PR LIGHTING XPAR 150 Zoom User Manual

PR LIGHTING XPAR 150 Zoom User Manual
XPar 150 Zoom
PR-8203
The user manual contains important information about the safe installation and use of a projector. Please read
and follow these instructions carefully and keep the manual in a safe place for future reference.
PR LIGHTING LTD.
http://www.pr-lighting.com
INDEX
1. SAFETY AND WARNINGS…………………………………………………………………………………………………… 1
2. INSTUCTIONS ………………………………………………………………………………………………………………… 2
●CLEANING AND MAINTENANCE ………………………………………………………………………………………… 2
●TROUBLESHOOTING………………………………………………………………………………………………………… 2
3. APPEARANCE ………………………………………………………………………………………………………………… 3
4. INSTALLATION ……………………………………………………………………………………………………………… 4
●RIGGING ……………………………………………………………………………………………………………………… 4
●PLACE A UNIT ON A FLAT SURFACE……………………………………………………………………………………… 4
●INSTALLATION OF BARN DOOR…………………………………………………………………………………………… 4
●TRANSPORTATION…………………………………………………………………………………………………………… 5
●POWER CONNECTIONS …………………………………………………………………………………………………… 5
●DMX CONTROL CONNECTION …………………………………………………………………………………………… 6
●DMX TERMINATOR ………………………………………………………………………………………………………… 6
5. SETUP AND CONFIGURATION……………………………………………………………………………………………… 7
●FRONT PANEL OPERATION………………………………………………………………………………………………… 7
●DMX START ADDRESS……………………………………………………………………………………………………… 7
●DMX WIRELSESS CONTROL ……………………………………………………………………………………………… 7
●STAND-ALONE MODE……………………………………………………………………………………………………… 7
●MASTER/SLAVE MODE……………………………………………………………………………………………………… 7
6.OPERATION MENU …………………………………………………………………………………………………………… 8
7. DMX PROTOCOL …………………………………………………………………………………………………………… 9
8.TECHNICAL DATA……………………………………………………………………………………………………………… 11
9.CIRCUIT DIAGRAM AND PCB CONNECTIONS…………………………………………………………………………… 13
●CIRCUIT DIAGRAM ………………………………………………………………………………………………………… 13
●PCB CONNECTIONS………………………………………………………………………………………………………… 14
10.COMPONENT ORDER CODES ……………………………………………………………………………………………… 14
ACCESSORIES
The following items are supplied with the projector and please check:
Name
G clamps
Power cord
XLR connector
Safety cord
User manual
Transparent Cover+ seal+ screws ×6
Barn Door
Frost panel(Barn Door + Frost panel)
Quantity
1
1
1
1
1
1
1
1
Unit
Pc
Pc
Set
Pc
Pc
Set
Set
Set
Remark
With plug and socket
Male and female
Optional
Optional
Optional
Please note that as part of our ongoing commitment to continuous product development, specifications are
subject to change without notice. Whilst every care is taken in the preparation of the manual we reserve the
right to change specifications in the course of product improvement. The publishers cannot be held responsible
for the accuracy of the information herein, or any consequence arising from them.
Every unit is tested completely and packed properly by the manufacturer. Please make sure the packing and /
or the unit are in good condition before installation and use. Should there be any damage caused by
transportation, consult your dealer and do not use the unit. Any damage caused by improper use will not be
assumed by the manufacturer and / or dealer.
1. SAFETY AND WARNINGS
.
NOTE
Before a projector’s installation, power-on, operation and maintenance, please carefully read
the safety information hereinafter!
The following safety signs are used in the user manual.
Warning
User
Manual
Electrical
shock
Goggles
Protective
Gloves
Flames
High
Temperature
● When unpacking , check if there is transportation damage before using the projector. Should there be
any damage caused by transportation, consult your dealer and do not use it.
●The manufacture is not responsible for loss caused by the user not following the manual or changing the
projector as he/she likes
●Please be noted that the damage caused by changing the projector at will is not warranted.
● Do not hesitate to contact the dealer or the manufacturer if any questions or advice.
● Use only in dry locations. Keep this unit away from rain and moisture, excessive heat, humidity and dust. Do not
allow contact with water or any other liquids.
●The projector should be kept away from high temperature, fire, electrical surge, vibration and strong light while
being operated
●The projector is only intended for installation, operation and maintenance by qualified personnel. And the
operation must strictly follow the procedures in the manual
●No repairable parts in the projector and do not open covers for maintenance by yourself.
●Don’t look straightly into the light sources especially for epileptics, otherwise eyes will be burned.
●Do not connect this device to any type of dimmer pack
●After lamp switched on, the minimum distance between the projector and illuminated surface is 10m
●lens and other optical parts shall be replaced immediately if they have deformed or been damaged, otherwise the
light output will be compromised.
●Before operation, please confirm that all covers(housing) are on and screws tightened. It’s forbidden to use a
projector while covers(housing)are off
●Keep the lamp clean and do not touch it with bare hands.
●While operating it, wear protective items.
●Any electrical connection must be carried out by a qualified person .
●Before installation, please confirm the voltage supplied matches what is required for the projector
●Each projector must be properly earthed and installed as per related electrical standards.
●Do not use power cord with its insulator damaged and connect the power cord with other cables.
●If the projector is not used or under cleaning,, please hold the plug and unplug it. Do not unplug it forcefully or
by pulling the power cable.
●All power cords must conform to related safety and regulations
●While being operated, the projector should not be under rains or in humidity.
●Do not switch on and off the projector constantly in very short intervals, otherwise the light source’s and other
electrical parts’ life will be shortened .
●There are safety cord holes at the bottom of the base of a projector. In view of safety, please run the safety cord
supplied through the safety cord holes for safety support.
●Before any installation, maintenance and cleaning work, please ensure the projector is disconnected from power
mains.
-1-
●After running for 5minutes at constant temperature environment, the temperature of the housing of the
projector is 45℃.After stable operation , its temperature is70℃.
●While the lamp is stricken for the first time, there will be smoke and strange smell. It’s normal and does not
mean the projector has some defects.
●While operated, do not touch the metallic housing. It is very hot during operation.
●Do not mount the projector directly on inflammable surface.
●Do not project the beam straightly on combustible items and the minimum distance between the projector
and illuminated items is 10m.
●A projector should be installed with good ventilation and the minimum distance between the projector and
walls is 50cm. At the same time, please ensure the fans and air inlets and outlets are workable.
2. INSTRUCTIONS
●CLEANING AND MAINTENANCE
The accumulation of oil, smoke and dust on the lens will compromise the light output. Cleaning a projector is very necessary to ensure
a reliable use of it. Without the permission by a qualified person for internal part replacement, it is forbidden to dismantle a unit.
Cleaning frequency is to be decided by operations and its environment. Use soft cloth and normal detergent for glass for cleaning work.
It’s advised external optical system be cleaned every 20days. Keep lens clean and do not touch optical parts with bare hands.
●Before any maintenance and cleaning, please ensure the project is off the power
●Only qualified person is allowed to do maintenance
●During maintenance and before maintenance, the projector must be off power.
●To avoid internal damage, sun light or other light mustn’t penetrate into the projector via front lens whether
it runs or not
●Do not use alcohol or other organic solvent to clean the housing to avoid damage.
●Do not use any solvent with chemical elements to clean color filters or hot mirror.
●TROUBLESHOOTING
PROBLEM
The projector doesn’t switch on
The lamp is on but the projector doesn’t respond
to the controller
The projector functions intermittently
Beam appears dim, Low in brightness
The project image appears to have a halo
Heavily Defective Beam
ACTION










Check the fuse on the power socket.
Check the lamp.
Make sure that the fixture’s start address is right
Replace or repair the XLR signal cable.
Make sure the fan is working well or fans and their shields are not blocked
Make sure the lamp is within its lifespan
Remove dust or grease from the lenses.
Carefully clean the lamp, optical lenses and other components.
Check if lens are in good condition(not cracked)
Clean dust or grease on the lens.
-2-
3. APPEARANCE
(The unit has two different settings. One is with wireless control function and the other version without it. After either
version leaves the factory, they can’t be changed in between as you like)
With wireless control function
Without wireless control function
Product’s External Functional Sketch:
No.
Name
Remarks
1
Frost panel(Optional)
Other components should be selected if frost panel selected
2
Barn Door (Optional)
3
Knob
4
Arm
5
Support
6
Safety cord hole
7
XLR cable
Small
8
Power Cord
Big
9
Transparent Display Cover(Optional )
Used in harsh environment like dusty area or being under water
10
Wireless Antenna
Only Supplied with the version with Wireless control function
11
Butterfly screws
Installation and dismantlement of barn door
-3-
4. INSTALLATION
Arm
on flat surface with
antenna facing up
Safety Cord
run through
safety cord hole
Support
hung with antenna
facing down
●RIGGING
Before moving the unit, lock the adjusting knob.
Take 1 clamps and the safety cord out from the package and mount 2 clamps on the underside of fixture with 2 retainers attached to
each clamp. Hang the fixture on the structure and fasten the screws attached to each clamp. (See the WARNING on the underside of
the base as shown above) To pass the SAFETY CORD through the HOLES for safety! Always ensure that the projector is firmly
anchored to avoid vibration and slipping whilst functioning. Always ensure that the structure that you are going to mount the projector
to is secure and strong enough to support the weight of the unit
(if the unit is without wireless control function, while being hung, the antenna should face down)
●PLACE A UNIT ON A FLAT SURFACE
Before placing a unit on a flat surface, loosen the small knob with the support and make the angle between the arm and the support
60degrees. Tighten the small knob. Loosen he big knob and adjust the angle between the arm and unit as desired and then tighten it.(If
the unit is with wireless control function, after the unit is placed on a flat surface the antenna should face up)
●INSTALLATION OF BARN DOOR
(Two different accessory options:a. Barn Door ;b. Barn door +Frost panel )
If only barn door, its installation is illustrated in the diagram below:
After loosening the butterfly screws(just loosen them, needn’t remove them) in the front of the head and rotating the holding
components in the shape of 7 by 90 degrees, place the barn door into the holding parts in the shape of 7. The installation is completed
after the holding components are rotated backwards , butterfly screws are tightened, and the safety cord with the barn door is run
through the hole in the middle of the head. The light closing effect can be reached by moving the barn door blades.
Barn door
Place
butterfly screws
holding parts in the
shape of 7
-4-
If the frost panel is also selected , it must be used in combination of the barn door. Its Installation and Dismantlement is
illustrated in the diagrams below:
barn door
frost panel
screws ×4
The unit with a barn door is as follow:
●TRANSPORTATION
Before transportation, tighten both knobs after the arm and support are overlapped.
WARNING:
The projector MUST be lifted or carried by the HANDLES instead of clamps.
●.For safety the safety cord should afford 10 times the Projector’s weight.
●
● POWER CONNECTION
Connect the power cord as follows:
L (live) =brown
E (earth) =yellow/green
N (neutral) =blue
Before power connection, please ensure the power supplied must match what the nameplate says. It is recommended that each
projector be connected with power separately so that they may be individually switched on and off.
Note: If projectors are connected in series, please connect POWERIN port of the 1st projector with the Power Mains, then connect its
POWER OUT with POWER IN of the 2nd projector, and so on till all fixtures are connected. If the voltage supplied is 200V-240V,
the maximum projectors connected is 8pcs, if it is 100V-120V, the maximum is 4pcs. The diameter of the cores of the wires for the
2.
Power in/out cables must be equal or bigger than 2.5mm
The earth wire(yellow/green) must be connected to the ground. And electrical connection must be in
accordance with the standards concerned.
●If any questions about the electrical installation, do not continue but consult a qualified electrician.
●
-5-
●DMX CONTROL CONNECTION:
Connection between controller and projector and between one projector and another must be made with a twin-screened cable, with
each wire having at least a 0.5mm in diameter. Connection to and from the projector is via cannon 5 pin (which are included with the
projector) or 5 pin XLR plugs and sockets. The XLR's are connected as shown in the figure above.
Note: care should be taken to ensure that none of the pins touch the metallic body of the plug or each other. XLR plugs and sockets
mustn’t be connected in any way other than mentioned in the above figure. The unit accepts digital control signals in protocol
DMX512 (1990).
Connect the controller’s DMX output to the first fixture’s DMX input, and connect the first fixture’s DMX output to the second
fixture’s DMX input and connect the rest fixtures in the same way. Eventually connect the last fixture’s DMX output to a DMX
terminator as shown in the figure below.
DMX
CONTROLLER
POWER
DMX IN
DMX OUT
DMX OUT
POWER IN
POWER OUT
DMX
TERMINATOR
DMX IN
POWER OUT
POWER IN
●DMX TERMINATOR
In the Controller mode, at the last fixture in the chain, the DMX output has to be connected with a DMX terminator. This prevents
electrical noise from disturbing and corrupting the DMX control signals.
The DMX terminator is simply an XLR connector with a 120 (ohm) resistor connected across pins 2 and 3, which is then plugged
into the output socket on the last projector in the chain. The connections are illustrated below.
DMX TERMINATOR
2
1
3
120
CONNECTION
Connect a 120 (OHM) resistor
across pins 2 and 3 in an XLR plug
and insert into the DMX out socket
on the last unit in the chain.
-6-
PIN 2
PIN 3
5. SETUP AND CONFIGURATION
●FRONT PANEL OPERATION
Projector configuration can be set conveniently via push button and LCD display.
Launch the projector and press button ENTER for more than 3 seconds to unlock the panel, the LCD will show the function menu of
the projector, each main menu has its submenus and each submenu has a specific function. For details, please see the
“OPERATION MENU” section.
Press button UP or DOWN if you want to browse through the various Setup Options.
Press button ENTER to save your settings or enter the submenu.
Press button UP or DOWN to change values(plus or minus)
Press button FUNC, it will return to the upper menu. If button FUNC not pressed, the default will show display status automatically.
●DMX START ADDRESS
Each Projector must be given a DMX start address so that the correct projector responds to the correct control signals. This DMX start
address is the channel number from which the projector starts to “listen” to the digital control information being sent out from the
controller. The Unit has 2 DMX modes. There are standard mode and extended mode. For example standard mode has 7channels,
so set the No. 1 projector’s address 001, No. 2 projector’s address 008, No. 3 projector’s address 014, No. 4 projector’s address020,
and so on.
Launch the projector. Press button ENTER more than 2seconds to unlock panel.
Press button ENTER to display DMX address;
Press button UP and DOWN, you can set the address;
Press button ENTER to confirm; after powered on next time, the default will be last value saved
Press button FUNC, it will return to the upper menu.
●DMX WIRELESS CONTROL (If the projector has the function)
The projector has wireless control function with wireless receiver module and antenna for remote control.
The setup of it is below:
1. Enter into the projector’s menu. Select the menu “Config Settigns” via the bottoms of UP and DOWN
2. Select DMX control Mode---- Wireless First (Note: do not select XLR ONLY),then wireless indication in the
front panel will be on, meaning wireless control function is activated.
Only after the projector is linked with a transmitter, can it receive wireless signal sent by the transmitter. If unlinking it, Press
“Enter” for the menu of Unlink Wireless under the upper level menu of Config Settigns .
●STAND-ALONE MODE
Operate the projector without connecting with a controller, enable the master mode through the operation panel, the
projector will run in Stand-Alone mode automatically.
DMX address can be set at any number within 512.
●MASTER/SLAVE MODE
Many projectors can run synchronously in the Master/Slave mode by linking them with each other. First,
connect the first fixture’s DMX output to the second fixture’s DMX input using XLR-XLR control cable and then connect the second
fixture’s DMX output to the third fixture’s DMX input, and so on until all projector are connected in this way. Eventually connect the
last fixture’s DMX output to a DMX terminator. Set 1st projector as the master and others are Slaves.
Start Addresses of all Slaves are 001; Operation mode of the Master can be set any mode for a Master’ and Slaves’ operation mode can
be set accordingly.
After Powered on, the group will run in Master/Slave Mode
-7-
6. OPERATION MENU
st
(Those contents within the black box are only for the version with wireless control function)
1 level menu
2nd level menu
DMX Address
Standard:001-506
Extended:001-501
3rd level menu
Standard 7
DMX Channel Mode
(Default:STD6)
Extended 12
4th level menu
Default:Standard 7
XLR First
XLR Only
DMX Mode
(Default:XLR First)
(The version without wireless
control does not have the function)
Wireless Only
Wireless First
Default:XLR First
Wireless To XLR
Unlink Wireless
Yes
(The version without wireless
control does not have the function)
No
Brightness
LED OuptControl
(Default: No)
Config Settings
Timer Control
Master/Slave
(Default:Slave)
Slave
Master
Color Offset
Red
Green
Blue
English
Language
(Default:English)
Lcd Light Setup
Default:Slave
128-255
128-255
128-255
Default:English
Chinese
On
Backlight off 3 minutes
Off
after no button pushed
Yes
Display Invert
No
Information
Factory Settings
Parameter Transm
Yes
Yes
Clean Prgra
LED Temperature
Fixture use Time
Yes
Display of Lamp board temperature
Display of Fixture time
X.X.X
Display of Software Version
Software Ver.
Red
Green
Blue
Test Mode
White
RGB
RWB
RGBW
Zoom
DMX Mode
000-255
Yes
User Memory
Preset Memory(PR01~PR16)
Yes
Operation Mode
User Progra Edit
(ET01~ET16)
Dimmer
Strobe
0-255
0-255
Red
Green
0-255
0-255
Blue
White
0-255
0-255
Zoom
Keep Time
0-255
0-255
-8-
Note:
1.
2.
In one DMX chain, only one unit can be made as the master. Before master works, unplug its XLR cable connected with the
console.
The parameters transmitted from the master include after several units are synchronized: DMX channel mode, display
settings(display contrast excluded),operation mode(including user memory).During parameter transmission, set the unit
transmitting data as master and others as slave
7. DMX PROTOCOL
Standard
mode
Extended
mode
Function
DMX
1
1
Zoom
000-255
Linear Zoom (22°-55°)
2
2
Dimming
000-255
Linear Dimming 0%-100%
000-255
Linear adjustment
000-016
No
017-024
White(10000K)
025-032
White(7200K)
033-040
White(5600K)
041-048
White(3200K)
049-056
Cyan
057-064
Yellow
065-072
Magenta
073-080
Red
081-088
Green
089-096
Blue
097-104
Light blue
105-112
Amber
113-120
Orange
121-128
Pink
129-255
Rainbow effect with speed from slow to fast between
3
4
Color Temperature
Color Macros
Description
3
5
Red
000-255
Linear change from light to dark
4
6
Green
000-255
Linear change from light to dark
5
7
Blue
000-255
Linear change from light to dark
6
8
White
000-255
Linear change from light to dark
000-007
7
9
Strobe
No
008-255
Strobe from slow to fast
000
10
Preset memory
No
001-015
Preset memory 1
016-031
Preset memory 2
032-047
Preset memory3
048-063
Preset memory 4
064-079
Preset memory 5
080-095
Preset memory 6
096-111
Preset memory 7
112-127
Preset memory 8
-9-
128-143
Preset memory 9
144-159
Preset memory 10
160-175
Preset memory 11
176-191
Preset memory 12
192-207
Preset memory 13
208-223
Preset memory 14
224-239
Preset memory 15
240-255
Preset memory 16
000
11
12
User Memory
Preset Memory Speed
No
001-015
User Memory1
016-031
User Memory2
032-047
User Memory3
048-063
User Memory4
064-079
User Memory5
080-095
User Memory6
096-111
User Memory7
112-127
User Memory8
128-143
User Memory9
144-159
User Memory10
160-175
User Memory11
176-191
User Memory12
192-207
User Memory13
208-223
User Memory14
224-239
User Memory15
240-255
User Memory16
000-015
Speed 1, fastest
016-031
Speed 2
032-047
Speed 3
048-063
Speed 4
064-079
Speed 5
080-095
Speed 6
096-111
Speed 7
112-127
Speed 8
128-143
Speed 9
144-159
Speed 10
160-175
Speed 11
176-191
Speed 12
192-207
Speed 13
208-223
Speed 14
224-239
Speed 15
240-255
Speed 16, slowest
Note: DMX channel priority: Preset memory> user memory >Macros>RGBW dimming
While higher priority channels are in use, lower priority channels don’t work.
- 10 -
8.
TECHNICAL DATA
INPUT VOLTAGES: 100V~240V AC,50/60Hz
RATED POWER :200W@220V
LIGHT SOURCE SPECIFICATIONS:
Qty
Single COB light source (RGBW)
Power Consumption
150W
Manufacturers Rated Lamp Life
50000hours
COLORS :
R/G/B/W linear color mixing with macros
DIMMING:
Linear Dimming from 0-100%
STROBE:
Electronic Strobe 0.5-33FP.S.
ZOOMING:
DMX linear zooming
BEAM ANGLE:
22°-55°
CONTROL:
DMX512, 3 pin interfaces
7 channels in standard mode and 12 channels in extended mode
Master/Slave Mode
3 Operation Modes(DMX Mode, Preset Memory, user Memory)
Test Mode
OTHER FUNCTIONS:
LED lamp board temperature and fixture time available in the menus
DMX channel mode and settings displayed
LCD and inverted display
Display backlight automatically shut off after delay
Parameters like operation mode and etc. transmitted under synchronization
DMX512 wireless receiver
DMX512 wireless transmitter (optional)
HOUSING:
High tensile cast Aluminum alloy , IP67
Net Weight: 7.5kg
Gross Weight(in Carton): 10.8kg
- 11 -
OPERATION TEMPERATURE:
-20°C~40°C
SIZES:
LIGHT OUTPUT:\
55°(lux)
0
2447
612
272
153
98
68
22°(lux)
0
5371
1640
910
536
389
160
2m
4m
6m
8m
10m
12m
0.78
1.57
2.35
3.14
3.92
4.71
1.92
3.84
5.76
7.69
9.61
11.53
2
0
2
5
3
1
1
3
4
6
5
7
DISTANCE(m) 0m
22°DIAMETER(m) 0
55°DIAMETER(m) 0
- 12 -
55°
4
7
22°
6
9. CIRCUIT DIAGRAM AND PCB CONNECTIONS
●CIRCUIT DIAGRAM
VCC GND
MAX16832-DRIVE-4.PCB
DRV1
Housing
W- B- G- R-
W+ B+ G+ R+
LED
Power IN
W+ W- B+ B- G+ G-R+ R-
J4-PWM
GND
R
G
B
W
Power OUT
ANT
W-DMX
DMX IN
MALE
DMX-IN
WRISSI
PR-8203 MAIN-STM32
FEMALE
DMX-OUT
PWM
M1/Focus
+
-
POWER
Switching power supply-200W
PR-8203
36v
GND
- 13 -
POWER
●PCB CONNECTIONS
Master Board
4
3
2
5
1
No.
Name
Travel Switch for stepping
1
6
7
9
8
motor
2
Thermal switch
3
Wireless board
4
PWM signal
5
Stepping Motor
6
Power supply
7
Signal input
8
Signal output(Reserved)
9
Fan (Reserved)
Slaves
1
2
No.
3
Name
1
LED driver
2
power supply
3
PWM signal input
10. COMPONENT ORDER CODES
No.
Name
Code No.
Qty
Remarks
1
Power Switch
192010201
1
2
LED light source
150020300
1
3
LED Driver Board
230060486
1
4
LCD master board
230060494
1
Only for version with wireless control
230060496
1
Only for version without wireless control
5
Reflector
060060071
1
6
Front Glass Panel
080090114
1
7
Transparent Display Cover
290190109
1
Optional
8
Seal for Transparent Display Cover
290019142
1
Optional
9
Wireless Antenna
W006506
1
Only for version with wireless control
10
Wireless Receiver
W006511
1
Only for version with wireless control
- 14 -
- 15 -
PR LIGHTING LTD.
1582 Xingye Avenue, Nancun Panyu
Guangzhou, 511442 China
TEL: +86-20-3995 2888
PR lighting will try its best to offer accurate and overall information about a product’s technical data. Any changes won’t be notified if necessary. Patented Products.
Counterfeiting Will be Prosecuted!
P/N: 320020431
Version: 20161109
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement