Microscan PanelScan PCB Traceability System Specification Sheet

Microscan PanelScan PCB Traceability System Specification Sheet
PanelSca n ™
Multi-Array PCB
Traceability System
PanelScan is a user-friendly and easily integrated
traceability solution for capturing barcode data
from multi-array PCBs at the front-end or midstream on any SMT line. This integrated system
replaces error-prone manual scanning with a
solution that allows for in-motion reading and
keeps production lines moving.
*Mounting structure is
not included.
Pa ne l S c a n : A t a G l anc e
The PanelScan system is the ideal traceability and
inspection solution for any high mix, low volume
electronics manufacturer.
• Inline decoding and verification of 1D/2D codes
• Scalable to Visionscape for additional inspection tasks
• Available in both Standard and Wide versions for flexible
implementation
• Solution includes software, camera, lens, light, trigger
and cables:
PanelScan Software: User-friendly interface to set up
and run jobs
GigE Camera: Up to two GigE line scan cameras and
telemetric lenses
NERLITE Smart Series Light: Up to two lights with
focused lens and brightest LEDs in their class
For more information on this product, visit www.microscan.com.
Pa ne l S c a n : U s e r Inte rfac e
Large Area Imaging
PanelScan is a cost-effective
large area imaging system
designed to read the entire
length and width of any
printed circuit board array.
Remote Configuration
After setup, line changes are
easily managed within the
software so that updates can
be configured remotely or
through automation. Product
mix and barcode location
changes no longer require
lengthy line shut-downs to
reposition, reconfigure, and
test barcode readers.
Easily Integrated
PanelScan is a packaged
solution that can be
integrated into almost any
production environment.
Built-in software application
utilities allow integration into
an existing Manufacturing
Execution System (MES).
Intuitive User Interface
The innovative PanelScan
interface is exceptionally easy
to use. Line operators can
quickly train and recall jobs
to make sure production is
always running.
Scalable Software
Easily upgrade to full
functionality of Visionscape®
software to access valueadded inspection tasks
such as absence/presence,
measurement, and OCR/OCV.
Application Examples
- Contract manufacturers
- Automotive electronics
- Medical electronics
- Military electronics
- Large-format PCB
assemblers
- Machine builders
- MES providers
- Material handling
P anel S can ™ S pecifications
and
O ptions
Mounting Specifications:
STANDARD CONFIGURATION
• One camera
• One light
• Field of view: 10" (254 mm) max. width by 24" length
WIDE CONFIGURATION
• Two cameras
• Two lights
• Field of view: 18" (457 mm) max. width by 24" length
Note: Inches [millimeters]. Nominal dimensions shown. Typical tolerances apply.
Camera Specifications:
Light Specifications:
MECHANICAL (CAMERA)
Height: 2.44" (62 mm)
Width: 2.20" (56 mm)
Depth: 1.42" (36 mm)
Weight: 8 oz. (240 g)
MECHANICAL
Height: 2.24" (57 mm)
Width: 11.81" (300 mm)
Depth: 2.07" (52.6 mm)
Weight: 50.16 oz. (1422 g)
MECHANICAL (F-MOUNT ADAPTER)
Height: 1.43” (36.4 mm)
Diameter: 2.32” (59 mm)
LIGHTING PARAMETERS
Lens: Collimating
Temperature: 5000 K – 8300 K
Continuous Output: 1813 lumens
MECHANICAL (LENS)
Height: 2.9" (74.5 mm)
Diameter: 2.8" (70 mm)
Weight: 15.5 oz. (440 g)
COMMUNICATION PROTOCOL
Interface: Gigabit Ethernet
LIGHT COLLECTION
Sensor: Linear CMOS, 1 by 6144 pixels
Line Rate: 17 kHz
ELECTRICAL
Power: 12–24 VDC (±5%)
Power Consumption: 4.5 W
DIGITAL I/O
3 in / 2 out or direct encoder input
LIGHT SOURCE
Type: High output LEDs
Expected Life: 50,000 hours
Eye Safety: EN 60825-1: Class 2
CONNECTOR
Input: M12 5-pin plug, A-code
Output: M12 5-pin socket, A-code
ELECTRICAL
Power: 20.2–28.8 VDC
Current Draw at 24 VDC (typ.): 750 mA
Continuous Operation: No additional signals required
Continuous Operation with Dimming: 0 VDC (LEDs
off) to 3.1–3.5 VDC (LEDs on) PWM signal. < 1 mA,
modulation frequency 2 KHz +/- 100 Hz. Note: LED
duty cycle will equal duty cycle of dimming signal
when using this mode.
Continuous Operation with On/Off Control: 0 VDC
(LEDs off) to 3.1–3.5 VDC (LEDs on), < 1 mA
MINIMUM PC REQUIREMENTS
• Windows® 7 64-bit
• 2 GB of memory
• Two GigE NIC ports with Intel® chip set
SYMBOLOGY TYPES
2D Symbologies: Data Matrix (ECC 0-200),
QR Code, Micro QR Code
Stacked Symbologies: PDF417, GS1 Databar
(Composite & Stacked)
Linear Barcodes: Code 39, Code 128, BC 412,
I 2 of 5, UPC/EAN, Pharmacode, Codabar,
Code 93
Narrow Bar Width Dimensions:
1D = 3.3 mil (0.0033"/0.08 mm)
2D = 5 mil (0.005"/0.13 mm)
QMS CERTIFICATION
www.microscan.com/quality
©2018 Omron Microscan Systems, Inc. SP084C-EN-0518
Read Range and other performance data is determined using high quality Grade
A symbols per ISO/IEC 15415 and ISO/IEC 15416 in a 25° C environment.
For application-specific Read Range results, testing should be performed with
symbols used in the actual application. Omron Microscan Applications
Engineering is available to assist with evaluations. Results may vary depending
on symbol quality. Warranty–For current warranty information on this product,
please visit www.microscan.com/warranty.
www.microscan.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement