MARK-10 11-1042 Overload Protection Module User's Guide

MARK-10 11-1042 Overload Protection Module User's Guide
11-1042 OVERLOAD PROTECTION MODULE
09-1090 SET POINT CABLE
User’s Guide
11-1042 / 09-1090
SETTING UP
Both the 11-1042 overload protection module and 09-1090 share the same dual
connectors. Each connector is marked and should be configured as follows:
TO LIMIT
SWITCH
CABLE
(OPTIONAL)
TO OUTPUT
CABLE
(OPTIONAL)
LIMITS
PC
A
REVERSE
B
SELECT A OR B
ACCORDING TO
THE TABLE BELOW
STAND
GAUGE
TO TEST
STAND
TO
GAUGE
A
Test stand
model
B
ESM, ESMH,
TSTMH
TSTM, TSFM500,
TSFM500H,
If using the overload protection module and 09-1090 set point cable simultaneously, they should be configured as follows:
09-1090
LIMITS
11-1042
STAND
TO OUTPUT
CABLE
(OPTIONAL)
STAND
TO TEST
STAND
09-1090
PC
PC
11-1042
GAUGE
GAUGE
TO
GAUGE
LIMITS
11-1042 MODULE
TO LIMIT
SWITCH
CABLE
(OPTIONAL)
11-1042 OVERLOAD PROTECTION MODULE
This device is designed to prevent accidental overload to a Mark-10 gauge or
sensor when used with any Mark-10 motorized test stand. Applicable gauges
are the BG, BGI, CG, and EG (if equipped with optional outputs package). The
module operates in both force and torque applications.
Set the percentage of full scale of the gauge or sensor at which the test stand is
to stop moving by adjusting the two potentiometers on the module with a Philips
screwdriver. The percentage range is 20 - 110% of full scale. See the illustration on the following page.
2
User’s Guide
C / CW
This setting applies to the
compression or clockwise
motion of the test stand.
T / CCW
This setting applies to the tension
or counter-clockwise motion of the
test stand.
Once the percentages have been set, set up the test sample and proceed
with the motorized test. When the force or torque threshold has been
reached, the stand will stop moving, the module will produce a constant
audible tone and the indicator below the potentiometer will be lit. The tone
and indicator light will not turn off until the force or torque decreases to
below the threshold value.
Note: It is highly recommended that the first test be performed at low speed to ensure that the module is functioning properly.
09-1090 SET POINT CABLE
This cable is designed to stop the motion of any Mark-10 motorized test stand
travel at user-programmable set points with a BG, BGI, or CG gauge. Refer to
your gauge’s user’s guide for programming instructions.
Cable configuration instructions are provided on the previous page.
WARRANTY
Mark-10 Corporation expressly warrants to its buyer for three (3) years from the date of
delivery that the goods sold are free from defects in workmanship and materials. Mark-10
Corporation will, at its option, repair or replace or refund the purchase price of goods
found to be defective. This remedy shall be the buyer’s sole and exclusive remedy. Any
modification, abuse, exposure to corrosive environment or use other than intended will
void this warranty. This warranty is in lieu of all other warranties, including implied warranties of merchantability and fitness for an intended purpose. In no event shall Mark-10
Corporation be liable for any incidental and consequential damages in connection with
goods sold or any part thereof.
3
Mark-10 Corporation has been an innovator in the Force and Torque
measurement fields since 1979. We strive to achieve 100% customer
satisfaction through excellence in product design, manufacturing and
customer support. In addition to our standard line of products we can
provide modifications and custom designs for OEM applications. Our
engineering team is eager to satisfy any special requirements. Please
contact us for further information or suggestions for improvement.
We make a measurable difference in force and torque measurement
Mark-10 Corporation
11 Dixon Avenue
Copiague, NY 11726 USA
1-888-MARK-TEN
Tel: 631-842-9200
Fax: 631-842-9201
Internet: www.mark-10.com
Email: info@mark-10.com
32-1038
REV 2 0710
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement