AMX MXT-1900L-PAN-NC modero x series g4 touch panels (no camera, no microphone) Quick Start Guide

AMX MXT-1900L-PAN-NC modero x series g4 touch panels (no camera, no microphone) Quick Start Guide

QUICK START GUIDE

MXT-1900L-PAN

19.4" Modero X

®

Series Panoramic Tabletop Touch Panel

Overview

The MXT-1900L-PAN 19.4" Modero X Series ® Panoramic Tabletop Touch Panel (

FG5968-02

) features a beautiful, panoramic capacitive multi-touch screen that provides users access to multiple applications with minimal navigation. It is hardware-ready for support of Near Field Communication™ (NFC) Technology to allow personalization of the user experience and productivity enhancing capabilities through integration with NFC capable personal devices. The distinctive, low-profile design is engineered to sit perfectly on a table without obstructing views.

Sleep Button NFC Sensor Sleep Button USB Ports (2)

Connector Locations

Two USB ports for peripherals are located on the rear right corner of the device (FIG. 2). Type A USB Ports Sleep button Speaker

FIG. 2

MXT-1900L-REAR VIEW USB peripherals (mouse, keyboard, etc.) may be connected to either of the two USB ports on the rear of the device.

The power and Ethernet connectors, as well as an additional USB port are located on the bottom of the device (FIG. 3). The underside USB port, as well as the two rear USB ports, may be used with a flash drive for page transfers or firmware upgrades. 13.5V Power Port Cable Slot

FIG. 1

MXT-1900L-PAN

Product Specifications

MXT-1900L-PAN SPECIFICATIONS

Dimensions (HWD) Weight Power Consumption • Full-On: 32W ( 13.5V

• Standby: 3.10 W ( 13.5V

, 2.4A) , 0.27A) • Start-Up Inrush Current: 4.0A for 80 μ sec External Power Supply Required Certifications Environmental Requires one of these AMX power sources (not included): • PSR4.4 Power Supply, 4.5A, 3.5 mm Phoenix with Retention Screws (FG423-46) • PSN4.4 Power Supply, 4.5A, 3.5 mm Phoenix, 13.5V

(

discontinued

) (FG423-45) • MXA-MPL Modero X/S Series Multi Preview Live (FG5968-10) • MXA-MP Modero X/S Series Multi Preview (FG5968-20) • FCC Part 15 Class B • C-Tick CISPR 22 Class B • CE EN 55022 Class B and EN 55024 • CB Scheme IEC 60950-1 • IC • IEC/EN-60950 • UL 60950-1 • RoHS/WEEE compliant • Temperature (Operating): 32°F to 104°F (0°C to 40°C) • Temperature (Storage): 4°F to 140°F (-20°C to 60°C) • Humidity (Operating): 20% to 85% RH • Humidity (Storage): 5% to 85% RH • Power ("Heat") Dissipation: On: 119.4 BTU/hr Standby: 23.9 BTU/hr Included Accessories 7" x 20 3/8" x 5 5/16" (177 mm x 519 mm x 135 mm) 9.4 lbs (4.26 Kg) • Locking 2-pin Phoenix mate (41-0002-SA) • MXA-USB-C, USB Port Cover Kit (FG5968-18) • HPG-10-10K, 3/4" Mini-Grommet (FG570-01) • MXA-CLK, Modero X/S Series Cleaning Kit (FG5968-16) Ferrite Type A USB Port

FIG. 3

MXT-1900L-PAN UNDERSIDE CONNECTORS The MXT-1900L-PAN does not have individual channels on the base of the device to allow passage of cables from underneath the base. Instead, it has one slot at the base to allow options on cable configuration, with channels for securing power and Ethernet cables (FIG. 4).

Tie-wrap Tie-wrap channels

FIG. 4

TIE-WRAP FOR POWER CONNECTOR FERRITE Each channel side has slots for attaching tie-wraps to secure each cable. The ferrite on the power cable must be secured with the included tie-wrap during installation to prevent the possibility of the panel not sitting flush on the table. Other cables may be secured with tie-wraps if desired, but this is not necessary.

Wiring Guidelines

The MXT-1900L-PAN uses a 13.5V

connector may damage the device.

-compliant power supply to provide power to the panel via the 2-pin 3.5 mm captive wire PWR connector. The incoming PWR and GND wires from the power supply must be connected to the corresponding locations within the PWR connector.

Note: Apply power to the panel only after installation is complete.

Note: Connecting power to the MXT-1900L-PAN should be done using the included 2-pin 3.5mm captive wire connector included with the device. This connector is retained within its port with locking screws instead of the pins on each side of standard captive wire connectors, and using force to insert a standard captive wire

Wiring a Power Connection

To use the 2-pin 3.5 mm captive wire connector with a 13.5V

sure to insert and tighten the screws before applying power. -compliant power supply, the incoming PWR and GND wires from the external source must be connected to their corresponding locations on the connector (FIG. 5). The connector uses locking screws to insure a connection to the device, so make PWR + GND To the Touch Panel

FIG. 5

NETLINX POWER CONNECTOR WIRING DIAGRAM Power Supply 1.

2.

3.

Insert the PWR and GND wires on the terminal end of the 2-pin 3.5 mm captive wire cable. Match the wiring locations of the +/- on both the power supply and the terminal connector.

Tighten the clamp to secure the two wires. Do not tighten the screws excessively; doing so may strip the threads and damage the connector.

Verify the connection of the 2-pin 3.5 mm captive wire to the external 13.5V

-compliant power supply and apply power.

Powering On/Off X Series Panels

Modero X Series touch panels may be powered on by touching and holding the

Sleep

button. To power off the panel, press and hold the Sleep button, and select

Power Off

on the on-screen menu (FIG. 6):

FIG. 6

SLEEP BUTTON - PRESS AND HOLD TO ACCESS POWER OFF/SETTINGS OPTIONS

Configuration and Programming

X Series touch panels are equipped with a

Settings

menu that provides the ability to configure various features on the panels. To access the

Settings

menu, press and hold the Sleep button, and select

Settings

.

Note: Information on the Settings menu, panel configuration, and programming is provided in the Modero X Series Programming Guide, available at www.amx.com.

Setting the Panel’s Device Number and Device Name

1.

In the Settings menu, select

NetLinx

. This opens a password keypad.

2.

3.

4.

Enter the panel password into the keypad (the default is

1988

) and select

OK

to access the

NetLinx

page.

Press

Device Number

to open the NetLinx editing window.

Enter a unique Device Number assignment for the panel and press

OK

.

5.

Enter a unique Device Name assignment for the panel and press

OK

.

Configuring the Panel’s IP Address

The first step is to configure the panel’s IP address. Note that this only configures the panel to communicate with a network; it is still necessary to connect to the NetLinx Master (see

Connecting to a NetLinx Master

below).

Network Communication via DHCP

1.

In the

Ethernet

page, press

DHCP/Static

field to open the

DHCP/Static

window. Note that

DHCP

is the default setting.

2.

Select

Host Name

, enter the new host name 3.

Network Communication via Static Address

1.

Press In the

OK

to save changes.

Ethernet

page, press

DHCP/Static

to open the

DHCP/Static

window.

2.

3.

4.

Select

Static

to open the

Static IP

window.

Press any field to open a keypad or keyboard (depending on the field), and enter the appropriate network address information.

Press

OK

to save your changes and return to the

Ethernet

page.

Connecting to a NetLinx Master

To establish the type of connection to make between the panel and the NetLinx Master: 1.

In the

NetLinx

page, press

Mode

to choose the connection mode (

URL

,

Listen

or

Auto

):

CONNECTION MODES Mode Description

URL The device connects to the target Master’s IP address via a TCP connection.

Listen This mode allows the panel to “listen” for the Master’s communication signals. Note that in this mode, the

System Number

and

Master IP/URL

fields are read-only.

Auto Use this mode when both the panel and the NetLinx Master are on the same Subnet.

Procedures

1) Select

URL

in the

Mode

menu.

2) Enter the

Master IP/URL

,

Master Port Number

, and

Username

/

Password

(if required by the Master).

3) Press

OK

to save changes.

1) Select 3) Press

Listen OK

in the

Mode

menu.

2) Confirm the panel’s IP address is on the Master’s URL list (via NetLinx Studio).

to save changes.

Note: The Host Name (set on the Ethernet page), can be used to locate the panel on the Master (particularly useful for DHCP connections where the IP address can change).

1) Select 3) Press

Auto OK

in the

Mode

menu.

2) Enter the System Number and Username and Password (if applicable). to save changes.

2.

If password security is enabled on the target Master, enter the Username and Password: a. Select

Username

to open the

NetLinx

window.

b. Enter the

Username

and

Password

required by the Master.

c. Press

Manual.

OK

information.

to save changes and return to the

NetLinx

page.

Related Software and Additional Documentation (at www.amx.com)

• Programming the Modero X Series touch panels requires the use of the latest versions of NetLinx Studio and TPDesign4, both available to download at www.amx.com. Refer to the NetLinx Studio and TPDesign4 online help for • For additional information on the MXT-1900L-PAN panel, refer to the • For detailed information on the Settings menu as well programming information and instructions on upgrading firmware, refer to the

X Series Touch Panels MXD/T-2000XL-PAN & MXD/T-1900L-PAN Instruction Modero X Series Programming Guide

.

• Detailed specifications drawings for the MXD/T-1900L-PAN are available to download from www.amx.com.

Last Revised: 6/22/2015 © 2015 Harman. All rights reserved. Modero X and Modero X Series, AMX, AV FOR AN IT WORLD, and HARMAN, and their respective logos are registered trademarks of HARMAN. Oracle, Java and any other company or brand name referenced may be trademarks/registered trademarks of their respective companies.

AMX does not assume responsibility for errors or omissions. AMX also reserves the right to alter specifications without prior notice at any time.

The AMX Warranty and Return Policy and related documents can be viewed/downloaded at www.amx.com.

3000 RESEARCH DRIVE, RICHARDSON, TX 75082 AMX.com | 800.222.0193 | 469.624.8000 | +1.469.624.7400 | fax 469.624.7153

AMX (UK) LTD, AMX by HARMAN - Auster Road, Clifton Moor, York, YO30 4GD United Kingdom • +44 1904-343-100 • www.amx.com/eu/

93-5968-02 REV: H

Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement