Microscan Smart Series Pharmalite Configuration Guide

Microscan Smart Series Pharmalite Configuration Guide
NERLITE
Smart Series Pharmalite Illuminators
Configuration Guide
Part Number
Description
98-000228-01
98-9000137-01
Continuous Mode
Continuous Mode with Dimming
Or On-Off Control
High Output Strobe Mode
Continuous Current
Strobe Current
No Controller Required
(Can be connected directly
to 24VDC)
No Controller Required
(Can be connected directly
to 24VDC)
No Controller Required
(Can be connected directly
to 24VDC)
Smart Series Pharmalite
160 mA
850 mA
Figure A or D
Figure B (or D for On-Off Control
only)
Figure C
Smart Series Pharmalite for HAWK MV-4000
160 mA
850 mA
Figure A or D
Figure B (or D for On-Off Control
only)
Figure C
Hardware Required
Item
Description
Part Number
1
Smart Series Pharmalite
98-000228-01
1
Smart Series Pharmalite for HAWK MV-4000
98-9000137-01
2
Power Supply DSP60 24VDC 2.5A DIN Mount
NER-011504100
2
Power Supply DSP100 24VDC 4.2A DIN Mount
97-000006-01
3
Cable 5-Pin M12 Female-to-Flying Leads, 3 M
61-000186-01
3
Cable 5-Pin M12 Female-to-Flying Leads, 5 M
61-000187-01
4
Cable, Power Smart Series to QX-1 Continuous
61-000204-01
4
Cable, Power Smart Series to QX-1 On/Off
61-000207-01
Copyright ©2018 Omron Microscan Systems, Inc.
P/N 83-230019-02 Rev C
NERLITE Smart Series Pharmalite Illuminators
Accessories
Description
Part Number
Application
AC Power Cord US
NER-030028300
Power Cord For Power Supply
AC Power Cord EU
NER-030028400
Power Cord For Power Supply
AC Power Cord UK
NER-030028500
Power Cord For Power Supply
Connections:
Input Connector (M12 Male, 5 Circuit, A-Code)
Continuous Mode (Figures A & D):
Continuous Mode With Dimming (Figure B):
Continuous Mode With On-Off Control (Figure B):
High Output Strobe Mode (Figure C):
Continuous
Pin 1
+20.2-28.8VDC
+20.2-28.8VDC
+20.2-28.8VDC
+20.2-28.8VDC
On/Off
Pin 2
DC GND
DC GND
DC GND
TRIG (-)
Pin 3
DC GND
DC GND & DIM (-)
DC GND & DIM (-)
DC GND
Pin 4
+20.2-28.8VDC
+20.2-28.8VDC
+20.2-28.8VDC
TRIG (+)
Dimming
Pin 5
No Connection
Dim (+)
Dim (+)
No Connection
Backshell
Shield
Shield
Shield
Shield
Strobe
Control Signals
DIM (Continuous Mode with PWM Dimming):
0VDC (LEDs off) to 3.1-3.5VDC (LEDs on) pulse width modulated (PWM) signal , <1mA, Modulation Frequency 2KHz +/- 100Hz
Note: When using Continuous Mode with Dimming, the LED duty cycle will equal the duty cycle of the dimming signal.
DIM (Continuous Mode with On/Off Control):
TRIG (High Output Strobe Mode):
0VDC (LEDs off), 3.1-3.5VDC (LEDs on), (<1mA)
Optoisolated, 0VDC (LEDs off) to 3.1-28.8VDC (LEDs on), 10mA max, 20 μs min Trigger pulse width. Note: High Output Strobe internally limits LED frequency and pulse width
to a maximum of 90Hz and 1 ms respectively. Light output pulse will follow Trigger pulse width from 20 μs to 1 ms.
Note: When using Continuous Mode with Dimming, the LED duty cycle will equal the duty cycle of the dimming signal.
Cable Specifications:
Wire colors for flying lead cables:
Pin 1 = Brown
Pin 2 = White
Pin 3 = Blue
Pin 4 = Black
Pin 5 = Gray
Connector Nut = Shield
Note: Non-Omron Microscan cables may use different wire colors. It is the customer’s responsibility to make sure the light is connected correctly per the pin numbers in
the table above.
Copyright ©2018 Omron Microscan Systems, Inc.
www.microscan.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement