Simplicity 00776-1 Operator's Manual

GENERAC
The Reliable Ones
1300PSI
Double Insulated
Electric High Pressure Washer
Owner’s Manual
P
CU RES
ST SU
O R
HO
UR 1-8 ME E W
S:
A
0 R
Mo 0-2 HE SH
n.- 70
E
L
Fri
-1 PLI R
(C . 8 a 40
N
E
ST
.m 8
)
. to
5p
.m
.
Model No. 0776-1 (1.5 gpm High Pressure Washer) Manual No. B1742 Revision 0 (7/17/97)
This symbol points out important safety instructions, which, if not followed, could endanger the personal safety
and/or property of yourself and others. Read and follow all instructions in thE manual before attempting to operate
this unit.
C
A
Generac 1300PSI Electric High Pressure Washer
R
E
N
E
G
IMPORTANT! — SAFETY INSTRUCTIONS — IMPORTANT!
Save these instructions
DANGER!
DANGER!
Risk of electrocution!
Risk of Explosion — Do not spray flammable liquids.
•
•
•
•
•
• Never aim the gun at people, animals or plants.
• For household use. For indoor or outdoor use.
• High pressure stream of fluid that this equipment can produce may pierce skin
and its underlying tissues, leading to serious injury and possible amputation.
• High pressure spray can cause paint chips or other particles to become airborne
and fly at high speeds.
• Always wear eye protection when you use this equipment or when you are in vicinity where the equipment is in use.
• Never move the machine by pulling on high pressure hose. Use the handle provided on the top of the unit.
• Use a respirator or mask whenever there is a chance that vapors may be inhaled.
Read all instructions with the mask so you are certain the mask will provide the
necessary protection against inhaling harmful vapors.
• High pressure spray may damage fragile items including glass. Do not point spray
gun at glass when in the high pressure mode.
• Keep the hose connected to machine or the spray gun while the system is pressurized. Disconnecting the hose while the unit is pressurized is dangerous.
• Hold the spray gun firmly in your hand before you start the unit. Do not leave the
pressure washer unattended while the machine is turned on.
• Cleaning area should have adequate slopes and drainage to reduce possibility
of a fall due to slippery surfaces.
• Keep water spray away from electric wiring or fatal electric shock may result.
• Do not by-pass any safety device on this machine.
• Operate and store this unit on a stable surface.
• Inspect hose each time before using it. Check all hoses for cuts, leaks, abrasions,
bulging of cover, damage or movement of couplings. If any of these conditions
exist, replace hose immediately. Never repair high pressure hose. Replace it with
another hose that meets minimum pressure rating of your pressure washer.
• Store in a clean, dry area. Ideally, the unit should be stored in a frost-free room.
Inspect cord before every use. Do not use if cord is damaged.
Keep all connections dry and off the ground.
Do not touch plug with wet hands.
Double-insulated — When servicing, use only identical replacement parts.
This product shall only be connected to a power supply receptacle protected by
a Ground Fault Circuit Interrupter (GFCI).
• Read instruction manual before using.
CAUTION!
When using this product, basic precautions should always be followed, including the following:
• To reduce the risk of injury, read all instructions before using the product.
WARNING!
To reduce the risk of injury, close supervision is necessary when
product is used near children.
• Know how to stop the product and bleed the pressure quickly. Be thoroughly familiar with controls.
• Stay alert. Watch what you are doing.
• Do not operate the product when fatigued or under the influence of alcohol or drugs.
• Keep operating area clear of all persons.
WARNING!
Risk of injury or injection to persons – Do not discharge stream at persons or animals.
SERVICING OF A DOUBLE-INSULATED PRODUCT
In a double-insulated product, two systems of insulation are provided instead of
grounding. No means of grounding is provided on a double-insulated product, nor
should a means for grounding be added.
• High pressure hose can develop leaks from wear, kinking, abuse, etc. Water
spraying from a leak is capable of injecting material into skin. Do not point the
pressure washer spray at people or animals.
• Do not overreach or stand on unstable support. Keep good footing and balance
at all times.
• Follow the maintenance instructions specified in the manual.
• This product shall only be connected to a power supply receptacle protected by
a Ground Fault Circuit Interrupter (GFCI). This is done to comply with National
Electrical Code (NFPA 70) and to provide additional protection from risk of electrical shock.
• Save these instructions.
• Operate this pressure washer only in areas away from combustible materials, combustible fumes or dust.
• Some chemicals or detergents may be harmful if inhaled or ingested, causing severe
nausea, fainting or poisoning. The harmful elements may cause property damage
or severe injury.
• Do not allow CHILDREN to operate the Pressure Washer at any time.
• Before starting the Pressure Washer in cold weather, check all parts of the equipment and be sure ice has not formed.
• Units with broken or missing parts, or without protective housing or covers should
NEVER be operated.
Servicing a double-insulated product requires extreme care and knowledge of the
system and should be done only by qualified service personnel. Replacement parts
for a double-insulated product must be identical to the parts they replace. use only
genuine replacement parts. A double-insulated product is marked with the words
“DOUBLE INSULATION” or “DOUBLE INSULATED”.
The symbol
may also be marked on the product.
EXTENSION CORDS
Use only extension cords that are approved for outside use. These extension cords
are identified by a marking “ACCEPTABLE FOR USE WITH OUTDOOR APPLIANCES; STORE INDOORS WHILE NOT IN USE.” Use only extension cords having
an electrical rating not less than the rating of the product. Do not use damaged extension cords. Examine extension cord before using and replace if damaged. Do not
abuse extension cord and do not yank on any cord to disconnect it. Keep cord away
from heat and sharp edges. Always disconnect the extension cord from the receptacle before disconnecting the pressure washer from the extension cord.
2
C
A
Generac 1300PSI Electric High Pressure Washer
R
E
N
E
G
PRODUCT SPECIFICATIONS
CONGRATULATIONS on your purchase of a GENERAC
electric high pressure washer. It has been designed, engineered and manufactured to give you the best possible
dependability and performance.
PRESSURE WASHER SPECIFICATIONS
Should you experience any problem you cannot easily
remedy, please contact your nearest GENERAC Authorized
Service facility, or call the 1–800–270–1408 number listed
on the front of this manual. We have competent, welltrained technicians and the proper tools to service or repair
this unit.
Please read and retain this manual. The instructions will
enable you to assemble and maintain your high pressure
washer properly. Always observe the “SAFETY RULES.”
Model
Number
0776-1
Serial
Number_________________________________
Date of
Purchase________________________________
The model and serial numbers will be found on a decal
attached to the pressure washer. You should record both
serial number and date of purchase and keep in a safe place
for future reference
CUSTOMER RESPONSIBILITIES
• Read and observe the safety rules.
• Follow regular schedule in maintaining, caring for and using
your high pressure washer.
• Follow the instructions under “Maintenance” and “Storage”
sections of this Owner's Manual.
3
Pressure
1300 psi
Flow Rate
1.5 GPM
Detergent Mix
Use undiluted detergent
Water Supply
Temperature
Cold water not to
exceed 104°F
Motor
Brush type (universal)
Rated Voltage
120 volts
Current
14 amperes
C
A
Generac 1300PSI Electric High Pressure Washer
R
E
N
E
G
PACKAGE
CONTENTS OF PACKAGE
Spray Gun*
Nozzle Cleaning Kit**
High Pressure Washer
Nozzle Extension*
Quick-Connect**
High Pressure Hose*
Accessories
Adapter**
Foamer*
* These parts are found separately in the parts box within the package.
** These parts are found separately in the parts bag within the parts box.
4
Goggles*
C
A
Generac 1300PSI Electric High Pressure Washer
R
E
N
E
G
Read this owner’s manual before operating your high pressure washer. Compare the illustrations with your high pressure
washer to familiarize yourself with the locations of various controls and adjustments. Save this manual for future reference.
Spray Gun
Master On/Off Switch
Grip Start™ System
High Pressure Outlet
Nozzle Extension
Foamer
Water Inlet
Safety Flow™ System
Quick–Connect
Foamer — Used to apply detergent. Mixes water and detergent in outlet water flow.
Spray Gun — Controls the application of water onto
cleaning surface with trigger device. Includes safety
latch.
Accessories Adapter (Not Shown) — This specially designed
connector accommodates the connection of a multipurpose
and rotating brush to the spray gun. Both brushes are sold
separately and are not included with this unit.
High Pressure Outlet — Connection for high
pressure hose.
Master On/Off Switch — This switch ONLY enables
the Grip Start™ system to function.
Water Inlet — Connection for garden hose. (Note: You need
to use the quick–connect to attach the garden hose to the pressure washer)
Quick–Connect — Easy connection for intake water
supply.
Grip Start™ System – Pressing and releasing the
spray gun trigger starts and stops the electric motor
in the pressure washer.
Nozzle Extension — Attaches to spray gun.
Safety Flow™ System – Electric motor will not start
unless water is supplied to the pump.
5
C
A
ASSEMBLY
Generac 1300PSI Electric High Pressure Washer
R
E
N
E
G
Read these instructions and Operator’s Manual in its
entirety before you attempt to assemble or operate your
new high pressure washer. Your high pressure washer has,
for the most part, been assembled at the factory. Before you
can operate your new high pressure washer, you must
properly connect the high pressure hose and the water
supply.
Figure 2 - Attach High Pressure Hose to Main Unit
If you have any problems with the assembly of your pressure washer, please call the pressure washer helpline at
1-800-270-1408.
TO REMOVE PRESSURE WASHER
FROM CARTON
• Remove parts box.
• Remove parts bag from parts box.
• Remove main unit with attached electrical cord.
Refer to Page 4, “Contents of Hardware Pack” for an illustrated listing of all items included with your pressure
washer. Become familiar with each piece before assembling
the pressure washer. Check all contents against the illustrations on Page 4. If any parts are missing, call the pressure
washer helpline at 1-800-270-1408.
• Included with this unit is a quick-connect fitting that you must
attach to the water inlet and your garden hose. You can install
the male connector end by hand but you may need to use
an adjustable wrench to tighten it (Figure 3).
Figure 3 - Install Quick Connect
HOW TO SET UP YOUR
PRESSURE WASHER
• Unwind the high pressure hose and attach it to spray gun
(see Figure 1).
Figure 1 - Attach Hose to Spray Gun
• Check the screen on the female quick–connect. Be sure it is
clean and check for damage. If you see any damage in the
screen, do not use that female quick–connect.
• Attach the female quick connect to your garden hose.
• Attach garden hose to the water inlet using the quick–connect. The quick–connect should lock in place. (Figure 4 on
page 7).
• Attach the high pressure hose to the high pressure outlet
and tighten by hand (Figure 2).
6
C
A
ASSEMBLY
Generac 1300PSI Electric High Pressure Washer
R
E
N
E
G
Figure 4 - Connect Garden Hose to Water Inlet
Figure 5 - Press the Master ON/OFF Switch to the
“ON” position.
WARNING: Gun kicks back. Use both hands.
DANGER: When connecting the unit to a power supply
receptacle, use ONLY a receptacle protected by a
Ground Fault Circuit Interrupter (GFCI). This will help
protect against electrical shock.
DANGER: Risk of injury or injection to people and
animals. DO NOT discharge stream at people or
animals.
• Squeeze trigger to purge pump of system air and impurities.
• Attach nozzle extension to spray gun by aligning the locking
tabs on the extension with the grooves in the gun. Push extension inward and twist clockwise to lock in place (Figure 6).
CAUTION: Before starting you should be sure the
electrical supply is rated at 120 volts, 15 amps.
WARNING: To reduce the risk of electrocution, keep ALL
connections dry and off the ground. DO NOT touch plug
with wet hands.
Figure 6 - Connect the Nozzle Extension to Spray
Gun
• We do not recommend that you use extension cords with
this pressure washer. If, however, your application requires
that you need an extension cord, use only extension cords
that are approved for outside use. These extension cords
are identified by a marking “ACCEPTABLE FOR USE WITH
OUTDOOR APPLIANCES; STORE INDOORS WHILE NOT
IN USE.” Use only extension cords having an electrical
rating not less than the rating of the product. Do not use
damaged extension cords.
• Turn on the water.
NOTE: Water temperature should not exceed 104°F.
• Squeeze trigger to produce spray.
NOTE: Behind the trigger to the gun is a SAFETY LATCH.
You can place this latch as shown in Figure 7 to keep the
washer from accidentally spraying while you are changing
the nozzle head or foamer or performing other tasks.
DANGER: You must attach the spray gun all hoses
before you start the motor.
Figure 7 - Applying the Safety Latch
• Press the master On/Off Switch to the “On” position (Figure 5).
DANGER: You must be careful at this point. Anytime you
squeeze the trigger, the motor will start and water will
spray out of the gun.
CAUTION: Before starting the pressure washer, be sure
you are wearing adequate eye protection. Goggles are
included with this unit.
7
Generac 1300PSI Electric High Pressure Washer
C
A
ASSEMBLY
R
E
N
E
G
STOPPING YOUR PRESSURE
WASHER
• Point the nozzle toward the ground and press the trigger to
test the pattern (Figure. 9).
Figure 9 — Testing the Spray Pattern
• If the pressure washer is running, release the trigger.
DANGER: Releasing the trigger will shut off the motor
but does not shut off the unit. You must also place the
Master On/Off Switch to the “OFF” position.
• Place Master On/Off switch in “OFF” position. Simply shutting
OFF motor will not release pressure in the system. Squeeze
the trigger on the gun to relieve the pressure in the hose.
DANGER: Never leave your pressure washer
unattended even when turned off.
HOW TO USE YOUR WASHER
You now should know how to START your pressure washer
and how to STOP it. The information in this section will tell
you how to adjust the spray pattern and apply detergent or
any other cleaning chemicals.
• For most effective cleaning, keep spray nozzle between 8 to
24 inches of cleaning surface.
• If you get the spray nozzle too close, especially using high pressure mode, you may damage the cleaning surface.
• Do not get closer than 6 inches when cleaning automobile tires.
HOW TO USE ADJUSTABLE
NOZZLE
APPLYING DETERGENT WITH
FOAMER
DANGER: Never adjust spray pattern when spraying.
Never put hands in front of spray nozzle to adjust spray
pattern. You could be injured.
IMPORTANT: Use soaps designed specifically for pressure
washers. Household detergents could damage the pump.
On the end of your spray gun is a nozzle that you can twist
from side to side. With the adjustable nozzle you can adjust
the spray configuration to be either concentrated in a stream
or expanded into a fan pattern.
DANGER: You MUST attach all hoses and the spray gun
before you start the motor.
WARNING: Before removing any spray gun extension,
be sure to turn off the pressure washer and relieve
pressure by pressing the trigger. You could be injured if
you try to remove an extension if the pressure washer is
running and there is pressure in the system.
• Twist nozzle counterclockwise when you wish to produce an
expanded stream. Twist nozzle clockwise to produce a
narrow, concentrated stream (Figure 8).
Figure 8 — Using the Adjustable Nozzle
Pressure washers are useful cleaning tools designed to
clean almost any surface in two easy steps.
Twist Nozzle
Counterclockwise
for Fan Spray
• The first step involves applying an appropriate detergent/solvent solution to penetrate and loosen grime. The detergent
is applied at low pressure to avoid splashing, overspraying
and waste. Leave the solution on surface for 3 to 5 minutes
to allow solution to work.
• The second step involves cleaning the surface you have
prepared with the pressure washer and then rinsing it clean.
Twist Nozzle
Clockwise for
Narrow Spray.
8
C
A
Generac 1300PSI Electric High Pressure Washer
R
E
N
E
G
To apply detergent follow these steps:
NOTE: Never use garden hose inlet to siphon detergent or wax.
• Detach the nozzle extension by pushing in and unlocking it
counterclockwise.
• Remove the bottle from the foamer.
• Align the locking tabs on the foamer with the groves in the
gun. Push inward and twist clockwise to lock in place. (Note:
make sure that the when you lock the foamer into place you
have the hose that connects to the foamer bottle hanging
downward.)
• Prepare your detergent solution as required by your job and
fill bottle with the solution.
• Attach bottle back onto foamer making sure the bottle hangs
down.
• Start washer and apply detergent to a dry surface, starting
from the bottom and working up.
• To rinse, YOU MUST, stop the pressure washer, remove the
foamer and connect the adjustable nozzle extension.
NOTE: Detergents are most effective applied to a dry surface.
The warranty of the high pressure washer does not cover
items that have been subjected to operator abuse or negligence. To receive full value from the warranty, operator
must maintain high pressure washer as instructed in this
manual.
BEFORE EACH USE
DANGER: Water spraying from a leak is capable of
injecting material into skin. Inspect hose each time
before using it. Never repair high pressure hose.
Replace it with another hose that meets minimum
pressure rating of your pressure washer.
CHECK AND CLEAN QUICKCONNECT SCREEN
Remove quick-connect and examine the inlet screen on the
female connector. Clean if clogged or replace the quickconnect inlet screen if damaged.
TO CLEAN
Start at lower portion of area to be washed and work
upward, using long, even overlapping strokes. Detergent or
degreaser works best when you apply it to a dry surface
first. Let it set for 3-5 minutes before washing and rinsing.
CHECK HIGH PRESSURE HOSE
High pressure hose can develop leaks from wear, kinking,
abuse. Check all hoses for cuts, leaks, abrasions or bulging
of cover, or damage or movement of couplings. If any of
these conditions exist, replace hose immediately.
RINSE
Start at the top of area to be rinsed, working down with the
same action as for cleaning.
Figure 10 — Connecting the Foamer
9
C
A
Generac 1300PSI Electric High Pressure Washer
R
E
N
E
G
NOZZLE MAINTENANCE
CHECK GUN AND WAND
Examine hose connection and make sure it is secure. Test
trigger by pressing it and making sure it springs back into
place when released. Put safety latch in ON position and
test trigger. You should not be able to press trigger.
If the nozzle becomes restricted or clogged with foreign materials, such as dirt, excessive pump pressure may develop. A
partially clogged nozzle can cause a pulsing sensation during
use. This generally is not a pump related problem, but rather
a clogged or partially restricted nozzle.
PURGE PUMP OF AIR AND
CONTAMINANTS
If the nozzle becomes clogged or partially restricted, immediately clean the nozzle with the kit included with your pressure
washer by following these instructions:
To remove the air from the pump, follow these steps:
•
•
•
•
•
• Set up the pressure washer as described in the ASSEMBLY
section and connect the water supply.
• Remove the nozzle attachment from the gun.
• Pull the trigger on the gun and hold.
To remove the contaminant from the pump, follow these steps:
• Set up the pressure washer as described in the ASSEMBLY
section, connect the water supply and start the pressure
washer according to instructions in the OPERATION section.
• Remove the nozzle attachment from the gun.
• Pull the trigger on the gun and hold.
• When the water supply is steady and constant, you may
refasten the nozzle attachment and start the pump.
Shut off the washer and turn off the water supply.
Separate the nozzle extension from the gun.
Open the adjustable nozzle to the narrow stream setting.
Remove the nozzle using the allen wrench provided in the kit.
Use the wire included in the kit (Figure 11) or a small paper
clip to free the foreign materials clogging or restricting the
nozzle.
Figure 11 - Loosening Debris in Nozzle
10
C
A
Generac 1300PSI Electric High Pressure Washer
R
E
N
E
G
PREPARING THE UNIT FOR
STORAGE
• Remove additional debris by back flushing water supply through
wand (Figure 12). Back flush between 30 to 60 seconds. Turn
wand to stream spray while flushing.
Water should not remain in the unit for long periods of time.
Sediments of minerals can deposit on pump parts and “freeze”
pump action. If you do not plan to use the Pressure Washer
for more than 30 days, follow this procedure:
Figure 12 - Backwashing the Nozzle
1. Shut off the pressure washer, unplug it and let it cool, then
remove all hoses.
2. Store the pressure washer and its components in such a way
as to protect it from freezing.
5. Store in a clean, dry area. Ideally, the unit should be stored
in a frost-free room.
6. Coil the high pressure hose and inspect it for damage. Cuts
in the hose or fraying of it could result in leaks and loss of
pressure. Should any damage be found, replace the hose.
DO NOT attempt to repair a damaged hose. Replace the
hose with the genuine Generac part.
• Reinstall the nozzle. Do not overtighten.
• Reconnect the wand to the gun.
• Reconnect the water supply, turn on the water, and start the
washer.
• Test the pressure washer by operating with nozzle in narrow
and expanded streams.
7. Drain water from hose and properly store it to prevent cuts
and general wear.
11
C
A
Generac 1300PSI Electric High Pressure Washer
R
E
N
E
G
TROUBLESHOOTING POINTS
PROBLEM
Pressure washer will not start.
CAUSE
CORRECTION
1. No electrical power is available.
1. Check cord, plug power, socket.
and fuse.
2. Motor overheats.
2. Turn off the unit. Press trigger of
gun to relieve.pressure on the
unit. Allow unit to cool for about 2
min. It should run when you turn it
ON again.
Pressure washer does not
come up to pressure.
3. Low voltage.
3. Contact Generac service facility.
4.Trigger not open.
4. Open trigger.
5. Electrical defect.
5. Contact Generac service facility.
1. Pump is sucking air.
1. Water hose must be 1/2-inch
or greater in diameter.
Be sure water supply is ON.
Be sure water supply is clean.
Check all connections for leaks
or blockage.
Turn OFF the unit, hold trigger in
OPEN position to relieve pressure
and allow air in line to escape.
With trigger still in OPEN position
turn ON the unit. Repeat if
necessary.
High pressure spray is irregular.
2. Water inlet is clogged.
2. Clean water inlet screen.
3. Pump not bled to remove air.
3. Switch OFF washer, press trigger,
switch ON washer while pressing
trigger. Repeat if necessary.
4. Pump is faulty.
4. Contact Generac service facility.
1. Nozzle or water supply is restricted.
1. Unplug unit and clean nozzle.
2. Water supply is inadequate.
2. Turn ON water to full position.
12
C
A
Generac 1300PSI Electric High Pressure Washer
R
E
N
E
G
NOTES
13
C
A
Generac 1300PSI Electric High Pressure Washer
R
E
N
E
G
Drawing No. B1744
EXPLODED VIEW — PUMP AND MOTOR
14
C
A
Generac 1300PSI Electric High Pressure Washer
R
E
N
E
G
Drawing No. B1744
PARTS LIST — PUMP AND MOTOR
Item
Part #
Qty.
Description
Item
Part #
Qty.
Description
1
2
3
4
5
6
7
8
9
10
11
12
B1514
97100
21054
21055
20138
20928
20218
20213
21525
B1124
97855
97934
1
1
1
1
1
1
1
1
1
1
1
3
ASSY, Motor Complete
CAP, HP
BOOT, Rubber
GROMMET, Rubber
SWITCH, Auto
HOUSING, Auto-Switch
CAP, Retainer
PISTON ASSY, Auto Switch
WIPER, Piston Bore
CAP, Inlet
“O” RING, dia. 6.5 x 2.01mm
“O” RING, Chk Valve dia. 12.4 x
35
36
37
38
39
40
B1026
76353A
97838
A1111A
97839
97851
1
1
3
1
3
3
13
20212
1
14
15
16
B1565
B1583
A1495
1
1
2
97832
40946
93873
93667
97831
93680
20140
99503
40945
97962
97824A
3
4
7
3
3
3
1
3
3
3
1
19
20
21124
21123
1
1
SPRING, 15.08 x dia. 1.62 CS x
22.3
SEAT, Ball
SCREW, Lock Socket
TAPTITE, M4-0.7x10mm SW
MTG
RING, Backup dia. 4.34 Id x 1.24
“O” RING dia. 3.68 Id x 1.78 CS
41
42
43
44
45
46
47
48
49
50
51
52
97826
1
21
22
21126
21125
1
1
[.070"]
RING, Backup dia. 26.0 ID
“O” RING dia. 25.07 ID x 2.62 CS
53
97825
1
23
24
26
29
31
20217
A1130
97852
28739A
97840
1
1
1
1
3
[.103"]
STOP, Piston Return
SPRING, Pop-off Valve
BALL, dia. 3/16" Pop-off Valve
TIE, Wrap
“O” RING, Hi-press dia. 15.6 x
54
55
56
97716
97829C
97822
1
1
1
CAP, Vinyl
PLUG, Taper dia. 5.4
ASSY., Check Valve, Inlet
PUMP, Head
ASSY., Check Valve, Outlet
“O” RING, Piston dia. 10.82 x
1.78mm
PISTON dia. 15 x 65mm
BOLT, SHCS M6- 1.0 x 35mm
LOCKWASHER, M6 Ribbed
SEAL, Piston “U” Cup
SPACER, Pilot
SEAL, Oil-piston dia. 15 TC4
HOUSING, Piston
SPRING, Piston Return
RETAINER, Piston Spring
BOLT, SHCS M6-1.0 x 20mm
BEARING, Needle dia. 40 x
60mm
WASHER, Brg dia. 40 x 60 x
1mm
WASHER, Brg dia. 36 x 60 x
6mm
CAM, Axial 4.3 MM Stroke
GEAR, Axial Cam
BEARING, Ndle Thrust dia. 35 x
57
20610
1
58
97823
1
32
33
97841
97837
3
1
CAP, Check Valve
“O” RING, Hi-press dia. 9.2 x
59
97834
2
WASHER, Brg dia. 35 x 55 x
3mm
WASHER, Brg dia. 35 x 52 x
1mm
BEARING, Needle dia. 8 x 12 x
34
97835
1
“O” RING, Hsg Seal, dia. 82.2 x
60
97833
1
SHAFT, Idler Axial Cam
.78mm
1.78mm
2.62mm
2.62mm
15
52mm
10mm
C
A
Generac 1300PSI Electric High Pressure Washer
R
E
N
E
G
Drawing No. B1744
EXPLODED
EXPLODED VIEW
VIEW —
— MAIN
XXXXXX...
UNIT
16
C
A
Generac 1300PSI Electric High Pressure Washer
R
E
N
E
G
Drawing No. B1744
PARTS LIST — MAIN UNIT
ITEM
PART #
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
N/A
B1415
A1252
A1313
20566
98806
97893
20984
98801
97892
20985
20986
84543B
98805
84358
99349
B1053
NSP
NSP
21334
21335
21265
96016
A1484
A1485
97835
99350
21336
21337
B1417
21338D
A1069
B1051
87815
98904
B1236D
QTY
1
1
1
1
1
1
1
1
4
1
1
1
2
1
4
1
1
1
1
1
1
1
1
1
1
1
6
1
1
1
1
1
1
1
1
1
DESCRIPTION
ASSY., Motor and Pump (see exp. view B1744 on pages 14 and 15)
DECAL, Circuit
DECAL, Unit
DECAL, Instructions
DECAL, 1-800 #
FOAM, Air In, Fan-end
HOUSING, Switch and Cord
SWITCH, Rocker 16A
MOUNT, Rubber
COVER, Motor
ENCLOSURE, Rocker Switch Boot
BOOT, Rocker Switch
SCREW, 3.5mm x 12mm Plastite
CORD, Power
SCREW, #6-19 x .75 mm Plastite
STRAIN RELIEF, Cord
DECAL, ETL
DECAL, Data
OVERLAMINATE
HOUSING, Inlet
HOUSING, Outlet
QUICK DISCONNECT, Male
QUICK DISCONNECT, Female
NUT, Strain Relief Lock
SEAL RING, Strain Relief
“O” RING, Hsg Seal, dia. 82.2 x 2.62mm
SCREW, #6 Plastite
GUN, Spray
WAND, Extension
HOSE, High Pressure
NOZZLE, Head
FOAMER
ADAPTER, Accessories
GOGGLES
HANG TAG CSA, Nozzle
NOZZLE, 1.15mm dia. (Lilac)
17
C
A
Generac 1300PSI Electric High Pressure Washer
R
E
N
E
G
LIMITED PRESSURE WASHER WARRANTIES (includes “Master Contractor”)
GENERAC warrants to the original retail purchaser, the pressure washer manufactured by GENERAC to be free from defects in material and workmanship for the period(s) set forth below from the date of original purchase. This warranty is not transferable. The term
“original purchaser” means the person for whom the pressure washer is originally purchased.
Warranty Schedules
Electric Power Washer
1 year (does not apply to commercial or rental operations)
CONSUMER*
Generac GN-Series Engine-driven
Power Washer
All Other Engine-driven
Power Washers
COMMERCIAL*
Engine:
2 years
(2nd year parts only)
1 year
Pump:
90 days
1 year
Engine: Warranted solely by
Engine Manufacturer
Warranted solely by
Engine Manufacturer
Pump:
90 days
1 year
* NOTE: For the purpose of this warranty “Consumer Use” means personal residential household use by original purchaser.
“Commercial Use” means all other uses, including rental, construction, commercial and income producing purposes. Once a
pressure washer has experienced commercial use, it shall thereafter be considered a commercial use pressure washer for the
purposes of this warranty.
During said warranty period, GENERAC will, at its option, repair or replace any part which, upon examination by GENERAC or GENERAC Authorized Dealers, is found to be defective under normal use and service**. All transportation costs under warranty, including
return to the factory if necessary, are to be borne by the purchaser and prepaid by the purchaser.
** NORMAL WEAR: As with all mechanical devices, the GN-Series engines need periodic parts service and replacement to
peform well. This warranty will not cover repair when normal use has exhausted the life of a part or an engine.
THIS WARRANTY DOES NOT INCLUDE: Used products and demonstration equipment. Parts such as GUNS, HOSES, WANDS, NOZZLES or other wear items such as quick couplers, oil, gauges, belts, O-rings, filters, pump packing, etc. Pumps which have been run
without water supplied. Damage or malfunctions resulting from: accidents, abuse, modifications, alterations, or improper servicing. Freezing or chemical deterioration. Normal maintenance such as adjustments, fuel system cleaning and obstruction (due to chemical, dirt,
carbon or lime, etc.).
THIS WARRANTY IS IN PLACE OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, SPECIFICALLY, GENERAC MAKES NO
OTHER WARRANTIES AS TO MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. The duration of any implied warranties which cannot be disclaimed is limited to the time period as specified in the express warranty. LIABILITY FOR CONSEQUENTIAL,
INCIDENTAL, OR SPECIAL DAMAGES UNDER ANY AND ALL WARRANTIES IS EXCLUDED, EVEN IF SUCH DAMAGES ARE A
DIRECT RESULT OF GENERAC’s NEGLIGENCE. Some states do not allow limitations on how long an implied warranty lasts, or the
exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights and you may also have other rights, which vary from state to state.
For service, see your nearest GENERAC authorized warranty service facility or call 1-800-333-1322. Warranty service can be performed
only by a GENERAC authorized service facility. This warranty will not apply to service at any other facility. At the time of requesting warranty service, evidence of original purchase date must be presented.
GENERAC CORPORATION