Microscan HS-360X "Ultra-Rugged" Direct Part Mark Handheld Scanner User Manual

advertisement

Microscan HS-360X "Ultra-Rugged" Direct Part Mark Handheld Scanner User Manual
HS-360X Handheld DPM Scanner
User Manual
P/N 84-9000360-02 Rev D
Copyright and Disclaimers
Copyright ©2019
Omron Microscan Systems, Inc.
Tel: +1.425.226.5700 / 800.762.1149
Fax: +1.425.226.8250
All rights reserved. The information contained herein is proprietary and is provided solely for the purpose
of allowing customers to operate and/or service Omron Microscan-manufactured equipment and is not to
be released, reproduced, or used for any other purpose without written permission of Omron Microscan.
Throughout this manual, trademarked names might be used. We state herein that we are using the names
to the benefit of the trademark owner, with no intention of infringement.
Disclaimer
The information and specifications described in this manual are subject to change without notice.
Latest Manual Version
For the latest version of this manual, see the Download Center on our web site at:
www.microscan.com/downloadcenter.
ii
HS-360X Handheld DPM Scanner User Manual
Introduction
No part of this publication may be reproduced or used in any form, or by any electrical or mechanical means, without
permission in writing from Omron Microscan. This includes electronic or mechanical means, such as photocopying,
recording, or information storage and retrieval systems. The material in this manual is subject to change without notice.
The software is provided strictly on an “as is” basis. All software, including firmware, furnished to the user is on a
licensed basis. Omron Microscan grants to the user a non-transferable and non-exclusive license to use each
software or firmware program delivered hereunder (licensed program). Except as noted below, such license may
not be assigned, sublicensed, or otherwise transferred by the user without prior written consent of Omron
Microscan. No right to copy a licensed program in whole or in part is granted, except as permitted under copyright
law. The user shall not modify, merge, or incorporate any form or portion of a licensed program with other program
material, create a derivative work from a licensed program, or use a licensed program in a network without written
permission from Omron Microscan. The user agrees to maintain Omron Microscan’s copyright notice on the
licensed programs delivered hereunder, and to include the same on any authorized copies it makes, in whole or in
part. The user agrees not to decompile, disassemble, decode, or reverse engineer any licensed program delivered
to the user or any portion thereof.
Omron Microscan reserves the right to make changes to any product to improve reliability, function, or design.
Omron Microscan does not assume any product liability arising out of, or in connection with, the application or use
of any product, circuit, or application described herein. No license is granted, either expressly or by implication,
estoppel, or otherwise under any patent right or patent, covering or relating to any combination, system, apparatus,
machine, material, method, or process in which Omron Microscan products might be used. An implied license
exists only for equipment, circuits, and subsystems contained in Omron Microscan products.
This product may include Seller Software, Third Party Software, and/or Publicly Available Software.
Use of any Software is subject to the applicable licenses, terms and conditions of the agreement in force between
you and the Seller unless a separate License is included, in which case, use of the Software will be governed by the
separate License.
Copies of the licenses for the following Publicly Available Software, and all attributions, acknowledgments, and
software information details, are included below. Seller is required to reproduce the software licenses,
acknowledgments and copyright notices as provided by the Authors and Owners. The information is provided in its
native language form, without modification or translation.
Publicly available software list:
Name: Regular Expression Evaluator
Version: 8.3
Description: Compiles and executes regular expressions.
Software Site: http://www.freebsd.org/cgi/cvsweb.cgi/src/lib/libc/regex/
Source Code: No Source Distribution Obligations. Seller will not provide nor distribute the Source Code for the
Regular Expression Evaluator.
License: BSD Style License
©1992 Henry Spencer.
©1992, 1993 The Regents of the University of California. All rights reserved.
This code is derived from software contributed to Berkeley by Henry Spencer of the University of Toronto.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the
following conditions are met:
1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following
disclaimer in the documentation and/or other materials provided with the distribution.
3. All advertising materials mentioning features or use of this software must display the following acknowledgment:
This product includes software developed by the University of California, Berkeley and its contributors.
4. Neither the name of the University nor the names of its contributors may be used to endorse or promote products
derived from this software without specific prior written permission.
THIS SOFTWARE IS PROVIDED BY THE REGENTS AND CONTRIBUTORS ``AS IS'' AND ANY EXPRESS OR
IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL
THE REGENTS OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR
TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
HS-360X Handheld DPM Scanner User Manual
iii
Table of Contents
Table of Contents
Introduction
Table of Contents .......................................................................................iv
About This Manual .................................................................................... vii
HS-360X Configurations........................................................................... viii
Service Information ....................................................................................ix
Revision History ..........................................................................................x
Chapter 1
Quick Start
HS-360X Handheld DPM Scanner .......................................................... 1-2
HS-360X Wireless Handheld DPM Scanner ........................................... 1-4
HS-360X Wired Handheld DPM Scanner.............................................. 1-14
Chapter 2
Data Capture
HS-360X Wireless Scanner Beeper and LED ......................................... 2-2
HS-360X Beeper and LED Definitions .................................................... 2-7
HS-360X Scanning .................................................................................. 2-8
Chapter 3
Maintenance and Technical Specifications
Maintenance ............................................................................................ 3-2
Troubleshooting....................................................................................... 3-4
Technical Specifications .......................................................................... 3-7
HS-360X Wired Scanner Signal Descriptions ....................................... 3-10
Chapter 4
Radio Communications
HS-360X Wireless Scanner Radio Communications............................... 4-2
Radio Communications Parameter Defaults ........................................... 4-3
Wireless Beeper Definitions .................................................................... 4-5
Radio Communications Host Types ........................................................ 4-5
Bluetooth-Friendly Name......................................................................... 4-9
Wi-Fi Friendly Mode .............................................................................. 4-11
Radio Output Power .............................................................................. 4-14
Bluetooth Radio State ........................................................................... 4-16
HID Host Parameters ............................................................................ 4-17
Reconnect Attempt Beep Feedback...................................................... 4-29
Out-of-Range Indicator .......................................................................... 4-34
Beep on <BEL> ..................................................................................... 4-36
Scanner(s)-to-Cradle Support ............................................................... 4-37
Batch Mode ........................................................................................... 4-46
Persistent Batch Storage....................................................................... 4-50
Page Button........................................................................................... 4-51
Page Options......................................................................................... 4-52
Classic Bluetooth and/or Low Energy (Cradle Host Only)..................... 4-54
Bluetooth Security ................................................................................. 4-55
Bluetooth Radio, Linking, and Batch Operation ................................... 4-59
Chapter 5
User Preferences and Miscellaneous Options
Introduction.............................................................................................. 5-2
Scanning Sequence Examples ............................................................... 5-2
iv
HS-360X Handheld DPM Scanner User Manual
Introduction
Errors While Scanning ............................................................................. 5-2
Parameter Defaults.................................................................................. 5-3
User Preferences..................................................................................... 5-5
Chapter 6
Imaging Preferences
Introduction .............................................................................................. 6-2
Scanning Sequence Examples................................................................ 6-3
Errors While Scanning ............................................................................. 6-3
Imaging Preferences Parameter Defaults ............................................... 6-3
Chapter 7
USB Interface
Connecting a USB Interface ................................................................... 7-2
USB Parameter Defaults ......................................................................... 7-5
USB Host Parameters ............................................................................. 7-6
Optional USB Parameters ................................................................ .....7-20
ASCII Character Set for USB ................................................................ 7-26
Chapter 8
RS-232 Interface
Introduction .............................................................................................. 8-2
Connecting an RS-232 Interface ............................................................. 8-3
RS-232 Parameter Defaults .................................................................... 8-5
ASCII Character Set for RS-232............................................................ 8-23
Chapter 9
Symbologies
Introduction .............................................................................................. 9-2
Scanning Sequence Examples................................................................ 9-2
Errors While Scanning ............................................................................. 9-2
Symbology Parameter Defaults ............................................................... 9-3
Enable/Disable All Code Types ............................................................... 9-8
UPC/EAN................................................................................................. 9-9
Code 128 ............................................................................................... 9-36
Code 39 ................................................................................................. 9-48
Code 93 ................................................................................................. 9-60
Code 11 ................................................................................................. 9-63
Interleaved 2 of 5 (ITF) .......................................................................... 9-68
Discrete 2 of 5 (DTF) ............................................................................. 9-77
Codabar (NW - 7) .................................................................................. 9-80
MSI ........................................................................................................ 9-86
Chinese 2 of 5 ....................................................................................... 9-92
Matrix 2 of 5 ........................................................................................... 9-93
Korean 3 of 5 ......................................................................................... 9-98
Inverse 1D ............................................................................................. 9-99
GS1 DataBar ....................................................................................... 9-100
BC412.................................................................................................. 9-105
Composite ........................................................................................... 9-106
PDF417 ............................................................................................... 9-112
MicroPDF417....................................................................................... 9-113
Code 128 Emulation ............................................................................ 9-114
Data Matrix .......................................................................................... 9-115
HS-360X Handheld DPM Scanner User Manual
v
Table of Contents
GS1 Data Matrix .................................................................................. 9-115
Data Matrix Inverse ............................................................................. 9-116
Maxicode ............................................................................................. 9-117
QR Code ............................................................................................. 9-118
GS1 QR ............................................................................................... 9-119
Micro QR Code.................................................................................... 9-120
Aztec ................................................................................................... 9-121
Aztec Inverse....................................................................................... 9-122
Han Xin................................................................................................ 9-123
Han Xin Inverse ................................................................................... 9-124
DotCode .............................................................................................. 9-125
U.S. Postnet ........................................................................................ 9-126
U.S. Planet .......................................................................................... 9-127
UK Postal ............................................................................................ 9-129
Japan Postal........................................................................................ 9-131
Australia Post ...................................................................................... 9-132
Netherlands KIX Code......................................................................... 9-135
USPS 4CB/One Code/Intelligent Mail ................................................. 9-136
UPU FICS Postal................................................................................. 9-137
Mailmark .............................................................................................. 9-138
Symbology-Specific Security Levels ................................................... 9-139
Report Version .................................................................................... 9-145
Macro PDF Features ........................................................................... 9-146
Chapter 10
WebLinkPC
Overview ............................................................................................... 10-2
Quick Start............................................................................................. 10-9
Start ..................................................................................................... 10-30
Setup ................................................................................................... 10-35
Run ...................................................................................................... 10-46
Application Settings ............................................................................. 10-47
Advanced Settings .............................................................................. 10-57
Appendices
Appendix A — Standard Default Parameters .................................................A-2
Appendix B — Country Codes......................................................................A-11
Appendix C — Country Code Pages ............................................................A-31
Appendix D — Chinese, Japanese, and Korean (CJK) Decode Control ......A-44
Appendix E — Programming Reference ......................................................A-53
Appendix F — Sample Symbols ...................................................................A-59
Appendix G — Alphanumeric Keyboard .......................................................A-62
Appendix H — Numeric Keyboard................................................................A-77
Appendix I — ASCII Character Sets.............................................................A-79
Appendix J — Non-Parameter Attributes .....................................................A-90
vi
HS-360X Handheld DPM Scanner User Manual
Introduction
About This Manual
The HS-360X Handheld DPM Scanner User Manual provides general instructions for setting up,
operating, maintaining, and troubleshooting wireless and wired HS-360X scanners.
Notational Conventions
The following conventions are used in this document:
Italics are used to highlight the following:
• Chapters and sections in this and related documents;
• Dialog box, window and screen names;
• Drop-down list and list box names;
• Check box and radio button names.
Bold text is used to highlight the following:
• Key names on a keypad;
• Button names on a screen.
Bullets (•) indicate:
• Action items;
• Lists of alternatives.
Lists of required steps that are not necessarily sequential:
• Sequential lists (e.g., those that describe step-by-step procedures) appear as numbered lists.
• Throughout the programming barcode menus, asterisks (*) are used to denote default
parameter settings.
* Indicates Default
* HID Keyboard Emulation
Feature/Option
Related Documents
• HS-360X Wired Scanner Quick Start Guide, P/N 83-9310013-02, provides general
information about how to get started with the wired version of the HS-360X Handheld
DPM Scanner, and includes basic instructions for setup and operation.
• HS-360X Wireless Scanner Quick Start Guide, P/N 83-9310014-02, provides general
information about how to get started with the wireless version of the HS-360X Handheld
DPM Scanner, and includes basic instructions for setup and operation.
• HS-360X Four-Slot Spare Battery Charger Quick Start Guide, P/N 83-93100017-02,
provides general information about how to mount, configure, and use the HS-360X
Four-Slot Spare Battery Charger.
• HS-360X Cradle Quick Start Guide, P/N 83-93100018-02, provides general information
about how to mount, connect, configure, and use the HS-360X Cradle.
For the latest version of all guides, visit the Download Center at: www.microscan.com.
HS-360X Handheld DPM Scanner User Manual
vii
Table of Contents
HS-360X Configurations
This guide includes the following HS-360X configurations:
Part Number
Description
HDS-3608-0001
HS-360X Handheld DPM Scanner, Wired
HDS-3678-0001
HS-360X Handheld DPM Scanner, Wireless
HS-360X Accessories, Cables, and Power Supplies
Caution: Use only cables designed for the HS-360X Handheld DPM Scanner.
Part Number
Description
Accessories
12-9000937-01
Cradle / Charger, HS-360X Wireless
98-9000185-01
4-Slot Battery Charger, HS-360X Wireless, Power Supply Required
98-9000186-01
Stand, HS-360X
98-9000224-01
Battery, Spare, HS-360X Wireless
USB Cables
12-9000942-01
Cable, USB, Shielded, 2 M, Ext. 12V, HS-360X, Power Supply Required
12-9000943-01
Cable, USB, Shielded, 4.6 M, Ext. 12V, HS-360X, Power Supply Required
12-9000946-01
Cable, USB, Shielded, 2 M, HS-360X
12-9000947-01
Cable, USB, Shielded, 4.6 M, HS-360X
RS-232 Cables
12-9000953-01
Cable, RS-232, DB9 Socket, 2 M, Straight, HS-360X, 98-9000181-01 and A/C Power Cord Required
Power Supplies
12-9000959-01
AC Power Cord, 2.5 M, U.S., C13 Conn.
12-9000960-01
AC Power Cord, 2.5 M, EU, C13 Conn.
12-9000961-01
AC Power Cord, 2.5 M, UK, C13 Conn.
12-9000962-01
AC Power Cord, 2.5 M, China, C13 Conn.
12-9001046-01
AC Power Cord, 1.8 M, Japan, C13 Conn.
98-9000181-01
Kit, Power Supply for Cradle / Charger, HS-360X Wireless / RS-232 Cable, A/C Power Cord Required
98-9000182-01
Kit, Power Supply for 4-Slot Battery Charger, HS-360X, A/C Power Cord Required
viii
HS-360X Handheld DPM Scanner User Manual
Introduction
Service Information
If you have a problem using the equipment, contact your facility's technical or systems
support. If there is a problem with the equipment, you can contact customer service at:
www.microscan.com.
When contacting support, please have the following information available:
• Serial number of the unit
• Model number or product name
• Software type and version number
Omron Microscan responds to calls by e-mail, telephone or fax within the time limits set forth
in service agreements.
If your problem cannot be solved by support, you may need to return your equipment for
servicing and will be given specific directions. Omron Microscan is not responsible for any
damages incurred during shipment if the approved shipping container is not used. Shipping
the units improperly can possibly void the warranty.
If you purchased your product from an Omron Microscan business partner, please contact
that partner for support.
HS-360X Handheld DPM Scanner User Manual
ix
Table of Contents
Revision History
The revision level is found in the lower right-hand corner of the front cover to the right of the
document part number, and also in the lower right-hand corner of the contact information on
the last page of the manual.
Revision
Revision Date
Rev A
May 2018
First publication.
Rev B
July, 2018
General improvements.
Rev C
May, 2019
Expansion of WebLinkPC content, addition of read range diagram,
addition of revision history, addition of contact information page.
Rev D
June, 2019
Revision of read range diagram.
x
Reason for Revision
HS-360X Handheld DPM Scanner User Manual
1 Quick Start
This section provides a product overview, unpacking instructions, and configuration information.
HS-360X Handheld DPM Scanner User Manual
1-1
HS-360X Handheld DPM Scanner
HS-360X Handheld DPM Scanner
The wireless HS-360X combines superior 1D and 2D omnidirectional barcode scanning
performance and advanced ergonomics in a lightweight design. The scanner design ensures
comfort and ease of use over extended periods of time.
Important: A PowerPrecision+ 3100 mAh Li-Ion rechargeable battery is included with wireless
versions of the HS-360X.
HS-360X Wireless Handheld DPM Scanner
The wired HS-360X combines superior 1D and 2D omnidirectional barcode scanning performance
and advanced ergonomics in a lightweight, hands-free / handheld design. The HS-360X
Stand seamlessly accommodates both countertop and handheld use.
HS-360X Wired Handheld DPM Scanner
1-2
HS-360X Handheld DPM Scanner User Manual
Quick Start
The HS-360X Handheld DPM Scanner Supports:
• USB connection to a host. The scanner autodetects a USB host and defaults to HID
keyboard. Select other USB interface types by scanning programming symbol menus.
The USB interface supports the following international keyboards for a Windows®
environment: North American English, Japanese, German, French, French Canadian,
Spanish, Italian, Swedish, UK English, and Brazilian Portuguese.
• Standard RS-232 connection to a host. Scan programming symbol menus to set up
communication between the scanner with the host.
Important: An RS-232 connection is not compatible with WebLinkPC configuration
software, and offers only limited programming options.
• Configuration via WebLinkPC.
Unpacking
Remove the scanner from its packaging and inspect it for damage. If the scanner was damaged
during shipping, contact Omron Microscan support. KEEP THE PACKING MATERIALS. They
comprise the approved shipping container, which you can use to return the scanner for servicing.
HS-360X Handheld DPM Scanner User Manual
1-3
HS-360X Wireless Handheld DPM Scanner
HS-360X Wireless Handheld DPM Scanner
Parts
Battery LED
Radio LED
Scan Window
Charging/Communication
Contacts
Trigger
LEDs
Battery Latch
Beeper
1-4
HS-360X Handheld DPM Scanner User Manual
Quick Start
The HS-360X Cradle
The HS-360X Cradle is a charger, radio communication interface, and host communication
interface for the HS-360X Wireless Scanner.
The wireless cradle charges the scanner and provides host communication by receiving scanner
data via a Bluetooth radio, and sending that data to the host through an attached cable. An
external power supply or a powered host cable provides power to the cradle.
For more mounting options, refer to the HS-360X Cradle Quick Start Guide, P/N 83-9310018-02,
included with the cradle.
Cradle – Front View
Canopy Latch
PAIR
Pairing Barcode
Drain Holes
Mounting Screw Hole
Mounting Screw Hole
Charging/Communications
Contacts
Page Button
LEDs
Foot Latch
Drain Hole
Mounting Screw Hole
Cradle – Back View
Rubber Feet
Mounting Screw Holes
Host Cable Latch
Host Cable (Under Latch)
Host Cable Guide
Foot Latch Release
Mounting Screw Holes
Rubber Feet
HS-360X Handheld DPM Scanner User Manual
1-5
HS-360X Wireless Handheld DPM Scanner
Connecting the Cradle
Note: The interface cable and power supply (if necessary) in the following order to ensure
proper operation of the scanner and cradle.
To connect the HS-360X Cradle:
1. Connect the appropriate cable to the power supply and an AC power source, if necessary.
2. Insert the interface cable into the host port.
3. Lift the latch and connect the interface cable into the cradle's host port and then close
the latch.
4. If applicable, thread the interface cable over the cable support hook and run the host
cable into the cable groove.
5. Pair the scanner to the cradle either by inserting it in the cradle (if pair on contacts is
enabled), or by scanning the pairing symbol.
6. If necessary, scan the appropriate host symbol (for non-autodetected interfaces). See
the specific host chapter.
Latch
Host Port
(Under Latch)
Important: Be sure that the
interface cable is pushed all
the way into the host port
before you close the latch.
Connecting the Cables to the Cradle
Note: Always disconnect the DC power supply BEFORE disconnecting the cable to
the host end or the cradle may not recognize the new host.
Note: Different cables are required for different hosts. The connectors illustrated in
each host chapter are examples only. The connectors may be different from those
illustrated, but the steps to connect the scanner remain the same.
1-6
HS-360X Handheld DPM Scanner User Manual
Quick Start
Supplying Power to the Cradle
The cradle receives power from one of two sources:
• An external power supply.
• When connected to the host through an interface cable that supplies power.
The cradle detects whether the host or the external supply is supplying power. It always
draws power from the external supply when available, regardless of the presence of power
from a host.
Mounting the Cradle
For information on mounting the cradle, refer to the documentation included with the cradle.
Wireless HS-360X Battery
Battery Statistics Capabilities
The HS-360X Wireless Scanner is equipped with PowerPrecision+ batteries. These
intelligent batteries have the integrated technology required to collect the detailed real-time
battery metrics needed to maximize useful battery life and ensure every battery is healthy
and able to hold a full charge.
PowerPrecison+ batteries support the following remote management functionality:
• Battery Asset Information
• Manufacture Date of Battery
• Serial Number of Battery
• Model Number of Battery
• Firmware Version of Battery
• Design Capacity
• Battery Life Statistics
• State of Health Meter
• Charge Cycles Consumed
• Battery Status (at Time of Poll)
• State of Charge
• Remaining Capacity
• Charge Status
• Remaining Time to Complete Charging
• Battery Voltage / Current
• Battery Temperature
• Present / Highest / Lowest
Battery statistics can be viewed in WebLinkPC by following these steps:
1. Select Wireless Scanner in the Start menu.
2. From the Advanced Settings menu, go to the Battery tab.
Hint: ALT+A opens the Advanced Settings tab for the selected scanner.
HS-360X Handheld DPM Scanner User Manual
1-7
HS-360X Wireless Handheld DPM Scanner
Inserting the Wireless HS-360X Battery
A PowerPrecision+ 3100 mAh Li-Ion rechargeable battery ships with each wireless HS-360X.
Batteries are shipped in an Off mode and do not power the scanner. After inserting a new
battery into the HS-360X scanner, you must insert the scanner into a cradle for the battery to
turn On.
Alternatively, the battery can be placed in the four slot spare battery charger to charge and
then inserted in the scanner for immediate use.
The battery resides in a chamber in the scanner handle. To insert the battery:
1. Lightly press down and slide the locking lever counterclockwise to unlock and
release the battery door.
2. Open the battery door.
3. If a battery is already installed, turn the scanner upright to slide the battery out.
4. Slide the new battery into the chamber, with the rounded side toward the back and
the contacts facing into the chamber.
Unlock
Lock
Inserting the Battery
1. Close the battery door.
2. Lightly press down and slide the locking lever clockwise to lock the battery door.
3. If using a brand new battery, insert the scanner into a cradle to turn the battery on.
Removing the HS-360X Battery
To remove the battery:
1. Lightly press down and slide the locking lever counterclockwise to unlock the battery door.
2. Open the battery door.
3. Turn the scanner upright to slide the battery out.
1-8
HS-360X Handheld DPM Scanner User Manual
Quick Start
Charging the HS-360X Battery
When using a new battery in the HS-360X, the battery requires a charge to be enabled.
Insert the battery in the HS-360X and place the HS-360X in the cradle.
The battery begins charging when the cradle’s LED indicator starts blinking amber. The
HS-360X’s battery has completed a charge when the cradle’s LED indicator is solid green. A
complete charge of a fully discharged battery can take up to three hours using external
power and up to ten hours using USB power over the USB interface cable.
To avoid a battery temperature fault, always charge the battery in the scanner within the
recommended temperature of 32° to 104° F (0° to 40° C) nominal, 41° to 95° F (5° to 35° C) ideal.
Inserting the HS-360X Scanner in the Cradle
To insert the scanner in the cradle:
1. Insert the scanner into the cradle top first.
2. Push the handle until it clicks into place, engaging the contacts in the cradle and scanner.
Inserting the Scanner in the Cradle
HS-360X Handheld DPM Scanner User Manual
1-9
HS-360X Wireless Handheld DPM Scanner
Sending Data to the Host Computer
The cradle receives data from the scanner via a wireless radio connection and transmits it to
the host computer via the host cable. The scanner and cradle must be paired for successful
wireless communication.
Pairing
Pairing registers a scanner to the cradle such that the scanner and cradle can exchange
information. The cradle operates in two modes: Point-to-Point and Multipoint-to-Point. In
Point-to-Point mode, pair the scanner to the cradle either by inserting it in the cradle (if pair
on contacts is enabled), or by scanning the pairing symbol. In Multipoint-to-Point mode, you
can pair up to seven scanners to one cradle.
To pair the scanner with the cradle, scan a pairing symbol. A high-low-high-low beep sequence
followed by a low-high beep sequence indicates successful pairing and connection to the
remote device. A long low, long high beep sequence indicates unsuccessful pairing.
The pairing symbol that connects the scanner to a cradle is unique to each cradle.
Do not scan data or parameters until pairing completes.
Lost Connection to Host
If scanned data does not transmit to the cradle's host, ensure that all cables are firmly
inserted and the power supply is connected to an appropriate AC outlet, if applicable. If
scanned data still does not transmit to the host, reestablish a connection with the host:
1. Disconnect the power supply from the cradle.
2. Disconnect the host interface cable from the cradle.
3. Wait three seconds.
4. Reconnect the host interface cable to the cradle.
5. Reconnect the power supply to the cradle, if the host requires.
6. Reestablish pairing with the cradle by scanning the pairing symbol.
Configuring the Scanner
Use the configuration symbols in this manual or the WebLinkPC configuration program to
configure the scanner.
Radio Communications
The scanner can communicate with remote devices via Bluetooth, or by pairing with a cradle.
1-10
HS-360X Handheld DPM Scanner User Manual
Quick Start
Four-Slot Spare Battery Charger
The battery charger can accomodate up to four single spare batteries. The charger can sit
on a desktop or be mounted on a wall. This document provides basic instructions for charger
set up and use.
For best performance, fully charge the device battery before using the device for the first
time. To charge the
device battery, insert the battery in the cradle. The battery begins charging when the LED
indicator on the battery charger starts flashing amber. A complete charge of a fully discharged
battery can take up to five hours. Charge within the recommended temperature of 32° to
104° F (0° C to 40° C) nominal, 41° to 95° F (5° to 35° C) ideal.
Battery Charging LED (four)
Battery
Well
(four)
Wall Mount
Key-Hole (two)
Power Cable
Groove
Rubber Feet (four)
Power Port
USB Port
Four-Slot Spare
Battery Charger
Power
Cable Well
Cable Groove(s)
HS-360X Handheld DPM Scanner User Manual
1-11
HS-360X Wireless Handheld DPM Scanner
Inserting Batteries
To insert batteries in the battery charger, angle the battery with the contacts facing up and
slide the contact side of the battery under the LED indicator ledge as shown below. Push
down on the label surface of the battery until it clicks in place, engaging the contacts in the
battery charger.
Inserting
Batteries
Lanyard
Do not attach the tool balancer to the lanyard slot at the bottom of the device.
To install the optional lanyard:
1. Insert the loop on the lanyard into the slot at the bottom of the device handle.
Insert Lanyard Loop
1-12
HS-360X Handheld DPM Scanner User Manual
Quick Start
2. Thread the upper portion of the lanyard into the loop.
Thread the Loop
3. Pull the clip through the loop over the tether point and tighten into place.
Insert Loop into Tether Point
HS-360X Accessories
The scanner ships with a battery and the HS-360X Wireless Scanner Quick Start Guide.
The following required accessories must be ordered:
• Interface cable for the appropriate interface.
• Universal power supply, if the interface requires this.
HS-360X Handheld DPM Scanner User Manual
1-13
HS-360X Wired Handheld DPM Scanner
HS-360X Wired Handheld DPM Scanner
Parts
Scan Window
LEDs
Beeper
Trigger
1-14
HS-360X Handheld DPM Scanner User Manual
Quick Start
Installing the HS-360X Interface Cable
1. Insert cable fully so that the connector is flush with the scanner surface.
Important: Be sure the interface cable is pushed
all the way into the connector before closing and
fastening the lock plate.
Inserting Cable into HS-360X
2. Loosen metal lock plate screw using a PH1 driver.
Loosening HS-360X Lock Plate Screw
3. Slide lock plate to fully locked position.
Sliding Lock Plate into Locked Position
HS-360X Handheld DPM Scanner User Manual
1-15
HS-360X Wired Handheld DPM Scanner
4. Tighten lock plate screw using a PH1 driver (recommended Torque: 5 in-lbs).
Tightening Lock Plate
Removing the HS-360X Interface Cable
1. Loosen lock plate screw using a PH1 driver.
Loosening Lock Plate
2. Slide lock plate to fully unlocked position.
Sliding Lock Plate into Unlocked Position
1-16
HS-360X Handheld DPM Scanner User Manual
Quick Start
3. Tighten lock plate to fully unlocked position.
Tightening Lock Plate into Unlocked Position
4. Remove cable.
Removing Cable from HS-360X
HS-360X Handheld DPM Scanner User Manual
1-17
HS-360X Wired Handheld DPM Scanner
Connecting Power to the HS-360X (If Required)
If the host does not provide power to the scanner, connect an external power supply.
1. Plug the power supply into the power jack on the interface cable.
2. Plug the other end of the power supply into an AC outlet.
Configuring the HS-360X Scanner
Use the configuration symbols included in this manual, or WebLinkPC software, to configure
the scanner.
HS-360X Accessories
The scanner ships with the HS-360X Wired Scanner Quick Start Guide. The following required
accessories must be ordered:
• Interface cable for the appropriate interface.
• Universal power supply, if the interface requires this.
• HS-360X Stand for hands-free operation of the scanner.
1-18
HS-360X Handheld DPM Scanner User Manual
2 Data Capture
This section provides beeper and LED definitions, techniques involved in scanning barcodes,
general instructions and tips about scanning, and decode ranges.
HS-360X Handheld DPM Scanner User Manual
2-1
HS-360X Wireless Scanner Beeper and LED
HS-360X Wireless Scanner Beeper and LED
The scanner issues different beep sequences/patterns and an LED display to indicate status.
Radio and Beeper LED Definitions
In addition to the System/Decode LEDs, the HS-360X Wireless Scanner has a Radio and
Battery LED gauge.
The Radio and Battery LED gauge is always active when inserted in the cradle. After the
scanner is removed from the cradle, it is active for four seconds.
After the trigger is held for three seconds the Radio and Battery LED gauge remain active for
four seconds after trigger release.
See the following page for a complete list of definitions.
2-2
HS-360X Handheld DPM Scanner User Manual
Data Capture
HS-360X Wireless Scanner Beeper and LED Definitions
Event
Beeper Sequence
LED
Low/medium/high beeps
Green
Standard Use
Power up.
Scanning
Presentation Mode on.
None
Green solid
Presentation Mode off.
None
No LED; green LED is turned off
A barcode was successfully
decoded.
Medium beep (or as configured)
Green flash
Parity error.
Low/low/low/extra low beeps
Red
A transmission error was detected
in a scanned symbol. The data is
ignored. This occurs if a unit is not Four long low beeps
properly configured. Check option
setting.
Red
Conversion or format error.
Five long low beeps
Red
A <BEL> character is received
over RS-232.
High
None
Low, high, low, high
Red
Low
System LED: None
Radio LED: None
Wireless Operation
Out of batch storage memory,
unable to store new barcode.
Radio Indications
Scanner inserted into a cradle
(may be disabled).
Bluetooth connection established. Low, high
System LED: Green
Radio LED: Green (Stays on after
trigger hold for 3 seconds)
Bluetooth disconnection event.
System LED: Red
Radio LED: Red (Stays on at
trigger pull)
High, low
Bluetooth Page timeout; remote
Long low, long high
device is out of range/not powered.
System LED: Red
Radio LED: Red (Stays on at
trigger pull)
System LED: None
Bluetooth connection attempt was Long low, long high, long low, long
Radio LED: Red (Stays on at
rejected by remote device.
high
trigger pull)
Bluetooth attempting reconnection. None
System LED: None
Radio LED: Red blinking
Bluetooth attempting reconnection
Five high
(default is disable).
System LED: None
Radio LED: Red blinking
Paging state indication
System LED: Blue (fast, fast, slow)
Six high
HS-360X Handheld DPM Scanner User Manual
2-3
HS-360X Wireless Scanner Beeper and LED
Event
Beeper Sequence
LED
Four short high beeps
Red (stays on)
Battery Indications
Low battery indication (on trigger
release)
Battery LED status
99-51% Green
21-50% Amber
0-20% Red
Battery end of life
99-51% Green/red alternating
21-50% Amber/red alternating
0-20% Red blinking
Parameter Programming
Input error, incorrect barcode or
Cancel scanned, wrong entry,
incorrect barcode programming
sequence; remain in program
mode.
Long low/long high beeps
Red
Keyboard parameter selected.
High/low beeps
Enter value using barcode keypad.
Green
Successful program exit with
change in the parameter setting.
Green
High/low/high/low beeps
Cancel rule entry. Rule entry mode
Green
exited because of an error or the Long low/long high/long low beeps
(turns off blinking)
user asked to exit rule entry.
Host-Specific: USB-Only
Scanner has not completed
initialization. Wait several seconds Four high beeps
and scan again.
None
Host-Specific: RS-232-Only
RS-232 receive error.
High/high/high/low beeps
Red
A <BEL> character is received
when Beep on <BEL> is enabled
(Point-to-Point mode only).
High beep
None
2-4
HS-360X Handheld DPM Scanner User Manual
Data Capture
Cradle LED Definitions
Event
LED
Standard Use
Power Up
Green (stays on)
Radio Indications
Bluetooth connection established
Green (off then on)
Page button
Blue
Battery Indications
Pre-charging
Amber (stays on)
Charging
Amber blinking
Fully charged
Green (stays on)
Charging Error
Amber fast blinking
Battery End of Life Indications
Charging
Red blinking
Fully charged
Red (stays on)
Charging error
Red fast blinking
Maintenance Indications
Enter boot loader
Red (stays on)
Firmware installation
Red blinking
HS-360X Handheld DPM Scanner User Manual
2-5
HS-360X Wireless Scanner Beeper and LED
Four-Slot Battery Charger Definitions
Event
LED
Standard Use
Power Up
Red, amber, green, off (all four LEDs)
Idle
Off
Battery Indications
Pre-charging
Amber (stays on)
Charging
Amber blinking
Fully charged
Green (stays on)
Charging error
Amber fast blinking
Battery End of Life Indications
Charging
Red blinking
Fully charged
Red (stays on)
Charging error
Red fast blinking
Maintenance Indications
Enter bootloader
Red (stays on; all four LEDs)
Firmware installation
Red blinking (all four LEDs)
2-6
HS-360X Handheld DPM Scanner User Manual
Data Capture
HS-360X Beeper and LED Definitions
In addition to beep sequences, the scanner uses a two-color LED to indicate status.
Event
Beeper Sequence
LED Indicator
Power up.
Low, Medium, High beeps
Green
Standard Use
Decode a barcode.
(as configured)
Green
Hands-free Mode
(Presentation Mode On).
None
Green (stays on)
Handheld Mode
(Presentation Mode Off).
None
Green (stays off)
Transmission error.
4 Low beeps
Red
Conversion or format error.
5 Low beeps
Red
RS-232 receive error (Parity Error). Low, Low, Low, Extra-Low beeps
Red
A <BEL> character is received
over RS-232.
None
High beep
Parameter Programming
Input error: Incorrect barcode,
programming sequence, or Cancel Low, High beeps
scanned.
Red
Number expected. Enter value
using numeric barcodes.
High, Low beeps
Green
Successful program exit with
change in parameter setting.
High, Low, High, Low beeps
Green
Enter Bootloader
High, High beeps
Red (stays on)
Firmware Installation
None
Red Blinking
Maintenance Indications
HS-360X Handheld DPM Scanner User Manual
2-7
HS-360X Scanning
HS-360X Scanning
1. Aim the scanner at a barcode and pull the trigger to decode. The aiming laser’s red
dot should fall roughly in the center of the symbol as shown in the image below.
2. Pull the trigger until the scanner beeps, indicating the barcode is successfully decoded.
HS-360X Scanning a Data Matrix
Symbol in Handheld Mode
2-8
HS-360X Handheld DPM Scanner User Manual
Data Capture
HS-360X Wired Scanner Hands-Free Mode
The HS-360X scanner is in Hands-free (presentation) mode when it is placed in the HS-360X
Stand. In this mode, the scanner operates in continuous (constant-on) mode, where it
automatically decodes a barcode presented in its field of view.
When the scanner is not used for a user-definable period of time, it enters a low power mode
in which the LEDs are turned off or illumination blinks at a low duty cycle until the scanner
detects an image change (e.g. motion).
Scanning in Hands-Free (Presentation) Mode
The optional stand adds greater flexibility to HS-360X scanning operation. When the scanner
is seated in the scanner cup, the scanner’s built-in sensor places the scanner in hands-free
(presentation) mode. When the scanner is removed from the stand, it automatically switches to
its programmed handheld triggered mode.
To operate the scanner in the HS-360X Stand:
1. Connect the scanner to the host (see the appropriate host chapter for information on
host connections).
Scanner Cup
Angle Adjustment
Scanner Cup
HS-360X Stand
Height Adjustment
HS-360X Wired Scanner in Hands-Free Mode
2. Insert the scanner in the HS-360X Stand by placing the front of the scanner into the
scanner cup.
3. Use the HS-360X Stand’s adjustment knobs to adjust the height and angle of the scanner.
4. Center the symbol in the aiming pattern.
5. Upon successful decode, the scanner beeps and the LED turns green.
HS-360X Handheld DPM Scanner User Manual
2-9
HS-360X Scanning
Aiming with the HS-360X
When scanning, the HS-360X projects a red laser aiming dot which allows you to position
the symbol within the scanner’s field of view.
HS-360X Scanner
Aiming Pattern
The scanner beeps to indicate that it successfully decoded the symbol.
HS-360X Read Ranges
Symbology
Code 39
Resolution
Inside Edge
Outside Edge
3.0 mil
0.2 in. (0.5 cm)
2.8 in. (7.1 cm)
5.0 mil
0.2 in. (0.5 cm)
2.8 in. (7.1 cm)
PDF417
6.6 mil
0.2 in. (0.5 cm)*
3.2 in. (8.1 cm)
5.0 mil
0.4 in. (1.0 cm)
2.5 in. (6.3 cm)
Data Matrix
10.0 mil
0.0 in. (0.0 cm)
3.4 in. (8.6 cm)
5.0 mil
0.4 in. (1.0 cm)
2.5 in. (6.3 cm)
QR Code
10.0 mil
0.0 in. (0.0 cm)
3.4 in. (8.6 cm)
UPC
13.0 mil
1.0 in. (2.5 cm)*
5.8 in. (14.7 cm)
*Field of view and barcode width limited. Read ranges measured with Decoder Effort Level 1.
Barcodes printed on photographic paper. 30 foot-candles ambient light conditions during testing.
2-10
HS-360X Handheld DPM Scanner User Manual
3 Maintenance and
Technical Specifications
This section describes recommended scanner maintenance, troubleshooting, technical
specifications, and pin assignments.
HS-360X Handheld DPM Scanner User Manual
3-1
Maintenance
Maintenance
Known Harmful Ingredients
The following chemicals are known to damage the plastics on Omron Microscan products
and should not come in contact with the device:
• Acetone
• Ammonia solutions
• Aqueous or alcoholic alkaline solutions
• Aromatic and chlorinated hydrocarbons
• Benzene
• Bleach
• Carbolic acid
• Compounds of amines or ammonia
• Ethanolamine
• Ethers
• Ketones
• TB-lysoform
• Toluene
• Trichloroethylene
Approved Cleaning Agents
The following cleaning agents are approved for cleaning Omron Microscan products:
• Pre-moistened wipes
• Isopropyl alcohol 70%
3-2
HS-360X Handheld DPM Scanner User Manual
Maintenance and Technical Specifications
Tolerable Industrial Fluids and Chemicals
Not all fluid variants and brands have been tested.
The following industrial fluids and chemicals were evaluated and deemed tolerable for the
HS-360X:
• Motor/Engine Oil
• Automatic Transmission Fluid (ATF)
• Continuously Variable Transmission Fluid (CVT)
• Industrial De-Greaser (Engine Brite Heavy Duty)
• Brake Fluid (DOT4)
If the scanner comes in contact with the above fluids and chemicals frequently, Omron
Microscan recommended that you clean the outside of the scanner daily using the
approved cleaning agents listed on the previous page.
Cleaning the Scanner
Routinely cleaning the exit window is required. A dirty window may affect scanning accuracy.
Do not allow any abrasive material to touch the window.
To clean the scanner:
1. Dampen a soft cloth with one of the approved cleaning agents listed above or use
pre-moistened wipes.
2. Gently wipe all surfaces, including the front, back, sides, top and bottom. Never
apply liquid directly to the scanner. Be careful not to let liquid pool around the scanner
window, trigger, cable connector or any other area on the device.
3. Be sure to clean the trigger and in between the trigger and the housing (use a cotton-tipped
applicator to reach tight or inaccessible areas).
4. Do not spray water or other cleaning liquids directly into the exit window.
5. Wipe the scanner exit window with a lens tissue or other material suitable for cleaning
optical material such as eyeglasses.
6. Immediately dry the scanner window after cleaning with a soft non-abrasive cloth to
prevent streaking.
7. Allow the unit to air dry before use.
8. Scanner connectors:
a. Dip the cotton portion of a cotton-tipped applicator in isopropyl alcohol.
b. Rub the cotton portion of the cotton-tipped applicator back-and-forth across the
connector on the Omron Microscan scanner at least 3 times. Do not leave any
cotton residue on the connector.
c. Use the cotton-tipped applicator dipped in alcohol to remove any grease and dirt
near the connector area.
d. Use a dry cotton tipped applicator and rub the cotton portion of the cotton-tipped
applicator back-and-forth across the connectors at least 3 times. Do not leave any
cotton residue on the connectors.
HS-360X Handheld DPM Scanner User Manual
3-3
Troubleshooting
Troubleshooting
Problem
Possible Causes
Possible Solutions
No power to the scanner.
If the configuration requires a
power supply, reconnect the power
supply.
The aiming pattern does not
Incorrect host interface cable is
appear when pressing the trigger. used.
Connect the correct host interface
cable.
Interface/power cables are loose.
Re-connect cables.
Aiming pattern is disabled.
Enable the aiming pattern.
Scanner is not programmed for the Program the scanner to read that
correct barcode type.
type of barcode.
Scanner emits aiming pattern, but
does not decode the barcode.
Barcode symbol is unreadable.
Scan test symbols of the same
barcode type to determine if the
barcode is defaced.
The symbol is not completely
inside aiming pattern.
Move the symbol completely within
the aiming pattern.
Move the symbol completely within
the field of view (AIM pattern does
NOT define FOV)
Distance between scanner and
barcode is incorrect.
Move the scanner closer to or
further from the barcode.
Scan the appropriate host type
Scanner is not programmed for the programming symbol. See the
correct host type.
chapter corresponding to the host
type.
Scanner decodes barcode, but
does not transmit the data to the
host.
Interface cable is loose.
Re-connect the cable.
Cradle is not programmed for the
correct host type.
Check scanner host parameters or
edit options.
Scanner is not paired to host
connected interface.
Pair scanner to the cradle by
scanning the PAIR symbol on the
cradle.
Cradle has lost connection to the
host.
In this exact order: disconnect
power supply; disconnect host
cable; wait three seconds;
reconnect host cable; reconnect
power supply; reestablish pairing.
If the scanner emits 4 long low
beeps, a transmission error
Set the scanner's communication
occurred.
parameters to match the host's
This occurs if a unit is not properly setting.
configured or connected to the
wrong host type.
If the scanner emits 5 low beeps, a
Configure the scanner's
conversion or format error
conversion parameters properly.
occurred.
If the scanner emits low/high/low
beeps, it detected an invalid
scanner rule.
3-4
Program the correct scanner rules.
HS-360X Handheld DPM Scanner User Manual
Maintenance and Technical Specifications
Problem
Possible Causes
Possible Solutions
Scan the appropriate host type
programming symbol.
Host displays scanned data
incorrectly.
Scanner is not programmed to
work with the host.
For RS-232, set the scanner's
communication parameters to
match the host's settings.
Program the proper editing options
(e.g., UPC-E to UPC-A
Conversion).
Scanner emits short low/short
medium/short high beep sequence
(power-up beep sequence) more
than once.
The USB bus may put the scanner
in a state where power to the
Normal during host reset.
scanner is cycled on and off more
than once.
Scanner emits 4 short high beeps Scanner has not completed USB
during decode attempt.
initialization.
Wait several seconds and scan
again.
Scanner emits Low/low/low/extra
low beeps when not in use.
RS-232 receive error.
Normal during host reset.
Otherwise, set the scanner's RS-232
parity to match the host setting.
Scanner emits low/high beeps
during programming.
Input error, incorrect barcode or
Cancel barcode was scanned.
Scan the correct numeric barcodes
within range for the parameter
programmed.
Scanner emits low/high/low/high
beeps during programming.
Out of host parameter storage
space.
Change storage preference.
Scanner emits a power-up beep
after changing USB host type.
The USB bus re-established power Normal when changing USB host
to the scanner.
type.
In RS-232 mode, a <BEL>
Scanner emits one high beep when
character was received and Beep
not in use.
on <BEL> option is enabled.
Scanner emits frequent beeps.
Normal when Beep on <BEL> is
enabled and the scanner is in RS-232
mode.
No power to the scanner.
Check the system power. If the
configuration requires a power
supply, re-connect the power
supply.
Incorrect host interface cable is
used.
Verify that the correct host
interface cable is used. If not,
connect the correct host interface
cable.
Interface/power cables are loose.
Check for loose cable connections
and re-connect cables.
Conversion or format error was
detected.
The scanner’s conversion
parameters are not properly
Scanner emits five long low beeps configured.
after a barcode is decoded.
Conversion or format error was
detected.
A barcode was scanned with
characters that can't be sent for
that host.
Ensure the scanner’s conversion
parameters are properly
configured.
Change the barcode, or change to a
host that can support the barcode.
Note: If the scanner still experiences problems after performing these checks, contact
customer support at www.microscan.com.
HS-360X Handheld DPM Scanner User Manual
3-5
Troubleshooting
Report Software Version Barcode
When contacting support, a support representative may ask you to scan the programming
symbol below to determine the version of software installed in the scanner.
Report Software Version
3-6
HS-360X Handheld DPM Scanner User Manual
Maintenance and Technical Specifications
Technical Specifications
HS-360X Technical Specifications
Item
Description
Physical Characteristics
HS-360X Wireless Scanner Dimensions
7.3 in. H x 3.0 in. W x 5.6 in. D
(18.5 cm H x 7.7 cm W x 14.3 cm D)
HS-360X Wired Scanner Dimensions
7.3 in. H x 3.0 in. W x 5.2 in. D
(18.5 cm H x 7.7 cm W x 13.2 cm D)
HS-360X Wireless Scanner Weight
(with Battery)
Approximately 14.18 oz./402 g
HS-360X Wired Scanner Weight
(without Cable)
Approximately 10.72 oz./304 g
Power
5 VDC +/- 10% @ 360 mA (RMS typical)
Color
Black, red
Performance Characteristics
Light Source
Aiming pattern: 655 nm Laser / Illumination: Warm
white and red 634nm LEDs
Field of View (Horizontal x Vertical) Nominal
31º (H) x 23º (V)
Roll
0 - 360º
Pitch
+/- 60º
Skew
+/- 60º
Scans Per Charge
Up to 100,000
Symbologies
1D
UPC/EAN, UPC/EAN with supplementals, Bookland
EAN, ISSN, UCC Coupon Extended Code, Code
128, GS1-128, ISBT 128, ISBT Concatenation, Code
39, Code 39 Full ASCII, Trioptic Code 39, Code 32,
Code 93, Code 11, Interleaved 2 of 5, Discrete 2 of 5,
Codabar, MSI, Chinese 2 of 5, Matrix 2 of 5, Korean
3 of 5, GS1 DataBar variants
2D
PDF417, MicroPDF417, Composite Codes, TLC-39,
Data Matrix, Maxicode, QR Code, MicroQR, Aztec,
Han Xin, GS1-QR, GS1-DM
Postal
US Postnet, US Planet, UK Postal, Japan Post,
Australia Post, Royal Mail 4 State Customer, KIX
Code (Dutch), UPU 4 State Postal FICS (Post US4),
USPS 4 State Postal (Post US3)
Typical Working Distance
See HS-360X Decode Ranges.
Interfaces Supported
USB, RS-232
The scanner supports the following protocols over
USB: HID Keyboard (default mode), SNAPI, COM
Port Emulation, USB CDC
HS-360X Handheld DPM Scanner User Manual
3-7
Technical Specifications
Item
Description
Code 39: 3 mil
Minimum Resolution
PDF417: 4 mil
Data Matrix: 4 mil
User Environment
HS-360X Wireless Scanner Operating Temperature - 4° F to 122° F (-20° C to 50° C)
HS-360X Wired Scanner Operating Temperature
- 22° F to 122° F (-30° C to 50° C)
Storage Temperature
- 40º F to 158º F (-40º C to 70º C)
Humidity
5% to 95% RH, non-condensing
ESD
20 kV air discharge; 10 kV contact discharge
HS-360X Wireless Scanner Drop Specifications
Withstands multiple 8 ft. / 2.4 m drops to concrete at
room temperature.
HS-360X Wired Scanner Drop Specifications
Withstands multiple 6.5 ft. / 2.0 m drops to concrete
at -30° C to 50° C.
Environmental Sealing
Ambient Light Immunity
IP65 and IP67
0 to 10,037 Foot-Candles
0 to 108,000 Lux
Accessories
HS-360X Wired Scanner Hands-Free Option
HS-360X Stand
Power Supplies
Power supplies are available for applications that do
not supply power over the host cable.
3-8
HS-360X Handheld DPM Scanner User Manual
Maintenance and Technical Specifications
Cradle Technical Specifications
Item
Description
Power Requirements for Host-Powered
Min 4.5 - Max 5.5
Power Requirements for External Power Supply
Min 11.4 - Max 12.6
Typical Current Draw when Not Charging
80mA @ 5V; 30mA @ 12V
Typical Current Draw in Full Charging Mode
1200mA @ 5V (BC 1.2), 475mA (non-BC1.2);
700mA @ 12V
Typical Current Draw in Safe Charging Mode
400mA @ 5V; 200mA @ 12V
Interfaces Supported
USB, RS-232
Operating Temperature
-4° to 122° F (-20° to 50° C)
Storage Temperature
-40° to 158° F (-40° to 70° C)
Charging Temperature
32° to 104° F (0° to 40° C) nominal, 41° to 95° F (5°
to 35° C) ideal
Humidity
5% to 95% (non-condensing)
ESD
25 kV air discharge
10 kV contact discharge
Weight
13.7 oz (390 grams)
Dimensions
W 9.98 x L 22.94 x H 8.26 cm (W 99.8 x L 229.4 x H
82.6 mm)
Radio
Bluetooth, Up to 100 meters/300 ft. in open air
range/environment
Serial Port & HID Profiles
2.402 to 2.480 GHz Adaptive Frequency Hopping
(co-existence with 802.11 wireless networks)
3Mbit/s (2.1Mbit/s) for Classic Bluetooth
1Mbit/s (0.27Mbit/s) for Low Energy
Electrical Safety
Certified to UL/IEC/EN 60950-1 + AM2
Input Transient Protection
IEC 1000-4-(2,3,4,5,6,11)
EMI
FCC Part 15 Class B, ICES-003 Class B European
Union EMC Directive, Australian SMA, Taiwan EMC,
Japan VCCI Class B
HS-360X Handheld DPM Scanner User Manual
3-9
HS-360X Wired Scanner Signal Descriptions
HS-360X Wired Scanner Signal Descriptions
Base of Scanner Handle
Cable Interface Port
Pin 1
Pin 10
Interface Cable
Modular Connector
HS-360X Wired Scanner Cable Pinouts
The signal descriptions below apply to the connectors on the HS-360X Wired Scanner and
are for reference only.
Pin
RS-232
1
Cable ID
Cable ID
2
Power (+5V)
Power (+5V)
3
Ground
Ground
4
TxD
Reserved
5
RxD
D+
6
RTS
Reserved
7
CTS
D-
8
Reserved
Reserved
9
Reserved
Reserved
10
Power (+12V)
Power (+12V)
3-10
USB
HS-360X Handheld DPM Scanner User Manual
4 Radio Communications
This section provides information about the modes of operation and features available for
wireless communication between HS-360X Wireless Scanners, cradles, and hosts. This
section also includes scanner configuration parameters.
HS-360X Handheld DPM Scanner User Manual
4-1
HS-360X Wireless Scanner Radio Communications
HS-360X Wireless Scanner Radio Communications
The scanner ships with the settings shown in the Radio Communications Parameter
Defaults. If the default values suit requirements, programming is not necessary.
To set feature values, scan a single programming symbol or a short sequence of programming
symbols. The settings are stored in non-volatile memory and are preserved even when the
scanner is powered down.
If not using a USB cable with the cradle, select a host type (see each host chapter for specific
host information) after the power-up beep. This is only necessary upon the first power-up
when connected to a new host.
Scanning Sequence Examples
In most cases, scan one programming symbol to set a specific parameter value.
Errors While Scanning
Unless otherwise specified, to correct an error during a scanning sequence, just re-scan the
correct parameter.
4-2
HS-360X Handheld DPM Scanner User Manual
Radio Communications
Radio Communications Parameter Defaults
The table below lists the defaults for radio communication parameters. If you wish to change
any option, scan the appropriate programming symbol(s) provided in the Radio Communications
Parameters section.
See Appendix A — Standard Default Parameters for all user preferences, hosts, symbologies,
and default parameters.
In this guide, the parameter numbers listed are the same as the attribute numbers for these
parameters.
See Appendix B — Country Codes for Country Keyboard Types (Country Codes).
Parameter
Parameter Number1
Default
Radio Communications Host
Types
383
Cradle Host
BT Friendly Name
607
n/a
Discoverable Mode
610
General
Wi-Fi Friendly Mode
1299
Disable
Wi-Fi Friendly Channel Exclusion
1297
Use All Channels
Radio Output Power
1324
High
Link Supervision Timeout
1698
5 Seconds
Bluetooth Radio State
1354
On
Bluetooth HID - Wait for
Connection
1714
Disable
HID Features for Apple iOS
1114
Disable
HID Keyboard Keystroke Delay
N/A
No Delay (0 msec)
CAPS Lock Override
N/A
Disable
Ignore Unknown Characters
N/A
Send Barcodes with Unknown
Characters
Emulate Keypad
N/A
Enable
Fast HID Keyboard
1361
Enable
Quick Keypad Emulation
1362
Enable
Keyboard FN1 Substitution
N/A
Disable
Function Key Mapping
N/A
Disable
Simulated Caps Lock
N/A
Disable
Convert Case
N/A
No Case Conversion
Reconnect Attempt Beep
Feedback
559
Disable
Reconnect Attempt Interval
558
30 Seconds
Auto-reconnect
604
Auto-reconnect Immediately
Beep on Insertion
288
Enable
1. Parameter number decimal values are used for programming via RSM commands.
HS-360X Handheld DPM Scanner User Manual
4-3
Radio Communications Parameter Defaults
Parameter
Parameter Number1
Default
Beep on <BEL>
150
Enable
Modes of Operation
538
(Point-to-Point/Multipoint-to-Point)
Point-to-Point
Parameter Broadcast (Cradle Host
148
Only)
Enable
Pairing Modes
542
Unlocked
Pairing Methods
545
Enable
Disable
Toggle Pairing
1322
Connection Maintenance Interval
5002
15 Minutes
Batch Mode
544
Normal (Do Not Batch Data)
Persistent Batch Storage
1399
Disable
Page Button
746
Enable
Page Options
Page Mode
Page State Timeout
1364
1365
Page Simple
Classic and/or Low Energy
Bluetooth
1355
Classic and Low Energy
PIN Code (Set and Store)
552
12345
Variable Pin Code
608
Static
(Default PIN code is 12345)
Bluetooth Security Levels
1393
Low
1. Parameter number decimal values are used for programming via RSM commands.
4-4
HS-360X Handheld DPM Scanner User Manual
Radio Communications
Wireless Beeper Definitions
When the scanner decodes the pairing symbol it issues various beep sequences indicating
successful or unsuccessful operations.
Radio Communications Host Types
Parameter # 383
To set up the scanner for communication with a cradle, or to use standard Bluetooth profiles,
scan the appropriate host type programming symbol below.
Classic Bluetooth vs. Low Energy Bluetooth
Bluetooth Low Energy (LE) Bluetooth has a better Wi-Fi coexistence, as advertising and
connection is done outside of the Wi-Fi channels 1, 6, and 11 (2402, 2426, 2480 MHz). Due
to its lower data rate, Bluetooth Low Energy is up to seven times slower than Classic Bluetooth
(0.27 Mbps versus 0.7-2.1 Mbps). Data intensive activities such as firmware updates, can
take significantly longer over Bluetooth Low Energy.
Cradle
Select this host type when connecting a scanner to a communication cradle.
The scanner automatically tries to reconnect to a remote device when a disconnection
occurs that is due to the radio losing communication.
To establish a connection (for initial setup only):
1. Scan the Cradle-Classic Bluetooth or Cradle-Low Energy programming symbol.
2. Scan the pairing symbol on the cradle or place the scanner in the cradle.
Cradle-Classic
Cradle-Low Energy
HS-360X Handheld DPM Scanner User Manual
4-5
Radio Communications Host Types
Keyboard Emulation (HID)
Select this host type when connecting to a PC/tablet/phone emulating a Bluetooth keyboard.
• HID BT Classic - Enables the host and scanner to communicate using HID (Human
Interface Device) Keyboard Profile over Bluetooth Classic radio. The scanner(s) are
discoverable (Secondary mode) and also support Primary (Master) mode.
To establish a connection (initial setup only):
i. Scan the HID BT Classic programming symbol.
ii. Connect to Primary or Secondary mode.
• Primary mode - scan a pairing symbol with the MAC address of the host
device.
• Secondary mode - from the host, discover Bluetooth devices and select your
scanner from the discovered device list.
• HID BT LE (Discoverable) - Enables the host to establish a HID (Human Interface
Device) Keyboard Profile connection with the scanner over Bluetooth Low Energy radio.
The scanner is discoverable (Secondary mode).
To establish a connection (initial setup only):
i. Scan the HID BT LE (Discoverable) programming symbol.
ii. From the host, discover Bluetooth devices.
iii. Select your scanner from your discovered device list.
HID Bluetooth Classic
HID BT LE (Discoverable)
4-6
HS-360X Handheld DPM Scanner User Manual
Radio Communications
Serial Port Profile (SPP)
Select this host type when connecting to a PC/tablet/phone using a Bluetooth serial connection.
• SPP BT Classic (Non-Discoverable) - Enables the scanner to establish a Serial Port
Profile (SPP) connection with the host over Classic Bluetooth radio. The scanner is NOT
discoverable (Primary mode).
To establish a connection (initial setup only):
i. Scan the SPP BT Classic (Non-discoverable) programming symbol.
ii. Scan a pairing symbol with the MAC address of the host device.
• SPP BT Classic (Discoverable) - Enables the host to establish a Serial Port Profile
(SPP) connection with the scanner over Classic Bluetooth radio. The scanner is discoverable
(Secondary mode).
To establish a connection (initial setup only):
i. Scan the SPP BT Classic (Discoverable) programming symbol.
ii. From the host, discover Bluetooth devices.
iii. Select your scanner from the discovered device list.
SPP BT Classic (Non-Discoverable)
SPP BT Classic (Discoverable)
HS-360X Handheld DPM Scanner User Manual
4-7
Radio Communications Host Types
Bluetooth Technology Profile Support
With Bluetooth Technology Profile Support, the cradle is not required for wireless communication.
The scanner communicates directly to the host using Bluetooth technology. The scanner
supports the standard Bluetooth Serial Port Profile (SPP) and HID Profiles which enable the
scanner to communicate with other Bluetooth devices that support these profiles.
• SPP - the scanner connects to the PC/host via Bluetooth and performs like there is a
serial connection.
• HID - the scanner connects to the PC/host via Bluetooth and performs like a keyboard.
Primary/Secondary Set Up
The scanner can be set up as a Primary or Secondary. When the scanner is set up as a
Secondary, it is discoverable and connectible to other devices. When the scanner is set up
as a Primary, the Bluetooth address of the remote device to which a connection is requested
is required. A pairing symbol with the remote device address must be created and scanned
to attempt a connection to the remote device.
Primary
When the scanner is set up as a Primary (SPP), it initiates the radio connection to a secondary
device. Initiating the connection is done by scanning a pairing symbol for the remote device.
Secondary
When the scanner is set up as a Secondary device (SPP), the scanner accepts an incoming
connection request from a remote device. The number of scanners is dependent on the
host’s capability.
4-8
HS-360X Handheld DPM Scanner User Manual
Radio Communications
Bluetooth-Friendly Name
Parameter # 607
You can set a meaningful name for the scanner that appears in the application during device
discovery. The default name is the scanner name followed by its serial number, e.g., HS-360X
123456789ABCDEF. Scanning Set Defaults reverts the scanner to this name; use custom
defaults to maintain the user-programmed name through a Set Defaults operation.
To set a new Bluetooth Friendly Name, scan the following programming symbol, then scan
up to 23 characters from Appendix G — Alphanumeric Keyboard.
Bluetooth Friendly Name
HS-360X Handheld DPM Scanner User Manual
4-9
Bluetooth-Friendly Name
Discoverable Mode
Parameter # 610
Select a discoverable mode based on the device initiating discovery:
• Select General Discoverable Mode when initiating connection from a PC.
• Select Limited Discoverable Mode when initiating connection from a mobile device
(e.g., iPhone), and the device does not appear in General Discoverable Mode. Note that
it can take longer to discover the device in this mode.
The device remains in Limited Discoverable Mode for 30 seconds, and green LEDs flash
while in this mode. It is then non-discoverable. To re-active Limited Discoverable Mode,
press the trigger.
* General Discoverable Mode
(0)
Limited Discoverable Mode
(1)
4-10
HS-360X Handheld DPM Scanner User Manual
Radio Communications
Wi-Fi Friendly Mode
Parameter # 1299
Scanners configured for Wi-Fi friendly mode behave as follows:
• The scanner remains in sniff mode, and exits sniff mode only during firmware update.
• If any Wi-Fi channel is excluded from the hopping sequence, AFH turns off.
• Scanner (and cradle) avoid the selected Wi-Fi channels after establishing connection.
Notes
• If using this feature, configure all scanners in the area for Wi-Fi friendly mode.
• By default, no Wi-Fi channels are excluded.
• Since Bluetooth requires a minimum of 20 channels when Wi-Fi channels 1, 6, and 11
are excluded,
a smaller number of channels are cut from the hopping sequence.
• Updating Wi-Fi friendly settings before Bluetooth connection is recommended.
Scan a programming symbol below to enable or disable Wi-Fi Friendly Mode.
* Disable Wi-Fi Friendly Mode
(0)
Enable Wi-Fi Friendly Mode
(1)
HS-360X Handheld DPM Scanner User Manual
4-11
Wi-Fi Friendly Mode
Wi-Fi Friendly Channel Exclusion
Parameter # 1297
WiFi Channel Exclusion
Select the channels to exclude:
• Exclude Wi-Fi channel 1: Bluetooth channels 0-21 are excluded from hopping sequence
(2402-2423 MHz).
• Exclude Wi-Fi channel 6: Bluetooth channels 25-46 are excluded from hopping
sequence (2427 - 2448 MHz).
• Exclude Wi-Fi channel 11: Bluetooth channels 50-71 are excluded from hopping
sequence (2452 - 2473 MHz).
• Exclude Wi-Fi channel 1, 6 and 11: Bluetooth channels 2-19 (2404-2421 MHz),
26-45 (2428 - 2447 MHz) and 51-69 (2453 - 2471 MHz) are excluded from hopping sequence.
• Exclude Wi-Fi channels 1 and 6: Bluetooth channels 0-21 (2402-2423 MHz) and 25-46
(2427 - 2448 MHz) are excluded from hopping sequence.
• Exclude Wi-Fi channels 1 and 11: Bluetooth channels 0-21 (2402-2423 MHz) and 50-71
(2452 - 2473 MHz) are excluded from hopping sequence.
• Exclude Wi-Fi channel 6 and 11: Bluetooth channels 25-46 (2427 - 2448 MHz) and 50-71
(2452 - 2473 MHz) are excluded from hopping sequence.
* Use All Channels (Standard)
(0)
Exclude Wi-Fi Channel 1
(1)
Exclude Wi-Fi Channel 6
(2)
4-12
HS-360X Handheld DPM Scanner User Manual
Radio Communications
Exclude Wi-Fi Channel 11
(3)
Exclude Wi-Fi Channels 1, 6, and 11
(4)
Exclude Wi-Fi Channels 1 and 6
(5)
Exclude Wi-Fi Channels 1 and 11
(6)
Exclude Wi-Fi Channels 6 and 11
(7)
HS-360X Handheld DPM Scanner User Manual
4-13
Radio Output Power
Radio Output Power
Parameter # 1324
The HS-360X Wireless Scanner uses a Class 1 Bluetooth radio. Optionally, reduce the
radio’s output power to restrict the transmission range and reduce the effect of the radio on
neighboring wireless systems.
Bluetooth stack resets on power change and the device loses connection.
Scan a programming symbol to select the desired power mode.
* High Power Setting
(0)
Medium Power Setting
(1)
Low Power Setting
(2)
4-14
HS-360X Handheld DPM Scanner User Manual
Radio Communications
Link Supervision Timeout
Parameter # 1698
Link supervision timeout controls how quickly the scanner senses that the Bluetooth radio
lost connection to the remote device. A lower value helps prevent data loss at the edge of
the operating range while a larger value helps prevent disconnects due to the remote device
not responding in time. If you are experiencing occasional disconnects and the scanner is
able to reconnect, increase the link supervision timeout value.
.5 Seconds
2 Seconds
5 Seconds
10 Seconds
20 Seconds
HS-360X Handheld DPM Scanner User Manual
4-15
Bluetooth Radio State
Bluetooth Radio State
Parameter # 1354
The only option to turn the radio on after it is turned off on the cradle, is through the host.
Bluetooth Radio Off
(0)
* Bluetooth Radio On
(1)
4-16
HS-360X Handheld DPM Scanner User Manual
Radio Communications
HID Host Parameters
The scanner supports virtual keyboard emulation for the Apple iOS, and keyboard emulation
over the Bluetooth HID profile. In this mode the scanner can interact with Bluetooth enabled
hosts supporting the HID profile as a Bluetooth keyboard. Scanned data is transmitted to the
host as keystrokes.
Bluetooth HID - Wait for Connection
Parameter # 1714
This setting applies to first time connection only, when scanner connects to remote device
by scanning a paring symbol.
When disabled, the scanner issues a connection after scanning a pairing symbol. This is the
recommended setting for Android devices.
When enabled, the scanner waits for a connection request from a remote device, after scanning
a pairing symbol and initiating pairing. This is the recommended setting for Windows devices
and VC80.
* Disable
(0)
Enable
(1)
HS-360X Handheld DPM Scanner User Manual
4-17
HID Host Parameters
HID Features for Apple iOS
Parameter # 1114
This option works with Apple iOS devices to enable the opening and closing of the iOS virtual
keyboard by double-pressing the trigger.
When this feature is enabled, the scanner may be incompatible with non-Apple iOS devices.
* Disable
(0)
Enable
(1)
4-18
HS-360X Handheld DPM Scanner User Manual
Radio Communications
HID Keyboard Keystroke Delay
This parameter sets the delay, in milliseconds (msec), between emulated keystrokes. Scan a
programming symbol below to increase the delay when the HID host requires a slower
transmission of data.
* No Delay (0 msec)
Medium Delay (20 msec)
Long Delay (40 msec)
HS-360X Handheld DPM Scanner User Manual
4-19
HID Host Parameters
HID Caps Lock Override
When enabled, the case of the data is preserved regardless of the state of the caps lock key.
This setting is always enabled for the Japanese, Windows (ASCII) keyboard type and can
not be disabled.
* Do Not Override Caps Lock Key
(Disable)
Override Caps Lock Key
(Enable)
4-20
HS-360X Handheld DPM Scanner User Manual
Radio Communications
HID Ignore Unknown Characters
This option applies only to the HID Keyboard Emulation device and IBM device. Unknown
characters are characters the host does not recognize. When Send Barcodes With
Unknown Characters is selected, all barcode data is sent except for unknown characters,
and no error beeps sound. When Do Not Send Barcodes With Unknown Characters is
selected, barcode data is sent up to the first unknown character, then the scanner issues an
error beep.
* Send Barcodes With Unknown
Characters
(Enable)
Do Not Send Barcodes With Unknown
Characters
(Disable)
HS-360X Handheld DPM Scanner User Manual
4-21
HID Host Parameters
Emulate Keypad
When enabled, all characters are sent as ASCII sequences over the numeric keypad. For
example, ASCII A is sent as "ALT make" 0 6 5 "ALT Break".
Disable Keypad Emulation
* Enable Keypad Emulation
4-22
HS-360X Handheld DPM Scanner User Manual
Radio Communications
Fast HID Keyboard
Parameter # 1361
This option transmits Bluetooth HID keyboard data at a faster rate.
Fast HID Disable
(0)
* Fast HID Enable
(1)
HS-360X Handheld DPM Scanner User Manual
4-23
HID Host Parameters
Quick Keypad Emulation
Parameter # 1362
This option applies only to a HID Keyboard Emulation Device which has Emulate Keypad
enabled.
This parameter enables a quicker method of keypad emulation where ASCII sequences are
only sent for ASCII characters not found on the keyboard.
Quick Keypad Emulation Disable
(0)
* Quick Keypad Emulation Enable
(1)
4-24
HS-360X Handheld DPM Scanner User Manual
Radio Communications
HID Keyboard FN1 Substitution
When enabled, this parameter allows replacement of any FN1 character in an EAN128 barcode
with a Key Category and value chosen by the user.
* Disable Keyboard FN1 Substitution
Enable Keyboard FN1 Substitution
HS-360X Handheld DPM Scanner User Manual
4-25
HID Host Parameters
HID Function Key Mapping
ASCII values under 32 are normally sent as control-key sequences. When this parameter is
enabled, the keys in bold are sent in place of the standard key mapping.
Table entries that do not have a bold entry remain the same whether or not this parameter is
enabled.
* Disable Function Key Mapping
Enable Function Key Mapping
4-26
HS-360X Handheld DPM Scanner User Manual
Radio Communications
Simulated Caps Lock
When enabled, the scanner inverts upper and lower case characters on the barcode as if the
Caps Lock state is enabled on the keyboard. This inversion is done regardless of the current
state of the keyboard Caps Lock state.
* Disable Simulated Caps Lock
Enable Simulated Caps Lock
HS-360X Handheld DPM Scanner User Manual
4-27
HID Host Parameters
Convert Case
When enabled, the scanner converts all barcode data to the selected case.
* No Case Conversion
Convert All to Upper Case
Convert All to LowerCase
4-28
HS-360X Handheld DPM Scanner User Manual
Radio Communications
Reconnect Attempt Beep Feedback
When in SPP Primary, Cradle Host Mode, and Bluetooth Keyboard Emulation, the scanner
automatically tries to reconnect to a remote device when a disconnection occurs that is due
to the radio losing communication. This can happen if the scanner goes out of range with the
remote device, or if the remote device powers down. The scanner tries to reconnect for the
period of time specified by the Reconnect Attempt Interval setting. During that time the
green LED continues to blink.
If the auto-reconnect process fails due to page time-outs, the scanner sounds a page timeout
beep (long low/long high) and enters low power mode. The auto-reconnect process can be
re-started by pulling the scanner trigger.
If the auto-reconnect process fails because the remote device rejects the connection
attempt, the scanner sounds a connection reject beep sequence and deletes the remote
pairing address. If this happens, a pairing symbol must be scanned to attempt a new connection
to the remote device.
If a barcode is scanned while the auto-reconnect sequence is in process, a transmission
error beep sequence sounds and the data is not transmitted to the host. After a connection
is reestablished, normal scanning operation returns.
The scanner has memory available for storing a remote Bluetooth address for each Primary
mode (SPP, Cradle). When switching between these modes, the scanner automatically tries
to reconnect to the last device it was connected to in that mode.
Switching between Bluetooth host types by scanning a host type programming symbol
causes the radio to be reset. Scanning is disabled during this time. It takes several seconds
for the scanner to re-initialize the radio at which time scanning is enabled.
HS-360X Handheld DPM Scanner User Manual
4-29
Reconnect Attempt Beep Feedback
Reconnect Attempt Beep Feedback
Parameter # 559
When a scanner disconnects as it goes out of range, it immediately attempts to reconnect.
While the scanner attempts to reconnect, the green LED continues to blink. If the auto-reconnect
process fails, the scanner emits a page timeout beep (long low/long high) and stops blinking
the LED. The process can be restarted by pulling the trigger.
The Beep on Reconnect Attempt feature is disabled by default. When enabled, the scanner
emits 5 short high beeps every 5 seconds while the re-connection attempt is in progress.
Scan a programming symbol below to enable or disable Beep on Reconnect Attempt.
* Disable Beep on Reconnect Attempt
(0)
Enable Beep on Reconnect Attempt
(1)
4-30
HS-360X Handheld DPM Scanner User Manual
Radio Communications
Reconnect Attempt Interval
Parameter # 558
When a scanner disconnects as it goes out of range, it immediately attempts to reconnect
for the default time interval of 30 seconds. This time interval can be changed to one of the
options below.
To set the Reconnect Attempt Interval, scan one of the programming symbols below.
* Attempt to Reconnect for 30 Seconds
(6)
Attempt to Reconnect for 1 Minute
(12)
Attempt to Reconnect for 5 Minutes
(60)
Attempt to Reconnect for 30 Minutes
(360)
HS-360X Handheld DPM Scanner User Manual
4-31
Reconnect Attempt Beep Feedback
Attempt to Reconnect for 1 Hour
(720)
Attempt to Reconnect Indefinitely
(0)
4-32
HS-360X Handheld DPM Scanner User Manual
Radio Communications
Auto-Reconnect
Parameter # 604
In Bluetooth Keyboard Emulation (HID) mode, SPP Primary, and Cradle Host Mode, select a
re-connect option for when the scanner loses its connection with a remote device:
• Auto-reconnect on Barcode Data: The scanner auto-reconnects when you scan a
barcode. With this option, a delay can occur when transmitting the first characters. The
scanner sounds a decode beep upon barcode scan, followed by a connection, a page
timeout, a rejection beep, or a transmission error beep. Select this option to optimize
battery life on the scanner and mobile device. Note that auto-reconnect does not occur
on rejection and cable unplug commands.
• Auto-reconnect Immediately: When the scanner loses connection, it attempts to
reconnect. If a page timeout occurs, the scanner attempts reconnect on a trigger pull.
Select this option if the scanner’s battery life is not an issue and you do not want a delay
to occur when the first barcode is transmitted. Note that auto-reconnect does not occur
on rejection and cable unplug commands.
• Disable Auto-reconnect: When the scanner loses connection, you must re-establish it
manually.
Auto-Reconnect on Barcode Data
(1)
* Auto-Reconnect Immediately
(2)
Disable Auto-Reconnect
(0)
HS-360X Handheld DPM Scanner User Manual
4-33
Out-of-Range Indicator
Out-of-Range Indicator
An out-of-range indicator can be set by scanning Beep On Reconnect Attempt and extending
the time using the Reconnect Attempt Interval.
For example, with Beep on Reconnect Attempt disabled while the scanner loses radio
connection when it is taken out of range, the scanner attempts to reconnect silently during
the time interval set by scanning a Reconnect Attempt Interval.
When Beep on Reconnect Attempt is enabled, the scanner emits 5 high beeps every 5
seconds while the re-connection attempt is in progress. If the Reconnect Attempt Interval is
adjusted to a longer period of time, such as 30 minutes, the scanner emits 5 high beeps
every 5 seconds for 30 minutes providing an out-of-range indicator.
4-34
HS-360X Handheld DPM Scanner User Manual
Radio Communications
Beep on Insertion
Parameter # 288
When a scanner is inserted into a cradle and detects power, it emits a short low beep. This
feature is enabled by default.
To enable or disable beeping on insertion, scan the appropriate programming symbol below.
* Enable Beep on Insertion
(1)
Disable Beep on Insertion
(0)
HS-360X Handheld DPM Scanner User Manual
4-35
Beep on <BEL>
Beep on <BEL>
Parameter # 150
When this parameter is enabled, the scanner issues a beep when a <BEL> character is
detected on the serial line. <BEL> is issued to gain a user's attention to an illegal entry or
other important events.
This parameter only applies to SPP (Serial Port Profile). The RS-232 interface on the cradle
has this feature when Beep on <BEL> is enabled.
In Multipoint-to-Point mode only, the scanner that beeped last sounds Beep on <BEL>.
* Beep on <BEL> Enable
(1)
Beep on <BEL> Disable
(0)
4-36
HS-360X Handheld DPM Scanner User Manual
Radio Communications
Scanner(s)-to-Cradle Support
Modes of Operation
Parameter # 538
The charging cradle with radio supports two radio communication modes of operation, allowing
the scanner to communicate wirelessly:
• Point-to-Point
• Multipoint-to-Point
Point-to-Point Communication
In Point-to-Point communication mode, the cradle allows one scanner to connect to it at a
time. In this mode, the scanner is paired to the cradle either by insertion into the cradle or by
scanning the PAIR symbol. Communication can be locked, unlocked (default), or in a lock
override state. In locked mode, locking intervals must be set by scanning a connection
maintenance interval programming symbol.
To activate this mode of operation, scan Point-to-Point.
Multipoint-to-Point Communication
Multipoint-to-Point communication mode allows up to seven scanners to pair to one cradle.
To activate this mode, the first scanner connected to the cradle must scan the Multipoint-to-Point
programming symbol. This mode allows a parameter broadcast feature that forwards
parameter programming symbol settings to all connected scanners. In this mode, programming
one scanner applies the settings to all connected scanners.
To select Point-to-Point or Multipoint-to-Point mode, scan the appropriate programming symbol.
Note: WeblinkPC is not supported when scanners are in Multipoint-to-Point pairing mode.
Setup is only supported in Point-to-Point pairing.
Multipoint-to-Point Mode
(1)
* Point-to-Point Mode
(0)
HS-360X Handheld DPM Scanner User Manual
4-37
Scanner(s)-to-Cradle Support
Parameter Broadcast (Cradle Host Only)
Parameter # 148
When Parameter Broadcast is disabled on one scanner in the piconet, Parameter Broadcast
is disabled on all scanners in the piconet.
When in multipoint-to-point mode, enable Parameter Broadcast to broadcast all parameter
programming symbols scanned to all other scanners in the piconet. If disabled, parameter
programming symbols are processed by the individual scanner only, and the scanner
ignores parameters broadcast from other scanners or from the cradle.
* Enable Parameter Broadcast
(1)
Disable Parameter Broadcast
(0)
4-38
HS-360X Handheld DPM Scanner User Manual
Radio Communications
Pairing
Pairing is the process by which a scanner initiates communication with a cradle. Scanning
Multipoint-to-Point activates multi scanner-to-cradle operation and allows up to seven scanners
to pair to one cradle.
To pair the scanner with the cradle, scan the pairing symbol. A high/low/high/low beep
sequence indicates that the pairing symbol was decoded. When a connection between the
cradle and scanner is established, a low/high beep sounds.
1. The pairing symbol that connects the scanner to a cradle is unique to each cradle.
2. Do not scan data or parameters until pairing completes.
3. Only when the scanner is paired to the cradle, it automatically tries to reconnect to a
remote device when a disconnection occurs that is due to the radio losing communication.
Pairing Modes
Parameter # 542
When operating with the cradle, two modes of pairing are supported:
• Locked Pairing Mode - When a cradle is paired (connected) to the scanner (or up to
seven scanners in Multipoint-to-Point mode), any attempt to connect a different scanner,
by either scanning the PAIR symbol on the cradle or by inserting it into the cradle with
the pairing on contacts feature enabled, is rejected. The currently connected scanner(s)
maintain connection. In this mode, you must set a Connection Maintenance Interval.
• Unlocked Pairing Mode - Unlocking works in Point-to-Point mode only. Pair (connect) a
new scanner to a cradle at any time by either scanning the PAIR symbol on the cradle or
by inserting it into the cradle with the pairing on contacts feature enabled. This unpairs
the previous scanner from the cradle.
To set the cradle pairing mode, scan the appropriate programming symbol below.
* Unlocked Pairing Mode
(0)
Locked Pairing Mode
(1)
HS-360X Handheld DPM Scanner User Manual
4-39
Scanner(s)-to-Cradle Support
Lock Override
Lock Override is applicable in Point-to-Point mode only (does not apply to Multipoint-to-Point
mode). In Multipoint-to-Point mode, if seven scanners are connected, the scanners must be
disconnected for a new scanner to connect.
Lock Override overrides a locked scanner base pairing and connects a new scanner. To use
Lock Override, scan the programming symbol below, followed by the pairing barcode on the cradle.
Lock Override
Pairing Methods
Parameter # 545
There are two pairing methods. The default method allows the scanner and cradle to pair
(connect) when the pairing symbol on the cradle is scanned. A second method pairs the
scanner and cradle when the scanner is inserted in the cradle. To enable this feature, scan
Enable Pair On Contacts below. With this feature enabled it is not necessary to scan the
pairing symbol on the cradle. If the pairing is successful, a low/high connection beep
sequence sounds a few seconds after the scanner is placed in the cradle. To enable or
disable pairing on contacts, scan the appropriate programming symbol below.
* Enable Pair On Contacts
(1)
Disable Pair on Contacts
(0)
4-40
HS-360X Handheld DPM Scanner User Manual
Radio Communications
Unpairing
Unpair the scanner from the cradle or PC/host to make the cradle available for pairing with
another scanner. Scan the programming symbol below to disconnect the scanner from its
cradle/PC host.
An unpairing symbol is also included in the HS-360X Wireless Scanner Quick Start Guide.
Unpairing
Toggle Pairing
Parameter # 1322
If the scanner is configured for Toggle Pairing, scanning the Toggle Pairing symbol a second
time will unpair the scanner.
* Toggle Pairing Disable
(0)
Toggle Pairing Enable
(1)
HS-360X Handheld DPM Scanner User Manual
4-41
Scanner(s)-to-Cradle Support
Pairing Barcode Format
When the scanner is configured as an SPP Primary, you must create a pairing symbol for
the remote Bluetooth device to which the scanner can connect. The Bluetooth address of
the remote device must be known. Pairing symbols are formatted as follows:
<Fnc 3>Bxxxxxxxxxxxx
where:
• B (or LNKB) is the prefix
• xxxxxxxxxxxx represents the 12-character Bluetooth address.
Pairing Barcode Example
If the remote device to which the scanner can connect has a Bluetooth address of
11:22:33:44:55:66, then the pairing symbol is:
Paring Barcode Content:
‘B’ + Bluetooth Address
4-42
B112233445566
HS-360X Handheld DPM Scanner User Manual
Radio Communications
Connection Maintenance Interval
The Connection Maintenance Interval only applies in locked pairing mode.
When a scanner disconnects from a cradle due to a Link Supervision Timeout, the scanner
immediately attempts to reconnect to the cradle for 30 seconds. If the auto-reconnect process
fails, it can be restarted by pulling the scanner trigger.
To guarantee that a disconnected scanner can reconnect when it comes back in range, the
cradle reserves the connection for that scanner for a period of time defined by the Connection
Maintenance Interval. If the cradle is supporting the maximum three scanners and one
scanner disconnects, a fourth scanner cannot pair to the cradle during this interval. To connect
another scanner: either wait until the connection maintenance interval expires then scan the
PAIR symbol on the cradle with the new scanner; or, scan Lock Override with the new
scanner then scan the PAIR symbol on the cradle.
The cradle stores the remote pairing address of each scanner in memory regardless of the
scanner condition (e.g., discharged battery). When you want to change the scanners paired
to the cradle, unpair each scanner currently connected to the cradle by scanning the
Unpairing symbol prior and reconnect each appropriate scanner by scanning the PAIR
symbol on the cradle.
Considerations
The system administrator determines the Connection Maintenance Interval. A shorter interval
allows new users to gain access to abandoned connections more quickly, but causes
problems if users leave the work area for extended periods. A longer interval allows existing
users to leave the work area for longer periods of time, but ties up the system for new users.
To avoid this conflict, users who are going off-shift can scan the Unpairing symbol to ignore
the Connection Maintenance Interval and make the connection immediately available.
HS-360X Handheld DPM Scanner User Manual
4-43
Scanner(s)-to-Cradle Support
Connection Maintenance Interval (continued)
To set the Connection Maintenance Interval, scan one of the programming symbols below.
* Set Interval to 15 Minutes
(0)
Set Interval to 30 Minutes
(1)
Set Interval to 60 Minutes
(2)
Set Interval to 2 Hours
(3)
4-44
HS-360X Handheld DPM Scanner User Manual
Radio Communications
Connection Maintenance Interval (continued)
Set Interval to 4 Hours
(4)
Set Interval to 8 Hours
(5)
Set Interval to 24 Hours
(6)
Set Interval to Forever
(7)
HS-360X Handheld DPM Scanner User Manual
4-45
Batch Mode
Batch Mode
Parameter # 544
Batch mode does not apply to SPP Secondary Mode.
The scanner supports five versions of batch mode. When the scanner is configured for any
of the batch modes, it attempts to store barcode data (not parameter barcodes) until transmission
is initialized, or the maximum number of barcodes are stored. When a barcode is saved
successfully, a good decode beep sounds and the LED flashes green. If the scanner is
unable to store a new barcode, a low/high/low/high out of memory beep sounds.
In all modes, calculate the amount of data (number of barcodes) the scanner can store as follows:
Number of storable barcodes = 30,720 bytes of memory / (number of characters in the
barcode + 3).
If the batch mode selection is changed while there is batched data, the new batch mode
takes effect only after all the previously batched data is sent.
Modes of Operation
• Normal (default) - Do not batch data. The scanner attempts to transmit every scanned barcode.
• Out of Range Batch Mode - The scanner starts storing barcode data when it loses its
connection to a remote device (for example, when a user holding the scanner walks out
of range). Data transmission is triggered by reestablishing the connection with the
remote device (for example, when a user holding the scanner walks back into range).
• Standard Batch Mode - The scanner starts storing barcode data after Enter Batch
Mode is scanned. Data transmission is triggered by scanning Send Batch Data
Transmission is halted if the connection to the remote device is lost.
• Cradle Contact Batch Mode - The scanner starts storing barcode data when Enter
Batch Mode is scanned. Data transmission is triggered by insertion of the scanner into
the cradle.
If the scanner is removed from the cradle during batch data transfer, transmission halts
until the scanner is re-inserted in the cradle.
• Batch Only Mode - The scanner radio is turned off and the scanner stores all barcode
data. Data transmission is triggered by insertion of the scanner into the cradle.
If the scanner is removed from the cradle during batch data transfer, transmission halts
until the scanner is re-inserted in the cradle.
The radio may be turned off as batch data is transmitted over the cradle contacts.
This mode can only be exited by scanning Normal (default) mode.
• Parameter Batch Mode - When Parameter Batch Mode is entered and no connection
to the cradle exists, the scanner begins storing parameter programming symbol data
intended for the cradle. Parameter transmission is triggered by insertion of the scanner
into the cradle. Parameter Batch Mode is exited upon the end of the transmission.
Alternatively, parameter programming symbol batching my be cancelled prior to insertion
of the scanner into the cradle by scanning Exit Parameter Batch Mode.
Parameter Batch Mode may be used when the cradle and/or scanner is configured
with its radio turned off or connected to a non-cradle device.
4-46
HS-360X Handheld DPM Scanner User Manual
Radio Communications
* Normal
(0)
Out of Range Batch Mode
(1)
Standard Batch Mode
(2)
Cradle Contact Batch Mode
(3)
HS-360X Handheld DPM Scanner User Manual
4-47
Batch Mode
Enter Batch Mode
Send Batch Data
Batch Only Mode
Enter Parameter Batch Mode
4-48
HS-360X Handheld DPM Scanner User Manual
Radio Communications
Exit Parameter Batch Mode
HS-360X Handheld DPM Scanner User Manual
4-49
Persistent Batch Storage
Persistent Batch Storage
Parameter #1399
When the scanner is configured for Persistent Batch Storage, batch data is stored in non-volatile
memory and preserved even when the scanner is powered down. This parameter is Disabled
by default.
Frequently storing batch data with this setting Enabled will shorten the life of the non-volatile
memory.
* Persistent Batch Disable
(0)
Persistent Batch Enable
(1)
4-50
HS-360X Handheld DPM Scanner User Manual
Radio Communications
Page Button
Parameter # 746
The cradle offers a page button. The page button is a sensor that when touched, causes
paired scanners to emit a beeping sequence. The default is Enable Page Button.
1. Place your finger over the page button sensor.
2. Press down for approximately 1 second.
3. The cradle LED will turn blue when the scanner is out of the cradle. The paired scanner
will beep, blink, and vibrate. If multiple scanners are paired to the cradle, all the scanners
will beep, blink, and vibrate.
4. Repeat as necessary.
Scanners out of radio range will not beep when paged.
Scan one of the following programming symbols to enable or disable this feature.
Disable Page Button
(0)
* Enable Page Button
(1)
HS-360X Handheld DPM Scanner User Manual
4-51
Page Options
Page Options
To select a page option, select one of the programming symbols below.
Page Mode
Parameter # 1364
• Page State - In this mode, the cradle sends a page state request to each scanner. It
remains in Page State indication until every scanner sends an acknowledgment.
The scanner enters Page State when the LED indicator is blinking blue and the vibrating
motor and beeper are activated. When the trigger is pressed, or the scanner is inserted
into the cradle, or the requested timeout (default is 30 seconds) is reached, the scanner
sends the acknowledgment to the cradle and returns to its normal state.
• Page Simple - In this mode, the cradle sends a page indication request to each scanner,
and returns to idle state. Each scanner issues a single Page State indication.
Page State
(1)
* Page Simple
(0)
4-52
HS-360X Handheld DPM Scanner User Manual
Radio Communications
Page State Timeout
Parameter # 1365
Page timeout is programmable in 1 second increments from 1 to 99 seconds. The default
timeout is 30 seconds.
Page State Timeout only applies to Page State Mode.
To set a page timeout:
1. Scan the Page Timeout programming symbol below.
2. Scan two numeric programming symbols that correspond to the desired timeout
duration. Enter a leading zero for single digit numbers (for example, for a 5 second
page timeout, scan the 0 programming symbol and then the 5 programming symbol).
Page Timeout
HS-360X Handheld DPM Scanner User Manual
4-53
Classic Bluetooth and/or Low Energy
Classic Bluetooth and/or Low Energy
(Cradle Host Only)
Parameter # 1355
Set up cradle to accept both Bluetooth Classic and Low Energy connections or Low Energy
Only connections.
All Classic Bluetooth connections must be terminated before the setting can change to Low
Energy Only.
* Classic Bluetooth and Low Energy
(0)
Low Energy Only
(1)
4-54
HS-360X Handheld DPM Scanner User Manual
Radio Communications
Bluetooth Security
The scanner supports Bluetooth Authentication. Authentication can be requested by either
the remote device or the scanner.
A remote device can still request Authentication.
PIN Code
Parameter # 552
To set and store a PIN code (e.g., password) on the scanner to connect to the host:
1. Scan the Set and Store PIN Code programming symbol below.
2. Scan five alphanumeric programming symbols using the alphanumeric programming
symbols.
3. Scan End of Message in the Advanced Data Formatting Guide.
The default PIN code is 12345.
If the scanner communicates with a host with enabled, synchronize the PIN codes on the
scanner and host. To achieve this, connect the scanner to the host when setting the PIN
codes. If the scanner is not connected to a host, the PIN code change only takes affect on
the scanner. If is required between the scanner and host, and the PIN codes do not match,
pairing fails.
An extended 16 character PIN code is available for additional with Open Bluetooth
(SPP and HID).
Set and Store PIN Code
HS-360X Handheld DPM Scanner User Manual
4-55
Bluetooth Security
Variable PIN Code
Parameter # 608
When switching to Cradle Host mode with authentication enabled, scan Static PIN Code
below to avoid entering the PIN code manually. The PIN stored in memory is used. Scan the
Variable PIN Code below to manually enter a PIN code with each connection.
The default PIN code is the user-programmed PIN set and stored above. Typically, however,
HID connections require entering a Variable PIN Code. If, when attempting connection, the
application presents a text box that includes a PIN, scan the Variable PIN Code programming
symbol, then re-attempt connection. When you hear a beep indicating the scanner is waiting
for an alphanumeric entry, enter the provided variable PIN using the Alphanumeric Programming
Barcodes, then scan End of Message. if the code is less than 16 characters. The scanner
discards the variable PIN code after connection.
* Static PIN Code
(0)
Variable PIN Code
(1)
4-56
HS-360X Handheld DPM Scanner User Manual
Radio Communications
Bluetooth Security Levels
Parameter # 1393
• Low Bluetooth Security - The low security setting is designed for ease of connection
with most devices. This setting may be unacceptable to some devices. If connection
fails, try re-connecting after increasing security setting on the scanner.
If connecting to Bluetooth 2.1 device and above, Just Works method for secure and
simple pairing is used.
Data is encrypted using the Low Bluetooth security setting if connected to a Bluetooth
2.1 and above device.
• Medium Bluetooth Security - The medium security setting may require a passkey for
the initial connection to pair scanner and device.
If connecting to Bluetooth 2.1 device and above, Passkey Entry method for secure and
simple pairing is used.
• High Bluetooth Security - The high security setting enables Man in the Middle protection
for Bluetooth 2.1 and above. Not all devices are able to support this mode.
• Legacy Bluetooth Security (Bluetooth 2.0 and below) - The legacy security setting
enables authentication and encryption for legacy pairing.
* Low Bluetooth Security
(0)
Medium Bluetooth Security
(1)
HS-360X Handheld DPM Scanner User Manual
4-57
Bluetooth Security
High Bluetooth Security
(2)
Legacy Bluetooth Security
(3)
4-58
HS-360X Handheld DPM Scanner User Manual
Radio Communications
Bluetooth Radio, Linking, and Batch Operation
The HS-360X Wireless Scanner has a Bluetooth Class 1 radio which achieves a range of at
least 135m / 440ft (open air, line of sight). The actual range you achieve is influenced by the
presence of other radios, shelving and wall materials as well as which cradle is tested. The
environments vary widely and often influence radio ranges.
When the scanner goes out of communications range to the base, it can be configured for
Batch Mode. The scanner has sufficient on board memory to store 500 barcodes of typical
size (UPC/EAN).
Setting Up an iOS or Android Product To Work with the Scanner
Perform the following steps on each device to establish a link.
HID Keyboard Emulation
1. On the HS-360X Wireless Scanner, scan Keyboard Emulator (HID).
2. On an iOS/iPad/iPhone, select Settings > General > Bluetooth and turn Bluetooth
On. Choose the HS-360X Wireless Scanner from the list of discovered devices. A
link should be established allowing scanning into any application with keyboard entry.
3. On an Android/ET1/Droid, select Settings > Wireless and networks > Bluetooth (to
turn Bluetooth on, if not already on). Select Bluetooth Settings and choose the HS-360X
Wireless Scanner from the list of discovered devices. (The HS-360X Wireless Scanner
normally displays as HS-360X Wireless Scanner - xxxxxx, where xxxxxx is the serial number.)
Android devices, specifically the ET1, may require you to scan a PIN to connect. If so,
a PIN displays on the device. To enter the required PIN, scan the programming symbol,
then re-attempt connection. When a beep sounds, indicating the scanner is waiting for
PIN entry, scan the PIN using the Appendix H — Numeric Keyboard.
HS-360X Handheld DPM Scanner User Manual
4-59
Bluetooth Radio, Linking, and Batch Operation
4-60
HS-360X Handheld DPM Scanner User Manual
5 User Preferences and
Miscellaneous Options
This section describes user preferences and provides configuration symbols for those preferences.
HS-360X Handheld DPM Scanner User Manual
5-1
Introduction
Introduction
If the default values shown in this section suit your application requirements, programming
is not necessary.
To set feature values, scan a single programming symbol or a short programming symbol
sequence. The settings are stored in non-volatile memory and are preserved even when the
scanner is powered down.
Most computer monitors allow scanning the programming symbols directly on the screen.
When scanning from the screen, be sure to set the document magnification to a level
where you can see the programming symbol clearly, and bars and/or spaces are not merging.
If not using a USB cable, select a host type (see each host chapter for specific host information)
after the power-up beeps sound. This is only necessary upon the first power-up when connected
to a new host.
Scanning Sequence Examples
In most cases, scanning one programming symbol sets the parameter value. For example,
to set the beeper tone to high, scan the High Frequency (beeper tone) programming
symbol. The scanner issues a fast warble beep and the LED turns green, signifying a
successful parameter entry.
Other parameters require scanning several programming symbols. See these parameter
descriptions for this procedure.
Errors While Scanning
Unless otherwise specified, to correct an error during a scanning sequence, just re-scan the
correct parameter.
5-2
HS-360X Handheld DPM Scanner User Manual
User Preferences and Miscellaneous Options
User Preferences Parameter Defaults
The table below lists defaults for user preferences parameters. To change the default values:
• Scan the appropriate programming symbols in this guide. These new values replace the
standard default values in memory.
• Configure the scanner using WebLinkPC.
See Appendix A — Standard Default Parameters for all user preferences, hosts, symbologies,
and default parameters.
Parameter
Parameter
Number 1
Default
User Preferences
Set Default Parameter
Parameter Barcode Scanning
Restore Defaults
236
Enable
Beep After Good Decode
56
Enable
Direct Decode Indicator
859
Disable
Beeper Volume
140
High
Beeper Tone
145
Medium
Beeper Duration
628
Medium
Suppress Power Up Beeps
721
Do Not Suppress
Decode Pager Motor
613
Enable
Decode Pager Motor Duration
626
150 msec
Low Power Mode
128
Enable (HS-360X Wireless Scanner)
Disable (HS-360X Wired Scanner)
Time Delay to Low Power Mode
146
100 ms (HS-360X Wireless Scanner)
1 Hour (HS-360X Wired Scanner)
Timeout to Low Power Mode from Auto Aim (HS-360X
729
Wired Only)
15 Seconds
Handheld Trigger Mode
138
Level
Hands-Free Mode
630
Enable
Handheld Decode Aiming Pattern
306
Enable
Hands-Free (Presentation) Decode Aiming Pattern
590
Enable Hands-Free (Presentation)
Decode Aiming Pattern on PDF
Picklist Mode
402
Disabled Always
FIPS Mode
(HS-360X Wired Scanner Only)
736
Disable
Continuous Barcode Read
649
Disable
Unique Barcode Reporting
723
Enable
Decode Session Timeout
136
9.9 Seconds
Hands-free Decode Session Timeout
400
15
1. Parameter number decimal values are used for programming via RSM commands.
HS-360X Handheld DPM Scanner User Manual
5-3
User Preferences Parameter Defaults
Parameter
Parameter
Number 1
Default
Timeout Between Decodes, Same Symbol
137
0.5 Seconds
Timeout Between Decodes, Different Symbols
144
0.5 Seconds
Mobile Phone/Display Mode
716
Normal
PDF Prioritization
719
Disable
PDF Prioritization Timeout
720
200 msec
Presentation Mode Field of View
609
Full
Decoding Illumination
298
Enable
Motion Tolerance (Handheld Trigger Mode Only)
858
Less Motion Tolerance
Ranging Light Immunity
1722
60Hz Immunity
Battery Threshold
Battery Status High Threshold
Battery Status Medium Threshold
Battery Status Low Warning Threshold
Battery Health Low Warning Threshold
1367
1368
1369
1370
50%
20%
10%
60%
Add an Enter Key
N/A
N/A
Transmit Code ID Character
45
None
Prefix Value
99, 105
7013 <CR><LF>
Suffix 1 Value
Suffix 2 Value
98, 104
100, 106
7013 <CR><LF>
Scan Data Transmission Format
235
Data as is
FN1 Substitution Values
103, 109
7013 <CR><LF>
Transmit “No Read” Message
94
Disable
Unsolicited Heartbeat Interval
1118
Disable
UID
740
Disable
UID Error Mode Options
742
UID Error Beep
Decoder Effort Level
1438
Level 3
DPM Illumination Control
429
Cycle Illumination
1. Parameter number decimal values are used for programming via RSM commands.
5-4
HS-360X Handheld DPM Scanner User Manual
User Preferences and Miscellaneous Options
User Preferences
Default Parameters
The scanner can be reset to two types of defaults: factory defaults or custom defaults.
Scan the appropriate programming symbol below to reset the scanner to its default settings
and/or set the scanner’s current settings as the custom default.
Restore Defaults - Resets all default parameters as follows:
• If custom default values were configured (see Write to Custom Defaults), the custom
default values are set for all parameters each time the Restore Defaults programming
symbol below is scanned.
• If no custom default values were configured, the factory default values are set for all
parameters each time the Restore Defaults programming symbol below is scanned.
(For factory default values, see Appendix A — Standard Default Parameters.
• Set Factory Defaults - Scan the Set Factory Defaults programming symbol below to
eliminate all custom default values and set the scanner to factory default values (For
factory default values, see Appendix A — Standard Default Parameters.
• Write to Custom Defaults - Custom default parameters can be configured to set unique
default values for all parameters. After changing all parameters to the desired default
values, scan the Write to Custom Defaults programming symbol below to configure
custom defaults.
* Restore Defaults
Set Factory Defaults
Write to Custom Defaults
HS-360X Handheld DPM Scanner User Manual
5-5
User Preferences
Parameter Barcode Scanning
Parameter # 236
To disable the decoding of parameter programming symbols, including the Set Defaults
parameter programming symbols, scan the Disable Parameter Scanning programming
symbol below. To enable decoding of parameter programming symbols, scan Enable
Parameter Scanning.
* Enable Parameter Barcode Scanning
(1)
Disable Parameter Barcode Scanning
(0)
5-6
HS-360X Handheld DPM Scanner User Manual
User Preferences and Miscellaneous Options
Beep After Good Decode
Parameter # 56
Scan a programming symbol below to select whether or not the scanner beeps after a
good decode. If selecting Do Not Beep After Good Decode, the beeper still operates
during parameter menu scanning and to indicate error conditions.
* Beep After Good Decode (Enable)
(1)
Do Not Beep After Good Decode
(Disable)
(0)
HS-360X Handheld DPM Scanner User Manual
5-7
User Preferences
Direct Decode Indicator
Parameter # 859
This feature is only supported in Auto Aim and Standard (Level) trigger modes. Scan a
programming symbol below to select optional blinking of the illumination on a successful
decode:
• Disable Direct Decode Indicator - illumination does not blink on a successful decode.
• 1 Blink - illumination blinks once upon a successful decode.
• 2 Blinks - illumination blinks twice upon a successful decode.
* Disable Direct Decode Indicator
(0)
1 Blink
(1)
2 Blinks
(2)
5-8
HS-360X Handheld DPM Scanner User Manual
User Preferences and Miscellaneous Options
Beeper Volume
Parameter # 140
To select a beeper volume, scan the Low Volume, Medium Volume, or High Volume
programming symbol.
Low Volume
(2)
Medium Volume
(1)
* High Volume
(0)
HS-360X Handheld DPM Scanner User Manual
5-9
User Preferences
Beeper Tone
Parameter # 145
To select a beeper tone, scan one of the following programming symbols.
Off
(3)
Low Tone
(2)
* Medium Tone
(1)
High Tone
(0)
5-10
HS-360X Handheld DPM Scanner User Manual
User Preferences and Miscellaneous Options
Medium to High Tone (2-tone)
(4)
HS-360X Handheld DPM Scanner User Manual
5-11
User Preferences
Beeper Duration
Parameter # 628
To select the duration for the beeper, scan one of the following programming symbols.
Short
(0)
* Medium
(1)
Long
(2)
5-12
HS-360X Handheld DPM Scanner User Manual
User Preferences and Miscellaneous Options
Suppress Power Up Beeps
Parameter # 721
Scan a programming symbol below to select whether or not to suppress the scanner’s
power-up beeps.
* Do Not Suppress Power Up Beeps
(0)
Suppress Power Up Beeps
(1)
HS-360X Handheld DPM Scanner User Manual
5-13
User Preferences
Decode Pager Motor
Parameter # 613
The scanner includes a pager motor which, when enabled, vibrates the scanner for a
period of time when a successful decode occurs.
When the pager motor is enabled and the HS-360X Wired Scanner is in the HS-360X
Stand, the pager motor disables until the scanner is removed from the HS-360X Stand.
Scan a programming symbol below to enable or disable the pager motor. If enabled, scan
the appropriate programming symbol to set the period of time in which to vibrate the scanner.
Pager Motor Disable
(0)
* Pager Motor Enable
(1)
5-14
HS-360X Handheld DPM Scanner User Manual
User Preferences and Miscellaneous Options
Decode Pager Motor Duration
Parameter # 626
* 150 msec
(15)
200 msec
(20)
250 msec
(25)
300 msec
(30)
HS-360X Handheld DPM Scanner User Manual
5-15
User Preferences
400 msec
(40)
500 msec
(50)
600 msec
(60)
750 msec
(75)
5-16
HS-360X Handheld DPM Scanner User Manual
User Preferences and Miscellaneous Options
Low Power Mode
Parameter # 128
This parameter determines whether or not the scanner enters low power mode after a
decode attempt.
If disabled, power remains on after each decode attempt. The HS-360X Wired Scanner
default is Disable. The HS-360X Wireless Scanner default is Enable.
Disable Low Power Mode
(0)
Enable Low Power Mode
(1)
HS-360X Handheld DPM Scanner User Manual
5-17
User Preferences
Time Delay to Low Power Mode
Parameter # 146
This parameter only applies when Lower Power Mode is enabled.
This parameter sets the time it takes the scanner to enter Low Power Mode after any
scanning activity. Scan the appropriate programming symbol below to set the time. The
HS-360X Wired Scanner default is 1 Hour. The HS-360X Wireless Scanner default is 100 msec.
100 msec
(65)
500 msec
(69)
1 Second
(17)
2 sec
(18)
5-18
HS-360X Handheld DPM Scanner User Manual
User Preferences and Miscellaneous Options
3 sec
(19)
4 Seconds
(20)
5 Seconds
(21)
10 Seconds
(26)
1 Minute
(33)
HS-360X Handheld DPM Scanner User Manual
5-19
User Preferences
5 Minutes
(37)
15 Minutes
(43)
30 Minutes
(45)
45 Minutes
(46)
1 Hour
(49)
5-20
HS-360X Handheld DPM Scanner User Manual
User Preferences and Miscellaneous Options
3 Hours
(51)
6 Hours
(54)
9 Hours
(57)
HS-360X Handheld DPM Scanner User Manual
5-21
User Preferences
Timeout to Low Power Mode from Auto Aim
Parameter # 729
Timeout to Low Power Mode from Auto Aim applies to the HS-360X Wired Scanner only.
This parameter sets the time the scanner remains in auto aim before entering Low Power Mode.
Disabled
(0)
5 Seconds
(5)
* 15 Seconds
(11)
5-22
HS-360X Handheld DPM Scanner User Manual
User Preferences and Miscellaneous Options
30 Seconds
(13)
1 Minute
(17)
HS-360X Handheld DPM Scanner User Manual
5-23
User Preferences
Handheld Trigger Mode
Parameter # 138
Select one of the following trigger modes for the scanner.
• Standard (Level) - A trigger pull activates decode processing. Decode processing
continues until the barcode decodes, you release the trigger, or the Decode Session
Timeout occurs.
• Presentation (Blink) - The scanner activates decode processing when it detects a
barcode in its field of view. After a period of non-use, the scanner enters a low power
mode, in which the LEDs turn off until the scanner senses motion.
The scanner uses an internal dim illumination state when it enters low power mode until
motion is detected.
* Level (Standard)
(0)
Presentation (Blink)
(7)
5-24
HS-360X Handheld DPM Scanner User Manual
User Preferences and Miscellaneous Options
Hands-Free Mode
Parameter # 630
If you select Disable Hands-free Mode, the scanner behaves according to the setting of
the Handheld Trigger Mode.
* Enable Hands-free Mode
(1)
Disable Hands-free Mode
(0)
HS-360X Handheld DPM Scanner User Manual
5-25
User Preferences
Handheld Decode Aiming Pattern
Parameter # 306
Select Enable Handheld Decode Aiming Pattern to project the aiming dot during barcode
capture, Disable Handheld Decode Aiming Pattern to turn the aiming dot off, or Enable
Handheld Decode Aiming Pattern on PDF to project the aiming dot when the scanner
detects a 2D barcode.
With Picklist Mode enabled, the decode aiming dot flashes even when the Handheld
Decode Aiming Pattern is disabled.
* Enable Handheld Decode Aiming
Pattern
(2)
Disable Handheld Decode Aiming Pattern
(0)
Enable Handheld Decode Aiming Pattern
on PDF
(3)
5-26
HS-360X Handheld DPM Scanner User Manual
User Preferences and Miscellaneous Options
Hands-Free Decode Aiming Pattern
Parameter # 590
Select Enable Hands-free Decode Aiming Pattern to project the aiming dot during
barcode capture, Disable Hands-free Decode Aiming Pattern to turn the aiming dot off,
or Enable Hands-free Decode Aiming Pattern on PDF to project the aiming dot when
the scanner detects a 2D barcode.
With Picklist Mode enabled, the decode aiming dot flashes even when the Decode
Aiming Pattern is disabled.
Enable Hands-Free Decode
Aiming Pattern
(1)
Disable Hands-Free Decode
Aiming Pattern
(0)
* Enable Hands-Free Decode
Aiming
Pattern on PDF
(2)
HS-360X Handheld DPM Scanner User Manual
5-27
User Preferences
FIPS Mode
Parameter # 736
FIPS Mode applies to the HS-360X Wired Scanner only.
The Federal Information Processing Standard (FIPS) 140-2 is a U.S. government computer
security standard used to accredit cryptographic modules. FIPS enabled HS-360X Wired
Scanners and cradles offer this secure mode of operation.
To enable the FIPS mode of operation (disabled by default), scan the Enable FIPS programming
symbol. The scanner attempts to establish a secure session with the cradle to which it is
connected. On success, the scanner lights an amber LED on every trigger pull to signal
that all data will be transmitted over Bluetooth in a secure fashion. On failure, the scanner
will sound transmission failure error message on every attempt to transmit data.
To disable the FIPS mode, scan the Disable FIPS programming symbol at any time.
Enable FIPS
(1)
* Disable FIPS
(0)
5-28
HS-360X Handheld DPM Scanner User Manual
User Preferences and Miscellaneous Options
Decode Session Timeout
Parameter # 136
This parameter sets the maximum time decode processing continues during a scan
attempt. It is programmable in 0.1 second increments from 0.5 to 9.9 seconds. The default
timeout is 9.9 seconds.
To set a Decode Session Timeout, scan the programming symbol below. Next, scan two
numeric programming symbol from Appendix H — Numeric Keyboard that correspond
to the desired on time. Enter a leading zero for single digit numbers. For example, to set a
Decode Session Timeout of 0.5 seconds, scan the programming symbol below, then scan
the 0 and 5 programming symbols.
Decode Session Timeout
HS-360X Handheld DPM Scanner User Manual
5-29
User Preferences
Hands-Free Decode Session Timeout
Parameter # 400
This parameter is the Hands-free compliment to the Decode Session Timeout. It configures
the minimum and maximum decode processing time during a Hands-free scan attempt. It
only applies to the Hands-free trigger mode.
The minimum decode processing time is defined as the time in which the scanner stops
decoding when an object is removed or left stationary in the imaging field of view.
The maximum decode processing time is defined as the time in which the scanner stops
decoding when an object is left in or is moving in the field of view.
Both the maximum and minimum times are configured using a single setting. The relationship
of this setting is as follows:
Setting Value
Minimum Time
Maximum Time
X < 25
250 msec
2.5 Seconds
X >= 25
X * 10 msec
X * 100 msec
For example, a setting value of 100 results in the scanner turning off approximately 1 second
after an object is removed from the field of view or 10 seconds while an object is in the
field of view moving.
The default value of the setting is 15 which results in a Minimum time of 250 msec and
Maximum time of 2.5 seconds.
Adjust this setting based on your requirements. For example, when doing prioritization,
this parameter should be set to a value where the maximum time is above the PDF prioritization
timeout.
Hands-free Decode Session Timeout
5-30
HS-360X Handheld DPM Scanner User Manual
User Preferences and Miscellaneous Options
Timeout Between Decodes
Parameter # 144
Use this option in presentation mode to control the time the scanner is inactive between
decoding different symbols. It is programmable in 0.1 second increments from 0.1 to 9.9
seconds. The default is 0.5 seconds.
Note: Values below 0.5 seconds result in barcodes being read faster than WeblinkPC can
process the corresponding images.
To select the timeout between decodes for different symbols, scan the programming
symbol below, then scan two numeric programming symbols from Appendix H —
Numeric Keyboard that correspond to the desired interval, in 0.1 second increments.
Timeout Between Decodes cannot be greater than or equal to the Decode Session
Timeout.
Timeout Between Decodes
HS-360X Handheld DPM Scanner User Manual
5-31
User Preferences
Mobile Phone/Display Mode
Parameter # 716
This mode improves barcode reading performance off mobile phones and electronic displays.
Select Enhanced in Handheld, Hands-free, or both modes, or select Normal Mobile
Phone/Display Mode.
The scanner restricts Mobile Phone/Display Mode.
* Normal Mobile Phone/Display Mode
(0)
Enhanced in Handheld Mode
(1)
Enhanced in Hands-free Mode
(2)
Enhanced in Both Modes
(3)
5-32
HS-360X Handheld DPM Scanner User Manual
User Preferences and Miscellaneous Options
PDF Prioritization
Parameter # 719
Enable this feature to delay decoding a 1D barcode (Code 128) by the value specified in
PDF Prioritization Timeout. During that time the scanner attempts to decode a PDF417
symbol (e.g., on a US driver's license), and if successful, reports this only. If it does not
decode (can not find) a PDF417 symbol, it reports the 1D symbol after the timeout. The 1D
symbol must be in the device’s field of view for the scanner to report it. This parameter
does not affect decoding other symbologies.
The 1D Code 128 barcode lengths include the following:
• 7 to 10 characters
• 14 to 22 characters
• 27 to 28 characters
In addition, a Code 39 barcode with the following lengths are considered to potentially be
part of a US driver’s license:
• 8 characters
• 12 characters
* Disable PDF Prioritization
(0)
Enable PDF Prioritization
(1)
HS-360X Handheld DPM Scanner User Manual
5-33
User Preferences
PDF Prioritization Timeout
Parameter # 720
The Hands-Free Decode Session Timeout should be set to a longer duration than PDF
Prioritization Timeout when configured.
When PDF Prioritization is enabled, this timeout specifies how long the scanner attempts
to decode a PDF417 symbol before reporting the 1D barcode in the field of view.
Scan the following programming symbol, then scan four digits from Appendix H —
Numeric Keyboard that specify the timeout in milliseconds. For example, to enter 400
msec, scan the following programming symbol, then scan 0400. The range is 0 to 5000
msec, and the default is 200 msec.
PDF Prioritization Timeout
5-34
HS-360X Handheld DPM Scanner User Manual
User Preferences and Miscellaneous Options
Decoding Illumination
Parameter # 298
Selecting Enable Decoding Illumination causes the scanner to flash illumination to aid
decoding. Select Disable Decoding Illumination to prevent the scanner from using
decoding illumination.
Enabling illumination usually results in superior images. The effectiveness of the illumination
decreases as the distance to the target increases.
* Enable Decoding Illumination
(1)
Disable Decoding Illumination
(0)
HS-360X Handheld DPM Scanner User Manual
5-35
User Preferences
Motion Tolerance (Handheld Trigger Modes Only)
Parameter # 858
Less Motion Tolerance provides optimal decoding performance on 1D barcodes.
To increase motion tolerance and speed decoding when scanning a series of 1D barcodes
in rapid progression, scan More Motion Tolerance.
* Less Motion Tolerance
(0)
More Motion Tolerance
(1)
5-36
HS-360X Handheld DPM Scanner User Manual
User Preferences and Miscellaneous Options
Battery Threshold
Scan the appropriate programming symbol below to select the desired battery status threshold.
• Battery Status High Threshold - Parameter #1367
This parameter sets the threshold used to show the Battery Status is High. When the
battery status is above the High Threshold, the battery indicator is green. Scan this
programming symbol followed by 2 digits from Appendix H — Numeric Keyboard that
correspond to the desired percentage from 00 to 99. The default is 50%.
• Battery Status Medium Threshold - Parameter #1368
This parameter sets the threshold used to show the Battery Status is Medium. When the
battery status is above the Medium Threshold (and below the High Threshold), the
Battery indicator is amber. When the battery status is below the Medium Threshold, the
Battery indicator is red. Scan this programming symbol followed by 2 digits from
Appendix H — Numeric Keyboard that correspond to the desired percentage from 00
to 99. The default is 20%.
• Battery Status Low Warning Threshold - Parameter #1369
This parameter sets the threshold to indicate Batter Status is Critically Low. When the
battery status is below the Low Warning Threshold, on every trigger release the scanner
issues 4 short beeps. Scan this programming symbol followed by 2 digits from
Appendix H — Numeric Keyboard that correspond to the desired percentage from 00
to 99. The default is 10%.
• Battery Health Low Warning Threshold - Parameter #1370
This parameter sets the threshold to indicate Battery Health is Low. When the battery
health is below the Low Health Threshold, all battery indication will alternate between
Red and the appropriate Battery Status indication. When Battery Health is Low, you
should consider replacing the battery. Scan this programming symbol followed by 2 digits
from Appendix H — Numeric Keyboard that correspond to the desired percentage
from 00 to 99. The default is 60%.
Battery Status High Threshold
Battery Status Medium Threshold
HS-360X Handheld DPM Scanner User Manual
5-37
User Preferences
Battery Status Low Warning Threshold
Battery Health Low Warning Threshold
5-38
HS-360X Handheld DPM Scanner User Manual
User Preferences and Miscellaneous Options
Add an Enter Key
To add an Enter key (carriage return/line feed) after scanned data, scan the following
programming symbol.
Add Enter Key (Carriage Return/Line
Feed)
HS-360X Handheld DPM Scanner User Manual
5-39
User Preferences
Transmit Code ID Character
Parameter # 45
A Code ID character identifies the code type of a scanned barcode. This is useful when
decoding more than one code type. In addition to any single character prefix already
selected, the Code ID character is inserted between the prefix and the decoded symbol.
Select no Code ID character, a Symbol Code ID character, or an AIM Code ID character.
If you enable Symbol Code ID Character or AIM Code ID Character, and enable Transmit
“No Read” Message, the scanner appends the code ID for Code 39 to the NR message.
Symbol Code ID Character
(2)
AIM Code ID Character
(1)
* None
(0)
5-40
HS-360X Handheld DPM Scanner User Manual
User Preferences and Miscellaneous Options
Prefix/Suffix Values
Key Category Parameter # P = 99, S1 = 98, S2 = 100
Decimal Value Parameter # P = 105, S1 = 104, S2 = 106
You can append a prefix and/or one or two suffixes to scan data for use in data editing. To
set a value for a prefix or suffix, scan a four-digit number (i.e., four programming symbols
from Appendix H — Numeric Keyboard) that corresponds to that value. See
Appendix I — ASCII Character Sets for the four-digit codes.
When using host commands to set the prefix or suffix, set the key category parameter to 1,
then set the 3-digit decimal value. See Appendix I — ASCII Character Sets for the
four-digit codes.
The default prefix and suffix value is 7013 <CR><LF> (the Enter key).
Scan Prefix
(7)
Scan Suffix 1
(6)
Scan Suffix 2
(8)
HS-360X Handheld DPM Scanner User Manual
5-41
User Preferences
Data Format Cancel
5-42
HS-360X Handheld DPM Scanner User Manual
User Preferences and Miscellaneous Options
Scan Data Transmission Format
Parameter # 235
To change the scan data format, scan one of the following eight programming symbol
corresponding to the desired format.
If using this parameter do not use ADF rules to set the prefix/suffix.
To set values for the prefix and/or suffix, see Prefix/Suffix Values.
* Data As Is
(0)
<DATA> <SUFFIX 1>
(1)
<DATA> <SUFFIX 2>
(2)
<DATA> <SUFFIX 1> <SUFFIX 2>
(3)
HS-360X Handheld DPM Scanner User Manual
5-43
User Preferences
<PREFIX> <DATA >
(4)
<PREFIX> <DATA> <SUFFIX 1>
(5)
<PREFIX> <DATA> <SUFFIX 2>
(6)
<PREFIX> <DATA> <SUFFIX 1> <SUFFIX
2>
(7)
5-44
HS-360X Handheld DPM Scanner User Manual
User Preferences and Miscellaneous Options
FN1 Substitution Values
Key Category Parameter # 103
Decimal Value Parameter # 109
The wedge and USB HID keyboard hosts support a FN1 Substitution feature. Enabling
this substitutes any FN1 character (0x1b) in an EAN128 barcode with a value. This value
defaults to 7013 (Enter Key).
When using host commands to set the FN1 substitution value, set the key category
parameter to 1, then set the 3-digit keystroke value. See the ASCII Character Set table for
the current host interface for the desired value.
To select a FN1 substitution value via programming symbol menus:
1. Scan the programming symbol below.
Set FN1 Substitution Value
2. Locate the keystroke desired for FN1 Substitution in the ASCII Character Set table
for the current host interface. Enter the 4-digit ASCII Value by scanning each digit in
Appendix H — Numeric Keyboard.
To correct an error or change the selection, scan Cancel.
To enable FN1 substitution for USB HID keyboard, scan the Enable FN1 Substitution
programming symbol.
HS-360X Handheld DPM Scanner User Manual
5-45
User Preferences
Transmit “No Read” Message
Parameter # 94
Scan a programming symbol below to select whether or not to transmit a No Read message.
Enable this to transmit the characters NR when a successful decode does not occur
before trigger release or the Decode Session Timeout expires. Disable this to send
nothing to the host if a symbol does not decode.
If you enable Transmit No Read, and also enable Symbol Code ID Character or AIM
Code ID Character for Transmit Code ID Character the scanner appends the code ID for
Code 39 to the NR message.
Important: When connected to Setup in WebLinkPC, do not use these programming
symbols. See the WebLinkPC ReadMe for further details.
Enable No Read
(1)
* Disable No Read
(0)
5-46
HS-360X Handheld DPM Scanner User Manual
User Preferences and Miscellaneous Options
Unsolicited Heartbeat Interval
Parameter # 1118
The imager supports sending Unsolicited Heartbeat Messages to assist in diagnostics.
To enable this feature and set the desired unsolicited heartbeat interval, scan one of the
time interval programming symbols below, or scan Set Another Interval followed by four
numeric programming symbols from Appendix H — Numeric Keyboard (scan sequential
numbers that correspond to the desired number of seconds). The range is 0 - 9999.
Scan Disable Unsolicited Heartbeat Interval to turn off the feature.
The heartbeat event is sent as decode data (with no decode beep) in the form of:
MOTEVTHB:nnn
where nnn is a three-digit sequence number starting at 001 and wrapping after 100.
10 Seconds
(10)
1 Minute
(60)
Set Another Interval
HS-360X Handheld DPM Scanner User Manual
5-47
User Preferences
* Disable Unsolicited Heartbeat Interval
(0)
5-48
HS-360X Handheld DPM Scanner User Manual
User Preferences and Miscellaneous Options
UID Parsing
Parameter # 740
UID parsing is only supported by DP configurations of the scanner.
UID constructs are compliant with the US Department of Defense MIL - STD - 130N.
A UID, or Unique Identifier, is used to identify and track data (e.g., manufacturer, distribution,
lifetime of products and other information) specified by the United States Department of
Defense for all imported packages containing merchandise equal to or greater than
$5,000.00. Vendors are required to provide a legible and permanent UID marking, in the
form of a Data Matrix symbol, with the contents.
DP configurations of the scanner read the Data Matrix symbol, verify it is a valid UID
symbol and parse the data into a UID symbol (Criterion: Parsed UID symbol type with
UID fields). This output can be used at a later date.
To enable/disable UID parsing, scan the appropriate programming symbol below. UID parsing
is disabled by default. Scan Enable Embedded UID Parsing to start the parsing process.
* Disable UID Parsing
(0)
Enable Embedded UID Parsing
(1)
HS-360X Handheld DPM Scanner User Manual
5-49
User Preferences
UID Parsing Output
When a UID is successfully parsed, the fields shown below are created. Each field is
comma-separated. If data is missing from a field in the UID, a lone comma fills the field.
When a UID successfully parses, a parsed UID symbol type transmits to the host.
When parsing is unsuccessful but data transmits to the host anyway, the data is in the data
matrix format.
Field
Description
1
Concatenated UID
2
Construct type (UID1 or UID2)
3
Enterprise ID
4
Serialized part #
5
Original part #
6
Lot #
7
Current part #
8
Scanned data in ASCII mode
Example Output – Successful Parsed Data
D12345WS51-004041,UID2,12345,041,WS51-004,,,[)> rs 06 gs 17V12345 gs 1PWS51-004
gs S041 rs eot
Field
Description
1
D12345WS51-004041
2
UID2
3
12345
4
041
5
WS51-004
6
(no data supplied, comma filled field)
7
(no data supplied, comma filled field)
8
[)> rs 06 gs 17V12345 gs 1PWS51-004 gs S041 rs eot
5-50
HS-360X Handheld DPM Scanner User Manual
User Preferences and Miscellaneous Options
UID Error Mode Options
Parameter # 742
• UID Error Beep (default):
Scan UID Error Beep to program the scanner not
to parse the data contained in the UID when the
UID is not formatted correctly. An error tone
sounds and no data transmits to the host.
• UID Error Pass Data:
Scan UID Error Pass Data to program the scanner
to transmit data to the host even when parsing
fails. The scanner reads the incorrectly encoded
UID, assumes the host can process the data and
transmits the unformatted contents of the barcode.
No error tone sounds.
• UID Error Beep and Pass Data: Scan UID Error Pass Data to program the scanner
to transmit data to the host even when parsing
fails. The scanner reads the incorrectly encoded
UID, assumes the host can process the data and
transmits the unformatted contents of the barcode.
An error tone sounds.
Scan the appropriate programming symbol below to program potential error conditions.
* UID Error Beep
(0)
UID Error Pass Data
(1)
HS-360X Handheld DPM Scanner User Manual
5-51
User Preferences
UID Error Beep and Pass Data
(2)
5-52
HS-360X Handheld DPM Scanner User Manual
User Preferences and Miscellaneous Options
Sample ADF Rule for UID
To transmit only the concatenated UID field of the parsed UID, scan the programming
symbols below, in order.
Begin New Rule
Criterion: Parsed UID
Send Data Up to Character
HS-360X Handheld DPM Scanner User Manual
5-53
User Preferences
,
(Comma)
Save Rule
5-54
HS-360X Handheld DPM Scanner User Manual
User Preferences and Miscellaneous Options
UID Sample Barcodes
05 Format
WS51-004041,UID2,,041,WS51-004,,,[)> rs 05 gs 01WS51-004 gs 21041 rs eot
Field
Description
1 - Concatenated UID
WS51-004041
2 - Construct type (UID1 or UID2)
UID2
3 - Enterprise ID
, (no data supplied)
4 - Serialized part #
041
5 - Original part #
WS51-004
6 - Lot #
, (no data supplied)
7 - Current part #
, (no data supplied)
8 - Scanned data in ASCII mode
[)> rs 05 gs 01WS51-004 gs 21041 rs eot
06 Format
D12345WS51-004041,UID2,12345,041,WS51-004,,,[)> rs 06 gs 17V12345 gs 1PWS51-004 gs S041
rs eot
Field
Description
1 - Concatenated UID
D12345WS51-004041
2 - Construct type (UID1 or UID2)
UID2
3 - Enterprise ID
12345
4 - Serialized part #
041
5 - Original part #
WS51-004
6 - Lot #
, (no data supplied)
7 - Current part #
, (no data supplied)
8 - Scanned data in ASCII mode
[)> rs 06 gs 17V12345 gs 1PWS51-004 gs S041 rs eot
HS-360X Handheld DPM Scanner User Manual
5-55
User Preferences
12 Format
D12345WS51-004041,UID2,12345,041,WS51-004,,,[)> rs 12 gs MFR 12345 gs PNO WS51-004 gs
SEQ 041 rs eot
Field
Description
1 - Concatenated UID
D12345WS51-004041
2 - Construct type (UID1 or UID2)
UID2
3 - Enterprise ID
12345
4 - Serialized part #
041
5 - Original part #
WS51-004
6 - Lot #
, (no data supplied)
7 - Current part #
, (no data supplied)
8 - Scanned data in ASCII mode
[)> rs 12 gs MFR 12345 gs PNO WS51-004 gs SEQ 041 rs eot
DD Format
D12345WS51-004041,UID2,12345,041,WS51-004,,,[)> rs DD gs MFR 12345 gs PNO WS51-004 gs
SEQ 041 rs eot
Field
Description
1 - Concatenated UID
D12345WS51-004041
2 - Construct type (UID1 or UID2)
UID2
3 - Enterprise ID
12345
4 - Serialized part #
041
5 - Original part #
WS51-004
6 - Lot #
, (no data supplied)
7 - Current part #
, (no data supplied)
8 - Scanned data in ASCII mode
[)> rs DD gs MFR 12345 gs PNO WS51-004 gs SEQ 041 rs eot
5-56
HS-360X Handheld DPM Scanner User Manual
User Preferences and Miscellaneous Options
Decoder Effort Levels
Parameter # 1438
Unlike symbols printed on labels, a direct part mark (DPM) is a symbol that is marked
directly on an item's surface for permanent identification, using methods such as laser
etching, dot-peening, or direct-printing.
Select one of the levels below based on the type of symbol being scanned.
• Decoder Effort Level 1 – No Special DPM Processing. Use only on high-contrast
symbols printed on labels. This allows the fastest processing time when no DPM reading
is required.
• Decoder Effort Level 2 – Least Aggressive DPM Processing. Optimized for decoding
performance on smaller DPM symbols typically found on electronics and medical
instruments, especially on smooth surfaces. These symbols tend to be laser-etched or
direct-printed.
• Decoder Effort Level 3 – Best Setting for Most DPMs. Optimizes decoding performance
on larger DPM symbols, typically found on industrial parts, especially on rough, grainy,
or visibly machined surfaces. These symbols tend to be dot-peened or laser-etched.
• Decoder Effort Level 4 – Most Aggressive DPM Processing. Use only for the most
difficult-to-decode marks, for which additional DPM processing may be necessary.
Level 1 – No
Special DPM
Processing
Level 2 – Least
Aggressive DPM
Processing
Level 3 – Best
Setting for
Most DPMs
Level 4 – Most Aggressive DPM Processing
(You can also use the Decoder Effort slider
in WebLinkPC to Set the Scanner’s Decoder
Effort to Level 4)
Important: The BC412 and DotCode symbologies are only supported when the
scanner is set to Decoder Effort Level 4.
HS-360X Handheld DPM Scanner User Manual
5-57
User Preferences
DPM Illumination Control
Parameter # 429
In Presentation Mode, the scanner uses the internal dim illumination state when it enters
low power mode until motion is detected.
This parameter controls the Illumination for DPM symbol reading.
• Direct Illumination – scanner uses only the direct (white) illumination. Recommended
for use with dot-peened symbols. Tilt the part 30 degrees.
• Indirect Illumination – scanner uses only the (red) illumination. Recommended for use
with laser-etched symbols on curved, rough, grainy, highly reflective, visibly machined
surfaces or cylinders.
• Cycle Illumination – scanner cycles alternately between direct and indirect illumination.
The scanner starts with the illumination used during the last successful decode.
Direct Illumination
(0)
Indirect Illumination
(8)
* Cycle Illumination
(3)
5-58
HS-360X Handheld DPM Scanner User Manual
6 Imaging Preferences
This section describes image capture preferences and provides configuration symbols for
those preferences.
HS-360X Handheld DPM Scanner User Manual
6-1
Introduction
Introduction
Only the Symbol Native API (SNAPI) with Imaging interface supports image capture.
See Appendix A — Standard Default Parameters for all host device and defaults. If the
default values suit application requirements, programming is not necessary.
To set feature values, scan a single programming symbol or a short programming symbol
sequence. The settings are stored in non-volatile memory and are preserved even when
you power down the scanner.
Most computer monitors allow scanning the programming symbols directly on the screen.
When scanning from the screen, be sure to set the document magnification to a level
where you can see the programming symbol clearly, and bars and/or spaces are not merging.
6-2
HS-360X Handheld DPM Scanner User Manual
Imaging Preferences
Scanning Sequence Examples
In most cases scanning one programming symbol sets the parameter value. For example,
to disable image capture illumination, scan the Disable Image Capture Illumination
programming symbol under Image Capture Illumination. The scanner issues a fast
“warble” beep and the LED turns green, signifying a successful parameter entry.
Other parameters require scanning several programming symbols. See these parameter
descriptions for this procedure.
Errors While Scanning
Unless otherwise specified, to correct an error during a scanning sequence, just re-scan
the correct parameter.
Imaging Preferences Parameter Defaults
The table below lists the defaults for imaging preferences parameters. To change the
default values, scan the appropriate programming symbols in this guide. These new values
replace the standard default values in memory.
See Appendix A — Standard Default Parameters for all user preferences, hosts, symbologies,
and default parameters.
Parameter
Parameter Number
Default
Image Size (Number of Pixels)
302
Full Resolution
JPEG Image Options
299
JPEG Quality Selector
Imaging Preferences
JPEG File Size
561
160 kb
JPEG Quality and Size Value
305
65
Image File Format
304
JPEG
HS-360X Handheld DPM Scanner User Manual
6-3
Imaging Preferences Parameter Defaults
Image Size (Number of Pixels)
Parameter # 302
This option alters image resolution before compression. Multiple pixels are combined to
one pixel, resulting in a smaller image containing the original content with reduced resolution.
Select one of the following values:
Resolution Value
HS-360X
Full
1280 x 800
1/2
640 x 400
1/4
320 x 200
* Full Resolution
(0)
1/2 Resolution
(1)
1/4 Resolution
(3)
6-4
HS-360X Handheld DPM Scanner User Manual
Imaging Preferences
JPEG Image Options
Parameter # 299
Select an option to optimize JPEG images for either size or for quality. Scan the JPEG
Quality Selector programming symbol to use a quality value; the scanner then selects the
corresponding image size. Scan the JPEG Size Selector programming symbol to use a
size value; the scanner then selects the best image quality.
* JPEG Quality Selector
(1)
JPEG Size Selector
(0)
JPEG Target File Size
Parameter # 561
Type: Word
Range: 5-350
This parameter defines the target JPEG file size in terms 1 Kilobytes (1024 bytes). The
default value is 160 kB which represents 160 Kilobytes.
JPEG compress may take 10 to 15 seconds based on the amount of information in the
target image. Scanning JPEG Quality Selector (default setting) produces a compressed
image that is consistent in quality and compression time.
To set the JPEG Target File Size parameter, scan JPEG Target File Size below followed
by three numeric programming symbols representing the value. Leading zeros are
required. For example, to set an image file size value of 99, scan 0, 9, 9 in Appendix H —
Numeric Keyboard.
JPEG Target File Size
(3 digits)
HS-360X Handheld DPM Scanner User Manual
6-5
Imaging Preferences Parameter Defaults
JPEG Quality and Size Value
JPEG Quality = Parameter # 305
If you selected JPEG Quality Selector, scan the JPEG Quality Value programming symbol
followed by 3 programming symbols from Appendix H — Numeric Keyboard corresponding
to a value from 5 to 100, where 100 represents the highest quality image.
JPEG Quality Value
(Default: 065)
(5 - 100 Decimal)
6-6
HS-360X Handheld DPM Scanner User Manual
Imaging Preferences
Image File Format Selector
Parameter # 304
Select an image format appropriate for the system (BMP, TIF, or JPG). The scanner stores
captured images in the selected format.
BMP File Format
(3)
* JPEG File Format
(1)
TIFF File Format
(4)
HS-360X Handheld DPM Scanner User Manual
6-7
Imaging Preferences Parameter Defaults
Image Rotation
Parameter # 665
This parameter controls the rotation of the image by 0, 90,180, or 270 degrees.
* Rotate 0o
(0)
Rotate 90o
(1)
Rotate 180o
(2)
Rotate 270o
(3)
6-8
HS-360X Handheld DPM Scanner User Manual
7 USB Interface
This section provides instructions for programming the scanner to interface with a USB host.
The scanner connects directly to a USB host or a powered USB hub. The USB host powers
the scanner.
HS-360X Handheld DPM Scanner User Manual
7-1
Connecting a USB Interface
Connecting a USB Interface
The scanner connects to USB capable hosts including:
• TGIS (IBM) terminals
• Apple™ desktops and notebooks
• Other network computers that support more than one keyboard.
The following operating systems support the scanner through USB:
• Windows® XP, 7, 8, 10
• MacOS 8.5 - MacOS 10.6
• IBM 4690 OS.
7-2
HS-360X Handheld DPM Scanner User Manual
USB Interface
Connecting the HS-360X Wireless Scanner to USB Interface
The scanner also interfaces with other USB hosts which support USB Human Interface
Devices (HID).
Note: When connecting
the HS-360X and cradle to
a PC, look for a USB port
with a lightning bolt icon
similar to the one below.
This icon indicates that the
port is higher-powered and
is intended for charging
USB devices.
USB Connection to HS-360X Wireless Scanner
To connect the cradle to a USB host:
1. Attach the modular connector of the USB interface cable to the cable interface port on
the cradle.
2. Plug the series A connector in the USB host or hub.
3. Connect an external power supply if desired.
4. Ensure all connections are secure.
5. Pair the scanner to the cradle by scanning the symbol on the cradle.
6. Select the USB device type by scanning the appropriate programming symbol.
7. On first installation when using Windows, the software displays a prompt to select or
install the Human Interface Device driver. To install the Human Interface Device
driver provided by Windows, click Next through all the choices and click Finished on
the last choice. The scanner powers up during this installation.
8. To modify any other parameter options, scan the appropriate programming symbols in
this chapter.
Note: Interface cables vary depending on configuration.
Note: Disconnect the host cables before the power supply, or the scanner may not recognize
the new host.
HS-360X Handheld DPM Scanner User Manual
7-3
Connecting a USB Interface
Connecting HS-360X Wired Scanner to USB Interface
USB Connection to HS-360X Wired Scanner
To connect the USB interface to an HS-360X Wired Scanner:
1. Attach the modular connector of the USB interface cable to the host port on the bottom
of the scanner.
2. Plug the series A connector in the USB host or hub.
3. Select the USB device type by scanning the appropriate programming symbol.
Note: The interface cable automatically detects the host type and uses the default setting.
If the default (*) does not meet your requirements, scan another host programming symbol.
4. On first installation when using Windows, the software prompts to select or install the
Human Interface Device driver. To install this driver, provided by Windows, click Next
through all the choices and click Finished on the last choice. The scanner powers up
during this installation.
5. To modify any other parameter options, scan the appropriate programming symbols in
this chapter.
7-4
HS-360X Handheld DPM Scanner User Manual
USB Interface
USB Parameter Defaults
The table below lists the defaults for USB host parameters. If any option needs to be
changed, scan the appropriate programming symbol(s) provided in the Parameter
Descriptions section.
Parameter
Default
USB Host Parameters
USB Device Type
HID Keyboard Emulation
Symbol Native API (SNAPI) Status Handshaking
Enable
USB Keystroke Delay
No Delay
USB CAPS Lock Override
Disable
USB Ignore Unknown Characters
Send
USB Convert Unknown to Code 39
Disable
Emulate Keypad
Enable
Emulate Keypad with Leading Zero
Enable
Quick Keypad Emulation
Enable
USB FN1 Substitution
Disable
Function Key Mapping
Disable
Simulated Caps Lock
Disable
Convert Case
No Case Conversion
USB Static CDC
Enable
Ignore Beep
Enable
Ignore Programming Symbol Configuration
Enable
USB Polling Interval
3 msec
USB Fast HID
Enable
IBM Specification Version
Version 2.2
HS-360X Handheld DPM Scanner User Manual
7-5
USB Host Parameters
USB Host Parameters
USB Device Type
Select the desired USB device type.
1. When changing USB device types, the scanner automatically restarts. The scanner
issues a power-up beep sequence.
2. Before selecting USB CDC Host, install the Omron Microscan USB CDC Driver on the host
to ensure the scanner does not stall during power up (due to a failure to enumerate USB).
To recover a stalled scanner:
• Install the CDC Driver.
or
• For the HS-360X Wireless Scanner, unplug the USB cable and add power. Connect
the scanner via Bluetooth and scan HID Keyboard or another host.
• For the HS-360X Wired Scanner, unplug the USB cable, while holding the trigger,
re-plug the USB cable. After 5 seconds, the scanner temporarily comes up in HID
Keyboard, scan another host.
* HID Keyboard Emulation
USB CDC Host
(Note 1)
7-6
HS-360X Handheld DPM Scanner User Manual
USB Interface
Symbol Native API (SNAPI) without
Imaging Interface
Symbol Native API (SNAPI) with Imaging
Interface
HS-360X Handheld DPM Scanner User Manual
7-7
USB Host Parameters
Symbol Native API (SNAPI) Status Handshaking
After selecting a SNAPI interface as the USB device type, select whether to enable or
disable status handshaking.
* Enable SNAPI Status Handshaking
Disable SNAPI Status Handshaking
7-8
HS-360X Handheld DPM Scanner User Manual
USB Interface
USB Keystroke Delay
This parameter sets the delay, in milliseconds, between emulated keystrokes. Scan a programming
symbol below to increase the delay when hosts require a slower transmission of data.
* No Delay
Medium Delay (20 msec)
Long Delay (40 msec)
HS-360X Handheld DPM Scanner User Manual
7-9
USB Host Parameters
USB Caps Lock Override
This option applies only to the HID Keyboard Emulation device. When enabled, the case
of the data is preserved regardless of the state of the caps lock key. This setting is always
enabled for the “Japanese, Windows (ASCII)” keyboard type and can not be disabled.
Override Caps Lock Key
(Enable)
* Do Not Override Caps Lock Key
(Disable)
7-10
HS-360X Handheld DPM Scanner User Manual
USB Interface
USB Ignore Unknown Characters
This option applies only to the HID Keyboard Emulation device and IBM device. Unknown
characters are characters the host does not recognize. When Send Barcodes With
Unknown Characters is selected, all barcode data is sent except for unknown characters,
and no error beeps sound. When Do Not Send Barcodes With Unknown Characters is
selected, barcode data is sent up to the first unknown character, then the scanner issues
an error beep.
* Send Barcodes with Unknown
Characters
Do Not Send Barcodes with Unknown
Characters
HS-360X Handheld DPM Scanner User Manual
7-11
USB Host Parameters
Emulate Keypad
When enabled, all characters are sent as ASCII sequences over the numeric keypad. For
example ASCII A would be sent as “ALT make” 0 6 5 “ALT Break.”
Disable Keypad Emulation
* Enable Keypad Emulation
7-12
HS-360X Handheld DPM Scanner User Manual
USB Interface
Emulate Keypad with Leading Zero
Enable this to send character sequences sent over the numeric keypad as ISO characters which
have a leading zero. For example ASCII A transmits as “ALT MAKE” 0 0 6 5 “ALT BREAK”.
Disable Keypad Emulation with Leading
Zero
* Enable Keypad Emulation with Leading
Zero
HS-360X Handheld DPM Scanner User Manual
7-13
USB Host Parameters
Quick Keypad Emulation
This option applies only to the HID Keyboard Emulation Device and if Emulate Keypad is
enabled. This parameter enables a quicker method of keypad emulation where ASCII
sequences are only sent for ASCII characters not found on the keyboard. The default
value is Enable.
* Enable Quick Keypad Emulation
Disable Quick Keypad Emulation
7-14
HS-360X Handheld DPM Scanner User Manual
USB Interface
USB Keyboard FN 1 Substitution
This option applies only to the USB HID Keyboard Emulation device. When enabled, this
allows replacement of any FN 1 characters in an EAN-128 barcode with a Key Category
and value chosen by the user.
Enable FN1 Substitution
* Disable FN1 Substitution
HS-360X Handheld DPM Scanner User Manual
7-15
USB Host Parameters
Function Key Mapping
ASCII values under 32 are normally sent as a control-key sequences. When this parameter
is enabled, the keys in bold are sent in place of the standard key mapping. Table entries
that do not have a bold entry remain the same whether or not this parameter is enabled.
* Disable Function Key Mapping
Enable Function Key Mapping
7-16
HS-360X Handheld DPM Scanner User Manual
USB Interface
Simulated Caps Lock
When enabled, the scanner inverts upper and lower case characters on the barcode as if
the Caps Lock state is enabled on the keyboard. This inversion is done regardless of the
current state of the keyboard’s Caps Lock state.
* Disable Simulated Caps Lock
Enable Simulated Caps Lock
HS-360X Handheld DPM Scanner User Manual
7-17
USB Host Parameters
Convert Case
When enabled, the scanner converts all barcode data to the selected case.
* No Case Conversion
Convert All to Upper Case
Convert All to Lower Case
7-18
HS-360X Handheld DPM Scanner User Manual
USB Interface
USB Static CDC
Parameter # 670
When disabled, each device connected consumes another COM port (first device = COM1,
second device = COM2, third device = COM3, etc.)
When enabled, each device connects to the same COM port.
* Enable USB Static CDC
(1)
Disable USB Static CDC
(0)
HS-360X Handheld DPM Scanner User Manual
7-19
Optional USB Parameters
Optional USB Parameters
If you configure the scanner and find the settings were not saved, or changed, when the system
is restarted scan the programming symbols that follow to override USB interface defaults.
Scan a programming symbol below after setting defaults and before configuring the scanner.
Ignore Beep
The host can send a beep request to the scanner. When this parameter is enabled, the
request is not sent to the attached scanner. All directives are still acknowledged to the
USB host as if it were processed.
Disable Ignore Beep
* Enable Ignore Beep
7-20
HS-360X Handheld DPM Scanner User Manual
USB Interface
Ignore Barcode Configuration
The host has the ability to enable/disable code types. When this parameter is enabled, the
request is not sent to the attached scanner. All directives are still acknowledged to the
USB host as if it were processed.
Disable Ignore Barcode Configuration
* Enable Ignore Barcode Configuration
HS-360X Handheld DPM Scanner User Manual
7-21
Optional USB Parameters
USB Polling Interval
Scan a programming symbol below to set the polling interval. The polling interval determines
the rate at which data can be sent between the scanner and host computer. A lower number
indicates a faster data rate.
When changing USB Device Types, the scanner automatically restarts and issues a disconnectreconnect beep sequence.
Ensure your host machine can handle the selected data rate.
1 msec
2 msec
* 3 msec
4 msec
7-22
HS-360X Handheld DPM Scanner User Manual
USB Interface
5 msec
6 msec
7 msec
8 msec
HS-360X Handheld DPM Scanner User Manual
7-23
Optional USB Parameters
9 msec
10 msec
7-24
HS-360X Handheld DPM Scanner User Manual
USB Interface
USB Fast HID
This option transmits USB HID data at a faster rate.
* Enable USB Fast HID
Disable USB Fast HID
HS-360X Handheld DPM Scanner User Manual
7-25
ASCII Character Set for USB
ASCII Character Set for USB
See Appendix H — Numeric Keyboard for the following:
• ASCII Character Set;
• ALT Key Character Set;
• GUI Key Character Set;
• F Key Character Set.
7-26
HS-360X Handheld DPM Scanner User Manual
8 RS-232 Interface
This section describes how to set up the scanner with an RS-232 host. Use the RS-232
interface to connect the scanner to a host computer or COM port.
HS-360X Handheld DPM Scanner User Manual
8-1
Introduction
Introduction
If your host does not appear in the RS-232 Host Parameters table, refer to the documentation
for the host device to set communication parameters to match the host.
The scanner uses TTL RS-232 signal levels, which interface with most system architectures.
Most computer monitors allow scanning the programming symbols directly on the screen.
When scanning from the screen, be sure to set the document magnification to a level
where you can see the programming symbol clearly, and bars and/or spaces are not merging.
8-2
HS-360X Handheld DPM Scanner User Manual
RS-232 Interface
Connecting an RS-232 Interface
Connecting HS-360X Wireless Scanner to RS-232 Interface
Connect the scanner directly to the host computer.
RS-232 Direct Connection to HS-360X Wireless Scanner
Interface cables vary depending on configuration.
Disconnect the host cables before the power supply, or the scanner may not recognize the
new host.
To connect the cradle with a RS-232 interface:
1. Connect the other end of the RS-232 interface cable to the serial port on the host.
2. Attach the modular connector of the RS-232 interface cable to the cable interface port
on the cradle.
3. If required, connect the power supply.
4. Ensure that all connections are secure.
5. Pair the scanner to the cradle by scanning the symbol on the cradle.
6. Select the RS-232 host type by scanning the appropriate programming symbol from
RS-232 Host Types.
The interface cable automatically detects the host interface type and uses the default
setting. If the default (*) does not meet your requirements, scan another host programming
symbol.
7. To modify any other parameter options, scan the appropriate programming symbols in
this chapter.
HS-360X Handheld DPM Scanner User Manual
8-3
Connecting an RS-232 Interface
Connecting the HS-360X Wired Scanner to an RS-232 Interface
Connect the scanner directly to the host computer.
Interface cable
Serial port
connector to host
Power supply
RS-232 Direct Connection to HS-360X Wired Scanner
Interface cables vary depending on configuration.
1. Attach the modular connector of the RS-232 interface cable to the cable interface port
on the scanner.
2. Connect the other end of the RS-232 interface cable to the serial port on the host.
3. Connect the power supply to the serial connector end of the RS-232 interface cable.
Plug the power supply into an appropriate outlet.
4. The scanner automatically detects the host interface type and uses the default setting.
If the default (*) does not meet your requirements, select another RS-232 host type by
scanning the appropriate programming symbol from RS-232 Host Types.
5. To modify any other parameter options, scan the appropriate programming symbols in
this chapter.
8-4
HS-360X Handheld DPM Scanner User Manual
RS-232 Interface
RS-232 Parameter Defaults
The table below lists the defaults for RS-232 host parameters. To change any option, scan
the appropriate programming symbol(s) provided in the RS-232 Host Parameters section.
Parameter
Default
RS-232 Host Parameters
RS-232 Host Types
Standard
Baud Rate
9600
Parity Type
None
Stop Bits
1 Stop Bit
Data Bits
8-Bit
Check Receive Errors
Enable
Hardware Handshaking
None
Software Handshaking
None
Host Serial Response Time-out
2 Seconds
RTS Line State
Low RTS
Beep on <BEL>
Disable
Intercharacter Delay
0 msec
Nixdorf Beep/LED Options
Normal Operation
Ignore Unknown Characters
Send Barcode
HS-360X Handheld DPM Scanner User Manual
8-5
RS-232 Parameter Defaults
RS-232 Host
To select RS-232 Host interface, scan the programming symbol below.Scanning the
Standard RS-232 symbol activates the RS-232 driver, but does not change port settings
(e.g., parity, data bits, handshaking). Selecting another RS-232 host type programming
symbol changes these settings.
* Standard RS-2321
8-6
HS-360X Handheld DPM Scanner User Manual
RS-232 Interface
Baud Rate
Baud rate is the number of bits of data transmitted per second. Set the scanner's baud
rate to match the baud rate setting of the host device. Otherwise, data may not reach the
host device or may reach it in distorted form.
Note: The scanner does not support baud rates below 9600.
* Baud Rate 9600
Baud Rate 19,200
Baud Rate 38,400
Baud Rate 57,600
Baud Rate 115,200
HS-360X Handheld DPM Scanner User Manual
8-7
RS-232 Parameter Defaults
Parity
A parity check bit is the most significant bit of each ASCII coded character. Select the
parity type according to host device requirements.
• Select Odd parity to set the parity bit value to 0 or 1, based on data, to ensure that the
coded character contains an odd number of 1 bits.
• Select Even parity to set the parity bit value is set to 0 or 1, based on data, to ensure
that the coded character contains an even number of 1 bits.
• Select None when no parity bit is required.
Odd
Even
*
8-8
None
HS-360X Handheld DPM Scanner User Manual
RS-232 Interface
Stop Bit Select
The stop bit(s) at the end of each transmitted character marks the end of transmission of
one character and prepares the receiving device for the next character in the serial data
stream. Select the number of stop bits (one or two) based on the number the receiving
terminal is programmed to accommodate. Set the number of stop bits to match host
device requirements.
* 1 Stop Bit
2 Stop Bits
HS-360X Handheld DPM Scanner User Manual
8-9
RS-232 Parameter Defaults
Data Bits
This parameter allows the scanner to interface with devices requiring a 7-bit or 8-bit ASCII protocol.
7-Bit
*
8-10
8-Bit
HS-360X Handheld DPM Scanner User Manual
RS-232 Interface
Check Receive Errors
Select whether or not to check the parity, framing, and overrun of received characters. The
parity value of received characters is verified against the parity parameter selected above.
* Check For Received Errors
Do Not Check For Received Errors
HS-360X Handheld DPM Scanner User Manual
8-11
RS-232 Parameter Defaults
Hardware Handshaking
The data interface consists of an RS-232 port designed to operate either with or without
the hardware handshaking lines, Request to Send (RTS), and Clear to Send (CTS).
Disable Standard RTS/CTS handshaking to transmit scan data as it becomes available.
Select Standard RTS/CTS handshaking to transmit scan data according to the following
sequence:
• The scanner reads the CTS line for activity. If CTS is asserted, the scanner waits up to
Host Serial Response Time-out for the host to de-assert the CTS line. If, after Host
Serial Response Time-out (default), the CTS line is still asserted, the scanner sounds a
transmit error, and discards any scanned data.
• When the CTS line is de-asserted, the scanner asserts the RTS line and waits up to
Host Serial Response Time-out for the host to assert CTS. When the host asserts CTS,
the scanner transmits data. If, after Host Serial Response Time-out (default), the CTS
line is not asserted, the scanner sounds a transmit error, and discards the data.
• When data transmission completes, the scanner de-asserts RTS 10 msec after sending
the last character.
• The host should respond by negating CTS. The scanner checks for a de-asserted CTS
upon the next transmission of data.
During the transmission of data, the CTS line should be asserted. If CTS is deasserted for
more than 50 msec between characters, the scanner aborts transmission, sounds a
transmission error, and discards the data.
If this communication sequence fails, the scanner issues an error indication. In this case,
the data is lost and must be rescanned.
If hardware handshaking and software handshaking are both enabled, hardware handshaking
takes precedence.
Note: The DTR signal is jumpered to the active state.
• None: Scan this programming symbol to disable hardware handshaking.
• Standard RTS/CTS: Scan this programming symbol to select Standard RTS/CTS
Hardware Handshaking.
• RTS/CTS Option 1: If you select RTS/CTS Option 1, the scanner asserts RTS before
transmitting and ignores the state of CTS. The scanner de-asserts RTS when the
transmission completes.
• RTS/CTS Option 2: If you select Option 2, RTS is always high or low (user-programmed
logic level). However, the scanner waits for CTS to be asserted before transmitting data.
If CTS is not asserted within Host Serial Response Time-out (default), the scanner
issues an error indication and discards the data.
• RTS/CTS Option 3: If you select Option 3, the scanner asserts RTS prior to any data
transmission, regardless of the state of CTS. The scanner waits up to Host Serial
Response Time-out (default) for CTS to be asserted. If CTS is not asserted during this
time, the scanner issues an error indication and discards the data. The scanner de-asserts
RTS when transmission is complete.
8-12
HS-360X Handheld DPM Scanner User Manual
RS-232 Interface
*
None
Standard RTS/CTS
RTS/CTS Option 1
RTS/CTS Option 2
RTS/CTS Option 3
HS-360X Handheld DPM Scanner User Manual
8-13
RS-232 Parameter Defaults
Software Handshaking
This parameter offers control of the data transmission process in addition to, or instead of,
that offered by hardware handshaking. There are five options.
If software handshaking and hardware handshaking are both enabled, hardware handshaking
takes precedence.
• None: Select this to transmit data immediately. The scanner expects no response from
the host.
• ACK/NAK: If you select this option, after transmitting data, the scanner expects either
an ACK or NAK response from the host. When it receives a NAK, the scanner transmits
the same data again and waits for either an ACK or NAK. After three unsuccessful
attempts to send data after receiving NAKs, the scanner issues an error indication and
discards the data.
The scanner waits up to the programmable Host Serial Response Time-out to receive an
ACK or NAK. If the scanner does not get a response in this time, it issues an error indication
and discards the data. There are no retries when a time-out occurs.
• ENQ: If you select this option, the scanner waits for an ENQ character from the host
before transmitting data. If it does not receive an ENQ within the Host Serial Response
Time-out, the scanner issues an error indication and discards the data. The host must
transmit an ENQ character at least every Host Serial Response Time-out to prevent
transmission errors.
• ACK/NAK with ENQ: This combines the two previous options. For re-transmissions of
data, due to a NAK from the host, an additional ENQ is not required.
• XON/XOFF: An XOFF character turns the scanner transmission off until the scanner
receives an XON character. There are two situations for XON/XOFF:
• The scanner receives an XOFF before has data to send. When the scanner has data
to send, it waits up to Host Serial Response Time-out for an XON character before
transmission. If it does not receive the XON within this time, the scanner issues an
error indication and discards the data.
• The scanner receives an XOFF during a transmission. Data transmission then stops
after sending the current byte. When the scanner receives an XON character, it sends
the rest of the data message. The scanner waits indefinitely for the XON.
8-14
HS-360X Handheld DPM Scanner User Manual
RS-232 Interface
* None
ACK/NAK
ENQ
ACK/NAK with ENQ
XON/XOFF
HS-360X Handheld DPM Scanner User Manual
8-15
RS-232 Parameter Defaults
Host Serial Response Timeout
This parameter specifies how long the scanner waits for an ACK, NAK, or CTS before
determining that a transmission error occurred. This only applies when in one of the ACK/NAK
software handshaking modes, or RTS/CTS hardware handshaking mode.
* Minimum: 2 Seconds
Low: 2.5 Seconds
Medium: 5 Seconds
High: 7.5 Seconds
Maximum: 9.9 Seconds
8-16
HS-360X Handheld DPM Scanner User Manual
RS-232 Interface
RTS Line State
This parameter sets the idle state of the Serial Host RTS line. Scan a programming symbol
below to select Low RTS or High RTS line state.
* Host: Low RTS
Host: High RTS
HS-360X Handheld DPM Scanner User Manual
8-17
RS-232 Parameter Defaults
Beep on <BEL>
If you enable this parameter, the scanner issues a beep when it detects a <BEL> character
on the RS-232 serial line. <BEL> indicates an illegal entry or other important event.
Beep On <BEL> Character
(Enable)
* Do Not Beep On <BEL> Character
(Disable)
8-18
HS-360X Handheld DPM Scanner User Manual
RS-232 Interface
Intercharacter Delay
This parameter specifies the intercharacter delay inserted between character transmissions.
* Minimum: 0 msec
Low: 25 msec
Medium: 50 msec
High: 75 msec
Maximum: 99 msec
HS-360X Handheld DPM Scanner User Manual
8-19
RS-232 Parameter Defaults
Ignore Unknown Characters
Unknown characters are characters the host does not recognize. Select Send Barcode
with Unknown Characters to send all barcode data except for unknown characters. The
scanner issues no error beeps.
Select Do Not Send Barcodes With Unknown Characters to send barcode data up to
the first unknown character. The scanner issues an error beep.
* Send Barcode
(with unknown characters)
Do Not Send Barcodes
(with unknown characters)
8-20
HS-360X Handheld DPM Scanner User Manual
RS-232 Interface
ASCII Character Set for RS-232
See Appendix I — ASCII Character Sets for Prefix/Suffix values.
HS-360X Handheld DPM Scanner User Manual
8-21
ASCII Character Set for RS-232
8-22
HS-360X Handheld DPM Scanner User Manual
9 Symbologies
This section describes symbology features and provides programming symbols for selecting
those features.
To set feature parameters, scan a single programming symbol or a short barcode sequence.
The settings are stored in non-volatile memory and are preserved even when the scanner
powers down.
HS-360X Handheld DPM Scanner User Manual
9-1
Introduction
Introduction
Most computer monitors allow scanning the programming symbols directly on the screen.
When scanning from the screen, be sure to set the document magnification to a level
where you can see the programming symbol clearly, and bars and/or spaces do not
merge.
Select a host type (see each host chapter for specific host information) after the power-up
beeps sound. This is only necessary upon the first power-up when connected to a new host.
Scanning Sequence Examples
In most cases, scanning one programming symbol sets the parameter value. For example,
to transmit barcode data without the UPC-A check digit, simply scan the Do Not Transmit
UPC-A Check Digit programming symbol under Transmit UPC-A Check Digit. The
scanner issues a fast warble beep and the LED turns green, signifying a successful
parameter entry.
Other parameters, such as Set Length(s) for D 2 of 5 require scanning several programming
symbols. See the individual parameter, such as Set Length(s) for D 2 of 5, for this procedure.
Errors While Scanning
Unless otherwise specified, to correct an error during a scanning sequence, just re-scan
the correct parameter.
9-2
HS-360X Handheld DPM Scanner User Manual
Symbologies
Symbology Parameter Defaults
The table below lists the defaults for all symbology parameters. To change the default
values, scan the appropriate programming symbols in this guide. These new values
replace the standard default values in memory.
Parameter
Number
Default
UPC-A
1
Enable
UPC-E
2
Enable
UPC-E1
12
Disable
Parameter
Enable/Disable All Code Types
1D Symbologies
UPC/EAN
EAN-8/JAN 8
4
Enable
EAN-13/JAN 13
3
Enable
Bookland EAN
83
Disable
Decode UPC/EAN/JAN Supplementals
(2 and 5 digits)
16
Ignore
User-Programmable Supplementals
Supplemental 1:
Supplemental 2:
579
580
000
UPC/EAN/JAN Supplemental Redundancy
80
10
Decode UPC/EAN/JAN Supplemental
AIM ID
672
Combined
UPC Reduced Quiet Zone
1289
Disable
Transmit UPC-A Check Digit
40
Enable
Transmit UPC-E Check Digit
41
Enable
Transmit UPC-E1 Check Digit
42
Enable
UPC-A Preamble
34
System Character
UPC-E Preamble
35
System Character
UPC-E1 Preamble
36
System Character
Convert UPC-E to A
37
Disable
Convert UPC-E1 to A
38
Disable
EAN-8/JAN-8 Extend
39
Disable
Bookland ISBN Format
576
ISBN-10
UCC Coupon Extended Code
85
Disable
Coupon Report
730
New Coupon Format
ISSN EAN
617
Disable
8
Enable
Code 128
Code 128
HS-360X Handheld DPM Scanner User Manual
9-3
Symbology Parameter Defaults
Parameter
Parameter
Number
Default
Set Length(s) for Code 128
209, 210
1 to 55
GS1-128 (formerly UCC/EAN-128)
14
Enable
ISBT 128
84
Disable
ISBT Concatenation
577
Autodiscriminate
Check ISBT Table
578
Enable
ISBT Concatenation Redundancy
223
10
Code 128 Security Level
751
Security Level 1
Code 128 Reduced Quiet Zone
1208
Disable
Ignore Code 128 <FNC4>
1254
Disable
Code 39
0
Enable
Trioptic Code 39
13
Disable
Convert Code 39 to Code 32
(Italian Pharmacy Code)
86
Disable
Code 39
Code 32 Prefix
231
Disable
Set Length(s) for Code 39
18, 19
1 to 55
Code 39 Check Digit Verification
48
Disable
Transmit Code 39 Check Digit
43
Disable
Code 39 Full ASCII Conversion
17
Disable
Code 39 Security Level
750
Security Level 1
Code 39 Reduced Quiet Zone
1209
Disable
Code 93
9
Enable
Set Length(s) for Code 93
26, 27
1 to 55
Code 93
Code 11
Code 11
10
Disable
Set Lengths for Code 11
28, 29
4 to 55
Code 11 Check Digit Verification
52
Disable
Transmit Code 11 Check Digit(s)
47
Disable
Interleaved 2 of 5 (ITF)
Interleaved 2 of 5 (ITF)
6
Disable
Set Lengths for I 2 of 5
22, 23
6 to 55
I 2 of 5 Check Digit Verification
49
Disable
Transmit I 2 of 5 Check Digit
44
Disable
Convert I 2 of 5 to EAN 13
82
Disable
9-4
HS-360X Handheld DPM Scanner User Manual
Symbologies
Parameter
Number
Default
I 2 of 5 Security Level
1121
Security Level 1
I 2 of 5 Reduced Quiet Zone
1210
Disable
Discrete 2 of 5
5
Disable
Set Length(s) for D 2 of 5
20, 21
1 to 55
Codabar
7
Enable
Set Lengths for Codabar
24, 25
4 to 55
CLSI Editing
54
Disable
NOTIS Editing
55
Disable
Codabar Upper or Lower Case Start/
Stop Characters Detection
855
Upper Case
11
Disable
Parameter
Discrete 2 of 5 (DTF)
Codabar (NW - 7)
MSI
MSI
Set Length(s) for MSI
30, 31
4 to 55
MSI Check Digits
50
One
Transmit MSI Check Digit
46
Disable
MSI Check Digit Algorithm
51
Mod 10/Mod 10
408
Disable
Matrix 2 of 5
618
Disable
Matrix 2 of 5 Lengths
619
620
4 to 55
Matrix 2 of 5 Check Digit
622
Disable
Transmit Matrix 2 of 5 Check Digit
623
Disable
Korean 3 of 5
581
Disable
Inverse 1D
586
Regular
Chinese 2 of 5
Chinese 2 of 5
Matrix 2 of 5
Korean 3 of 5
GS1 DataBar
GS1 DataBar-14
338
Enable
GS1 DataBar Limited
339
Enable
GS1 DataBar Expanded
340
Enable
Convert GS1 DataBar to UPC/EAN
397
Disable
GS1 DataBar Limited Security Level
728
Level 3
HS-360X Handheld DPM Scanner User Manual
9-5
Symbology Parameter Defaults
Parameter
Number
Default
Composite CC-C
341
Disable
Composite CC-A/B
342
Disable
Composite TLC-39
371
Disable
UPC Composite Mode
344
UPC Never Linked
Composite Beep Mode
398
Beep As Each Code Type is
Decoded
GS1-128 Emulation Mode for UCC/EAN Composite
Codes
427
Disable
Parameter
Composite
2D Symbologies
PDF417
15
Enable
MicroPDF417
227
Disable
Code 128 Emulation
123
Disable
Data Matrix
292
Enable
GS1 Data Matrix
1336
Disable
Data Matrix Inverse
588
Inverse Autodetect
Maxicode
294
Disable
QR Code
293
Enable
GS1 QR
1343
Disable
MicroQR
573
Enable
Aztec
574
Enable
Aztec Inverse
589
Inverse Autodetect
Han Xin
1167
Disable
Han Xin Inverse
1168
Regular
US Postnet
89
Disable
US Planet
90
Disable
Transmit US Postal Check Digit
95
Enable
Postal Codes
UK Postal
91
Disable
Transmit UK Postal Check Digit
96
Enable
Japan Postal
290
Disable
Australia Post
291
Disable
Australia Post Format
718
Autodiscriminate
Netherlands KIX Code
326
Disable
USPS 4CB/One Code/Intelligent Mail
592
Disable
UPU FICS Postal
611
Disable
Mailmark
1337
Disable
9-6
HS-360X Handheld DPM Scanner User Manual
Symbologies
Parameter
Number
Default
Redundancy Level
78
1
Security Level
77
1
1D Quiet Zone Level
1288
1
Intercharacter Gap Size
381
Normal
Flush Macro PDF Buffer
N/A
N/A
Abort Macro PDF Entry
N/A
N/A
Parameter
Symbology-Specific Security Levels
Report Version
Macro PDF
HS-360X Handheld DPM Scanner User Manual
9-7
Enable/Disable All Code Types
Enable/Disable All Code Types
To disable all symbologies, scan Disable All Code Types below. This is useful when
enabling only a few code types.
Scan Enable All Code Types turn on (enable) all code types. This is useful when you
want to read all codes, or when you want to disable only a few code types.
Disable All Code Types
Enable All Code Types
9-8
HS-360X Handheld DPM Scanner User Manual
Symbologies
UPC/EAN
Enable/Disable UPC-A
Parameter # 1
To enable or disable UPC-A, scan the appropriate programming symbol below.
* Enable UPC-A
(1)
Disable UPC-A
(0)
HS-360X Handheld DPM Scanner User Manual
9-9
UPC/EAN
Enable/Disable UPC-E
Parameter # 2
To enable or disable UPC-E, scan the appropriate programming symbol below.
* Enable UPC-E
(1)
Disable UPC-E
(0)
9-10
HS-360X Handheld DPM Scanner User Manual
Symbologies
Enable/Disable UPC-E1
Parameter # 12
UPC-E1 is disabled by default.
To enable or disable UPC-E1, scan the appropriate programming symbol below.
UPC-E1 is not a UCC (Uniform Code Council) approved symbology.
Enable UPC-E1
(1)
* Disable UPC-E1
(0)
HS-360X Handheld DPM Scanner User Manual
9-11
UPC/EAN
Enable/Disable EAN-8/JAN-8
Parameter # 4
To enable or disable EAN-8/JAN-8, scan the appropriate programming symbol below.
* Enable EAN-8/JAN-8
(1)
Disable EAN-8/JAN-8
(0)
9-12
HS-360X Handheld DPM Scanner User Manual
Symbologies
Enable/Disable EAN-13/JAN-13
Parameter # 3
To enable or disable EAN-13/JAN-13, scan the appropriate programming symbol below.
* Enable EAN-13/JAN-13
(1)
Disable EAN-13/JAN-13
(0)
HS-360X Handheld DPM Scanner User Manual
9-13
UPC/EAN
Enable/Disable Bookland EAN
Parameter # 83
To enable or disable Bookland EAN, scan the appropriate programming symbol below.
If you enable Bookland EAN, select Bookland ISBN Format. Also select either Decode
UPC/EAN Supplementals, Autodiscriminate UPC/EAN Supplementals, or Enable 978/979
Supplemental Mode in Decode UPC/EAN/JAN Supplementals.
Enable Bookland EAN
(1)
* Disable Bookland EAN
(0)
9-14
HS-360X Handheld DPM Scanner User Manual
Symbologies
Decode UPC/EAN/JAN Supplementals
Parameter # 16
Supplementals are appended according to specific format conventions (e.g., UPC A+2,
UPC E+2, EAN 13+2). The following options are available:
• If you select Ignore UPC/EAN with Supplementals, and the scanner is presented
with a UPC/EAN plus supplemental symbol, the scanner decodes UPC/EAN and
ignores the supplemental characters.
• If you select Decode UPC/EAN with Supplementals, the scanner only decodes UPC/EAN
symbols with supplemental characters, and ignores symbols without supplementals.
• If you select Autodiscriminate UPC/EAN Supplementals, the scanner decodes
UPC/EAN symbols with supplemental characters immediately. If the symbol does not
have a supplemental, the scanner must decode the barcode the number of times set via
UPC/EAN/JAN Supplemental Redundancy before transmitting its data to confirm that
there is no supplemental.
• If you select one of the following Supplemental Mode options, the scanner immediately
transmits EAN-13 barcodes starting with that prefix that have supplemental characters. If
the symbol does not have a supplemental, the scanner must decode the barcode the
number of times set via UPC/EAN/JAN Supplemental Redundancy before transmitting
its data to confirm that there is no supplemental. The scanner transmits UPC/EAN barcodes
that do not have that prefix immediately.
• Enable 378/379 Supplemental Mode
• Enable 978/979 Supplemental Mode
• Enable 977 Supplemental Mode
• Enable 414/419/434/439 Supplemental Mode
• Enable 491 Supplemental Mode
• Enable Smart Supplemental Mode - applies to EAN-13 barcodes starting with any
prefix listed previously.
• Supplemental User-Programmable Type 1 applies to EAN-13 barcodes starting
with a 3-digit user-defined prefix. Set this 3-digit prefix using User-Programmable
Supplementals.
• Supplemental User-Programmable Type 1 and 2 applies to EAN-13 barcodes
starting with either of two 3-digit user-defined prefixes. Set the 3-digit prefixes using
User-Programmable Supplementals.
• Smart Supplemental Plus User-Programmable 1 applies to EAN-13 barcodes starting
with any prefix listed previously or the user-defined prefix set using User-Programmable
Supplementals.
• Smart Supplemental Plus User-Programmable 1 and 2 applies to EAN-13
barcodes starting with any prefix listed previously or one of the two user-defined
prefixes set using User-Programmable Supplementals.
Note: To minimize the risk of invalid data transmission, select either to decode or
ignore supplemental characters.
HS-360X Handheld DPM Scanner User Manual
9-15
UPC/EAN
Decode UPC/EAN/JAN Only With
Supplementals
(1)
* Ignore Supplementals
(0)
Autodiscriminate UPC/EAN/JAN
Supplementals
(2)
Enable 378/379 Supplemental Mode
(4)
Enable 978/979 Supplemental Mode
(5)
9-16
HS-360X Handheld DPM Scanner User Manual
Symbologies
Enable 977 Supplemental Mode
(7)
Enable 414/419/434/439 Supplemental
Mode
(6)
Enable 491 Supplemental Mode
(8)
Enable Smart Supplemental Mode
(3)
Supplemental User-Programmable Type 1
(9)
HS-360X Handheld DPM Scanner User Manual
9-17
UPC/EAN
Supplemental User-Programmable Type 1
and 2
(10)
Smart Supplemental Plus UserProgrammable 1
(11)
Smart Supplemental Plus UserProgrammable 1 and 2
(12)
9-18
HS-360X Handheld DPM Scanner User Manual
Symbologies
User-Programmable Supplementals
Supplemental 1: Parameter # 579
Supplemental 2: Parameter # 580
If you selected a Supplemental User-Programmable option from Decode UPC/EAN/JAN
Supplementals, select User-Programmable Supplemental 1 to set the 3-digit prefix.
Then select the 3 digits using the numeric programming symbols. Select User-Programmable
Supplemental 2 to set a second 3-digit prefix. Then select the 3 digits using the numeric
programming symbols . The default is 000 (zeroes).
User-Programmable Supplemental 1
User-Programmable Supplemental 2
HS-360X Handheld DPM Scanner User Manual
9-19
UPC/EAN
UPC/EAN/JAN Supplemental Redundancy
Parameter # 80
If you selected Autodiscriminate UPC/EAN/JAN Supplementals, this option adjusts the
number of times to decode a symbol without supplementals before transmission. The
range is from two to thirty times. Five or above is recommended when decoding a mix of
UPC/EAN/JAN symbols with and without supplementals. The default is 10.
Scan the programming symbol below to set a decode redundancy value. Next, scan two
numeric programming symbols in Appendix H — Numeric Keyboard. Enter a leading
zero for single digit numbers.
UPC/EAN/JAN Supplemental
Redundancy
9-20
HS-360X Handheld DPM Scanner User Manual
Symbologies
UPC/EAN/JAN Supplemental AIM ID Format
Parameter # 672
Select an output format when reporting UPC/EAN/JAN barcodes with Supplementals
using AIM Code ID Character:
• Separate - transmit UPC/EAN with supplementals with separate AIM IDs but one
transmission, i.e.:
]E<0 or 4><data>]E<1 or 2>[supplemental data]
• Combined – transmit UPC/EAN with supplementals with one AIM ID and one transmission, i.e.:
]E3<data+supplemental data>
• Separate Transmissions - transmit UPC/EAN with supplementals with separate AIM
IDs and separate transmissions, i.e.:
]E<0 or 4><data>
]E<1 or 2>[supplemental data]
Separate
(0)
* Combined
(1)
Separate Transmissions
(2)
HS-360X Handheld DPM Scanner User Manual
9-21
UPC/EAN
UPC Reduced Quiet Zone
Parameter # 1289
Scan one of the following programming symbols to enable or disable decoding UPC barcodes
with reduced quiet zones. If you select Enable, select 1D Quiet Zone.
Enable UPC Reduced Quiet Zone
(1)
* Disable UPC Reduced Quiet Zone
(0)
9-22
HS-360X Handheld DPM Scanner User Manual
Symbologies
Transmit UPC-A Check Digit
Parameter # 40
The check digit is the last character of the symbol used to verify the integrity of the data.
Scan the appropriate programming symbol below to transmit the barcode data with or
without the UPC-A check digit. It is always verified to guarantee the integrity of the data.
* Transmit UPC-A Check Digit
(1)
Do Not Transmit UPC-A Check Digit
(0)
HS-360X Handheld DPM Scanner User Manual
9-23
UPC/EAN
Transmit UPC-E Check Digit
Parameter # 41
The check digit is the last character of the symbol used to verify the integrity of the data.
Scan the appropriate programming symbol below to transmit the barcode data with or
without the UPC-E check digit. It is always verified to guarantee the integrity of the data.
* Transmit UPC-E Check Digit
(1)
Do Not Transmit UPC-E Check Digit
(0)
9-24
HS-360X Handheld DPM Scanner User Manual
Symbologies
Transmit UPC-E1 Check Digit
Parameter # 42
The check digit is the last character of the symbol used to verify the integrity of the data.
Scan the appropriate programming symbol below to transmit the barcode data with or
without the UPC-E1 check digit. It is always verified to guarantee the integrity of the data.
* Transmit UPC-E1 Check Digit
(1)
Do Not Transmit UPC-E1 Check Digit
(0)
HS-360X Handheld DPM Scanner User Manual
9-25
UPC/EAN
UPC-A Preamble
Parameter # 34
Preamble characters are part of the UPC symbol, and include Country Code and System
Character. There are three options for transmitting a UPC-A preamble to the host device:
transmit System Character only, transmit System Character and Country Code (“0” for
USA), and transmit no preamble. Select the appropriate option to match the host system.
No Preamble (<DATA>)
(0)
* System Character (<SYSTEM
CHARACTER> <DATA>)
(1)
System Character & Country Code
(< COUNTRY CODE> <SYSTEM
CHARACTER> <DATA>)
(2)
9-26
HS-360X Handheld DPM Scanner User Manual
Symbologies
UPC-E Preamble
Parameter # 35
Preamble characters are part of the UPC symbol, and include Country Code and System
Character. There are three options for transmitting a UPC-E preamble to the host device:
transmit System Character only, transmit System Character and Country Code (“0” for
USA), and transmit no preamble. Select the appropriate option to match the host system.
No Preamble (<DATA>)
(0)
* System Character (<SYSTEM
CHARACTER> <DATA>)
(1)
System Character & Country Code
(< COUNTRY CODE> <SYSTEM
CHARACTER> <DATA>)
(2)
HS-360X Handheld DPM Scanner User Manual
9-27
UPC/EAN
UPC-E1 Preamble
Parameter # 36
Preamble characters are part of the UPC symbol, and include Country Code and System
Character. There are three options for transmitting a UPC-E1 preamble to the host device:
transmit System Character only, transmit System Character and Country Code (“0” for
USA), and transmit no preamble. Select the appropriate option to match the host system.
No Preamble (<DATA>)
(0)
* System Character (<SYSTEM
CHARACTER> <DATA>)
(1)
System Character & Country Code
(< COUNTRY CODE> <SYSTEM
CHARACTER> <DATA>)
(2)
9-28
HS-360X Handheld DPM Scanner User Manual
Symbologies
Convert UPC-E to UPC-A
Parameter # 37
Enable this to convert UPC-E (zero suppressed) decoded data to UPC-A format before
transmission. After conversion, the data follows UPC-A format and is affected by UPC-A
programming selections (e.g., Preamble, Check Digit).
Disable this to transmit UPC-E decoded data as UPC-E data, without conversion.
Convert UPC-E to UPC-A (Enable)
(1)
* Do Not Convert UPC-E to UPC-A
(Disable)
(0)
HS-360X Handheld DPM Scanner User Manual
9-29
UPC/EAN
Convert UPC-E1 to UPC-A
Parameter # 38
Enable this to convert UPC-E1 decoded data to UPC-A format before transmission. After
conversion, the data follows UPC-A format and is affected by UPC-A programming
selections (e.g., Preamble, Check Digit).
Disable this to transmit UPC-E1 decoded data as UPC-E1 data, without conversion.
Convert UPC-E1 to UPC-A (Enable)
(1)
* Do Not Convert UPC-E1 to UPC-A
(Disable)
(0)
9-30
HS-360X Handheld DPM Scanner User Manual
Symbologies
EAN-8/JAN-8 Extend
Parameter # 39
Enable this parameter to add five leading zeros to decoded EAN-8 symbols to make them
compatible in format to EAN-13 symbols. Disable this to transmit EAN-8 symbols as is.
Enable EAN/JAN Zero Extend
(1)
* Disable EAN/JAN Zero Extend
(0)
HS-360X Handheld DPM Scanner User Manual
9-31
UPC/EAN
Bookland ISBN Format
Parameter # 576
If you enabled Bookland EAN using Enable/Disable Bookland EAN, select one of the
following formats for Bookland data:
• Bookland ISBN-10 - The scanner reports Bookland data starting with 978 in traditional
10-digit format with the special Bookland check digit for backward-compatibility. Data
starting with 979 is not considered Bookland in this mode.
• Bookland ISBN-13 - The scanner reports Bookland data (starting with either 978 or
979) as EAN-13 in 13-digit format to meet the 2007 ISBN-13 protocol.
* Bookland ISBN-10
(0)
Bookland ISBN-13
(1)
For Bookland EAN to function properly, first enable Bookland EAN using Enable/Disable
Bookland EAN, then select either Decode UPC/EAN Supplementals, Autodiscriminate
UPC/EAN Supplementals, or Enable 978/979 Supplemental Mode in Decode UPC/EAN/JAN
Supplementals.
9-32
HS-360X Handheld DPM Scanner User Manual
Symbologies
UCC Coupon Extended Code
Parameter # 85
Enable this parameter to decode UPC-A barcodes starting with digit ‘5’, EAN-13 barcodes
starting with digit ‘99’, and UPC-A/GS1-128 Coupon Codes. UPCA, EAN-13, and GS1-128
must be enabled to scan all types of Coupon Codes.
Enable UCC Coupon Extended Code
(1)
* Disable UCC Coupon Extended Code
(0)
See UPC/EAN/JAN Supplemental Redundancy to control autodiscrimination of the
GS1-128 (right half) of a coupon code.
HS-360X Handheld DPM Scanner User Manual
9-33
UPC/EAN
Coupon Report
Parameter # 730
Select an option to determine which type of coupon format to support.
• Select Old Coupon Format to support UPC-A/GS1-128 and EAN-13/GS1-128.
• Select New Coupon Format as an interim format to support UPC-A/GS1-DataBar and
EAN-13/GS1-DataBar.
• If you select Autodiscriminate Format, the scanner supports both Old Coupon Format
and New Coupon Format.
Old Coupon Format
(0)
* New Coupon Format
(1)
Autodiscriminate Coupon Format
(2)
9-34
HS-360X Handheld DPM Scanner User Manual
Symbologies
ISSN EAN
Parameter # 617
To enable or disable ISSN EAN, scan the appropriate programming symbol below.
Enable ISSN EAN
(1)
* Disable ISSN EAN
(0)
HS-360X Handheld DPM Scanner User Manual
9-35
Code 128
Code 128
Enable/Disable Code 128
Parameter # 8
To enable or disable Code 128, scan the appropriate programming symbol below.
* Enable Code 128
(1)
Disable Code 128
(0)
9-36
HS-360X Handheld DPM Scanner User Manual
Symbologies
Set Lengths for Code 128
Parameter # L1 = 209, L2 = 210
The length of a code refers to the number of characters (i.e., human readable characters),
including check digit(s) the code contains. Set lengths for Code 128 to any length, one or
two discrete lengths, or lengths within a specific range. The default is 1 to 55.
When setting lengths for different barcode types, enter a leading zero for single digit numbers.
• One Discrete Length - Select this option to decode only Code 128 symbols containing
a selected length. Select the length using the numeric programming symbols in
Appendix H — Numeric Keyboard. For example, to decode only Code 128 symbols
with 14 characters, scan Code 128 - One Discrete Length, then scan 1 followed by 4.
• Two Discrete Lengths - Select this option to decode only Code 128 symbols containing
either of two selected lengths. Select lengths using the numeric programming symbols
in Appendix H — Numeric Keyboard. For example, to decode only Code 128 symbols
containing either 2 or 14 characters, select Code 128 - Two Discrete Lengths, then
scan 0, 2, 1, and then 4.
• Length Within Range - Select this option to decode a Code 128 symbol with a specific
length range. Select lengths using numeric programming symbols in Appendix H —
Numeric Keyboard. For example, to decode Code 128 symbols containing between 4
and 12 characters, first scan Code 128 - Length Within Range. Then scan 0, 4, 1, and
2 (enter a leading zero for single digit numbers).
• Any Length - Select this option to decode Code 128 symbols containing any number of
characters within the scanner’s capability.
Code 128 - One Discrete Length
Code 128 - Two Discrete Lengths
HS-360X Handheld DPM Scanner User Manual
9-37
Code 128
Code 128 - Length Within Range
Code 128 - Any Length
9-38
HS-360X Handheld DPM Scanner User Manual
Symbologies
Enable/Disable GS1-128 (formerly UCC/EAN-128)
Parameter # 14
To enable or disable GS1-128, scan the appropriate programming symbol below.
* Enable GS1-128
(1)
Disable GS1-128
(0)
HS-360X Handheld DPM Scanner User Manual
9-39
Code 128
Enable/Disable ISBT 128
Parameter # 84
ISBT 128 is a variant of Code 128 used in the blood bank industry. Scan a programming
symbol below to enable or disable ISBT 128. If necessary, the host must perform concatenation
of the ISBT data.
Enable ISBT 128
(1)
* Disable ISBT 128
(0)
9-40
HS-360X Handheld DPM Scanner User Manual
Symbologies
ISBT Concatenation
Parameter # 577
Select an option for concatenating pairs of ISBT code types:
• If you select Disable ISBT Concatenation, the scanner does not concatenate pairs
of ISBT codes it encounters.
• If you select Enable ISBT Concatenation, there must be two ISBT codes in order for
the scanner to decode and perform concatenation. The scanner does not decode single
ISBT symbols.
• If you select Autodiscriminate ISBT Concatenation, the scanner decodes and concatenates
pairs of ISBT codes immediately. If only a single ISBT symbol is present, the scanner
must decode the symbol the number of times set via ISBT Concatenation Redundancy
before transmitting its data to confirm that there is no additional ISBT symbol.
Disable ISBT Concatenation
(0)
Enable ISBT Concatenation
(1)
* Autodiscriminate ISBT Concatenation
(2)
HS-360X Handheld DPM Scanner User Manual
9-41
Code 128
Check ISBT Table
Parameter # 578
The ISBT specification includes a table that lists several types of ISBT barcodes that are
commonly used in pairs. If you set ISBT Concatenation to Enable, enable Check ISBT
Table to concatenate only those pairs found in this table. Other types of ISBT codes are
not concatenated.
* Enable Check ISBT Table
(1)
Disable Check ISBT Table
(0)
9-42
HS-360X Handheld DPM Scanner User Manual
Symbologies
ISBT Concatenation Redundancy
Parameter # 223
If you set ISBT Concatenation to Autodiscriminate, use this parameter to set the number
of times the scanner must decode an ISBT symbol before determining that there is no
additional symbol.
Scan the programming symbol below, then scan two numeric programming symbols in
Appendix H — Numeric Keyboard to set a value between 2 and 20. Enter a leading zero
for single digit numbers.
ISBT Concatenation Redundancy
HS-360X Handheld DPM Scanner User Manual
9-43
Code 128
Code 128 Security Level
Parameter # 751
Code 128 barcodes are vulnerable to misdecodes, particularly when Code 128 Lengths is
set to Any Length. The scanner offers four levels of decode security for Code 128 barcodes.
There is an inverse relationship between security and scanner aggressiveness. Increasing
the level of security can reduce scanning aggressiveness, so select only the level of
security necessary.
• Code 128 Security Level 0: This setting allows the scanner to operate in its most
aggressive state, while providing sufficient security in decoding most in-spec barcodes.
• Code 128 Security Level 1: A barcode must be successfully read twice, and satisfy
certain safety requirements before being decoded. This default setting eliminates most
misdecodes.
• Code 128 Security Level 2: Select this option with greater barcode security requirements
if Security Level 1 fails to eliminate misdecodes.
• Code 128 Security Level 3: If you selected Security Level 2, and misdecodes still
occur, select this security level to apply the highest safety requirements. A barcode must
be successfully read three times before being decoded.
Note: Selecting this option is an extreme measure against mis-decoding severely out-of-spec
barcodes. Selecting this level of security significantly impairs the decoding ability of the
scanner. If this level of security is required, try to improve the quality of the barcodes.
Code 128 Security Level 0
(0)
* Code 128 Security Level 1
(1)
9-44
Code 128 Security Level 2
(2)
HS-360X Handheld DPM Scanner User Manual
Symbologies
Code 128 Security Level 3
(3)
HS-360X Handheld DPM Scanner User Manual
9-45
Code 128
Code 128 Reduced Quiet Zone
Parameter # 1208
Scan one of the following programming symbols to enable or disable decoding Code 128
barcodes with reduced quiet zones. If you select Enable, select 1D Quiet Zone Level.
Enable Code 128 Reduced Quiet Zone
(1)
* Disable Code 128 Reduced Quiet Zone
(0)
9-46
HS-360X Handheld DPM Scanner User Manual
Symbologies
Ignore Code 128 <FNC4>
Parameter # 1254
This feature applies to Code 128 barcodes with an embedded <FNC4> character. Enable
this to strip the <FNC4> character from the decode data. The remaining characters are
sent to the host unchanged. When disabled, the <FNC4> character is processed normally
as per Code 128 standard.
Enable Ignore Code 128 <FNC4>
(1)
* Disable Ignore Code 128 <FNC4>
(0)
HS-360X Handheld DPM Scanner User Manual
9-47
Code 39
Code 39
Enable/Disable Code 39
Parameter # 0
To enable or disable Code 39, scan the appropriate programming symbol below.
* Enable Code 39
(1)
Disable Code 39
(0)
9-48
HS-360X Handheld DPM Scanner User Manual
Symbologies
Enable/Disable Trioptic Code 39
Parameter # 13
Trioptic Code 39 is a variant of Code 39 used in the marking of computer tape cartridges.
Trioptic Code 39 symbols always contain six characters. To enable or disable Trioptic
Code 39, scan the appropriate programming symbol below.
Note: You cannot enable Trioptic Code 39 and Code 39 Full ASCII simultaneously.
Enable Trioptic Code 39
(1)
* Disable Trioptic Code 39
(0)
HS-360X Handheld DPM Scanner User Manual
9-49
Code 39
Convert Code 39 to Code 32
Parameter # 86
Code 32 is a variant of Code 39 used by the Italian pharmaceutical industry. Scan the
appropriate programming symbol below to enable or disable converting Code 39 to Code 32.
Code 39 must be enabled for this parameter to function.
Enable Convert Code 39 to Code 32
(1)
* Disable Convert Code 39 to Code 32
(0)
9-50
HS-360X Handheld DPM Scanner User Manual
Symbologies
Code 32 Prefix
Parameter # 231
Scan the appropriate programming symbol below to enable or disable adding the prefix
character “A” to all Code 32 barcodes.
Convert Code 39 to Code 32 must be enabled for this parameter to function.
Enable Code 32 Prefix
(1)
* Disable Code 32 Prefix
(0)
HS-360X Handheld DPM Scanner User Manual
9-51
Code 39
Set Lengths for Code 39
Parameter # L1 = 18, L2 = 19
The length of a code refers to the number of characters (i.e., human readable characters),
including check digit(s) the code contains. Set lengths for Code 39 to any length, one or
two discrete lengths, or lengths within a specific range. If Code 39 Full ASCII is enabled,
Length Within a Range or Any Length are the preferred options. The default is 1 to 55.
When setting lengths for different barcode types, enter a leading zero for single digit numbers.
• One Discrete Length - Select this option to decode only Code 39 symbols containing a
selected length. Select the length using the numeric programming symbols in
Appendix H — Numeric Keyboard. For example, to decode only Code 39 symbols
with 14 characters, scan Code 39 - One Discrete Length, then scan 1 followed by 4.
• Two Discrete Lengths - Select this option to decode only Code 39 symbols containing
either of two selected lengths. Select lengths using the numeric programming symbols
in Appendix H — Numeric Keyboard. For example, to decode only Code 39 symbols
containing either 2 or 14 characters, select Code 39 - Two Discrete Lengths, then scan
0, 2, 1, and then 4.
• Length Within Range - Select this option to decode a Code 39 symbol with a specific
length range. Select lengths using numeric programming symbols in Appendix H —
Numeric Keyboard. For example, to decode Code 39 symbols containing between 4
and 12 characters, first scan Code 39 - Length Within Range. Then scan 0, 4, 1, and 2
(enter a leading zero for single digit numbers).
• Any Length - Select this option to decode Code 39 symbols containing any number of
characters within the scanner’s capability.
Code 39 - One Discrete Length
Code 39 - Two Discrete Lengths
Code 39 - Length Within Range
9-52
HS-360X Handheld DPM Scanner User Manual
Symbologies
Code 39 - Any Length
HS-360X Handheld DPM Scanner User Manual
9-53
Code 39
Code 39 Check Digit Verification
Parameter # 48
Enable this feature to check the integrity of all Code 39 symbols to verify that the data
complies with specified check digit algorithm. Only Code 39 symbols which include a
Modulo 43 check digit are decoded. Enable this feature if the Code 39 symbols contain a
Modulo 43 check digit.
Enable Code 39 Check Digit
(1)
* Disable Code 39 Check Digit
(0)
9-54
HS-360X Handheld DPM Scanner User Manual
Symbologies
Transmit Code 39 Check Digit
Parameter # 43
Scan a programming symbol below to transmit Code 39 data with or without the check digit.
Code 39 Check Digit Verification must be enabled for this parameter to function.
Transmit Code 39 Check Digit (Enable)
(1)
* Do Not Transmit Code 39 Check Digit
(Disable)
(0)
HS-360X Handheld DPM Scanner User Manual
9-55
Code 39
Code 39 Full ASCII Conversion
Parameter # 17
Code 39 Full ASCII is a variant of Code 39 which pairs characters to encode the full ASCII
character set. To enable or disable Code 39 Full ASCII, scan the appropriate programming
symbol below.
You cannot enable Trioptic Code 39 and Code 39 Full ASCII simultaneously.
Code 39 Full ASCII to Full ASCII Correlation is host-dependent, and is therefore described
in the ASCII Character Set Table for the appropriate interface.
Enable Code 39 Full ASCII
(1)
* Disable Code 39 Full ASCII
(0)
9-56
HS-360X Handheld DPM Scanner User Manual
Symbologies
Code 39 Security Level
Parameter # 750
The scanner offers four levels of decode security for Code 39 barcodes. There is an
inverse relationship between security and scanner aggressiveness. Increasing the level of
security can reduce scanning aggressiveness, so select only the level of security necessary.
• Code 39 Security Level 0: This setting allows the scanner to operate in its most
aggressive state, while providing sufficient security in decoding most in-spec barcodes.
• Code 39 Security Level 1: This default setting eliminates most misdecodes.
• Code 39 Security Level 2: Select this option with greater barcode security requirements
if Security Level 1 fails to eliminate misdecodes.
• Code 39 Security Level 3: If you selected Security Level 2, and misdecodes still
occur, select this security level to apply the highest safety requirements.
Selecting this option is an extreme measure against mis-decoding severely out-of-spec
barcodes. Selecting this level of security significantly impairs the decoding ability of the
scanner. If this level of security is required, try to improve the quality of the barcodes.
Code 39 Security Level 0
(0)
* Code 39 Security Level 1
(1)
Code 39 Security Level 2
(2)
HS-360X Handheld DPM Scanner User Manual
9-57
Code 39
Code 39 Security Level 3
(3)
9-58
HS-360X Handheld DPM Scanner User Manual
Symbologies
Code 39 Reduced Quiet Zone
Parameter # 1209
Scan one of the following programming symbols to enable or disable decoding Code 39
barcodes with reduced quiet zones. If you select Enable, select 1D Quiet Zone Level.
Enable Code 39 Reduced Quiet Zone
(1)
* Disable Code 39 Reduced Quiet Zone
(0)
HS-360X Handheld DPM Scanner User Manual
9-59
Code 93
Code 93
Enable/Disable Code 93
Parameter # 9
To enable or disable Code 93, scan the appropriate programming symbol below.
* Enable Code 93
(1)
Disable Code 93
(0)
9-60
HS-360X Handheld DPM Scanner User Manual
Symbologies
Set Lengths for Code 93
Parameter # L1 = 26, L2 = 27
The length of a code refers to the number of characters (i.e., human readable characters),
including check digit(s) the code contains. Set lengths for Code 93 to any length, one or
two discrete lengths, or lengths within a specific range. The default is 1 to 55.
• One Discrete Length - Select this option to decode only Code 93 symbols containing a
selected length. Select the length using the numeric programming symbols in
Appendix H — Numeric Keyboard. For example, to decode only Code 93 symbols
with 14 characters, scan Code 93 - One Discrete Length, then scan 1 followed by 4.
• Two Discrete Lengths - Select this option to decode only Code 93 symbols containing
either of two selected lengths. Select lengths using the numeric programming symbols
in Appendix H — Numeric Keyboard. For example, to decode only Code 93 symbols
containing either 2 or 14 characters, select Code 93 - Two Discrete Lengths, then scan
0, 2, 1, and then 4.
• Length Within Range - Select this option to decode a Code 93 symbol with a specific
length range. Select lengths using the numeric programming symbols in Appendix H —
Numeric Keyboard. For example, to decode Code 93 symbols containing between 4
and 12 characters, first scan Code 93 - Length Within Range. Then scan 0, 4, 1, and 2
(enter a leading zero for single digit numbers).
• Any Length - Scan this option to decode Code 93 symbols containing any number of
characters within the scanner’s capability.
Code 93 - One Discrete Length
Code 93 - Two Discrete Lengths
HS-360X Handheld DPM Scanner User Manual
9-61
Code 93
Code 93 - Length Within Range
Code 93 - Any Length
9-62
HS-360X Handheld DPM Scanner User Manual
Symbologies
Code 11
Code 11
Parameter # 10
To enable or disable Code 11, scan the appropriate programming symbol below.
Enable Code 11
(1)
* Disable Code 11
(0)
HS-360X Handheld DPM Scanner User Manual
9-63
Code 11
Set Lengths for Code 11
Parameter # L1 = 28, L2 = 29
The length of a code refers to the number of characters (i.e., human readable characters),
including check digit(s) the code contains. Set lengths for Code 11 to any length, one or
two discrete lengths, or lengths within a specific range. The default is 4 to 55.
• One Discrete Length - Select this option to decode only Code 11 symbols containing a
selected length. Select the length using the numeric programming symbols in
Appendix H — Numeric Keyboard. For example, to decode only Code 11 symbols
with 14 characters, scan Code 11 - One Discrete Length, then scan 1 followed by 4.
• Two Discrete Lengths - Select this option to decode only Code 11 symbols containing
either of two selected lengths. Select lengths using the numeric programming symbols
in Appendix H — Numeric Keyboard. For example, to decode only Code 11 symbols
containing either 2 or 14 characters, select Code 11 - Two Discrete Lengths, then scan
0, 2, 1, and then 4.
• Length Within Range - Select this option to decode a Code 11 symbol with a specific
length range. Select lengths using numeric programming symbols in Appendix H —
Numeric Keyboard. For example, to decode Code 11 symbols containing between 4
and 12 characters, first scan Code 11 - Length Within Range. Then scan 0, 4, 1, and 2
(enter a leading zero for single digit numbers).
• Any Length - Scan this option to decode Code 11 symbols containing any number of
characters within the scanner’s capability.
Code 11 - One Discrete Length
Code 11 - Two Discrete Lengths
9-64
HS-360X Handheld DPM Scanner User Manual
Symbologies
Code 11 - Length Within Range
Code 11 - Any Length
HS-360X Handheld DPM Scanner User Manual
9-65
Code 11
Code 11 Check Digit Verification
Parameter # 52
This feature allows the scanner to check the integrity of all Code 11 symbols to verify that
the data complies with the specified check digit algorithm. This selects the check digit
mechanism for the decoded Code 11 barcode. The options are to check for one check
digit, check for two check digits, or disable the feature.
To enable this feature, scan the programming symbol below corresponding to the number
of check digits encoded in the Code 11 symbols.
* Disable
(0)
One Check Digit
(1)
Two Check Digits
(2)
9-66
HS-360X Handheld DPM Scanner User Manual
Symbologies
Transmit Code 11 Check Digits
Parameter # 47
This feature selects whether or not to transmit the Code 11 check digit(s).
Note: Code 11 Check Digit Verification must be enabled for this parameter to function.
Transmit Code 11 Check Digit(s) (Enable)
(1)
* Do Not Transmit Code 11 Check Digit(s)
(Disable)
(0)
HS-360X Handheld DPM Scanner User Manual
9-67
Interleaved 2 of 5 (ITF)
Interleaved 2 of 5 (ITF)
Enable/Disable Interleaved 2 of 5
Parameter # 6
To enable or disable Interleaved 2 of 5, scan the appropriate programming symbol below,
and select an Interleaved 2 of 5 length from the following pages.
Enable Interleaved 2 of 5
(1)
* Disable Interleaved 2 of 5
(0)
9-68
HS-360X Handheld DPM Scanner User Manual
Symbologies
Set Lengths for Interleaved 2 of 5
Parameter # L1 = 22, L2 = 23
The length of a code refers to the number of characters (i.e., human readable characters),
including check digit(s) the code contains. Set lengths for I 2 of 5 to any length, one or two
discrete lengths, or lengths within a specific range. The range for Interleaved 2 of 5
lengths is 0 - 55. The default is 6 to 55.
• One Discrete Length - Select this option to decode only I 2 of 5 symbols containing a
selected length. Select the length using the numeric programming symbols in
Appendix H — Numeric Keyboard. For example, to decode only I 2 of 5 symbols with
14 characters, scan I 2 of 5 - One Discrete Length, then scan 1 followed by 4.
• Two Discrete Lengths - Select this option to decode only I 2 of 5 symbols containing
either of two selected lengths. Select lengths using the numeric programming symbols
in Appendix H — Numeric Keyboard. For example, to decode only I 2 of 5 symbols
containing either 2 or 14 characters, select I 2 of 5 - Two Discrete Lengths, then scan
0, 2, 1, and then 4.
• Length Within Range - Select this option to decode an I 2 of 5 symbol with a specific
length range. Select lengths using numeric programming symbols in Appendix H —
Numeric Keyboard. For example, to decode I 2 of 5 symbols containing between 4
and 12 characters, first scan I 2 of 5 - Length Within Range. Then scan 0, 4, 1, and 2
(enter a leading zero for single digit numbers).
• Any Length - Scan this option to decode I 2 of 5 symbols containing any number of
characters within the scanner’s capability.
Note: Due to the construction of the I 2 of 5 symbology, it is possible for a scan covering
only a portion of the code to transmit as a complete scan, yielding less data than is
encoded in the barcode. To prevent this, select specific lengths (I 2 of 5 - One Discrete
Length, Two Discrete Lengths) for I 2 of 5 applications.
I 2 of 5 - One Discrete Length
I 2 of 5 - Two Discrete Lengths
HS-360X Handheld DPM Scanner User Manual
9-69
Interleaved 2 of 5 (ITF)
I 2 of 5 - Length Within Range
I 2 of 5 - Any Length
9-70
HS-360X Handheld DPM Scanner User Manual
Symbologies
I 2 of 5 Check Digit Verification
Parameter # 49
Enable this feature to check the integrity of all I 2 of 5 symbols to verify the data complies
with either the specified Uniform Symbology Specification (USS), or the Optical Product
Code Council (OPCC) check digit algorithm.
* Disable
(0)
USS Check Digit
(1)
OPCC Check Digit
(2)
HS-360X Handheld DPM Scanner User Manual
9-71
Interleaved 2 of 5 (ITF)
Transmit I 2 of 5 Check Digit
Parameter # 44
Scan the appropriate programming symbol below to transmit I 2 of 5 data with or without the
check digit.
Transmit I 2 of 5 Check Digit (Enable)
(1)
* Do Not Transmit I 2 of 5 Check Digit
(Disable)
(0)
9-72
HS-360X Handheld DPM Scanner User Manual
Symbologies
Convert I 2 of 5 to EAN-13
Parameter # 82
Enable this parameter to convert 14-character I 2 of 5 codes to EAN-13, and transmit to
the host as EAN-13. To accomplish this, the I 2 of 5 code must be enabled, and the code
must have a leading zero and a valid EAN-13 check digit.
Convert I 2 of 5 to EAN-13 (Enable)
(1)
* Do Not Convert I 2 of 5 to EAN-13
(Disable)
(0)
HS-360X Handheld DPM Scanner User Manual
9-73
Interleaved 2 of 5 (ITF)
I 2 of 5 Security Level
Parameter # 1121
Interleaved 2 of 5 barcodes are vulnerable to misdecodes, particularly when I 2 of 5
Lengths is set to Any Length. The scanner offers four levels of decode security for Interleaved
2 of 5 barcodes. There is an inverse relationship between security and scanner aggressiveness.
Increasing the level of security can reduce scanning aggressiveness, so select only the
level of security necessary.
• I 2 of 5 Security Level 0: This setting allows the scanner to operate in its most
aggressive state, while providing sufficient security in decoding most in-spec barcodes.
• I 2 of 5 Security Level 1: A barcode must be successfully read twice, and satisfy certain
safety requirements before being decoded. This default setting eliminates most misdecodes.
• I 2 of 5 Security Level 2: Select this option with greater barcode security requirements
if Security Level 1 fails to eliminate misdecodes.
• I 2 of 5 Security Level 3: If you selected Security Level 2, and misdecodes still occur,
select this security level. The highest safety requirements are applied. A barcode must
be successfully read three times before being decoded.
Note: Selecting this option is an extreme measure against mis-decoding severely out-of-spec
barcodes. Selecting this level of security significantly impairs the decoding ability of the
scanner. If this level of security is required, try to improve the quality of the barcodes.
I 2 of 5 Security Level 0
(0)
* I 2 of 5 Security Level 1
(1)
I 2 of 5 Security Level 2
(2)
9-74
HS-360X Handheld DPM Scanner User Manual
Symbologies
I 2 of 5 Security Level 3
(3)
HS-360X Handheld DPM Scanner User Manual
9-75
Interleaved 2 of 5 (ITF)
I 2 of 5 Reduced Quiet Zone
Parameter # 1210
Scan one of the following programming symbols to enable or disable decoding I 2 of 5
barcodes with reduced quiet zones. If you select Enable, select 1D Quiet Zone Level.
Enable I 2 of 5 Reduced Quiet Zone
(1)
* Disable I 2 of 5 Reduced Quiet Zone
(0)
9-76
HS-360X Handheld DPM Scanner User Manual
Symbologies
Discrete 2 of 5 (DTF)
Enable/Disable Discrete 2 of 5
Parameter # 5
To enable or disable Discrete 2 of 5, scan the appropriate programming symbol below.
Enable Discrete 2 of 5
(1)
* Disable Discrete 2 of 5
(0)
HS-360X Handheld DPM Scanner User Manual
9-77
Discrete 2 of 5 (DTF)
Set Lengths for Discrete 2 of 5
Parameter # L1 = 20, L2 = 21
The length of a code refers to the number of characters (i.e., human readable characters),
including check digit(s) the code contains. Set lengths for D 2 of 5 to any length, one or
two discrete lengths, or lengths within a specific range. The range for Discrete 2 of 5
lengths is 1 - 55.
• One Discrete Length - Select this option to decode only D 2 of 5 symbols containing a
selected length. Select the length using the numeric programming symbols in
Appendix H — Numeric Keyboard. For example, to decode only D 2 of 5 symbols with
14 characters, scan D 2 of 5 - One Discrete Length, then scan 1 followed by 4.
• Two Discrete Lengths - Select this option to decode only D 2 of 5 symbols containing
either of two selected lengths. Select lengths using the numeric programming symbols
in Appendix H — Numeric Keyboard. For example, to decode only D 2 of 5 symbols
containing either 2 or 14 characters, select D 2 of 5 - Two Discrete Lengths, then scan
0, 2, 1, and then 4.
• Length Within Range - Select this option to decode a D 2 of 5 symbol with a specific
length range. Select lengths using numeric programming symbols in Appendix H —
Numeric Keyboard. For example, to decode D 2 of 5 symbols containing between 4
and 12 characters, first scan D 2 of 5 - Length Within Range. Then scan 0, 4, 1, and 2
(enter a leading zero for single digit numbers).
• Any Length - Scan this option to decode D 2 of 5 symbols containing any number of
characters within the scanner’s capability.
Note: Due to the construction of the D 2 of 5 symbology, it is possible for a scan covering
only a portion of the code to transmit as a complete scan, yielding less data than is
encoded in the barcode. To prevent this, select specific lengths (D 2 of 5 - One Discrete
Length, Two Discrete Lengths) for D 2 of 5 applications.
D 2 of 5 - One Discrete Length
D 2 of 5 - Two Discrete Lengths
9-78
HS-360X Handheld DPM Scanner User Manual
Symbologies
D 2 of 5 - Length Within Range
D 2 of 5 - Any Length
HS-360X Handheld DPM Scanner User Manual
9-79
Codabar (NW - 7)
Codabar (NW - 7)
Enable/Disable Codabar
Parameter # 7
To enable or disable Codabar, scan the appropriate programming symbol below.
* Enable Codabar
(1)
Disable Codabar
(0)
9-80
HS-360X Handheld DPM Scanner User Manual
Symbologies
Set Lengths for Codabar
Parameter # L1 = 24, L2 = 25
The length of a code refers to the number of characters (i.e., human readable characters),
including check digit(s) the code contains. Set lengths for Codabar to any length, one or
two discrete lengths, or lengths within a specific range. The default is 4 to 55.
• One Discrete Length - Select this option to decode only Codabar symbols containing a
selected length. Select the length using the numeric programming symbols in
Appendix H — Numeric Keyboard. For example, to decode only Codabar symbols
with 14 characters, scan Codabar - One Discrete Length, then scan 1 followed by 4.
• Two Discrete Lengths - Select this option to decode only Codabar symbols containing
either of two selected lengths. Select lengths using the numeric programming symbols
in Appendix H — Numeric Keyboard. For example, to decode only Codabar symbols
containing either 2 or 14 characters, select Codabar - Two Discrete Lengths, then
scan 0, 2, 1, and then 4.
• Length Within Range - Select this option to decode a Codabar symbol with a specific
length range. Select lengths using numeric programming symbols in Appendix H —
Numeric Keyboard. For example, to decode Codabar symbols containing between 4
and 12 characters, first scan Codabar - Length Within Range. Then scan 0, 4, 1, and 2
(enter a leading zero for single digit numbers).
• Any Length - Scan this option to decode Codabar symbols containing any number of
characters within the scanner’s capability.
Codabar - One Discrete Length
Codabar - Two Discrete Lengths
HS-360X Handheld DPM Scanner User Manual
9-81
Codabar (NW - 7)
Codabar - Length Within Range
Codabar - Any Length
9-82
HS-360X Handheld DPM Scanner User Manual
Symbologies
CLSI Editing
Parameter # 54
Enable this parameter to strip the start and stop characters and insert a space after the
first, fifth, and tenth characters of a 14-character Codabar symbol. Enable this feature if
the host system requires this data format.
Note: Symbol length does not include start and stop characters.
Enable CLSI Editing
(1)
* Disable CLSI Editing
(0)
HS-360X Handheld DPM Scanner User Manual
9-83
Codabar (NW - 7)
NOTIS Editing
Parameter # 55
Enable this parameter to strip the start and stop characters from a decoded Codabar
symbol. Enable this feature if the host system requires this data format.
Enable NOTIS Editing
(1)
*
9-84
Disable NOTIS Editing
(0)
HS-360X Handheld DPM Scanner User Manual
Symbologies
Codabar Upper or Lower Case Start/Stop Characters Detection
Parameter # 855
Select whether to detect upper case or lower case Codabar start/stop characters.
Lower Case
(1)
* Upper Case
(0)
HS-360X Handheld DPM Scanner User Manual
9-85
MSI
MSI
Enable/Disable MSI
Parameter # 11
To enable or disable MSI, scan the appropriate programming symbol below.
Enable MSI
(1)
* Disable MSI
(0)
9-86
HS-360X Handheld DPM Scanner User Manual
Symbologies
Set Lengths for MSI
Parameter # L1 = 30, L2 = 31
The length of a code refers to the number of characters (i.e., human readable characters),
including check digit(s) the code contains. Set lengths for MSI to any length, one or two
discrete lengths, or lengths within a specific range. The default is 4 to 55.
• One Discrete Length - Select this option to decode only MSI symbols containing a
selected length. Select the length using the numeric programming symbols in
Appendix H — Numeric Keyboard. For example, to decode only MSI symbols with 14
characters, scan MSI - One Discrete Length, then scan 1 followed by 4.
• Two Discrete Lengths - Select this option to decode only MSI symbols containing
either of two selected lengths. Select lengths using the numeric programming symbols
in Appendix H — Numeric Keyboard. For example, to decode only MSI symbols
containing either 2 or 14 characters, select MSI - Two Discrete Lengths, then scan 0,
2, 1, and then 4.
• Length Within Range - Select this option to decode a MSI symbol with a specific length
range. Select lengths using numeric programming symbols in Appendix H — Numeric
Keyboard. For example, to decode MSI symbols containing between 4 and 12 characters,
first scan MSI - Length Within Range. Then scan 0, 4, 1, and 2 (enter a leading zero for
single digit numbers).
• Any Length - Scan this option to decode MSI symbols containing any number of characters
within the scanner’s capability.
• Due to the construction of the MSI symbology, it is possible for a scan covering only a
portion of the code to transmit as a complete scan, yielding less data than is encoded in
the programming symbol. To prevent this, select specific lengths (MSI - One Discrete
Length, Two Discrete Lengths) for MSI applications.
MSI - One Discrete Length
MSI - Two Discrete Lengths
HS-360X Handheld DPM Scanner User Manual
9-87
MSI
MSI - Length Within Range
MSI - Any Length
9-88
HS-360X Handheld DPM Scanner User Manual
Symbologies
MSI Check Digits
Parameter # 50
With MSI symbols, one check digit is mandatory and always verified by the reader. The
second check digit is optional. If the MSI codes include two check digits, scan the Two
MSI Check Digits programming symbol to enable verification of the second check digit.
* One MSI Check Digit
(0)
Two MSI Check Digits
(1)
HS-360X Handheld DPM Scanner User Manual
9-89
MSI
Transmit MSI Check Digit(s)
Parameter # 46
Scan a programming symbol below to transmit MSI data with or without the check digit.
Transmit MSI Check Digit(s) (Enable)
(1)
* Do Not Transmit MSI Check Digit(s)
(Disable)
(0)
9-90
HS-360X Handheld DPM Scanner User Manual
Symbologies
MSI Check Digit Algorithm
Parameter # 51
Two algorithms are possible for the verification of the second MSI check digit. Select the
programming symbol below corresponding to the algorithm used to encode the check digit.
MOD 10/MOD 11
(0)
* MOD 10/MOD 10
(1)
HS-360X Handheld DPM Scanner User Manual
9-91
Chinese 2 of 5
Chinese 2 of 5
Enable/Disable Chinese 2 of 5
Parameter # 408
To enable or disable Chinese 2 of 5, scan the appropriate programming symbol below.
Enable Chinese 2 of 5
(1)
* Disable Chinese 2 of 5
(0)
9-92
HS-360X Handheld DPM Scanner User Manual
Symbologies
Matrix 2 of 5
Enable/Disable Matrix 2 of 5
Parameter # 618
To enable or disable Matrix 2 of 5, scan the appropriate programming symbol below.
Enable Matrix 2 of 5
(1)
* Disable Matrix 2 of 5
(0)
HS-360X Handheld DPM Scanner User Manual
9-93
Matrix 2 of 5
Set Lengths for Matrix 2 of 5
Parameter # L1 = 619, L2 = 620
The length of a code refers to the number of characters (i.e., human readable characters),
including check digit(s) the code contains. Set lengths for Matrix 2 of 5 to any length, one
or two discrete lengths, or lengths within a specific range. The default is 4 to 55.
• One Discrete Length - Select this option to decode only Matrix 2 of 5 symbols containing
a selected length. Select the length using the numeric programming symbols in
Appendix H — Numeric Keyboard. For example, to decode only Matrix 2 of 5 symbols
with 14 characters, scan Matrix 2 of 5 - One Discrete Length, then scan 1 followed by 4.
• Two Discrete Lengths - Select this option to decode only Matrix 2 of 5 symbols containing
either of two selected lengths. Select lengths using the numeric programming symbols
in Appendix H — Numeric Keyboard. For example, to decode only Matrix 2 of 5 symbols
containing either 2 or 14 characters, select Matrix 2 of 5 - Two Discrete Lengths, then
scan 0, 2, 1, and then 4.
• Length Within Range - Select this option to decode a Matrix 2 of 5 symbol with a specific
length range. Select lengths using the numeric programming symbols in Appendix H —
Numeric Keyboard. For example, to decode Matrix 2 of 5 symbols containing between
4 and 12 characters, first scan Matrix 2 of 5 - Length Within Range. Then scan 0, 4, 1,
and 2 (enter a leading zero for single digit numbers).
• Any Length - Scan this option to decode Matrix 2 of 5 symbols containing any number
of characters within the scanner’s capability.
Matrix 2 of 5 - One Discrete Length
Matrix 2 of 5 - Two Discrete Lengths
Matrix 2 of 5 - Length Within Range
9-94
HS-360X Handheld DPM Scanner User Manual
Symbologies
Matrix 2 of 5 - Any Length
HS-360X Handheld DPM Scanner User Manual
9-95
Matrix 2 of 5
Matrix 2 of 5 Check Digit
Parameter # 622
The check digit is the last character of the symbol used to verify the integrity of the data.
Scan the appropriate programming symbol below to transmit the barcode data with or
without the Matrix 2 of 5 check digit.
Enable Matrix 2 of 5 Check Digit
(1)
* Disable Matrix 2 of 5 Check Digit
(0)
9-96
HS-360X Handheld DPM Scanner User Manual
Symbologies
Transmit Matrix 2 of 5 Check Digit
Parameter # 623
Scan a programming symbol below to transmit Matrix 2 of 5 data with or without the check digit.
Transmit Matrix 2 of 5 Check Digit
(1)
* Do Not Transmit Matrix 2 of 5 Check
Digit
(0)
HS-360X Handheld DPM Scanner User Manual
9-97
Korean 3 of 5
Korean 3 of 5
Enable/Disable Korean 3 of 5
Parameter # 581
To enable or disable Korean 3 of 5, scan the appropriate programming symbol below.
Note: The length for Korean 3 of 5 is fixed at 6.
Enable Korean 3 of 5
(1)
* Disable Korean 3 of 5
(0)
9-98
HS-360X Handheld DPM Scanner User Manual
Symbologies
Inverse 1D
Parameter # 586
This parameter sets the 1D inverse decoder setting. Options are:
• Regular Only - the scanner decodes regular 1D barcodes only.
• Inverse Only - the scanner decodes inverse 1D barcodes only.
• Inverse Autodetect - the scanner decodes both regular and inverse 1D barcodes.
* Regular
(0)
Inverse Only
(1)
Inverse Autodetect
(2)
HS-360X Handheld DPM Scanner User Manual
9-99
GS1 DataBar
GS1 DataBar
The variants of GS1 DataBar are DataBar-14, DataBar Expanded, and DataBar Limited.
The limited and expanded versions have stacked variants. Scan the appropriate programming
symbols to enable or disable each variant of GS1 DataBar.
GS1 DataBar-14
Parameter # 338
* Enable GS1 DataBar-14
(1)
Disable GS1 DataBar-14
(0)
9-100
HS-360X Handheld DPM Scanner User Manual
Symbologies
GS1 DataBar Limited
Parameter # 339
* Enable GS1 DataBar Limited
(1)
Disable GS1 DataBar Limited
(0)
GS1 DataBar Expanded
Parameter # 340
* Enable GS1 DataBar Expanded
(1)
Disable GS1 DataBar Expanded
(0)
HS-360X Handheld DPM Scanner User Manual
9-101
GS1 DataBar
Convert GS1 DataBar to UPC/EAN
Parameter # 397
This parameter only applies to GS1 DataBar-14 and GS1 DataBar Limited symbols not
decoded as part of a Composite symbol. Enable this to strip the leading '010' from
DataBar-14 and DataBar Limited symbols encoding a single zero as the first digit, and
report the barcode as EAN-13.
For barcodes beginning with two or more zeros but not six zeros, this parameter strips the
leading '0100' and reports the barcode as UPC-A. The UPC-A Preamble parameter that
transmits the system character and country code applies to converted barcodes. Note that
neither the system character nor the check digit can be stripped.
Enable Convert GS1 DataBar to UPC/EAN
(1)
* Disable Convert GS1 DataBar to UPC/EAN
(0)
9-102
HS-360X Handheld DPM Scanner User Manual
Symbologies
GS1 DataBar Limited Security Level
Parameter # 728
The scanner offers four levels of decode security for GS1 DataBar Limited barcodes.
There is an inverse relationship between security and scanner aggressiveness. Increasing
the level of security may result in reduced aggressiveness in scanning, so choose only
that level of security necessary.
• Level 1 – No clear margin required. This complies with the original GS1 standard, yet
might result in erroneous decoding of the DataBar Limited barcode when scanning
some UPC symbols that start with digits “9” and “7”
• Level 2 – Automatic risk detection. This level of security may result in erroneous decoding
of DataBar Limited barcodes when scanning some UPC symbols. The scanner defaults
to Level 3, otherwise to Level 1.
• Level 3 – Security level reflects newly proposed GS1 standard that requires a 5 times
trailing clear margin.
• Level 4 – Security level extends beyond the standard required by GS1. This level of
security requires a
5 times leading and trailing clear margin.
GS1 DataBar Limited Security Level 1
(1)
GS1 DataBar Limited Security Level 2
(2)
* GS1 DataBar Limited Security Level 3
(3)
HS-360X Handheld DPM Scanner User Manual
9-103
GS1 DataBar
GS1 DataBar Limited Security Level 4
(4)
9-104
HS-360X Handheld DPM Scanner User Manual
Symbologies
BC412
Important: Decoder Effort must be set to Level 4 for the scanner to support BC412.
To enable or disable BC412, scan the appropriate symbol below.
Enable BC412
(1)
* Disable BC412
(0)
HS-360X Handheld DPM Scanner User Manual
9-105
Composite
Composite
Composite CC-C
Parameter # 341
Scan a programming symbol below to enable or disable Composite barcodes of type CC-C.
Enable CC-C
(1)
* Disable CC-C
(0)
9-106
HS-360X Handheld DPM Scanner User Manual
Symbologies
Composite CC-A/B
Parameter # 342
Scan a programming symbol below to enable or disable Composite barcodes of type CC-A/B.
Enable CC-A/B
(1)
* Disable CC-A/B
(0)
HS-360X Handheld DPM Scanner User Manual
9-107
Composite
Composite TLC-39
Parameter # 371
Scan a programming symbol below to enable or disable Composite barcodes of type TLC-39.
Enable TLC39
(1)
* Disable TLC39
(0)
9-108
HS-360X Handheld DPM Scanner User Manual
Symbologies
UPC Composite Mode
Parameter # 344
Select an option for linking UPC symbols with a 2D symbol during transmission as if they
were one symbol:
• Select UPC Never Linked to transmit UPC barcodes regardless of whether a 2D symbol
is detected.
• Select UPC Always Linked to transmit UPC barcodes and the 2D portion.
If 2D is not present, the UPC barcode does not transmit.
• If you select Autodiscriminate UPC Composites, the scanner determines if there is a
2D portion, then transmits the UPC, as well as the 2D portion if present.
* UPC Never Linked
(0)
UPC Always Linked
(1)
Autodiscriminate UPC Composites
(2)
HS-360X Handheld DPM Scanner User Manual
9-109
Composite
Composite Beep Mode
Parameter # 398
To select the number of decode beeps when a composite barcode is decoded, scan the
appropriate programming symbol.
Single Beep after both are decoded
(0)
* Beep as each code type is decoded
(1)
Double Beep after both are decoded
(2)
9-110
HS-360X Handheld DPM Scanner User Manual
Symbologies
GS1-128 Emulation Mode for UCC/EAN Composite Codes
Parameter # 427
Select whether to enable or disable this mode.
Enable GS1-128 Emulation Mode for
UCC/EAN Composite Codes
(1)
* Disable GS1-128 Emulation Mode for
UCC/EAN Composite Codes
(0)
HS-360X Handheld DPM Scanner User Manual
9-111
2D Symbologies
2D Symbologies
Enable/Disable PDF417
Parameter # 15
To enable or disable PDF417, scan the appropriate programming symbol below.
* Enable PDF417
(1)
Disable PDF417
(0)
9-112
HS-360X Handheld DPM Scanner User Manual
Symbologies
Enable/Disable MicroPDF417
Parameter # 227
To enable or disable MicroPDF417, scan the appropriate programming symbol below.
Enable MicroPDF417
(1)
* Disable MicroPDF417
(0)
HS-360X Handheld DPM Scanner User Manual
9-113
2D Symbologies
Code 128 Emulation
Parameter # 123
Enable this parameter to transmit data from certain MicroPDF417 symbols as Code 128.
AIM Code ID Character must be enabled for this parameter to work.
Enable Code 128 Emulation to transmit these MicroPDF417 symbols with one of the following
prefixes:
]C1
if the first codeword is 903-905
]C2
if the first codeword is 908 or 909
]C0
if the first codeword is 910 or 911
Disable Code 128 Emulation to transmit these MicroPDF417 symbols with one of the following
prefixes:
]L3
if the first codeword is 903-905
]L4
if the first codeword is 908 or 909
]L5
if the first codeword is 910 or 911
Scan a programming symbol below to enable or disable Code 128 Emulation.
Linked Micro PDF codewords 906, 907, 912, 914, and 915 are not supported. Use GS1
Composites instead.
Enable Code 128 Emulation
(1)
* Disable Code 128 Emulation
(0)
9-114
HS-360X Handheld DPM Scanner User Manual
Symbologies
Data Matrix
Parameter # 292
To enable or disable Data Matrix, scan the appropriate programming symbol below.
* Enable Data Matrix
(1)
Disable Data Matrix
(0)
GS1 Data Matrix
Parameter # 1336
To enable or disable GS1 Data Matrix, scan the appropriate programming symbol below.
* Disable GS1 Data Matrix
(0)
Enable GS1 Data Matrix
(1)
HS-360X Handheld DPM Scanner User Manual
9-115
2D Symbologies
Data Matrix Inverse
Parameter # 588
This parameter sets the Data Matrix inverse decoder setting. Options are:
• Regular Only - The scanner decodes regular Data Matrix symbols only.
• Inverse Only - The scanner decodes inverse Data Matrix symbols only.
• Inverse Autodetect - The scanner decodes both regular and inverse Data Matrix symbols.
Regular
(0)
Inverse Only
(1)
* Inverse Autodetect
(2)
9-116
HS-360X Handheld DPM Scanner User Manual
Symbologies
Maxicode
Parameter # 294
To enable or disable Maxicode, scan the appropriate programming symbol below.
Enable Maxicode
(1)
* Disable Maxicode
(0)
HS-360X Handheld DPM Scanner User Manual
9-117
2D Symbologies
QR Code
Parameter # 293
Inverse QR symbols decode if QR Code is enabled.
To enable or disable QR Code, scan the appropriate programming symbol below.
* Enable QR Code
(1)
Disable QR Code
(0)
9-118
HS-360X Handheld DPM Scanner User Manual
Symbologies
GS1 QR
Parameter # 1343
To enable or disable, scan the appropriate programming symbol below.
* Disable
(0)
Enable
(1)
HS-360X Handheld DPM Scanner User Manual
9-119
2D Symbologies
Micro QR Code
Parameter # 573
To enable or disable Micro QR Code, scan the appropriate programming symbol below.
* Enable MicroQR
(1)
Disable MicroQR
(0)
9-120
HS-360X Handheld DPM Scanner User Manual
Symbologies
Aztec
Parameter # 574
To enable or disable Aztec, scan the appropriate programming symbol below.
* Enable Aztec
(1)
Disable Aztec
(0)
HS-360X Handheld DPM Scanner User Manual
9-121
2D Symbologies
Aztec Inverse
Parameter # 589
This parameter sets the Aztec inverse decoder setting. Options are:
• Regular Only - The scanner decodes regular Aztec symbols only.
• Inverse Only - The scanner decodes inverse Aztec symbols only.
• Inverse Autodetect - The scanner decodes both regular and inverse Aztec symbols.
Regular
(0)
Inverse Only
(1)
* Inverse Autodetect
(2)
9-122
HS-360X Handheld DPM Scanner User Manual
Symbologies
Han Xin
Parameter # 1167
To enable or disable Han Xin, scan the appropriate programming symbol below.
Enable Han Xin
(1)
* Disable Han Xin
(0)
HS-360X Handheld DPM Scanner User Manual
9-123
2D Symbologies
Han Xin Inverse
Parameter # 1168
Select a Han Xin inverse decoder setting:
• Regular Only - The decoder decodes Han Xin barcodes with normal reflectance only.
• Inverse Only - The decoder decodes Han Xin barcodes with inverse reflectance only.
• Inverse Autodetect - The decoder decodes both regular and inverse Han Xin barcodes.
* Regular
(0)
Inverse Only
(1)
Inverse Autodetect
(2)
9-124
HS-360X Handheld DPM Scanner User Manual
Symbologies
DotCode
Important: Decoder Effort must be set to Level 4 for the scanner to support DotCode.
To enable or disable DotCode, scan the appropriate symbol below.
Enable DotCode
(1)
* Disable DotCode
(0)
HS-360X Handheld DPM Scanner User Manual
9-125
Postal Codes
Postal Codes
US Postnet
Parameter # 89
To enable or disable US Postnet, scan the appropriate programming symbol below.
Enable US Postnet
(1)
* Disable US Postnet
(0)
9-126
HS-360X Handheld DPM Scanner User Manual
Symbologies
US Planet
Parameter # 90
To enable or disable US Planet, scan the appropriate programming symbol below.
Enable US Planet
(1)
* Disable US Planet
(0)
HS-360X Handheld DPM Scanner User Manual
9-127
Postal Codes
Transmit US Postal Check Digit
Parameter # 95
Select whether to transmit US Postal data, which includes both US Postnet and US
Planet, with or without the check digit.
* Transmit US Postal Check Digit
(1)
Do Not Transmit US Postal Check Digit
(0)
9-128
HS-360X Handheld DPM Scanner User Manual
Symbologies
UK Postal
Parameter # 91
To enable or disable UK Postal, scan the appropriate programming symbol below.
Enable UK Postal
(1)
* Disable UK Postal
(0)
HS-360X Handheld DPM Scanner User Manual
9-129
Postal Codes
Transmit UK Postal Check Digit
Parameter # 96
Select whether to transmit UK Postal data with or without the check digit.
* Transmit UK Postal
Check Digit
(1)
Do Not Transmit UK Postal Check Digit
(0)
9-130
HS-360X Handheld DPM Scanner User Manual
Symbologies
Japan Postal
Parameter # 290
To enable or disable Japan Postal, scan the appropriate programming symbol below.
Enable Japan Postal
(1)
* Disable Japan Postal
(0)
HS-360X Handheld DPM Scanner User Manual
9-131
Postal Codes
Australia Post
Parameter # 291
To enable or disable Australia Post, scan the appropriate programming symbol below.
Enable Australia Post
(1)
* Disable Australia Post
(0)
9-132
HS-360X Handheld DPM Scanner User Manual
Symbologies
Australia Post Format
Parameter # 718
To select one of the following formats for Australia Post, scan the appropriate programming
symbol below:
• Autodiscriminate (or Smart mode) - Attempt to decode the Customer Information Field
using the N and C Encoding Tables.
Note: This option increases the risk of misdecodes because the encoded data format
does not specify the Encoding Table used for encoding.
• Raw Format - Output raw bar patterns as a series of numbers 0 through 3.
• Alphanumeric Encoding - Decode the Customer Information Field using the C Encoding
Table.
• Numeric Encoding - Decode the Customer Information Field using the N Encoding
Table.
For more information on Australia Post encoding tables, refer to the Australia Post customer
barcoding technical specifications available at:
https://auspost.com.au/business/marketing-and-communications/bulk-mailouts/
barcoding-process.
* Autodiscriminate
(0)
Raw Format
(1)
Alphanumeric Encoding
(2)
HS-360X Handheld DPM Scanner User Manual
9-133
Postal Codes
Numeric Encoding
(3)
9-134
HS-360X Handheld DPM Scanner User Manual
Symbologies
Netherlands KIX Code
Parameter # 326
To enable or disable Netherlands KIX Code, scan the appropriate programming symbol below.
Enable Netherlands KIX Code
(1)
* Disable Netherlands KIX Code
(0)
HS-360X Handheld DPM Scanner User Manual
9-135
Postal Codes
USPS 4CB/One Code/Intelligent Mail
Parameter # 592
To enable or disable USPS 4CB/One Code/Intelligent Mail, scan the appropriate programming
symbol below.
Enable USPS 4CB/One Code/Intelligent Mail
(1)
* Disable USPS 4CB/One Code/Intelligent Mail
(0)
9-136
HS-360X Handheld DPM Scanner User Manual
Symbologies
UPU FICS Postal
Parameter # 611
To enable or disable UPU FICS Postal, scan the appropriate programming symbol below.
Enable UPU FICS Postal
(1)
* Disable UPU FICS Postal
(0)
HS-360X Handheld DPM Scanner User Manual
9-137
Postal Codes
Mailmark
Parameter # 1337
To enable or disable Mailmark, scan the appropriate programming symbol below.
* Disable Mailmark
(0)
Enable Mailmark
(1)
9-138
HS-360X Handheld DPM Scanner User Manual
Symbologies
Symbology-Specific Security Levels
Redundancy Level
Parameter # 78
The scanner offers four levels of decode redundancy. Select higher redundancy levels for
decreasing levels of barcode quality. As redundancy levels increase, the scanner’s
aggressiveness decreases.
Select the redundancy level appropriate for the barcode quality.
Redundancy Level 1
The following code types must be successfully read twice before being decoded:
Code Type
Code Length
Codabar
8 characters or less
MSI
4 characters or less
D 2 of 5
8 characters or less
I 2 of 5
8 characters or less
Redundancy Level 2
The following code types must be successfully read twice before being decoded:
Code Type
Code Length
All
All
Redundancy Level 3
Code types other than the following must be successfully read twice before being
decoded. The following codes must be read three times:
Code Type
Code Length
MSI
4 characters or less
D 2 of 5
8 characters or less
I 2 of 5
8 characters or less
Codabar
8 characters or less
HS-360X Handheld DPM Scanner User Manual
9-139
Symbology-Specific Security Levels
Redundancy Level 4
The following code types must be successfully read three times before being decoded:
Code Type
Code Length
All
All
* Redundancy Level 1
(1)
Redundancy Level 2
(2)
Redundancy Level 3
(3)
Redundancy Level 4
(4)
9-140
HS-360X Handheld DPM Scanner User Manual
Symbologies
Security Level
Parameter # 77
The scanner offers four levels of decode security for delta barcodes, which include the
Code 128 family, UPC/EAN, and Code 93. Select increasing levels of security for decreasing
levels of barcode quality. There is an inverse relationship between security and scanner
aggressiveness, so choose only that level of security necessary for any given application.
• Security Level 0: This setting allows the scanner to operate in its most aggressive
state, while providing sufficient security in decoding most “in-spec” barcodes.
• Security Level 1: This default setting eliminates most misdecodes.
• Security Level 2: Select this option if Security level 1 fails to eliminate misdecodes.
• Security Level 3: If you selected Security Level 2 and misdecodes still occur, select this
security level. Be advised, selecting this option is an extreme measure against mis-decoding
severely out-of-spec barcodes. Selecting this level of security significantly impairs the
decoding ability of the scanner. If you need this level of security, try to improve the quality
of the barcodes.
Security Level 0
(0)
* Security Level 1
(1)
Security Level 2
(2)
HS-360X Handheld DPM Scanner User Manual
9-141
Symbology-Specific Security Levels
Security Level 3
(3)
9-142
HS-360X Handheld DPM Scanner User Manual
Symbologies
1D Quiet Zone Level
Parameter # 1288
This feature sets the level of aggressiveness in decoding barcodes with a reduced quiet
zone (the area in front of and at the end of a barcode), and applies to symbologies enabled
by a Reduced Quiet Zone parameter. Because higher levels increase the decoding time and
risk of misdecodes, Symbol Technologies strongly recommends enabling only the symbologies
which require higher quiet zone levels, and leaving Reduced Quiet Zone disabled for all
other symbologies. Options are:
• 0 - The scanner performs normally in terms of quiet zone.
• 1 - The scanner performs more aggressively in terms of quiet zone.
• 2 - The scanner only requires one side EB (end of barcode) for decoding.
• 3 - The scanner decodes anything in terms of quiet zone or end of barcode.
1D Quiet Zone Level 0
(0)
* 1D Quiet Zone Level 1
(1)
1D Quiet Zone Level 2
(2)
1D Quiet Zone Level 3
(3)
HS-360X Handheld DPM Scanner User Manual
9-143
Symbology-Specific Security Levels
Intercharacter Gap Size
Parameter # 381
The Code 39 and Codabar symbologies have an intercharacter gap that is typically quite
small. Due to various barcode-printing technologies, this gap can grow larger than the
maximum size allowed, preventing the scanner from decoding the symbol. If this problem
occurs, scan the Large Intercharacter Gaps parameter to tolerate these out-of-spec barcodes.
* Normal Intercharacter Gaps
(6)
Large Intercharacter Gaps
(10)
9-144
HS-360X Handheld DPM Scanner User Manual
Symbologies
Report Version
Scan the programming symbol below to report the version of software installed in the scanner.
Report Software Version
HS-360X Handheld DPM Scanner User Manual
9-145
MacroPDF Features
MacroPDF Features
MacroPDF is a special feature for concatenating multiple PDF symbols into one file. The
scanner can decode symbols that are encoded with this feature, and can store more than
64 Kb of decoded data stored in up to 50 MacroPDF symbols.
Caution: When printing, keep each MacroPDF sequence separate, as each sequence
has unique identifiers. Do not mix barcodes from several MacroPDF sequences, even if
they encode the same data. When scanning MacroPDF sequences, scan the entire
MacroPDF sequence without interruption. If, when scanning a mixed sequence, the
scanner emits two long low beeps (Low/Low) this indicates an inconsistent file ID or
inconsistent symbology error.
Flush Macro Buffer
This flushes the buffer of all decoded MacroPDF data stored to that point, transmits it to
the host device, and aborts from MacroPDF mode.
Flush MacroPDF Buffer
Abort MacroPDF Entry
This clears all currently-stored MacroPDF data in the buffer without transmission and
aborts from MacroPDF mode.
Abort MacroPDF Entry
9-146
HS-360X Handheld DPM Scanner User Manual
10 WebLinkPC
This section describes how to set up and use WebLinkPC, Omron Microscan’s configuration
software for the HS-360X Handheld DPM Scanner.
WebLinkPC is browswer-based, enabling quick and easy configuration and testing of HS-360X
Handheld Scanners. WebLinkPC is reliable, lightweight, and operating-system-independent
without compromising the power and depth of its tool set.
WebLinkPC offers novice users an intuitive way to connect, configure, monitor, and troubleshoot
an HS-360X, and provides the power and flexibility expected by advanced users.
Important: Full WebLinkPC documentation is located in WebLinkPC Help, which can be
accessed by clicking the Question Mark icon at the upper right of the WebLinkPC user interface.
Important: Scanning programming symbols while using WebLinkPC may cause unexpected
behavior when the scanner is in Setup or Run mode. For example, scanning the USB CDC
programming symbol while in Setup mode may cause additional data to be output with the
string data once the communication mode is switched. Use WebLinkPC controls to perform
this function, or scan additional programming symbols after exiting WebLinkPC.
HS-360X Handheld DPM Scanner User Manual
10-1
Overview
Overview
Splash Screen
After you double-click the WebLinkPC icon on your desktop or open a web browser and
enter http://localhost:8090 or http://127.0.0.1:8090, the first thing you will see is the
splash screen shown below.
Navigation Bar
The navigation bar at the top of the WebLinkPC interface features buttons for three primary
views: Start, Setup, and Run.
10-2
HS-360X Handheld DPM Scanner User Manual
WebLinkPC
Barcode Programming
Click the Barcode Programming icon to open the Barcode Programming view.
When the Differences from Default radio button is selected, Barcode Programming
automatically creates a Differences from Default Data Matrix symbol encoded with all the
scanner's current settings that are different from default settings. Any time the Differences
from Default symbol is subsequently decoded, it returns the scanner to those same settings.
When you select Add Default Settings Barcode, a Restore Defaults Data Matrix symbol
appears. Scanning the Restore Defaults symbol returns the scanner to factory default settings.
When the Favorites radio button is selected, Barcode Programming automatically creates
a Favorites symbol encoded with all the settings that are marked as favorites in the
Advanced Settings menus. Any time the Favorites symbol is subsequently decoded, it
returns the scanner to the user-defined settings for only those parameters.
When you select Add Default Settings Barcode, a Restore Defaults Data Matrix symbol
appears. Scanning the Restore Defaults symbol returns the scanner to factory default settings.
By clicking the Printer icon, you can print your Differences from Default or Favorites configuration
symbol with a title and footer of your choice.
HS-360X Handheld DPM Scanner User Manual
10-3
Connect to WebLinkPC
Help Icon
The help icon is located to the right of the Barcode Programming icon. Click this icon to
open WebLinkPC Help.
Application Settings Icon
Click the Gear icon to the right of the help icon to open the Application Settings menu.
10-4
HS-360X Handheld DPM Scanner User Manual
WebLinkPC
Left Panel
The area to the left of the Image Area is different depending on whether you are in the
Start or Setup view. (In the Run view, the Image Area expands and the left panel is not
present.)
Left Panel in Start View
In the Start view, the left panel shows the Reader Model, Serial Number, and Firmware
version.
Note: The information in this area is selectable so that you can copy it to a clipboard.
The left panel in the Start view also contains buttons for Assisted Setup, Create a New
Setup, and Load a Setup.
Left Panel in Setup View
In the Setup view, the left panel contains the majority of WebLinkPC's configuration tools:
Cycle, which allows you to set the trigger mode; Performance, which allows you to set
the amount of time the scanner will attempt to decode a symbol; Decode, which allows
you to choose which symbologies the scanner can decode; Format Output, which allows
you to determine the ways in which barcode data can be formatted before it is output as a
data string; and Favorites, which allows you to define the commands you use most frequently
and gives you quick access to their command parameters.
HS-360X Handheld DPM Scanner User Manual
10-5
Overview
Right Panel
The panel to the right of the Image Area shows Cycle Count and Cycle Time, and an
Output Data area that displays decoded symbol data.
If you set a Preamble in Format Output, it is displayed before decoded symbol data in the
Output Data area. If you select a Postamble, it is displayed after decoded symbol data.
In the example below, Postamble 1 is set to CTRL I/HORIZ TAB in Format Output and
displayed after decoded symbol data in the Output Data area.
10-6
HS-360X Handheld DPM Scanner User Manual
WebLinkPC
Image Area
The Image Area is the main focus of WebLinkPC. This area allows you to see what currently
falls within the HS-360X's field of view, and offers four image control tools.
Image Control Toolbar
Fit Image to Window
Fits the captured image to the Image Area window.
Zoom In
Zooms in on the desired area of the captured image.
Zoom Out
Zooms out and decreases the size of the captured image.
Note: You can also zoom in and out by scrolling up or down with your mouse, and you can
move the image around by clicking and dragging.
Save Current Image
Allows you to save the current captured image to the location of your choice on your PC.
HS-360X Handheld DPM Scanner User Manual
10-7
Overview
Status Bar
The Status Bar shows the serial number of the current reader at the lower left of the
WebLinkPC interface.
Click the Light Bulb icon to activate the current reader's indicator LEDs.
Click the Speaker icon to activate the current reader's beeper.
When you update firmware from the Utilities view, a Firmware Update progress bar
appears in the Status Bar.
10-8
HS-360X Handheld DPM Scanner User Manual
WebLinkPC
Quick Start
Check Hardware and Connect the System
Wired HS-360X
HS-360X Handheld DPM Scanner User Manual
10-9
Quick Start
Attach Wired HS-360X Cable
1. Insert cable fully so connector is flush with scanner surface.
2. Loosen metal lock plate screws using a PH1 driver.
3. Slide lock plate to fully locked position.
4. Tighten screw using a PH1 driver (torque: 5 in-lb).
Hardware Configuration for Wired HS-360X
10-10
HS-360X Handheld DPM Scanner User Manual
WebLinkPC
Wireless HS-360X
HS-360X Handheld DPM Scanner User Manual
10-11
Quick Start
Cradle Cable Connection
10-12
HS-360X Handheld DPM Scanner User Manual
WebLinkPC
Cradle Insertion
Battery Insertion and Removal
HS-360X Handheld DPM Scanner User Manual
10-13
Quick Start
Hardware Configuration for Wireless HS-360X
Note: Cables may vary depending on configuration.
When connecting the
HS-360X and cradle to
a PC, look for a USB
port with a lightning
bolt icon similar to the
one shown here. This
icon indicates that the
port is higher-powered
and is intended for
charging USB devices.
HS-360X Wireless Scanner USB Host Interface
Set Up Host Interface (Wired or Wireless HS-360X)
Scan one of the symbols below.
The interface cable automatically detects the host interface type and uses the default setting.
If the default (*) does not meet your requirements, scan the appropriate host symbol below.
* USB HID Keyboard
Emulation
Return to Factory
Defaults
USB – Override
Caps Lock Key
(Enable)
10-14
SNAPI with Imaging
Interface
USB CDC Host
(Virtual COM)
Add an Enter Key
(Carriage Return /
Line Feed)
Add a Tab Key
USB – Do Not
Override Caps
Lock Key (Disable)
HS-360X Handheld DPM Scanner User Manual
WebLinkPC
Install WebLinkPC and Connect
Install
The WebLinkPC installer can be found in the following two locations:
• In the Download Center at: www.microscan.com/downloadcenter
• On the Omron Microscan Tools Drive: P/N 37-000010-01.
1. Download WebLinkPC and follow the installation prompts.
2. Click on the WebLinkPC icon to run the program.
Minimum PC Requirements
•
•
•
•
•
•
•
Intel® Core™ 2 Duo Processor
Microsoft Windows 7 (32-bit)
Firefox, current version; Edge, current version
1 GB / 128 MB Video RAM
100 MB hard drive space
16-bit color display
3.0 Windows Experience Index
Recommended PC Requirements
•
•
•
•
•
•
•
Intel® Core™ i3 Duo Processor
Microsoft Windows 7 (64-bit) or Microsoft Windows 10 (64-bit)
Google Chrome, current version
2 GB RAM / 128 MB Video RAM
500 MB hard drive space
32-bit color display
4.0 Windows Experience Index
HS-360X Handheld DPM Scanner User Manual
10-15
Quick Start
Connect
To start WebLinkPC, double-click the icon that was placed on your desktop during installation.
You can also start WebLinkPC by connecting the HS-360X to your PC, opening a browser
of your choice, and typing http://localhost:8090 or http://127.0.0.1:8090 in the address bar.
10-16
HS-360X Handheld DPM Scanner User Manual
WebLinkPC
Explore the Start View
The Start view shows all the scanners available to the system. The Reader Model, Serial
Number, and Firmware Version of each scanner are displayed. This view allows you to
choose Assisted Setup, to Create a New Setup, or to Load a Setup. The Gear icon in
the upper right brings up the Application Settings Menu.
HS-360X Handheld DPM Scanner User Manual
10-17
Quick Start
Create a New Setup or Load an Existing Setup
Assisted Setup
When you click the Assisted Setup button in the Start view, a dialog will appear asking
you a series of application-related questions. Based on your answers, WebLinkPC generates
your initial setup automatically. Once the setup is created, you can fine-tune its parameters
in the Setup view.
10-18
HS-360X Handheld DPM Scanner User Manual
WebLinkPC
Create a New Setup
The Start view also allows you to create a New Setup without using Assisted Setup.
When you click the Create a New Setup button, WebLinkPC searches for any differences
from default in the scanner parameters. If no differences from default are found, you will
see the Setup view. If differences from default are found, the following message will appear:
Load a Setup
Select Load a Setup to load an existing .rls WebLinkPC setup file.
HS-360X Handheld DPM Scanner User Manual
10-19
Quick Start
Explore the Setup View
The Setup view allows you to configure the scanner, view the current captured image, and
view decoded symbol data.
The following read cycle steps are shown at the left side of the screen:
• Cycle
• Performance
• Decode
• Format Output
10-20
HS-360X Handheld DPM Scanner User Manual
WebLinkPC
Configure Cycle Settings
The Cycle step allows you to choose between Manual and Presentation Trigger Modes.
In Manual mode, a decode is attempted when you pull the trigger.
Manual mode in the Cycle step allows you to set Decode Timeout and enable or disable
a No Read Message.
In Presentation mode, the read cycle begins when a symbol is detected moving into the
scanner’s field of view.
Presentation mode in the Cycle step allows you to enable or disable a Presentation
Target, set the Hands-Free Decode Timeout, set the Timeout Between Decodes, and
enable or disable a No Read Message.
Note: The scanner is automatically set to Presentation mode when placed in the HS-360X
Stand, shown below.
HS-360X Handheld DPM Scanner User Manual
10-21
Quick Start
Configure Performance Settings
Performance Step (DPM Optimization)
The Performance step allows you to optimize the scanner for Direct Part Mark (DPM)
decoding. A DPM is a permanent mark created by laser etch, chemical etch, or other
method, directly on a substrate. DPMs are often harder to read than other symbols, and
may require a few attempts before finding optimal settings. The Decoder Effort slider has
four settings: Level 1, corresponding to Min on the slider; Level 2; Level 3; and Level 4,
corresponding to Max on the slider. As Decoder Effort is moved toward Max, the decoder
spends an increasing amount of time trying to decode the symbol.
In Level 4, you can also enable the Enhance option, which improves readability by adding
an image pre-processing operation (Shrink Dark or Grow Dark) to improve decode performance
on marks whose cells are not properly formed. You can also select the size (Small,
Medium, or Large) of the area or "pixel neighborhood" in which the pre-processing operation
is performed. Small = 3 x 3 pixels, Medium = 5 x 5 pixels, and Large = 7 x 7 pixels.
The Illumination Control options are:
• Direct: White LED illumination only. Recommended for use with dot-peened symbols.
Tilt the part 30° to avoid specular reflection when using Direct illumination.
• Indirect: Red LED illumination only. Recommended for use with laser-etched symbols
on curved, rough, grainy, highly-reflective, or visibly-machined surfaces or cylinders.
• Cycle: Alternates between Direct and Indirect illumination, starting with the type of
illumination used during the last successful decode.
Examples of Performance Configurations
•
•
•
•
Level 4 (Maximum) Decoder Effort;
Enhance – Shrink Dark pre-processing operation enabled;
Medium-sized pre-processing area;
Illumination Control set to Cycle.
10-22
HS-360X Handheld DPM Scanner User Manual
WebLinkPC
• Level 3 Decoder Effort;
• Illumination Control set to Cycle.
•
•
•
•
Level 4 (Maximum) Decoder Effort;
Enhance – Shrink Dark pre-processing operation enabled;
Small pre-processing area;
Illumination Control set to Cycle.
HS-360X Handheld DPM Scanner User Manual
10-23
Quick Start
Clicking the Question Mark icon in the upper right corner of the Performance step editor
brings up a dialog with more detail about each level of decoder effort.
10-24
HS-360X Handheld DPM Scanner User Manual
WebLinkPC
Configure Symbology and Decode Settings
Decode Step
The Decode step allows you to select which symbologies to enable and disable. Clicking
the 1D Codes and 2D Codes checkboxes will enable or disable all the symbologies in that
group.
You can also click directly on the images of the 1D and 2D symbols and a popup menu
with checkboxes will appear, allowing you to select individual symbologies to enable or
disable. In the example below, the user has clicked on the image of the Data Matrix symbol,
causing the 2D Codes menu to appear.
HS-360X Handheld DPM Scanner User Manual
10-25
Quick Start
Clicking the Gear icon to the right of the 1D Codes and 2D Codes checkboxes brings up a
Symbology Settings dialog that allows you to modify specific parameters for each symbology.
10-26
HS-360X Handheld DPM Scanner User Manual
WebLinkPC
Configure Output Formatting
Format Output Step
The Format Output step allows you to configure Preambles and Postambles (Prefixes
and Suffixes) to add to symbol data output.
The Simplified version of this control allows you to Append Return or Append Tab after
each string of data output.
The Advanced version allows you to choose from a wide variety of keyboard characters
that can be output as a Preamble or Postamble. You can also add a second Postamble if
required. You can toggle between the two views by clicking directly on the words
Advanced and Simplified in the lower right corner of the dialog.
HS-360X Handheld DPM Scanner User Manual
10-27
Quick Start
If Preamble or Postamble are enabled, the user-selected keyboard character value will
appear in Output Data. In the example below, the CTRL I/HORIZ TAB value is set as
Postamble 1, which is why it appears after the symbol data (ID20304092015).
10-28
HS-360X Handheld DPM Scanner User Manual
WebLinkPC
Run the Application
The Run view allows you to keep track of your application during runtime. The current
captured image is shown along with a row of image control tools. A history of decoded
symbol data is shown in the right pane along with any preambles or postambles that have
been defined.
The Output Data display in the right pane shows a list of previous read cycle results. Each
result is selectable and erasable.
Image Control Tools
Image control tools are available at the upper right of the image view.
HS-360X Handheld DPM Scanner User Manual
10-29
Start
Start
The Start view is the initial view you will see after the splash screen when the WebLinkPC
session begins. Each connected scanner on the network is shown, along with its user-defined
name, Reader Model, Serial Number, and Firmware version.
This view also allows you to choose Assisted Setup, to Create a New Setup, or to Load
a Setup.
Note: If the scanner is in SNAPI mode and you click Keyboard Emulators in the Start
view, you will see this message at the lower right of the window:
If you don't see your reader in the Start view, click Where's My Reader? to bring up the
Locate Reader dialog.
10-30
HS-360X Handheld DPM Scanner User Manual
WebLinkPC
Communication Mode Warning Dialog
If the scanner is in SNAPI mode when the server locates it, a dialog will appear allowing
you to choose which mode you want the reader to be in when you close WebLinkPC:
Keyboard or USB CDC (Virtual Comm). This allows the scanner to be usable outside the
WebLinkPC user interface. (When the scanner is in SNAPI mode, the only way to communicate
with it is via the WebLinkPC user interface.)
If you click Don’t ask again, a Reset Comm Warning button will appear in the Utilities
view that allows the user to reset this dialog option. When you click Reset Comm Warning,
a message appears stating that the warning has been re-enabled.
HS-360X Handheld DPM Scanner User Manual
10-31
Start
Application Settings
Click the Gear icon at the upper right to bring up the Application Settings menu. This
menu includes several functions: Save, New, Load, Advanced, Utilities, Beeper,
Guided Tour, Restore Default Settings, and About WebLinkPC.
Clicking About WebLinkPC opens the dialog shown below, which displays the current
WebLinkPC version, Browser, Operating System, and Screen Resolution.
Note: The information in this dialog is selectable so that you can copy it to a clipboard.
Clicking Contact Us takes you to the Omron Microscan website.
10-32
HS-360X Handheld DPM Scanner User Manual
WebLinkPC
Assisted Setup
When you click the Assisted Setup button in the Start view, a dialog will appear asking
you a series of application-based questions. Based on your answers, WebLinkPC generates
your initial setup automatically. Once the setup is created, you can fine-tune its parameters
in the Setup view.
The Assisted Setup dialog is designed to be logical and intuitive, and follows this
sequence:
• You are asked which code types you will be reading in your application. Code types can
be added by clicking directly in the code type field and selecting them from a dropdown menu.
• Then you are asked if you would like to append a tab or return to decoded symbol data.
If you do, one or both will be added to symbol data output.
• You are then given a selection of two application types, which represent the available
selections in the Cycle area of the left panel in the Setup view. The icons represent the
Manual and Presentation Trigger Modes.
• The next prompt allows you to set the volume of the good read (decode) beeper.
• Finally, you are given the option of enabling or disabling Vibrate on Decode, which
causes the scanner to vibrate when a good read occurs.
Click Create Setup to configure your WebLinkPC setup automatically based on your
answers to the Assisted Setup questions.
HS-360X Handheld DPM Scanner User Manual
10-33
Start
Reader Information
The Reader Information section of the left panel of the Start view shows your reader's
user-defined name, Reader Model, Serial Number, and Firmware version.
Icons show the type of scanner (wired or wireless) and current battery life.
Clicking the light bulb icon activates the selected scanner's LEDs, and clicking the speaker
icon causes the selected speaker to beep.
Note: The information in this area is selectable so that you can copy it to a clipboard.
Setup Buttons
Assisted Setup
When you click the Assisted Setup button in the Start view, a dialog with a series of
questions about your application will appear. Answering these simple questions allows
WebLinkPC to configure your setup for you.
Create a New Setup
New Setup allows you to create a new setup without using Assisted Setup. When you
click the New Setup button, WebLinkPC searches for any differences from default in the
scanner parameters. If no differences from default are found, you will see the Setup view.
If differences from default are found, the following alert will appear, allowing you to choose
whether to restore the scanner to default settings or to cancel the New Setup.
Load a Setup
Select Load Setup to load an existing .rls WebLinkPC setup file.
10-34
HS-360X Handheld DPM Scanner User Manual
WebLinkPC
Setup
The Setup view allows you to configure all aspects of a setup. Multiple discrete sections of
the interface give you the ability to set Cycle, Performance, Decode, Format Output,
and Favorites.
The Question Mark icon at the upper right opens WebLinkPC Help.
The Gear icon at the upper right brings up the Application Settings menu. This menu
includes several functions: Save, New, Load, Advanced, Utilities, Beeper, Guided Tour,
Restore Default Settings, and About WebLinkPC.
HS-360X Handheld DPM Scanner User Manual
10-35
Setup
About WebLinkPC opens the dialog below, which shows the current WebLinkPC version,
Browser, Operating System, and Screen Resolution.
Note: The information in this dialog is selectable so that you can copy it to a clipboard.
Clicking Contact Us takes you to the Omron Microscan website.
10-36
HS-360X Handheld DPM Scanner User Manual
WebLinkPC
Cycle
The Cycle step allows you to choose between Manual and Presentation Trigger Modes.
In Manual mode, a decode is attempted when you pull the trigger.
Manual mode in the Cycle step allows you to set Decode Timeout and enable or disable
a No Read Message.
In Presentation mode, the read cycle begins when a symbol is detected moving into the
scanner’s field of view.
Presentation mode in the Cycle step allows you to enable or disable a Presentation
Target, set the Hands-Free Decode Timeout, set the Timeout Between Decodes, and
enable or disable a No Read Message.
Note: The scanner is automatically set to Presentation mode when placed in the HS-360X
Stand, shown below.
HS-360X Handheld DPM Scanner User Manual
10-37
Setup
Performance (DPM Optimization)
The Performance step allows you to optimize the scanner for Direct Part Mark (DPM)
decoding. A DPM is a permanent mark created by laser etch, chemical etch, or other
method, directly on a substrate. DPMs are often harder to read than other symbols, and
may require a few attempts before finding optimal settings. The Decoder Effort slider has
four settings: Level 1, corresponding to Min on the slider; Level 2; Level 3; and Level 4,
corresponding to Max on the slider. As Decoder Effort is moved toward Max, the decoder
spends an increasing amount of time trying to decode the symbol.
In Level 4, you can also enable the Enhance option, which improves readability by adding
an image pre-processing operation (Shrink Dark or Grow Dark) to improve decode performance
on marks whose cells are not properly formed. You can also select the size (Small,
Medium, or Large) of the area or "pixel neighborhood" in which the pre-processing operation
is performed. Small = 3 x 3 pixels, Medium = 5 x 5 pixels, and Large = 7 x 7 pixels.
The Illumination Control options are:
• Direct: White LED illumination only. Recommended for use with dot-peened symbols.
Tilt the part 30° to avoid specular reflection when using Direct illumination.
• Indirect: Red LED illumination only. Recommended for use with laser-etched symbols
on curved, rough, grainy, highly-reflective, or visibly-machined surfaces or cylinders.
• Cycle: Alternates between Direct and Indirect illumination, starting with the type of
illumination used during the last successful decode.
Examples of Performance Configurations
•
•
•
•
Level 4 (Maximum) Decoder Effort;
Enhance – Shrink Dark pre-processing operation enabled;
Medium-sized pre-processing area;
Illumination Control set to Cycle.
10-38
HS-360X Handheld DPM Scanner User Manual
WebLinkPC
• Level 3 Decoder Effort;
• Illumination Control set to Cycle.
•
•
•
•
Level 4 (Maximum) Decoder Effort;
Enhance – Shrink Dark pre-processing operation enabled;
Small pre-processing area;
Illumination Control set to Cycle.
HS-360X Handheld DPM Scanner User Manual
10-39
Setup
Clicking the Question Mark icon in the upper right corner of the Performance step editor
brings up a dialog with more detail about each level of decoder effort.
10-40
HS-360X Handheld DPM Scanner User Manual
WebLinkPC
Decode
The Decode step allows you to select which symbologies to enable and disable. Clicking
the 1D Codes and 2D Codes checkboxes will enable or disable all the symbologies in that
group.
You can also click directly on the images of the 1D and 2D symbols and a popup menu
with checkboxes will appear, allowing you to select individual symbologies to enable or
disable. In the example below, the user has clicked on the image of the Data Matrix symbol,
causing the 2D Codes menu to appear.
HS-360X Handheld DPM Scanner User Manual
10-41
Setup
Clicking the Gear icon to the right of the 1D Codes and 2D Codes checkboxes brings up a
Symbology Settings dialog that allows you to modify specific parameters for each symbology.
10-42
HS-360X Handheld DPM Scanner User Manual
WebLinkPC
Format Output
The Format Output step allows you to configure Preambles and Postambles (Prefixes
and Suffixes) to add to symbol data output.
The Simplified version of this control allows you to Append Return or Append Tab after
each string of data output.
The Advanced version allows you to choose from a wide variety of keyboard characters
that can be output as a Preamble or Postamble. You can also add a second Postamble if
required. You can toggle between the two views by clicking directly on the words
Advanced and Simplified in the lower right corner of the dialog.
HS-360X Handheld DPM Scanner User Manual
10-43
Setup
If Preamble or Postamble are enabled, the user-selected keyboard character value will
appear in Output Data. In the example below, the CTRL I/HORIZ TAB value is set as
Postamble 1, which is why it appears after the symbol data (ID20304092015).
10-44
HS-360X Handheld DPM Scanner User Manual
WebLinkPC
Favorites
The Favorites area of the Setup view displays commands that you have selected as
favorites by clicking the star icons next to command names in the Advanced Settings
menus. Double-clicking the blue parameter text brings up dropdown menus that allow you
to change the parameters of frequently-used commands without returning to the
Advanced Settings menus.
In the example below, notice that the star icon next to the Image File Format command in
the Imaging menu is selected. This causes that command to appear in the Favorites editor
in the left panel of WebLinkPC's Setup view. Commands that are displayed in Favorites
can be configured via dropdown menu in the same way as commands in Advanced Settings.
HS-360X Handheld DPM Scanner User Manual
10-45
Run
Run
In the Run view, you can observe your scanner's configuration in action as it follows the
parameters you have defined. The right panel shows Counts and Output Data. Preambles
and Postambles are shown along with decoded symbol data. You can reset Output Data
by clicking the eraser icon.
Counts
The Counts area of the right panel provides two data points:
• Cycle Count is the number of read cycles that have occurred. If no read is enabled
(which it is by default when entering the Setup view) then any no reads will be included
in the count.
• Cycle Time is the amount of time, in milliseconds, that the scanner spent decoding the
most recent symbol. The Cycle Time is 0 for a no read.
Output Data
The Output Data area of the right panel shows the data from each decoded symbol. The
Preamble and Postamble are also shown here if enabled and configured.
10-46
HS-360X Handheld DPM Scanner User Manual
WebLinkPC
Application Settings
Click the Gear icon to the right of the help icon to open the Application Settings menu.
Application Settings Menu
The Application Settings menu includes several functions: Save, New, Load, Advanced,
Utilities, Beeper, Guided Tour, Restore Default Settings, and About WebLinkPC.
HS-360X Handheld DPM Scanner User Manual
10-47
Application Settings
Save
Save saves the current configuration.
New
New opens a completely new WebLinkPC session.
10-48
HS-360X Handheld DPM Scanner User Manual
WebLinkPC
Load
Load allows you to open an existing configuration.
Advanced
Advanced allows you to make precise adjustments to every category of reader functionality
using the Advanced Settings menus.
HS-360X Handheld DPM Scanner User Manual
10-49
Application Settings
Utilities
Clicking Utilities opens a view that allows you to switch between Keyboard Mode and
USB CDC (Virtual COM Port) Mode for the selected scanner, and also to update HS-360X
firmware.
10-50
HS-360X Handheld DPM Scanner User Manual
WebLinkPC
Updating Firmware
To update firmware, select the scanner or scanners you wish to update by clicking their
check boxes, then click the Choose File button and select the appropriate firmware file. If
an individual .dat file is selected, only the scanners whose models are associated with that
.dat file will be updated. Any scanners not associated with that .dat file will not be updated.
Scanner-to-File Associations:
• HS-360X Wired Scanner: PAADJC06.dat
• HS-360X Wireless Scanner: PAADKC06.dat
• HS-360X Cradle (Base Station): CAACNS00.dat
A .zip file can also be provided that contains multiple .dat files. The file server chooses the
appropriate binary file in the .zip file for each scanner model.
Note: The HS-360X Cradle's firmware cannot be updated via .zip file. It must be updated
on its own, but the process is the same. Select the HS-360X Wireless Scanner paired with
the Cradle whose firmware you want to update, then select and install the Cradle's firmware.
When the firmware download begins, a Downloading Firmware dialog will appear:
HS-360X Handheld DPM Scanner User Manual
10-51
Application Settings
If you click Hide, the dialog minimizes to the Status Bar. The firmware update begins once
firmware is downloaded. Progress is shown by a simple Firmware Update progress bar.
You can continue to work with other connected scanners during the firmware update.
10-52
HS-360X Handheld DPM Scanner User Manual
WebLinkPC
Beeper
Enabling Beeper causes your PC to beep when WebLinkPC receives a valid decode from
the reader.
Guided Tour
Clicking Guided Tour launches a tutorial that explains the functions of the various areas
of the WebLinkPC user interface.
HS-360X Handheld DPM Scanner User Manual
10-53
Application Settings
The Guided Tour is a multi-step tutorial that explains the functions of the various areas of
the WebLinkPC user interface.
Step 9 of the tour is shown here as an example.
10-54
HS-360X Handheld DPM Scanner User Manual
WebLinkPC
Restore Default Settings
Clicking the Restore Default Settings button brings up the message shown below. If you
click Restore to Factory Defaults, the scanner reverts to the default state in which it was
shipped from the manufacturer.
HS-360X Handheld DPM Scanner User Manual
10-55
Application Settings
About WebLinkPC
About WebLinkPC opens the dialog below, which shows the current WebLinkPC version,
Browser, Operating System, and Screen Resolution.
Note: The information in this dialog is selectable so that you can copy it to a clipboard.
Clicking Contact Us takes you to the Omron Microscan website.
10-56
HS-360X Handheld DPM Scanner User Manual
WebLinkPC
Advanced Settings
When you click the Gear icon to bring up the Application Settings menu, one of the
options you will see is Advanced.
WebLinkPC's Advanced settings allow you to make fine adjustments to individual command
parameters in all areas of your reader's functionality: Discovery, Misc. Options, Battery,
Statistics, Bluetooth, Radio Comm., Read Cycle, Symbologies, and Imaging. Many of
these commands can be configured directly in the WebLinkPC user interface, but all
parameters can be configured and examined in Advanced settings.
Each menu of Advanced settings commands is shown in the following eight sections, and
an additional section is included that shows an example of the Differences from Default
menu, which shows only commands that are different from WebLinkPC defaults.
HS-360X Handheld DPM Scanner User Manual
10-57
Advanced Settings
Discovery
The Discovery menu shows identifying information about your HS-360X, including Model
Number, Serial Number, and Firmware Version.
Command parameters can be changed directly from this menu.
Discovery Menu
10-58
HS-360X Handheld DPM Scanner User Manual
WebLinkPC
Misc. Options
The Misc. Options menu allows you to configure various aspects of scanner behavior,
such as Beeper Volume, Decode Indicators, and Presentation Target, as well as UID
Parsing and Illumination Control.
Command parameters can be changed directly from this menu.
Misc. Options Menu
HS-360X Handheld DPM Scanner User Manual
10-59
Advanced Settings
Battery
The Battery menu shows several read-only data points about battery identity, health, and
age, and also allows you to set status and health thresholds.
Command parameters can be changed directly from this menu.
Battery Menu
10-60
HS-360X Handheld DPM Scanner User Manual
WebLinkPC
Statistics
The Statistics menu shows read-only information about scanner usage.
Command parameters can be changed directly from this menu.
Statistics Menu
HS-360X Handheld DPM Scanner User Manual
10-61
Advanced Settings
Bluetooth
The Bluetooth menu shows read-only status information and also allows you to configure
the scanner's Bluetooth communications functionality.
Command parameters can be changed directly from this menu.
Bluetooth Menu
10-62
HS-360X Handheld DPM Scanner User Manual
WebLinkPC
Radio Comm.
The Radio Comm. menu shows various radio communications data points, including
information about Bluetooth, pairing, and batch mode.
Command parameters can be changed directly from this menu.
Radio Comm. Menu
HS-360X Handheld DPM Scanner User Manual
10-63
Advanced Settings
Read Cycle
The Read Cycle menu shows all the commands that control all aspects of read cycle,
including triggering, read cycle timing, and image processing.
Command parameters can be changed directly from this menu.
Read Cycle Menu
10-64
HS-360X Handheld DPM Scanner User Manual
WebLinkPC
Symbologies
The Symbologies menu shows all the commands that allow you precise control of the
parameters of all enabled code types. Parameters differ depending on the unique standards
of each code type.
Command parameters can be changed directly from this menu.
Symbologies Menu
Note: The Symbologies menu in Advanced Settings is very long. Refer to the topic
Advanced Settings > Symbologies in WebLinkPC Help for a full-size view of the
Symbologies menu.
HS-360X Handheld DPM Scanner User Manual
10-65
Advanced Settings
Imaging
The Imaging menu allows you to control multiple aspects of image output, including
Image Size in pixels and File Format, as well as image capture parameters such as
Contrast Enhancement and Sub-Sampling.
Command parameters can be changed directly from this menu.
Imaging Menu
10-66
HS-360X Handheld DPM Scanner User Manual
WebLinkPC
Differences from Default
The Differences from Default menu shows only commands whose parameters are not
currently set to WebLinkPC defaults. Commands from any of the nine categories may
appear in this menu.
Command parameters can be changed directly from this menu.
Differences from Default Menu
HS-360X Handheld DPM Scanner User Manual
10-67
Advanced Settings
10-68
HS-360X Handheld DPM Scanner User Manual
Appendices
HS-360X Handheld DPM Scanner User Manual
A-1
Standard Default Parameters
Appendix A — Standard Default Parameters
Parameter
Parameter
Number
Default
383
Cradle Host
Radio Communications
Radio Communications Host Types
BT Friendly Name
607
n/a
Discoverable Mode
610
General
Wi-Fi Friendly Mode
1299
Disable
Wi-Fi Friendly Channel Exclusion
1297
Use All Channels
Radio Output Power
1324
High
Link Supervision Timeout
1698
.5 Seconds
5 Seconds
On
Bluetooth Radio State
1354
Bluetooth HID - Wait for Connection
1714
Disable
HID Features for Apple iOS
1114
Disable
HID Keyboard Keystroke Delay
N/A
No Delay (0 msec)
CAPS Lock Override
N/A
Disable
Ignore Unknown Characters
N/A
Send Barcodes with Unknown
Characters
Emulate Keypad
N/A
Enable
Fast HID Keyboard
1361
Enable
Quick Keypad Emulation
1362
Enable
Keyboard FN1 Substitution
N/A
Disable
Function Key Mapping
N/A
Disable
Simulated Caps Lock
N/A
Disable
Convert Case
N/A
No Case Conversion
Reconnect Attempt Beep Feedback
559
Disable
Reconnect Attempt Interval
558
30 Seconds
Auto-reconnect
604
Auto-reconnect Immediately
Beep on Insertion
288
Enable
Beep on <BEL>
150
Enable
Modes of Operation
(Point-to-Point/
Multipoint-to-Point)
538
Point-to-Point
Parameter Broadcast (Cradle Host Only)
148
Enable
Pairing Modes
542
Unlocked
Pairing Methods
545
Enable
A-2
HS-360X Handheld DPM Scanner User Manual
Appendices
Parameter
Parameter
Number
Default
Toggle Pairing
1322
Disable
Connection Maintenance Interval
5002
15 Minutes
Batch Mode
544
Normal (Do Not Batch Data)
Persistent Batch Storage
1399
Disable
Page Button
746
Enable
Page Options
Page Mode
Page State Timeout
1364
1365
Page Simple
Classic and/or Low Energy Bluetooth
1355
Classic and Low Energy
PIN Code (Set and Store)
552
12345
Variable Pin Code
608
Static (Default PIN code is 12345)
Bluetooth Security Levels
1393
Low
N/A
Restore Defaults
User Preferences
Set Default Parameter
Parameter Barcode Scanning
236
Enable
Beep After Good Decode
56
Enable
Direct Decode Indicator
859
Disable
Beeper Volume
140
High
Beeper Tone
145
Medium
Beeper Duration
628
Medium
Suppress Power Up Beeps
721
Do Not Suppress
Decode Pager Motor
613
Enable
Decode Pager Motor Duration
626
150 msec
Low Power Mode
128
Enable (HS-360X Wireless)
Disable (HS-360X Wired Scanner)
Time Delay to Low Power Mode
146
100 msec (HS-360X Wireless)
1 Hour (HS-360X Wired Scanner)
Timeout to Low Power Mode from Auto Aim
729
(HS-360X Wireless Only)
15 Seconds
Handheld Trigger Mode
138
Level
Hands-free Mode
630
Enable
Handheld Decode Aiming Pattern
306
Enable
Hands-free (Presentation) Decode Aiming
Pattern
590
Enable Hands-free (Presentation)
Decode Aiming Pattern on PDF
Picklist Mode
402
Disabled Always
FIPS Mode (HS-360X Wireless Only)
736
Disable
Continuous Barcode Read
649
Disable
Unique Barcode Reporting
723
Enable
HS-360X Handheld DPM Scanner User Manual
A-3
Standard Default Parameters
Parameter
Parameter
Number
Default
Decode Session Timeout
136
9.9 Seconds
Hands-free Decode Session Timeout
400
15
Timeout Between Decodes, Same Symbol 137
0.5 Seconds
Timeout Between Decodes, Different
Symbols
144
0.5 Seconds
Mobile Phone/Display Mode
716
Normal
PDF Prioritization
719
Disable
PDF Prioritization Timeout
720
200 msec
Decoding Illumination
298
Enable
Motion Tolerance (Handheld Trigger Mode
858
Only)
Battery Threshold
Battery Status High Threshold
Battery Status Medium Threshold
Battery Status Low Warning Threshold
Battery Health Low Warning Threshold
Less
1367
1368
1369
50%
20%
10%
1370
60%
Add an Enter Key
N/A
N/A
Transmit Code ID Character
45
None
Prefix Value
99, 105
7013 <CR><LF>
Suffix 1 Value
Suffix 2 Value
98, 104
100, 106
7013 <CR><LF>
Scan Data Transmission Format
235
Data as is
FN1 Substitution Values
103, 109
7013 <CR><LF>
Transmit “No Read” Message
94
Disable
Unsolicited Heartbeat Interval
1118
Disable
UID
740
Disable
UID Error Mode Options
742
UID Error Beep
Decoder Effort Level
1438
Level 3
DPM Illumination Control
429
Cycle Illumination
N/A
N/A
Imaging Preferences
Operational Modes
Image Size (Number of Pixels)
302
Full
JPEG Image Options
299
Quality
JPEG Target File Size
561
160 kB
JPEG Quality and Size Value
305
65
Image File Format Selection
304
JPEG
Image Rotation
665
0o
A-4
HS-360X Handheld DPM Scanner User Manual
Appendices
Parameter
Number
Default
USB Device Type
N/A
USB Keyboard HID
Symbol Native API (SNAPI) Status
Handshaking
N/A
Enable
USB Keystroke Delay
N/A
No Delay
USB CAPS Lock Override
N/A
Disable
USB Ignore Unknown Characters
N/A
Send Barcodes with Unknown
Characters
Emulate Keypad
N/A
Enable
Emulate Keypad with Leading Zero
N/A
Enable
Quick Keypad Emulation
N/A
Enable
USB FN1 Substitution
N/A
Disable
Parameter
USB Host Parameters
Function Key Mapping
N/A
Disable
Simulated Caps Lock
N/A
Disable
Convert Case
N/A
None
USB Static CDC
N/A
Enable
Ignore Beep Directive
N/A
Enable (Ignore)
Ignore Barcode Configuration
N/A
Enable (Ignore)
USB Polling Interval
N/A
3 msec
USB Fast HID
N/A
Enable
IBM Specification Version
N/A
Version 2.2
RS-232 Host Types
N/A
Standard
Baud Rate
N/A
9600
Parity Type
N/A
None
Stop Bits
N/A
1 Stop Bit
Data Bits
N/A
8-Bit
Check Receive Errors
N/A
Enable
Hardware Handshaking
N/A
None
Software Handshaking
N/A
None
RS-232 Host Parameters
Host Serial Response Time-out
N/A
2 Seconds
RTS Line State
N/A
Low RTS
Beep on <BEL>
N/A
Disable
Intercharacter Delay
N/A
0 msec
Nixdorf Beep/LED Options
N/A
Normal Operation
Ignore Unknown Characters
N/A
Send Barcode
HS-360X Handheld DPM Scanner User Manual
A-5
Standard Default Parameters
Parameter
Parameter
Number
Keyboard Wedge Host Type
N/A
IBM AT Notebook
Ignore Unknown Characters
N/A
Send Barcodes with Unknown
Characters
Keystroke Delay
N/A
No Delay
Intra-Keystroke Delay
N/A
Disable
Default
Alternate Numeric Keypad Emulation
N/A
Enable
Quick Keypad Emulation
N/A
Enable
Simulated Caps Lock
N/A
Disable
Caps Lock Override
N/A
Disable
Convert Wedge Case
N/A
No Convert
Function Key Mapping
N/A
Disable
FN1 Substitution
N/A
Disable
Send Make and Break
N/A
Send Make and Break Scan Codes
UPC-A
1
Enable
UPC-E
2
Enable
Enable/Disable All Code Types
1D Symbologies
UPC/EAN
UPC-E1
12
Disable
EAN-8/JAN 8
4
Enable
EAN-13/JAN 13
3
Enable
Bookland EAN
83
Disable
Decode UPC/EAN/JAN Supplementals
(2 and 5 digits)
16
Ignore
579
580
000
User-Programmable Supplementals
Supplemental 1:
Supplemental 2:
UPC/EAN/JAN Supplemental Redundancy 80
10
Decode UPC/EAN/JAN Supplemental AIM
672
ID
Combined
UPC Reduced Quiet Zone
1289
Disable
Transmit UPC-A Check Digit
40
Enable
Transmit UPC-E Check Digit
41
Enable
Transmit UPC-E1 Check Digit
42
Enable
UPC-A Preamble
34
System Character
UPC-E Preamble
35
System Character
UPC-E1 Preamble
36
System Character
A-6
HS-360X Handheld DPM Scanner User Manual
Appendices
Parameter
Parameter
Number
Default
Convert UPC-E to A
37
Disable
Convert UPC-E1 to A
38
Disable
EAN-8/JAN-8 Extend
39
Disable
Bookland ISBN Format
576
ISBN-10
ISSN EAN
617
Disable
Code 128
Code 128
8
Enable
Set Length(s) for Code 128
209, 210
1 to 55
GS1-128 (formerly UCC/EAN-128)
14
Enable
ISBT 128
84
Disable
ISBT Concatenation
577
Autodiscriminate
Check ISBT Table
578
Enable
ISBT Concatenation Redundancy
223
10
Code 128 Security Level
751
Security Level 1
Code 128 Reduced Quiet Zone
1208
Disable
Ignore Code 128 <FNC4>
1254
Disable
Code 39
Code 39
0
Enable
Trioptic Code 39
13
Disable
Convert Code 39 to Code 32 (Italian
Pharmacy Code)
86
Disable
Code 32 Prefix
231
Disable
Set Length(s) for Code 39
18, 19
1 to 55
Code 39 Check Digit Verification
48
Disable
Transmit Code 39 Check Digit
43
Disable
Code 39 Full ASCII Conversion
17
Disable
Code 39 Security Level
750
Security Level 1
Code 39 Reduced Quiet Zone
1209
Disable
Code 93
9
Enable
Set Length(s) for Code 93
26, 27
1 to 55
Code 11
10
Disable
Set Lengths for Code 11
28, 29
4 to 55
Code 93
Code 11
Code 11 Check Digit Verification
52
Disable
Transmit Code 11 Check Digit(s)
47
Disable
HS-360X Handheld DPM Scanner User Manual
A-5
Standard Default Parameters
Parameter
Parameter
Number
Default
Code 11 Check Digit Verification
52
Disable
Transmit Code 11 Check Digit(s)
47
Disable
6
Disable
Interleaved 2 of 5 (ITF)
Interleaved 2 of 5 (ITF)
Set Lengths for I 2 of 5
22, 23
6 to 55
I 2 of 5 Check Digit Verification
49
Disable
Transmit I 2 of 5 Check Digit
44
Disable
Convert I 2 of 5 to EAN 13
82
Disable
I 2 of 5 Security Level
1121
Security Level 1
I 2 of 5 Reduced Quiet Zone
1210
Disable
Discrete 2 of 5
5
Disable
Set Length(s) for D 2 of 5
20, 21
1 to 55
7
Enable
Discrete 2 of 5 (DTF)
Codabar (NW - 7)
Codabar
Set Lengths for Codabar
24, 25
4 to 55
CLSI Editing
54
Disable
NOTIS Editing
55
Disable
Codabar Upper or Lower Case Start/Stop
Characters Detection
855
Upper Case
MSI
MSI
11
Disable
Set Length(s) for MSI
30, 31
4 to 55
MSI Check Digits
50
One
Transmit MSI Check Digit
46
Disable
MSI Check Digit Algorithm
51
Mod 10/Mod 10
408
Disable
Matrix 2 of 5
618
Disable
Matrix 2 of 5 Lengths
619
620
4 to 55
Matrix 2 of 5 Check Digit
622
Disable
Transmit Matrix 2 of 5 Check Digit
623
Disable
Korean 3 of 5
581
Disable
Inverse 1D
586
Regular
Chinese 2 of 5
Chinese 2 of 5
Matrix 2 of 5
Korean 3 of 5
A-8
HS-360X Handheld DPM Scanner User Manual
Appendices
Parameter
Number
Default
GS1 DataBar-14
338
Enable
GS1 DataBar Limited
339
Enable
GS1 DataBar Expanded
340
Enable
Parameter
GS1 DataBar
Convert GS1 DataBar to UPC/EAN
397
Disable
GS1 DataBar Limited Security Level
728
Level 3
Composite CC-C
341
Disable
Composite CC-A/B
342
Disable
Composite
Composite TLC-39
371
Disable
UPC Composite Mode
344
UPC Never Linked
Composite Beep Mode
398
Beep As Each Code Type is Decoded
GS1-128 Emulation Mode for UCC/EAN
Composite Codes
427
Disable
PDF417
15
Enable
MicroPDF417
227
Disable
Code 128 Emulation
123
Disable
2D Symbologies
Data Matrix
292
Enable
GS1 Data Matrix
1336
Disable
Data Matrix Inverse
588
Inverse Autodetect
Maxicode
294
Disable
QR Code
293
Enable
GS1 QR
1343
Disable
MicroQR
573
Enable
Enable
Aztec
574
Aztec Inverse
589
Inverse Autodetect
Han Xin
1167
Disable
Han Xin Inverse
1168
Regular
US Postnet
89
Disable
US Planet
90
Disable
Postal Codes
Transmit US Postal Check Digit
95
Enable
UK Postal
91
Disable
Transmit UK Postal Check Digit
96
Enable
Japan Postal
290
Disable
HS-360X Handheld DPM Scanner User Manual
A-9
Standard Default Parameters
Parameter
Parameter
Number
Default
Australia Post
291
Disable
Australia Post Format
718
Autodiscriminate
Netherlands KIX Code
326
Disable
USPS 4CB/One Code/Intelligent Mail
592
Disable
UPU FICS Postal
611
Disable
Mailmark
1337
Disable
Redundancy Level
78
1
Security Level
77
1
Symbology-Specific Security Levels
1D Quiet Zone Level
1288
1
Intercharacter Gap Size
381
Normal
Report Version
A-10
HS-360X Handheld DPM Scanner User Manual
Appendices
Appendix B — Country Codes
Introduction
This section provides instructions for programming the keyboard to interface with a USB
host. The host powers the scanner.
To select a code page for the country keyboard type, see Appendix C — Country Code Pages.
USB Country Keyboard Types (Country Codes)
Scan the programming symbol corresponding to the keyboard type. For a USB host, this
setting applies only to the USB Keyboard (HID) device. If the keyboard type is not listed,
see Emulate Keypad for the USB HID host. For a keyboard wedge host, see Alternate
Numeric Keypad Emulation.
Note: When changing USB country keyboard types the scanner automatically resets and
issues the standard startup beep sequences.
Note: For best results when using international keyboards, enable Quick Keypad Emulation.
Note: Some country keyboard programming symbols are specific to certain Windows
Operating Systems (i.e., Windows 7 or higher). Programming symbols requiring a specific
Windows OS are identified in their captions.
Note: Use the French International programming symbol for Belgian French keyboards.
* US English (North American)
US English (Mac)
Albanian
HS-360X Handheld DPM Scanner User Manual
A-11
Country Codes
Arabic (101)
Arabic (102)
Arabic (102) AZERTY
Azeri (Latin)
Azeri (Cyrillic)
A-12
HS-360X Handheld DPM Scanner User Manual
Appendices
Belarusian
Bosnian (Latin)
Bosnian (Cyrillic)
Bulgarian (Latin)
Bulgarian Cyrillic (Typewriter)
(Bulgarian -Windows XP
Typewriter - Win 7 or higher)
HS-360X Handheld DPM Scanner User Manual
A-13
Country Codes
Canadian French Win7
Canadian French (Legacy)
Canadian Multilingual Standard
Chinese (ASCII)
Chinese (Simplified) *
* For CJK keyboard types, see
Appendix D — Chinese,
Japanese, and Korean (CJK)
Decode Control.
Chinese (Traditional) *
A-14
HS-360X Handheld DPM Scanner User Manual
Appendices
Croatian
Czech
Czech (Programmer)
Czech (QWERTY)
Danish
HS-360X Handheld DPM Scanner User Manual
A-15
Country Codes
Dutch (Netherlands)
Estonian
Faeroese
Finnish
French (France)
A-16
HS-360X Handheld DPM Scanner User Manual
Appendices
French International
(Belgian French)
French (Canada) 95/98
French (Canada) 2000/XP *
* Note that there is also a country
code programming symbol for
Canadian Multilingual Standard.
Select the appropriate programming
symbol for your host system.
Galician
German
HS-360X Handheld DPM Scanner User Manual
A-17
Country Codes
Greek Latin
Greek (220) Latin
Greek (319) Latin
Greek
Greek (220)
A-18
HS-360X Handheld DPM Scanner User Manual
Appendices
Greek (319)
Greek Polytonic
Hebrew Israel
Hungarian
Hungarian_101KEY
HS-360X Handheld DPM Scanner User Manual
A-19
Country Codes
Icelandic
Irish
Italian
Italian (142)
Japanese (ASCII)
* For CJK keyboard types, see
Appendix D — Chinese,
Japanese, and Korean (CJK)
Decode Control.
A-20
HS-360X Handheld DPM Scanner User Manual
Appendices
Japanese (SHIFT-JIS) *
Kazakh
Korean (ASCII)
* For CJK keyboard
types, see
Appendix D — Chinese,
Japanese, and Korean
(CJK) Decode Control.
Korean (Hangul) *
Kyrgyz
HS-360X Handheld DPM Scanner User Manual
A-21
Country Codes
Latin American
Latvian
Latvian (QWERTY)
Lithuanian
Lithuanian (IBM)
A-22
HS-360X Handheld DPM Scanner User Manual
Appendices
Macedonian (FYROM)
Maltese_47KEY
Mongolian
Norwegian
Polish (214)
HS-360X Handheld DPM Scanner User Manual
A-23
Country Codes
Polish (Programmer)
Portuguese (Brazil)
(Windows XP)
Portuguese (Brazilian ABNT)
Portuguese (Brazilian ABNT2)
Portuguese (Portugal)
A-24
HS-360X Handheld DPM Scanner User Manual
Appendices
Romanian
(Windows XP)
Romanian (Legacy)
(Win 7 or higher)
Romanian (Standard)
(Win 7 or higher)
Romanian (Programmer)
(Win 7 or higher)
Russian
HS-360X Handheld DPM Scanner User Manual
A-25
Country Codes
Russian (Typewriter)
Serbian (Latin)
Serbian (Cyrillic)
Slovak
Slovak (QWERTY)
A-26
HS-360X Handheld DPM Scanner User Manual
Appendices
Slovenian
Spanish
Spanish (Variation)
Swedish
Swiss French
HS-360X Handheld DPM Scanner User Manual
A-27
Country Codes
Swiss German
Tatar
Thai (Kedmanee)
Turkish F
Turkish Q
A-28
HS-360X Handheld DPM Scanner User Manual
Appendices
UK English
Ukrainian
US Dvorak
US Dvorak Left
US Dvorak Right
HS-360X Handheld DPM Scanner User Manual
A-29
Country Codes
US International
Uzbek
Vietnamese
A-30
HS-360X Handheld DPM Scanner User Manual
Appendices
Appendix C — Country Code Pages
Introduction
This chapter provides programming symbols for selecting code pages for the country
keyboard type selected in Appendix A — Standard Default Parameters. If the default
code page in the table below is appropriate for your selected country keyboard type, you
do not need to scan a country code page programming symbol.
Country Code Page Defaults
The table below lists the code page default for each country keyboard.
Country Keyboard
Code Page Default
US English (North American)
Windows 1252
US English (Mac)
Mac CP10000
Albanian
Windows 1250
Arabic 101
Windows 1256
Arabic 102
Windows 1256
Arabic 102 AZERTY
Windows 1256
Azeri Latin
Windows 1254
Azeri Cyrillic
Windows 1251
Belarusian
Windows 1251
Bosnian Latin
Windows 1250
Bosnian Cyrillic
Windows 1251
Bulgarian Latin
Windows 1250
Bulgarian Cyrillic
Windows 1251
Canadian French Win7
Windows 1252
Canadian French (Legacy)
Windows 1252
Canadian Multilingual
Windows 1252
Croatian
Windows 1250
Chinese ASCII
Windows 1252
Chinese (Simplified)
Windows 936, GBK
Chinese (Traditional)
Windows 950, Big5
Czech
Windows 1250
Czech Programmers
Windows 1250
Czech QWERTY
Windows 1250
Danish
Windows 1252
Dutch Netherland
Windows 1252
Estonian
Windows 1257
Faeroese
Windows 1252
HS-360X Handheld DPM Scanner User Manual
A-31
Country Code Pages
Country Keyboard
Code Page Default
Finnish
Windows 1252
French (France)
Windows 1252
French (Canada) 95/98
Windows 1252
French (Canada) 2000/XP
Windows 1252
French International (Belgian French)
Windows 1252
Galician
Windows 1252
German
Windows 1252
Greek Latin
Windows 1252
Greek220 Latin
Windows 1253
Greek319 Latin
Windows 1252
Greek
Windows 1253
Greek220
Windows 1253
Greek319
Windows 1253
Greek Polytonic
Windows 1253
Hebrew Israel
Windows 1255
Hungarian
Windows 1250
Hungarian_101KEY
Windows 1250
Icelandic
Windows 1252
Irish
Windows 1252
Italian
Windows 1252
Italian_142
Windows 1252
Japanese ASCII
Windows 1252
Japanese (Shift-JIS)
Windows 932, Shift-JIS
Kazakh
Windows 1251
Korean ASCII
Windows 1252
Korean (Hangul)
Windows 949, Hangul
Kyrgyz Cyrillic
Windows 1251
Latin America
Windows 1252
Latvian
Windows 1257
Latvian QWERTY
Windows 1257
Lithuanian
Windows 1257
Lithuanian_IBM
Windows 1257
Macedonian -FYROM
Windows 1251
Maltese_47KEY
Windows 1252
Mongolian-Cyrillic
Windows 1251
Norwegian
Windows 1252
A-32
HS-360X Handheld DPM Scanner User Manual
Appendices
Country Keyboard
Code Page Default
Polish_214
Windows 1250
Polish Programmer
Windows 1250
Portuguese Brazil
Windows 1252
Portuguese Brazilian ABNT
Windows 1252
Portuguese Brazilian ABNT2
Windows 1252
Portuguese Portugal
Windows 1252
Romanian
Windows 1250
Romanian Legacy
Windows 1250
Romanian Standard
Windows 1250
Romanian Programmer
Windows 1250
Russian
Windows 1251
Russian Typewriter
Windows 1251
Serbian Latin
Windows 1250
Serbian Cyrillic
Windows 1251
Slovak
Windows 1250
Slovak QWERTY
Windows 1250
Slovenian
Windows 1250
Spanish
Windows 1252
Spanish Variation
Windows 1252
Swedish
Windows 1252
Swiss French
Windows 1252
Swiss German
Windows 1252
Tatar
Windows 1251
Thai-Kedmanee
Windows 874
Turkish F
Windows 1254
Turkish Q
Windows 1254
Ukrainian
Windows 1251
United Kingdom
Windows 1252
United States
Windows 1252
US Dvorak
Windows 1252
US Dvorak Left Hand
Windows 1252
US Dvorak Right Hand
Windows 1252
US International
Windows 1252
Uzbek Cyrillic
Windows 1251
Vietnamese
Windows 1258
HS-360X Handheld DPM Scanner User Manual
A-33
Country Code Pages
Country Code Page Barcodes
Scan the programming symbol corresponding to the country keyboard code page.
Windows 1250
Latin 2, Central European
Windows 1251
Cyrillic, Slavic
Windows 1252
Latin 1, Western European
Windows 1253
Greek
A-34
HS-360X Handheld DPM Scanner User Manual
Appendices
Windows 1254
Latin 5, Turkish
Windows 1255
Hebrew
Windows 1256
Arabic
Windows 1257
Baltic
Windows 1258
Vietnamese
HS-360X Handheld DPM Scanner User Manual
A-35
Country Code Pages
Windows 874
Thai
Windows 20866
Cyrillic KOI8-R
Windows 932
Japanese Shift-JIS
Windows 936
Simplified Chinese GBK
Windows 54936
Simplified Chinese GB18030
A-36
HS-360X Handheld DPM Scanner User Manual
Appendices
Windows 949
Korean Hangul
Windows 950
Traditional Chinese Big5
MS-DOS 437
Latin US
MS-DOS 737
Greek
MS-DOS 775
Baltic
HS-360X Handheld DPM Scanner User Manual
A-37
Country Code Pages
MS-DOS 850
Latin 1
MS-DOS 852
Latin 2
MS-DOS 855
Cyrillic
MS-DOS 857
Turkish
MS-DOS 860
Portuguese
A-38
HS-360X Handheld DPM Scanner User Manual
Appendices
MS-DOS 861
Icelandic
MS-DOS 862
Hebrew
MS-DOS 863
Canadian French
MS-DOS 865
Nordic
MS-DOS 866
Cyrillic
HS-360X Handheld DPM Scanner User Manual
A-39
Country Code Pages
MS-DOS 869
Greek 2
ISO 8859-1
Latin 1, Western European
ISO 8859-2
Latin 2, Central European
ISO 8859-3
Latin 3, Southern European
ISO 8859-4
Latin 4, Northern European
A-40
HS-360X Handheld DPM Scanner User Manual
Appendices
ISO 8859-5
Cyrillic
ISO 8859-6
Arabic
ISO 8859-7
Greek
ISO 8859-8
Hebrew
ISO 8859-9
Latin 5, Turkish
HS-360X Handheld DPM Scanner User Manual
A-41
Country Code Pages
ISO 8859-10
Latin 6, Nordic
ISO 8859-11
Thai
ISO 8859-13
Latin 7, Baltic
ISO 8859-14
Latin 8, Celtic
ISO 8859-15
Latin 9
A-42
HS-360X Handheld DPM Scanner User Manual
Appendices
ISO 8859-16
Latin 10, South-Eastern European
UTF-8
UTF-16LE
UTF-16 Little Endian
UTF-16BE
UTF-16 Big Endian
Mac CP10000
Roman
HS-360X Handheld DPM Scanner User Manual
A-43
Chinese, Japanese, and Korean (CJK) Decode Control
Appendix D — Chinese, Japanese, and Korean
(CJK) Decode Control
Introduction
This appendix describes control parameters for CJK (Chinese, Japanese, Korean) barcode
decoding through USB HID Keyboard Emulation mode.
CJK Control Parameters – Unicode Output Control
Parameter # 973
For a Unicode-encoded CJK barcode, select one of the following options for unicode output:
• Universal Output to Unicode and MBCS Application - This default method applies to Unicode
and MBCS expected applications, such as MS Word and Notepad on a Windows host.
Note: To support Unicode universal output, set up the registry table for the Windows host.
• Output to Unicode Application Only - This method applies only to Unicode-expected
applications, such as MS Word and WordPad, but not Notepad.
* Universal Output
(0)
Unicode Application Only
(1)
A-44
HS-360X Handheld DPM Scanner User Manual
Appendices
CJK Output Method to Windows Host
Parameter # 972
For a national standard encoded CJK barcode, select one of the following options for CJK
output to a Windows host:
• Universal CJK Output - This is the default universal CJK output method for US English
IME or Chinese/Japanese/Korean ASCII IME on a Windows host. This method converts
CJK characters to Unicode and emulates the characters when transmitting to the host.
Use the Unicode Output Control parameter to control Unicode output.
Note: To support universal CJK output, set up the registry table for the Windows host.
See Unicode/CJK Decode Setup with Windows Host.
• Other options for CJK output - With the following methods, the scanner sends the
CJK character hexadecimal internal code (Nei Ma) value to host, or converts the CJK
character to Unicode and sends the hexadecimal Unicode value to host. When using
these methods, the Windows host must select the corresponding IME to accept the CJK
character. See Unicode/CJK Decode Setup with Windows Host.
•
•
•
•
•
•
•
•
Japanese Unicode Output
Simplified Chinese GBK Code Output
Simplified Chinese Unicode Output
Korean Unicode Code Output
Traditional Chinese Big5 Code Output (Windows XP)
Traditional Chinese Big5 Code Output (Windows 7)
Traditional Chinese Unicode Code Output (Windows XP)
Traditional Chinese Unicode Code Output (Windows 7)
Note: The Unicode emulate output method depends on the host system (Windows XP
or Windows 7).
* Universal CJK Output
(0)
HS-360X Handheld DPM Scanner User Manual
A-45
Chinese, Japanese, and Korean (CJK) Decode Control
Japanese Unicode Output
(34)
(For Japanese Unicode Output,
select Simplified Chinese Unicode
IME on the Windows host.)
Chinese (Simplified) GBK Output
(1)
Chinese (Simplified) Unicode Output
(2)
Korean Unicode Output
(50)
(For Korean Unicode Output,
select Simplified Chinese Unicode
IME on the Windows host.)
A-46
HS-360X Handheld DPM Scanner User Manual
Appendices
Chinese (Traditional) Big5 Output
(Windows XP) (17)
Chinese (Traditional) Big5 Output
(Windows 7)
(19)
Chinese (Traditional) Unicode Output
(Windows XP)
(18)
Chinese (Traditional) Unicode Output
(Windows 7)
(20)
HS-360X Handheld DPM Scanner User Manual
A-47
Chinese, Japanese, and Korean (CJK) Decode Control
Non-CJK UTF Barcode Output
Parameter # 960
Some country keyboard type layouts contain characters that do not exist in the default
code page (see Country Keyboard Type Missing Characters on the next page).
Although the default code page can not encode these characters in a barcode, they can
be encoded in the UTF-8 barcode. Scan this parameter programming symbol to output the
Unicode values by emulation mode.
Note: Use this special country keyboard type to decode the non-CJK UTF-8 barcode.
After decoding, re-configure the scanner to use the original country keyboard type.
Use US English IME on Windows.
Non-CJK UTF-8 Emulation Output
A-48
HS-360X Handheld DPM Scanner User Manual
Appendices
Country Keyboard Type Missing Characters
Country keyboard type: Tatar, Uzbek, Mongolian, Kyrgyz, Kazakh and Azeri
Default code page: CP1251
Missing characters:
ғ
Ғ
ҳ
Ҳ
қ
Қ
һ
Һ
ө
Ө
ə
Ə
ү
Ү
ң
Ң
җ
₮
Җ
ң
Ң
ұ
Ұ
қ
Қ
ҹ
Ҹ
ҝ
Ҝ
Country keyboard type: Romanian (Standard)
Default code page: CP1250
Missing characters:
ș
ț
Ș
Ț
Country keyboard type: Portuguese-Brazilian (ABNT), Portuguese-Brazilian (ABNT2)
Default code page: CP1252
Missing character: ₢
Country keyboard type: Azeri-Latin
Default code page: CP1254
Missing characters: ə, Ə
HS-360X Handheld DPM Scanner User Manual
A-49
Chinese, Japanese, and Korean (CJK) Decode Control
Unicode/CJK Decode Setup with Windows Host
This section describes how to set up CJK decode with a Windows host.
Setting Up the Windows Registry Table for Unicode Universal Output
To support the Unicode universal output method, set up the Windows host registry table as follows:
1. Select Start > Run > regedt32 to start the registry editor.
2. Under HKEY_Current_User\Control Panel\Input Method, set EnableHexNumpad
to 1 as follows:
[HKEY_CURRENT_USER\Control Panel\Input Method]
"EnableHexNumpad"="1"
If this key does not exist, add it as type REG_SZ (string value).
3. Reboot the computer to implement the registry change.
Adding CJK IME on Windows
To add the desired CJK input language:
1. Click Start > Control Panel.
2. If the Control Panel opens in category view, select Switch to Classic View in the top
left corner.
3. Select Regional and Language Options.
4. Click the Language tab.
5. Under Supplemental Language Support, select the Install Files for East Asian
Languages check box if not already selected, and click Apply. This may require a
Windows installation CD to install the required files. This step ensures that the East
Asian Languages (CJK) are available.
6. Under Text Services and Input Language, click Details.
7. Under Installed Services, click Add.
8. In the Add Input Language dialog box, choose the CJK input language and keyboard
layout or Input Method Editor (IME) to add.
9. Click OK twice. The language indicator appears in the system tray (at bottom right corner
of the desktop by default). To switch between input languages (keyboard languages)
select the language indicator in the system tray.
10. Select the language indicator in the system tray to select the desired country keyboard type.
11. Verify that the characters displayed on each country's keyboard appear.
A-50
HS-360X Handheld DPM Scanner User Manual
Appendices
Selecting the Simplified Chinese Input Method on the Host
To select the Simplified Chinese input method:
• Select Unicode/GBK input on Windows XP: Chinese (Simplified) - NeiMa, then click
the input bar to select Unicode or GBK NeiMa input.
or
Unicode/GBK Input on Windows XP
• Select Unicode/GBK input on Windows 7: Chinese (Simplified) - Microsoft Pinyin
New Experience Input Style, then select Tool Menu > Secondary Inputs > Unicode
Input or GB Code Input.
Unicode/GBK Input on Windows 7
HS-360X Handheld DPM Scanner User Manual
A-51
Chinese, Japanese, and Korean (CJK) Decode Control
Selecting the Traditional Chinese Input Method on the Host
To select the Traditional Chinese input method:
• Select Unicode input on Windows XP: Chinese (Traditional) - Unicode
• Select Big5 input on Windows XP: Chinese (Traditional) - Big5 Code
• Select Unicode/Big5 input on Windows 7: Chinese (Traditional) - New Quick. This option
support both Unicode and Big5 input.
A-52
HS-360X Handheld DPM Scanner User Manual
Appendices
Appendix E — Programming Reference
Symbology Identifiers
Code Character
A
B
C
D
E
F
G
H
J
K
L
M
N
R
S
T
U
V
X
z
P00
P01
P02
P03
P04
P05
P06
P08
P09
P0A
P0B
P0C
P0H
P0G
P0Q
P0X
Code Type
UPC-A, UPC-E, UPC-E1, EAN-8, EAN-13
Code 39, Code 32
Codabar
Code 128, ISBT 128, ISBT 128 Concatenated
Code 93
Interleaved 2 of 5
Discrete 2 of 5, or Discrete 2 of 5 IATA
Code 11
MSI
GS1-128
Bookland EAN
Trioptic Code 39
Coupon Code
GS1 DataBar Family
Matrix 2 of 5
UCC Composite, TLC 39
Chinese 2 of 5
Korean 3 of 5
ISSN EAN, PDF417, Macro PDF417, Micro PDF417
Aztec, Aztec Rune
Data Matrix
QR Code, MicroQR
Maxicode
US Postnet
US Planet
Japan Postal
UK Postal
Netherlands KIX Code
Australia Post
USPS 4CB/One Code/Intelligent Mail
UPU FICS Postal
Mailmark
Han Xin
GS1 Data Matrix
GS1 QR
Signature Capture
HS-360X Handheld DPM Scanner User Manual
A-53
Programming Reference
AIM Code Identifiers
Each AIM Code Identifier contains the three-character string ]cm where:
] = Flag Character (ASCII 93)
c = Code Character
m = Modifier Character
Code Character
Code Type
A
Code 39, Code 39 Full ASCII, Code 32
C
Code 128, ISBT 128, ISBT 128 Concatenated, GS1-128,
Coupon (Code 128 portion)
d
Data Matrix, GS1-DM
E
UPC/EAN, Coupon (UPC portion)
e
GS1 DataBar Family
F
Codabar
G
Code 93
H
Code 11
h
Han Xin
I
Interleaved 2 of 5
L
PDF417, Macro PDF417, Micro PDF417
L2
TLC 39
M
MSI
Q
QR Code, MicroQR, GS1-QR
S
Discrete 2 of 5, IATA 2 of 5
U
Maxicode
z
Aztec, Aztec Rune
X
Bookland EAN, ISSN EAN, Trioptic Code 39, Chinese 2 of 5,
Matrix 2 of 5, Korean 3 of 5, US Postnet, US Planet, UK Postal, Japan Postal,
Australia Post, Netherlands KIX Code, USPS 4CB/One Code/ Intelligent Mail,
UPU FICS Postal, Signature Capture, Mailmark
A-54
HS-360X Handheld DPM Scanner User Manual
Appendices
Modifier Characters
The modifier character is the sum of the applicable option values based on the table below.
Code Type
Code 39
Option Value
Option
0
No check character or Full ASCII processing.
1
Reader has checked one check character.
3
Reader has checked and stripped check character.
4
Reader has performed Full ASCII character conversion.
5
Reader has performed Full ASCII character conversion and
checked one check character.
7
Reader has performed Full ASCII character conversion and
checked and stripped check character.
Example: A Full ASCII barcode with check character W, A+I+MI+DW, is transmitted
as ]A7AIMID where 7 = (3+4).
Trioptic Code 39
Mailmark
Code 128
0
No option specified at this time. Always transmit 0.
Example: A Trioptic barcode 412356 is transmitted as ]X0412356
0
No option specified at this time. Always transmit 0.
0
Standard data packet, no Function code 1 in first symbol position.
1
Function code 1 in first symbol character position.
2
Function code 1 in second symbol character position.
Example: A Code (EAN) 128 barcode with Function 1 character FNC1 in the first
position, AIMID is transmitted as ]C1AIMID
I 2 of 5
0
No check digit processing.
1
Reader has validated check digit.
3
Reader has validated and stripped check digit.
Example: An I 2 of 5 barcode without check digit, 4123, is transmitted as ]I04123
Codabar
0
No check digit processing.
1
Reader has checked check digit.
3
Reader has stripped check digit before transmission.
Example: A Codabar barcode without check digit, 4123, is transmitted as ]F04123
Code 93
MSI
D 2 of 5
0
No options specified at this time. Always transmit 0.
Example: A Code 93 barcode 012345678905 is transmitted as ]G0012345678905
0
Check digits are sent.
1
No check digit is sent.
Example: An MSI barcode 4123, with a single check digit checked, is transmitted as
]M14123
0
No options specified at this time. Always transmit 0.
Example: A D 2 of 5 barcode 4123, is transmitted as ]S04123
HS-360X Handheld DPM Scanner User Manual
A-55
Programming Reference
Code Type
UPC/EAN
Option Value
Option
0
Standard data packet in full EAN format, i.e. 13 digits for UPC-A,
UPC-E, and EAN-13 (not including supplemental data).
1
Two digit supplemental data only.
2
Five digit supplemental data only.
3
Combined data packet comprising 13 digits from EAN-13, UPC-A
or UPC-E symbol and 2 or 5 digits from supplemental symbol.
4
EAN-8 data packet.
Example: A UPC-A barcode 012345678905 is transmitted as ]E00012345678905
Bookland EAN
ISSN EAN
Code 11
0
No options specified at this time. Always transmit 0.
Example: A Bookland EAN barcode 123456789X is transmitted as ]X0123456789X
0
No options specified at this time. Always transmit 0.
Example: An ISSN EAN barcode 123456789X is transmitted as ]X0123456789X
0
Single check digit
1
Two check digits
3
Check characters validated but not transmitted.
No option specified at this time. Always transmit 0. GS1 DataBar14 and GS1 DataBar Limited transmit with an Application Identifier
“01”.
Note: In GS1-128 emulation mode, GS1 DataBar is transmitted
using Code 128 rules (i.e., ]C1).
GS1 DataBar
Family
Example: A GS1 DataBar-14 barcode 0110012345678902 is transmitted as
]e00110012345678902.
Native mode transmission.
Note: UPC portion of composite is transmitted using UPC rules.
0
1
EAN.UCC
Composites (GS1
2
DataBar, GS1-128,
2D portion of UPC
composite)
3
Standard data packet.
Data packet containing the data following an encoded symbol
separator character.
Data packet containing the data following an escape mechanism
character. The data packet does not support the ECI protocol.
Data packet containing the data following an escape mechanism
character. The data packet supports the ECI protocol.
GS1-128 emulation
Note: UPC portion of composite is transmitted using UPC rules.
1
A-56
Data packet is a GS1-128 symbol (i.e., data is preceded with
]JC1).
HS-360X Handheld DPM Scanner User Manual
Appendices
Code Type
PDF417,
Micro PDF417
Option Value
Option
0
Reader set to conform to protocol defined in 1994 PDF417
symbology specifications. Note: When this option is transmitted,
the receiver cannot reliably determine whether ECIs have been
invoked or whether data byte 92DEC has been doubled in
transmission.
1
Reader set to follow the ECI protocol (Extended Channel
Interpretation). All data characters 92DEC are doubled.
2
Reader set for Basic Channel operation (no escape character
transmission protocol). Data characters 92DEC are not doubled.
Note: When decoders are set to this mode, unbuffered Macro
symbols and symbols requiring the decoder to convey ECI escape
sequences cannot be transmitted.
3
The barcode contains a GS1-128 symbol, and the first codeword
is 903-907, 912, 914, 915.
4
The barcode contains a GS1-128 symbol, and the first codeword
is in the range 908-909.
5
The barcode contains a GS1-128 symbol, and the first codeword
is in the range 910-911.
Example: A PDF417 barcode ABCD, with no transmission protocol enabled, is
transmitted as ]L2ABCD.
Data Matrix
GS1 Data Matrix
MaxiCode
0
ECC 000-140, not supported.
1
ECC 200.
2
ECC 200, FNC1 in first or fifth position.
3
ECC 200, FNC1 in second or sixth position.
4
ECC 200, ECI protocol implemented.
5
ECC 200, FNC1 in first or fifth position, ECI protocol implemented.
6
ECC 200, FNC1 in second or sixth position, ECI protocol
implemented.
2
ECC 200, FNC1 in first or fifth position.
0
Symbol in Mode 4 or 5.
1
Symbol in Mode 2 or 3.
2
Symbol in Mode 4 or 5, ECI protocol implemented.
3
Symbol in Mode 2 or 3, ECI protocol implemented in secondary
message.
HS-360X Handheld DPM Scanner User Manual
A-57
Programming Reference
Code Type
QR Code
GS1 QR
Aztec
Option Value
Option
0
Model 1 symbol.
1
Model 2 / MicroQR symbol, ECI protocol not implemented.
2
Model 2 symbol, ECI protocol implemented.
3
Model 2 symbol, ECI protocol not implemented, FNC1 implied in
first position.
4
Model 2 symbol, ECI protocol implemented, FNC1 implied in first
position.
5
Model 2 symbol, ECI protocol not implemented, FNC1 implied in
second position.
6
Model 2 symbol, ECI protocol implemented, FNC1 implied in
second position.
3
Model 2 symbol, ECI protocol not implemented, FNC1 implied in
first position.
0
Aztec symbol.
C
Aztec Rune symbol.
0
Generic data, no special features are set. The transmitted data
does not follow the AIM ECI protocol.
1
ECI protocol enabled. There is at least one ECI mode encoded.
Transmitted data must follow the AIM ECI protocol.
Han Xin
A-58
HS-360X Handheld DPM Scanner User Manual
Appendices
Appendix F — Sample Symbols
Code 39
123ABC
UPC/EAN
UPC-A, 100%
0
12345 67890
5
EAN-13, 100%
3 456789 012340
Code 128
1234567890
HS-360X Handheld DPM Scanner User Manual
A-59
Sample Symbols
Interleaved 2 of 5
12345678901231
GS1 DataBar-14
DataBar-14 must be enabled to read the barcode below.
PDF417
Data Matrix
Maxicode
A-60
HS-360X Handheld DPM Scanner User Manual
Appendices
QR Code
US Postnet
UK Postal
HS-360X Handheld DPM Scanner User Manual
A-61
Alphanumeric Keyboard
Appendix G — Alphanumeric Keyboard
Alphanumeric Programming Symbols
Space
#
$
%
*
+
A-62
HS-360X Handheld DPM Scanner User Manual
Appendices
-
.
/
!
“
&
‘
HS-360X Handheld DPM Scanner User Manual
A-63
Alphanumeric Keyboard
(
)
:
;
<
=
>
A-64
HS-360X Handheld DPM Scanner User Manual
Appendices
?
@
[
\
]
^
_
HS-360X Handheld DPM Scanner User Manual
`
A-65
Alphanumeric Keyboard
Important: Do not confuse the following programming symbols with those on the numeric keypad.
0
1
2
3
4
5
6
A-66
HS-360X Handheld DPM Scanner User Manual
Appendices
7
8
9
End of Message
Cancel
A
HS-360X Handheld DPM Scanner User Manual
A-67
Alphanumeric Keyboard
B
C
D
E
F
G
A-68
HS-360X Handheld DPM Scanner User Manual
Appendices
H
I
J
K
L
M
HS-360X Handheld DPM Scanner User Manual
A-69
Alphanumeric Keyboard
N
O
P
Q
R
S
A-70
HS-360X Handheld DPM Scanner User Manual
Appendices
T
U
V
W
X
Y
HS-360X Handheld DPM Scanner User Manual
A-71
Alphanumeric Keyboard
Z
a
b
c
d
e
A-72
HS-360X Handheld DPM Scanner User Manual
Appendices
f
g
h
i
j
k
HS-360X Handheld DPM Scanner User Manual
A-73
Alphanumeric Keyboard
l
m
n
o
p
q
A-74
HS-360X Handheld DPM Scanner User Manual
Appendices
r
s
t
u
v
w
HS-360X Handheld DPM Scanner User Manual
A-75
Alphanumeric Keyboard
x
y
z
{
|
}
~
A-76
HS-360X Handheld DPM Scanner User Manual
Appendices
Appendix H — Numeric Keyboard
Numeric Programming Symbols
For parameters requiring specific numeric values, scan the appropriately numbered programming
symbol(s).
0
1
2
3
4
HS-360X Handheld DPM Scanner User Manual
A-77
Numeric Keyboard
5
6
7
8
9
Cancel
To correct an error or change a selection, scan the programming symbol below.
Cancel
A-78
HS-360X Handheld DPM Scanner User Manual
Appendices
Appendix I — ASCII Character Sets
Full ASCII Code 39
Encode Char
Keystroke
1000
%U
CTRL 2
1001
$A
CTRL A
1002
$B
CTRL B
1003
$C
CTRL C
1004
$D
CTRL D
1005
$E
CTRL E
1006
$F
CTRL F
1007
$G
CTRL G
1008
$H
CTRL H/BACKSPACE1
1009
$I
CTRL I/HORIZONTAL TAB1
1010
$J
CTRL J
1011
$K
CTRL K
1012
$L
CTRL L
1013
$M
CTRL M/ENTER1
1014
$N
CTRL N
1015
$O
CTRL O
1016
$P
CTRL P
1017
$Q
CTRL Q
1018
$R
CTRL R
1019
$S
CTRL S
1020
$T
CTRL T
1021
$U
CTRL U
1022
$V
CTRL V
1023
$W
CTRL W
1024
$X
CTRL X
1025
$Y
CTRL Y
1026
$Z
CTRL Z
1027
%A
CTRL [
1028
%B
CTRL \
ASCII Value
1029
%C
CTRL ]
1030
%D
CTRL 6
1031
%E
CTRL -
The keystroke in bold transmits only if you enabled Function Key Mapping. Otherwise, the non-bold
keystroke transmits.
HS-360X Handheld DPM Scanner User Manual
A-79
ASCII Character Sets
ASCII Value
Full ASCII Code 39
Encode Char
Keystroke
1032
Space
Space
1033
/A
!
1034
/B
“
1035
/C
#
1036
/D
$
1037
/E
%
1038
/F
&
1039
/G
‘
1040
/H
(
1041
/I
)
1042
/J
*
1043
/K
+
1044
/L
,
1045
-
-
1046
.
.
1047
/o
/
1048
0
0
1049
1
1
1050
2
2
1051
3
3
1052
4
4
1053
5
5
1054
6
6
1055
7
7
1056
8
8
1057
9
9
1058
/Z
:
1059
%F
;
1060
%G
<
1061
%H
=
1062
%I
>
1063
%J
?
1064
%V
@
1065
A
A
The keystroke in bold transmits only if you enabled Function Key Mapping. Otherwise, the non-bold
keystroke transmits.
A-80
HS-360X Handheld DPM Scanner User Manual
Appendices
ASCII Value
Full ASCII Code 39
Encode Char
Keystroke
1066
B
B
1067
C
C
1068
D
D
1069
E
E
1070
F
F
1071
G
G
1072
H
H
1073
I
I
1074
J
J
1075
K
K
1076
L
L
1077
M
M
1078
N
N
1079
O
O
1080
P
P
1081
Q
Q
1082
R
R
1083
S
S
1084
T
T
1085
U
U
1086
V
V
1087
W
W
1088
X
X
1089
Y
Y
1090
Z
Z
1091
%K
[
1092
%L
\
1093
%M
]
1094
%N
^
1095
%O
_
1096
%W
‘
1097
+A
a
1098
+B
b
1099
+C
c
The keystroke in bold transmits only if you enabled Function Key Mapping. Otherwise, the non-bold
keystroke transmits.
HS-360X Handheld DPM Scanner User Manual
A-81
ASCII Character Sets
ASCII Value
Full ASCII Code 39
Encode Char
Keystroke
1100
+D
d
1101
+E
e
1102
+F
f
1103
+G
g
1104
+H
h
1105
+I
i
1106
+J
j
1107
+K
k
1108
+L
l
1109
+M
m
1110
+N
n
1111
+O
o
1112
+P
p
1113
+Q
q
1114
+R
r
1115
+S
s
1116
+T
t
1117
+U
u
1118
+V
v
1119
+W
w
1120
+X
x
1121
+Y
y
1122
+Z
z
1123
%P
{
1124
%Q
I
1125
%R
}
1126
%S
~
1127
Undefined
The keystroke in bold transmits only if you enabled Function Key Mapping. Otherwise, the non-bold
keystroke transmits.
ALT Keys
Keystroke
2050
ALT 2
2054
ALT 6
2064
ALT @
2065
ALT A
2066
ALT B
A-82
HS-360X Handheld DPM Scanner User Manual
Appendices
ALT Keys
Keystroke
2067
ALT C
2068
ALT D
2069
ALT E
2070
ALT F
2071
ALT G
2072
ALT H
2073
ALT I
2074
ALT J
2075
ALT K
2076
ALT L
2077
ALT M
2078
ALT N
2079
ALT O
2080
ALT P
2081
ALT Q
2082
ALT R
2083
ALT S
2084
ALT T
2085
ALT U
2086
ALT V
2087
ALT W
2088
ALT X
2089
ALT Y
2090
ALT Z
2091
ALT [
2092
ALT \
2093
ALT ]
GUI Key
Keystroke
3000
Right Control Key
3001
PA 1
3002
PA 2
3003
CMD 1
3004
CMD 2
3005
CMD 3
Note: GUI Shift Keys - The Apple™ iMac keyboard has an apple key on either side of the space bar.
Windows-based systems have a GUI key to the left of the left ALT key, and to the right of the right
ALT key.
HS-360X Handheld DPM Scanner User Manual
A-83
ASCII Character Sets
GUI Key
Keystroke
3006
CMD 4
3007
CMD 5
3008
CMD 6
3009
CMD 7
3010
CMD 8
3011
CMD 9
3012
CMD 10
3013
CMD 11
3014
CMD 12
3015
CMD 13
3016
CMD 14
3048
GUI 0
3049
GUI 1
3050
GUI 2
3051
GUI 3
3052
GUI 4
3053
GUI 5
3054
GUI 6
3055
GUI 7
3056
GUI 8
3057
GUI 9
3065
GUI A
3066
GUI B
3067
GUI C
3068
GUI D
3069
GUI E
3070
GUI F
3071
GUI G
3072
GUI H
3073
GUI I
3074
GUI J
3075
GUI K
3076
GUI L
3077
GUI M
Note: GUI Shift Keys - The Apple™ iMac keyboard has an apple key on either side of the space bar.
Windows-based systems have a GUI key to the left of the left ALT key, and to the right of the right
ALT key.
A-84
HS-360X Handheld DPM Scanner User Manual
Appendices
GUI Key
Keystroke
3078
GUI N
3079
GUI O
3080
GUI P
3081
GUI Q
3082
GUI R
3083
GUI S
3084
GUI T
3085
GUI U
3086
GUI V
3087
GUI W
3088
GUI X
3089
GUI Y
3090
GUI Z
Note: GUI Shift Keys - The Apple™ iMac keyboard has an apple key on either side of the space bar.
Windows-based systems have a GUI key to the left of the left ALT key, and to the right of the right
ALT key.
HS-360X Handheld DPM Scanner User Manual
A-85
ASCII Character Sets
PF Keys
Keystroke
4001
PF 1
4002
PF 2
4003
PF 3
4004
PF 4
4005
PF 5
4006
PF 6
4007
PF 7
4008
PF 8
4009
PF 9
4010
PF 10
4011
PF 11
4012
PF 12
4013
PF 13
4014
PF 14
4015
PF 15
4016
PF 16
A-86
HS-360X Handheld DPM Scanner User Manual
Appendices
F Keys
Keystroke
5001
F1
5002
F2
5003
F3
5004
F4
5005
F5
5006
F6
5007
F7
5008
F8
5009
F9
5010
F 10
5011
F 11
5012
F 12
5013
F 13
5014
F 14
5015
F 15
5016
F 16
5017
F 17
5018
F 18
5019
F 19
5020
F 20
5021
F 21
5022
F 22
5023
F 23
5024
F 24
HS-360X Handheld DPM Scanner User Manual
A-87
ASCII Character Sets
Numeric Keypad
Keystroke
6042
*
6043
+
6044
Undefined
6045
-
6046
.
6047
/
6048
0
6049
1
6050
2
6051
3
6052
4
6053
5
6054
6
6055
7
6056
8
6057
9
6058
Enter
6059
Num Lock
A-88
HS-360X Handheld DPM Scanner User Manual
Appendices
Extended Keypad
Keystroke
7001
Break
7002
Delete
7003
Pg Up
7004
End
7005
Pg Dn
7006
Pause
7007
Scroll Lock
7008
Backspace
7009
Tab
7010
Print Screen
7011
Insert
7012
Home
7013
Enter
7014
Escape
7015
Up Arrow
7016
Dn Arrow
7017
Left Arrow
7018
Right Arrow
HS-360X Handheld DPM Scanner User Manual
A-89
Non-Parameter Attributes
Appendix J — Non-Parameter Attributes
Introduction
This appendix defines non-parameter attributes.
Attributes
Model Number
Attribute #533
Model number of the scanner. This electronic output matches the printout on the physical
device label, for example LI2208-SR00006ZZWW.
Type
S
Size (Bytes)
18
User Mode Access R
Values
Variable
Serial Number
Attribute #534
Unique serial number assigned in the manufacturing facility. This electronic output
matches the printout on the physical device label, for example M1J26F45V.
Type
S
Size (Bytes)
16
User Mode Access R
Values
Variable
Date of Manufacture
Attribute #535
Date of device manufacture assigned in the manufacturing facility. This electronic output
matches the printout on the physical device label, for example 30APR14 (which reads the
30th of April 2014).
Type
S
Size (Bytes)
7
User Mode Access R
Values
Variable
A-90
HS-360X Handheld DPM Scanner User Manual
Appendices
Date of First Programming
Attribute #614
Date of first electronic programming represents the first time settings where electronically
loaded to the scanner either by 123Scan or via SMS, for example 18MAY14 (which reads
the 18th of May 2014).
Type
S
Size (Bytes)
7
User Mode Access
R
Values
Variable
Configuration Filename
Attribute #616
The name assigned to the configuration settings loaded electronically to the device either
by 123Scan or via SMS.
Note: Scanning the Set Defaults programming symbol automatically changes the configuration filename to factory defaults.
To indicate the configuration settings loaded to the device were changed, the configuration
filename changes to Modified upon scanning any parameter programming symbol.
Type
S
Size (Bytes)
17
User Mode Access
RW
Values
Variable
Beeper/LED
Attribute #6000
Activates the beeper and/or LED.
Type
X
Size (Bytes)
N/A
User Mode Access
W
Values:
Beep / LED Action
Value
1 high short beep
0
2 high short beeps
1
3 high short beeps
2
4 high short beeps
3
5 high short beeps
4
1 low short beep
5
2 low short beeps
6
HS-360X Handheld DPM Scanner User Manual
A-91
Non-Parameter Attributes
3 low short beeps
4 low short beeps
5 low short beeps
1 high long beep
2 high long beeps
3 high long beeps
4 high long beeps
5 high long beeps
1 low long beep
2 low long beeps
3 low long beeps
4 low long beeps
5 low long beeps
Fast warble beep
Slow warble beep
High-low beep
Low-high beep
High-low-high beep
Low-high-low beep
High-high-low-low beep
Green LED off
Green LED on
Red LED on
Red LED off
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
42
43
47
48
Parameter Defaults
Attribute #6001
This attribute restores all parameters to their factory defaults.
Type
X
Size (Bytes)
N/A
User Mode Access
W
Values
0 = Restore Defaults
1 = Restore Factory Defaults
2 = Write Custom Defaults
A-92
HS-360X Handheld DPM Scanner User Manual
Appendices
Beep on Next Bootup
Attribute #6003
This attribute configures (enables or disables) beep on next boot up of scanner.
Type
X
Size (Bytes)
N/A
User Mode Access
W
Values
0 = Disable beep on next bootup
1 = Enable beep on next bootup
Reboot
Attribute #6004
This attribute initiates a device reboot.
Type
X
Size (Bytes)
N/A
User Mode Access
W
Values
N/A
Host Trigger Session
Attribute #6005
This attribute triggers a decode session similar to manually depressing the scanner trigger button.
Type
X
Size (Bytes)
N/A
User Mode Access
W
Values
1 = Start Host Trigger Session
0 = Stop Host Trigger Session
Firmware Version
Attribute #20004
The scanner's operating system version. For example, NBRFMAAC or PAAAABS00-007-R03D0.
Type
S
Size (Bytes)
Variable
User Mode Access
R
Values
Variable
HS-360X Handheld DPM Scanner User Manual
A-93
Non-Parameter Attributes
Scankit Version
Attribute #20008
Identifies the 1D decode algorithms resident on the device, for example SKIT4.33T02.
Type
S
Size (Bytes)
Variable
User Mode Access R
Values
Variable
ImageKit Version
Attribute #20013
Identifies the 2D decode algorithms resident on the device, for example IMGKIT_7.01T08.31.
Type
S
Size (Bytes)
Variable
User Mode Access R
Values
Variable
Copyright ©2019
Omron Microscan Systems, Inc.
All rights reserved. The information contained herein is proprietary and is provided solely for the purpose of
allowing customers to operate and/or service Omron Microscan-manufactured equipment and is not to be
released, reproduced, or used for any other purpose without written permission of Omron Microscan.
Throughout this manual, trademarked names might be used. We state herein that we are using the names
to the benefit of the trademark owner, with no intention of infringement.
A-94
HS-360X Handheld DPM Scanner User Manual
OMRON Corporation
Industrial Automation Company
Kyoto, JAPAN
Contact: www.ia.omron.com
Regional Headquarters
OMRON EUROPE B.V.
Wegalaan 67-69, 2132 JD Hoofddorp
The Netherlands
Tel: (31)2356-81-300/Fax: (31)2356-81-388
OMRON ELECTRONICS LLC
2895 Greenspoint Parkway, Suite 200
Hoffman Estates, IL 60169 U.S.A.
Tel: (1) 847-843-7900/Fax: (1) 847-843-7787
OMRON ASIA PACIFIC PTE. LTD.
No. 438A Alexandra Road # 05-05/08 (Lobby 2),
Alexandra Technopark,
Singapore 119967
Tel: (65) 6835-3011/Fax: (65) 6835-2711
OMRON (CHINA) CO., LTD.
Room 2211, Bank of China Tower,
200 Yin Cheng Zhong Road,
PuDong New Area, Shanghai, 200120, China
Tel: (86) 21-5037-2222/Fax: (86) 21-5037-2200
Authorized Distributor:
© OMRON Corporation 2019 All Rights Reserved.
In the interest of product improvement, specifications
are subject to change without notice.
Cat. No. 84-9000360-02
0519
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement