Hoshizaki CR36A Instruction Manual

Hoshizaki CR36A Instruction Manual
Instruction Manual
Steelheart Series
Refrigerated Kitchen Equipment
Models
Refrigerated Equipment Stand
hoshizakiamerica.com
Issued: 5-22-2018
Revised: 10-31-2018
WARNING
Only qualified service technicians should install and service the appliance. To
obtain the name and phone number of your local Hoshizaki Certified Service
Representative, visit www.hoshizaki.com. No installation or service should be
undertaken until the technician has thoroughly read this Instruction Manual.
Likewise, the owner/manager should not proceed to operate the appliance until the
installer has instructed them on its proper operation. Failure to install, operate, and
maintain the appliance in accordance with this manual may adversely affect safety,
performance, component life, and warranty coverage. Proper installation is the
responsibility of the installer. Product failure or property damage due to improper
installation is not covered under warranty.
Hoshizaki provides this manual primarily to assist qualified service technicians in the
installation, maintenance, and service of the appliance.
Should the reader have any questions or concerns which have not been satisfactorily
addressed, please call, send an e-mail message, or write to the Hoshizaki Technical
Support Department for assistance.
Phone: 1-800-233-1940; (770) 487-2331
Fax: 1-800-843-1056; (770) 487-3360
E-mail: techsupport@hoshizaki.com
618 Highway 74 South
Peachtree City, GA 30269
Attn: Hoshizaki Technical Support Department
Web Site: www.hoshizaki.com
NOTE: To expedite assistance, all correspondence/communication MUST include the
following information:
• Model Number
• Serial Number
• Complete and detailed explanation of the problem.
2
IMPORTANT
This manual should be read carefully before the appliance is installed and operated.
Read the warnings and guidelines contained in this manual carefully as they
provide essential information for the continued safe use and maintenance of the
appliance. Retain this manual for any further reference that may be necessary.
CONTENTS
Important Safety Information.................................................................................................. 4
I. Installation Instructions........................................................................................................ 8
A. Location......................................................................................................................... 8
B. Checks Before Installation.............................................................................................. 9
C. Setup.............................................................................................................................. 9
D. Electrical Connection................................................................................................... 10
E. Final Checklist...............................................................................................................11
II. Operating Instructions....................................................................................................... 12
A. Important Notes About Usage...................................................................................... 12
B. Startup......................................................................................................................... 15
C. Controls and Adjustments............................................................................................ 15
1. Temperature Display................................................................................................ 15
2. Adjusting the Temperature Setpoint........................................................................ 16
3. Changing the Temperature Display Scale (°F or °C).............................................. 16
D. Control Module Icons................................................................................................... 16
E. Defrost.......................................................................................................................... 17
F. Alarm Safeties............................................................................................................... 18
G. Food Storage............................................................................................................... 19
H. Safety Devices............................................................................................................. 19
I. Cooling Performance..................................................................................................... 20
J. Cabinet Condensation.................................................................................................. 20
III. Cleaning and Maintenance Instructions........................................................................... 21
A. Cleaning....................................................................................................................... 21
B. Maintenance................................................................................................................. 23
IV. Preparing the Appliance for Periods of Non-Use............................................................. 24
V. Disposal............................................................................................................................ 25
3
Important Safety Information
Throughout this manual, notices appear to bring your attention to situations which could
result in death, serious injury, damage to the appliance, or damage to property.
DANGER
DANGER
WARNING
NOTICE
IMPORTANT
Indicates a hazardous situation that, if not avoided, will result in
death or serious injury.
Indique un risque imminent qui causera la mort ou de graves
blessures, s’il n’est pas évité.
Indicates a hazardous situation that, if not avoided, could result
in death or serious injury.
Indicates a situation that, if not avoided, could result in damage
to the appliance or property.
Indicates important information about the use and care of the
appliance.
Risque De Feu Ou D'Explosion
DANGER
Risk of Fire or Explosion
Flammable Refrigerant Used
• Follow handling instructions carefully
in compliance with U.S. government
regulations.
• Do not use mechanical devices to defrost.
• Do not puncture refrigerant tubing. Risk
of fire or explosion due to puncture
of refrigerant tubing; follow handling
instructions carefully.
• Component parts shall be replaced with like
components.
• Servicing shall be done by factory
authorized service personnel to minimize
the risk of possible ignition due to incorrect
parts or improper service.
• Consult instruction manual/service manual
before attempting to install or service this
product. All safety precautions must be
followed.
• Dispose of properly in accordance with
federal or local regulations.
• Do not place any potential ignition sources
in or near the appliance.
Le Frigorigène Est Inflammable
• Suivre attentivement les instructions
de manipulation conformément à la
réglementation gouvernementale.
• Ne pas utiliser d'appareils mécaniques
pour dégivrer le réfrigérateur.
• Ne pas perforer la tubulure contenant le
frigorigène. Risque de feu ou d'explosion
si la tubulure contenant le frigorigène
est perforée; suivre les instructions de
manutention avec soin.
• Les pièces des composants doivent être
remplacées par des pièces et accessoires
équivalents.
• L’entretien doit être effectué par le
personnel de service autorisé par le
fabricant afin de minimiser les risques
d’inflammation attribuables à l’installation
d’une pièce inadéquate ou à la mauvaise
exécution du service.
• Consulter le manuel du propriétaire/
guide de réparation avant de tenter une
réparation. Toutes les mesures de sécurité
doivent être respectées.
• Éliminer conformément aux règlements
fédéraux ou locaux.
• Ne placez aucune source d’inflammation
potentielle dans ou près de l’appareil.
4
• THE APPLIANCE MUST BE
GROUNDED. The appliance is equipped
with a NEMA 5-15 three‑prong grounding
plug
to reduce the risk of potential
shock hazards. It must be plugged into a
properly grounded, independent 3-prong
wall outlet. If the outlet is a 2-prong outlet,
it is your personal responsibility to have
a qualified electrician replace it with a
properly grounded, independent 3-prong
wall outlet. Do not remove the ground
prong from the power cord and do not
use an adapter plug. Failure to follow
these instructions may result in death,
electric shock, or fire.
• Do not use an extension cord.
• Do not use an appliance with a damaged
power cord. The power cord should not be
altered, jerked, bundled, weighed down,
pinched, or tangled. Such actions could
result in electric shock or fire. To unplug
the appliance, be sure to pull the plug, not
the cord, and do not jerk the cord.
• The GREEN ground wire in the
factory‑installed power cord is connected
to the appliance. If it becomes necessary
to remove or replace the power cord, be
sure to connect the power cord's ground
wire.
WARNING
The appliance should be destined
only to the use for which it has been
expressly conceived. Any other use
should be considered improper and
therefore dangerous. The manufacturer
cannot be held responsible for injury
or damage resulting from improper,
incorrect, and unreasonable use.
Failure to install, operate, and maintain
the appliance in accordance with this
manual will adversely affect safety,
performance, component life, and
warranty coverage.
To reduce the risk of death, electric
shock, serious injury, or fire, follow
basic precautions including the
following:
• Only qualified service technicians
should install and service the appliance.
• Wear appropriate personal protective
equipment (PPE) when servicing the
appliance.
• The appliance must be installed in
accordance with applicable national,
state, and local codes and regulations.
• Appliance is heavy. Use care when
lifting or positioning. Work in pairs when
needed to prevent injury or damage.
Do not lift using the top section or the
drawers.
• To reduce the risk of electric shock, do
not touch the plug with damp hands.
• Unplug the appliance before servicing.
• The appliance requires an independent
power supply of proper capacity.
See the nameplate for electrical
specifications. Failure to use an
independent power supply of proper
capacity can result in a tripped breaker,
blown fuse, damage to existing wiring,
or component failure. This could lead to
heat generation or fire.
• Do not splash, pour, or spray water
directly onto or into the appliance. This
might cause short circuit, electric shock,
corrosion, or failure.
• Do not make any alterations to the
appliance. Alterations could result in
electric shock, injury, fire, or damage to
the appliance.
• The appliance is not intended for use by
persons (including children) with reduced
physical, sensory, or mental capabilities,
or lack of experience and knowledge,
unless they have been given supervision
or instruction concerning use of the
appliance by a person responsible for
their safety.
5
WARNING, continued
• Children should be properly supervised
around the appliance.
• Do not climb, stand, or hang on the
appliance or drawers or allow children or
animals to do so. Do not climb into the
appliance or allow children or animals to
do so. Death or serious injury could occur
or the appliance could be damaged.
• Be careful not to pinch fingers when
opening and closing the drawers or when
handling food pans. Be careful when
opening and closing the drawers when
children are in the area.
• Open and close the drawers with care.
Opening the drawers too quickly or
forcefully may cause injury or damage to
the appliance or surrounding equipment.
• Do not use combustible spray or place
volatile or flammable substances in or
near the appliance. They might catch fire.
• Keep the area around the appliance clean.
Dirt, dust, or insects in the appliance
could cause harm to individuals or
damage to the equipment.
• The appliance is designed only for
temporary storage of food. Employ
sanitary methods. Use for any other
purposes (for example, storage of
chemicals or medical supplies such
as vaccine and serum) could cause
deterioration of stored items.
• A minimum of 4" (11 cm) clearance is
required between the bottom of the
cooking equipment heating element
and the appliance top. When setting up
cooking equipment, follow the cooking
equipment manufacturer's setup
procedure. Temperature at the appliance
top must not exceed 180°F (82°C). For
optimum performance, installation of
a heat shield (supplied by others) is
recommended.
• For cooking equipment on the cabinet, do
not exceed the total maximum weight listed
for your model.
Total Maximum Weight for Cooking
Equipment on the Cabinet
CR36A
700 lb. (318 kg)
CR49A
CR60A
CR72A
1,200 lb. (544 kg)
CR78A
CR85A
CR98A
1,500 lb. (680 kg)
CR110A
• Do not load any single drawer with more
than 75 lb. (34 kg) of product. Depending
on the weight of product in the drawers,
secure the unit as necessary to prevent it
from overturning. Do not open more than
one drawer at a time.
• Do not block air inlets or outlets, otherwise
cooling performance may be reduced.
• Do not tightly pack the cabinet. Allow some
space between items to ensure good air
flow. Also allow space between items and
interior surfaces.
• Food storage and handling must comply
with applicable codes and regulations.
• Do not put warm or hot foods in the cabinet.
Let them cool first, or they will raise the
cabinet temperature and could deteriorate
other foods in the cabinet or overload the
appliance.
• All foods should be wrapped in plastic film
or stored in sealed containers. Otherwise
foods may dry up, pass their smells onto
other foods, cause frost to develop, result
in poor appliance performance, or increase
the likelihood of cross‑contamination.
Certain dressings and food ingredients,
if not stored in sealed containers, may
accelerate corrosion of the evaporator,
resulting in failure.
6
NOTICE
WARNING, continued
• Do not store items near air outlets.
Otherwise, items may freeze up and
crack or break causing a risk of injury or
contamination of other food.
• All casters on the appliance are lockable.
After positioning the appliance in its final
location, lock all casters.
7
• Protect the floor when moving the
appliance to prevent damage to the floor.
• Keep ventilation openings, in the
appliance enclosure or in the built‑in
structure, clear of obstruction. The
factory-installed rear bumpers must be
in place to ensure proper rear clearance.
Blockage of airflow could negatively affect
performance and damage the appliance.
• To prevent deformation or cracks, do not
spray insecticide onto the plastic parts or
let them come into contact with oil.
• To avoid damage to the gasket, use only
the drawer handle when opening and
closing.
• To avoid damage to the top seal, do not lift
the appliance by the top panel or remove
the top panel.
• Do not leave the drawers open.
I. Installation Instructions
WARNING
• The appliance must be installed in accordance with applicable national, state, and
local regulations.
• Appliance is heavy. Use care when lifting or positioning. Work in pairs when needed
to prevent injury or damage. Do not lift using the top section or the drawers.
• Do not tilt the appliance more than 45°.
A. Location
WARNING
• The appliance is not intended for outdoor use.
• Normal operating ambient temperature: 45°F to 100°F (7°C to 38°C)
Operation of the appliance, for extended periods, outside of this normal
temperature range may affect appliance performance.
• The appliance must not be located next to ovens, grills, or other high heat producing
equipment.
• The location must provide a firm and level foundation for the appliance.
• The appliance must not be located in a corrosive environment.
• Minimum Clearance
Top
Side
Rear
WARNING! A minimum of 4" (11 cm) clearance
is required between the bottom of the cooking
equipment heating element and the appliance
top. When setting up cooking equipment, follow
the cooking equipment manufacturer's setup
procedure.
1" (25 mm) The factory-installed rear bumpers
must be in place to ensure proper
rear clearance.
• WARNING! Temperature at the appliance top must not exceed 180°F (82°C).
For optimum performance, installation of a heat shield (supplied by others) is
recommended.
• WARNING! For cooking equipment on the cabinet, do not exceed the total maximum
weight listed for your model.
Total Maximum Weight for Cooking Equipment on the Cabinet
CR36A, CR49A, CR60A CR72A, CR78A, CR85A CR98A, CR110A
700 lb. (318 kg)
1,200 lb. (544 kg)
1,500 lb. (680 kg)
8
B. Checks Before Installation
WARNING
The rating label and nameplate provide electrical and refrigerant data. The rating
label can be seen by removing the front panel. The nameplate is located on the rear
panel. For certification marks, see the nameplate. For electrical connection details,
see "I.D. Electrical Connection." We reserve the right to make specification and
design changes without prior notice.
• Visually inspect the exterior of the shipping package and immediately report any damage
to the carrier. Upon opening the package, any concealed damage should also be
immediately reported to the carrier.
• Remove the shipping carton, tape, and packing material. Also remove the protective
plastic film from both the exterior panels and the interior drawer panel. If the appliance is
exposed to the sun or to heat, remove the film after the appliance cools.
• Remove all accessory containers before discarding the packing materials. Dispose of all
packing materials in a proper and environmentally responsible manner.
• Check for missing or damaged accessories.
C. Setup
1. Remove the Appliance from the Pallet
1) Move as close to the final location as possible.
2) Remove the pallet end board. See Fig. 1.
3) Remove the bolts securing the appliance to the pallet.
4) Secure the drawers so that they will not open during removal from the pallet.
5) While supporting the appliance to keep it from tipping, slide the appliance off of the
pallet and lower the casters to the floor. NOTICE! Do not allow the drawers to bear
the weight of the appliance.
End Board
Drawer
Fig. 1
Bolt
Bolt
2. Check the Refrigeration Circuit
• Visually check that the refrigerant lines do not rub or touch other lines or surfaces and
that the condenser fan blade turns freely.
• Check that the compressor is snug on all mounting pads.
9
3. Position the Appliance and Lock All Casters
All casters on the appliance are lockable. After positioning the appliance in its final
location, lock all casters.
D. Electrical Connection
WARNING
• Electrical connection must meet national, state, and local electrical code
requirements. Failure to meet these code requirements could result in death,
electric shock, serious injury, fire, or severe damage to equipment.
• To reduce the risk of electric shock, do not touch the plug with damp hands.
• The appliance requires an independent power supply of proper capacity. See the
nameplate for electrical specifications. Failure to use an independent power supply
of proper capacity can result in a tripped breaker, blown fuse, damage to existing
wiring, or component failure. This could lead to heat generation or fire.
• THE APPLIANCE MUST BE GROUNDED. The appliance is equipped with a
NEMA 5-15 three‑prong grounding plug
to reduce the risk of potential shock
hazards. It must be plugged into a properly grounded, independent 3-prong wall
outlet. If the outlet is a 2-prong outlet, it is your personal responsibility to have a
qualified electrician replace it with a properly grounded, independent 3-prong wall
outlet. Do not remove the ground prong from the power cord and do not use an
adapter plug. Failure to follow these instructions may result in death, electric shock,
or fire.
• Do not use an extension cord.
• Do not use an appliance with a damaged power cord. The power cord should not
be altered, jerked, bundled, weighed down, pinched, or tangled. Such actions could
result in electric shock or fire. To unplug the appliance, be sure to pull the plug, not
the cord, and do not jerk the cord.
• The GREEN ground wire in the factory-installed power cord is connected to the
appliance. If it becomes necessary to remove or replace the power cord, be sure to
connect the power cord's ground wire.
• Usually an electrical permit and services of a licensed electrician are required.
• The maximum allowable voltage variation is ±10 percent of the nameplate rating.
10
E. Final Checklist
1) Have the appliance and accessories been checked for shipping damage?
2) Is the appliance level? Have all casters been locked?
3) Is the appliance in a site where the ambient temperature is within 45°F to 100°F (7°C to
38°C) all year around?
4) Have the shipping carton, tape, and packing material been removed from the
appliance? Has the protective plastic film been removed from both the exterior panels
and the interior drawer panel?
5) Is there at least 4" (11 cm) clearance between the bottom of the cooking equipment
heating element and the appliance top? Has the cooking equipment been set up per
the cooking equipment manufacturer's setup procedure? Is there at least 1" (25 mm)
clearance at sides? Are the factory-installed rear bumpers in place to ensure proper
rear clearance?
6) Is the temperature at the appliance top 180°F (82°C) or less? Has a heat shield
(supplied by others) been installed?
7) For cooking equipment on the cabinet, is the total weight equal to or less than the total
maximum weight listed for your model?
Total Maximum Weight for Cooking Equipment on the Cabinet
CR36A, CR49A, CR60A CR72A, CR78A, CR85A CR98A, CR110A
700 lb. (318 kg)
1,200 lb. (544 kg)
1,500 lb. (680 kg)
8) Has the power supply voltage been checked or tested against the nameplate rating?
Is the power supply a properly grounded, independent wall outlet? Does the electrical
connection meet all national, state, and local code and regulation requirements?
9) Is the compressor snug on all mounting pads? Have the refrigerant lines been checked
to make sure they do not rub or touch other lines or surfaces? Has the condenser fan
blade been checked to make sure it turns freely?
10) Are all components and fasteners securely in place?
11) Has the end user been given the instruction manual, and instructed on how to operate
the appliance and the importance of the recommended periodic maintenance?
12) Has the end user been given the name and telephone number of an authorized service
agent?
13) Has the warranty card been filled out and forwarded to the factory for warranty
registration?
11
II. Operating Instructions
A. Important Notes About Usage
DANGER
Risk of Fire or Explosion
Flammable Refrigerant Used
• Do not use mechanical devices to defrost.
• Do not puncture refrigerant tubing. Risk of fire or explosion due to puncture of refrigerant
tubing; follow handling instructions carefully.
• Do not place any potential ignition sources in or near the appliance.
Risque De Feu Ou D'Explosion
Le Frigorigène Est Inflammable
• Ne pas utiliser d'appareils mécaniques pour dégivrer le réfrigérateur.
• Ne pas perforer la tubulure contenant le frigorigène. Risque de feu ou d'explosion si la
tubulure contenant le frigorigène est perforée; suivre les instructions de manutention
avec soin.
• Ne placez aucune source d’inflammation potentielle dans ou près de l’appareil.
WARNING
• Only qualified service technicians should install and service the appliance.
• Wear appropriate personal protective equipment (PPE) when servicing the appliance.
• Failure to install, operate, and maintain the appliance in accordance with this manual
may adversely affect safety, performance, component life, and warranty coverage.
• To reduce the risk of electric shock, do not touch the plug with damp hands.
• Do not splash, pour, or spray water directly onto or into the appliance. This might cause
short circuit, electric shock, corrosion, or failure.
• A minimum of 4" (11 cm) clearance is required between the bottom of the cooking
equipment heating element and the appliance top. When setting up cooking equipment,
follow the cooking equipment manufacturer's setup procedure. Temperature at the
appliance top must not exceed 180°F (82°C). For optimum performance, installation of a
heat shield (supplied by others) is recommended.
• For cooking equipment on the cabinet, do not exceed the total maximum weight listed for
your model.
Total Maximum Weight for Cooking Equipment on the Cabinet
CR36A, CR49A, CR60A CR72A, CR78A, CR85A CR98A, CR110A
700 lb. (318 kg)
1,200 lb. (544 kg)
1,500 lb. (680 kg)
• Do not load any single drawer with more than 75 lb. (34 kg) of product. Depending on
the weight of product in the drawers, secure the unit as necessary to prevent it from
overturning. Do not open more than one drawer at a time.
12
• The appliance is not intended for use by persons (including children) with reduced
physical, sensory, or mental capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning use of the appliance by a
person responsible for their safety.
• Children should be properly supervised around the appliance.
• Do not climb, stand, or hang on the appliance or drawers or allow children or animals
to do so. Do not climb into the appliance or allow children or animals to do so. Death or
serious injury could occur or the appliance could be damaged.
• Be careful not to pinch fingers when opening and closing the drawers or when handling
food pans. Be careful when opening and closing the drawers when children are in the
area.
• Open and close the drawers with care. Opening the drawers cover too quickly or
forcefully may cause injury or damage to the appliance or surrounding equipment.
• Do not use combustible spray or place volatile or flammable substances in or near the
appliance. They might catch fire.
• Keep the area around the appliance clean. Dirt, dust, or insects in the appliance could
cause harm to individuals or damage to the equipment.
• The appliance is designed only for storage of food. Employ sanitary methods. Use for any
other purposes (for example, storage of chemicals or medical supplies such as vaccine
and serum) could cause deterioration of stored items.
• Do not block air inlets or outlets, otherwise cooling performance may be reduced.
• Do not tightly pack the cabinet. Allow some space between items to ensure good air flow.
Also allow space between items and interior surfaces.
• Do not put warm or hot foods in the cabinet. Let them cool first, or they will raise the
cabinet temperature and could deteriorate other foods in the cabinet or overload the
appliance.
• All foods should be wrapped in plastic film or stored in sealed containers. Otherwise
foods may dry up, pass their smells onto other foods, cause frost to develop, result in
poor appliance performance, or increase the likelihood of cross‑contamination. Certain
dressings and food ingredients, if not stored in sealed containers, may accelerate
corrosion of the evaporator, resulting in failure.
• Do not store items near air outlets. Otherwise, items may freeze up and crack or break
causing a risk of injury or contamination of other food.
• All casters on the appliance are lockable. After positioning the appliance in its final
location, lock all casters.
13
NOTICE
• Protect the floor when moving the appliance to prevent damage to the floor.
• Keep ventilation openings, in the appliance enclosure or in the built-in structure, clear
of obstruction. Blockage of airflow could negatively affect performance and damage
the appliance.
• To prevent deformation or cracks, do not spray insecticide onto the plastic parts or let
them come into contact with oil.
• To avoid damage to the gasket, use only the drawer handle when opening and
closing.
• To avoid damage to the top seal, do not lift the appliance by the top panel or remove
the top panel.
• Do not leave the drawers open.
14
B. Startup
WARNING
All parts are factory-adjusted. Improper adjustments may adversely affect safety,
performance, component life, and warranty coverage.
Allow the appliance to cool down prior to loading it with food products.
1) Plug the appliance into the electrical outlet. WARNING! To reduce the risk of electric
shock, do not touch the plug with damp hands. At startup, there is a slight delay
before the compressor starts.
C. Controls and Adjustments
1. Temperature Display
The cabinet temperature is displayed on the control module. See Fig. 2. The display
default is °F, but it can be changed to read °C. To change, see "II.C.3. Changing the
Temperature Display Scale (°F or °C)."
Manual
Defrost
Button
Control Module
Up
Button
Compressor Icon
ECO
V
°C
°F
SC
SC
Button
Defrost
Icon
V
Evaporator Fan
Motor Icon
Alarm
Icon
Down
Button
Fig. 2
15
Front Panel
2. Adjusting the Temperature Setpoint
The temperature setpoint is the value for the average cabinet temperature. The
temperature differential for the compressor to turn on and off is ±3°F (±1.7°C) of the
temperature setpoint. For example, for a refrigerator temperature setpoint of 36°F (2°C),
the compressor comes on at 39°F (3.7°C), and the compressor goes off at 33°F (0.3°C).
If necessary, adjust the temperature setpoint temperature as follows:
1) To change the temperature setpoint, press and hold the up button briefly and then
release. The current temperature setpoint appears. Press the up or down button until
the desired value is displayed. After a few seconds, the display returns to the current
cabinet temperature and the temperature setpoint is saved. NOTICE! Do not adjust
the temperature setpoint more than 2°F (1°C) at a time. Allow the temperature to
stabilize for a minimum of 8 hours before making further temperature setpoint
adjustments.
Temperature Setpoint Range Factory Default Temperature Setting
28°F to 45°F (-2°C to 7°C).
33°F (0.5°C)
3. Changing the Temperature Display Scale (°F or °C)
To change the temperature display scale, follow the steps below. The factory default is °F.
1) Press and hold both the up and down buttons for 5 seconds. "PAS" appears briefly in
the display, then "000" appears.
2) Press the up button to change the display to "001".
3) Press the SC button. " EHE" appears in the display. Press the up or down button until
"diS" is displayed.
4) Press the SC button. "CFu" appears in the display. Press the SC button again. The
current temperature display scale setting appears. Press the up or down button to
change the temperature display scale.
5) Press the SC button to save the setting. Wait 1 minute or press the manual defrost
button twice to return to the temperature display.
D. Control Module Icons
Control module icons inform you of energized components and if the appliance is in
alarm.
Control Module Icons
Icon
Meaning
Compressor
Compressor running.
Defrost
Appliance is in defrost cycle. See "II.E. Defrost" for details.
Evaporator Fan Motor (Icon is Applicable to Freezers Only)
Alarm
Appliance is in alarm. See "II.F. Alarm Safeties" for details.
16
E. Defrost
DANGER
Risk of Fire or Explosion Flammable Refrigerant Used
• Do not use mechanical devices to defrost.
• Do not puncture refrigerant tubing. Risk of fire or explosion due to puncture of
refrigerant tubing; follow handling instructions carefully.
Risque De Feu Ou D'Explosion Le Frigorigène Est Inflammable
• Ne pas utiliser d'appareils mécaniques pour dégivrer le réfrigérateur.
• Ne pas perforer la tubulure contenant le frigorigène. Risque de feu ou d'explosion si la
tubulure contenant le frigorigène est perforée; suivre les instructions de manutention
avec soin.
1. Automatic Defrost
Defrost is a time/temperature-initiated, temperature terminated heated defrost.
• Defrost Initiation: When the appliance is plugged in, the 6 hr. defrost timer starts.
Once the 6 hr. defrost timer terminates, the control module checks the defrost
thermistor for defrost initiation temperature of 40°F (4.5°C) or below. If defrost
thermistor is at or below 40°F (4.5°C), defrost initiates. If the defrost thermistor
is not at or below 40°F (4.5°C), the control module continues in cooling mode for
another 2 hours, then the control module checks the defrost thermistor for defrost
initiation temperature of 40°F (4.5°C) or below. If defrost thermistor is at or below
40°F (4.5°C), defrost initiates. If the defrost thermistor is not at or below 40°F
(4.5°C), the control module continues in cooling mode until the termination of the
next 6 hr. defrost timer.
The minimum defrost time is 5 min.
The maximum defrost time is 1 hr.
• Defrost Termination: When the defrost thermistor warms to 41°F (5°C), defrost
terminates and the 6 hr. defrost timer resets.
• The compressor energizes 1-min. after defrost heater de-energizes (drip time)
and the evaporator fan motor(s) energize 2 min. after the compressor energizes.
Note that the 2 min. evaporator fan motor delay time is a maximum; if the defrost
thermistor cools to 36°F (2.2°C) before the 2 min. evaporator fan motor delay timer
terminates, the evaporator fan motor(s) will energize.
• During defrost dEF is displayed. dEF is displayed another 15 min. after defrost
terminates. Once the 15 min. dEF display timer terminates, cabinet temperature
returns to display.
2. Manual Defrost
To initiate a manual defrost, press the manual defrost button.
17
F. Alarm Safeties
Alarm signals are designed to protect the appliance and food product. These alarms
give information or warnings in the event the appliance is operating out of acceptable
parameters. Should one of the alarms occur, follow the instructions in the table below to
address the alarm. The alarm code and alarm icon flash with audible alarm.
Alarm Signals
Alarm Code Problem
E01
Corrective Action/Reset Details
Cabinet Thermistor Malfunction Alarm
Call a qualified service technician.
Cabinet thermistor has failed.
Beeps for 10 seconds, then silent for 50 seconds. To
silence the alarm, press and release the up button.
Appliance cycles 5 min. on, 5 min. off.
E02
Defrost Thermistor Malfunction Alarm
Call a qualified service technician.
Defrost thermistor has failed.
Beeps for 10 seconds, then silent for 50 seconds. To
silence the alarm, press and release the up button.
Appliance cycles on and off with cabinet thermistor.
High Temperature Alarm
Hi
Cabinet temperature has remained
above 57°F (13.9°C) for more than
2 hours.
If obvious corrections such as closing drawers and
cleaning the air filter and/or condenser do not bring
temperature back in range, call a qualified service
technician.
Beeps for 10 seconds, then silent for 50 seconds. To
silence the alarm and clear "Hi" from the display, press
and release the up button. The alarm icon stays on.
Automatically resets when temperature returns to
normal.
Low Temperature Alarm
Lo
Cabinet temperature has remained
below 26°F (-3.3°C) for more than
2 hours.
If obvious corrections do not bring the temperature
back in range, call a qualified service technician.
Beeps for 10 seconds, then silent for 50 seconds. To
silence the alarm and clear "Lo" from the display, press
and release the up button. The alarm icon stays on.
Automatically resets when temperature returns to
normal.
UHi
High Voltage Alarm (135VAC±5% or
more)
Call a qualified service technician.
ULo
Low Voltage Alarm (96VAC±5% or less) The compressor de-energizes if voltage protection
operates. The voltage safeties automatically reset when
voltage is corrected.
18
G. Food Storage
WARNING
• The appliance is designed only for storage of food. Employ sanitary methods. Use
for any other purposes (for example, storage of chemicals or medical supplies
such as vaccine and serum) could cause deterioration of stored items.
• Do not block air inlets or outlets, otherwise cooling performance may be reduced.
• Do not tightly pack the cabinet. Allow some space between items to ensure good
air flow. Also allow space between items and interior surfaces.
• Do not put warm or hot foods in the cabinet. Let them cool first, or they will raise
the cabinet temperature and could deteriorate other foods in the cabinet or
overload the appliance.
• All foods should be wrapped in plastic film or stored in sealed containers. Otherwise
foods may dry up, pass their smells onto other foods, cause frost to develop, result
in poor appliance performance, or increase the likelihood of cross‑contamination.
Certain dressings and food ingredients, if not stored in sealed containers, may
accelerate corrosion of the evaporator, resulting in failure.
• Do not store items near air outlets. Otherwise, items may freeze up and crack or
break causing a risk of injury or contamination of other food.
H. Safety Devices
1. Compressor External or Internal Overload
If combined temperature/amperage value is above the limit specified by the
compressor manufacturer, the compressor overload operates independently to turn
off the compressor. The compressor overload de-energizes the compressor until the
temperature/amperage value returns to an acceptable level.
2. Short-Cycle Protection
There is a 2-minute minimum off-time and on-time for the compressor.
Note: Time may vary with compressor overload or high-pressure switch activation.
3. High-Pressure Switch
If high-side refrigeration pressure exceeds Hoshizaki specifications, the high‑pressure
switch activates and de-energizes the compressor circuit until the refrigeration pressure
returns to an acceptable level.
19
I. Cooling Performance
Be sure the appliance is properly installed and located for optimum cooling performance.
If cooling performance is not at its optimum level, check the following items:
• Drawers opened too often.
• Drawers left open. Close.
• Cabinet too tightly packed or air inlets/outlets blocked. Allow some space between items
to ensure good air flow.
• Warm or hot foods inside. Take them out until they cool down more.
• Ambient temperature too high. Avoid installation near high heat producing equipment or
exposure to direct sunlight.
• Not enough clearance. Ensure a minimum of 4" (11 cm) clearance between the bottom
of the cooking equipment heating element and the appliance top. Ensure cooking
equipment is set up per the cooking equipment manufacturer's setup procedure.
Ensure a minimum of 1" (25 mm) clearance at sides.
• Temperature at the appliance top too high. Ensure the temperature at the appliance top
does not exceed 180°F (82°C). For optimum performance, installation of a heat shield
(supplied by others) is recommended.
• Temperature setpoint not cold enough. Adjust to a colder setting. See "II.C.2. Adjusting
the Temperature Setpoint" for details.
• Appliance in defrost cycle. The cabinet temperature may rise temporarily during the
defrost cycle, but this will not affect the food inside.
J. Cabinet Condensation
In the event condensation develops on the cabinet exterior, check the following items:
• Drawers left open. Close.
• Ambient humidity too high. In high humidity areas it may be necessary to wipe off the
cabinet frame occasionally.
20
III. Cleaning and Maintenance Instructions
A. Cleaning
WARNING
• Unplug the appliance before cleaning to prevent electric shock by unexpected
entrance of water into the appliance or injury by moving parts. To reduce the risk of
electric shock, do not touch the plug with damp hands.
• Before cleaning the appliance, move all foods into another clean refrigerator.
• Before cleaning the appliance, disconnect any cooking equipment on the appliance
top and allow to cool.
• Do not splash, pour, or spray water directly onto or into the appliance. This might
cause short circuit, electric shock, corrosion, or failure.
• Carefully follow instructions provided with cleaning and sanitizing products.
NOTICE
• To prevent damage to the plastic surfaces, do not use the following: hot water,
thinner, benzine, alcohol, petroleum, soap powder, polishing powder, alkaline
cleaner, acid, scouring pad and especially those strong cleaners for use on a
ventilating fan or a cooking range.
• To prevent corrosion and damage to stainless steel surfaces, use only products
formulated for use on stainless steel appliances. Do not use steel wool, abrasive
products, or products containing sodium hypochlorite (chlorine bleach).
• Use a clean cloth for cleaning.
1. Exterior
Wipe the exterior occasionally with a clean, soft cloth. Use a damp cloth containing
a neutral cleaner to wipe off oil or dirt buildup. Clean any rust colored spots using a
non‑abrasive cleanser.
2. Cabinet Interior
Spills should be wiped up promptly to avoid unpleasant odors. The cabinet interior should
be cleaned periodically with a mild soap or detergent and warm water.
3. Drawer Gaskets
Drawer gaskets should be cleaned regularly with mild soap and warm water to remove
dirt and grease.
21
4. Drawers
Drawers and drawer slides are removable.
• To remove a drawer: Remove all items from the drawer. Pull the drawer out to its fully
extended position. Open the safety clips (one on each side) by sliding them forward.
See Fig. 3. Lift up on the handle slightly, then pull to disengage the drawer. Be sure
to support the rear and front of the drawer while removing it. WARNING! Be sure to
close the safety clips when reinstalling the drawer.
• To remove a drawer slide (center slide containing rollers): Open the stop levers
(one on each side) by sliding them to the rear. See Fig. 4. Lift up on the drawer slide
slightly, then pull to disengage the drawer slide. WARNING! Be sure to close the stop
levers when reinstalling the drawer. Drawer slides do not require lubrication, but
drawer slides should be kept clean and free of food.
Note: Drawer slides are dishwasher safe.
Safety Clip
Closed
Stop Lever
Closed
Safety Clip
Open
Stop Lever
Open
Drawer Slide
Stop Lever
Safety Clips
Fig. 3
Fig. 4
22
B. Maintenance
WARNING
• Unplug the appliance before performing maintenance to prevent electric shock or
injury by moving parts. To reduce the risk of electric shock, do not touch the plug
with damp hands.
• Before performing maintenance, move all foods into another clean refrigerator.
• Before performing maintenance, disconnect any cooking equipment on the
appliance top and allow to cool.
1. Condenser
Check the condenser twice a year and use a brush or vacuum cleaner to clean the
condenser as required.
2. Power Supply Connection
If the plug or power cord is damaged, contact your local Hoshizaki service representative
or local Hoshizaki distributor immediately and ask for repairs.
All other maintenance or service on the appliance should be performed in accordance
with the Hoshizaki Service Manual by a qualified service technician.
23
IV. Preparing the Appliance for Periods of Non-Use
When shutting down the appliance for more than one week, follow the instructions below.
WARNING
When preparing the appliance for long storage, prevent the drawers from closing to
reduce the risk of children getting trapped.
NOTICE
When preparing the appliance for long storage, clean the appliance. See "III.A.
Cleaning" for details.
1) Before shutting down the appliance, move all foods into another clean refrigerator.
2) Unplug the appliance. WARNING! To reduce the risk of electric shock, do not touch
the plug with damp hands.
3) WARNING! Prevent the drawers from closing to reduce the risk of children getting
trapped.
24
V. Disposal
DANGER
Risk of Fire or Explosion Flammable Refrigerant Used
• Follow handling instructions carefully in compliance with U.S. government regulations.
• Do not puncture refrigerant tubing. Risk of fire or explosion due to puncture of
refrigerant tubing; follow handling instructions carefully.
• Dispose of properly in accordance with federal or local regulations.
Risque De Feu Ou D'Explosion Le Frigorigène Est Inflammable
• Suivre attentivement les instructions de manipulation conformément à la
réglementation gouvernementale.
• Ne pas perforer la tubulure contenant le frigorigène. Risque de feu ou d'explosion si la
tubulure contenant le frigorigène est perforée; suivre les instructions de manutention
avec soin.
• Éliminer conformément aux règlements fédéraux ou locaux.
WARNING
When preparing the appliance for disposal, remove the drawers to reduce the risk
of children getting trapped.
The appliance contains refrigerant and must be disposed of in accordance with
applicable national, state, and local codes and regulations. Refrigerant must be
recovered by properly certified service personnel.
25
618 Hwy. 74 South, Peachtree City, GA 30269 USA (P) 770.487.2331 (F) 770.487.3360 hoshizakiamerica.com
26
1A5170-012
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement