Extron XTP R HWP 201 Manual

Extron XTP R HWP 201 Manual

XTP R HWP 201 XTP Receiver – Decorator-Style Wallplate

User Guide

XTP Systems

68-2339-01 Rev. E 01 1 9

Safety Instructions

Safety Instructions • English

WARNING: This symbol, , when used on the product, is intended to alert the user of the presence of uninsulated dangerous voltage within the product’s enclosure that may present a risk of electric shock.

ATTENTION: This symbol, , when used on the product, is intended to alert the user of important operating and maintenance (servicing) instructions in the literature provided with the equipment.

For information on safety guidelines, regulatory compliances, EMI/EMF compatibility, accessibility, and related topics, see the Extron Safety and Regulatory Compliance Guide, part number 68-290-01, on the Extron website,

www.extron.com

.

Sicherheitsanweisungen • Deutsch

WARNUNG: Dieses Symbol auf dem Produkt soll den Benutzer darauf aufmerksam machen, dass im Inneren des Gehäuses dieses Produktes gefährliche Spannungen herrschen, die nicht isoliert sind und die einen elektrischen Schlag verursachen können.

VORSICHT

:

Dieses Symbol auf dem Produkt soll dem Benutzer in der im Lieferumfang enthaltenen Dokumentation besonders wichtige Hinweise zur Bedienung und Wartung (Instandhaltung) geben.

Weitere Informationen über die Sicherheitsrichtlinien, Produkthandhabung, EMI/EMF-Kompatibilität, Zugänglichkeit und verwandte Themen finden Sie in den Extron-Richtlinien für Sicherheit und Handhabung (Artikelnummer 68-290-01) auf der Extron-Website,

www.extron.com

.

Instrucciones de seguridad • Español

ADVERTENCIA: Este símbolo, , cuando se utiliza en el producto, avisa al usuario de la presencia de voltaje peligroso sin aislar dentro del producto, lo que puede representar un riesgo de descarga eléctrica.

ATENCIÓN:

al usuario de la presencia de importantes instrucciones de uso y mantenimiento recogidas en la documentación proporcionada con el equipo.

Este símbolo, , cuando se utiliza en el producto, avisa Para obtener información sobre directrices de seguridad, cumplimiento de normativas, compatibilidad electromagnética, accesibilidad y temas relacionados, consulte la Guía de cumplimiento de normativas y seguridad de Extron, referencia 68-290-01, en el sitio Web de Extron,

www.extron.com

.

Instructions de sécurité • Français AVERTISSEMENT :

produit, signale à l’utilisateur la présence à l’intérieur du boîtier du produit d’une tension électrique dangereuse susceptible de provoquer un choc électrique.

Ce pictogramme, , lorsqu’il est utilisé sur le

ATTENTION :

Ce pictogramme, , lorsqu’il est utilisé sur le produit, signale à l’utilisateur des instructions d’utilisation ou de maintenance importantes qui se trouvent dans la documentation fournie avec le matériel.

Pour en savoir plus sur les règles de sécurité, la conformité à la réglementation, la compatibilité EMI/EMF, l’accessibilité, et autres sujets connexes, lisez les informations de sécurité et de conformité Extron, réf. 68-290-01, sur le site Extron,

www.extron.com

.

Istruzioni di sicurezza • Italiano

AVVISO: Il simbolo, , se usato sul prodotto, serve ad avvertire l’utente della presenza di tensione non isolata pericolosa all’interno del contenitore del prodotto che può costituire un rischio di scosse elettriche.

ATTENTZIONE: Il simbolo, , se usato sul prodotto, serve ad avvertire l’utente della presenza di importanti istruzioni di funzionamento e manutenzione nella documentazione fornita con l’apparecchio.

Per informazioni sulle linee guida di sicurezza, adempimenti normativi, compatibilità EMI/EMF, accessibilità e argomenti correlati, vedere la sicurezza di Extron e Regulatory Compliance Guide, parte numero 68-290-01, sul sito Web Extron,

www.extron.com

.

Instrukcje bezpieczeństwa • Polska OSTRZEŻENIE:

Ten symbol, porażenia prądem elektrycznym.

, gdy używany na produkt, ma na celu poinformować użytkownika o obecności izolowanego i niebezpiecznego napięcia wewnątrz obudowy produktu, który może stanowić zagrożenie

UWAGI:

Ten symbol, , gdy używany na produkt, jest przeznaczony do ostrzegania użytkownika ważne operacyjne oraz instrukcje konserwacji (obsługi) w literaturze, wyposażone w sprzęt.

Informacji na temat wytycznych w sprawie bezpieczeństwa, regulacji wzajemnej zgodności, zgodność EMI/EMF, dostępności i Tematy pokrewne, zobacz Extron bezpieczeństwa i regulacyjnego zgodności przewodnik, część numer 68-290-01, na stronie internetowej Extron,

www.extron.com

.

Инструкция по технике безопасности • Русский ПРЕДУПРЕЖДЕНИЕ:

на продукте, предупреждает пользователя о наличии неизолированного опасного напряжения внутри корпуса продукта, которое может привести к поражению электрическим током.

Данный символ, , если указан

ВНИМАНИЕ:

Данный символ, , если указан на продукте, предупреждает пользователя о наличии важных инструкций по эксплуатации и обслуживанию в руководстве, прилагаемом к данному оборудованию.

Для получения информации о правилах техники безопасности, соблюдении нормативных требований, электромагнитной совместимости (ЭМП/ЭДС), возможности доступа и других вопросах см. руководство по безопасности и соблюдению нормативных требований Extron на сайте Extron:

www.extron.com

, номер по каталогу - 68-290-01.

安全说明

简体中文 警告 : 产品上的这个标志意在警告用户该产品机壳内有暴露的危险 电压, 有触电危险。

注 意

: 产 品 上 的 这个 标 志 意 在 提 示 用 户 设 备 随 附 的 用 户 手 册 中 有 重要的操作和维护(维修)说明。 关于我们产品的安全指南、遵循的规范、EMI/EMF 的兼容性、无障碍 使用的特性等相关内容,敬请访问 Extron 网站

www.extron.com

,参见 Extron 安全规范指南,产品编号 68-290-01 。

安全記事

繁體中文 警告 : 若產品上使用此符號,是為了提醒使用者,產品機殼內存在著 可能會導致觸電之風險的未絕緣危險電壓。

注意

: 若產品上使用此符號,是為了提醒使用者,設備隨附的用戶手冊中有重 要的操作和維護(維修)説明 。 有關安全性指導方針、法規遵守、EMI/EMF 相容性、存取範圍和相關主題的詳細資 訊,請瀏覽 Extron 網站:

www.extron.com

,然後參閱《Extron 安全性與法規 遵守手冊》,準則編號 68-290-01。 安全上のご注意

日本語

警告:

この記号 が製品上に表示されている場合は、筐体内に絶縁されて いない高電圧が流れ、感電の危険があることを示しています。

注意:

この記号 が製品上に表示されている場合は、本機の取扱説明書に 記載されている重要な操作と保守(整備)の指示についてユーザーの 注意を喚起するものです。 安全上のご注意、法規厳守、EMI/EMF適合性、その他の関連項目に ついては、エクストロンのウェブサイト

www.extron.com

より 『 Extron Safety and Regulatory Compliance Guide 』 ( P/N 68-290-01 ) をご覧ください。

안전 지침 • 한국어 경고:

이 기호 가 제품에 사용될 경우, 제품의 인클로저 내에 있는 접지되지 않은 위험한 전류로 인해 사용자가 감전될 위험이 있음을 경고합니다.

주의:

이 기호 가 제품에 사용될 경우, 장비와 함께 제공된 책자에 나와 있는 주요 운영 및 유지보수(정비) 지침을 경고합니다.

안전 가이드라인, 규제 준수, EMI/EMF 호환성, 접근성, 그리고 관련 항목에 대한 자세한 내용은 Extron 웹 사이트(

www.extron.com

)의 Extron 안전 및 규제 준수 안내서, 68-290-01 조항을 참조하십시오..

Copyright

© 2017 -2019 Extron Electronics. All rights reserved.

Trademarks

All trademarks mentioned in this guide are the properties of their respective owners. The following registered trademarks ( ® ), registered service marks ( SM ), and trademarks (™) are the property of RGB Systems, Inc. or Extron Electronics (see the current list of trademarks on the

Terms of Use

page at

www.extron.com

) :

Registered Trademarks (®)

Extron, AVTrac, Cable Cubby, ControlScript, CrossPoint, DTP, eBUS, EDID Manager, EDID Minder, Flat Field, FlexOS, Global Configurator, Global Scripter, GlobalViewer, Hideaway, Inline, IP Intercom, IP Link, Key Minder, LinkLicense, LockIt, MediaLink, MediaPort, NetPA, PlenumVault, PoleVault, PowerCage, PURE3, Quantum, SoundField, SpeedMount, SpeedSwitch, System 

INTEGRATOR

, TeamWork, TouchLink, V-Lock, VersaTools, VN-Matrix, VoiceLift, WallVault, WindoWall, XTP, and XTP Systems

Registered Service Mark (SM) :

S3 Service Support Solutions

Trademarks ( ™ )

AAP, AFL (Accu-Rate Frame Lock), ADSP (Advanced Digital Sync Processing), Auto-Image, CableCover, CDRS (Class D Ripple Suppression), DDSP (Digital Display Sync Processing), DMI (Dynamic Motion Interpolation), Driver Configurator, DSP Configurator, DSVP (Digital Sync Validation Processing), eLink, EQIP, Everlast, FastBite, FOX, FOXBOX, HyperLane, IP Intercom HelpDesk, MAAP, MicroDigital, Opti-Torque, ProDSP, QS-FPC (QuickSwitch Front Panel Controller), Room Agent, Scope-Trigger, ShareLink, SIS, Simple Instruction Set, Skew-Free, SpeedNav, Triple-Action Switching, True4K, Vector™ 4K, WebShare, XTRA, ZipCaddy, ZipClip

FCC Class A Notice

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC rules. The Class A limits provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause interference. This interference must be corrected at the expense of the user.

ATTENTION: The Twisted Pair Extension technology works with unshielded twisted pair (UTP) or shielded twisted pair (STP) cables; but to ensure FCC Class A and CE compliance, STP cables and STP Connectors are required.

For more information on safety guidelines, regulatory compliances, EMI/EMF compatibility, accessibility, and related topics, see the “

Extron Safety and Regulatory Compliance Guide

” on the Extron website.

Conventions Used in this Guide

Notifications

The following notifications are used in this guide: WARNING: Potential risk of severe injury or death. AVERTISSEMENT : Risque potentiel de blessure grave ou de mort.

ATTENTION:

• •

Risk of property damage. Risque de dommages matériels.

NOTE: A note draws attention to important information.

TIP: A tip provides a suggestion to make working with the application easier.

Software Commands

Commands are written in the fonts shown here: ^AR Merge Scene,,Op1 scene 1,1 ^B 51 ^W^C [01] R 0004 00300 00400 00800 00600 [02] 35 [17] [03] EX!

* X1& * X2) * X2# * X2!

CE } NOTE: For commands and examples of computer or device responses mentioned in this guide, the character “ 0 ” is used for the number zero and “ O ” represents the capital letter “ o .” Computer responses and directory paths that do not have variables are written in the font shown here: Reply from 208.132.180.48: bytes=32 times=2ms TTL=32 C:\Program Files\Extron Variables are written in slanted form as shown here: ping

xxx.xxx.xxx.xxx

—t SOH R

Data

STX

Command

ETB ETX Selectable items, such as menu names, menu options, buttons, tabs, and field names are written in the font shown here: From the

File

menu, select

New

.

Click the

OK

button.

Specifications Availability

Product specifications are available on the Extron website,

www.extron.com

.

Extron Glossary of Terms

A glossary of terms is available at

http://www.extron.com/technology/glossary.aspx

.

Contents

Introduction

............................................... 1 Guide Overview ................................................... 1 XTP R HWP 201 Wallplate Receiver Description ......................................................... 1

System Compatibility ........................................... 2 Features .............................................................. 2

Installation

................................................. 4 Installation Overview ............................................ 4

Metal Junction Box or Mud Ring Installation ........ 5 Mounting Surface Preparation ......................... 5

Mud Ring Installation ....................................... 6

UL Listed Metal Junction Box Installation ......... 7

Rear and Side Panel Connectors ......................... 8

Mounting the XTP R HWP 201 ............................ 9

Front Panel Connectors ..................................... 10

Connection Details ............................................ 11 HDMI Connection .......................................... 11

TP Cable Termination and Recommendations ....................................... 12

RS-232 and IR Over XTP Communication ..... 14 Power Connection ......................................... 14

Operation

................................................. 17 Front Panel Features .......................................... 17 HDMI Audio Switch ........................................... 17

Audio Output Overview ...................................... 18 Reset Mode ....................................................... 18

Side Panel Indicators ......................................... 19

SIS Configuration and Control

................. 20 Host Device Connection .................................... 20 SIS Overview ..................................................... 20 Host-to-Device and Device-to-Host Communication ............................................ 20 Error Responses ............................................ 20

Using the Command and Response Tables for SIS Commands ....................................... 21 Symbol Definitions ......................................... 21

Command and Response Tables for SIS Commands ...................................................... 22 Audio Configuration Commands .................... 22

Advanced Configuration Commands ............. 23

XTP System Configuration Software

........ 24 Software Installation........................................... 24 Software Download Center Page ................... 24

Software Product Page .................................. 25

Software Operation............................................ 26 Connections .................................................. 26

Menu Bar ...................................................... 27

Device Settings .............................................. 30

Reference Information

............................. 32 Mounting Template ............................................ 32

XTP R HWP 201 Wallplate Receiver • Contents vii

XTP R HWP 201 Wallplate Receiver • Contents viii

Introduction

This section contains general information about this guide and the Extron XTP R HWP 201 Wallplate Receiver, and selected device features. Topics in this section include: •

Guide Overview

• •

XTP R HWP 201 Wallplate Receiver Description

System Compatibility

Features

Guide Overview

This guide contains installation, operation, and control procedures, as well as reference information for the XTP R HWP 201 Wallplate Receiver. In this guide, the terms “XTP R HWP 201” and “receiver” are used interchangeably to refer to all models of the XTP R HWP 201 Wallplate Receiver.

XTP R HWP 201 Wallplate Receiver Description

The Extron XTP R HWP 201 is a-style wallplate receiver, ideal for XTP Systems that include wall-mounted displays. The HDMI output connector is oriented upward at a 90° angle, which minimizes stress on the cable and allows for a low-profile flat panel display installation. The receiver accepts XTP signals from up to 330 feet (100 meters) away over a single shielded twisted pair cable. It outputs video, audio, bidirectional RS-232 and IR, and Ethernet to the display. It also provides HDMI audio de-embedding with analog stereo audio output and volume control.

The XTP R HWP 201 can be powered locally or remotely through an Extron Power Injector

or XTP matrix switcher (see

Power Connection

on page 14).

To configure and control the XTP R HWP 201, connect a host device, such as a computer, through the USB Config port and enter Simple Instruction Set (SIS) commands (see

SIS Configuration and Control

on page 20) or use the XTP System Configuration Software

(see

XTP System Configuration Software

on page 24).

XTP R HWP 201 Wallplate Receiver • Introduction 1

The following diagram shows one way the XTP R HWP 201 can be integrated in an XTP point-to-point application. The transmitter can also be used with an XTP matrix switcher (see the XTP matrix switcher user guide for more details on matrix applications and configuration).

Shielded Twisted Pair Cable

Extron XTP T UWP 202

Universal XTP Transmitter

PWR HDC P HD MI HDMI IN VGA RESET AU CL DIO IP AUTO SWITCH CON FIG LAN VGA IN

Audio VGA HDMI Laptops Display

L AUDI O R OV RS 232 P IR Tx Rx G LAN Tx Rx HDMI OUT PWR SIG AUD IO Extron XTP R HWP 201

XTP Decorator-Style Wallplate Receiver for HDMI HDMI

Figure 1. Typical Point-to-Point Application Diagram

System Compatibility

The XTP R HWP 201 is compatible with XTP Systems, but the maximum video resolution may be limited with different XTP devices. See the table below for maximum video resolutions and refresh rates for various XTP Systems.

Analog Non-4K Digital 4K Fiber 4K PLUS Non-4K

1920x1200 @ 60 Hz 2048x1080 @ 60 Hz 2048x1080 @ 60 Hz 2048x1080 @ 60 Hz

Output 4K Fiber 4K Plus

1920x1200 @ 60 Hz 1920x1200 @ 60 Hz 2048x1080 @ 60 Hz 2048x1080 @ 60 Hz 4096x2160 @ 24 Hz 4096x2160 @ 24 Hz 4096x2160 @ 24 Hz 4096x2160 @ 60 Hz

Features

• • •

Reliable cable infrastructure

— Provides high reliability and maximum performance on an economical and easily installed cable infrastructure.

Unique low-profile wallplate design

— Requires minimal space behind a flat panel display. The HDMI port is oriented upward at a 90-degree angle to solve the long standing issue of limited space behind a wall-mounted display. A convenient cable tie down point further ensures full stabilization of the connection.

Wall mountable

— Mounts in a two-gang metal junction box or the provided mud ring.

XTP R HWP 201 Wallplate Receiver • Introduction 2

• • • • • • • • • • • • • • •

Support for computer-video to 1920x1200, including HDTV 1080p/60 Deep Color and 2K signals

— Maintains superior image quality at the highest resolutions.

Shielded twisted pair cable compatibility

— Optimized for use with common shielded twisted pair cable types. XTP Systems fully support a maximum transmission distance of 330 feet (100 meters) for all compatible resolutions when used with shielded twisted pair cable. Shielded twisted pair cabling with solid center conductor sizes of 24 AWG or better is recommended for optimal performance.

Bidirectional RS-232 and IR insertion

signals inserted into the XTP output.

— Allows a remote display to be controlled without the need for additional cabling through bidirectional RS-232 control and IR

HDMI specification features

— Support data rates up to 6.75 Gbps, Deep Color up to 12-bit, 3D, and HD lossless audio formats.

HDCP compliance

— Ensures display of content-protected media and interoperability with other HDCP-compliant devices.

EDID Minder

— Automatically manages EDID communication between connected devices to ensure that all sources properly power up and reliably display content.

Key Minder

— Authenticates and maintains continuous HDCP encryption between input and output devices to ensure quick and reliable switching in professional AV environments, while enabling simultaneous distribution of a single source signal to one or more displays.

Ethernet extension

— Provides centralized 10/100 Ethernet communication through an Ethernet pass-through port to reduce the amount of independent network drops that are required within a system.

HDMI audio de-embedding

— Supports digital HDMI audio de-embedding as a balanced or unbalanced analog stereo signal on a captive screw connector.

Remote power capability

— Allows the XTP R HWP 201 to be powered by an XTP CrossPoint Matrix Switcher or XTP Power Injectors to simplify integration.

Multiple embedded audio formats

— Provides reliable operation with HDMI sources, compatible with a broad range of multi-channel audio signals.

EDID and HDCP transmission

— Allows continuous communication between source and display by actively buffering DDC channels.

Selectable HDMI audio pass-through

— Enables or disables audio signal pass-through on the HDMI output.

HDMI to DVI interface format correction

— Automatically reformats HDMI source signals for output to a connected DVI display.

XTP compatibility

— Provides a completely integrated solution for multiple digital and analog formats through XTP integrated system products. XTP is a flexible, reliable signal switching and distribution system.

XTP R HWP 201 Wallplate Receiver • Introduction 3

Installation

This section contains information for mounting, connecting, and wiring the XTP R HWP 201. Topics in this section include: • •

Installation Overview

Metal Junction Box or Mud Ring Installation

• •

Rear and Side Panel Connectors

Mounting the XTP R HWP 201

• •

Front Panel Connectors

Connection Details

Installation Overview

The XTP R HWP 201 can be installed into the provided mud ring or an optional UL Listed metal electrical junction box.

ATTENTION:

Do not mount multiple devices adjacent to each other in the same metal junction box. Add at least a one gang space between devices.

Ne procédez pas à une installation juxtaposée des appareils dans le même boîtier de dérivation métallique. Veuillez laisser un espace d’un gang minimum entre chaque appareil.

1.

Prepare the mounting surface.

CAUTION:

Risk of personal injury

. Failure to check the items listed below may result in personal injury.

ATTENTION :

Risque de blessure.

La non-vérification des éléments listés ci-dessous peut provoquer des blessures.

ATTENTION:

Failure to check the items listed below may result in property damage.

La non-vérification des éléments listés ci-dessous peut provoquer des dommages matériels.

• • • • Ensure there are no utility cables or pipes at the intended location that might be damaged or cause injury when installing the device.

Check that the installation meets building, electrical, and safety codes.

Ensure there is sufficient space behind the device.

Choose a location that will allow cable runs without interference.

NOTES:

Cables may need to be installed in the wall or conduits before installation.

The mud ring does not require attachment to wall studs.

XTP R HWP 201 Wallplate Receiver • Installation 4

2. 3. 4. 5. 6. 7.

Cut a hole in the mounting surface (see

Mounting Surface Preparation

below).

Install the mud ring or metal junction box in the mounting surface (see

Mud Ring Installation

on the next page or

UL Listed Metal Junction Box Installation

on

page 7).

Route and connect cables to the rear and side panel connectors (see

Rear and Side Panel Connectors

on page 8).

Mount the XTP R HWP 201 to the mud ring or metal junction box (see

Mounting the XTP R HWP 201

on page 9).

Connect inputs to the front panel connectors (see

Front Panel Connections

on page 10).

Supply power to all connected devices.

Metal Junction Box or Mud Ring Installation

Mounting Surface Preparation

1.

Using an appropriate template or the mounting enclosure as a guide, mark the area

of the wall that will be cut with a soft pencil (for the provided mud ring, see

Mounting Template

on page 32).

NOTES:

If using a junction box, use a UL Listed metal one only.

• •

Check with the manufacturer of the metal junction box for specific installation requirements.

Install junction boxes against wall studs.

2.

Use a jigsaw or small hand saw to carefully cut away the material within the guidelines drawn in step 1.

NOTE: If using a template or the mud ring as a guide for cutting the hole in drywall, cut inside the guidelines to maximize the contact between the mud ring and drywall.

3.

If using a mud ring in a wall with insulation inside, remove at least 6 inches of the insulation in all directions around the cutout.

NOTE: If a wall stud interferes with removing 6 inches of insulation around the cutout, remove the insulation between the cutout and wall stud.

4. 5.

Check the size of the opening by laying the mud ring or metal junction box against it. The mounting device should fit snugly in the opening.

If needed, use a saw, file, or sandpaper to enlarge the hole.

CAUTION:

Risk of personal injury

. Smooth the edges of the opening to avoid personal injury during installation.

ATTENTION :

Risque de blessure.

Lissez les bords de l’ouverture afin d’éviter toute blessure lors de l’installation.

ATTENTION:

Smooth the edges of the opening to avoid damage to the mounting device or the cables.

Lissez les bords de l’ouverture afin d’éviter d’endommager l’appareil de montage ou les câbles.

XTP R HWP 201 Wallplate Receiver • Installation 5

Mud Ring Installation

Backing Clip Mounting Screw Rotate the backing clip out of the way to insert the mud ring into the wall.

Figure 2. 1. 2. 3. 4. Installing the Mud Ring with Backing Clips

Place 1.25 inches (3.18 cm) long or 0.75 inch (1.90 cm) #6-32 thread machine screws through the large holes in the two corners of the mounting bracket. Use the shortest possible screw needed.

Loosely fasten the mounting backing clip on the end of each screw.

Insert the mounting bracket into the opening in the wall (see

Mounting Surface Preparation

on the previous page).

Rotate each backing clip so that the tab is behind the installation surface to hold the bracket snuggly in place when the screw is tightened.

NOTE: The backing clip can be installed as shown in Layout A or Layout B (see figure 3).

Mounting Surface Backing Clip Mounting Surface Backing Clip 0.75" #6-32 Screw 1.25" #6-32 Screw

Layout A Layout B 5. Figure 3. Backing Clip Installation

Use a cross-head (Phillips) screwdriver to fasten the screws and backing clips in place.

XTP R HWP 201 Wallplate Receiver • Installation 6

UL Listed Metal Junction Box Installation

Metal junction boxes may differ slightly from model to model.

NOTES:

If using a junction box, use a metal one only.

Check with the manufacturer of the metal junction box for specific installation requirements.

Wall Stud Screws or Nails Wall opening is flush with edge of box.

Cable Clamp Signal Input Cable

Figure 4. 1. 2. 3. 4. 5. Installing a Metal Junction Box

Insert the metal junction box into the hole in the wall (see

Preparation

on page 5).

Mounting Surface

Secure it to the stud using two screws or nails, as appropriate. The front edge of the metal junction box must be flush with the front surface of the wall.

Feed cables through a knockout opening in the metal junction box.

Secure cables with clamps or ties to provide strain relief.

Trim back and insulate shields with heat shrink.

ATTENTION:

To prevent short circuits, the outer foil shield can be cut back to the point where the cable exits the cable clamp. Both braided and foil shields should be connected to an equipment ground at the other end of the cable.

Afin d’éviter les court circuits, le blindage en aluminium extérieur peut être réduit jusqu’à ce que le câble sorte de la cosse de câble. Le blindage tressé et le blindage en aluminium devraient être connectés à la masse d’un équipement à l’autre bout du câble.

XTP R HWP 201 Wallplate Receiver • Installation 7

Rear and Side Panel Connectors

B

POWER 12V XTP R HWP 201 XTP IN PWR SIG AUDIO Rear

A

Side

A

Figure 5. Rear Panel Connectors

A

XTP Input connector

pass all signals (see

— Connect a twisted pair cable to the RJ-45 connector labeled “XTP IN” on the XTP R HWP 201 and the XTP output port on another XTP device to

TP Cable Termination and Recommendations

on page 12). This cable carries the following signals: • Digital video • • Digital audio Bidirectional RS-232 and IR commands • • • Remote power Ethernet communication System communication

Signal LED indicator

— Lights green when the receiver is receiving an active XTP input signal.

Link LED indicator

— Lights yellow when XTP devices are connected and communication is established.

Signal Link ATTENTION:

Do not connect this connector to a computer data or telecommunications network.

• •

Ne connectez pas ce connecteur à un réseau de données informatiques ou à un réseau de télécommunications.

XTP remote power is intended for indoor use only. No part of the network that uses XTP remote power should be routed outdoors (see

Remote power

on page 16).

XTP à distance est destiné à une utilisation en intérieur seulement. Aucune partie du réseau qui utilise l’alimentation XTP à distance ne peut être routée en

extérieur (voir

Remote power

à la page 16).

B

Power connector

— Connect an external power supply to the 2-pole direct insertion captive screw connector. Confirm the polarity of the power supply wires. For wiring

considerations, see

Power Connection

on page 14.

NOTE:

The XTP R HWP 201 can also be powered remotely (see

Remote power

on page 16).

XTP R HWP 201 Wallplate Receiver • Installation 8

Mounting the XTP R HWP 201

NOTE: Some connectors and features are inaccessible after the device is mounted or the faceplate is attached.

1 e 2 3

XTP R HWP 201 Figure 6.

Decorator-Style Faceplate

Installing the XTP R HWP 201 in the Provided Mud Ring

Wall Stud Cable Clamp e Signal Output Cable

XTP R HWP 201

Decorator-Style Faceplate

Figure 7. 1. 2. 3. Installing the XTP R HWP 201 in a Metal Junction Box

Align the mounting screws on the XTP R HWP 201 with the available holes on the mud ring (see figure 6, 1 ) or metal junction box (see figure 7, 1 ).

Using the provided screws, attach the XTP R HWP 201 to the mud ring (see figure 6, 2 ) or metal junction box (see figure 7, 2 ).

Use four mounting screws to attach the decorator-style faceplate to the XTP R HWP 201 (see figure 6 or 7, 3 ).

XTP R HWP 201 Wallplate Receiver • Installation 9

Front Panel Connectors

A

Top

B C D E

L AUDIO R OVER XTP RS-232 IR Tx Rx G Tx Rx LAN HDMI AUDIO ON OFF RESET CONFIG HDMI OUT

A

Front

A

HDMI output connector

(see page 10)

B

Analog audio output connector

(see page 10) C

RS-232 and IR Over XTP connector

(see page 11) D

LAN connector

(see page 11) E

Configuration port

(see page 11)

Figure 8. Front Panel Connectors

A

HDMI output connector

DisplayPort video sources.

— Connect a digital video display to the female HDMI connector. It accepts HDMI, DVI (with an appropriate adapter), or dual mode NOTES:

The maximum HDMI cable length is 15 feet (4.6 meters).

Use a tie wrap and the front panel lance punch to secure the HDMI connector

to the device (see

HDMI Connection

on the next page).

B

Analog audio output connector

— Connect a balanced or unbalanced, stereo or mono audio output device to the 3.5 mm, 5-pole captive screw connector for 2-channel stereo analog audio output (see figure 9 for wiring details).

No Ground Here Tip Ring Sleeves Tip Ring Tip Sleeves Tip

Do not tin the wires!

Balanced Audio Output

No Ground Here

Unbalanced Audio Output Figure 9. Audio Output Wiring XTP R HWP 201 Wallplate Receiver • Installation 10

C

RS-232 Over XTP port

— To pass bidirectional serial or other control signals between XTP-compatible devices, connect a control device to the

5-pole captive screw connector (see

figure 8

, C on the previous page). The port includes only the 3 poles labeled “RS-232.”

IR Over XTP port

connect a control device to the 5-pole captive screw connector (see

figure 8

,

C — To transmit and receive IR signals (up to 56 kHz), on the previous page). This port includes the 2 poles labeled “IR” and shares the ground pole with the RS-232 port.

RS-232 Tx Rx G Tx Rx RS-232 IR IR Tx Rx G Tx Rx

NOTE: RS-232 and IR data can be transmitted simultaneously (see

RS-232 and IR Over XTP Communication

on page 14 for wiring details). D

LAN connector

— Connect a control device or device to be controlled to this

LAN connector (see

and activity status.

figure 8

,

D on the previous page) for 10/100Base-T Ethernet communication through this pass-through port. LEDs on this connector indicate link E

Configuration port

— If desired, connect a host device to the front panel USB mini-B Config port (see

figure 8

,

E on the previous page) for configuring the receiver.

Connection Details

HDMI Connection

To secure the HDMI cable to the HDMI output connector, use a tie wrap and the front panel lance punch.

1. 2. 3. 4.

Route the tie clip through the front panel lance punch (see 1 in the image to the right).

Plug the HDMI cable into the panel connection ( 2 ).

Loosely place the included tie wrap around the HDMI connector ( 3 ).

Use pliers or similar tools to tighten the tie wrap, then remove any excess length ( 4 ).

ATTENTION:

Connect and pull the tie wraps until they are secure. Do not overtighten.

Connectez et tirez les serre-câbles jusqu’à ce qu’ils soient sécurisés. Ne pas trop serrer.

L AUDIO R OV ER XT P IR Tx Rx G LAN Tx Rx L AUDIO R OV ER XT P IR Tx Rx G LAN Tx Rx HDM I OUT AU SIG DIO

3 4

HDM I OUT SIG AUD XTP R HWP 201 Wallplate Receiver • Installation 11

TP Cable Termination and Recommendations

Use the following pin configurations for twisted pair cables.

Pins:

12345678 5 6 7 8 2 3 4

Pin Pin TIA/EIA-T568B Wire Color T568B Wire color

1 White-orange Orange Orange White-green Orange Blue White-blue Blue White-blue White-blue White-brown Insert Twisted Pair Wires

RJ-45 Connector

8 Brown

Figure 10. TP Cable Termination

Supported cables The XTP R HWP 201 is compatible with shielded twisted pair (F/UTP, SF/UTP, and S/FTP) and unshielded twisted pair (U/UTP) cable. ATTENTION:

Do not use Extron UTP23SF-4 Enhanced Skew-Free AV UTP cable or STP201 cable to link the XTP products.

• •

N’utilisez pas le câble AV Skew-Free UTP version améliorée UTP23SF d’Extron ou le câble STP201 pour relier les produits XTP.

To ensure FCC Class A and CE compliance, STP cables and STP connectors are required.

Afin de s’assurer de la compatibilité entre FCC Classe A et CE, les câbles STP et les connecteurs STP sont nécessaires.

XTP R HWP 201 Wallplate Receiver • Installation 12

Cable recommendations Extron recommends using the following practices for XTP communication to achieve full transmission distances up to 330 feet (100 meters) and reduce transmission errors.

• • • • Use the following Extron XTP DTP 24 SF/UTP cables and connectors for the best performance: •

XTP DTP 24/1000

Non-Plenum 1000' (305 m) spool 22-236-03 •

XTP DTP 24P/1000

Plenum 1000' (305 m) spool 22-235-03 •

XTP DTP 24 Plug

Package of 10 101-005-02 If not using XTP DTP 24 cable, at a minimum, Extron recommends 24 AWG, solid conductor, STP cable with a minimum bandwidth of 400 MHz.

Terminate cables with shielded connectors to the TIA/EIA-T568B standard (see

figure 10

on the previous page).

Limit the use of more than two pass-through points, which may include patch points, punch down connectors, couplers, and power injectors. If these pass-through points are required, use shielded couplers and punch down connectors.

NOTE: When using STP cable in bundles or conduits, consider the following:

Do not exceed 40% fill capacity in conduits.

Do not comb the cable for the first 20 meters, where cables are straightened, aligned, and secured in tight bundles.

• •

Loosely place cables and limit the use of tie wraps or hook-and-loop fasteners.

Separate twisted pair cables from AC power cables.

XTP R HWP 201 Wallplate Receiver • Installation 13

RS-232 and IR Over XTP Communication

The RS-232 and IR Over XTP connector is for pass-through transmission of serial signals, such as projector control signals, and infrared data. To pass bidirectional serial command signals between XTP-compatible devices, connect a control device to the three poles (Tx, Rx, and G) under “RS-232” of the 5-pole captive screw connector. To transmit and receive IR signals, connect a control device to the three poles (G, Tx, and Rx) under “IR.” The ground (G) pole is shared.

NOTE: RS-232 and IR data can be transmitted or received simultaneously (see figure 11 for wiring considerations).

Custom

Rx Tx G Tx Rx G

RS-232 Device Figure 11. Wiring the RS-232 and IR Over XTP Connector

ATTENTION: The length of the exposed wires in the stripping process is important. ATTENTION : La longueur des câbles exposés est importante lorsque l’on entreprend de les dénuder.

• • • •

The ideal length is 3/16 inch (5 mm).

La longueur idéale est de 5 mm (3/16 inches).

Any longer and the exposed wires may touch, causing a short circuit between them. S’ils sont un peu plus longs, les câbles exposés pourraient se toucher et provoquer un court circuit.

Any shorter and the wires can be easily pulled out even if tightly fastened by the captive screws.

S’ils sont un peu plus courts, ils pourraient sortir, même s’ils sont attachés par les vis captives.

Power Connection

Apply power to the receiver locally with the provided power supply (if necessary, see figure 12 for wiring considerations) or remotely (through the XTP connector) with a power injector or an XTP matrix switcher.

Local power

A

Smooth 3/16” (5 mm) Max.

SECTION A–A

Ridges

A

Power Supply Output Cord

Figure 12. Power Wiring

The XTP R HWP 201 can be connected to a local power supply. See the notifications on the next page for local power considerations.

XTP R HWP 201 Wallplate Receiver • Installation 14

WARNING:

Electric shock hazard.

The two power cord wires must be kept separate while the power supply is plugged in. Remove power before wiring.

Avertissement:

Risque de choc électrique grave.

l’alimentation avant de faire l’installation électrique.

Les deux cordons d’alimentation doivent être tenus à l’écart l’un de l’autre quand l’alimentation est branchée. Couper ATTENTION:

This product is intended for use with a UL Listed power source marked “Class 2” or “LPS” rated 12 VDC, 1.0 A minimum, 48 VDC (PoE), minimum 0.35 A, or an Extron UL Listed XTP remote power source. Always use a power supply supplied by or specified by Extron. Use of an unauthorized power supply voids all regulatory compliance certification and may cause damage to the supply and the unit.

• •

Ce produit est destiné à une utilisation avec une source d’alimentation certifiée UL de classe 2 ou LPS et calibrée à 12 Vcc, 1,0 A minimum, 48 Vcc (PoE), 0,35 A minimum, ou une source d’alimentation délocalisée XTP Extron certifiée UL. Utilisez toujours une source d’alimentation fournie par Extron. L’utilisation d’une source d’alimentation non autorisée annule toute conformité réglementaire et peut endommager la source d’alimentation ainsi que l’unité.

Unless otherwise stated, the AC/DC adapters are not suitable for use in air handling spaces or in wall cavities. The installation must always be in accordance with the applicable provisions of National Electrical Code ANSI/NFPA 70, article 725 and the Canadian Electrical Code part 1, section 16. The power supply shall not be permanently fixed to a building structure or similar structure.

• • • • •

Sauf mention contraire, les adaptateurs AC/DC ne sont pas appropriés pour une utilisation dans les espaces d’aération ou dans les cavités murales. Cette installation doit toujours être en accord avec les mesures qui s’applique au National Electrical Code ANSI/NFPA 70, article 725, et au Canadian Electrical Code, partie 1, section 16. La source d’alimentation ne devra pas être fixée de façon permanente à une structure de bâtiment ou à une structure similaire.

Power supply voltage polarity is critical. Incorrect voltage polarity can damage the power supply and the unit. The ridges on the side of the cord identify the power cord negative lead.

La polarité de la source d’alimentation est primordiale. Une polarité incorrecte pourrait endommager la source d’alimentation et l’unité. Les stries sur le côté du cordon permettent de repérer le pôle négatif du cordon d’alimentation.

The length of the exposed (stripped) copper wires is important. The ideal length is 3/16 inch (5 mm).

La longueur des câbles exposés est primordiale lorsque l’on entreprend de les dénuder. La longueur idéale est de 5 mm (3/16 inches).

TIP: Do not tin the stripped power supply leads. Tinned wires are not as secure in the captive screw connectors and could be pulled out.

XTP R HWP 201 Wallplate Receiver • Installation 15

Remote power The XTP R HWP 201 can be powered remotely through an XTP Power Injector or through an XTP matrix switcher.

ATTENTION:

XTP remote power is intended for indoor use only. No part of the network that uses XTP remote power should be routed outdoors.

L’alimentation à distance XTP est destinée à un usage en intérieur uniquement. Aucune partie du réseau qui utilise l’alimentation XTP à distance ne peut être routée en extérieur.

Power injector

To power the XTP R HWP 201 remotely with an XTP Power Injector, power one device locally (see

Local power

on page 14) and connect an XTP Power Injector to the XTP cable run along the XTP ports (see the

XTP Power Injector User Guide

at

www.extron.com

for more installation information).

12V Local Power Supply

Tx Rx G Tx Rx Tx Rx G RS-232 IR OVER XTP RS-232 REMOTE POWER 12V XTP T UWP 202 XTP OUT Extron XTP T UWP 202

XTP Transmitter Shielded Twisted Pair Cable Power

XTP XTP PWR PWR Extron XTP PI 100

XTP Power Injector Remote Power

XTP R HWP 201 XTP IN Figure 13. Extron

XTP Receiver

Typical Point-to-Point Application with Remote Power

NOTE: The power injector provides remote power up to 330 feet (100 meters) with a shielded twisted pair cable with 24 AWG wire.

XTP matrix switcher

XTP matrix switchers have a fixed amount of power available to provide remote power to connected XTP devices (see the XTP matrix switcher user guide for more details). To manage available power from the XTP matrix switcher, use the XTP System Configuration Software with the XTP matrix switcher.

XTP R HWP 201 Wallplate Receiver • Installation 16

Operation

This section contains information for front panel operation and configuration of the XTP R HWP 201. Topics in this section include: •

Front Panel Features

• •

HDMI Audio Switch

Audio Output Overview

• •

Reset Mode

Side Panel Indicators

After all transmitters, all receivers, and other related devices are connected and powered, the system is fully operational. If any problems are encountered, verify that the cables are routed and connected properly. If problems persist, call the Extron S3 Sales & Technical Support Hotline.

Front Panel Features

L AUDIO R OVER XTP RS-232 IR Tx Rx G Tx Rx LAN HDMI AUDIO ON OFF RESET CONFIG HDMI OUT

A B

Figure 14. Front Panel Features

A

HDMI audio switch

— Mutes or enables the embedded audio on the HDMI output connector.

B

Reset button

— Resets the device settings (see

Reset Mode

on the next page).

HDMI Audio Switch

The XTP R HWP 201 has an HDMI audio switch (see figure 14, the embedded audio on the HDMI output connector. If necessary, remove the wallplate to access the switch.

A ) that mutes or enables Move and hold the front panel HDMI audio switch up (on) for about 1 second to enable embedded audio on the associated HDMI connector, or move and hold the HDMI audio switch down (off) for about 1 second to disable embedded audio on the associated HDMI connector. The switch returns to the middle position after it has been released so the device can continue to be controlled through SIS commands.

XTP R HWP 201 Wallplate Receiver • Operation 17

Audio Output Overview

By default, an XTP transmitter or matrix switcher prioritizes embedded digital audio over analog audio. See the table below for a list of supported audio formats.

Available Audio Formats on Output Connectors Audio Input Format HDMI Analog

2-channel LPCM up to 48 kHz Multi-channel PCM up to 7.1, 192 kHz Dolby Digital up to 5.1

Dolby Digital EX Dolby Digital Plus Dolby TrueHD DTS Digital Surround up to 5.1

DTS-ES Matrix 6.1

DTS-ES Discrete 6.1

DTS-HD DTS-HD Master Audio Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes

Reset Mode

Use the recessed

Reset

button (see

figure 14

, B on the previous page) on the front panel of the receiver to restore factory-shipped firmware. To access the

Reset

button, the faceplate may need to be removed.

Mode

Factory Reset 1

Reset Mode Summary Mode Activation

Hold down the recessed device.

Reset

button while applying power to the

Result

The device reverts to the factory default firmware.

NOTE: After a mode 1 reset, update the device with the latest firmware version. DO NOT operate the firmware version that results from this mode reset.

NOTE: If you do not want to update the firmware or perform a mode 1 reset by mistake, cycle power to the device to return to the firmware version running prior to the reset.

Purpose and Notes

Use mode 1 to return to factory firmware for a single power cycle if an incompatibility issue arises.

XTP R HWP 201 Wallplate Receiver • Operation 18

Side Panel Indicators

A

PWR SIG AUDIO Figure 15. Side Panel Indicators

A

LED Indicators:

Power LED indicator

— Lights when power is applied to the device.

• •

Signal LED indicator

— Lights when an active XTP video signal is received.

Audio LED indicator

— Lights when embedded audio output is enabled.

XTP R HWP 201 Wallplate Receiver • Operation 19

SIS Configuration and Control

The XTP R HWP 201 can be configured and controlled using Extron Simple Instruction

Set (SIS) commands or the XTP System Configuration Software (see

XTP System Configuration Software

on page 24). This section contains basic SIS communication details and SIS commands and responses when connected directly to the XTP R HWP 201. Topics in this section include: •

Host Device Connection

• •

SIS Overview

Command and Response Tables for SIS Commands

Host Device Connection

Use a connected computer running the Extron DataViewer utility to send and receive SIS commands and responses. To connect directly to an XTP R HWP 201, connect the computer to the XTP R HWP 201 through the front panel USB configuration port (see

figure 8

,

E on page 10).

SIS Overview

Host-to-Device and Device-to-Host Communication

SIS commands consist of one or more characters per field. No special characters are required to begin or end a command sequence. When the XTP R HWP 201 determines that a command is valid, it executes the command and sends a response to the host device. All responses from the switcher to the host end with a carriage return and a line feed (CR/LF = ] ), which signals the end of the response character string. A string is one or more characters.

Error Responses

When the XTP R HWP 201 receives an SIS command and determines that it is valid, it performs the command and sends the corresponding response to the host device. If the command is determined invalid or contains invalid parameters, the receiver returns an error response to the host. The error response codes are: E10 = Invalid command E13 = Invalid parameter E14 = Not valid for this configuration E17 = Invalid command for signal type E22 = Busy

XTP R HWP 201 Wallplate Receiver • SIS Configuration and Control 20

Using the Command and Response Tables for SIS Commands

The

command and response tables

beginning on the next page list the commands

that the transmitter recognizes as valid, the responses that are returned to the host, and a description of the command function or the results of executing the command. Commands can be entered back-to-back in a string with no spaces. Figure 16 shows the hexadecimal equivalent of ASCII characters used in the command and response tables.

NOTE:

Upper and lowercase text can be used interchangeably unless otherwise stated.

ASCII to Hex Conversion Table

Space •

Figure 16. ASCII to Hexadecimal Conversion

Symbol Definitions

] = Carriage return and line feed } • = Carriage return with no line feed | = Pipe (can be used interchangeably with the } character).

= Space E = Escape key W = Can be used interchangeably with the E character.

XTP R HWP 201 Wallplate Receiver • SIS Configuration and Control 21

Command and Response Tables for SIS Commands

Command ASCII Command (Host to Device)

Audio Configuration Commands

Analog output volume

Set volume Increment volume X@ +V V Decrement volume View volume level

Audio mute

Mute analog and HDMI audio -V V 3Z

Response (Device to Host)

Vol X@] Vol X@] Vol X@] Vol X@] Amt3 ]

Additional Description

Set the output volume to X@ .

Increase the output volume by one increment.

Decrease the output volume by one decrement.

View the output volume level.

Mute analog audio Mute HDMI audio Unmute all outputs View mute status 2Z 1Z 0Z Z Amt2 ] Amt1 ] Amt0 ] Amt X#] Mute the analog and HDMI audio outputs.

Mute the analog audio output.

Mute the HDMI audio output.

Unmute all audio outputs.

View the audio mute status.

NOTES: X@ = Audio output volume X# = Audio mute 0-64 ( 64 = default) 0 = unmute all audio outputs (default) 1 = Mute the HDMI audio output 2 = Mute the analog audio output 3 = Mute the HDMI and analog audio output

XTP R HWP 201 Wallplate Receiver • SIS Configuration and Control 22

Command ASCII Command (Host to Device)

Advanced Configuration Commands

Video mute

Mute output to black 1B Unmute video View mute status

Reset mode

System reset 0B B E ZXXX }

Status

View signal presence View HDCP output status View firmware version View firmware build 0LS E OHDCP } Q *Q

Response (Device to Host)

Vmt1 Zpx ] Vmt0 ] Vmt X$] ] Frq X%] Hdcp X^] x.xx

] x.xx.xxxx

] NOTES: X$ = Video mute X% = Signal status X# = HDCP status

Additional Description

Mute the video and display black video.

Unmute the video.

View the video mute setting.

Reset all user settings back to factory defaults.

View the video or TMDS signal status.

View the HDCP status of the output.

View the current firmware version.

View the current full firmware version.

0 = unmute (default) 1 = Mute video to black 0 = video or TMDS not detected 1 = video or TMDS detected 0 , 2 , 4 , 6 = no sink device detected 1 , 3 , 5 = sink detected with no HDCP encryption 7 = sink detected with HDCP encryption

XTP R HWP 201 Wallplate Receiver • SIS Configuration and Control 23

XTP System Configuration Software

This section contains installation and configuration procedures for the XTP System Configuration Software for configuring and controlling the XTP R HWP 201. Topics in this section include: •

Software Installation

Software Operation

Software Installation

The XTP System Configuration Software is available for download on the Extron website,

www.extron.com

. To download the software from the Extron website, locate it on the Download Center page or go to the XTP System Configuration Software product page (see

Software Product Page

on the next page).

Software Download Center Page

Figure 17. 1. 2. Extron Website Download Page

On the Extron website, select the

Download

tab (see figure 17, From the left sidebar, click the

Software

link ( 2 ).

1 ).

TIP: If the XTP System Configuration Software is featured in the let sidebar, click the

XTP System Configuration Software

link to go directly to the product

page (see

Software Product Page

on the next page).

XTP R HWP 201 Wallplate Receiver • XTP System Configuration Software 24

3. 4. 5. 6. 7. Figure 18. XTP System Configuration Software Download Link

Click the

X

link (see figure 18, 1 ).

Locate the XTP System Configuration Software and click the

Download

link (see figure 18, 2 ) to the right of the product name.

Submit any required information to start the download. Note where the file is saved.

Open the executable (.exe) file from the save location.

Follow the instructions that appear on the screen. By default, the installation creates a directory in the Program Files or Program Files (x86) folder.

Software Product Page

3. 4. 5. 6. Figure 19. 1. 2.

In the Press <

XTP System Configuration Software Product Page Search

Enter field (see figure 19, 1 ) type “ XTP System Configuration Software .” > on the keyboard or select from the drop-down menu.

XTP System Configuration Software

Click the

Download

button (see figure 19, 2 ).

Submit any required information to start the download. Note where the file is saved.

Open the executable (.exe) file from the save location.

Follow the instructions that appear on the screen. By default, the installation creates a directory in the Program Files or Program Files (x86) folder.

XTP R HWP 201 Wallplate Receiver • XTP System Configuration Software 25

Software Operation

The XTP R HWP 201 can be controlled directly from the front panel configuration port (see

figure 8

,

E on page 10) or remotely from an XTP matrix switcher.

Connections

The XTP System Configuration Software opens to the Connections screen. This screen is used to establish communication with an XTP device through USB connection. Ensure the receiver is connected and powered on before attempting to connect to it.

Figure 20. Connections Screen To connect to a device: 1.

Open the XTP System Configuration Software.

2. 3. 4.

From the Connections button (see figure 18, screen in the XTP Configuration Software, select the 1 ).

USB

radio From the displayed list, select the connected device to be controlled ( 2 ).

Click the

Connect

button (

Settings

on page 30).

3 ). The Device Settings

screen opens (see

Device

XTP R HWP 201 Wallplate Receiver • XTP System Configuration Software 26

Menu Bar

The top menu bar contains three menus for configuring software settings.

File menu The File menu contains options for disconnecting from the receiver and exiting the program. To access the menu, click the

File

menu.

Figure 21. File Menu

Disconnect

This option disconnects the connected device from the XTP System Configuration Software. From the

File

menu, select

Disconnect

. The Connections screen opens.

NOTE: If the device is already disconnected, the

Disconnect

option is disabled until a device is connected.

Exit

This option disconnects the receiver from the software and closes the application.

From the

File

menu, select

Exit

to close the application.

Tools menu The Tools menu contains an option for updating firmware. To access this menu, click the

Tools

menu.

Figure 22. Tools Menu

NOTE: The available when directly connected to the device. See an XTP matrix switcher user guide (

www.extron.com

and

Commissioning Report

options are not ) for more information on these features.

XTP R HWP 201 Wallplate Receiver • XTP System Configuration Software 27

Update Firmware

This option uploads firmware from the host device to the connected device.

1.

From the

Tools

menu, select to disconnect from the device.

Update Firmware

. A dialog box opens to ask permission

2. Figure 23. Confirm Disconnect Dialog Box

Click the

Yes

button to disconnect from the device and continue with the firmware update process. The Update Firmware dialog box opens.

3. 4. 5. Figure 24. Update Firmware Dialog Box

Click the

Select file from computer

icon to select a firmware file from the connected host device. The Browse dialog box opens.

Navigate to and select the desired firmware file and click the

Open

button.

Click the

Close

button after the firmware finishes updating.

Software Preference

This option resets all disabled confirmation dialogs to the default settings.

1.

From the

Tools

menu, select dialog box opens.

Software Preference

. The Software Preference

2. Figure 25. Software Preference Dialog Box

Click the

Reset

button. The dialog box closes.

XTP R HWP 201 Wallplate Receiver • XTP System Configuration Software 28

Help menu The

Help

menu contains a way to access XTP System Configuration Software information, a link to the help file, and a link to the Extron website.

Figure 26. Help Menu

NOTE: The connected to the XTP R HWP 201.

option is not available when directly

About the Software

This option provides basic information about the XTP System Configuration Software, including version number and copyright information.

Figure 27. About - XTP System Configuration Software Dialog Box (Example) 1. 2. 3.

From the Click the Click the

Help Details Ok

menu, select

About the Software

button for more information.

button to close the dialog box.

. The About dialog box opens.

Help

This option opens the

XTP System Configuration Software

help file in a Web browser.

From the

Help

menu, select

Help

.

Extron Website

This option opens the Extron website in a Web browser.

From the

Help

menu, select

Extron Website

.

XTP R HWP 201 Wallplate Receiver • XTP System Configuration Software 29

Device Settings

The Device Settings screen allows a user to view and edit various device settings for the device directly connected to the PC running the XTP software. Click the

Device Settings

button (see figure 28, screen.

1 ) on the Global Navigation bar to open the Device Settings

Figure 28. Receiver Device Settings Screen

Video panel The Video panel contains an option to mute the output video.

2

Video Mute

— Click the

Video Mute

button to mute or unmute the output video.

NOTE: The button turns red when the video output is muted.

Relay Control panel The Relay Control panel ( 3 ) is not applicable to the XTP R HWP 201.

Audio panel The Audio panel contains an option to mute all audio outputs, adjust output volume, or enable analog audio for displays connected through DVI.

4

Audio Output

— Click the

Mute All

button to mute or unmute all audio outputs.

NOTE: The button turns red when the output audio is muted.

Analog Audio

— If applicable, move the to adjust the audio volume in decibels.

Analog Audio Volume

slider up or down to adjust the audio volume in percentage or select an amount in the field below the slider NOTE: 0 dB = 100% volume and -64 dB = 0% volume.

If a display is connected through a DVI connection, click the check box below the

Analog Audio Volume

slider to output analog audio.

XTP R HWP 201 Wallplate Receiver • XTP System Configuration Software 30

Factory reset 5

Factory Reset

— Click the

Factory Reset

button (see

figure 28

, 5 on the previous page) to reset the receiver to factory settings except for firmware.

NOTE: This is the same as the command on page 23).

E ZXXX

SIS command (see the

Reset mode

Device Information panel The Device Information information and settings. panel on the right side of the software screen displays device 1

Model

— Displays the device model.

2

Firmware Version

— Displays the full firmware version.

3

Signal Present

— Indicates whether a signal is present on the input.

4

Video Mute

— Displays the mute status of the video output.

5

HDMI Audio

HDMI output.

— Displays the mute status of the embedded digital audio on the 6

S/PDIF Audio

— Not applicable to the XTP R HWP 201.

7

Analog Audio

— Displays the mute status of the analog audio output.

8

Analog Audio Volume

— Displays the analog audio output volume level in a percentage.

XTP R HWP 201 Wallplate Receiver • XTP System Configuration Software 31

Reference Information

This section contains mounting information.

Mounting Template

full scale.

Template for the 2-gang mounting bracket

4.26" (10.82 cm) 4.28" (10.87 cm) 3.06" (7.77 cm) 3.75" (9.53 cm)

SURFACE CUT-OUT AREA FOR WALL MOUNT

Recommended cut-out area for the installation surface.

Top Panel

Figure 29. Mounting Template for 2-Gang Mud Rings (Not to Full Scale) XTP R HWP 201 Wallplate Receiver • Reference Information 32

Extron Warranty

Extron Electronics warrants this product against defects in materials and workmanship for a period of three years from the date of purchase. In the event of malfunction during the warranty period attributable directly to faulty workmanship and/or materials, Extron Electronics will, at its option, repair or replace said products or components, to whatever extent it shall deem necessary to restore said product to proper operating condition, provided that it is returned within the warranty period, with proof of purchase and description of malfunction to:

USA, Canada, South America, and Central America:

Extron U.S.A.

Electronics 1230 South Lewis Street Anaheim, CA 92805

Japan:

Extron Electronics, Japan Kyodo Building, 16 Ichibancho Chiyoda-ku, Tokyo 102-0082 Japan

Europe and Africa:

Extron Europe Hanzeboulevard 10 3825 PH Amersfoort The Netherlands

China:

Extron China 686 Ronghua Road Songjiang District Shanghai 201611 China

Asia:

Extron Asia Pte Ltd 135 Joo Seng Road, #04-01 PM Industrial Bldg. Singapore 368363 Singapore

Middle East:

Extron Middle East Dubai Airport Free Zone F13, PO Box 293666 United Arab Emirates, Dubai This Limited Warranty does not apply if the fault has been caused by misuse, improper handling care, electrical or mechanical abuse, abnormal operating conditions, or if modifications were made to the product that were not authorized by Extron.

NOTE: If a product is defective, please call Extron and ask for an Application Engineer to receive an RA (Return Authorization) number. This will begin the repair process.

USA

: 714.491.1500 or 800.633.9876

Asia

: 65.6383.4400

Europe

: 31.33.453.4040

Japan

: 81.3.3511.7655 Units must be returned insured, with shipping charges prepaid. If not insured, you assume the risk of loss or damage during shipment. Returned units must include the serial number and a description of the problem, as well as the name of the person to contact in case there are any questions. E xtron Electronics makes no further warranties either expressed or implied with respect to the product and its quality, performance, merchantability, or fitness for any particular use. In no event will Extron Electronics be liable for direct, indirect, or consequential damages resulting from any defect in this product even if Extron Electronics has been advised of such damage.

Please note that laws vary from state to state and country to country, and that some provisions of this warranty may not apply to you.

Extron Headquarters

+1.800.633.9876 (Inside USA/Canada Only) Extron USA - West +1.714.491.1517 FAX Extron USA - East +1.714.491.1500 +1.919.850.1000 +1.919.850.1001 FAX

Extron Europe

+800.3987.6673 (Inside Europe Only) +31.33.453.4040 +31.33.453.4050 FAX

Extron Asia

+65.6383.4400

+65.6383.4664 FAX

Extron Japan

+81.3.3511.7655

+81.3.3511.7656 FAX

Extron China

+86.21.3760.1568 +86.21.3760.1566 FAX

Extron Middle East

+971.4.299.1800

+971.4.299.1880 FAX © 2017 Extron Electronics All rights reserved.

www.extron.com

Extron Australia

+61.8.8113.6800

+61.8.8351.2511 FAX

Extron India

1800.3070.3777 Inside India Only +91.80.3055.3777 +91.80.3055.3737 FAX

Contact Information

Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement