Vivitek DK8500Z Projector Manual

Vivitek DK8500Z Projector Manual
Remote Communicaton
Manual
DK8500Z
DK8500Z DLP Projector Remote Communication Manual
Table of Contents
The RS-232 Serial Interface Commands ...................................................................................... 2
Communication parameter ......................................................................................................................................... 2
Operation commands................................................................................................................................................. 2
Operation command syntax ................................................................................................................................ 2
List of operation commands ............................................................................................................................... 3
Simulated IR remote controller commands.............................................................................................................. 14
Control the Projector Through a Network.................................................................................. 15
Cable connection ..................................................................................................................................................... 15
Set up the projector for networking .......................................................................................................................... 16
Control the projector through a network .................................................................................................................. 17
Control the projector through a web browser ................................................................................................... 17
Control projector with TCP/IP communication protocol .................................................................................... 23
About Vivitek Support ................................................................................................................. 24
1
RM85001117EN00
DK8500Z DLP Projector Remote Communication Manual
The RS-232 Serial Interface Commands
This projector supports with two existing types of RS-232 serial commands:
 Operation command: Available menu options are INPUT, PICTURE, ALIGNMENT, CONTROL and SERVICE.
 Simulated IR remote controller commands: Controls projector via RS-232 command, thus the commands simulate
IR remote controller and its control keys.
Communication parameter
You can use the serial control command to input commands for projector control or retrieve its operational data
through Windows client terminal software, e.g. Hyper Terminal, with ASCII characters. You need to set up the following
communication parameters in advance:
Item
Parameter:
Bit per Second
9600 bps
Data Bit
8-bit
Parity
None
Stop Bit
1
Flow Control
None
Port
7000
Note:
 The terminal software does not return every command input character
 The transmission performance varies with the length of RS-232 cable
Operation commands
Operation command syntax
An operation command is prefixed by character "op", followed by control commands and settings separated by
space blank [SP], and ended by carriage return pair "CR" and "ASCII hex 0D".Syntax of serial control
commands:
op[SP]<operation command>[SP]<Setting Value>[CR]
op
[SP]
[CR]
Setting value
:
:
:
:
A constant indicating this is an operation command.
Indicate one blank space.
Indicate the command ending carriage return pair "CR" and "ASCII hex 0D".
Settings of operation command
Types of setup strings
Query current setup
Setup
Increase setup order of
adjustment items
Decrease setup order of
adjustment items
Execute operation command
Characters of settings
?
= <settings>
+
None
Description
Question mark "?" indicates querying current setup
Syntax: Symbol "=" suffixed with setup values
Some settings are changed in steps. Symbol "+"
indicates changing one step up
Some settings are changed in steps. Symbol "-"
indicates changing one step down
Certain operation commands execute after input
without further setting or regulators.
Examples:
Control items
Input command
Projector return message
Query current brightness
op bright ? [CR]
OP BRIGHT = 101
Set up brightness
op bright = 127 [CR]
OP BRIGHT = 127
Set up input signal source to
op input.sel = 0 [CR] OP INPUT.SEL = 0
HDMI
Reset projection lens to
lens.center
center position
Note:
 When sending multiple commands, make sure the return message of the last command is received
before sending out the next one.
2
RM85001117EN00
DK8500Z DLP Projector Remote Communication Manual
List of operation commands
INPUT
OSD Function
Operation
command
Input Select
input.sel
Settings/Return Values
Note
?
=
0 = HDMI 1
1 = HDMI 2
3 = HDBaseT
4 = 3G-SDI
 Not applicable when the project is at
standby mode
PIP/PIP Option
pip
?
=
0 = Off
1 = On
 Not applicable when the project is at
standby mode and 3D mode
PIP/PIP Input
pip.sel
?
=
 Not applicable when the project is at
standby mode or PIP option is set to
Off.
PIP/ Position
pip.pos
?
=
0 = HDMI 1
1 = HDMI 2
3 = HDBaseT
4 = 3G-SDI
0 = Top Left
1 = Top Right
2 = Bottom Left
3 = Bottom Right
4 = PBP
Auto Source
auto.src
?
=
0 = Off
1 = On
 Not applicable when the projector is
at standby mode.
Auto Sync
Auto.mg
(execute)
 Available when source is locked.
Color Space
color.space
?
=
0 = Auto
1 = YPbPr (Rec. 709)
2 = YcbCr (Rec. 601)
3 = RGB-PC (0-255)
4 = RGB-Video (16-235)
 Available when source is locked.
Aspect Ratio
aspect
?
=
0 = 5:4
1 = 4:3
2 = 16:10
3 = 16:9
4 = 1.88
5 = 2.35
6 = LetterBox
7 = Source
8 = Native
 Available when the source is locked.
VGA Setup/H Total
h.total
?
=
+
?
=
+
?
=
+
-
VGA Setup/H Start
h.pos
VGA Setup/H Phase
h.phase
VGA Setup/V Start
v.pos
?
=
+
-
0-200
 Available when the source is locked
Or Input source is VGA or
Component(RGBHV)
0-200
 Available when the source is locked
Or Input source is VGA or
Component(RGBHV)
0-200
 Available when the source is locked.
 Input source is VGA or
Component(RGBHV)
0-200
 Available when the source is locked.
 Input source is VGA or
Component(RGBHV)
3
RM85001117EN00
 Not applicable when the project is at
standby mode or PIP is set to Off.
DK8500Z DLP Projector Remote Communication Manual
OSD Function
Test Pattern
Operation
command
pattern
3D/3D Format
3d.format
3D/Eye Swap
3d.swap
3D/DLP Link
3d.dlplink
3D/Dark Time
3d.darktime
3D/sync delay
3d.syncdelay
3D/Sync Reference
3d.syncref
PICTURE
OSD Function
Picture Mode
Operation
command
pic.mode
Brightness
bright
Contrast
contrast
Saturation
saturat
Hue
tint
Sharpness
sharp
Settings/Return Values
?
=
0 = Off
1 = CrossHatch
2 = Color Bar
3 = Checkboard
4 = H Burst
5 = V Burst
6 = White
7 = Red
8 = Green
9 = Blue
10 = Black
= ? 0 = Off
1 = Auto
2 = Side-By-Side (Half)
3 = Top-And-Bottom
4 = Frame Sequential
 Not applicable when the project is at
standby mode.

Not applicable when the project is at
standby model.
= ? 0 = Normal
1 = Reverse
= ? 0 = Off
1 = On

Applicable when the projector is at
3D mode.
Applicable when 3D.Darktime is set
to 2 (1.95ms)
= ? 0 = 0.65 ms
1 = 1.3 ms
2 = 1.95 ms
= ? 1 – 60

Applicable when the projector is at
3D mode.

Applicable when the projector is at
3D mode.
= ? 0 = External
1 = Internal
2 = Auto

Not applicable when the project is at
standby mode.
Settings/Return Values
?
=
?
=
+
?
=
+
?
=
+
-?
=
+
?
=
+
-

Note
0 = High Bright
1 = Presentation
2 = Video
0-200
 Not applicable when the project is at
standby mode.
0-200
 Not applicable when the project is at
standby mode or the input signal is
not locked yet.
0-200
 Apply for YUV signal input
 Not applicable if the input signal is
not locked yet.
0-200
 Apply for YUV signal input
 Not applicable if the input signal is
not locked yet.
0-10
 Not applicable when the project is in
standby mode or the input signal is
not locked yet.
4
RM85001117EN00
Note
 Not applicable when the project is at
standby mode or the input signal is
not locked yet.
DK8500Z DLP Projector Remote Communication Manual
OSD Function
Noise Reduction
Operation
command
nr
Settings/Return Values
Note
?
=
+
-
0 = Off
1 = Low
2 = Middle
3 = High
 Not applicable when the project is at
standby mode.
Color Temperature
color.temp
?
=
0 = 5400K
1 = 6500K
2 = 7500K
3 = 9300K
4 = Native
 Not applicable at 3D mode
Gamma
gamma
?
=
 Not applicable when the project is at
standby mode or the input signal is
not locked yet.
Overscan
zoom
?
=
0 = 1.0
1 = 1.8
2 = 2.0
3 = 2.2
4 = 2.35
5 = 2.5
6 = S-Curve
7 = DICOM
8 = HDR-PQ400
9 = HDR-PQ500
10 = HDR-PQ1000
11 = HDR-HLG
0 = Off
1 = Crop
2 = Zoom
Input Balance /Red
Offset
red.offset
0-200
 Available when the input source is
locked.
Input Balance /Green
Offset
green.offset
0-200
 Available when the input source is
locked.
Input Balance /Blue
Offset
blue.gain
0-200
 Available when the input source is
locked.
Input Balance /Red
Gain
red.gain
0-200
 Available when the input source is
locked.
Input Balance /Green
Gain
green.gain
0-200
 Available when the input source is
locked.
Input Balance /Blue
Gain
blue.gain
0-200
 Available when the input source is
locked.
HSG/Red Gain
hsg.r.gain
?
=
+
?
=
+
?
=
+
?
=
+
?
=
+
?
=
+
?
=
+
-
0-200
 Available when the input source is
locked.
5
RM85001117EN00
 Not applicable when the project is at
standby mode or the input signal is
not locked yet.
DK8500Z DLP Projector Remote Communication Manual
OSD Function
HSG/Green Gain
Operation
command
hsg.g.gain
HSG/Blue Gain
hsg.b.gain
HSG/Cyan Gain
hsg.c.gain
HSG/Magenta Gain
hsg.m.gain
HSG/Yellow Gain
hsg.y.gain
HSG/Red/Saturation
hsg.r.sat
HSG/Green/Saturation
hsg.g.sat
HSG/Blue/Saturation
hsg.b.sat
HSG/Cyan/Saturation
hsg.c.sat
HSG/Magenta/
Saturation
hsg.m.sat
HSG/Yellow/Saturation
Hsg.y.sat
HSG/Red/Hue
hsg.r.hue
HSG/Green/Hue
hsg.g.hue
HSG/Blue/Hue
Hsg.b. hue
Settings/Return Values
?
=
+
?
=
+
?
=
+
?
=
+
?
=
+
?
=
+
?
=
+
?
=
+
?
=
+
?
=
+
?
=
+
?
=
+
?
=
+
?
=
+
-
0-200
 Available when the input source is
locked.
0-200
 Available when the input source is
locked.
0-200
 Available when the input source is
locked.
0-200
 Available when the input source is
locked.
0-200
 Available when the input source is
locked.
0-200
 Available when the input source is
locked.
0-200
 Available when the input source is
locked.
0-200
 Available when the input source is
locked.
0-200
 Available when the input source is
locked.
0-200
 Available when the input source is
locked.
0-200
 Available when the input source is
locked.
0-200
 Available when the input source is
locked.
0-200
 Available when the input source is
locked.
0-200
 Available when the input source is
locked.
6
RM85001117EN00
Note
DK8500Z DLP Projector Remote Communication Manual
OSD Function
HSG/Cyan/Hue
Operation
command
hsg.c. hue
HSG/Magenta/Hue
hsg.m. hue
HSG/Yellow/Hue
Hsg.y. hue
HSG/White/Red Gain
hsg.wr.gain
HSG/White/Green Gain hsg.wg.gain
Settings/Return Values
?
=
+
?
=
+
?
=
+
?
=
+
?
=
+
?
=
+
-
HSG/White/Blue Gain
Hsg.wb.gain
HSG Reset
hsg.reset
Dynamic Black
dblack
?
=
Freeze
freeze
?
=
Alignment
OSD Function
Note
0-200
 Available when the input source is
locked.
0-200
 Available when the input source is
locked.
0-200
 Available when the input source is
locked.
0-200
 Available when the input source is
locked.
0-200
 Available when the input source is
locked.
0-200
 Available when the input source is
locked.
(execute)
0 = Off
1 = On
 Available when the input source is
locked.
 Not applicable when the projector is
at below condition:
Standby mode.
Edge Blend is On
3D mode
Dynamic Black is off
 Not applicable when the projector is
at standby mode
0 = Off
1 = On
Operation
command
zoom.in
Settings/Return Value
(execute)
 Not applicable when the projector is
at standby mode
Lens control
Zoom
zoom.in.2
(execute)
 Not applicable when the projector is
at standby mode.
Lens control
Zoom In
zoom.in.3
(execute)
 Not applicable when the projector is
at standby mode.
Lens control
Zoom Out
zoom.out
(execute)
 Not applicable when the projector is
at standby mode.
Lens control
Zoom Out
zoom.out.2
(execute)
 Not applicable when the projector is
at standby mode.
Lens control
Zoom Out
zoom.out.3
(execute)
 Not applicable when the projector is
at standby mode.
Lens control
Focus near
focus.near
(execute)
 Not applicable when the projector is
at standby mode
Lens control
Zoom
7
RM85001117EN00
Note
DK8500Z DLP Projector Remote Communication Manual
OSD Function
Operation
command
focus.near.2
Settings/Return Value
(execute)
 Not applicable when the projector is
at standby mode.
Lens control
Focus near
focus.near.3
(execute)
 Not applicable when the projector is
at standby mode.
Lens control
Focus far
focus.far
(execute)
 Not applicable when the projector is
at standby mode.
Lens control
Focus far
focus.far.2
(execute)
 Not applicable when the projector is
at standby mode.
Lens control
Focus far
focus.far.3
(execute)
 Not applicable when the projector is
at standby mode
Lens control
Lens up
lens.up
(execute)
 Not applicable when the projector is
at standby mode.
Lens control
Lens up
lens.up.2
(execute)
 Not applicable when the projector is
at standby mode.
Lens control
Lens up
lens.up.3
(execute)
 Not applicable when the projector is
at standby mode.
Lens control
Lens down
lens.down
(execute)
 Not applicable when the projector is
at standby mode.
Lens control
Lens down
lens.down.2
(execute)
 Not applicable when the projector is
at standby mode.
Lens control
Lens down
lens.down.3
(execute)
 Not applicable when the projector is
in standby mode.
Lens control
Len left
Lens control
Len left
lens.left
(execute)
lens.left.2
(execute)
 Not applicable when the projector is
at standby mode
 Not applicable when the projector is
at standby mode.
Lens control
Len left
lens.left.3
(execute)
 Not applicable when the projector is
at standby mode.
Lens control
Lens right
lens.right
(execute)
 Not applicable when the projector is
at standby mode.
Lens control
Lens right
lens.right.2
(execute)
 Not applicable when the projector is
at standby mode.
Lens control
Lens right
lens.right.3
(execute)
 Not applicable when the projector is
at standby mode.
Lens Memory /
Load Memory
lens.load
?
=
1-10 set of lens memory
(Load)
 Not applicable when the projector is
at standby mode
Lens Memory /
Save Memory
lens.save
?
=
1-10 set of lens memory
(Save)
 Not applicable when the projector is
at standby mode.
Lens Memory /
Clear Memory
lens.clear
?
=
1-10 set of lens memory
(Save)
 Not applicable when the projector is
at standby mode.
Center Lens
lens.center
(execute)
Lens Type
Lens.type
0 = non-UST
1 = UST lens
 Not applicable when the projector is
at standby mode or Lens Lock is
enabled.
 Not applicable when the projector is
at standby mode.
Lens Lock
Lens.lock
?
=
0 = Off
1 = On
 Not applicable when the projector is
at standby mode.
Digital Zoom /
Digital Zoom
digi.zoom
=
?
0 - 100
 Not applicable when the projector is
at standby mode.
Lens control
Focus near
8
RM85001117EN00
Note
DK8500Z DLP Projector Remote Communication Manual
OSD Function
Digital Zoom /
Digital Pan
Operation
command
digi.pan
Settings/Return Value
=
?
Note
-1280 - 1280
(depend on input timing;
use "op digi.pan ?" to
query current setting)
= -720 - 720
? (depend on input timing;
use "op digi.scan.?" to
query current setting
(execute)
 Not applicable when the projector is
at standby mode.
=
?
1 = Keystone
2 = Four Conner
3 = Rotation
4 = Pin/Barrel
5 = Arc
 Not available when projector is at
standby mode.
(execute)
 Not available when projector is at
standby mode.
Digital Zoom /
Digital Scan
digi.scan
Digital Zoom /
Reset
digi.zoom.rst
Active Warp
(Not on OSD)
active.warp
Reset Warp setting
(Not on OSD)
Warp.reset
Warp / Keystone H
h.keystone
=
?
Horizontal -470 ~ +470
 Available when active.warp is set to
1 (keystone) or 4 (Pincushion)
Warp / Keystone V
v.keystone
=
?
Vertical -400 ~ + 400
 Available when active.warp is set to
1 (keystone) or 4 (Pincushion)
(execute)
 Not available when projector is at
standby mode
-100 ~ +100
 Available when active.warp is set to
1 (keystone), 3 (Rotation) or 4
(Pincushion).
 Not available when projector is at
standby mode
Warp / Keystone reset Keystone.reset
=
?
 Not applicable when the projector is
at standby mode.
 Not applicable when the projector is
at standby mode.
Warp / Rotation
rotation
Warp / Rotation reset
rotation.reset
Warp / H Pin/Barrel
h.pin.barrel
=
?
-150 ~ + 300
 Available when active.warp is set to
(Pincushion).
Warp/ V Pin/Barrel
v.pin.barrel
=
?
-150 ~ + 300
 Available when active.warp is set to
4 (Pincushion).
Warp/ V Pin/Barrel
Reset
Pin.barrel.reset
(execute)
 Not available when projector is at
standby mode
Warp/ Top Left
Corner/Horizontal
4corner.ulx
=
?
-192 ~+192
 Available when active.warp is set to
2 (Four Corner).
Warp/ Top Left
Corner/Vertical
4corner.uly
=
?
-120 ~+120
 Available when active.warp is set to
2 (Four Corner).
Warp/ Top Right
Corner/ Horizontal
4corner.urx
=
?
-192 ~+192
 Available when active.warp is set to
2 (Four Corner).
Warp/ Top Right
Corner/ Vertical
4corner.ury
=
?
-120 ~+120
 Available when active.warp is set to
2 (Four Corner).
Warp/Bottom left
Corner/ Horizontal
4corner.llx
=
?
-192 ~+192
 Available when active.warp is set to
2 (Four Corner).
Warp/Bottom left
Corner/ Vertical
4corner.lly
=
?
-120 ~+120
 Available when active.warp is set to
2 (Four Corner).
Warp/Bottom Right
Corner/ Horizontal
4corner.lrx
=
?
-192 ~+192
 Available when active.warp is set to
2 (Four Corner).
Warp/Bottom Right
Corner/ Vertical
4corner.lry
=
?
-120 ~+120
 Available when active.warp is set to
2 (Four Corner).
(execute)
9
RM85001117EN00
DK8500Z DLP Projector Remote Communication Manual
OSD Function
Warp/ Corner
Reset
Operation
command
4corner.reset
Settings/Return Value
Note
(execute)
 Not available when projector is at
standby mode
Warp / Arc / Top
Arc.top
=
?
-150 ~+150
 Available when active.warp is set to
5 (Arc).
Warp / Arc / Bottom
arc.bottom
=
?
-150 ~+150
 Available when active.warp is set to
5 (Arc)
Warp / Arc / Left
arc.left
=
?
-150 ~+150
 Available when active.warp is set to
5 (Arc)
Warp / Arc / Right
arc.right
=
?
-150 ~+150
 Available when active.warp is set to
5 (Arc)
Warp / Arc /Reset
arc.reset
(execute)
 Not available when projector is at
standby mode
Blanking /
Top
blanking.top
=
?
0 ~ 360
 Not available when projector is at
standby mode.
Blanking /
Bottom
blanking.bottom
=
?
0 ~ 360
 Not available when projector is at
standby mode.
Blanking /
left
blanking.left
=
?
0 ~ 534
 Not available when projector is at
standby mode.
Blanking /
Right
blanking.right
=
?
0 ~ 534
 Not available when projector is at
standby mode.
Blanking /
Reset
blanking.reset
(execute)
 Not available when projector is at
standby mode.
Edge Blend
eb.stat
=
?
0 = Off
1 = On
 Not available when projector is at
standby mode.
Edge Blend /
Align Pattern
eb.adl
=
?
0 = Off
1 = On
 Available when Edge Blend is set to
On (eb.stat =1).
Edge Blend /
White Level
eb.top
=
?
0 100~500
 Available when Edge Blend is set to
On (eb.stat =1).
Edge Blend /
White Level
eb.bottom
=
?
0 100~500
 Available when Edge Blend is set to
On (eb.stat =1).
Edge Blend /
White Level
eb.left
=
?
0 100~800
 Available when Edge Blend is set to
On (eb.stat =1).
Edge Blend /
White Level
eb.right
=
?
0 100~500
 Available when Edge Blend is set to
On (eb.stat =1).
Edge Blend /
Black Level
eb.blu.top
=
?
0 ~ 32
 Available when Edge Blend is set to
On (eb.stat =1).
Edge Blend /
Black Level
eb.blu.bottom
=
?
0 ~ 32
 Available when Edge Blend is set to
On (eb.stat =1).
Edge Blend /
Black Level
eb.blu.left
=
?
0 ~ 32
 Available when Edge Blend is set to
On (eb.stat =1).
Edge Blend /
Black Level
eb.blu.right
=
?
0 ~ 32
 Available when Edge Blend is set to
On (eb.stat =1).
Edge Blend /
Black Level
eb.all
=
?
0 ~ 32
 Available when Edge Blend is set to
On (eb.stat =1).
Edge Blend /
Black Level
eb.red
=
?
0 ~ 32
 Available when Edge Blend is set to
On (eb.stat =1).
Edge Blend /
Black Level
eb.green
=
?
0 ~ 32
 Available when Edge Blend is set to
On (eb.stat =1).
10
RM85001117EN00
DK8500Z DLP Projector Remote Communication Manual
OSD Function
Edge Blend /
Black Level
Operation
command
eb.blue
Settings/Return Value
=
?
Note
0 ~ 32
 Available when Edge Blend is set to
On (eb.stat =1).
(execute)
 Available when Edge Blend is set to
On (eb.stat =1).
0 = 16:10
1 = 16:9
2 = 4:3
 Not available when the projector is
at standby mode.
Edge Blend /
Reset
eb.reset
Screen Format
screen.format
=
?
Settings/Return Values
Note
Language
Operation
command
lang
?
=
 Not available when the projector is
at standby mode.
Projection mode
orientation
=
?
0 = English
1 = French
2 = Spanish
3 = German
4 = Portuguese
5 = Chinese Simplified
6 = Chinese Traditional
7 = Japanese
8 = Korean
0 = Front Desktop
1 = Front Ceiling
2 = Rear Desktop
3 = Rear Ceiling
Altitude
altitude
?
=
0 = Reserved for other
applications
1 = On
2 = Auto
3 = Quiet
 Not available when the Network
Standby is set to ECO(lan.power=0)
Auto Power Off
auto.powoff
Auto Power On
auto.powon
Network/ Standby
Power
standby.power
?
=
?
=
=
?
0 = Off
1 = On
0 = Off
1 = On
0 = Saving
1 = ECO
2 = Normal
 Not available when the projector is
at standby mode.
 Not available when the projector is
at standby mode.
 Not applicable when the project is at
standby mode.
Network/DHCP
net.dhcp
?
=
0 = Off
1 = On
 Not applicable when the project is at
standby mode.
Network/IP Adress
net.ipaddr
?
=
<string>
 Not applicable when the project is at
standby mode.
Network/Subnet Mask net.subnet
?
=
<string>
 Not applicable when the project is at
standby mode.
Network/Gateway
net.gateway
?
=
<string>
 Not applicable when the project is at
standby mode.
Network/DNS
net.dns
?
=
<string>
 Not applicable when the project is at
standby mode.
Network/MAC address net.mac
?
=
<string>
 Not applicable when the project is at
standby mode.
CONTROL
OSD Function
11
RM85001117EN00
 Not available when the projector is
at standby mode.
DK8500Z DLP Projector Remote Communication Manual
OSD Function
Light Power
Operation
command
laser.mode
Settings/Return Values
Note
?
=

Customer
Power Level
laser.power
?
=
Constant Brightness
Enable / Disable
Laser.cbc.enable
?
=
0 = Eco Mode
1 = Normal Mode
2 =custom Power Mode
Not applicable when the project is
in standby mode

20-100
 Not applicable when the project is in
Adjust range: 20%-100%
standby mode and Light Power is
not set to Custom Power Level
(laser.mode=2).
0 = Off
 Not applicable when the project is in
1 = On
standby mode
Constant Brightness
laser.cbc.state
Check the status of the
function.
?
=
Background
no.signal
?
=
0 = Normal

1 = Laser power is driven
to the limit, Constant
Brightness can’t work.
1 = Black
 Not applicable when the project is in
2 = Blue
standby mode
Startup Logo
startup.logo
?
=
0 = Off
1 = On
 Not applicable when the project is at
standby mode
Remote Sensor
ir.enable
=
?
0 = Off (Disable)
1 = On (Enable)
 Not applicable when the project is in
standby mode
Trigger
trig.1
?
=
0 = Off
1 = Screen
2 = 5:4
3 = 4:3
4 = 16:10
5 = 16:9
6 = 1.88
7 = 2.35
8 = LetterBox
9 = Source
10 = Native
 Not applicable when the projector is
at standby mode.
Infrared Remote/
Remote Sensor
Ir.enable
=
?
0 = Off (Disable)
1 = On (Enable)
 Not applicable when the project is at
standby mode
Infrared Remote/ ID
Control Enable
Id.control.enable
=
?
0 = Off (Disable)
1 = On (Enable)
 Not applicable when the project is at
standby mode
Infrared Remote/
Control ID Number
Control.id
=
?
1-99
OSD Settings/ Menu
Position
osd.menupos
=
?
OSD Settings/ Menu
Transparency
osd.trans
=
?
0 = Top Left
1 = Top Right
2 = Bottom Left
3 = Bottom Right
4 = Center
0 = 0%
1 = 25%
2 = 50%
3 = 75%
 Not applicable when the project is at
standby mode and ID Control is
disabled(off)
 Not applicable when the project is at
standby mode
OSD Settings/ Time
Out
osd.timer
=
?
OSD Settings/
Message Box
osd.msgbox
=
?
0 = Always On
1 = 10 Seconds
2 = 30 Seconds
3 = 60 Seconds
0 = Off
1 = On
12
RM85001117EN00
 Not applicable when the project is at
standby mode
 Not applicable when the project is at
standby mode
 Not applicable when the project is at
standby mode
DK8500Z DLP Projector Remote Communication Manual
SERVICE
OSD Function
Settings/Return Values
Model
Operation
command
model
?
<String>
Serial Number
Software Version
Active Source
ser.no
sw.ver
act.source
?
?
?
<String>
<String>
Signal format
signal
?
H Refresh Rate
h.refresh
V Refresh Rate
Note

Applicable when the input source is
locked.
<string>

Applicable when the input source is
locked.
?
<number>
 Applicable when the input source is
locked.
v.refresh
?
<number>
Pixel Clock
pixel.clock
?
<number>
 Applicable when the input source is
locked
 Applicable when the input source is
locked.
Light Time
laser.hours
?
<number>
Factory Reset
fact.reset
Others
Function
(execute)
Power On
Operation
command
power.on
Settings/Return Values
Power Off
power.off
Projector Status
status
?
Blank
blank
Error Detection
Note
(execute)
(execute)
=
?
0 = Standby
1 = Warm Up
2 = Imaging
3 = Cooling
4 = Error
0= Disable
1= Enable
 Not applicable when the project is at
standby mode
errcode
?
<string>

System Temperature
- Ti
ti
?
<number>
 Not applicable when the project is in
standby mode
System Temperature
- Ti2
ti2
?
<number>
 Not applicable when the project is in
standby mode
System Temperature
- Tc
tc
?
<number>
 Not applicable when the project is in
standby mode
System Temperature
- Tb1
tb1
?
<number>
 Not applicable when the project is in
standby mode
System Temperature
- Tb2
tb2
?
<number>
 Not applicable when the project is in
standby mode
Note: The projector returns string "NA" when the input command does not apply to current projector status or setup.
13
RM85001117EN00
DK8500Z DLP Projector Remote Communication Manual
Simulated IR remote controller commands
This control command simulates the IR remote controller and its control keys. It uses the same syntax of operation
commands. It begins with characters "ky", followed by control commands and settings separated by a black space
[SP], and ending by carriage return pair "CR" and "ASCII hex 0D".Control command syntax:
ky[SP]<operation command>[CR]
Examples:
Power On
Power Off
ky power.on [CR]
ky power.off [CR]
List of simulated IR remote controller commands
Item
Function
1
Power On
Operation
command
power.on
2
Power Off
power.off
Power Off
3
Menu
menu
Display OSD menu
4
Exit
exit
Exit
5
Enter
enter
ENTER key
6
Up
up
Move cursor upward or change upward
7
Down
down
Move cursor downward or change downward
8
Left
left
Move cursor to the left or change to the left
9
Right
right
Move cursor to the right or change to the right
Description
Power On
14
RM85001117EN00
DK8500Z DLP Projector Remote Communication Manual
Control the Projector Through a Network
This projector supports the following methods in remotely controlling the projector through a network:
 Control projector through web browser.
 Control projector with RS-232 control or simulated IR commands via TCP/IP communication protocol.
Cable connection
You may connect the projector to a PC or an external integrated video and control signal transmission box through
LAN for controlling the projector.
Connect the projector to a PC
There are two ports for control via Ethernet. You can connect the PC to the HDBaseT/LAN or Ethernet port of the
projector for controlling the projector.
Connect with an external HDBaseT Transmitter
You may connect the projector to an external HDBaseT transmitter with an RJ-45 cable for concurrent video and
networking control signal transmission. Please connect the PC to the transmitter with one RJ-45 cable or RS-232
cable, then connect the transmission box to the HDBaseT/LAN terminal of the projector with one RJ-45 cable.
Please refer to below illustration.
15
RM85001117EN00
DK8500Z DLP Projector Remote Communication Manual
Set up the projector for networking
Before setting up the projector network settings, please make sure to configure the network settings and make
sure that the Standby Model is set to the corresponding setting.
Setup the Standby Mode
There are three options modes under Standby Mode, so please setup the Standby Mode according to the control
terminal you plan to connect with.
Normal: The Normal Mode ensures the higher power consumption (< 6W) for projector can be controlled via
RS-232, Ethernet, or HDBaseT/LAN terminal. In this mode, the projector can be controlled by the command
through HDBaseT/LAN port.
Eco: The Eco Mode ensures the power consumption is less 3W, and the projector can be controlled by the
command through RS-232 or Ethernet terminal only.
Saving: The Savings Mode ensures the lowest power consumption (<0.5W), and the projector can be
controlled by the command through RS-232 terminal or power button.
Configure the Network settings
When using network control, it’s required to set up the control PC and projector within the same network segment.
INPUT
PICTURE
ALIGNMENT
CONTROL
SERVICE
Network
DHCP
172.016.026.197
IP Address
255.255.254.000
Subnet Mask
255.255.255.000
Gateway
000.000.000.000
DNS
000.000.000.000
MAC Address
00:18:23:00:00:00
EXIT = Back
Off
↩/►
Scroll ▲▼
Item Adjust ◄►
DHCP: Enable or disable the DHCP service. When DHCP is set to ON, the DHCP server of the domain will assign
an IP address to the projector. The IP address will appear in the IP address window and you don't need to set the
IP address. Otherwise, the domain does not or cannot assign any IP address, and 0. 0. 0. 0 is shown on the IP
address window.
IP Address: Set DHCP “OFF” and specify an IP address manually. Use the ◄► button to select the number in the
address to change. Use the ▲▼ button to increase or decrease the number in the IP address.
Subnet Mask: Set the sub mask. The input method is the same as the setting for the IP address.
Gateway: Set the gateway. The input method is the same as the setting for the IP address.
DNS: Set the DNS. The input method is the same as the setting for the IP address.
MAC Address: Shows the projector’s MAC Address.
16
RM85001117EN00
DK8500Z DLP Projector Remote Communication Manual
Control the projector through a network
The projector can be controlled by the built-in webpage or by sending RS-232 commands via TCP/IP communication
protocol. You can select your preferred control per the application.
Control the projector through a web browser
Open the web browser of your control PC; type the IP address you set in the projector. The control page will be shown
as per the below image. The web control page is composed of seven tabs and three hot keys for projector control and
status.
Tab:
Projector Status
Projector Control
: Display current projector information and status
: This page provides the interface to control power, input and projection lens.
Crestron RoomView : Display Crestron web control page.
Network Setup
: Configure the network settings.
Alert Mail Setup
Error Log
OSD Function
: Settings for projector abnormality email alert messages. In case of any abnormality, the
projector sends email alert messages to preset users.
: Display error log of the projector
: This page displays the options on OSD menu. The structure and options are same as
most of the items on the projector’s OSD menu.
Hot Key:
Blank
: Blank the screen to stop the projection temporarily
Freeze
: Freeze the projected image
OSD
: Enable or disable OSD menu of the projector. Press this button to hide OSD menu, press
again to display menu.
17
RM85001117EN00
DK8500Z DLP Projector Remote Communication Manual
Projector Status:
This page displays the projector information and system status.
Model
Software Version
Power Status
Input
Laser status
Projection Mode
High Altitude
Intake Temperature
DMD Temperature
Laser Temperature
Diagnostic Status
: Projector model name
: The version of the software installed in the projector
: Current projector startup status
: Display the current input source.
: Display current light source status and the usage.
: Display current projection mode
: Display current High Altitude setting.
: Display detected temperature of intake air.
: Display detected temperature by the sensor near DMD chip.
: Display detected temperature by the sensor on laser module.
: Indicate self-diagnosis message by the projector.
LAN Information
MAC address
: Projector MAC address setup
18
RM85001117EN00
DK8500Z DLP Projector Remote Communication Manual
Projector Control
This page provides the control buttons for Power, Input Selection and Lens control.
Power
Input Selection
Lens Control
: Projector power on/off control.
: Select the input source by pressing the buttons.
: Select the button to adjust Zoom, Focus or Lens position, the symbol “<” on the
button represents the increment of each button operation. For example, the
button “<<<” is to adjust lens three steps after each press.
19
RM85001117EN00
DK8500Z DLP Projector Remote Communication Manual
Crestron RoomView
This page shows Crestron control page for projector control. The available options are listed below.
Power: Press this button to turn power on or off the projector.
Source List: Switch projector input sources. Press the ▲ or ▼ arrow key to scroll through the dropdown
list of available input sources
Image Adjust Options
Press the ◄ or ► arrow key to scroll through available adjustment options.
Freeze: Freeze current projection screen. The projection screen prompts the "Still open" message after the
freeze function enabled. Press the Freeze button again to unfreeze the screen.
Contrast: Click this button and the adjustment window displays. Click the ◄► arrow keys to adjust contrast.
Brightness: Click this button and the adjustment window displays. Click the ◄► arrow keys to adjust brightness.
Sharpness: Click this button and the adjustment window displays. Click the ◄► arrow key to adjust sharpness.
Zoom: Zoom the projection image. Click the "+" key to zoom in and "-" to zoom out. You may click the four
arrow keys in the window to move the zoomed projection image.
20
RM85001117EN00
DK8500Z DLP Projector Remote Communication Manual
Control key window
This window simulates the keys on the remote controller and control panel.
Enter: Confirm and select function options
Menu: Press to display OSD menu. Press again to exit it.
Auto: Run the auto image adjustment function.
Blank: Pause the image projection, i.e. the projection image is masked. Press again to resume the projection.
Source: The signal source menu displays. Press to display signal source in the projection screen.
Tools: Check Crestron equipment for its setup
Info: Display current projector status and Crestron setup.
Network Setup
This page allows you to configure the projector’s network settings.
DHCP
:
IP Address
Subnet
Mask
Gateway
DNS Server
Save Setting
:
:
:
:
The DHCP server domain will assign an IP address to the projector automatically if
DHCP is set to On, otherwise network configuration need to be set manually.
Input the IP address of the projector.
Configure the subnet mask.
Configure the gateway
Set the address of DNS server
Click the button to confirm the change if any change is made.
Note:
 Current connection will be interrupted after you change the network settings. Please make
necessary change in your personal computer and web browser, and then connect again.
21
RM85001117EN00
DK8500Z DLP Projector Remote Communication Manual
Alert Mail Setup
This projector can send email alert messages to present users outlining the projector’s abnormalities. Set
up and install the projector before enabling this function:
SMTP Server
Port
User Name
Password
E-mail Alert
From
To
CC
Projector Name
Location
Apply
Send Test Mail
: Set up SMTP server name.
: Set up port name.
: Input user name for the projector to send the reminding message through a SMTP
server
: Input password.
: Enable or Disable reminding message
: Set up sender’s email address
: Set up receiver’s email address
: Set up email address of the email send a copy of a business letter or an e-mail.
: Set up projector name or ID.
: Set up projector installation location.
: Press this button to confirm changes you have made.
: Send test email. Press this button to validate email settings after setup is completed.
Error Log
This page displays the error log of the projector. This information is helpful to service staff to diagnose the projector.
Please capture this page and send It the service staff if you have any questions during the usage of this projector.
22
RM85001117EN00
DK8500Z DLP Projector Remote Communication Manual
OSD Function
This page lists most of the OSD functions into sub tabs per the OSD structure and options of the projector.
Control projector with TCP/IP communication protocol
This projector supports TCP/IP communication protocol which enables you to send RS-232 operation commands or
simulated IR commands to control projectors. The projectors are connected with RJ45 cable via terminal connection
application software, e.g. Tera Term. Please set up IP address and port number with the terminal connection
application software before controlling your projector with TCP/IP communication protocol:
IP Address: IP address of projector
Port: Please set transmission port number to 7000
See the section on serial interface RS-232 control commands for details on RS-232 operation commands or simulated
IR commands.
23
RM85001117EN00
DK8500Z DLP Projector Remote Communication Manual
About Vivitek Support
If you cannot find solutions from this user guideline, please contact us using the contact information below:
Europe, Middle East and Africa
Vivitek Service & Support
Zandsteen 15
2132 MZ Hoofddorp
The Netherlands
Tel: +31-(0)-20-721-9318
Email: support@vivitek.eu
URL: http://www.vivitek.eu/support/tech-support
North America
Vivitek Service Center
15700 Don Julian Road, Suite B
City of Industry, CA. 91745
U.S.A
Tel: 855-885-2378 (Toll-Free)
Email: T.services1@vivitekcorp.com
URL: www.vivitekusa.com
Asia and Taiwan
Vivitek Service Center
5F, No.186, Ruey Kuang Road, Neihu District
Taipei, Taiwan 11491
Tel: 886-2-8797-2088, ext. 6899 (Direct)
Tel: 0800-042-100 (Toll-Free)
Email: kenny.chang@vivitek.com.tw
URL: www.vivitek.com.tw
中国/China
Vivitek客服中心
上海市闵行区申长路618号绿谷广场A座7楼
邮政编码: 201106
400客服热线: 400 888 3526
公司电话: 021-58360088
客服邮箱: service@vivitek.com.cn
官方网站: www.vivitek.com.cn
24
RM85001117EN00
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement