 1
36 Aluminum Cylinder Head 1971207 1 75 1.78 x 6.07 O-Ring 93656 1
37 Spindle Seat 95382 1 76 1.24 x 6.7 Back-Up Ring 93657 1
38 1.78 x 17.2 O-Ring 93722 2 77 Unloader Assembly 95212A 1
High Pressure Washer
RL
25
oF Generac 6000CP High Pressure Washer
©
$
Drawing No. 81671 0 SL
REPAIR PARTS — RECOIL STARTER ASSEMBLY
ITEM DESCRIPTION PART NO. QTY.
1 Rewind Starter Housing 100-81671 1 .
2 Brake Spring 105-81671 1
3 Dog Spring 103-81671 2
4 Starter Dog 104-81671 2 ;
5 Retainer Pawl 109-81671 1
6 Retainer Pawl Screw 106-81671 1
9 Pulley 102-81671 1
10 Spring and Keeper 101-81671 1
11 Handle Insert 108-81671 1
12 Starter Rope with Handle 107-81671 1
13 Rope (included with Item 12) e 1
High Pressure Washer
as a
26
o> Generac 6000CP High Pressure Washer
&
‚eo °
|
7
я
LIMITED PRESSURE WASHER WARRANTIES (includes “Master Contractor”)
GENERAC warrants to the original retail purchaser, the pressure washer manufactured by GENERAC to be free from defects in mate-
rial and workmanship for the period(s) set forth below from the date of original purchase. This warranty is not transferable. The term
‘original purchaser” means the person for whom the pressure washer is originally purchased.
Warranty Schedules
Electric Power Washer 1 year (does not apply to commercial or rental operations)
CONSUMER" COMMERCIAL"
Generac GN-Series Engine-driven Engine: 2 years 1 year
Power Washer (2nd year parts only)
Pump: 1 year 90 days
All Other Engine-driven Engine: Warranted solely by Warranted solely by
Power Washers Engine Manufacturer Engine Manufacturer
Pump: 1 year 90 days
* NOTE: For the purpose of this warranty “consumer use” means personal residential household use by original purchaser.
“Commercial Use” means all other uses, including rental, construction, commercial and income producing purposes. Once
a pressure washer has experienced commercial use, it shall thereafter be considered a commercial use pressure washer for
the purposes of this warranty.
During said warranty period, GENERAC will, at its option, repair or replace any part which, upon examination by GENERAC or GEN-
ERAC Authorized Dealers, is found to be defective under normal use and service"*. All transportation costs under warranty, including
return to the factory if necessary, are to be borne by the purchaser and prepaid by the purchaser.
** NORMAL WEAR: As with all mechanical devices, the GN-Series engines need periodic parts service and replacement to
peform well. This warranty will not cover repair when normal use has exhausted the life of a part or an engine.
THIS WARRANTY DOES NOT INCLUDE: Used products and demonstration equipment. Parts such as GUNS, HOSES, WANDS,
NOZZLES or other wear items such as quick couplers, oil, gauges, belts, O-rings, filters, pump packing, etc. Pumps which have been
run without water supplied. Damage or malfunctions resulting from: accidents, abuse, modifications, alterations, or improper servic-
ing. Freezing or chemical deterioration. Normal maintenance such as adjustments, fuel system cleaning and obstruction (due to chemical,
dirt, carbon or lime, etc.).
THIS WARRANTY 1S IN PLACE OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, SPECIFICALLY, GENERAC MAKES NO
OTHER WARRANTIES AS TO MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. The duration of any implied war-
ranties which cannot be disclaimed is limited to the time period as specified in the express warranty. LIABILITY FOR CONSEQUENTIAL,
INCIDENTAL, OR SPECIAL DAMAGES UNDER ANY AND ALL WARRANTIES IS EXCLUDED, EVEN IF SUCH DAMAGES ARE A
DIRECT RESULT OF GENERAC's NEGLIGENCE. Some states do not allow limitations on how long an implied warranty lasts, or the
exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you. This war-
ranty gives you specific legal rights and you may also have other rights, which vary from state to state.
For service, see your nearest GENERAC authorized warranty service facility or call 1-800-333-1322. Warranty service can be per-
formed only by a GENERAC authorized service facility. This warranty will not apply to service at any other facility. Atthe time of requesting
warranty service, evidence of original purchase date must be presented.
GENERAC CORPORATION P.O. Box 8 Waukesha, W1 53187
TELEPHONE: (414) 544-4811 FAX: (414) 544-4851