Silicon Labs UG126 User's Guide

Silicon Labs UG126 User's Guide

UG126: EFM8LB1-SLSTK2030A User's Guide

The EFM8LB1-SLSTK2030A is an excellent starting point to get familiar with the EFM8 Laser Bee microcontrollers.

The kit contains sensors and peripherals demonstrating some of the MCU's many capa bilities. The kit can also serve as a starting point for application development.

The kit includes the following: • EFM8LB1 Laser Bee Starter Kit Board • 1 x CR2032 battery • Getting Started card • 1 x mini USB cable

KEY FEATURES

• EFM8LB12F64E MCU with 64 kB Flash and 4 kB RAM.

• 20-pin expansion header.

• Power sources include USB and CR2032 battery.

• 2 user buttons, 1 tri-color LED.

• 8-direction joystick.

• Ultra low power 128x128 pixel Memory LCD.

silabs.com

| Building a more connected world.

Rev. 0.6

UG126: EFM8LB1-SLSTK2030A User's Guide

Getting Started

1. Getting Started

Hardware

To set up the hardware for the EFM8LB1-SLSTK2030A kit: 1. Provide power to the board by connecting the USB connector to the PC using the provided USB cable.

2. Move the switch to the Advanced Energy Monitor (AEM) position.

Figure 1.1. Hardware Setup Software

The first step to get started with your new EFM8LB1-SLSTK2030A is to go to http://www.silabs.com/simplicity The Simplicity Studio software package contains all the tools, drivers, software examples and documentation needed to use the EFM8LB1 Starter Kit. The board comes pre-loaded with a default application, Function Generator, to interact with while the software downloads.

After downloading the latest version of Simplicity Studio and installing: 1. Select the J-Link adapter for the kit under [

Devices

].

2. Click one of the demos available under [

Getting Started

]>[

Demos

] or click the [

Getting Started

]>[

Demos

]>[

View All

] to view the entire list of available demos.

3. Click the [

Function Generator

] demo and click [

Start

] to download and run the demo.

Additional demos showcasing the various features of the EFM8 are also available in Simplicity Studio.

silabs.com

| Building a more connected world.

Rev. 0.6 | 2

2. Kit Block Diagram

An overview of the EFM8LB1 Starter Kit is shown in the figure below.

UG126: EFM8LB1-SLSTK2030A User's Guide

Kit Block Diagram POWER Board Controller UART

EFM8LB1 Microcontroller

Joystick

Figure 2.1. EFM8LB1-SLSTK2030A Block Diagram silabs.com

| Building a more connected world.

Rev. 0.6 | 3

UG126: EFM8LB1-SLSTK2030A User's Guide

Kit Hardware Layout

3. Kit Hardware Layout

The layout of the EFM8LB1 Starter Kit is shown below.

Kit USB Connector 128x128 Pixel Memory LCD Debug IN/OUT Connector Reference Board Connector Direct Debug Connector EFM8LB1 MCU Expansion Header CR2032 Battery Holder EFM8 Reset Button Power Source Select User Push Buttons User LED Joystick

Figure 3.1. EFM8LB1-SLSTK2030A Hardware Layout

The EFM8 device on the kit is connected to several peripherals. The table below shows all of the external connections to the MCU.

Table 3.1. Kit MCU Connections MCU Port Pin

P0.0

P0.1

P0.2

P0.3

P0.4

P0.5

P0.6

P0.7

P1.0

P1.1

P1.2

P1.3

P1.4

P1.5

P1.6

silabs.com

| Building a more connected world.

Port Pin Assigned Function

GPIO GPIO Port Match Input Port Match Input UART0 TX UART0 RX SPI0 SCK SPI0 MISO SPI0 MOSI SPI0 NSS SMBus0 SDA SMBus0 SCL PCA0 CEX0 PCA0 CEX1 PCA0 CEX2

Primary Board Connec tion Secondary Board Con nection

VREF Caps AGND Push Button 0 (PB0) Push Button 1 (PB1) BC - UART_TX BC - UART_RX DISP - SPI CLK

1

SPI CLK DISP - SPI MOSI I2C SDA I2C SCL RGB LED0 RGB LED1 RGB LED2 SPI MISO SPI MOSI SPI CS BC - REFCLK BC - 1 kHz SINE

Expansion Port Con nection (EXP)

EXP8 EXP6 EXP4 EXP10 EXP16 EXP15 Rev. 0.6 | 4

UG126: EFM8LB1-SLSTK2030A User's Guide

Kit Hardware Layout

MCU Port Pin

P1.7

P2.0

P2.1

P2.2

P2.3

P2.4

Port Pin Assigned Function

ADC / CMP UART1 TX UART1 RX GPIO GPIO GPIO

Primary Board Connec tion

Joystick UART1 TX UART1 RX BC - Enable DAC LOOPBACK0

Secondary Board Con nection Expansion Port Con nection (EXP)

EXP12 EXP14 EXP3 EXP13 P2.5

P2.6

P3.0

P3.1

P3.2

GPIO GPIO GPIO GPIO GPIO DISP - SPI CS DAC LOOPBACK1 UFL ADC INPUT EXP5 EXP7 EXP9 EXP11 P3.3

P3.4

GPIO GPIO DISP - Enable P3.7 / C2D C2D (for debug)

Note:

1. This signal has high loading. If the MCU pin is used for signals where edge speed is critical, this signal should be disconnected from the pin.

silabs.com

| Building a more connected world.

Rev. 0.6 | 5

UG126: EFM8LB1-SLSTK2030A User's Guide

Power Supply and Reset

4. Power Supply and Reset

4.1 MCU Power Selection

The Laser Bee MCU on the EFM8LB1-SLSTK2030A is designed to be powered by three different sources: • Through the on-board debugger.

• By a 3 V Battery.

• An externally supplied power source.

Selecting the power source is done with the slide switch in the lower left corner of the board. The figure shows how the different power sources can be selected with the slide switch.

Figure 4.1. EFM8LB1-SLSTK2030A Power Switch

With the switch in the AEM position, an on-board low noise LDO with a fixed output voltage of 3.3 V is used to power the MCU. This LDO is powered from the "J-Link" USB cable.

With the switch in the BAT position, the device may be powered from either a 20 mm coin cell battery (in the CR2032 socket) or an external power supply (connected to the VMCU and GND pins on the expansion header).

4.2 MCU Reset

The EFM8 MCU can be reset by a few different sources: • The RESET button.

• An external debugger by pulling the RSTb pin low.

silabs.com

| Building a more connected world.

Rev. 0.6 | 6

UG126: EFM8LB1-SLSTK2030A User's Guide

Peripherals

5. Peripherals

The starter kit has a set of peripherals that showcase some of the features of the EFM8 Laser Bee microcontroller.

Be aware that most EFM8 I/O routed to peripherals are also routed to the breakout pads. This must be taken into consideration when using the breakout pads for your application.

5.1 Push Buttons and LEDs

The kit has two user push buttons. They are connected to the EFM8, and are debounced by RC filters with a time constant of 1 ms. The buttons are connected to pins P0.2 and P0.3.

In addition to the two push buttons, the kit also features a tri-color LED that is controlled by EFM8 GPIO. The LED is connected to pins P1.4, P1.5, and P1.6 in an active-low configuration.

Figure 5.1. Buttons/LEDs silabs.com

| Building a more connected world.

Rev. 0.6 | 7

UG126: EFM8LB1-SLSTK2030A User's Guide

Peripherals

5.2 Joystick

The kit has an analog joystick with 8 measureable positions. This joystick is connected to the EFM8 on the P1.7 pin and uses different resistor values to create voltages measurable by the ADC0.

Figure 5.2. Joystick Table 5.1. Joystick Resistor Combinations Direction Resistors Combinations (kΩ)

Center press Up (N) Up-Right (NE) 0.1

0.1 + 10 60.4

60.4 + 10 (

N

(

N

// //

E

)

E

) + 10 = 21.34

21.34 + 10 Right (E) Down-Right (SE) Down (S) Down-Left (SW) 33 33 + 10 (

S

(

S

// //

E

)

E

) + 10 = 7.67

7.67 + 10 10 10 + 10 (

S

(

S

// //

W

)

W

) + 10 = 6 6 + 10 Left (W) Up-Left (NW) (

N

(

N

// //

W W

) ) + 10 = 12.01

12.01 + 10

Note:

1. These calculated values assume a VMCU of 3.3 V.

15 15 + 10

Expected UIF_JOYSTICK Voltage (V) 1

0.033

2.831

2.247

2.533

1.433

1.650

1.238

1.980

1.801

silabs.com

| Building a more connected world.

Rev. 0.6 | 8

UG126: EFM8LB1-SLSTK2030A User's Guide

Peripherals

5.3 Memory LCD-TFT Display

A 1.28-inch SHARP Memory LCD-TFT has been added to the board to enable interactive applications to be developed. The display has a high resolution of 128 by 128 pixels and consumes very little power. It is a reflective monochrome display, so each pixel can only be light or dark, and no backlight is needed in normal daylight conditions.

The display interface consists of an SPI-compatible serial interface and some extra control signals. Data are sent to the display one line (128 bits) at a time.

The Memory LCD-TFT display is shared with the kit Board Controller, allowing the Board Controller application to display useful infor mation when the user application is not using the display. The EFM8 MCU always controls ownership of the display using the EFM_DISP_ENABLE signal: • 0: The Board Controller has control of the display.

• 1: The user application (EFM8) has control of the display.

Data are clocked in on EFM_DISP_MOSI (P1.0) when EFM_DISP_CS (P2.6) is high, and the clock is sent on EFM_DISP_SCLK (P0.6). The maximum supported clock speed is 1 MHz.

Please refer to the display application information for details on driving the display: http://www.sharpmemorylcd.com/1-28-inch-memory-lcd.html

P0.6 (SPI0) P1.0 (SPI0) P2.6 (GPIO) P3.4 (GPIO) 8 EFM_DISP_ENABLE 0: BC controls display 1: EFM controls display

Figure 5.3. 128x128 Pixel Memory LCD silabs.com

| Building a more connected world.

Rev. 0.6 | 9

UG126: EFM8LB1-SLSTK2030A User's Guide

Connectors

6. Connectors

6.1 Breakout Pads

Many of the EFM8's pins are routed out to "breakout pads" at the top and bottom edges of the kit. A 2.54 mm pitch pin header can be soldered in for easy access to these pins. Most I/O pins are available, with the exception of pins used to drive the LCD.

Note:

Some of the breakout pads are shared by on-board EFM peripherals. The schematic must be consulted to make sure that it is acceptable to use a shared pin in your application.

silabs.com

| Building a more connected world.

Figure 6.1. Breakout Pads and Expansion Header

Rev. 0.6 | 10

UG126: EFM8LB1-SLSTK2030A User's Guide

Connectors

6.2 Expansion Header

On the right hand side of the board an angled 20-pin expansion header is provided to allow connection of peripherals or plugin boards.

The connecter contains a number of I/O pins that can be used with most of the Laser Bee's features. Additionally, the VMCU, 3V3 and 5V power rails are also exported.

The figure below shows the pin assignment of the expansion header. With the exception of a few pins, most of the expansion header's pins are the same as those on the EFM32 Gecko or EFM32 Tiny Gecko starter kits.

Figure 6.2. Expansion Header

Some of the chip peripheral functions that are available on the expansion header are listed in the table below.

Table 6.1. Some Peripheral Functions Available on Expansion Header Peripheral Peripheral pin MCU Pin

UART1 SPI0 SMBus I2CSLAVE0 ADC0 Comparator 0 Comparator 1 UART1 TX UART1 RX SPI0 SCK SPI0 MISO SPI0 MOSI SPI0 CS SMBus0 SDA SMBus0 SCL I2CSLAVE0 SDA I2CSLAVE0 SCL Input CNVSTR P2.0

P2.1

P0.6

P0.7

P1.0

P1.1

P1.2

P1.3

P2.0

P2.1

Any supported pin (see Reference Manual for more information) P0.6

CMP0P Positive Input Any supported pin (see Reference Manual for more information) CMP0N Negative In put Any supported pin (see Reference Manual for more information) CMP1P Positive Input Any supported pin (see Reference Manual for more information) CMP1N Negative In put Any supported pin (see Reference Manual for more information)

silabs.com

| Building a more connected world.

6 4 10 16 15

EXP Header pin number

12 14 8 12 14 Multiple 8 Multiple Multiple Multiple Multiple Rev. 0.6 | 11

UG126: EFM8LB1-SLSTK2030A User's Guide

Connectors

Note:

This table only sums up some of the alternate functions available on the expansion header. Consult the EFM8LB12F64E data sheet for a complete list of alternate functions.

6.3 Debug Connector

This connector is used for Debug In and Debug Out (see chapter on Debugging).

Pin num ber

1

Function

VTARGET 8 9 2 4 6 TMS/SWDIO/C2D TCK/SWCLK/C2CK TDO/SWO TDI ATTACH 10 12 14, 16, 18, 20 11, 13 3, 5, 15, 17, 19 #RESET TRACECLK TRACED0-3 NC GND

Figure 6.3. Debug Connector Table 6.2. Debug Connector Pinout Note

Target voltage on the debugged application.

Note:

This connection is required and is needed for the debug circuitry to match voltage levels with the target device.

JTAG TMS, Serial Wire data I/O, or EFM8 C2 data I/O JTAG TCK, Serial Wire clock, or EFM8 C2 clock JTAG TDO or Serial Wire Output JTAG data in This signal must be pulled to ground by the external debugger or application for cable insertion detection.

Target MCU reset.

Trace clock Trace data (4 lines) Not Connected

silabs.com

| Building a more connected world.

Rev. 0.6 | 12

UG126: EFM8LB1-SLSTK2030A User's Guide

Connectors

6.4 Direct Debug Connector

This connector (J103) is used for directly debugging the EFM8 using an external debug adapter (see chapter on Debugging). This is especially useful for debugging the MCU on the STK board when the part is battery powered or powered by an external supply.

2 3

Pin number

1

Function

C2CK C2D GND

Figure 6.4. Direct Debug Connector Table 6.3. Direct Debug Connector Pinout Note

EFM8 C2 clock EFM8 C2 data I/O

6.5 Reference Board

The top-right corner of the board includes a 20-pin reference board connector. The connecter contains some I/O pins that can be used with some of the EFM8 Laser Bee's features. Additionally, the 3V3 and 5V power rails are also exported.

The figure below shows the pin assignment of the reference board header.

Figure 6.5. Reference Board Header silabs.com

| Building a more connected world.

Rev. 0.6 | 13

7. Integrated Development Environment

UG126: EFM8LB1-SLSTK2030A User's Guide

Integrated Development Environment

Figure 7.1. Simplicity Studio

Simplicity Studio includes various examples in source form to use with the Starter Kit. To run these examples: 1. Provide power to the board by connecting the DBG USB connector to the PC using the provided USB cable.

2. Move the switch to the AEM position.

3. Select the J-Link adapter for the kit under [

Devices

].

4. Click the [

Getting Started

]>[

New Project

] button.

5. In the wizard, ensure the EFM8LB1 Laser Bee Starter Kit Board kit and click [

Next

].

6. Select [

Example

] and click [

Next

].

7. Select the desired example or demo from the list and click [

Next

].

8. Click [

Finish

].

9. Click the [

Debug

] button in the IDE to build and download the code to the hardware.

10. Follow the instructions at the top of the main example file to set up the hardware as needed.

11. Click the [

Resume

] button to start running the example.

silabs.com

| Building a more connected world.

Rev. 0.6 | 14

UG126: EFM8LB1-SLSTK2030A User's Guide

Advanced Energy Monitor

8. Advanced Energy Monitor

When the EFM8LB1 Starter Kit is connected to a Silicon Labs STK, the STK's Advanced Energy Monitor (AEM) hardware also meas ures the slstk2030a power consumption using the VMCU connection on the EXP header. By using the [

Energy Profiler

] in Simplicity Studio, current consumption and voltage can be measured in real time.

More details about AEM and its operation can be found in the STK User Guide. Note that AEM will measure the current for all circuitry connected to VMCU, including the STK MCU and the CPT device.

Figure 8.1. Measuring EFM8LB1-SLSTK2030A Current Using AEM 8.1 Usage

The AEM data is collected by the board controller and can be displayed by the energyAware Profiler, available through Simplicity Stu dio. By using the energyAware Profiler, current consumption and voltage can be measured in realtime.

silabs.com

| Building a more connected world.

Rev. 0.6 | 15

UG126: EFM8LB1-SLSTK2030A User's Guide

Advanced Energy Monitor

8.2 AEM Theory of Operation

In order to be able to accurately measure current ranging from 0.1 µA to 50 mA (114 dB dynamic range), a current sense amplifier is utilized together with a dual gain stage. The current sense amplifier measures the voltage drop over a small series resistor, and the gain stage further amplifies this voltage with two different gain settings to obtain two current ranges. The transition between these two ranges occurs around 250 µA. Digital filtering and averaging is done within the Board Controller before the samples are exported to the Energy Profiler application.

During startup of the kit, an automatic calibration of the AEM is performed. This calibration compensates for the offset error in the sense amplifiers.

Figure 8.2. Advanced Energy Monitor 8.3 AEM Accuracy and Performance

The AEM is capable of measuring currents in the range of 0.1 µA to 50 mA. For currents above 250 µA, the AEM is accurate within 0.1

mA. When measuring currents below 250 µA, the accuracy increases to 1 µA. Even though the absolute accuracy is 1 µA in the sub 250 µA range, the AEM is able to detect changes in the current consumption as small as 100 nA. The AEM produces 6250 current samples per second.

Note:

The current measurement will only be correct when powering the EFM8 from USB power through the debugger (power select switch set to DBG or AEM).

silabs.com

| Building a more connected world.

Rev. 0.6 | 16

UG126: EFM8LB1-SLSTK2030A User's Guide

Board Controller

9. Board Controller

The kit contains a board controller that is responsible for performing various board-level tasks, such as handling the debugger and the Advanced Energy Monitor. An interface is provided between the EFM8 and the board controller in the form of a UART connection. The connection is enabled by setting the EFM_BC_EN (P2.2) line high, and using the lines EFM_BC_TX (P0.4) and EFM_BC_RX (P0.5) for communicating.

The BC enable signal connects the EFM8 to the board controller: • 0: EFM8 UART pins are isolated from the Board Controller.

• 1: EFM8 UART pins are connected to the Board Controller (default upon reset).

Note:

The board controller is only available when USB power is connected.

silabs.com

| Building a more connected world.

Rev. 0.6 | 17

UG126: EFM8LB1-SLSTK2030A User's Guide

Debugging

10. Debugging

The EFM8LB1-SLSTK2030A contains an integrated debugger, which can be used to download code and debug the Laser Bee EFM8 MCU. In addition to programming the MCU on the kit, the debugger can also be used to program and debug external Silicon Labs EFM8 devices.

10.1 Debug Modes

Programming external devices is done by connecting to a target board through the provided Debug IN/OUT Connector, and by setting the debug mode to [

Out

]. The same connector can also be used to connect an external debugger to the EFM8 MCU on the kit, by setting the debug mode to [

In

]. A summary of the different supported debug modes is given in Table 10.1 Debug Modes on page 18 .

Table 10.1. Debug Modes Mode

Debug MCU Debug In

Description

In this mode the on-board debugger is connected to the EFM8 on the EFM8LB1-SLSTK2030A.

In this mode, the on-board debugger is disconnected, and an external debugger can be connected to debug the EFM8 on the EFM8LB1-SLSTK2030A.

In this mode, the on-board debugger can be used to debug an EFM8 mounted on a custom board.

Debug Out Selecting the active debug mode is done with a drop-down menu in the Kit Manager tool, which is available through Simplicity Studio.

When using the debug adapter in the [

Out

] mode, the end device must be manually detected before debugging and programming. To do this: 1. Right-click on the kit from the Simplicity Studio launch screen and select [

Select Target Part...

].

2. If needed, select the appropriate [

Target Interface

] for the external device. For example, EFM8 devices will use the [

C2

] selection.

3. In the same dialog, click the [

Detect Target

] button.

4. Click [

OK

] to close the dialog. The external target can now be debugged and programmed.

10.2 Debugging during Battery Operation

When the EFM8 is powered by battery and the J-Link USB is still connected, the on-board debug functionality is available. If the USB power is disconnected, the Debug In mode will stop working.

To enable debugging when the USB cable is removed, connect an external debugger to the MCU Debug Header in the top right corner of the EFM8LB1-SLSTK2030A instead of the Debug IN/OUT Connector. This header is connected directly to the EFM8's debug inter face. The pinout of this header is shown in the Connectors chapter.

silabs.com

| Building a more connected world.

Rev. 0.6 | 18

UG126: EFM8LB1-SLSTK2030A User's Guide

Upgrading the Kit

11. Upgrading the Kit

Upgrading the kit firmware is done through Simplicity Studio in the [

Launcher

] perspective. Simplicity Studio will automatically check for new updates on startup. After selecting a kit in the left under [

Devices

], the area at the top of the Launcher page displays the current kit version and Debug Mode. Use the links in this area to change the debug mode or upgrade the kit firmware.

silabs.com

| Building a more connected world.

Rev. 0.6 | 19

UG126: EFM8LB1-SLSTK2030A User's Guide

Schematics, Assembly Drawings, and BOM

12. Schematics, Assembly Drawings, and BOM

The schematics, assembly drawings and bill of materials (BOM) for the EFM8LB1 Starter Kit board are available through Simplicity Stu dio when the kit documentation package has been installed. These files are also available from the links below.

• • EFM8LB1 Starter Kit (STK) BOM EFM8LB1 Starter Kit (STK) Schematic

12.1 Board Revision History

• A00 — Initial prototype revision.

• A01 — Changed to surface mounted joystick and smaller reset switch.

• A02 — Cleaned up the signal generator circuit and updated silk print.

• A03 — Updated EFM8LB1 device revision and adjusted the reset switch.

• A04 — Changed D801 to “not mounted”. Changed X900 to KDS DSX321G.

• A05 — Updated EFM8LB1 device revision.

A00 Revision Boards

There are no known issues with the A00 boards.

A01 Revision Boards

There are no known issues with the A01 boards.

A02 Revision Boards

There are no known issues with the A02 boards.

A03 Revision Boards

There are no known issues with the A03 boards.

A04 Revision Boards

There are no known issues with the A04 boards.

A05 Revision Boards

There are no known issues with the A05 boards.

silabs.com

| Building a more connected world.

Rev. 0.6 | 20

13. Revision History

Revision 0.6

February, 2019

• Updated 12.1 Board Revision History for Rev A05

Revision 0.5

April, 2018

• Updated 6.1 Breakout Pads

with the correct pin numbers for J101 and J102.

• Updated 12.1 Board Revision History for Rev A04.

Revision 0.4

January, 2018

• Updated 6.2 Expansion Header with the correct pin label for EXP13.

Revision 0.3

June, 2016 • Updated screenshots and instructions for Simplicity Studio v4.

• Added 12.1 Board Revision History .

• Added the UG126 document reference.

• Added a note to

6.3 Debug Connector that VTARGET is required.

• Added the reference for the direct debug connector to

6.4 Direct Debug Connector .

• Added a note about high loading on the DISP CLK signal.

Revision 0.2

September, 2015 • Updated board pictures.

Revision 0.1

April, 2015 • Initial revision.

UG126: EFM8LB1-SLSTK2030A User's Guide

Revision History

silabs.com

| Building a more connected world.

Rev. 0.6 | 21

Simplicity Studio

One-click access to MCU and wireless tools, documentation, software, source code libraries & more. Available for Windows, Mac and Linux!

IoT Portfolio

www.silabs.com/IoT

SW/HW

www.silabs.com/simplicity

Quality

www.silabs.com/quality

Support and Community

community.silabs.com

Disclaimer

Silicon Labs intends to provide customers with the latest, accurate, and in-depth documentation of all peripherals and modules available for system and software implementers using or intending to use the Silicon Labs products. Characterization data, available modules and peripherals, memory sizes and memory addresses refer to each specific device, and "Typical" parameters provided can and do vary in different applications. Application examples described herein are for illustrative purposes only. Silicon Labs reserves the right to make changes without further notice to the product information, specifications, and descriptions herein, and does not give warranties as to the accuracy or completeness of the included information. Without prior notification, Silicon Labs may update product firmware during the manufacturing process for security or reliability reasons. Such changes will not alter the specifications or the performance of the product. Silicon Labs shall have no liability for the consequences of use of the information supplied in this document. This document does not imply or expressly grant any license to design or fabricate any integrated circuits. The products are not designed or authorized to be used within any FDA Class III devices, applications for which FDA premarket approval is required or Life Support Systems without the specific written consent of Silicon Labs. A "Life Support System" is any product or system intended to support or sustain life and/or health, which, if it fails, can be reasonably expected to result in significant personal injury or death. Silicon Labs products are not designed or authorized for military applications. Silicon Labs products shall under no circumstances be used in weapons of mass destruction including (but not limited to) nuclear, biological or chemical weapons, or missiles capable of delivering such weapons. Silicon Labs disclaims all express and implied warranties and shall not be responsible or liable for any injuries or damages related to use of a Silicon Labs product in such unauthorized applications.

Trademark Information

Silicon Laboratories Inc.® , Silicon Laboratories®, Silicon Labs®, SiLabs® and the Silicon Labs logo®, Bluegiga®, Bluegiga Logo®, Clockbuilder®, CMEMS®, DSPLL®, EFM®, EFM32®, EFR, Ember®, Energy Micro, Energy Micro logo and combinations thereof, "the world’s most energy friendly microcontrollers", Ember®, EZLink®, EZRadio®, EZRadioPRO®, Gecko®, Gecko OS, Gecko OS Studio, ISOmodem®, Precision32®, ProSLIC®, Simplicity Studio®, SiPHY®, Telegesis, the Telegesis Logo®, USBXpress® , Zentri, the Zentri logo and Zentri DMS, Z-Wave®, and others are trademarks or registered trademarks of Silicon Labs. ARM, CORTEX, Cortex-M3 and THUMB are trademarks or registered trademarks of ARM Holdings. Keil is a registered trademark of ARM Limited. Wi-Fi is a registered trademark of the Wi-Fi Alliance. All other products or brand names mentioned herein are trademarks of their respective holders.

Silicon Laboratories Inc.

400 West Cesar Chavez Austin, TX 78701 USA

http://www.silabs.com

Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement