Vivitek D5010-WNL Projector User's Manual

Vivitek D5010-WNL Projector User's Manual
Copyright
This publication, including all photographs, illustrations and software, is protected under international
copyright laws, with all rights reserved. Neither this manual, nor any of the material contained herein, may
be reproduced without written consent of the author.
© Copyright 2013
Disclaimer
The information in this document is subject to change without notice. The manufacturer makes no
representations or warranties with respect to the contents hereof and specifically disclaims any implied
warranties of merchantability or fitness for any particular purpose. The manufacturer reserves the right to
revise this publication and to make changes from time to time in the content hereof without obligation of
the manufacturer to notify any person of such revision or changes.
Trademark Recognition
Kensington is a U.S. registered trademark of ACCO Brand Corporation with issued registrations
and pending applications in other countries throughout the world.
HDMI, the HDMI Logo, and High-Definition Multimedia Interface are trademarks or
registered trademarks of HDMI Licensing LLC in the United States and other countries.
All other product names used in this manual are the properties of their respective owners and are
acknowledged.
—i—
DLP Projector—User’s Manual
Important Safety Information
Important:
It is strongly recommended that you read this section carefully before using the projector. These
safety and usage instructions will ensure that you enjoy many years of safe use of the projector.
Keep this manual for future reference.
Symbols Used
Warning symbols are used on the unit and in this manual to alert you of hazardous situations.
The following styles are used in this manual to alert you to important information.
Note:
Provides additional information on the topic at hand.
Important:
Provides additional information that should not be overlooked.
Caution:
Alerts you to situations that may damage the unit.
Warning:
Alerts you to situations that may damage the unit, create a hazardous environment, or cause
personal injury.
Throughout this manual, component parts and items in the OSD menus are denoted in bold font as in this
example:
“Push the Menu button on the remote control to open the Main menu.”
General Safety Information

Do not open the unit case. Aside from the projection lamp, there are no user-serviceable parts in
the unit. For servicing, contact qualified service personnel.

Follow all warnings and cautions in this manual and on the unit case.

The projection lamp is extremely bright by design. To avoid damage to eyes, do not look into the
lens when the lamp is on.

Do not place the unit on an unstable surface, cart, or stand.

Avoid using the system near water, in direct sunlight, or near a heating device.

Do not place heavy objects such as books or bags on the unit.
— ii —
PPrreeffaaccee
Projector Installation Notice

Place the projector in a horizontal position
The tilt angle of the projector please see Tilt Up/Down caution on page 52.

Allow at least 50 cm clearance around the exhaust vent.

Ensure that the intake vents do not recycle hot air from the exhaust vent.

When operating the projector in an enclosed space, ensure that the surrounding air temperature
within the enclosure does not exceed operation temperature while the projector is running, and the
air intake and exhaust vents are unobstructed.

All enclosures should pass a certified thermal evaluation to ensure that the projector does not
recycle exhaust air, as this may cause the device to shutdown even if the enclosure temperature is
with the acceptable operation temperature range.
– iii –
DLP Projector—User’s Manual
Verify Installation Location

To supply power, the 3-blade (with earthing lead) socket should be used to ensure proper
grounding and equalized ground potential for all of the equipment in the Projector System.

The power code provided with the Projector should be used. In case of any missing item, other
qualified 3-blade (with earthing lead) power cord can be used as substitution; however, do not use
2-blade power cord.

Verify if the voltage is stable, grounded properly and there is no electricity leakage.

Measure total power consumption which should not higher the safety capacity and avoid safety
issue and short circuit.

Turn on Altitude Mode when located in high altitude areas

When installation the bracket, make sure the weight limit is not exceed and firmly secured.

Avoid installing near air conditioner duct or subwoofer.

Avoid installing at high temperature, insufficient cooling and heavy dust locations.

Keep your product away from fluorescent lamps (>1 meter) to avoid malfunction
caused by IR interference

The VGA IN connector should be connected to the VGA IN port. Note that it should be inserted
tightly, with the screws on both sides securely fastened to ensure proper connection of the signal
wire for achieving optimal display effect.

The AUDIO IN connector should be connected to the AUDIO IN port and CANNOT be connected
to AUDIO OUT or other ports like BNC, RCA; otherwise, it will lead to mute output and even
DAMAGE the port.

Install the projector above 200cm to avoid damage.

The power cord and signal cable should be connected before power on the projector. During the
projector starting and operating process, DO NOT insert or remove the signal cable or the power
cord to avoid damaging the projector.
Cooling notes
Air outlet
 Make sure the air outlet is 50cm clear of any obstruction to ensure proper cooling.

Air outlet location should not be in front of the lens of other projector to avoid causing illusions.

Keep the outlet at least 100cm away from the inlets of other projectors

The projector generates a massive amount of heat during use. The internal fan dissipates the heat
of the projector when shutting down, and such process may continue for a certain period. After the
project enters STANDBY MODE status, press the AC power button to turn off the projector and
remove the power cord. DO NOT remove the power cord during the shutdown process, as it may
cause damage to the projector. In the meantime, the delayed heat radiating will also affect the
service life of the projector. The shutdown process may vary depending on the model used.
Whatever the case may be, be sure to disconnect the power cord till after the projector enters the
STANDBY status.
Air inlet
 Make sure there is no object blocking air input within 30 cm.

Keep the inlet away from other heat sources

Avoided heavy dust area
— iv —
PPrreeffaaccee
Power Safety

Only use the supplied power cord.

Do not place anything on the power cord. Place the power cord where it will not be in the way of
foot traffic.

Remove the batteries from the remote control when storing or not in use for a prolonged period.
Replacing the Lamp
Replacing the lamp can be hazardous if done incorrectly. See Replacing the Projection Lamp on page 54
for clear and safe instructions for this procedure. Before replacing the lamp:

Unplug the power cord.

Allow the lamp to cool for about one hour.
Caution:
In rare cases the lamp bulb may burn out during normal operation and cause glass dust or shards
to be discharged outward from the rear exhaust vent.
Do not inhale or do not touch glass dust or shards. Doing so could result in injury.
Always keep your face away from the exhaust vent so that you do not suffer from the gas and
broken shards of the lamp.
Cleaning the Projector

Unplug the power cord before cleaning. See Cleaning the Projector on page 60.

Allow the lamp to cool for about one hour.
Regulatory Warnings
Before installing and using the projector, read the regulatory notices in the Regulatory Compliance on
page 80.
Important Recycle Instructions:
Lamp(s) inside this product contain mercury. This product may contain other electronic waste that
can be hazardous if not disposed of properly. Recycle or dispose in accordance with local, state, or federal
Laws. For more information, contact the Electronic Industries Alliance at WWW.EIAE.ORG. For lamp
specific disposal information check WWW.LAMPRECYCLE.ORG.
Symbol Explanations
DISPOSAL: Do not use household or municipal waste collection services for
disposal of electrical and electronic equipment. EU countries require the use
of separate recycling collection services.
–v–
DLP Projector—User’s Manual
Main Features

Lightweight unit, easy to pack away and transport.

Compatible with all major video standards including NTSC, PAL, and SECAM.

A high brightness rating allows for presentations in daylight or in lit rooms.

Supports resolutions up to WUXGA at 16.7 million colors to deliver crisp, clear images.

Flexible setup allows for front, rear projections.

Line-of-vision projections remain square, with advanced keystone correction for angled
projections.

Input source automatically detected.
About this Manual
This manual is intended for end users and describes how to install and operate the DLP projector.
Wherever possible, relevant information—such as an illustration and its description—has been kept on
one page. This printer-friendly format is both for your convenience and to help save paper, thereby
protecting the environment. It is suggested that you only print sections that are relevant to your needs.
— vi —
PPrreeffaaccee
Table of Contents
GETTING STARTED ........................................................................................................................................................... 1
PACKING CHECKLIST ........................................................................................................................................................... 1
VIEWS OF PROJECTOR PARTS ............................................................................................................................................... 2
Front-right View ............................................................................................................................................................ 2
Top view—On-screen Display (OSD) buttons and LEDs ....................................................................................... 3
Rear view ....................................................................................................................................................................... 4
Bottom view ................................................................................................................................................................... 6
REMOTE CONTROL PARTS ................................................................................................................................................... 7
REMOTE CONTROL OPERATING RANGE ............................................................................................................................... 9
PROJECTOR AND REMOTE CONTROL BUTTONS .................................................................................................................... 9
SETUP AND OPERATION............................................................................................................................................... 10
INSERTING THE REMOTE CONTROL BATTERIES ................................................................................................................. 10
INSTALLING OR REMOVING THE OPTIONAL LENS .............................................................................................................. 11
Removing the Existing Lens From the Projector ................................................................................................... 11
Installing the New Lens ............................................................................................................................................. 12
STARTING AND SHUTTING DOWN THE PROJECTOR ............................................................................................................. 13
SETTING AN ACCESS PASSWORD (SECURITY LOCK) .......................................................................................................... 15
ADJUSTING THE PROJECTOR LEVEL ................................................................................................................................... 17
ADJUSTING PROJECTED IMAGE POSITION USING SHIFT ..................................................................................................... 18
Adjusting the vertical image position ....................................................................................................................... 18
Adjusting the horizontal image position .................................................................................................................. 20
Shift Range Diagram ................................................................................................................................................. 20
ADJUSTING THE ZOOM, FOCUS AND KEYSTONE ................................................................................................................ 22
ADJUSTING THE VOLUME .................................................................................................................................................. 23
ON-SCREEN DISPLAY (OSD) MENU SETTINGS ...................................................................................................... 24
OSD MENU CONTROLS ..................................................................................................................................................... 24
Navigating the OSD ................................................................................................................................................... 24
SETTING THE OSD LANGUAGE .......................................................................................................................................... 25
OSD MENU OVERVIEW ..................................................................................................................................................... 26
IMAGE MENU ..................................................................................................................................................................... 27
Computer Menu .......................................................................................................................................................... 28
Advanced Feature ...................................................................................................................................................... 29
Color Manager ............................................................................................................................................................ 30
SETTINGS 1 MENU ............................................................................................................................................................. 31
Audio ............................................................................................................................................................................ 32
Advanced 1 Feature................................................................................................................................................... 33
Advanced 2 Feature................................................................................................................................................... 35
SETTINGS 2 MENU ............................................................................................................................................................. 36
Status ........................................................................................................................................................................... 37
Advanced 1 Feature................................................................................................................................................... 38
Advanced 2 Feature................................................................................................................................................... 50
MAINTENANCE AND SECURITY .................................................................................................................................. 52
TILT UP/DOWN CAUTION ................................................................................................................................................... 52
The model with Standard lamp module .................................................................................................................. 52
The model with Tilt lamp module ............................................................................................................................. 52
REPLACING THE PROJECTION LAMP................................................................................................................................... 54
Resetting the Lamp .................................................................................................................................................... 57
CLEANING THE FILTER (FILTER: OPTIONAL PARTS) ............................................................................................................ 58
REPLACING THE FILTER ..................................................................................................................................................... 59
CLEANING THE PROJECTOR................................................................................................................................................ 60
Cleaning the Lens ...................................................................................................................................................... 60
Cleaning the Case ...................................................................................................................................................... 60
USING THE PHYSICAL LOCK .............................................................................................................................................. 61
Using the Kensington® Lock ..................................................................................................................................... 61
Using the Security Chain Lock ................................................................................................................................. 61
– vii –
DLP Projector—User’s Manual
TROUBLESHOOTING ...................................................................................................................................................... 62
COMMON PROBLEMS AND SOLUTIONS ............................................................................................................................... 62
TIPS FOR TROUBLESHOOTING ............................................................................................................................................ 62
LED ERROR MESSAGES ..................................................................................................................................................... 63
IMAGE PROBLEMS .............................................................................................................................................................. 63
LAMP PROBLEMS ............................................................................................................................................................... 64
REMOTE CONTROL PROBLEMS .......................................................................................................................................... 64
AUDIO PROBLEMS ............................................................................................................................................................. 65
HAVING THE PROJECTOR SERVICED .................................................................................................................................. 65
HDMI Q & A .................................................................................................................................................................... 66
SPECIFICATIONS ............................................................................................................................................................. 67
SPECIFICATIONS................................................................................................................................................................. 67
SPECIFICATIONS................................................................................................................................................................. 68
PROJECTION DISTANCE VS. PROJECTION SIZE (WUXGA) ................................................................................................. 69
Projection Distance and Size Table......................................................................................................................... 69
PROJECTION DISTANCE VS. PROJECTION SIZE (WXGA) .................................................................................................... 71
Projection Distance and Size Table......................................................................................................................... 71
PROJECTION DISTANCE VS. PROJECTION SIZE (XGA)........................................................................................................ 73
Projection Distance and Size Table......................................................................................................................... 73
PROJECTION DISTANCE VS. PROJECTION SIZE (1080P) ...................................................................................................... 75
Projection Distance and Size Table......................................................................................................................... 75
TIMING MODE TABLE ........................................................................................................................................................ 77
PROJECTOR DIMENSIONS ................................................................................................................................................... 79
REGULATORY COMPLIANCE ....................................................................................................................................... 80
FCC WARNING .................................................................................................................................................................. 80
CANADA ............................................................................................................................................................................ 80
SAFETY CERTIFICATIONS ................................................................................................................................................... 80
APPENDIX I ........................................................................................................................................................................ 81
RS-232C PROTOCOL.......................................................................................................................................................... 81
— viii —
DLP Projector – User’s Manual
GETTING STARTED
Packing Checklist
Carefully unpack the projector and check that the following items are included:
PROJECTOR WITH LENS CAP
REMOTE CONTROL
(WITH TWO AA BATTERIES)
CD-ROM
(THIS USER’S MANUAL)
POWER CORD
VGA CABLE (1.8M)
WARRANTY CARD
QUICK START CARD
TILT LAMP MODULE
(OPTIONAL)
DUST FILTER
(OPTIONAL)
Contact your dealer immediately if any items are missing, appear damaged, or if the unit does not
work. It is recommend that you keep the original packing material should you ever need to return
the equipment for warranty service.
Caution:
Avoid using the projector in dusty environments.
—1—
DLP Projector—User’s Manual
Views of Projector Parts
Front-right View
5 6
12 3 4
ITEM
LABEL
78
9 10
DESCRIPTION
11
SEE PAGE:
1.
Screw
For ensure the lens position
2.
Vertical lens shift
Adjusts the image position vertically
18
3.
Lens release button
Press the release button before removing the
lens
11
4.
Horizontal lens shift
Adjusts the image position horizontally
20
5.
IR receiver
Receives IR signal from remote control
7
6.
Lens
Projection Lens
7.
Focus ring
Focuses the projected image
8.
Zoom ring
Enlarges the projected image
9.
Height adjuster
Adjusts level of projector
10.
Function keys
See Top view—On-screen Display (OSD)
buttons and LEDs.
11.
Lamp cover
Removes cover to replace lamp module
22
17
3
52
Important:
Ventilation openings on the projector allow for good air circulation, which keeps the projector
lamp cool. Do not obstruct any of the ventilation openings.
Note:
Suggest to loosen the screw before lens shift adjustment and tighten up after finished
adjustment.
—2—
D
DLLPP PPrroojjeeccttoorr—
—U
Usseerr’’ss M
Maannuuaall
Top view—On-screen Display (OSD) buttons and LEDs
ITEM
1.
LABEL
MENU
DESCRIPTION
3.
ENTER
Enter or confirm highlighted OSD menu item
4.
BLANK
Displays a blank screen and mutes audio
Navigates and changes settings in the OSD
Quick Menu – For Volume -
5.
6.
AUTO
Navigates and changes settings in the OSD
Quick Menu – For Volume +
8.
Navigates and changes settings in the OSD
Quick Menu – For Keystone
SOURCE
24
24
Optimizes image size, position, and resolution
7.
9.
PAGE:
Opens and exits OSD menus
Navigates and changes settings in the OSD
Quick Menu – For Keystone
2.
SEE
Enter the Source menu
–3–
24
DLP Projector—User’s Manual
Rear view
1 23 4
5
678
12 14 16
10 11 13 15
9
17
18
19
31
ITEM
30
29 28
LABEL
27 26
25
24
22 20
23 21
DESCRIPTION
SEE PAGE:
1.
VGA1
Connect a RGB cable from a computer or a video enabled device.
2.
AUDIO IN 1
Connect the AUDIO cable from an input device.
3.
VGA2
Connect a RGB cable from a computer or a video enabled device.
4.
AUDIO IN 2
Connect the AUDIO cable from an input device.
Note: Share with DVI & BNC audio input.
5.
POWER
Turns the projector on or off (main power switch must
be turned on first). Press to place the projector in
standby mode.
6.
PWR LED
Red
Standby, Over Temperature
Blue
Lamp Lit , System stable
Flashing
Power on, Cooling, Error code (See as
LED indicator table)
Red
Over temperature
Red
Lamp Lit , System stable, Lamp Fail
Flashing
Error code (See as LED indicator table)
7.
TEMP LED
8.
READY LED
9.
HDMI
Connect the HDMI cable from a HDMI device.
10.
DVI-D
Connect the DVI cable from a computer.
11.
3D SYNC OUT
(5V)
Connect 3D IR glasses receiver unit.
12.
DISPLAYPORT
Connect a DISPLAYPORT cable to a DISPLAYPORT source.
13.
USB CHARGE
(1.5A)
For USB charge.
14.
RJ-45
Connect a LAN cable from Ethernet.
—4—
13
63
D
DLLPP PPrroojjeeccttoorr—
—U
Usseerr’’ss M
Maannuuaall
ITEM
LABEL
DESCRIPTION
SEE PAGE:
15.
VGA OUT
Connect the RGB cable to a display.
(Pass through by VGA1 only)
16.
AUDIO OUT
Connect an AUDIO cable for audio loop through.
17.
BNC
Connect a BNC cable from a computer.
18.
IR receiver
Receive IR signal from remote control.
19.
SERVICE
For service use.
20.
RS-232
Connects RS-232 serial port cable for remote control.
21.
12V
When connected to the screen through a commercially available cable,
the screen deploys automatically on start up of the projector. The screen
retracts when the projector is powered off (see notes below).
22.
WIRED REMOTE
Wire remote control connector (connect with wire remote connector of the
Remote Control set).
23.
AUDIO IN 3 L/R
RCA (YPbPr)
Connect the audio cables from a audio device.
24.
AUDIO IN 4 L/R
RCA (Video/ SVideo)
Connect the audio cables from a audio device.
25.
VIDEO
Connect the composite cable from a video device.
26.
S-VIDEO
Connect the S-video cable from a video device.
27.
YPbPr
Connect a component video enabled device.
28.
AC IN
Connects the power cable.
29.
Power switch
Turns on/off the projector.
30.
Security chain
lock
Helps protect the projector from unauthorized use.
Kensington Lock
Secures to permanent object with a Kensington® Lock
system.
31.
7
13
61
Note:
 To use this feature, you must plug in the connector before turn on/off the projector.
 Screen controllers are supplied and supported by screen manufacturers.
 Do not use this jack for anything other than intended use.
Note:
If your video equipment has both S-VIDEO and RCA jacks (composite video) connect to the
S-VIDEO connector. S-VIDEO provides a better quality signal.
Warning:
As a safety precaution, disconnect all power to the projector and connecting devices before
making connections.
–5–
DLP Projector—User’s Manual
Bottom view
ITEM
LABEL
DESCRIPTION
SEE PAGE:
1.
Tilt adjustor
Rotate adjuster lever to adjust angle position.
2.
Ceiling support holes
Contact your dealer for information on mounting the projector on a
ceiling
17
Note:
When installing, ensure that you use only UL Listed ceiling mounts.
For ceiling installations, use approved mounting hardware and M4 screws with a maximum
screw depth of 6 mm (0.23 inch).
The construction of the ceiling mount must be of a suitable shape and strength. The ceiling
mount load capacity must exceed the weight of the installed equipment, and as an additional
precaution be capable of withstanding three times the weight of the equipment (not less than
5.15 kg) over a period of 60 seconds.
—6—
D
DLLPP PPrroojjeeccttoorr—
—U
Usseerr’’ss M
Maannuuaall
Remote Control Parts
Important:
1. Avoid using the projector with bright fluorescent lighting turned on. Certain high-frequency
fluorescent lights can disrupt remote control operation.
2. Be sure nothing obstructs the path between the remote control and the projector. If the path
between the remote control and the projector is obstructed, you can bounce the signal off
certain reflective surfaces such as projector screens.
3. The buttons and keys on the projector have the same functions as the corresponding buttons
on the remote control. This user’s manual describes the functions based on the remote control.
–7–
DLP Projector—User’s Manual
ITEM
1.
2.
3.
4.
LABEL
DESCRIPTION
Power OFF
Turns the projector off
DVI
Displays the DVI source selection
VGA
Displays the VGA source selection
DP
Displays the DisplayPort source selection
Up cursor /
Keystone+
Navigates and changes settings in the OSD
Quick Menu – For Keystone
ENTER
Enters and confirms settings in the OSD
Right cursor
Navigates and changes settings in the OSD
Down cursor /
Keystone-
Navigates and changes settings in the OSD
Quick Menu – For Keystone
9.
10.
11.
12.
13.
3D
Activate 3D video (not available in D5180HD series)
PICTURE MODE
Changes the Display Mode setting
SOURCE
Alternate input source
CONTRAST
Displays the contrast settings bar
BRIGHT
Displays the brightness setting bar
14.
SHARP
Displays the sharpness setting bar
15.
COLOR
Displays the color setting bar
16.
FREEZE
Freezes/unfreezes the on-screen picture
17.
VOL +
Adjusts volume
18.
AUTO
Auto adjustment for frequency, phase, and position
19.
VOL -
Adjusts volume
20.
21.
22.
BLANK
Makes the screen blank
TINT
Displays the tint setting bar
MUTE
Mutes the built-in speaker
23.
STATUS
Opens the OSD Status menu (the menu only opens when an input
device is detected)
24.
ASPECT RATIO
Displays the ASPECT RATIO selections
25.
MENU
Opens or closed the OSD
24
26.
Left cursor
Navigates and changes settings in the OSD
24
27.
28.
29.
30.
31.
32.
COMP
Displays the Component source selection
VIDEO
Displays the VIDEO source selection
HDMI 1
Displays the HDMI 1 source selection
Power ON
Turns the projector on
Status LED
Lights when the remote control is used
IR transmitter
Transmits signals to projector
Wired remote
connector
Wired remote function used
5.
6.
7.
8.
33.
—8—
SEE PAGE:
13
24
24
24
13
D
DLLPP PPrroojjeeccttoorr—
—U
Usseerr’’ss M
Maannuuaall
Remote Control Operating Range
The remote control uses infrared transmission to control the projector. It is not necessary to point
the remote directly at the projector. Provided you are not holding the remote perpendicular to the
sides or the rear of the projector, the remote will function well within a radius of about 7 meters (23
feet) and 15 degrees above or below the projector level. If the projector does not respond to the
remote control, move a little closer.
Projector and Remote Control Buttons
The projector can be operated using the remote control or the buttons on the top of the projector.
All operations can be carried out with the remote control; however, the buttons on the projector
are limited in use.
–9–
DLP Projector—User’s Manual
SETUP AND OPERATION
Inserting the Remote Control Batteries
1.
Remove the battery compartment
cover by sliding the cover in the
direction of the arrow.
2.
Insert the battery with the positive
side facing up.
3.
Replace the cover.
Caution:
1. Only use AA batteries (Alkaline batteries are recommended).
2. Dispose of used batteries according to local ordinance regulations.
3. Remove the batteries when not using the projector for prolonged periods.
— 10 —
D
DLLPP PPrroojjeeccttoorr—
—U
Usseerr’’ss M
Maannuuaall
Installing or Removing the Optional Lens
Caution:
 Do not shake or place excessive pressure on the projector or the lens components as the
projector and lens components contain precision parts.
 Before removing or installing the lens, be sure to turn off the projector, wait until the cooling
fans stop, and turn off the main power switch.
 Do not touch the lens surface when removing or installing the lens.
 Keep fingerprints, dust or oil off the lens surface.
 Do not scratch the lens surface.
 Work on a level surface with a soft cloth under it to avoid scratching.
 If you remove and store the lens, attach the lens cap to the projector to keep off dust and dirt.
Removing the Existing Lens From the Projector
1.
Pull and release the top cover to
open as shown.
2.
Push the LENSE RELEASE button
to the unlock position.
3.
Grasp the lens.
4.
Rotate the lens counterclockwise.
The existing lens will be
disengaged.
5.
Pull out the existing lens slowly.
– 11 –
DLP Projector—User’s Manual
Installing the New Lens
1.
Align the notches and correctly
position the electrical contact pad as
shown in the picture.
Electrical contact pins
Note:
Pin of Electrical contact pins should
be in the direction as shown in the
picture.
2.
Rotate the lens clockwise until you
feel it click into place.
— 12 —
D
DLLPP PPrroojjeeccttoorr—
—U
Usseerr’’ss M
Maannuuaall
Starting and Shutting down the Projector
1.
Remove the lens cap.
2.
Securely connect the power cord
and signal cable. When connected,
the power led will turn red.
3.
Turn on the lamp by pressing
“
” button on the rear of the
projector or “
” on the remote
control.
The PWR LED will now flash red.
The startup screen will display in
approximately 30 seconds. The first
time you use the projector, you can
select your preferred language from
quick menu after the startup screen
display.
– 13 –
DLP Projector—User’s Manual
4.
5.
If more than one input device is
connected, press the SOURCE
button and use ▲▼ to scroll among
devices.

DVI: Digital Visual Interface

HDMI: High-Definition Multimedia Interface
compatible

DisplayPort: Digital display interface

VGA 1 / 2: Analog RGB 1 / 2

BNC: Analog RGB (BNC connector)

Component Video: DVD input YCbCr / YPbPr , or
HDTV input YPbPr

S-Video: Super video (Y/C separated)

Composite Video: Traditional composite video
When the “Power Off? /Press
Power again” message appears,
press the POWER button. The
projector turns off.
Caution:
1. Be sure to remove the lens cap before starting projector.
2. Do not unplug the power cord until the READY LED stops flashing–indicating the projector
has cooled down.
— 14 —
D
DLLPP PPrroojjeeccttoorr—
—U
Usseerr’’ss M
Maannuuaall
Setting an Access Password (Security Lock)
You can use the four (arrow) buttons to set a password and prevent unauthorized use of the
projector. When enabled, the password must be entered after you power on the projector. (See
Navigating the OSD on page 24 and Setting the OSD Language on page 25 for help on using
OSD menus.)
Important:
Keep the password in a safe place. Without the password, you will not be able to use the
projector. If you lose the password, contact your reseller for information on clearing the
password.
1.
Press the MENU button to open the
OSD menu.
2.
Press the cursor ◄► button to move to
the Settings 1 menu, press the cursor
▲▼ button to select Advanced 1.
3.
Press
(Enter) / ► to enter the
Advanced 1 sub menu. Press the
cursor ▲▼ button to select Security
Lock.
4.
Press the cursor ◄► button to enter
and enable or disable security lock
function.
A password dialog box automatically
appears.
– 15 –
DLP Projector—User’s Manual
5.
You can use the cursor buttons
▲▼◄►
either on keypad or IR remote control
for password entry. You can use any
combination including the same arrow
five times, but not less than five.
Press the cursor buttons in any order to
set the password. Push the MENU
button to exit the dialog box.
6.
The password confirm menu appears
when user presses the power-on key in
case the Security Lock is enabled.
Enter the password in the order you set
it at step 5. In case you forget the
password, please contact the service
center.
The service center will validate the
owner and help reset the password.
— 16 —
D
DLLPP PPrroojjeeccttoorr—
—U
Usseerr’’ss M
Maannuuaall
Adjusting the Projector Level
Take note of the following when setting up the projector:

The projector table or stand should be level and sturdy.

Position the projector so that it is perpendicular to the screen.

Remove the Back Foot Holder on the rear adjuster foot before adjusting the projection
angle.

Ensure the cables are in a safe location. You could trip over them.
1.
To raise the level of the projector,
twist the adjusters counter
clockwise.
2.
To lower the level of the projector,
lift the projector and twist the
adjusters clockwise.
– 17 –
DLP Projector—User’s Manual
Adjusting Projected Image Position Using Shift
Note:
Suggest to loosen the screw before lens
shift adjustment and tighten up after
finished adjustment.
The Shift feature provides a lens shift function that can be used to adjust the position of the
projected image either horizontally or vertically within the range detailed below.
Shift is a unique system that provides lens shift while maintaining a much higher ANSI contrast
ratio than traditional lens shift systems.
Adjusting the vertical image position
The vertical image height can be adjusted between 55% and -15% ( WUXGA, WXGA),
50% and -10% (XGA), 60% and -20% ( 1080P) of offset position. Note that the maximum vertical
image height adjustment can be limited by the horizontal image position. For example it is not
possible to achieve the maximum vertical image position height detailed above if the horizontal
image position is at maximum. Please consult the Shift Range diagram below for further
clarification.
WUXGA and WXGA
Screen
Screen Height
(H)
-15%
15%xH
100%
0%
55%xH
Hx5%
+55%
Distance
(L)
WUXGA / WXGA
— 18 —
D
DLLPP PPrroojjeeccttoorr—
—U
Usseerr’’ss M
Maannuuaall
XGA
Screen
Screen Height
(H)
-10%
100%
50%xH
+50%
Distance
(L)
XGA
1080P
Screen
Screen Height
(H)
-20%
20%xH
100%
0%
60%xH
Hx10%
+60%
Distance
(L)
1080P
– 19 –
DLP Projector—User’s Manual
Adjusting the horizontal image position
With the lens in the center position the horizontal image position can be adjusted to the left or right
by up to a maximum of 5% of the image width. Note that the maximum horizontal image height
adjustment can be limited by the vertical image position. For example it is not possible to achieve
the maximum horizontal image position if the vertical image position is at maximum. Please
consult the Shift Range diagram below for further clarification.
Wx5%
Wx5%
Shift Range Diagram
WUXGA and WXGA
When W and H at 0% offset position
The max. H up shift=Hx55%
The max. H down shift=Hx15%
The max. W shift=Wx5%
When max. W shift is Wx5%
max. H shift=Hx50%
When max. H shift is Hx55%
max. W shift=Hx0%
— 20 —
D
DLLPP PPrroojjeeccttoorr—
—U
Usseerr’’ss M
Maannuuaall
XGA
When W and H at 0% offset position
The max. H up shift=Hx50%
The max. H down shift=Hx10%
The max. W shift=Wx5%
When max. W shift is Wx5%
max. H shift=Hx45%
When max. H shift is Hx50%
max. W shift=Hx0%
1080P
When W and H at 0% offset position
The max. H up shift=Hx60%
The max. H down shift=Hx20%
The max. W shift=Wx5%
When max. W shift is Wx5%
max. H shift=Hx55%
When max. H shift is Hx60%
max. W shift=Hx0%
– 21 –
DLP Projector—User’s Manual
Adjusting the Zoom, Focus and Keystone
1.
Use the Image-zoom
control (on the projector
only) to resize the
projected image and
screen size.
2.
Use the Image-focus
control (on the projector
only) to sharpen the
projected image.
3.
Use the KEYSTONE
buttons (on the
projector or the remote
control) to correct
image-trapezoid (wider
top or bottom)
effect.
Remote control and OSD panel
4.
The keystone control
appears on the display.
— 22 —
D
DLLPP PPrroojjeeccttoorr—
—U
Usseerr’’ss M
Maannuuaall
Adjusting the Volume
1.
Press the Volume +/buttons on the remote
control.
The volume control
appears on the display.
2.
Press the Left or Right
Cursor buttons on the
keypad to adjust
Volume +/-.
3.
Press the MUTE button
to turn off the volume
(This feature is
available only on the
remote).
– 23 –
DLP Projector—User’s Manual
ON-SCREEN DISPLAY (OSD) MENU SETTINGS
OSD Menu Controls
The projector has an OSD that lets you make image adjustments and change various settings.
Navigating the OSD
You can use the remote control cursor buttons or the buttons on the top of the projector to
navigate and make changes to the OSD. The following illustration shows the corresponding
buttons on the projector.
3
1
1
3
5
6
7
1
7
4
2
2
5
4
6
1
1. To enter the OSD, press the MENU
button.
2. There are three menus. Press the cursor
◄► button to move through the menus.
3. Press the cursor ▲▼ button to move up
and don in a menu.
4. Press ◄► to change values for settings.
5. Press MENU to close the OSD or leave
a submenu.
Note:
Depending on the video source, not all items in the OSD are available. For example, the
Horizontal/Vertical Position items in the Computer menu can only be modified when
connected to a PC. Items that are not available cannot be accessed and are grayed out.
— 24 —
D
DLLPP PPrroojjeeccttoorr—
—U
Usseerr’’ss M
Maannuuaall
Setting the OSD Language
Set the OSD language to your preference before continuing.
1. Press the MENU button. Press the cursor ◄► button to navigate to Settings 1. Press
the cursor ▲▼ button to move to the Advanced 1 menu.
2. Press
(Enter) / ► to enter the Advanced 1 sub menu. Press the cursor ▲▼ button
until Language is highlighted.
3. Press the cursor button until the language you want is highlighted.
4. Press the MENU button four times to close the OSD.
– 25 –
DLP Projector—User’s Manual
OSD Menu Overview
Use the following illustration to quickly find a setting or determine the range for a setting.
Image
Display Mode
Presentation, Bright, Game, Movie, TV, sRGB, BlackBoard, User1, User2
Brightness
Contrast
Computer
Horizontal Position
Vertical Position
Frequency
Tracking
Auto Sync
Off, On
Auto Image
Advanced
Brilliant Color
Sharpness
Gamma
1.8, 2.0, 2.2, 2.4, B&W, Linear
Color Temperature
Warm, Normal, Cold
Video AGC
Off, On
Video Saturation
Video Tint
Color Manager
Red
Hue
Saturation
Gain
Green
Hue
Saturation
Gain
Blue
Hue
Saturation
Gain
Cyan
Hue
Saturation
Gain
Magenta
Hue
Saturation
Gain
Yellow
Hue
Saturation
Gain
White
Red
Green
Blue
Settings 1
Source
Source
Reference Input Source Select (IR/Keypad)
Projection
Normal, Real, Ceiling, Real+Ceiling
Aspect Ratio
Fill, 4:3, 16:9, Letter Box, Native, 2.35:1
Keystone
Digital Zoom
Audio
Volume
Advanced 1
Language
Off, On
Mute
English, Français, Español, Deutsch, Português, 簡体中文, 繁體中文, Italiano,
Svenska, Nederlands, Suomi, Ελληνικά, Norsk, Polski, Русский, 한국어, 日本語,
, Magyar,
, Türkçe, Čeština, Việt,
,
Off, On
Security Lock
Blank Screen
Blank, Red, Green, Blue, White
Splash Logo
Off, On
Closed Captioning
Off, On
Keypad Lock
Off, On
3D
3D Setting
3D Sync Invert
3D Format
Screen Capture
Advanced 2
Test Pattern
Off, DLP-Link, IR
Off, On
Frame Sequential, Top/Bottom, Side-By-Side, Frame
Packing (3D FramePacking HDMI source only)
None, Grid, White, Red, Green, Blue, Black
H Image Shift
V Image Shift
Settings 2
Auto Source
Off, On
No Signal Power Off
Auto Power On
Off, On
Lamp Mode
ECO , Normal
Reset All
Status
Active Source
Video Information
Lamp Hours(ECO , Normal, Abnormal)
Software Version
Serial Number
Advanced 1
Menu Position
Translucent Menu
Low Power Mode
Fan Speed
Center, Down, Up, Left, Right
0%, 25%, 50%, 75%, 100%
Off, Low Power, Power On by LAN, VGA Out
Normal, High
Lamp Hour Reset
Projector ID
00-98
Network
Network State
Projection Angle Caution
Advanced 2
Connect, Disconnect
DHCP
Off, On
IP Address
0~255, 0~255, 0~255, 0~255
Subnet Mask
0~255, 0~255, 0~255, 0~255
Gateway
0~255, 0~255, 0~255, 0~255
DNS
0~255, 0~255, 0~255, 0~255
Apply
OK / Cancel
Off, On
Sleep Timer
Source Filter
— 26 —
DVI
Disable, Enable
HDMI
Disable, Enable
DisplayPort
Disable, Enable
VGA1
Disable, Enable
VGA2
Disable, Enable
BNC
Disable, Enable
Component Video
Disable, Enable
S-Video
Disable, Enable
Composite Video
Disable, Enable
D
DLLPP PPrroojjeeccttoorr—
—U
Usseerr’’ss M
Maannuuaall
Image Menu
Attention !
All of display mode parameters when changed will be saved to user mode.
Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the
Image Menu. Press the cursor ▲▼ button to move up and down in the Image menu. Press ◄►
to enter and change values for settings.
ITEM
DESCRIPTION
Display Mode
Press the cursor ◄► button to enter and set the Display Mode.
Brightness
Press the cursor ◄► button to enter and adjust the display brightness.
Contrast
Press the cursor ◄► button to enter and adjust the display contrast.
Computer
Press
Auto Image
Press
(Enter) / ► to automatically adjustment for phase, tracking, size and
position.
Advanced
Press
29.
Color Manager
Press
(Enter) / ► to enter the color manager menu. See page 30 for more
information on Color Manager.
(Enter) / ► to enter the Computer menu. See Computer Menu on page 28.
(Enter) / ► to enter the Advanced menu. See Advanced Feature on page
– 27 –
DLP Projector—User’s Manual
Computer Menu
Press the MENU button to open the OSD menu. Press ◄► to move to the Image menu. Press
▲▼ to move to the Computer menu and then press Enter or ►. Press ▲▼ to move up and
down in the Computer menu.
ITEM
DESCRIPTION
Horizontal Position
Press the cursor ◄► button to enter and adjust the display position to left or right.
Vertical Position
Press the cursor ◄► button to enter and adjust the display position to up or down.
Frequency
Press the cursor ◄► button to enter and adjust the A/D sampling clock.
Tracking
Press the cursor ◄► button to enter and adjust the A/D sampling dot.
Auto Sync
Press the cursor ◄► button to enter and enable or disable the autolock control for
RGB source.
— 28 —
D
DLLPP PPrroojjeeccttoorr—
—U
Usseerr’’ss M
Maannuuaall
Advanced Feature
Press the Menu button to open the OSD menu. Press ◄► to move to the Image menu. Press
▼▲ to move to the Advanced menu and then press Enter or ►. Press ▼▲ to move up and
down in the Advanced menu.
ITEM
DESCRIPTION
Brilliant Color
Press the cursor ◄► button to enter and adjust the Brilliant Color value.
Sharpness
Press the cursor ◄► button to enter and adjust the display sharpness.
Gamma
Press the cursor ◄► button to enter and adjust the gamma correction of the display.
Color Temperature
Press the cursor ◄► button to enter and adjust the color temperature.
Video AGC
Press the cursor ◄► button to enter and enable or disable the Automatic Gain Control
for video source.
Video Saturation
Press the cursor ◄► button to enter and adjust the video saturation.
Video Tint
Press the cursor ◄► button to enter and adjust the video tint/hue.
– 29 –
DLP Projector—User’s Manual
Color Manager
Press the Menu button to open the OSD menu. Press ◄► to move to the Image menu. Press
▼▲ to move to the Color Manager menu and then press Enter or ►. Press ▼▲ to move up and
down in the Color Manager menu.
ITEM
DESCRIPTION
Red
Select to enter the Red Color Manager.
Press the ◄► buttons to adjust the Hue, Saturation, and Gain.
Green
Select to enter the Green Color Manager.
Press the ◄► buttons to adjust the Hue, Saturation, and Gain.
Blue
Select to enter the Blue Color Manager.
Press the ◄► buttons to adjust the Hue, Saturation, and Gain.
Cyan
Select to enter the Cyan Color Manager.
Press the ◄► buttons to adjust the Hue, Saturation, and Gain.
Magenta
Select to enter the Magenta Color Manager.
Press the ◄► buttons to adjust the Hue, Saturation, and Gain.
Yellow
Select to enter the Yellow Color Manager.
Press the◄► buttons to adjust the Hue, Saturation, and Gain.
White
Select to enter the White Color Manager.
Press the ◄► buttons to adjust the Red, Green, and Blue.
— 30 —
D
DLLPP PPrroojjeeccttoorr—
—U
Usseerr’’ss M
Maannuuaall
Settings 1 Menu
Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the
Settings 1 menu. Press the cursor ▲▼ button to move up and down in the Settings 1 menu.
Press ◄► to enter and change values for settings.
ITEM
DESCRIPTION
Source
Press
(Enter) / ► to enter the Source menu. Reference input Source select
(IR / Keypad).
Projection
Press the cursor ◄► button to enter and choose from four projection methods:
Aspect Ratio
Press the cursor ◄► button to enter and adjust the video aspect ratio.
Keystone
Press the cursor ◄► button to enter and adjust the display keystone.
Digital Zoom
Press the cursor ◄► button to enter and adjust the Digital Zoom menu.
Audio
Press
Advanced 1
Press
(Enter) / ► to enter the Advanced 1 menu. See Advanced 1 Feature on
page 33.
Advanced 2
Press
(Enter) / ► to enter the Advanced 2 menu. See Advanced 2 Feature on
page 35.
(Enter) / ► to enter the Audio menu. See Audio on page 32.
– 31 –
DLP Projector—User’s Manual
Audio
Press the Menu button to open the OSD menu. Press ◄► to move to the Settings 1 menu.
Press ▼▲ to move to the Audio menu and then press Enter or ►. Press ▼▲ to move up and
down in the Audio menu.
ITEM
DESCRIPTION
Volume
Press the cursor ◄► button to enter and adjust the audio volume.
Mute
Press the cursor ◄► button to enter and turn on or off the speaker.
— 32 —
D
DLLPP PPrroojjeeccttoorr—
—U
Usseerr’’ss M
Maannuuaall
Advanced 1 Feature
Press the Menu button to open the OSD menu. Press ◄► to move to the Settings 1 menu.
Press ▲▼ to move to the Advanced 1 menu and then press Enter or ►. Press ▲▼ to move up
and down in the Advanced 1 menu. Press ◄► to enter and change values for setting.
ITEM
DESCRIPTION
Language
Press the cursor ◄► button to enter and select a different localization Menu.
Security Lock
Press the cursor ◄► button to enter and enable or disable security lock function.
Blank Screen
Press the cursor ◄► button to enter and select different color to blank the screen.
Splash Logo
Press the cursor ◄► button to enter and select splash logo on or off.
Closed Captioning
Press the cursor ◄► button to enter and enable or disable Closed Captioning
Keypad Lock
Press the cursor ◄► button to enter and enable or disable keys can be work on
keypad.
3D Setting
Press
Setting.
Screen Capture
Press
(Enter) / ► to capture screen, and please wait saving picture.
Picture will auto showing after next power on.
(Enter) / ► to enter the 3D menu. See page 34 for more information on 3D
Note:
To enjoy the 3D function, first enable the Play Movie in 3D setting found in your DVD device under
the 3D Disc Menu.
– 33 –
DLP Projector—User’s Manual
3D Setting
ITEM
DESCRIPTION
3D
Press the cursor ◄► button to enter and select different 3D mode.
3D Sync Invert
Press the cursor ◄► button to enter and enable or disable 3D Sync Invert.
3D Format
Press the cursor ◄► button to enter and enable or disable different 3D Format.
Note:
1. The 3D OSD menu item is gray if there is no appropriate 3D source. This is the default setting.
2. When the projector is connected to an appropriate 3D source, the 3D OSD menu item is enabled
for selection.
3. Use 3D glasses to view a 3D image.
4. You need 3D content from a 3D DVD or 3D media file.
5. You need to enable the 3D source (some 3D DVD content may have a 3D on-off selection
feature).
6. You need DLP link 3D or IR 3D shutter glasses. With IR 3D shutter glasses, you need to install a
driver on your PC and connect a USB emitter.
7. The 3D mode of the OSD needs to match the type of glasses (DLP link or IR 3D).
8. Power on the glasses. Glasses normally have a power on -off switch.
Each type of glasses has their own configuration instructions. Please follow the configuration
instructions that come with your glasses to finish the setup process.
Note:
Since different types of glass (DLP link or IR shutter glass) have their own setting instructions,
Please follow the guide to finish the setup process.
— 34 —
D
DLLPP PPrroojjeeccttoorr—
—U
Usseerr’’ss M
Maannuuaall
Advanced 2 Feature
Press the Menu button to open the OSD menu. Press ◄► to move to the Settings 1 menu.
Press ▲▼ to move to the Advanced 2 menu and then press Enter or ►. Press ▲▼ to move up
and down in the Advanced 2 menu. Press ◄► to enter and change values for setting.
ITEM
DESCRIPTION
Test Pattern
Press the cursor ◄► button to enter and select internal test pattern.
H Image Shift
Press the cursor ◄► button to enter and select H Image Shift.
V Image Shift
Press the cursor ◄► button to enter and select V Image Shift.
– 35 –
DLP Projector—User’s Manual
Settings 2 Menu
Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the
Settings 2 menu. Press the cursor ▲▼ button to move up and down in the Settings 2 menu.
ITEM
DESCRIPTION
Auto Source
Press the cursor ◄► button to enter and enable or disable automatic source
detection.
No Singal Power
Off (min.)
Press the cursor ◄► button to enter and enable or disable automatic shutdown of
lamp when no signal.
Auto Power On
Press the cursor ◄► button to enter and enable or disable automatic power On when
AC power is supplied.
Lamp Mode
Press the cursor ◄► button to enter and select the lamp mode for higher brightness
or lower brightness to save lamp life.
Reset All
Press
(Enter) / ► to reset all settings to default values.
Status
Press
Status.
(Enter) / ► to enter the Status menu. See page 37 for more information on
Advanced 1
Press
(Enter) / ► to enter the Advanced 1 menu. See Advanced 1 Feature on
page 38.
Advanced 2
Press
(Enter) / ► to enter the Advanced 2 menu. See Advanced 2 Feature on
page 50.
— 36 —
D
DLLPP PPrroojjeeccttoorr—
—U
Usseerr’’ss M
Maannuuaall
Status
Press the cursor ▲▼ button to move up and down in the Settings 2 menu. Select the Status
menu and press Enter or ► to enter.
ITEM
DESCRIPTION
Active Source
Display the activated source.
Video Information
Displays resolution/video information for RGB source and color standard for Video
source.
Lamp Hours
Lamp hour used information is displayed. (ECO, Normal, Abnormal )
Software Version
Showing system software version.
Serial Number
Showing serial number of this projector.
– 37 –
DLP Projector—User’s Manual
Advanced 1 Feature
Press the Menu button to open the OSD menu. Press ◄► to move to the Settings 2 menu.
Press ▲▼ to move to the Advanced 1 menu and then press Enter or ►. Press ▲▼ to move up
and down in the Advanced 1 menu. Press ◄► to enter and change values for setting.
ITEM
DESCRIPTION
Menu Position
Press the cursor ◄► button to enter and select different OSD location.
Translucent Menu
Press the cursor ◄► button to enter and select OSD background translucent level.
Low Power Mode
Press the cursor ◄► button to enter and turn Low Power Mode on or off.
Fan Speed
Press the cursor ◄► button to enter and toggle between Normal and High fan speeds.
Note: We recommend selecting high speed in high temperatures, high humidity, or
high altitude (higher than 1500m/4921ft) areas.
Lamp Hour Reset
After replacing the lamp, this item should be reset. See page 39 for more information
on Lamp Hour Reset.
Projector ID
Network
Projection Angle
Caution
Press the cursor ◄► button to enter and adjust a two digit projector ID from 00
through 98.
Press
(Enter) / ► to enter the Network menu. See page 39 for more information on
Network.
Press the cursor ◄► button to enter and turn Projection Angle Caution on or off.
— 38 —
D
DLLPP PPrroojjeeccttoorr—
—U
Usseerr’’ss M
Maannuuaall
Lamp Hour Reset
Please refer to Resetting the Lamp on page 57 to reset the lamp hour counter.
Network
ITEM
DESCRIPTION
Network State
Displays the network connection status.
DHCP
Press the cursor ◄► button to turn DHCP On or Off.
Note: If you select DHCP Off, complete the IP Address, Subnet Mask, Gateway,
and DNS fields.
IP Address
Enter a valid IP address if DHCP is turned off.
Subnet Mask
Enter a valid Subnet Mask if DHCP is turned off.
Gateway
Enter a valid Gateway address if DHCP is turned off.
DNS
Enter a valid DNS name if DHCP is turned off.
Apply
Press
(Enter) / ► to confirm settings.
– 39 –
DLP Projector—User’s Manual
LAN_RJ45
Wired LAN Terminal functionalites
Remote control and monitoring of a projector from a PC (or Laptop) via wired LAN is also possible.
Compatibility with Crestron / AMX (Device Discovery) / Extron control boxes enables not only
collective projector management on a network but also management from a control panel on a PC
(or Laptop) browser screen.

Crestron is a registered trademark of Crestron Electronics, Inc. of the United States.

Extron is a registered trademark of Extron Electronics, Inc. of the United States.

AMX is a registered trademark of AMX LLC of the United States.

PJLink applied for trademark and logo registration in Japan, the United States of America, and
other countries by JBMIA.
Supported External Devices
This projector is supported by the specified commands of the Crestron Electronics controller and
related software (ex, RoomView ® ).
http://www.crestron.com/
This projector is supported by AMX ( Device Discovery ).
http://www.amx.com/
This projector is compliant to support Extron device(s) for reference.
http://www.extron.com/
This projector supports all commands of PJLink Class1 (Version 1.00).
http://pjlink.jbmia.or.jp/english/
For more detail of information about the diverse types of external devices which can be connected to
the LAN/RJ45 port and remote/control the projector, as well as the related control commands
supporting for each external device, kindly please get contact with the Support-Service team directly.
— 40 —
D
DLLPP PPrroojjeeccttoorr—
—U
Usseerr’’ss M
Maannuuaall
LAN_RJ45
1. Connect an RJ45 cable to RJ45 ports on the projector and the PC (Laptop).
2. On the PC (Laptop), select Start → Control Panel → Network Connections.
– 41 –
DLP Projector—User’s Manual
3. Right-click on Local Area Connection, and select Properties.
4. In the Properties window, select the General tab, and select Internet Protocol (TCP/IP).
5. Click Properties.
6. Click Use the following IP address and fill in the IP address and Subnet mask, then click OK.
— 42 —
D
DLLPP PPrroojjeeccttoorr—
—U
Usseerr’’ss M
Maannuuaall
7. Press the Menu button on the projector.
8.
Select Settings2→ Advanced1 → Network
9.
After getting into Network, input the following:
 DHCP: Off
 IP Address: 10.10.10.10
 Subnet Mask: 255.255.255.0
 Gateway: 0.0.0.0
 DNS Server: 0.0.0.0
10. Press
(Enter) / ► to confirm settings.
Open a web browser
(for example, Microsoft Internet Explorer with Adobe Flash Player 9.0 or higher).
11. In the Address bar, input the IP address: 10.10.10.10.
12. Press
(Enter) / ►.
The projector is setup for remote management. The LAN/RJ45 function displays as follows.
– 43 –
DLP Projector—User’s Manual
CATEGORY
Crestron Control
Projector
Network Configuration
User Password
Admin Password
ITEM
INPUT-LENGTH
IP Address
15
IP ID
3
Port
5
Projector Name
10
Location
10
Assigned To
10
DHCP (Enabled)
(N/A)
IP Address
15
Subnet Mask
15
Default Gateway
15
DNS Server
15
Enabled
(N/A)
New Password
10
Confirm
10
Enabled
(N/A)
New Password
10
Confirm
10
For more information, please visit http://www.crestron.com.
— 44 —
D
DLLPP PPrroojjeeccttoorr—
—U
Usseerr’’ss M
Maannuuaall
Preparing Email Alerts
1. Make sure that user can access the homepage of LAN RJ45 function by web browser (for example, Microsoft Internet Explorer v6.01/v8.0).
2. From the Homepage of LAN/RJ45, click Alert Settings.
3. By default, these input boxes in Alert Settings are blank.
– 45 –
DLP Projector—User’s Manual
4. For Sending alert mail, input the following:
SMTP field is the mail server for sending out email (SMTP protocol). This is a required
field.
To field is the recipient’s email address (for example, the projector administrator). This
is a required field.
Cc field sends a carbon copy of the alert to the specified email address. This is an
optional field (for example, the projector administrator’s assistant).
From field is the sender’s email address (for example, the projector administrator). This
is a required field.
e alert conditions by checking the desired boxes.
Note: Fill in all fields as specified. User can click Send Test Mail to test what setting is correct.
For successful sending an e-mail alert, you must select alert conditions and enter a correct e-mail
address.
— 46 —
D
DLLPP PPrroojjeeccttoorr—
—U
Usseerr’’ss M
Maannuuaall
RS232 by Telnet Function
Besides projector connected to RS232 interface with “Hyper-Terminal” communication by
dedicated RS232 command control, there is alternative RS232 command control way, so called
“RS232 by TELNET” for LAN/RJ45 interface.
Quick Start-Guide for “RS232 by TELNET”
Check and get the IP-Address on OSD of the projector.
Make sure that laptop/PC can access the web-page of the projector.
Make sure that “Windows Firewall” setting to be disabled in case of “TELNET” function filtering
out by laptop/PC.
Start => All Programs => Accessories => Command Prompt
– 47 –
DLP Projector—User’s Manual
Input the command format like the below:
telnet ttt.xxx.yyy.zzz 23 (“Enter” key pressed)
(ttt.xxx.yyy.zzz: IP-Address of the projector)
If Telnet-Connection ready, and user can have RS232 command input, then “Enter” key
pressed, the RS232 command will be workable.
How to have TELNET enabled in Windows VISTA / 7
By default installation for Windows VISTA, “TELNET” function is not included. But end-user
can have it by way of “Turn Windows features On or Off” to be enabled.
Open “Control Panel” in Windows VISTA
Open “Programs”
— 48 —
D
DLLPP PPrroojjeeccttoorr—
—U
Usseerr’’ss M
Maannuuaall
Select “Turn Windows features on or off” to open
Have “Telnet Client” option checked, then press “OK” button.
Specsheet for “RS232 by TELNET” :
1. Telnet: TCP
2. Telnet port: 23
(for more detail, kindly please get contact with the service agent or team)
3. Telnet utility: Windows “TELNET.exe” (console mode)
4. Disconnection for RS232-by-Telnet control normally: Close Windows Telnet utility directly
after TELNET connection ready
5. Limitation 1 for Telnet-Control: there is less than 50 bytes for successive network payload
for Telnet-Control application.
Limitation 2 for Telnet-Control: there is less than 26 bytes for one complete RS232
command for Telnet-Control.
Limitation 3 for Telnet-Control: Minimum delay for next RS232 command must be more
than 200 (ms).
(*, In Windows XP built-in “TELNET.exe” utility, “Enter” key pressed will have “CarriageReturn” and “New-Line” code.)
– 49 –
DLP Projector—User’s Manual
Advanced 2 Feature
Press the Menu button to open the OSD menu. Press ◄► to move to the Settings 2 menu.
Press ▲▼ to move to the Advanced 2 menu and then press Enter or ►. Press ▲▼ to move up
and down in the Advanced 2 menu. Press ◄► to enter and change values for setting.
ITEM
DESCRIPTION
Sleep Timer (min)
Press the cursor ◄► button to enter and set Sleep timer. The projector automatically
turns off after the preset period of time.
Source Filter
Press
(Enter) / ► to enter the Source Filter menu. See page 51 for more
information on Source Filter.
— 50 —
D
DLLPP PPrroojjeeccttoorr—
—U
Usseerr’’ss M
Maannuuaall
Source Filter
Press the ENTER button to enter the Source Filter sub menu.
ITEM
DESCRIPTION
DVI
Press the ◄► buttons to enter and enable or disable the DVI source.
HDMI
Press the ◄► buttons to enter and enable or disable the HDMI source.
DisplayPort
Press the ◄► buttons to enter and enable or disable the DisplayPort source.
VGA1
Press the ◄► buttons to enter and enable or disable the VGA1 source.
VGA2
Press the ◄► buttons to enter and enable or disable the VGA2 source.
BNC
Press the ◄► buttons to enter and enable or disable the BNC source.
Component Video
Press the ◄► buttons to enter and enable or disable the Component Video source.
S-Video
Press the ◄► buttons to enter and enable or disable the S-Video source.
Composite Video
Press the ◄► buttons to enter and enable or disable the Composite Video source.
– 51 –
DLP Projector—User’s Manual
MAINTENANCE AND SECURITY
Tilt Up/Down caution

When projector detect angle is over spec, popup caution message.
The model with Tilt lamp module
The model with Tilt lamp module can be used projection angle as shown below.
With the tilt lamp fitted the projector can tilt upwards any angle but not tilt downwards more than
15 degrees.
If Projector projection angle exceeds the drawing shown and don’t use standard lamp module.
Showing caution message for 5sec and then disappear, projector remain on. (every time when
projector on ; This function can be disable see Advanced 1 Feature on page 38 )
Tilt Lamp
Standard Lamp
The model with Standard lamp module
The model with Standard lamp module can be used projection angle as shown below.
With the standard lamp fitted the projector can tilt downwards any angle but not tilt upwards more
than 15 degrees.
If Projector projection angle exceeds the drawing shown and don’t use tilt lamp module. Showing caution
message for 5sec and then disappear, projector remain on. (every time when projector on ; This function
can be disable see Advanced 1 Feature on page 38 )
Warning:
Your operation might cause lamp defect and life decay. If used incorrect lamp module
— 52 —
D
DLLPP PPrroojjeeccttoorr—
—U
Usseerr’’ss M
Maannuuaall
Standard lamp module
Tilt lamp module
( Optional )
Note:
The standard lamp is to go with regular shipment for normal operation and the tilt lamp is an
option lamp for abnormal operation
– 53 –
DLP Projector—User’s Manual
Replacing the Projection Lamp
The projection lamp should be replaced when it burns out. It should only be replaced with a
certified replacement part, which you can order from your local dealer.
Important:
a. The projection lamp used in this product contains a small amount of mercury.
b. Do not dispose this product with general household waste.
c. Disposal of this product must be carried out in accordance with the regulations of your local
authority.
Warning:
Be sure to turn off and unplug the projector at least 30 minutes before replacing the lamp.
Failure to do so could result in a severe burn.
Caution:
In rare cases the lamp bulb may burn out during normal operation and cause glass dust or
shards to be discharged outward from the rear exhaust vent.
Do not inhale or do not touch glass dust or shards. Doing so could result in injury.
Always keep your face away from the exhaust vent so that you do not suffer from the gas and
broken shards of the lamp.
When removing the lamp from a ceiling-mounted projector, make sure that no one is under the
projector. Glass fragments could fall if the lamp has been burned out.
IF A LAMP EXPLODES
If a lamp explodes, the gas and broken shards may scatter inside the projector and they may
come out of the exhaust vent. The gas contains toxic mercury.
Open windows and doors for ventilation.
If you inhale the gas or the shards of the broken lamp enter your eyes or mouth, consult the
doctor immediately.
1.
Switch off the power to the
projector by pressing the
POWER button.
2.
Allow the projector to cool
down at least 30 minutes.
3.
Disconnect the power
cord.
— 54 —
D
DLLPP PPrroojjeeccttoorr—
—U
Usseerr’’ss M
Maannuuaall
4.
Unlock the lamp cover.
5.
Pull up and remove the
cover.
6.
Use a screwdriver to
remove the screws from
the lamp module.
7.
Pull out the lamp module.
– 55 –
DLP Projector—User’s Manual
8.
Reverse steps 1 to 7 to
install the new lamp
module.
While installing, align the
lamp module with the
connector and ensure it is
level to avoid damage.
Note:
The lamp module must sit
securely in place and the
lamp connector must be
connected properly before
tightening the screws.
— 56 —
D
DLLPP PPrroojjeeccttoorr—
—U
Usseerr’’ss M
Maannuuaall
Resetting the Lamp
After replacing the lamp, you should reset the lamp hour counter to zero. Refer to the following:
1.
Press the MENU button to open
the OSD menu.
2.
Press the cursor ◄► button to
move to the Settings 2 menu.
Press the cursor button to move
down to Advanced 1 and press
enter.
3.
Press the cursor ▼▲ button to
move down to Lamp Hour Reset.
4.
Press the cursor ► or Enter
button.
A message screen appears.
5.
Press ▼▲◄► buttons to reset
the lamp hour.
6.
Press the MENU button to get
back to Settings 2.
– 57 –
DLP Projector—User’s Manual
Cleaning the filter (filter: optional parts)
The air filter prevents dust from accumulating on the surface of the optical elements inside the
projector. If the filter is dirty or clogged, your projector may overheat or degrading the projected
image quality.
1.
Turn off the projector, and
unplug the AC power cord
from the AC outlet.
2.
Cleaning the filter with a
vacuum cleaner.
Caution:
Recommend avoiding dusty or smoky environments when you operate the projector, it may
cause poor image quality.
If the filter is heavily clogged and unable to clean, replace a new filter.
Note:
Using a ladder is recommended to access the filter. Do not remove the projector from the
wall mount.
— 58 —
D
DLLPP PPrroojjeeccttoorr—
—U
Usseerr’’ss M
Maannuuaall
Replacing the Filter
1.
Turn off the projector, and
unplug the AC power cord
from the AC outlet.
Clean up the dust on the
projector and around the
air vents.
Pull out the filter cover and
remove from the projector
2.
Lift the filter from the filter
cover.
3.
Replace a new filter
module or replace filter into
cover.
4.
Replace the filter cover
back to the projector by
pushing gently in the
direction shown.
Warning:
Do not wash the filter with the water or other liquid matter
Important:
When the lamp is replaced, the filter should also be replaced, not cleaned.
– 59 –
DLP Projector—User’s Manual
Cleaning the Projector
Cleaning the projector to remove dust and grime will help ensure trouble-free operation.
Warning:
1. Be sure to turn off and unplug the projector at least 30 minutes before cleaning. Failure to do
so could result in a severe burn.
2. Use only a dampened cloth when cleaning. Do not allow water to enter the ventilation
openings on the projector.
3. If a little water gets into the projector interior while cleaning, leave unplugged in a wellventilated room for several hours before using.
4. If a lot of water gets into the projector interior when cleaning, have the projector serviced.
Cleaning the Lens
You can purchase optic lens cleaner from most camera stores. Refer to the following to clean the
projector lens.
1. Apply a little optic lens cleaner to a clean soft cloth. (Do not apply the cleaner directly
to the lens.)
2. Lightly wipe the lens in a circular motion.
Caution:
1. Do not use abrasive cleaners or solvents.
2. To prevent discoloration or fading, avoid getting cleaner on the projector case.
Cleaning the Case
Refer to the following to clean the projector case.
1. Wipe off dust with a clean dampened cloth.
2. Moisten the cloth with warm water and mild detergent (such as used to wash dishes),
and then wipe the case.
3. Rinse all detergent from the cloth and wipe the projector again.
Caution:
To prevent discoloration or fading of the case, do not use abrasive alcohol-based cleaners.
— 60 —
D
DLLPP PPrroojjeeccttoorr—
—U
Usseerr’’ss M
Maannuuaall
Using the Physical Lock
Using the Kensington® Lock
If you are concerned about security, attach the projector to a permanent object with the
Kensington slot and a security cable.
Note:
Contact your vendor for details on purchasing a suitable Kensington security cable.
The security lock corresponds to Kensington’s MicroSaver Security System. If you have any
comment, contact: Kensington, 2853 Campus Drive, San Mateo, CA 94403, U.S.A. Tel: 800535-4242, http://www.Kensington.com.
Using the Security Chain Lock
In addition to the password protection function and the Kensington lock, the Security Chain
Opening helps protect the PROJECTOR from unauthorized use.
See the following picture.
– 61 –
DLP Projector—User’s Manual
TROUBLESHOOTING
Common problems and solutions
These guidelines provide tips to deal with problems you may encounter while using the projector.
If the problem remains unsolved, contact your dealer for assistance.
Often after time spent troubleshooting, the problem is traced to something as simple as a loose
connection. Check the following before proceeding to the problem-specific solutions.

Use some other electrical device to confirm that the electrical outlet is working.

Ensure the projector is turned on.

Ensure all connections are securely attached.

Ensure the attached device is turned on.

Ensure a connected PC is not in suspending mode.

Ensure a connected notebook computer is configured for an external display.
(This is usually done by pressing an Fn-key combination on the notebook.)
Tips for Troubleshooting
In each problem-specific section, try the steps in the order suggested. This may help you to solve
the problem more quickly.
Try to pin point the problem and thus avoid replacing non-defective parts.
For example, if you replace batteries and the problem remains, put the original batteries back and
go to the next step.
Keep a record of the steps you take when troubleshooting: The information may be useful when
calling for technical support or for passing on to service personnel.
— 62 —
D
DLLPP PPrroojjeeccttoorr—
—U
Usseerr’’ss M
Maannuuaall
LED Error Messages
POWER LED
RED
BLUE
ERROR CODE MESSAGES
TEMP LED
RED
READY LED
RED
Flash
-
OFF
OFF
ON
-
OFF
OFF
Flash
-
OFF
OFF
Lamp Lit , System stable
ON
OFF
ON
Cooling
Flash
-
OFF
OFF
ON
-
ON
OFF
Thermal Break Sensor error
4 blinks
-
OFF
OFF
Lamp Fail
5 blinks
-
OFF
ON
Lamp Temperature shut down
5 blinks
-
OFF
1 blinks
Lamp Short circuit in output detected
5 blinks
-
OFF
2 blinks
Lamp End of lamp life detected
5 blinks
-
OFF
3 blinks
Lamp did not ignite
5 blinks
-
OFF
4 blinks
Lamp extinguished during normal operation
5 blinks
-
OFF
5 blinks
Lamp extinguished during run-up phase
5 blinks
-
OFF
6 blinks
Lamp voltage got error
5 blinks
-
OFF
7 blinks
Lamp ballast got error
Ballast watt value is out of range
(Lamp Normal & Eco mode)
Lamp ballast Communication error
5 blinks
-
OFF
8 blinks
5 blinks
-
OFF
9 blinks
5 blinks
-
OFF
10 blinks
Lamp ballast power error
5 blinks
-
OFF
11 blinks
6 blinks
-
OFF
1 blinks
Fan-2 error
6 blinks
-
OFF
2 blinks
Fan-3 error
6 blinks
-
OFF
3 blinks
Fan-4 error
6 blinks
-
OFF
4 blinks
Fan-5 error
6 blinks
-
OFF
5 blinks
Case Open
7 blinks
-
OFF
OFF
DAD1000 error
8 blinks
-
OFF
OFF
System Initial
Ready to Power on (Standby)
System Power on
Over Temperature
Fan-1 error
-
Color wheel error
9 blinks
OFF
OFF
In the event of an error, please disconnect the AC power cord and wait for one (1) minute before
restarting the projector. If the Power or Ready LEDs are still blinking or any other situation that isn't
listed in the chart above, please contact your service center.
Image Problems
Problem: No image appears on the screen
1. Verify the settings on your notebook or desktop PC.
2. Turn off all equipment and power up again in the correct order.
Problem: The image is blurred
1. Adjust the Focus on the projector.
2. Press the Auto button on the remote control.
3. Ensure the projector-to-screen distance is within the specified range.
4. Check that the projector lens is clean.
– 63 –
DLP Projector—User’s Manual
Problem: The image is wider at the top or bottom (trapezoid effect)
1. Position the projector so it is as perpendicular to the screen as possible.
2. Use the Keystone button on the remote control to correct the problem.
Problem: The image is reversed
Check the Projection setting on the Settings 1 menu of the OSD.
Problem: The image is streaked
1. Set the Frequency and Tracking settings on the Image->Computer menu of the OSD to
the default settings.
2. To ensure the problem is not caused by a connected PC’s video card, connect to another
computer.
Problem: The image is flat with no contrast
Adjust the Contrast setting on the Image menu of the OSD.
Problem: The color of the projected image does not match the source image.
Adjust the Color Temperature and Gamma settings on the Image->Advanced menu of the
OSD.
Lamp Problems
Problem: There is no light from the projector
1. Check that the power cable is securely connected.
2. Ensure the power source is good by testing with another electrical device.
3. Restart the projector in the correct order and check that the Power LED is on.
4. If you have replaced the lamp recently, try resetting the lamp connections.
5. Replace the lamp module.
6. Put the old lamp back in the projector and have the projector serviced.
Problem: The lamp goes off
1. Power surges can cause the lamp to turn off. Re-plug power cord. When the Power LED is
on, press the power button.
2. Replace the lamp module.
3. Put the old lamp back in the projector and have the projector serviced.
Remote Control Problems
Problem: The projector does not respond to the remote control
1. Direct the remote control towards remote sensor on the projector.
2. Ensure the path between remote and sensor is not obstructed.
3. Turn off any fluorescent lights in the room.
4. Check the battery polarity.
5. Replace the battery.
6. Turn off other Infrared-enabled devices in the vicinity.
7. Have the remote control serviced.
— 64 —
D
DLLPP PPrroojjeeccttoorr—
—U
Usseerr’’ss M
Maannuuaall
Audio Problems
Problem: There is no sound
1. Adjust the volume on the remote control.
2. Adjust the volume of the audio source.
3. Check the audio cable connection.
4. Test the source audio output with other speakers.
5. Have the projector serviced.
Problem: The sound is distorted
1. Check the audio cable connection.
2. Test the source audio output with other speakers.
3. Have the projector serviced.
Having the Projector Serviced
If you are unable to solve the problem, you should have the projector serviced. Pack the projector
in the original carton. Include a description of the problem and a checklist of the steps you took
when trying to fix the problem: The information may be useful to service personnel. For servicing,
return the projector to the place you purchased it.
– 65 –
DLP Projector—User’s Manual
HDMI Q & A
Q. What is the difference between a “Standard” HDMI cable and a “High-Speed”
HDMI cable?
Recently, HDMI Licensing, LLC announced that cables would be tested as Standard or HighSpeed cables.
˙Standard (or “category 1”) HDMI cables have been tested to perform at speeds of 75Mhz or up
to 2.25Gbps, which is the equivalent of a 720p/1080i signal.
˙High Speed (or “category 2”) HDMI cables have been tested to perform at speeds of 340Mhz or
up to 10.2Gbps, which is the highest bandwidth currently available over an HDMI cable and
can successfully handle 1080p signals including those at increased color depths and/or
increased refresh rates from the Source. High-Speed cables are also able to accommodate
higher resolution displays, such as WQXGA cinema monitors (resolution of 2560 x 1600).
Q. How do I run HDMI cables longer than 10 meters?
There are many HDMI Adopters working on HDMI solutions that extend a cable’s effective
distance from the typical 10 meter range to much longer lengths. These companies manufacture
a variety of solutions that include active cables (active electronics built into cables that boost and
extend the cable’s signal), repeaters, amplifiers as well as CAT5/6 and fiber solutions.
Q. How can I tell if a cable is an HDMI certified cable?
All HDMI products are required to be certified by the manufacturer as part of the HDMI
Compliance Test Specification. However, there may be instances where cables bearing the
HDMI logo are available but have not been properly tested. HDMI Licensing, LLC actively
investigates these instances to ensure that the HDMI trademark is properly used in the market.
We recommend that consumers buy their cables from a reputable source and a company that is
trusted.
For more detail information check http://www.hdmi.org/learningcenter/faq.aspx#49
— 66 —
D
DLLPP PPrroojjeeccttoorr—
—U
Usseerr’’ss M
Maannuuaall
SPECIFICATIONS
Specifications
Model
Display type
Resolution
D5010/D501ZAA/D501ZWAA
D5110W
D5380U
0.7" XGA DC3
0.65" WXGA DC2
0.67" WUXGA DC3 TypeA
1280x800
1920x1200
1024x768
1.5 meters ~ 7 meters
Projection distance
Projection screen size
37.3” ~ 215”
1.6 ~ 2.0
1.62 ~ 2.03
1.54 ~ 1.93
±40°
Vertical keystone correction
Projection methods
36” ~ 210”
Manual Focus/Manual Zoom
Projection lens
Throw ratio
34.3” ~ 200”
Front, Rear, Desktop/Ceiling (Rear, Front)
Data compatibility
VGA, SVGA, XGA, SXGA, SXGA+, UXGA, WUXGA@60hz, Mac
SDTV/EDTV/ HDTV
480i, 576i, 480p, 576p, 720p, 1080i, 1080p
Video compatibility
NTSC (M, 3.58/4.43 MHz), PAL (B, D, G, H, I, M, N), SECAM (B, D, G, K, K1, L)
H-Sync
15, 31-91.4kHz
V-Sync
24~30Hz, 47 ~ 120Hz
Safety certification
FCC-B, cUL, UL, CE, C-tick, CCC, KC, CB, PCT
5° ~ 35°C
Operation temperature
Dimensions
431.11mm (W) x 344.16mm (D) x 180.57mm (H)
AC Universal 100 – 240V
AC Input
Power consumption
Lamp
Typical 480W (boost) , <0.5watts(Stand By)/
Typical 365W(standard) , <0.5watts(Stand By)
370W (Normal) / 280W (Eco)
3W x 2
Audio speaker
VGA x 2
DisplayPort x 1
DVI-D x 1
S-Video x 1
5 BNC (RGBHV) x 1
Input Terminals
Component x 1
Composite video x 1
HDMI x 1
RCA stereo x 2
Mini-jack stereo x 2
VGA x 1
Output Terminals
PC audio out x 1
RS-232C
RJ45
Screen trigger: DC Jack x 1 (DC12V 200mA output function)
wire remote
Control Terminals
USB (type B) only for service/mouse control
USB (type A) only for power supply; WHDI
3D sync
Kensington lock
Security
– 67 –
DLP Projector—User’s Manual
Specifications
Model
Display type
Resolution
D5005
D5290U
0.7" XGA DC3
1024x768
1920x1200
37.3” ~ 215”
35.1” ~ 205”
Manual Focus/Manual Zoom
1.6 ~ 2.0
1.54 ~ 1.93
±40°
Vertical keystone correction
Projection methods
1920x1080
36” ~ 210”
Projection lens
Throw ratio
0.67" WUXGA DC3 TypeA 0.65” 1080P DC2 TypeA
1.5 meters ~ 7 meters
Projection distance
Projection screen size
D5190HD
Front, Rear, Desktop/Ceiling (Rear, Front)
Data compatibility
VGA, SVGA, XGA, SXGA, SXGA+, UXGA, WUXGA@60hz, Mac
SDTV/EDTV/ HDTV
480i, 576i, 480p, 576p, 720p, 1080i, 1080p
Video compatibility
NTSC (M, 3.58/4.43 MHz), PAL (B, D, G, H, I, M, N),
SECAM (B, D, G, K, K1, L)
H-Sync
15, 31-91.4kHz
V-Sync
24~30Hz, 47 ~ 120Hz
Safety certification
FCC-B, cUL, UL, CE, C-tick, CCC, KC, CB, PCT
5° ~ 35°C
Operation temperature
Dimensions
431.11mm (W) x 344.16mm (D) x 180.57mm (H)
AC Universal 100 – 240V
AC Input
Power consumption
Lamp
Audio speaker
Typical 420W (boost) <0.5watts(Stand By)/
Typical 365W(standard) <0.5watts(Stand By)
370W (Normal) /
330W (Normal) / 280W (Eco)
280W (Eco)
3W x 2
VGA x 2
DisplayPort x 1
DVI-D x 1
S-Video x 1
5 BNC (RGBHV) x 1
Input Terminals
Component x 1
Composite video x 1
HDMI x 1
RCA stereo x 2
Mini-jack stereo x 2
VGA x 1
Output Terminals
PC audio out x 1
RS-232C
RJ45
Screen trigger: DC Jack x 1 (DC12V 200mA output function)
wire remote
Control Terminals
USB (type B) only for service/mouse control
USB (type A) only for power supply; WHDI
3D sync
Kensington lock
Security
— 68 —
D
DLLPP PPrroojjeeccttoorr—
—U
Usseerr’’ss M
Maannuuaall
Projection Distance vs. Projection Size (WUXGA)
Image Height
h
h
O
A

Projection Distance
V-Sync
Projection Distance and Size Table
Standard projection lens: TR: 1.54 ~ 1.93; offset=55%
TELE
WIDE
Distance (m)
1.66
3.33
4.16
8.31
1.66
3.32
6.63
9.95
Diagonal (")
40
80
100
200
50
100
200
300(*)
Image Width (mm)
862
1723
2154
4308
1077
2154
4308
6462
Image Height (mm)
538
1077
1346
2692
673
1346
2692
4039
h (mm)
269
538
673
1346
337
673
1346
2019
O (mm)
296
592
740
1481
370
740
1481
2221
A (mm)
27
54
67
135
34
67
135
202
Note:
(*) Overdrive.
Long throw projection lens: TR: 1.93 ~ 2.9; offset=55%
TELE
WIDE
Distance (m)
2.5
6.25
12.49
18.74
2.08
6.24
12.47
18.71
Diagonal (")
40
100
200
300
50
150
300
450
Image Width (mm)
862
2154
4308
6462
1077
3231
6462
9693
Image Height (mm)
538
1346
2692
4039
673
2019
4039
6058
h (mm)
269
673
1346
2019
337
1010
2020
3029
O (mm)
296
740
1481
2221
370
1111
2222
3332
A (mm)
27
67
135
202
34
101
202
303
– 69 –
DLP Projector—User’s Manual
New Short throw projection lens: TR: 0.778; offset=55%
FIX
Distance (m)
0.67
1.34
1.68
2.51
Diagonal (")
40
80
100
150
Image Width (mm)
862
1723
2154
3231
Image Height (mm)
538
1077
1346
2019
h (mm)
269
538
673
1010
O (mm)
296
592
740
1111
A (mm)
27
54
67
101
Semi Short throw projection lens: TR: 1.1 ~ 1.3; offset=55%
TELE
WIDE
Distance (m)
1.12
2.80
5.60
8.96
1.18
3.55
7.11
9.00
Diagonal (")
40
100
200
320
50
150
300
380
Image Width (mm)
862
2154
4308
6893
1077
3231
6462
8185
Image Height (mm)
538
1346
2692
4308
673
2019
4039
5116
h (mm)
269
673
1346
2154
337
1010
2019
2558
O (mm)
296
740
1481
2369
370
1111
2221
2814
A (mm)
27
67
135
215
34
101
202
256
Super Long throw projection lens: TR: 3 ~ 5; offset=55%
TELE
WIDE
Distance (m)
3.23
10.77
16.15
19.92
3.23
6.46
12.92
20.03
Diagonal (")
30
100
150
185
50
100
200
310
Image Width (mm)
646
2154
3231
3985
1077
2154
4308
6677
Image Height (mm)
404
1346
2019
2490
673
1346
2692
4173
h (mm)
202
673
1010
1245
337
673
1346
2087
O (mm)
222
740
1111
1370
370
740
1481
2295
A (mm)
20
67
101
125
34
67
135
209
offset % = O/(2xh) × 100%
O=A+h
h=(1/2) × (image height)
— 70 —
D
DLLPP PPrroojjeeccttoorr—
—U
Usseerr’’ss M
Maannuuaall
Projection Distance vs. Projection Size (WXGA)
Image Height
h
h
O
A

Projection Distance
V-Sync
Projection Distance and Size Table
Standard projection lens: TR: 1.62 ~ 2.03; offset=55%
TELE
WIDE
Distance (m)
1.75
3.5
4.37
8.74
1.74
3.49
6.98
10.47
Diagonal (")
40
80
100
200
50
100
200
300(*)
Image Width (mm)
862
1723
2154
4308
1077
2154
4308
6462
Image Height (mm)
538
1077
1346
2692
673
1346
2692
4039
h (mm)
269
538
673
1346
337
673
1346
2019
O (mm)
296
592
740
1481
370
740
1481
2221
A (mm)
27
54
67
135
34
67
135
202
Note:
(*) Overdrive.
Long throw projection lens: TR: 2.03 ~ 3.05; offset=55%
TELE
WIDE
Distance (m)
2.63
6.57
13.14
19.71
2.19
6.56
13.12
19.68
Diagonal (")
40
100
200
300
50
150
300
450
Image Width (mm)
862
2154
4308
6462
1077
3231
6462
9693
Image Height (mm)
538
1346
2692
4039
673
2019
4039
6058
h (mm)
269
673
1346
2019
337
1010
2019
3029
O (mm)
296
740
1481
2221
370
1111
2221
3332
A (mm)
27
67
135
202
34
101
202
303
– 71 –
DLP Projector—User’s Manual
New Short throw projection lens: TR: 0.82; offset=55%
FIX
Distance (m)
0.71
1.41
1.77
2.65
Diagonal (")
40
80
100
150
Image Width (mm)
862
1723
2154
3231
Image Height (mm)
538
1077
1346
2019
h (mm)
269
538
673
1010
O (mm)
296
592
740
1111
A (mm)
27
54
67
101
Semi Short throw projection lens: TR: 1.155 ~ 1.365; offset=55%
TELE
WIDE
Distance (m)
1.18
2.94
5.88
8.82
1.24
3.73
7.46
8.96
Diagonal (")
40
100
200
300
50
150
300
360
Image Width (mm)
862
2154
4308
6462
1077
3231
6462
7754
Image Height (mm)
538
1346
2692
4039
673
2019
4039
4846
h (mm)
269
673
1346
2019
337
1010
2019
2423
O (mm)
296
740
1481
2221
370
1111
2221
2665
A (mm)
27
67
135
202
34
101
202
242
Super Long throw projection lens: TR: 3.15 ~ 5.25; offset=55%
TELE
WIDE
Distance (m)
3.39
11.31
16.96
19.22
3.39
6.78
13.57
19.68
Diagonal (")
30
100
150
170
50
100
200
290
Image Width (mm)
646
2154
3231
3662
1077
2154
4308
6246
Image Height (mm)
404
1346
2019
2289
673
1346
2692
3904
h (mm)
202
673
1010
1144
337
673
1346
1952
O (mm)
222
740
1111
1259
370
740
1481
2147
A (mm)
20
67
101
114
34
67
135
195
offset % = O/(2xh) × 100%
O=A+h
h=(1/2) × (image height)
— 72 —
D
DLLPP PPrroojjeeccttoorr—
—U
Usseerr’’ss M
Maannuuaall
Projection Distance vs. Projection Size (XGA)
Image Height
h
h
O
A

Projection Distance
V-Sync
Projection Distance and Size Table
Standard projection lens: TR: 1.6 ~ 2; offset=50%
TELE
WIDE
Distance (m)
1.63
3.25
4.06
8.13
1.63
3.25
6.50
9.75
Diagonal (")
40
80
100
200
50
100
200
300(*)
Image Width (mm)
813
1626
2032
4064
1016
2032
4064
6096
Image Height (mm)
610
1219
1524
3048
762
1524
3048
4572
h (mm)
305
610
762
1524
381
762
1524
2286
O (mm)
305
610
762
1524
381
762
1524
2286
A (mm)
0
0
0
0
0
0
0
0
Note:
(*) Overdrive.
Long throw projection lens: TR: 2~ 3; offset=50%
TELE
WIDE
Distance (m)
2.44
6.10
12.19
18.29
2.03
6.10
12.19
18.29
Diagonal (")
40
100
200
300
50
150
300
450
Image Width (mm)
813
2032
4064
6096
1016
3048
6096
9144
Image Height (mm)
610
1524
3048
4572
762
2286
4572
6858
h (mm)
305
762
1524
2286
381
1143
2286
3429
O (mm)
305
762
1524
2286
381
1143
2286
3429
A (mm)
0
0
0
0
0
0
0
0
– 73 –
DLP Projector—User’s Manual
New Short throw projection lens: TR: 0.81; offset=50%
FIX
Distance (m)
0.66
1.32
1.65
2.47
Diagonal (")
40
80
100
150
Image Width (mm)
813
1626
2032
3048
Image Height (mm)
610
1219
1524
2286
h (mm)
305
610
762
1143
O (mm)
305
610
762
1143
A (mm)
0
0
0
0
Semi Short throw projection lens: TR: 1.14 ~ 1.34; offset=50%
TELE
WIDE
Distance (m)
1.09
2.72
5.45
8.99
1.16
3.47
6.95
9.03
Diagonal (")
40
100
200
330
50
150
300
390
Image Width (mm)
813
2032
4064
6706
1016
3048
6096
7925
Image Height (mm)
610
1524
3048
5029
762
2286
4572
5944
h (mm)
305
762
1524
2515
381
1143
2286
2972
O (mm)
305
762
1524
2515
381
1143
2286
2972
A (mm)
0
0
0
0
0
0
0
0
Super Long throw projection lens: TR: 3.11 ~ 5.18; offset=50%
TELE
WIDE
Distance (m)
3.16
10.53
15.79
20.00
3.16
6.32
12.64
19.91
Diagonal (")
30
100
150
190
50
100
200
315
Image Width (mm)
610
2032
3048
3861
1016
2032
4064
6401
Image Height (mm)
457
1524
2286
2896
762
1524
3048
4801
h (mm)
229
762
1143
1448
381
762
1524
2400
O (mm)
229
762
1143
1448
381
762
1524
2400
A (mm)
0
0
0
0
0
0
0
0
offset % = O/(2xh) × 100%
O=A+h
h=(1/2) × (image height)
— 74 —
D
DLLPP PPrroojjeeccttoorr—
—U
Usseerr’’ss M
Maannuuaall
h
h
Image Height
Projection Distance vs. Projection Size (1080P)
O
A

Projection Distance
V-Sync
Projection Distance and Size Table
Standard projection lens: TR: 1.54 ~ 1.93; offset=60%
TELE
WIDE
Distance (m)
1.71
3.42
4.27
8.55
1.70
3.41
6.82
10.23
Diagonal (")
40
80
100
200
50
100
200
300(*)
Image Width (mm)
886
1771
2214
4428
1107
2214
4428
6641
Image Height (mm)
498
996
1245
2491
623
1245
2491
3736
h (mm)
249
498
623
1245
311
623
1245
1868
O (mm)
299
598
747
1494
374
747
1494
2241
A (mm)
50
100
125
249
62
125
249
374
Note:
(*) Overdrive.
Long throw projection lens: TR: 1.93 ~ 2.9; offset=60%
TELE
WIDE
Distance (m)
2.57
6.42
12.84
19.26
2.14
6.41
12.82
19.23
Diagonal (")
40
100
200
300
50
150
300
450
Image Width (mm)
886
2214
4428
6641
1107
3321
6641
9962
Image Height (mm)
498
1245
2491
3736
623
1868
3736
5604
h (mm)
249
623
1245
1868
311
934
1868
2802
O (mm)
299
747
1494
2241
374
1121
2241
3362
A (mm)
50
125
249
374
62
187
374
560
– 75 –
DLP Projector—User’s Manual
New Short throw projection lens: TR: 0.778; offset=60%
TELE
Distance (m)
0.69
1.38
1.72
2.58
Diagonal (")
40
80
100
150
Image Width (mm)
886
1771
2214
3321
Image Height (mm)
498
996
1245
1868
h (mm)
249
498
623
934
O (mm)
299
598
747
1121
A (mm)
50
100
125
187
Semi Short throw projection lens: TR: 1.1 ~ 1.3; offset=60%
TELE
WIDE
Distance (m)
1.15
2.88
5.76
8.92
1.22
3.65
7.31
9.01
Diagonal (")
40
100
200
310
50
150
300
370
Image Width (mm)
886
2214
4428
6863
1107
3321
6641
8191
Image Height (mm)
498
1245
2491
3860
623
1868
3736
4607
h (mm)
249
623
1245
1930
311
934
1868
2304
O (mm)
299
747
1494
2316
374
1121
2241
2764
A (mm)
50
125
249
386
62
187
374
461
Super Long throw projection lens: TR: 3 ~ 5; offset=60%
TELE
WIDE
Distance (m)
3.32
11.07
16.60
19.92
3.32
6.64
13.28
19.92
Diagonal (")
30
100
150
180
50
100
200
300
Image Width (mm)
664
2214
3321
3985
1107
2214
4428
6641
Image Height (mm)
374
1245
1868
2241
623
1245
2491
3736
h (mm)
187
623
934
1121
311
623
1245
1868
O (mm)
224
747
1121
1345
374
747
1494
2241
A (mm)
37
125
187
224
62
125
249
374
offset % = O/(2xh) × 100%
O=A+h
h=(1/2) × (image height)
— 76 —
D
DLLPP PPrroojjeeccttoorr—
—U
Usseerr’’ss M
Maannuuaall
Timing Mode Table
Signal
Resolution
NTSC
PAL/SECAM
-
-
640 x 400
720 x 400
720 x 400
640 x 480
640 x 480
640 x 480
640 x 480
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
1024 x 576
1024 x 600
1024 x 600
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1152 x 864
1280 x 720
1280 x 720
1280 x 768
1280 x 768
1280 x 800
1280 x 800
1280 x 800
1280 x 800
1280 x 1024
1280 x 1024
1280 x 1024
1280 x 960
1280 x 960
1360 x 768
1400 x 1050
1440 x 900
1440 x 900
1440 x 900
1600 x1200
VESA
H-Sync V-Sync Composite
RGB
DP/DVI
Component
(KHz)
(Hz)
S-Video
(Analog) HDMI (Digital)
15.7
15.6
37.9
31.5
37.9
31.5
37.9
37.5
43.3
35.2
37.9
46.9
48.1
53.7
76.3
35.8
37.3
41.5
48.4
56.5
60.0
68.7
97.6
99.0
67.5
45.0
90.0
47.4
47.8
49.7
62.8
71.6
101.6
64.0
80.0
91.1
60.0
85.9
47.7
65.3
55.5
55.9
70.6
75.0
○
○
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
60.0
50.0
85.1
70.1
85.0
60.0
72.8
75.0
85.0
56.3
60.3
75.0
72.2
85.1
120.0
60.0
60.0
65.0
60.0
70.1
75.0
85.0
120.0
120.0
75.0
60.0
120.0
60.0
59.9
59.8
74.9
84.9
119.9
60.0
75.0
85.0
60.0
85.0
60.0
60.0
59.9
59.9
75.0
60.0
– 77 –
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
-
-
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
DLP Projector—User’s Manual
Signal
Apple
Macintosh
SDTV
EDTV
HDTV
Resolution
H-Sync V-Sync Composite
RGB
DP/DVI
Component
(KHz)
(Hz)
S-Video
(Analog) HDMI (Digital)
1680 x 1050
1680 x 1050
1920 x 1200
1920 x 1080
640 x 480
832 x 624
1024 x 768
1152 x 870
480i
576i
576p
480p
720p
720p
1080i
1080i
1080p
1080p
1080p
1080p
1080p
64.7
65.3
74.0
67.5
35.0
49.7
60.2
68.7
15.7
15.6
31.3
31.5
37.5
45.0
33.8
28.1
27.0
28.0
33.7
56.3
67.5
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
59.9
60.0
60.0
60.0
66.7
74.5
74.9
75.1
60.0
50.0
50.0
60.0
50.0
60.0
60.0
50.0
24.0
25.0
30.0
50.0
60.0
-
-
-
-
-
-
-
-
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
-
-
-
-
-
-
-
-
-
-
-
-
-
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
O: Frequency supported
—: Frequency not supported
Resolution others than native resolution may be display with uneven size of text or line.
★ The color of
mean Displayable only. (4:3 only)
★ The color of
mean may have a little noise is acceptable, Because video mode sync don’t
auto adjustment.
★ HDTV timing main check tool is DVD player, VG828 is secondary.
— 78 —
D
DLLPP PPrroojjeeccttoorr—
—U
Usseerr’’ss M
Maannuuaall
Projector Dimensions
– 79 –
DLP Projector—User’s Manual
REGULATORY COMPLIANCE
FCC Warning
This equipment has been tested and found to comply with the limits for a Class B digital device
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his/her own
expense.
Changes or modifications not expressly approved by the parties responsible for compliance could
void the user’s authority to operate the equipment.
Canada
This class B digital apparatus complies with Canadian ICES-003.
Safety Certifications
FCC-B, cUL, UL, CE, C-tick, CCC, KC, CB, PCT
— 80 —
D
DLLPP PPrroojjeeccttoorr—
—U
Usseerr’’ss M
Maannuuaall
APPENDIX I
RS-232C Protocol
RS232 Setting
Baud rate:
9600
Parity check:
None
Data bit:
8
Stop bit:
1
Flow Control
None
Control Command Structure
Header code
HEX
ASCII
‘V’
Command code
Data code
End code
Command
Data
0Dh
Command
Data
CR
Operation Command
Note:
XX=00-98, projector's ID, XX=99 is for all projectors
Return Result P=Pass / F=Fail
n: 0:Disable/1: Enable/Vaule(0~9999)
Command Group 00
ASCII
HEX
Function
Description
Return Result
VXXS0001
56h Xh Xh 53h 30h 30h 30h 31h 0Dh
Power On
P/F
VXXS0002
56h Xh Xh 53h 30h 30h 30h 32h 0Dh
Power Off
P/F
VXXS0003
56h Xh Xh 53h 30h 30h 30h 33h 0Dh
Resync
P/F
VXXG0004
56h Xh Xh 47h 30h 30h 30h 34h 0Dh
Get Lamp Hours
Pn/F
VXXS0006
56h Xh Xh 53h 30h 30h 30h 36h 0Dh
System Reset
P/F
VXXG0007
56h Xh Xh 47h 30h 30h 30h 37h 0Dh
0:Reset
1:Standby
Get System Status
2:Operation
3:Cooling
Pn/F
VXXG0008
56h Xh Xh 47h 30h 30h 30h 38h 0Dh
Get F/W Version
Pn/F
– 81 –
DLP Projector—User’s Manual
Command Group 01
ASCII
VXXG0101
HEX
Function
56h Xh Xh 47h 30h 31h 30h 31h 0Dh
Description
Return Value
Get Brightness
n=0~100
Pn/F
VXXS0101n 56h Xh Xh 53h 30h 31h 30h 31h nh 0Dh
Set Brightness
n=0~100
P/F
VXXG0102
Get Contrast
n=0~100
Pn/F
VXXS0102n 56h Xh Xh 53h 30h 31h 30h 32h nh 0Dh
Set Contrast
n=0~100
P/F
VXXG0103
Get Color
n=0~100
Pn/F
VXXS0103n 56h Xh Xh 53h 30h 31h 30h 33h nh 0Dh
Set Color
n=0~100
P/F
VXXG0104
Get Tint
n=0~100
Pn/F
VXXS0104n 56h Xh Xh 53h 30h 31h 30h 34h nh 0Dh
Set Tint
n=0~100
P/F
VXXG0105
Get Sharpness
0~31
Pn/F
VXXS0105n 56h Xh Xh 53h 30h 31h 30h 35h nh 0Dh
Set Sharpness
0~31
P/F
VXXG0106
Get Color
Temperature
0:Warm
1:Normal
2:Cold
Pn/F
Set Color
Temperature
0:Warm
1:Normal
2:Cold
P/F
56h Xh Xh 47h 30h 31h 30h 32h 0Dh
56h Xh Xh 47h 30h 31h 30h 33h 0Dh
56h Xh Xh 47h 30h 31h 30h 34h 0Dh
56h Xh Xh 47h 30h 31h 30h 35h 0Dh
56h Xh Xh 47h 30h 31h 30h 36h 0Dh
VXXS0106n 56h Xh Xh 53h 30h 31h 30h 36h nh 0Dh
VXXG0107
56h Xh Xh 47h 30h 31h 30h 37h 0Dh
VXXS0107n 56h Xh Xh 53h 30h 31h 30h 37h nh 0Dh
Get Gamma
Set Gamma
0:1.8
1:2.0
2:2.2
3:2.4
4:B&W
5:Linear
0:1.8
1:2.0
2:2.2
3:2.4
4:B&W
5:Linear
Pn/F
P/F
Command Group 02
ASCII
HEX
Function
Description
Return Value
VXXS0201
56h Xh Xh 53h 30h 32h 30h 31h 0Dh
Select RGB
P/F
VXXS0202
56h Xh Xh 53h 30h 32h 30h 32h 0Dh
Select RGB2
P/F
VXXS0203
56h Xh Xh 53h 30h 32h 30h 33h 0Dh
Select DVI
P/F
VXXS0204
56h Xh Xh 53h 30h 32h 30h 34h 0Dh
Select Video
P/F
VXXS0205
56h Xh Xh 53h 30h 32h 30h 35h 0Dh
Select S-Video
P/F
VXXS0206
56h Xh Xh 53h 30h 32h 30h 36h 0Dh
Select HDMI
P/F
VXXS0207
56h Xh Xh 53h 30h 32h 30h 37h 0Dh
Select BNC
P/F
VXXS0208
56h Xh Xh 53h 30h 32h 30h 38h 0Dh
Select
Component
P/F
— 82 —
D
DLLPP PPrroojjeeccttoorr—
—U
Usseerr’’ss M
Maannuuaall
Command Group 02
ASCII
HEX
Function
Description
Return Value
VXXS0209
56h Xh Xh 53h 30h 32h 30h 39h 0Dh
Select HDMI 2
(MEDIA)
P/F
VXXS0210
56h Xh Xh 53h 30h 32h 31h 30h 0Dh
Select
Display Port
P/F
VXXS0211
56h Xh Xh 53h 30h 32h 31h 31h 0Dh
Select Multi Media
P/F
VXXG0220
56h Xh Xh 47h 30h 32h 32h 30h 0Dh
Get Current
Source
Return
1:RGB
2:RGB2
3:DVI
4:Video
5:S-Video
Pn/F
6:HDMI 1
7:BNC
8:Component
9:HDMI 2
10:Display Port
11:Multi Media.
Command Group 03
ASCII
VXXG0301
HEX
Function
56h Xh Xh 47h 30h 33h 30h 31h 0Dh
Get Scaling
Description
0:Fill
1:4:3
2:16:9
3:Letter Box
4:Native
5:2.35:1
0:Fill
1:4:3
2:16:9
3:Letter Box
4:Native
5:2.35:1
Return Value
Pn/F
VXXS0301n 56h Xh Xh 53h 30h 33h 30h 31h nh 0Dh
Set Scaling
VXXG0302
Blank
Pn/F
VXXS0302n 56h Xh Xh 53h 30h 33h 30h 32h nh 0Dh
Blank
P/F
VXXG0303
Auto Keystone On
Pn/F
VXXS0303n 56h Xh Xh 53h 30h 33h 30h 33h nh 0Dh
Auto Keystone On
P/F
VXXG0304
Freeze On
Pn/F
VXXS0304n 56h Xh Xh 53h 30h 33h 30h 34h nh 0Dh
Freeze On
P/F
VXXG0305
Volume
n=0~10
Pn/F
VXXS0305n 56h Xh Xh 53h 30h 33h 30h 35h nh 0Dh
Volume
n=0~10
P/F
VXXG0306
Treble
n=0~16
Pn/F
VXXS0306n 56h Xh Xh 53h 30h 33h 30h 36h nh 0Dh
Treble
n=0~16
P/F
VXXG0307
Bass
n=0~16
Pn/F
Bass
n=0~16
P/F
Projection Mode
0:Front
1:Rear
Pn/F
2:Ceiling
3:Rear+Ceiling
56h Xh Xh 47h 30h 33h 30h 32h 0Dh
56h Xh Xh 47h 30h 33h 30h 33h 0Dh
56h Xh Xh 47h 30h 33h 30h 34h 0Dh
56h Xh Xh 47h 30h 33h 30h 35h 0Dh
56h Xh Xh 47h 30h 33h 30h 36h 0Dh
56h Xh Xh 47h 30h 33h 30h 37h 0Dh
VXXS0307n 56h Xh Xh 53h 30h 33h 30h 37h nh 0Dh
VXXG0308
56h Xh Xh 47h 30h 33h 30h 38h 0Dh
– 83 –
P/F
DLP Projector—User’s Manual
Command Group 03
ASCII
HEX
Function
VXXS0308n 56h Xh Xh 53h 30h 33h 30h 38h nh 0Dh
VXXG0309
56h Xh Xh 47h 30h 33h 30h 39h 0Dh
Projection Mode
Set vertical
keystone value
Set vertical
keystone value
Description
Return Value
0:Front
1:Rear
P/F
2:Ceiling
3:Rear+Ceiling
n=-40~+40
Pn/F
n=-40~+40
P/F
Set horizontal
keystone value
n=-20~+20
Pn/F
VXXS0310n 56h Xh Xh 53h 30h 33h 31h 30h nh 0Dh
Set horizontal
keystone value
n=-20~+20
P/F
VXXG0311
Adjust the zoom
n=-10~+10
Pn/F
VXXS0311n 56h Xh Xh 53h 30h 33h 31h 31h nh 0Dh
Adjust the zoom
n=-10~+10
P/F
VXXG0312
Adjust the focus
n=-20~+20
Pn/F
VXXS0312n 56h Xh Xh 53h 30h 33h 31h 32h nh 0Dh
Adjust the focus
n=-20~+20
P/F
VXXG0313
Adjust the vertical
n=-20~+20
lens shift
Pn/F
VXXS0313n 56h Xh Xh 53h 30h 33h 31h 33h nh 0Dh
Adjust the vertical
n=-20~+20
lens shift
P/F
VXXG0314
Adjust the
n=-20~+20
horizontal lens shift
Pn/F
VXXS0309n 56h Xh Xh 53h 30h 33h 30h 39h nh 0Dh
VXXG0310
56h Xh Xh 47h 30h 33h 31h 30h 0Dh
56h Xh Xh 47h 30h 33h 31h 31h 0Dh
56h Xh Xh 47h 30h 33h 31h 32h 0Dh
56h Xh Xh 47h 30h 33h 31h 33h 0Dh
56h Xh Xh 47h 30h 33h 31h 34h 0Dh
VXXS0314n 56h Xh Xh 53h 30h 33h 31h 34h nh 0Dh
VXXG0315
56h Xh Xh 47h 30h 33h 31h 35h 0Dh
VXXS0315n 56h Xh Xh 53h 30h 33h 31h 35h nh 0Dh
VXXG0316
56h Xh Xh 47h 30h 33h 31h 36h 0Dh
VXXS0316n 56h Xh Xh 53h 30h 33h 31h 36h nh 0Dh
VXXG0317
56h Xh Xh 47h 30h 33h 31h 37h 0Dh
VXXS0317n 56h Xh Xh 53h 30h 33h 31h 37h nh 0Dh
VXXG0318
56h Xh Xh 47h 30h 33h 31h 38h 0Dh
VXXS0318
56h Xh Xh 53h 30h 33h 31h 38h nh 0Dh
— 84 —
Adjust the
n=-20~+20
horizontal lens shift
0:Off
3D
1:DLP-Link
2:IR
0:Off
3D
1:DLP-Link
2:IR
0:Off
3D Sync Invert
1:On
0:Off
3D Sync Invert
1:On
0:Frame
Sequential
1:Top/Bottom
3D Format
2:Side-By-Side
3:Frame
Packing
0:Frame
Sequential
1:Top/Bottom
3D Format
2:Side-By-Side
3:Frame
Packing
0:Off
Tilt Angle Warning
1:On
Tilt Angle Warning
0:Off
1:On
P/F
Pn/F
P/F
Pn/F
P/F
Pn/F
P/F
Pn/F
P/F
D
DLLPP PPrroojjeeccttoorr—
—U
Usseerr’’ss M
Maannuuaall
Command Group 04 (Remote Control)
ASCII
HEX
Function
Description
Return Value
VXXS0401
56h Xh Xh 53h 30h 34h 30h 31h 0Dh
UP arrow
P/F
VXXS0402
56h Xh Xh 53h 30h 34h 30h 32h 0Dh
DOWN arrow
P/F
VXXS0403
56h Xh Xh 53h 30h 34h 30h 33h 0Dh
LEFT arrow
P/F
VXXS0404
56h Xh Xh 53h 30h 34h 30h 34h 0Dh
RIGHT arrow
P/F
VXXS0405
56h Xh Xh 53h 30h 34h 30h 35h 0Dh
POWER
P/F
VXXS0406
56h Xh Xh 53h 30h 34h 30h 36h 0Dh
EXIT
P/F
VXXS0407
56h Xh Xh 53h 30h 34h 30h 37h 0Dh
INPUT
P/F
VXXS0408
56h Xh Xh 53h 30h 34h 30h 38h 0Dh
AUTO
P/F
VXXS0409
56h Xh Xh 53h 30h 34h 30h 39h 0Dh
KEYSTONE+
P/F
VXXS0410
56h Xh Xh 53h 30h 34h 31h 30h 0Dh
KEYSTONE-
P/F
VXXS0411
56h Xh Xh 53h 30h 34h 31h 31h 0Dh
MENU
P/F
VXXS0412
56h Xh Xh 53h 30h 34h 31h 32h 0Dh
STATUS
P/F
VXXS0413
56h Xh Xh 53h 30h 34h 31h 33h 0Dh
MUTE
P/F
VXXS0414
56h Xh Xh 53h 30h 34h 31h 34h 0Dh
ZOOM+
P/F
VXXS0415
56h Xh Xh 53h 30h 34h 31h 35h 0Dh
ZOOM-
P/F
VXXS0416
56h Xh Xh 53h 30h 34h 31h 36h 0Dh
BLANK
P/F
VXXS0417
56h Xh Xh 53h 30h 34h 31h 37h 0Dh
FREEZE
P/F
VXXS0418
56h Xh Xh 53h 30h 34h 31h 38h 0Dh
VOLUME+
P/F
VXXS0419
56h Xh Xh 53h 30h 34h 31h 39h 0Dh
VOLUME-
P/F
VXXS0420
56h Xh Xh 53h 30h 34h 32h 30h 0Dh
Enter
P/F
– 85 –
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement