AMX NMX-ENC-N3121 Encoder svsi n3000 series h.264 / wan Direct Control API

AMX NMX-ENC-N3121 Encoder svsi n3000 series h.264 / wan Direct Control API
N-Series N3000
Direct Control API
An N-Series system is comprised of Encoders, Decoders, and other available accessories including Network Video
Recording (NVR) solutions, Window Processing (WP) units, and Audio Transceivers (ATRs). The system allows you to
distribute HD video and audio across a Gigabit Ethernet network. The Encoders accept HDMI sources including
DVI-D, VGA, and Component through the use of passive adapters and analog audio using a balanced or unbalanced
Phoenix connection. The Decoders have HDMI video output ports and will support digital audio (with HDMI-to-DVI
cable or adapter). Options for Power over Ethernet (PoE), analog audio, and more depend on the version of Decoder
used. Please verify hardware capabilities needed prior to ordering.
Legacy hardware and N3000 Series hardware is backwards-compatible (which allows both legacy and N3000 Series
products to be used within the same system as needed).
Each device is controllable via TCP/IP direct socket using device IP addresses and port 50002. Port 50002 supports
a single connection at one time and rejects all other connection attempts until the established connection is closed.
Refer to this document to find the commands needed for your application. Commands are case-sensitive. This
document applies to the N3000 Series of Encoders and Decoders.
NOTE: This information is considered current as of the date of publication. AMX reserves the right to add/modify/
remove commands and change the standard response packet as needed.
NOTE: In the Example sections of this document, <CR> indicates a carriage return as defined by your control method
(e.g., \x0d, $0d, 00x0d, 0x0d, 0dH). <CRLF> is also supported, but not required.
Using the Onboard RS232 Port
Serial communications are enabled on port 50004. If a persistent socket is maintained, this becomes a bidirectional serial port to control the attached source or display. There are no commands to send a serial string.
Instead, simply send the manufacturer’s serial string to port 50004. Any response returns via port 50004 as well.
To set the serial port settings, use N-Able (a free device management software) or a product from the N-Command
series of N-Series Control systems. Similarly to port 50002, this port only supports a single socket connection and
rejects all other connection attempts until the open connection is successfully closed.
Getting More Information
To find direct control commands for other devices (other than N3000 Encoders and Decoders) and for more
information on controlling an N-Series device using N-Able or N-Command, please refer to additional documentation
found on our website (http://www.amx.com/techcenter/manuals.asp).
N3000 Direct Control API
1
Decoders
Decoders
Device Status
Command
Description
Response
Example
Notes
getStatus
Returns with current
status of device.
Current status getStatus<CR>
of device
or
?<CR>
Refer to the return packet
information in the Decoder
Response table on page 4.
getNetStatus
Returns with current
network status of device.
Current status getNetStatus<CR>
of device
Refer to return packet
information in the Decoder
getNetStatus Response
table on page 6.
Description
Response
Notes
Video/Audio Switch
Command
Example
setSettings:decoderMode Specifies AVI stream type
(URL or N-Series
Encoder).
Current status setSettings:decoderMode:URL<CR>
of device
or
setSettings:decoderMode:SVSIEncoder
<CR>
If using the N-Able matrix,
set to SVSIEncoder. If
using a third-party stream
that is specified by a URL,
set to URL.
setSettings:streamURL
Specifies the URL of the
third-party stream.
Current status setSettings:streamURL:
of device
rtp://234.1.0.102:5500<CR>
Only applies when
decoderMode (above) is
set to URL.
set
Switches video streams.
Current status set:1<CR>
of device
If Decoder is set to Audio
Follows Video this will also
switch the audio stream. If
set to a non-existent
stream (like stream 0) then
Decoder will revert to local
play content.
Only applies when
decoderMode (above) is
set to SVSIEncoder.
seta
Switches audio streams.
Current status seta:1<CR>
of device
Command
Description
Response
mute
Disables audio output.
Current status mute<CR>
of device
unmute
Enables audio output.
Current status unmute<CR>
of device
lovol
Changes audio output
level.
Current status lovol:50<CR>
of device
Range in Percentage 0 100%
lovolleft
Changes audio output
level left channel.
Current status lovolleft:50<CR>
of device
Range in Percentage 0 100%
lovolright
Changes audio output
level right channel.
Current status lovolright:50<CR>
of device
Range in Percentage 0 100%
Audio Controls
N3000 Direct Control API
Example
Notes
This affects both analog
outputs (if available) and
digital outputs.
2
Decoders
Mode Change
Command
Description
Response
Example
Notes
live
Changes mode to live play.
Current status of device
live<CR>
Only needed if Decoder has been
commanded to local play.
local
Changes mode to local play.
Current status of device
local:4<CR>
8 playlists available, values: 1 - 8
dviOff
Disables video output.
Current status of device
dviOff<CR>
dviOn
Enables video output.
Current status of device
dviOn<CR>
On by default. Only needed if DVI
port has already been disabled.
Command
Description
Response
Example
Notes
scalerenable
Enables scaled output.
Current status of device
scalerenable<CR>
Enables scaler to selected output
resolution.
scalerdisable
Disables scaled output.
Current status of device
scalerdisable<CR>
Disables scaler. Video output is
source resolution.
modeset
Changes output resolution.
Current status of device
modeset:1080p60<CR> Modes = auto | 1080p59.94 |
1080p60 | 480p | 480p59.94 |
720p59.94 | 720p60
Note: auto = scale to display
native resolution
Scaler Controls
External Device Control
Command
Description
Response
Example
Notes
sendir
Activates a stored IR
command
on Decoder.
Current status of device
sendir:commandname
<CR>
Command name is name created
during commissioning project.
If command is saved as PON then command would be:
sendir:PON.
sendirraw:
<commanddata>
Sends IR command with
Pronto Code.
Current status of device
sendirraw: 0000 006C
0022 0000 015B 00AD
0016 0016 0016 0016
0016 0041 0016 0016
0016 0016 0016 0016
0016 0016 0016 0041
0016 0041 0016 0016
0016 0016 0016 0041
0016 0041 0016
0041 0016 0041 0016
0016 0016 0041 0016
0041 0016 0041 0016
0016 0016 0016 0016
0016 0016 0016 0016
0016 0016 0016 0016
0016 0016 0016 0016
0041 0016 0041 0016
0041 0016 0041 0016
0041 0016 0622<CR>
Sends Pronto Hex Code to
attached IR port. No need to prestore command in device.
sendser:
<commandname>
Executes serial command
stored in unit’s software.
Recall is by saved name.
Current status of device
sendser:play<CR>
The <commandname> is case
and space sensitive. We
recommend saving the
commands as lowercase, all one
word (for example, playpause).
N3000 Direct Control API
3
Decoders
External Device Control (Cont.)
Command
Description
Response
Example
Notes
serSet
Configures serial port to
desired
settings.
Current status of device
serSet:9600,8,none,1
<CR>
serSet:baudrate,databits,parity,st
op. Reference N-Able or other
control software for valid
settings. Only needed if serial
port has not been initialized with
N-Command software.
Decoder Response
Response
Description
Notes
The response packet detailed in this table is sent as a confirmation to all commands as well as in response to the getStatus command.
Additional information may be contained before the response packet. It is recommended when decoding response data to search for the field
required and then output the data accordingly. All fields are separated by "\r".
SVSI_RXGEN2:N322A0400
00463
Device type and serial number
NAME:Adam 3K
Name of device
MAC:00:19:0B:00:0D:BE
Mac address of device
IP:169.254.34.55
IP address of device
NM:255.255.0.0
Subnet mask of device
GW:169.254.1.1
Gateway of device
IPTRIAL:0
IP in trial mode
N-Series software specific
IPMODE:AUTO IP
IP mode of device
DHCP | Static | Auto IP
SWVER:3/24/2016
Software version running on device
N-Series software specific
WEBVER:1412023780
Web version running on device
N-Series software specific
UPDATE:0
N-Series software specific
N-Series software specific
UPDTRY:0
N-Series software specific
N-Series software specific
UPDFAILED:0
N-Series software specific
N-Series software specific
MEDIAPORT0:on
Multicast traffic control
on = multicast can leave port | off = no multicast can leave port
MEDIAPORT1:off
Multicast traffic control
on = multicast can leave port | off = no multicast can leave port
DIVASEN:0
N-Series software specific
N-Series software specific
DIVASIP:0.0.0.0
N-Series software specific
N-Series software specific
discoveryIP:239.254.12.16
N-Series software specific
N-Series software specific
enableDiscoveryPackets:on
N-Series software specific
N-Series software specific
discoveryIntervalSec:10
N-Series software specific
N-Series software specific
discoveryPort:50019
N-Series software specific
N-Series software specific
BAUD:115200
Serial port’s communication speed in bits
per second
300 |1200 | 2400 | 4800 | 9600 | 14400 | 19200 | 28800 | 38400 |
57600 | 115200 | 230400
SNUMB:8
Number of databits per character specified 7 | 8
for the serial port
SPAR:none
Serial port parity setting
even | odd | none
SP2S:1
Serial port’s stop bit setting
1|2
MODE:720p60.mode
Scaler output mode
All modes are followed by .mode. Modes = auto | 1080p59.94
| 1080p60 | 480p | 480p59.94 | 720p59.94 | 720p60
N3000 Direct Control API
Serial string with name (255 character max)
4
Decoders
Decoder Response (Cont.)
Response
Description
Notes
PORTSD1:no
P1 disabled completely
yes = deactivated (no traffic) | no = active and working
GARP:0
Gratuitous ARP option enabled/disabled
N-Series software specific
GARPINT:50
Interval setting
N-Series software specific
UNSOLST:1
Unsolicited status (to N-Series controllers) N-Series software specific
UNSOLSTINT:10
Interval setting
N-Series software specific
ID:0
N-Series software specific
N-Series software specific
DVICEVTDLY:1
N-Act connect event delay time in seconds up to 24 hours (measured in seconds)
DVIDEVTDLY:1
N-Act disconnect event delay time in
seconds
up to 24 hours (measured in seconds)
USERMCMODE:off
Customize multicast address?
on = multicast will be customized | off = multicast will NOT be
customized
USERMCIP:0.0.0.0
Custom multicast address
(USERMCMODE must be on)
multicast address
LPDISKSPACE:83268608
Available disk space for local play storage
N-Series software specific
HTTPS:0
Use secure network connection
0 = off | 1 = on
UNICASTMODE:no
Unicast mode
yes = unicast mode is enabled | no = unicast mode is disabled
LINEOUTVOL_L:35
Current line out volume - left channel
0 - 100%
LINEOUTVOL_R:35
Current line out volume - right channel
0 - 100%
MUTE:0
Mute status
0 = audio enabled | 1 = audio disabled
STREAM:3
Current video stream
Numeric value
STREAMAUDIO:0
Current audio stream
Numeric value | 0 = follow video
ADDLATENCYMILLISEC:0
Amount of additional stream latency
applied
Delay time in milliseconds
SUPPORTBFRAMES:on
Decoder is to expect B-Frames in the
stream
on | off
SCALERBYPASS:no
Scaler status
yes = scaler IS disabled | no = scaler IS enabled
PLAYMODE:local
Current playmode
local | live
PLAYLIST:1
Current local playlist
Number 1 - 8
HDMIAUDIO:on
HDMI audio settings
auto | on | off
LIVEAUDIOLP:off
Play stream audio in local play
on = use stream audio | off = use local play audio
YUVOUT:auto
Color space settings
auto | on = YUV output | off = normal output
SIMDVIDET:on
Simplified DVI detect
on | off
FRAMEHOLD:off
Hold last frame if stream lost
on = hold last frame | off = display local play
VIDOFFNOSTRM:off
Disabled DVI port on loss of stream
on = disable DVI on loss of stream | off= display local play
DVIOFF:off
DVI port state
on = DVI disabled | off = outputting video
N3000 Direct Control API
5
Decoders
Decoder Response (Cont.)
Response
Description
Notes
DVISTATUS:disconnected
DVI status
connected = monitor on/detected | disconnected = monitor off/
detached
INPUTRES:1280x720
Current incoming resolution
XPORTPORT:18888
Network port for the UDP/RTP stream
port number
FPGAVER:8/1/2014
N-Series software specific
N-Series software specific
NEEDVSTRM:0
Not receiving current assigned stream
0 = receiving stream | 1 = not receiving stream
ND_MRRQ:172.20.87.80
Results of N-Able Network Diagnostic
Tools
Tracks potential networking issues. Contact technical support for
more information.
ND_MRRQ_CHG:0
Results of N-Able Network Diagnostic
Tools
Tracks potential networking issues. Contact technical support for
more information.
ND_A_DROP:341
Results of N-Able Network Diagnostic
Tools
Tracks potential networking issues. Contact technical support for
more information.
ND_A_DROP1S:0
Results of N-Able Network Diagnostic
Tools
Tracks potential networking issues. Contact technical support for
more information.
ND_V_DROP:4448
Results of N-Able Network Diagnostic
Tools
Tracks potential networking issues. Contact technical support for
more information.
ND_V_DROP1S:0
Results of N-Able Network Diagnostic
Tools
Tracks potential networking issues. Contact technical support for
more information.
ND_F_DROP:0
Results of N-Able Network Diagnostic
Tools
Tracks potential networking issues. Contact technical support for
more information.
ND_F_DROP1S:0
Results of N-Able Network Diagnostic
Tools
Tracks potential networking issues. Contact technical support for
more information.
FCPC:on
Force copy protection
on | auto
Decoder getNetStatus Response
Response
Description
SVSI_NETSTATS:N3122A20000383
Device type and serial number of the N-Series device
NAME:CBTest2300DEC
User-configured name of the N-Series device
MAC:00:19:0B:80:31:9E
MAC address of the N-Series device
IP:169.254.119.168
IP address of the N-Series device
NM:255.255.0.0
Subnet mask of the N-Series device
GW:169.254.1.1
Gateway IP address of the N-Series device
SWVER:10/24/2016
Software version of the N-Series device
chassisID:mac e0:d1:73:f5:0d:1d
MAC address of the switch connected to the N-Series device
sysName:switchf50d1d
User-configured name of the switch connected to the N-Series device
sysDescr:SG500X-24P 24-Port Gigabit with 4-Port
10-Gigabit PoE Stackable Managed Switch
User-configured description of the switch connected to the N-Series device
portID:ifname gi1/1/5
User-configured name of the switch’s port that is connected to the N-Series device
portDescr:gigabitethernet1/1/5
User-configured description of the switch’s port that is connected to the N-Series device
FPGAVER:0/0/2000
Bit file version of the N-Series device
N3000 Direct Control API
6
Encoders
Encoders
Device Status
Command
Description
Response
Example
Notes
getStatus
Returns with current status
of device.
Current status of device
getStatus<CR>
or
?<CR>
Refer to return packet information
in the Encoder Response table on
page 9.
getNetStatus
Returns with current network Current status of device
status of device.
getNetStatus<CR>
Refer to return packet information
in the Encoder getNetStatus
Response table on page 12.
Command
Description
Response
Example
Notes
mute
Disables audio input.
Current status of device
mute<CR>
This affects both analog inputs and
digital inputs.
unmute
Enables audio input.
Current status of device
unmute<CR>
Command
Description
Response
Example
Notes
live
Changes mode to live play.
Current status of device
live<CR>
Only needed if Encoder has been
commanded to local play.
local
Changes mode to host play.
Current status of device
local:4<CR>
8 playlists available, values: 1 - 8
txdisable
Disables all broadcasts from
Encoder.
Current status of device
txdisable<CR>
Any Encoders currently viewing
stream will transition to local play.
txenable
Enables broadcast from
Encoder.
Current status of device
txenable<CR>
Re-enables broadcasting from
Encoder if previously disabled.
vidsrc
Select the video input on the
Encoder. Hdmivga or
vgahdmi select a preferred
order (digital over analog, or
analog over digital) when
both sources are connected.
Current status of device
vidsrc:hdmionly<CR>
Applies to the N3132 only.
Video input selections = hdmionly |
vgaonly | hdmivga | vgahdmi
Audio Status
Mode Change
USB Record Controls
Command
Description
Example
Notes
formatUSB
Formats the USB drive.
formatUSB<CR>
This command will not work if
there is a recording in
progress.
startRecord
Starts USB record.
startRecord<CR>
Unit must be in SVSI decode
or RTSP mode, or send
multicast must always be
enabled. For HDCP protected
content, the files are
encrypted.
stopRecord
Stops USB record
stopRecord<CR>
If send is configured, the file is
sent to a network file server
after recording stops.
getUSBFree
Returns the free space on
the USB drive (in bytes).
getUSBFree<CR>
setSettings:sendAutoDelete:
[on,off]
If on, file on the USB drive
are automatically deleted
after sending.
setSettings:sendAutoDelete:on<CR>
N3000 Direct Control API
7
Encoders
USB Record Controls (Cont.)
Command
Description
Example
Notes
setSettings:sendConvertMP4:
[on,off]
Converts file to MP4 before
sending.
setSettings:sendConvertMP4:on<CR>
This process takes extra USB
storage and time.
setSettings:sendValidate:[on,off]
Validates that the send
completed before deleting.
setSettings:sendValidate:on<CR>
This process takes extra USB
storage and time.
setSettings:sendPort:port
Sets a network port number
for sending files in ftp or sftp
mode.
setSettings:sendPort:22<CR>
setSettings:sendPath:path
Sets a network storage path
to transfer record files for
Windows share mode.
setSettings:sendPath:fileStore <CR>
setSettings:recordBaseName:name
Sets base filename for
record files.
setSettings:recordBaseName:MyRecord The file number and extension
<CR>
are appended to the base
name.
setSettings:sendDestAddr:addr
setSettings:sendDestAddr:192.168.1.91
Sets a destination address
for sending files via ftp or sftp <CR>
mode.
setSettings:sendUserPassword:
password
File server user password.
setSettings:sendUserPassword:testp14
<CR>
setSettings:sendUserName:name
File server user name.
setSettings:sendUserName:mwerline
<CR>
setSettings:usbEnable:[on,off]
Turns USB port on or off.
setSettings:usbEnable:off <CR>
setSettings:sendSchedule:[ never,
immediate, attime, inwindow]
Sets when to transfer files
after recording stops.
setSettings:sendSchedule:inwindow<CR>
setSettings:sendMethod:[ FTP,
SFTP, SHARE]
Sets the protocol to transfer
files after record stop.
setSettings:sendMethod:FTP<CR>
setSettings:sendStartTime:hour:min
Sets a start of time window
for transferring files (in 24
hour format).
setSettings:sendStartTime:12:30<CR>
setSettings:sendEndTime:hour:min
Sets an end of time window
for transferring files (in 24
hour format).
setSettings:sendEndTime:15:30<CR>
Scaler Controls
Command
Description
Response
Example
Notes
scalerenable
Enables scaled output.
Current status of device
scalerenable<CR>
Enables scaler. Content will be
broadcast as selected output
resolution.
scalerdisable
Disables scaled output.
Current status of device
scalerdisable<CR>
Disables scaler.
modeset
Changes output resolution.
Current status of device
modeset:1080p60<CR
>
Modes = 1080p59.94 | 1080p60 |
480p | 480p59.94 | 720p59.94 |
720p60
N3000 Direct Control API
8
Encoders
External Device Control
Command
Description
Response
Example
Notes
sendirraw:
<commanddata>
Sends IR command with
Pronto Code.
Current status of
device
sendirraw: 0000 006C
0022 0000 015B 00AD
0016 0016 0016 0016
0016 0041 0016 0016
0016 0016 0016 0016
0016 0016 0016 0041
0016 0041 0016 0016
0016 0016 0016 0041
0016 0041 0016
0041 0016 0041 0016
0016 0016 0041 0016
0041 0016 0041 0016
0016 0016 0016 0016
0016 0016 0016 0016
0016 0016 0016 0016
0016 0016 0016 0016
0041 0016 0041 0016
0041 0016 0041 0016
0041 0016 0622<CR>
Sends Pronto Hex Code to
attached IR port. No need to prestore command in device.
sendser:
<commandname>
Executes serial command
stored in unit’s software.
Recall is by saved name.
Current status of
device
sendser:play<CR>
The <commandname> is case and
space sensitive. We recommend
saving the commands as
lowercase, all one word (for
example, playpause).
serSet
Configures serial port to
desired
settings.
Current status of
device
serSet:9600,8,none,1<
CR>
serSet:baudrate,databits,parity,sto
p. Reference N-Able or other
control software for valid settings.
Only needed if serial port has not
been initialized with N-Command
software.
Encoder Response
Response
Description
Notes
The response packet detailed in this table is sent as a confirmation to all commands as well as in response to the getStatus command.
Additional information may be contained before the response packet. It is recommended when decoding response data to search for the field
required and then output the data accordingly. All fields are separated by "\r".
SVSI_TXGEN2:N312A030000006
Device type and serial number
NAME:Adam N-Enc
Device name
MAC:00:19:0B:00:08:86
Device MAC
IP:169.254.119.168
Device IP
NM:255.255.0.0
Device subnet mask
GW:169.254.1.1
Device gateway
IPTRIAL:0
IP trial mode (during resetting of IP
addresses)
N-Series software specific
IPMODE:AUTO IP
IP mode of device
DHCP | Static | Auto IP
SWVER:6/21/2014
Software version
N-Series software specific
WEBVER:1371820321
Web interface version
N-Series software specific
UPDATE:0
Update flags for N-Series updater
N-Series software specific
UPDTRY:0
Update flags for N-Series updater
N-Series software specific
UPDFAILED:0
Update flags for N-Series updater
N-Series software specific
N3000 Direct Control API
9
Encoders
Encoder Response (Cont.)
Response
Description
Notes
MEDIAPORT0:on
P0 multicast status
on = multicast can leave port | off = no multicast can leave
port
MEDIAPORT1:on
P1 multicast status
on = multicast can leave port | off = no multicast can leave
port
DIVASEN:0
N-Series software specific
N-Series software specific
DIVASIP:0.0.0.0
N-Series software specific
N-Series software specific
discoveryIP:239.254.12.16
N-Series software specific
N-Series software specific
enableDiscoveryPackets:on
N-Series software specific
N-Series software specific
discoveryIntervalSec:10
N-Series software specific
N-Series software specific
discoveryPort:50019
N-Series software specific
N-Series software specific
BAUD:9600
Serial port’s communication speed in bits per 300 |1200 | 2400 | 4800 | 9600 | 14400 | 19200 | 28800 |
second
38400 | 57600 | 115200 | 230400
SNUMB:8
Number of databits per character specified
for the serial port
7|8
SPAR:none
Serial port parity setting
even | odd | none
SP2S:1
Serial port’s stop bit setting
1|2
MODE:720p59.94.mode
Scaler output mode
All modes are followed by .mode. Modes = auto |
1080p59.94 |
1080p60 | 480p | 480p59.94 | 720p59.94 | 720p60
PORTSD1:no
P1 disabled completely
yes = deactivated (no traffic) | no = active and working
GARP:0
Gratuitous ARP option enabled/disabled
N-Command specific
GARPINT:50
Interval for ARP
N-Command specific
UNSOLST:1
Unsolicited status enabled
N-Command specific
UNSOLSTINT:10
Interval for unsolicited status
N-Command specific
ID:0
N-Series software specific
N-Series software specific
DVICEVTDLY:1
N-Act connect event delay time in seconds
up to 24 hours (measured in seconds)
DVIDEVTDLY:1
N-Act disconnect event delay time in
seconds
up to 24 hours (measured in seconds)
USERMCMODE:off
Customize multicast address?
on = multicast will be customized | off = multicast will NOT
be customized
USERMCIP:0.0.0.0
Custom multicast address (USERMCMODE
must be on)
multicast address
UNICASTMODE:no
Unicast mode
yes = unicast mode is enabled | no = unicast mode is
disabled
UNICASTADDR:0.0.0.0
Unicast network address for the AV stream
(if unicast mode is enabled)
IP address
LPDISKSPACE:95454208
Host play disk space
N-Series software specific
HTTPS:0
Use secure network connection
0 = off | 1 = on
LINEIN:bal
Line in is balanced or unbalanced
se = unbalanced audio | bal = balanced audio
MUTE:0
Mute status
0 = audio enabled | 1 = muted
STREAM:134
Broadcast stream of Encoder
N3000 Direct Control API
10
Encoders
Encoder Response (Cont.)
Response
Description
SAMPLE:44100
Audio sample rate
AUDIODELAY:21000
Audio delay in milliseconds
N-Series software specific (not currently used)
CLRSPCCOR:auto
Color space correction
auto | on | off
Note: Should be auto.
HPNONSUP:off
Host play in unsupported mode
N-Series software specific
HDMIAUDIO:auto
HDMI audio state
auto | on | off
LIVEAUDIOHP:off
Use live audio source while in HP mode
on | off (N-Series software specific)
STREAMPCMAUDIO:off
Indicates separate N-Series compatible
audio stream transmitted by an Encoder
on | off
QUALITY:100
Compression level
N-Series software specific
MOTQUAL:100
Motion level
N-Series software specific
VIDEOBITRATE:5000000
Bitrate for the compressed video stream
bitrate in bits per second
SCALERBYPASS:yes
Scaler enabled/disabled
yes = disabled | no = enabled
PLAYMODE:live
Device mode
live | local
PLAYLIST:1
Host playlist to be displayed
Playlists are 1 - 8
OUTBW:1034160
Output bandwidth in bytes per second
N-Series software specific
OUTBWMBS: 7.8
Output bandwidth in megabytes per second
N-Series software specific
AUDOUTBW:192000
Current compressed audio bitrate
bitrate in bits per second
AUDOUTBWKBS:192.0
Current compressed audio bitrate
bitrate in kilobits per second
DVIINPUT:connected
Source status
connected = source is available | disconnected = no
source
DVIPASSTHR:disconnected
Passthrough port
connected = monitor detected | disconnected = no
monitor
PTSIMDVIDET:off
Simplified DVI detect for passthrough port
N-Series software specific
PTYUVOUT:auto
Passthrough color correction
auto | on | off
PTHDMIAUDIO:on
Passthrough HDMI audio
on | off
CPC:allowed
Allow HDCP video to be encoded?
allowed | blocked
CISPROT:not-protected
Current source protected?
protected | not-protected
INPUTRES:1280x720
Current incoming resolution
XPORTSTREAM:on
Transport stream encapsulation
on | off
RTPENCAP:off
RTP stream encapsulation
on | off
RTMPURL:rtmp:
URL for RTMP transmission
content server’s URL
RTMPStream:none
RTMP stream name
content server’s stream name
STREAMURL:rtsp://
169.254.151.33:8554/N3000
Network URL for Encoder AV stream
stream URL
AGAINL:0
Volume control - left channel (gain only)
0 - 100%
AGAINR:0
Volume control - right channel (gain only)
0 - 100%
FPGAVER:6/20/2014
N-Series software specific
N-Series software specific
N3000 Direct Control API
Notes
11
Encoders
Encoder Response (Cont.)
Response
Description
Notes
REDBRIGHTNESS:-64
Analog video brightness adjustment
-127 to 127
GREENBRIGHTNESS:-64
Analog video brightness adjustment
-127 to 127
BLUEBRIGHTNESS:-64
Analog video brightness adjustment
-127 to 127
SOGWindow:16
Current sync on green sensitivity
0-63
INPUTGAINLEFT:0
Audio input gain (left channel)
0 | -1.5 | -3 | -4.5 | -6 | -7.5 | -9 | -10.5 | -12 dB
INPUTGAINRIGHT:0
Audio input gain (right channel)
0 | -1.5 | -3 | -4.5 | -6 | -7.5 | -9 | -10.5 | -12 dB
RTSPPORT:8554
RTSP network port number
port number
Encoder getNetStatus Response
Response
Description
SVSI_NETSTATS:N3132A20000383
Device type and serial number of the N-Series device
NAME:CBTest2300ENC
User-configured name of the N-Series device
MAC:00:19:0B:80:31:9E
MAC address of the N-Series device
IP:169.254.119.168
IP address of the N-Series device
NM:255.255.0.0
Subnet mask of the N-Series device
GW:169.254.1.1
Gateway IP address of the N-Series device
SWVER:10/24/2016
Software version of the N-Series device
chassisID:mac e0:d1:73:f5:0d:1d
MAC address of the switch connected to the N-Series device
sysName:switchf50d1d
User-configured name of the switch connected to the N-Series device
sysDescr:SG500X-24P 24-Port Gigabit with 4-Port
10-Gigabit PoE Stackable Managed Switch
User-configured description of the switch connected to the N-Series device
portID:ifname gi1/1/5
User-configured name of the switch’s port that is connected to the N-Series device
portDescr:gigabitethernet1/1/5
User-configured description of the switch’s port that is connected to the N-Series
device
FPGAVER:0/0/2000
Bit file version of the N-Series device
Last Revised: 04/2018
© 2018 Harman. All rights reserved. AMX, AV FOR AN IT WORLD, and HARMAN, and their respective logos are registered trademarks of HARMAN.
Oracle, Java and any other company or brand name referenced may be trademarks/registered trademarks of their respective companies.
AMX does not assume responsibility for errors or omissions. AMX also reserves the right to alter specifications without prior notice at any time.
The AMX Warranty and Return Policy and related documents can be viewed/downloaded at www.amx.com.
3000 RESEARCH DRIVE, RICHARDSON, TX 75082 AMX.com | 800.222.0193 | 469.624.8000 | +1.469.624.7400 | fax 469.624.7153
AMX (UK) LTD, AMX by HARMAN - Unit C, Auster Road, Clifton Moor, York, YO30 4GD United Kingdom • +44 1904-343-100 • www.amx.com/eu/
850DOC3KCMD REV:E
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement