Silicon Labs QSG104 Quick Start Guide

Silicon Labs QSG104 Quick Start Guide
QSG104
EM34 X FULL-FEATURE REMOTE EVALUATION KIT
QUICK-START GUIDE
Unpacking the Contents
ATTENTION: Observe precautions for handling electrostatic sensitive devices.
Remove components from their packaging:
Silicon Labs EM341 Full-Feature Remote Control (1)
DEI (Data Emulation Interface) Cable (1)
Ember® Debug Adapter (ISA3) (1)
Ethernet Cable (1)
Telegesis USB Stick
USB Cable (1)
Packet Trace Port Cable (1)
AA Batteries (2)
Packet Trace Header Connector (1)
Software Serial Number
Rev 0.1
Copyright © 2015 by Silicon Laboratories
QSG104
QSG104
The EM34x Full-Feature Remote Evaluation kit provides the hardware and software necessary to demonstrate the
functionality of the Silicon Labs Full Feature Remote Control. Access to software tools required to customize your
own remote control application is also provided.
Kit Use Options
The EM34xx Full Feature Remote Evaluation Kit offers you two ways of using and testing the Full-Feature remote:
•
•
Full-Feature Remote Control Demonstration: An out-of-the-box demonstration of the remote’s features,
without further setup. See section 1, Running the Full Feature Remote Control Demonstration, for more
information. Only the remote control, batteries, and USB stick are required for the demonstration.
Custom Application Development: The ability to customize, compile, load, and run your own controller
application, based on Silicon Labs reference designs. See section 2, Custom Application Development, for
more information.
1 Running the Full Feature Remote Control Demonstration
The EM34x Full Feature Remote Evaluation Kit comes with the tools and software needed to test the remote’s
functionality out of the box. The Full Feature Remote comes pre-programmed with an example ZigBee Remote
Control (ZRC) controller application. The USB stick contains an EM3588 chip preprogrammed with an example
ZRC target application designed to show some of the remote’s functionality. Demonstration software allows you to
see packet transfer data from the controller to the target, button presses, and to hear voice recordings transmitted
from the remote.
1. Download the RF4CE_Demo_Release.zip file from the www.silabs.com/zrctraining page.
2. Unzip the file to a location of your choice.
3. Install the USB stick driver from the RF4CE_Demo_Release\Windows\Driver\EM358CDCDriverInstaller
folder created in step 2.
4. Plug the USB stick into a port on your computer.
5. Insert the batteries into the remote.
6. Launch the RF4CE_Remote_Demo application from the RF4CE_Demo_Release\Windows directory
created in step 2.
2
Rev. 0.1
QSG104
7.
8.
9.
10.
In the Select Remote drop down list, select [Universal Electronics].
Select the USB stick’s port. It will be assigned to a COM port.
Click [Pair] to initiate the pairing process.
On the remote, press and hold both the [SET] (small button on the upper left) and [STB] buttons. Release
both buttons when the LED on the remote turns red. The LED will remain red while the remote is
searching for a target device.
11. Once pairing is completed, the LED on the remote will turn off.
12. To verify the devices paired successfully, press a button on the remote and the corresponding button on
the application remote graphic will turn green.
Rev. 0.1
3
QSG104
To demonstrate the remote locator functionality:
1. In the demonstration application, click [Find Me]. The remote will beep and the lights will flash for a period
of time. There may be a delay between clicking [Find Me] in the application and the remote
acknowledgement due to the polling time of the remote.
To demonstrate voice functionality:
1. In the demonstration application, make sure the Audio Data drop down is set to [Hardware Codec
Settings].
2. On the remote, press and hold the [VOICE] button and speak. Release the [VOICE] button when you are
done.
The remote wireless streams your voice to the USB device, where it is processed and stored as a .WAV
file. All .WAV files on the USB device are listed under Audio Data.
3. To hear your recorded audio as it streamed to the target, in the application check [Play Audio Real Time
Over Speakers].
4. To play a file, click the file in the list and click [Play Selected].
5. To clear all files from the USB device, click [Clear Audio].
2 Custom Application Development
You must be a registered user of the Silicon Labs Technical Support Portal and the EM34x Full-Feature Remote
Evaluation Kit must be registered to obtain support and download the latest Silicon Labs development software and
stacks. Go to www.silabs.com/zrctraining and follow the instructions to register your kit.
Note:
Your software serial number will be in the form xxxx-xxxx-xxxx-xxxx-xxxx and can be found on Hardware
Identification List label.
To download the development software, after you have completed registration and are logged into the Silicon Labs
support page click the Software Releases tab, select [latest EmberZNet Software] from the drop-down menu,
and sort by Release Date.
Download and install the latest version of the following tools. The release notes installed with the EmberZNet stack
software include more detailed installation instructions and required version numbers.
•
•
•
•
EmberZNet
Ember Desktop
ISA3 Utilities
IAR Embedded Workbench for ARM (IAR-EWARM), installed through the IAR website
Licenses and support for IAR are provided separately and can be obtained from IAR Systems at
http://www.iar.com.
An evaluation version of IAR can be downloaded directly at:
ftp://files.iar.com/pub/silabs/EWARM-7301.exe
For more information on developing with the EM34x kits, refer to UG113, EM34x Development Kit User's Guide.
See QSG105, Getting Started with Silicon Labs Wireless Networking Software, for information on how to configure
and compile your own applications. See AN906, RF4CE ZigBee Remote Control Firmware Guide, for details on the
reference designs. These and other useful documents are installed with the EmberZNet software. You can also use
the Silicon Labs Technical Support Portal at www.silabs.com/support.
4
Rev. 0.1
QSG104
CONTACT INFORMATION
Silicon Laboratories Inc.
400 West Cesar Chavez
Austin, TX 78701
Tel: 1+(512) 416-8500
Fax: 1+(512) 416-9669
Toll Free: 1+(877) 444-3032
For additional information please visit the Silicon Labs Technical Support page: http://www.silabs.com/support
Patent Notice
Silicon Labs invests in research and development to help our customers differentiate in the market with innovative low-power, small size,
analog-intensive mixed-signal solutions. Silicon Labs' extensive patent portfolio is a testament to our unique approach and world-class
engineering team.
The information in this document is believed to be accurate in all respects at the time of publication but is subject to change without notice.
Silicon Laboratories assumes no responsibility for errors and omissions, and disclaims responsibility for any consequences resulting from the
use of information included herein. Additionally, Silicon Laboratories assumes no responsibility for the functioning of undescribed features or
parameters. Silicon Laboratories reserves the right to make changes without further notice. Silicon Laboratories makes no warranty,
representation or guarantee regarding the suitability of its products for any particular purpose, nor does Silicon Laboratories assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation
consequential or incidental damages. Silicon Laboratories products are not designed, intended, or authorized for use in applications intended to
support or sustain life, or for any other application in which the failure of the Silicon Laboratories product could create a situation where personal
injury or death may occur. Should Buyer purchase or use Silicon Laboratories products for any such unintended or unauthorized application,
Buyer shall indemnify and hold Silicon Laboratories harmless against all claims and damages.
Silicon Laboratories, Silicon Labs, and Ember are registered trademarks of Silicon Laboratories Inc.
Other products or brandnames mentioned herein are trademarks or registered trademarks of their respective holders.
Rev. 0.1
5
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement