Hoshizaki HS-5427 Instruction Manual

Hoshizaki HS-5427 Instruction Manual
Hoshizaki Prison Kit
HS-5245, HS-5246, HS-5252, HS-5253,
HS-5254, HS-5255, HS-5426, HS-5427
For use with Hoshizaki Ice Machines: KM-350M_J, KM-520M_J, KM-660M_J,
KM-901M_J, KM-1301S_J/3, and KM-1900S_J/3
Check to ensure that all parts are included:
Index
No. Description
1
Front Panel
2
3
4
5
6
Torx Screw (4 mm-small)
Torx Screw (4 mm-large)
Torx Screw (5 mm)
Torx Pin Bit (small)
Torx Pin Bit (large)
Kit
Number
HS-5426
HS-5427
HS-5245
HS-5246
HS-5252
HS-5253
HS-5254
HS-5255
All
All
All
All
All
Model
KM-350MAJ, KM-520MAJ, KM-660MAJ
KM-350MWJ, KM-520MWJ, KM-520MRJ, KM-660MWJ, KM-660MRJ
KM-901MAJ
KM-901MWJ
KM-1301SAJ/3
KM-1301SWJ/3
KM-1900SAJ/3
KM-1900SWJ/3
All
All
All
All
All
Part
Number
Qty
3B0020G01 1
1A5320G01 1
2A8612G01
1
2A8612G02 1
2A7289G01 1
2A7251-01
1
2A7292G01 1
2A7252-01
1
7PP2I0812 20
7PP2-0410
6
7PP2-0512
3
7PP2-0001
1
7PP2-0002
1
WARNING
• Only qualified service technicians should install this kit to reduce the risk of death, electric shock, serious injury, or fire.
• Move the icemaker control switch to the "OFF" position and turn off the power supply before servicing. Lockout/Tagout to
prevent the power supply from being turned back on inadvertently.
• CHOKING HAZARD: Ensure all components, fasteners, and thumbscrews are securely in place after any maintenance is
done to the appliance. Make sure that none have fallen into the ice storage bin.
• No installation or service should be undertaken until the technician has thoroughly read these instructions.
Installation Instructions
1) Turn off the power supply. Lockout/Tagout to prevent the power supply from being turned on inadvertently.
2) Remove and discard the front panel and screw(s). See Fig. 1 and Fig. 2.
3) Place the new front panel in its correct position and secure with Torx screw(s) (4 mm-large) provided in this kit.
4) Remove all screws from the sides of the appliance (KM-1301 and KM-1900S_J/3) and replace with Torx screws (4 mm-large)
provided in this kit. See Fig. 2.
Model Shown:
Model Shown:
KM-1900SAJ3
KM-520MAJ
Side
4 mm-large
Side
4 mm-large
4 mm-large
Fig. 1
4 mm-large
1
Fig. 2
2A8478-013
5) Remove all but the drain valve fitting screws from the rear of the appliance and replace with Torx screws (4 mm-small) provided in
this kit. See Fig. 3 and Fig. 4.
6) Remove the drain valve fitting screws and replace them with Torx screws (5 mm) provided in this kit.
7) Dispose of any remaining screws.
4 mm-small
4 mm-small
Model Shown:
KM-520MWJ
Drain Valve
Fitting
4 mm-small
5 mm
Fig. 3
4 mm-small
4 mm-small
Model Shown:
KM-1900SWJ3
4 mm-small
4 mm-small
Drain Valve
Fitting
Fig. 4
2
5 mm
2A8478-013
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement