Epson ET-M3170 Installation Guide
ET-M3170
2
Remove all protective materials from the product.
4
Wait for the ink to fill the tank. Do not squeeze the bottle.
9
Press the power button to turn on the product, then
wait for the power light to stop flashing.
Start Here
IMPORTANT: Before using this product, make sure you read
these instructions and the safety instructions in the online
User’s Guide.
Important Safety Instructions: When using telephone equipment, you
should always follow basic safety precautions to reduce the risk of fire,
electric shock, and personal injury, including the following:
ote: If an error code appears, turn off the product and check
N
that no protective material has been left inside the product.
Caution: Do not touch the flat white cable, translucent film, or
the ink tubes.
3
• Do not use the Epson® product near water.
Note: If ink does not flow from the bottle, lift and reinsert the
bottle.
Close the printer cover.
Caution: After setup, periodically inspect the ink level to ensure
it is not below the lowest line on the tank. Prolonged use when
ink is below the lowest line could damage the product. See the
online User’s Guide for refilling instructions.
Note: Do not connect the power cord yet.
• Always keep this guide handy.
• A
void using a telephone during an electrical storm. There may be a
remote risk of electric shock from lightning.
• Do not use a telephone to report a gas leak in the vicinity of the leak.
Caution: To reduce the risk of fire, use only a No. 26 AWG or larger
telecommunication line cord.
1 Unpack
2
Fill ink tank and charge
the ink
5
10 Select your language, country, time, and date settings on
the LCD screen.
Note: You can change these settings later using the product’s
control panel. For more information, see the online User’s Guide.
11 When the message to see the Start Here sheet appears
on the LCD screen, press and hold the
5 seconds.
hen the ink bottle is empty, remove the bottle and
W
securely close it with the cap.
help button for
Warning: Keep the ink bottle out of the reach of children and do not
drink the ink.
Caution: This product requires careful handling of ink. If ink spills,
wipe it off immediately with a damp towel to avoid permanent stains. If
ink gets on your clothes or belongings, it may not come off.
12 Follow the on-screen instructions to start charging the ink.
Note:
• Epson cannot guarantee the quality or reliability of third-party ink.
• U
se the ink bottle included with the printer to set up the product.
Part of the ink will be used to charge the print head. This bottle may
print fewer pages compared with replacement ink bottles.
1
Ink charging takes approximately 10 minutes. A message
appears when ink charging is complete. Select OK to
continue.
Note: Do not leave the ink bottle inserted; otherwise the bottle
may be damaged or ink may leak.
6
Caution: Do not turn off the product, raise the printer cover, or
load paper while the product is charging or you’ll waste ink.
Close the ink tank cap.
Open the ink tank cover, then open the cap.
Make sure you keep the box shown above for use when
transporting the printer.
Caution: Do not lift the product by gripping the scanner unit. Make
sure you lift using the handholds on the bottom of the product.
Note: After some ink is used for charging, the rest is available
for printing.
Note: Do not open the ink bottle until you are ready to fill the ink tank.
The ink bottle is vacuum packed to maintain reliability.
1
Lift the printer cover until it clicks into place.
7
Close the ink tank cover.
13 Follow the on-screen instructions to adjust the print
quality. Select OK to continue.
2
npack the ink bottle. Hold the ink bottle upright and
U
slowly turn the bottle cap to remove it.
Note:
• You need to load paper before you can adjust the print quality.
See “Load paper” below for details.
• Select Adjust Later if you want to adjust the print quality later.
For more information, see the online User’s Guide.
8
onnect the power cord to the back of the product and to
C
an electrical outlet.
Caution: Do not shake or squeeze the ink bottle. Do not touch
the top of the ink bottle after its cap is removed.
3
3 Load paper
See the online User’s Guide for information about loading
capacity, available paper types and sizes, loading envelopes,
and using the rear paper feed slot or ADF.
Insert the ink bottle into the filling port, as shown below.
1
Caution: Do not connect to your computer yet.
Note: Do not force the bottle into position.
ake sure the product is done charging the ink. Open the
M
paper cassette cover and pull out the paper cassette until
it stops.
ET-M3170
2
Remove all protective materials from the product.
4
Wait for the ink to fill the tank. Do not squeeze the bottle.
9
Press the power button to turn on the product, then
wait for the power light to stop flashing.
Start Here
IMPORTANT: Before using this product, make sure you read
these instructions and the safety instructions in the online
User’s Guide.
Important Safety Instructions: When using telephone equipment, you
should always follow basic safety precautions to reduce the risk of fire,
electric shock, and personal injury, including the following:
ote: If an error code appears, turn off the product and check
N
that no protective material has been left inside the product.
Caution: Do not touch the flat white cable, translucent film, or
the ink tubes.
3
• Do not use the Epson® product near water.
Note: If ink does not flow from the bottle, lift and reinsert the
bottle.
Close the printer cover.
Caution: After setup, periodically inspect the ink level to ensure
it is not below the lowest line on the tank. Prolonged use when
ink is below the lowest line could damage the product. See the
online User’s Guide for refilling instructions.
Note: Do not connect the power cord yet.
• Always keep this guide handy.
• A
void using a telephone during an electrical storm. There may be a
remote risk of electric shock from lightning.
• Do not use a telephone to report a gas leak in the vicinity of the leak.
Caution: To reduce the risk of fire, use only a No. 26 AWG or larger
telecommunication line cord.
1 Unpack
2
Fill ink tank and charge
the ink
5
10 Select your language, country, time, and date settings on
the LCD screen.
Note: You can change these settings later using the product’s
control panel. For more information, see the online User’s Guide.
11 When the message to see the Start Here sheet appears
on the LCD screen, press and hold the
5 seconds.
hen the ink bottle is empty, remove the bottle and
W
securely close it with the cap.
help button for
Warning: Keep the ink bottle out of the reach of children and do not
drink the ink.
Caution: This product requires careful handling of ink. If ink spills,
wipe it off immediately with a damp towel to avoid permanent stains. If
ink gets on your clothes or belongings, it may not come off.
12 Follow the on-screen instructions to start charging the ink.
Note:
• Epson cannot guarantee the quality or reliability of third-party ink.
• U
se the ink bottle included with the printer to set up the product.
Part of the ink will be used to charge the print head. This bottle may
print fewer pages compared with replacement ink bottles.
1
Ink charging takes approximately 10 minutes. A message
appears when ink charging is complete. Select OK to
continue.
Note: Do not leave the ink bottle inserted; otherwise the bottle
may be damaged or ink may leak.
6
Caution: Do not turn off the product, raise the printer cover, or
load paper while the product is charging or you’ll waste ink.
Close the ink tank cap.
Open the ink tank cover, then open the cap.
Make sure you keep the box shown above for use when
transporting the printer.
Caution: Do not lift the product by gripping the scanner unit. Make
sure you lift using the handholds on the bottom of the product.
Note: After some ink is used for charging, the rest is available
for printing.
Note: Do not open the ink bottle until you are ready to fill the ink tank.
The ink bottle is vacuum packed to maintain reliability.
1
Lift the printer cover until it clicks into place.
7
Close the ink tank cover.
13 Follow the on-screen instructions to adjust the print
quality. Select OK to continue.
2
npack the ink bottle. Hold the ink bottle upright and
U
slowly turn the bottle cap to remove it.
Note:
• You need to load paper before you can adjust the print quality.
See “Load paper” below for details.
• Select Adjust Later if you want to adjust the print quality later.
For more information, see the online User’s Guide.
8
onnect the power cord to the back of the product and to
C
an electrical outlet.
Caution: Do not shake or squeeze the ink bottle. Do not touch
the top of the ink bottle after its cap is removed.
3
3 Load paper
See the online User’s Guide for information about loading
capacity, available paper types and sizes, loading envelopes,
and using the rear paper feed slot or ADF.
Insert the ink bottle into the filling port, as shown below.
1
Caution: Do not connect to your computer yet.
Note: Do not force the bottle into position.
ake sure the product is done charging the ink. Open the
M
paper cassette cover and pull out the paper cassette until
it stops.
2
Slide the edge guides all the way out.
5
Install software
Note:
• If you are using a Mac or your computer does not have a
CD/DVD drive, an Internet connection is required to obtain the
product software.
• T
o print from a Chromebook™, go to
www.epson.com/support/gcp (U.S.) or
www.epson.ca/support/gcp (Canada) for instructions.
3
Insert paper with the printable side down and slide the
edge guides against the paper, but not too tightly.
1
ake sure the product is NOT CONNECTED to your
M
computer.
• Use voice-activated assistants to print a variety of creative
and everyday items from your Epson product. Simply add
your product to an Epson Connect account, then link the
account to a voice-activated assistant. See
www.epson.com/voice (U.S.) or www.epson.ca/voice
(Canada) for more information.
Videos
*M
ay require the Epson Print Enabler or Mopria Print Service app from Google
Play™.
Visit www.epson.com/support/etm3170 (U.S.) or
www.epson.ca/support/etm3170 (Canada) to download
drivers, view manuals, get FAQs, or contact Epson.
Any problems?
Network setup was unsuccessful
• Make sure you select the right network name (SSID).
• Restart your router (turn it off and then on), then try to
connect to it again.
4
eep the cassette flat as you insert it all the way and then
K
close the paper cassette cover.
Note: Make sure the paper is loaded against the front of the
cassette.
5
Select the paper settings on the product’s control panel.
4 Connect the fax line
1
onnect a phone cord to a telephone wall jack and to the
C
LINE port on your product. See the online User’s Guide
for more information.
Windows®: If you see a Found New Hardware screen, click
Cancel and disconnect the USB cable.
• The printer can only connect to a network that supports
2.4 GHz connections. If your router offers both 2.4 GHz and
5 GHz connections, make sure 2.4 GHz is enabled.
Insert the product CD (Windows only) or download and
run your product’s software package. For the latest
software, visit www.epson.com/support/etm3170 (U.S.)
or www.epson.ca/support/etm3170 (Canada).
• If your network has security enabled, make sure you enter
your network password (WEP key or WPA passphrase)
correctly. Be sure to enter your password in the correct
case.
3
ollow the instructions on the computer screen to run the
F
setup program.
There are lines or incorrect colors in my printouts.
4
hen you see the Select Your Connection screen, select
W
one of the following:
Run a nozzle check to see if there are any clogged nozzles.
Then clean the print head, if necessary. See the online User’s
Guide for more information.
In most cases, the software installer automatically
attempts to set up your wireless connection. If setup
is unsuccessful, you may need to enter your network
name (SSID) and password.
• Direct USB connection
Make sure you have a USB cable (not included).
• Wired network connection
If prompted, select Proceed on the LCD screen to set up
the fax, or select Close to set it up later.
Call (562) 276-4382 (U.S.) or (905) 709-3839 (Canada), 6 am to
8 pm, Pacific Time, Monday through Friday, and 7 am to 4 pm,
Pacific Time, Saturday. Days and hours of support are subject
to change without notice. Toll or long distance charges may
apply.
Recycling
Epson offers a recycling program for end of life hardware and
ink bottles. Please go to www.epson.com/recycle (U.S.) or
www.epson.ca/recycle (Canada) for information on how to
return your products for proper disposal.
Need paper and ink?
Ensure brilliant results with Epson specialty
and plain papers, engineered specifically for
Epson printers. Find Epson papers and Epson
Genuine Ink at www.epson.com (U.S. sales)
or www.epson.ca (Canadian sales) and at
Epson authorized resellers. Call
800-GO-EPSON (800-463-7766).
The product’s screen is dark.
Make sure your product is turned on, and touch the screen to
wake it from sleep mode.
Setup is unable to find my product after connecting
it with a USB cable.
Make sure your product is on and securely connected
as shown.
ET-M3170 replacement ink
Color
Black
Make sure you have an Ethernet cable (not included).
2
Technical support
• If you see a firewall alert message, click Unblock or Allow
to let setup continue.
2
• Wireless connection
Visit www.epson.com/support/etm3170videos (U.S.) or
www.epson.ca/support/etm3170videos (Canada) to view
support videos.
Part number
532
Mobile and voice-activated
printing
• Print directly from your iOS device. Simply connect your
printer and device to the same network and tap the action
icon to select the print option.
• Print directly from your Android™ (v4.4 or later) device*.
Simply connect your printer and device to the same network
and tap the menu icon to select the print option.
• Print from wherever you are, next to your printer or remotely,
with Epson Connect™ and Google Cloud Print™. Learn
more at www.epson.com/connect (U.S.) or
www.epson.ca/connect (Canada).
Any questions?
User’s Guide
Windows: Click the icon on your desktop or Apps screen to
access the online User’s Guide.
Mac: Click the icon in Applications/Epson Software/Guide to
access the online User’s Guide.
If you don’t have a User’s Guide icon, go to the Epson website,
as described below.
EPSON is a registered trademark, EPSON Exceed Your Vision is a registered logomark, and
Epson Connect is a trademark of Seiko Epson Corporation.
Designed for Excellence is a trademark of Epson America, Inc.
Mac is a trademark of Apple Inc., registered in the U.S. and other countries.
Windows is a registered trademark of Microsoft Corporation in the United States and/or other
countries.
Android, Chromebook, Google Cloud Print, and Google Play are trademarks of Google LLC.
General Notice: Other product names used herein are for identification purposes only and may
be trademarks of their respective owners. Epson disclaims any and all rights in those marks.
This information is subject to change without notice.
© 2018 Epson America, Inc., 12/18
Printed in XXXXXX
CPD-56730
2
Slide the edge guides all the way out.
5
Install software
Note:
• If you are using a Mac or your computer does not have a
CD/DVD drive, an Internet connection is required to obtain the
product software.
• To print from a Chromebook™, go to
www.epson.com/support/gcp (U.S.) or
www.epson.ca/support/gcp (Canada) for instructions.
3
Insert paper with the printable side down and slide the
edge guides against the paper, but not too tightly.
1
Make sure the product is NOT CONNECTED to your
computer.
• Use voice-activated assistants to print a variety of creative
and everyday items from your Epson product. Simply add
your product to an Epson Connect account, then link the
account to a voice-activated assistant. See
www.epson.com/voice (U.S.) or www.epson.ca/voice
(Canada) for more information.
Videos
* May require the Epson Print Enabler or Mopria Print Service app from Google
Play™.
Visit www.epson.com/support/etm3170 (U.S.) or
www.epson.ca/support/etm3170 (Canada) to download
drivers, view manuals, get FAQs, or contact Epson.
Any problems?
Network setup was unsuccessful
• Make sure you select the right network name (SSID).
• Restart your router (turn it off and then on), then try to
connect to it again.
4
Keep the cassette flat as you insert it all the way and then
close the paper cassette cover.
Note: Make sure the paper is loaded against the front of the
cassette.
5
Select the paper settings on the product’s control panel.
4 Connect the fax line
1
Connect a phone cord to a telephone wall jack and to the
LINE port on your product. See the online User’s Guide
for more information.
Windows®: If you see a Found New Hardware screen, click
Cancel and disconnect the USB cable.
• The printer can only connect to a network that supports
2.4 GHz connections. If your router offers both 2.4 GHz and
5 GHz connections, make sure 2.4 GHz is enabled.
Insert the product CD (Windows only) or download and
run your product’s software package. For the latest
software, visit www.epson.com/support/etm3170 (U.S.)
or www.epson.ca/support/etm3170 (Canada).
• If your network has security enabled, make sure you enter
your network password (WEP key or WPA passphrase)
correctly. Be sure to enter your password in the correct
case.
3
Follow the instructions on the computer screen to run the
setup program.
There are lines or incorrect colors in my printouts.
4
When you see the Select Your Connection screen, select
one of the following:
Run a nozzle check to see if there are any clogged nozzles.
Then clean the print head, if necessary. See the online User’s
Guide for more information.
In most cases, the software installer automatically
attempts to set up your wireless connection. If setup
is unsuccessful, you may need to enter your network
name (SSID) and password.
• Direct USB connection
Make sure you have a USB cable (not included).
• Wired network connection
If prompted, select Proceed on the LCD screen to set up
the fax, or select Close to set it up later.
Call (562) 276-4382 (U.S.) or (905) 709-3839 (Canada), 6 am to
8 pm, Pacific Time, Monday through Friday, and 7 am to 4 pm,
Pacific Time, Saturday. Days and hours of support are subject
to change without notice. Toll or long distance charges may
apply.
Recycling
Epson offers a recycling program for end of life hardware and
ink bottles. Please go to www.epson.com/recycle (U.S.) or
www.epson.ca/recycle (Canada) for information on how to
return your products for proper disposal.
Need paper and ink?
Ensure brilliant results with Epson specialty
and plain papers, engineered specifically for
Epson printers. Find Epson papers and Epson
Genuine Ink at www.epson.com (U.S. sales)
or www.epson.ca (Canadian sales) and at
Epson authorized resellers. Call
800-GO-EPSON (800-463-7766).
The product’s screen is dark.
Make sure your product is turned on, and touch the screen to
wake it from sleep mode.
Setup is unable to find my product after connecting
it with a USB cable.
Make sure your product is on and securely connected
as shown.
ET-M3170 replacement ink
Color
Black
Make sure you have an Ethernet cable (not included).
2
Technical support
• If you see a firewall alert message, click Unblock or Allow
to let setup continue.
2
• Wireless connection
Visit www.epson.com/support/etm3170videos (U.S.) or
www.epson.ca/support/etm3170videos (Canada) to view
support videos.
Part number
532
Mobile and voice-activated
printing
• Print directly from your iOS device. Simply connect your
printer and device to the same network and tap the action
icon to select the print option.
• Print directly from your Android™ (v4.4 or later) device*.
Simply connect your printer and device to the same network
and tap the menu icon to select the print option.
• Print from wherever you are, next to your printer or remotely,
with Epson Connect™ and Google Cloud Print™. Learn
more at www.epson.com/connect (U.S.) or
www.epson.ca/connect (Canada).
Any questions?
User’s Guide
Windows: Click the icon on your desktop or Apps screen to
access the online User’s Guide.
Mac: Click the icon in Applications/Epson Software/Guide to
access the online User’s Guide.
If you don’t have a User’s Guide icon, go to the Epson website,
as described below.
EPSON is a registered trademark, EPSON Exceed Your Vision is a registered logomark, and
Epson Connect is a trademark of Seiko Epson Corporation.
Designed for Excellence is a trademark of Epson America, Inc.
Mac is a trademark of Apple Inc., registered in the U.S. and other countries.
Windows is a registered trademark of Microsoft Corporation in the United States and/or other
countries.
Android, Chromebook, Google Cloud Print, and Google Play are trademarks of Google LLC.
General Notice: Other product names used herein are for identification purposes only and may
be trademarks of their respective owners. Epson disclaims any and all rights in those marks.
This information is subject to change without notice.
© 2018 Epson America, Inc., 12/18
CPD-56730
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement